LM4902LDBD

LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 LM4902 Boomer™ Audio Power Amplifier Series 265mW at 3.3V Supply Audio Power Amplifier with Shutdown Mode Check for Samples: LM4902 FEATURES DESCRIPTION • • The LM4902 is a bridged audio power amplifier capable of delivering 265mW of continuous average power into an 8Ω load with 1% THD+N from a 3.3V power supply. 1 23 • • • • VSSOP and WSON Packaging No Output Coupling Capacitors, Bootstrap Capacitors, or Snubber Circuits are Necessary Thermal Shutdown Protection Circuitry Unity-Gain Stable External Gain Configuration Capability Latest Generation "Click and Pop" Suppression Circuitry APPLICATIONS • • • Cellular Phones PDA's Any Portable Audio Application KEY SPECIFICATIONS • • • Boomer™ audio power amplifiers were designed specifically to provide high quality output power from a low supply voltage while requiring a minimal amount of external components. Since the LM4902 does not require output coupling capacitors, bootstrap capacitors or snubber networks, it is optimally suited for low-power portable applications. The LM4902 features an externally controlled, low power consumption shutdown mode, and thermal shutdown protection. The closed loop response of the unity-gain stable LM4902 can be configured by external gain-setting resistors. THD+N at 1kHz for 265mW Continuous Average Output Power into 8Ω, VDD = 3.3V 1.0% (max) THD+N at 1kHz for 675mW Continuous Average Output Power into 8Ω, VDD = 5V 1.0% (max) Shutdown Current 0.1µA (typ) 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Boomer is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2001–2013, Texas Instruments Incorporated LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com Typical Application Figure 1. Typical Audio Amplifier Application Circuit Connection Diagrams Figure 2. VSSOP - Top View See Package Number DGK Figure 3. WSON - Top View See Package Number NGL These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 Absolute Maximum Ratings (1) (2) Supply Voltage 6.0V −65°C to +150°C Storage Temperature −0.3V to VDD + 0.3V Input Voltage Power Dissipation (3) Internally limited (4) 2000V ESD Susceptibility ESD Susceptibility (5) 200V Junction Temperature 150°C Soldering Information Small Outline Package Vapor Phase (60 sec.) 215°C Infrared (15 sec.) Thermal Resistance (1) (2) (3) (4) (5) 220°C θJC (VSSOP) 56°C/W θJA (VSSOP) 190°C/W θJA (WSON) 67°C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX − TA) / θJA or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4902, TJMAX = 150°C. The typical junction-to-ambient thermal resistance, when board mounted, is 190°C/W for package number DGK. Human body model, 100pF discharged through a 1.5kΩ resistor. Machine Model, 220pF–240pF discharged through all pins. Operating Ratings Temperature Range TMIN ≤ TA ≤ TMAX −40°C ≤ TA ≤ +85°C 2.0V ≤ VDD ≤ 5.5V Supply Voltage Electrical Characteristics (1) (2) The following specifications apply for VDD = 5V, for all available packages, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter Conditions IDD Quiescent Power Supply Current VIN = 0V, IO = 0A (6) ISD Shutdown Current VPIN1 =GND VOS Output Offset Voltage VIN = 0V PO Output Power THD = 1% (max); f = 1kHz; RL = 8Ω; THD+N (1) (2) (3) (4) (5) (6) Total Harmonic Distortion+Noise PO = 400 mWrms; AVD = 2; RL = 8Ω; 20Hz ≤ f ≤ 20kHz, BW < 80kHz LM4902 Typical (3) Limit (4) (5) Units (Limits) 4 6.0 mA (max) 0.1 5 μA (max) 5 50 mV (max) 675 300 mW (min) 0.4 % All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25°C and represent the parametric norm. Limits are specified to TI's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 3 LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com Electrical Characteristics(1)(2) (continued) The following specifications apply for VDD = 5V, for all available packages, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter Conditions LM4902 Typical (3) Limit (4) (5) Units (Limits) VRIPPLE = 200mV sine p-p PSRR (7) (8) 4 Power Supply Rejection Ratio f = 217Hz (7) 70 f = 1KHz (7) 67 f = 217Hz (8) 55 f = 1KHz (8) 55 dB Unterminated input. 10Ω terminated input. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 Electrical Characteristics (1) (2) The following specifications apply for VDD = 3.3V, for all available packages, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter Conditions IDD Quiescent Power Supply Current VIN = 0V, IO = 0A (6) ISD Shutdown Current VPIN1 = GND VOS Output Offset Voltage VIN = 0V PO Output Power THD = 1% (max); f = 1kHz; RL = 8Ω; THD+N Total Harmonic Distortion+Noise PO = 250 mWrms; AVD = 2; RL = 8Ω; 20Hz ≤ f ≤ 20kHz, BW < 80kHz LM4902 Typical (3) Limit (4) (5) Units (Limits) mA (max) 3 5 0.1 3 μA (max) 5 50 mV (max) 265 mW 0.4 % VRIPPLE = 200mV sine p-p PSRR (1) (2) (3) (4) (5) (6) (7) (8) Power Supply Rejection Ratio f = 217Hz (7) 73 f = 1KHz (7) 70 f = 217Hz (8) 60 f = 1KHz (8) 68 dB All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25°C and represent the parametric norm. Limits are specified to TI's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier. Unterminated input. 10Ω terminated input. Electrical Characteristics (1) (2) The following specifications apply for VDD = 2.6V, for all available packages, unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter Conditions LM4902 Typical (3) Limit (4) (5) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A (6) 2.6 4 mA (max) ISD Shutdown Current VPIN1 = VDD 0.1 2.0 μA (max) VOS Output Offset Voltage VIN = 0V PO Output Power THD = 1% (max); f = 1kHz; RL = 8Ω THD+N Total Harmonic Distortion+Noise 5 mV 130 mW 0.4 % f = 217Hz (7) 58 dB f = 1KHz (7) 63 PO = 100 mWrms; AVD = 2; RL = 8Ω; 20Hz ≤ f ≤ 20kHz, BW < 80kHz VRIPPLE = 200mV sine p-p PSRR (1) (2) (3) (4) (5) (6) (7) Power Supply Rejection Ratio All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25°C and represent the parametric norm. Limits are specified to TI's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier. 10Ω terminated input. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 5 LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com External Components Description (Figure 1) Components Functional Description 1. Ri Inverting input resistance which sets the closed-loop gain in conjunction with RF. This resistor also forms a high pass filter with Ci at fc = 1/(2π RiCI). 2. Ci Input coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Also creates a highpass filter with Ri at fc = 1/(2π RiCi). Refer to the section, PROPER SELECTION OF EXTERNAL COMPONENTS, for an explanation of how to determine the value of Ci. 3. RF Feedback resistance which sets the closed-loop gain in conjunction with Ri. 4. CS Supply bypass capacitor which provides power supply filtering. Refer to the POWER SUPPLY BYPASSING section for information concerning proper placement and selection of the supply bypass capacitor. 5. CB Bypass pin capacitor which provides half-supply filtering. Refer to the PROPER SELECTION OF EXTERNAL COMPONENTS for information concerning proper placement and selection of CB. 6 Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 Typical Performance Characteristics THD+N vs Frequency THD+N vs Frequency Figure 4. Figure 5. THD+N vs Frequency THD+N vs Frequency Figure 6. Figure 7. THD+N vs Frequency THD+N vs Frequency Figure 8. Figure 9. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 7 LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) 8 THD+N vs Frequency THD+N vs Frequency Figure 10. Figure 11. THD+N vs Frequency THD+N vs Frequency Figure 12. Figure 13. THD+N vs Frequency THD+N vs Output Power Figure 14. Figure 15. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 Typical Performance Characteristics (continued) THD+N vs Output Power THD+N vs Output Power Figure 16. Figure 17. THD+N vs Output Power THD+N vs Output Power Figure 18. Figure 19. THD+N vs Output Power THD+N vs Output Power Figure 20. Figure 21. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 9 LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) 10 THD+N vs Output Power THD+N vs Output Power Figure 22. Figure 23. THD+N vs Output Power THD+N vs Output Power Figure 24. Figure 25. Output Power vs Supply Voltage Output Power vs Supply Voltage Figure 26. Figure 27. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 Typical Performance Characteristics (continued) Output Power vs Supply Voltage Output Power vs Supply Voltage Figure 28. Figure 29. Output Power vs Load Resistance Power Dissipation vs Output Power Figure 30. Figure 31. Power Dissipation vs Output Power Power Dissipation vs Output Power Figure 32. Figure 33. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 11 LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) 12 Clipping Voltage vs Supply Voltage Noise Floor Figure 34. Figure 35. Noise Floor Frequency Response vs Input Capacitor Size Figure 36. Figure 37. Power Supply Rejection Ratio Power Supply Rejection Ratio Figure 38. Figure 39. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 Typical Performance Characteristics (continued) Power Supply Rejection Ratio Power Supply Rejection Ratio Figure 40. Figure 41. Power Supply Rejection Ratio vs Supply Voltage Power Supply Rejection Ratio vs Supply Voltage Figure 42. Figure 43. Power Derating Curve Supply Current vs Supply Voltage Figure 44. Figure 45. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 13 LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Open Loop Frequency Response Figure 46. 14 LM4902NGL Power Derating Curve This curve shows the LM4902NGL's thermal dissipation ability at different ambient temperatures given the exposed-DAP of the part is soldered to a plane of 1oz. Cu with an area given in the label of each curve. Figure 47. Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 APPLICATION INFORMATION EXPOSED-DAP PACKAGE PCB MOUNTING CONSIDERATION The LM4902's exposed-DAP (die-attach paddle) package (NGL) provides a low thermal resistance between the die and the PCB to which the part is mounted and soldered. This allows rapid heat from the die to the surrounding PCB copper traces, ground plane, and surrounding air. This allows the LM4902NGL to operate at higher output power levels in higher ambient temperatures than the DGK package. Failing to optimize thermal design may compromise the high power performance and activate unwanted, though necessary, thermal shutdown protection. The NGL package must have its DAP soldered to a copper pad on the PCB. The DAP's PCB copper pad is connected to a large plane of continuous unbroken copper. This plane forms a thermal mass, heat sink, and radiation area. Place the heat sink area on either outside plane in the case of a two-sided PCB, or on an inner layer of a board with more than two layers. Connect the DAP copper pad to the inner layer or backside copper heat sink area with 2 vias. The via diameter should be 0.012in - 0.013in with a 1.27mm pitch. Ensure efficient thermal conductivity by plating through the vias. Best thermal performance is achieved with the largest practical heat sink area. The power derating curve in the Typical Performance Characteristics shows the maximum power dissipation versus temperature for several different areas of heat sink area. Placing the majority of the heat sink area on another plane is preferred as heat is best dissipated through the bottom of the chip. For further detailed and specific information concerning PCB layout, fabrication, and mounting an NGL (WSON) package, see the AN-1187 Application Report (Literature Number SNOA401). BRIDGE CONFIGURATION EXPLANATION As shown in Figure 1, the LM4902 has two operational amplifiers internally, allowing for a few different amplifier configurations. The first amplifier's gain is externally configurable, while the second amplifier is internally fixed in a unity-gain, inverting configuration. The closed-loop gain of the first amplifier is set by selecting the ratio of RF to Ri while the second amplifier's gain is fixed by the two internal 20kΩ resistors. Figure 1 shows that the output of amplifier one serves as the input to amplifier two which results in both amplifiers producing signals identical in magnitude, but out of phase 180°. Consequently, the differential gain for the IC is AVD = 2*(RF/Ri) (1) By driving the load differentially through outputs Vo1 and Vo2, an amplifier configuration commonly referred to as “bridged mode” is established. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of its load is connected to ground. A bridge amplifier design has a few distinct advantages over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. In order to choose an amplifier's closedloop gain without causing excessive clipping, please refer to the AUDIO POWER AMPLIFIER DESIGN section. A bridge configuration, such as the one used in LM4902, also creates a second advantage over single-ended amplifiers. Since the differential outputs, Vo1 and Vo2, are biased at half-supply, no net DC voltage exists across the load. This eliminates the need for an output coupling capacitor which is required in a single supply, singleended amplifier configuration. If an output coupling capacitor is not used in a single-ended configuration, the halfsupply bias across the load would result in both increased internal lC power dissipation as well as permanent loudspeaker damage. POWER DISSIPATION Power dissipation is a major concern when designing a successful amplifier, whether the amplifier is bridged or single-ended. Equation 2 states the maximum power dissipation point for a bridge amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (VDD)2/(2π2RL) Single-Ended (2) However, a direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation point for a bridge amplifier operating at the same conditions. PDMAX = 4(VDD)2/(2π2RL) Bridge Mode (3) Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 15 LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com Since the LM4902 has two operational amplifiers in one package, the maximum internal power dissipation is 4 times that of a single-ended amplifier. Even with this substantial increase in power dissipation, the LM4902 does not require heatsinking. From Equation 2, assuming a 5V power supply and an 8Ω load, the maximum power dissipation point is 625 mW. The maximum power dissipation point obtained from Equation 3 must not be greater than the power dissipation that results from Equation 4: PDMAX = (TJMAX − TA)/θJA (4) For package DGK, θJA = 190°C/W. TJMAX = 150°C for the LM4902. Depending on the ambient temperature, TA, of the system surroundings, Equation 4 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 3 is greater than that of Equation 4, then either the supply voltage must be decreased, the load impedance increased, the ambient temperature reduced, or the θJA reduced with heatsinking. In many cases larger traces near the output, VDD, and Gnd pins can be used to lower the θJA. The larger areas of copper provide a form of heatsinking allowing a higher power dissipation. For the typical application of a 5V power supply, with an 8Ω load, the maximum ambient temperature possible without violating the maximum junction temperature is approximately 30°C provided that device operation is around the maximum power dissipation point. Internal power dissipation is a function of output power. If typical operation is not around the maximum power dissipation point, the ambient temperature can be increased. Refer to the Typical Performance Characteristics POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitor location on both the bypass and power supply pins should be as close to the device as possible. The effect of a larger half supply bypass capacitor is improved PSRR due to increased half-supply stability. Typical applications employ a 5V regulator with 10μF and a 0.1μF bypass capacitors which aid in supply stability, but do not eliminate the need for bypassing the supply nodes of the LM4902. The selection of bypass capacitors, especially CB, is thus dependent upon desired PSRR requirements, click and pop performance as explained in the section, PROPER SELECTION OF EXTERNAL COMPONENTS, system cost, and size constraints. SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the LM4902 contains a shutdown pin to externally turn off the amplifier's bias circuitry. This shutdown feature turns the amplifier off when a logic low is placed on the shutdown pin. The trigger point between a logic low and logic high level is typically half supply. It is best to switch between ground and supply to provide maximum device performance. By switching the shutdown pin to GND, the LM4902 supply current draw will be minimized in idle mode. While the device will be disabled with shutdown pin voltages greater than GND, the idle current may be greater than the typical value of 0.1μA. In either case, the shutdown pin should be tied to a definite voltage to avoid unwanted state changes. In many applications, a microcontroller or microprocessor output is used to control the shutdown circuitry which provides a quick, smooth transition into shutdown. Another solution is to use a single-pole, single-throw switch in conjunction with an external pull-up resistor. When the switch is closed, the shutdown pin is connected to ground and disables the amplifier. If the switch is open, then the external pull-up resistor will enable the LM4902. This scheme ensures that the shutdown pin will not float, thus preventing unwanted state changes. PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers is critical to optimize device and system performance. While the LM4902 is tolerant to a variety of external component combinations, consideration to component values must be used to maximize overall system quality. The LM4902 is unity-gain stable, giving a designer maximum system flexibility. The LM4902 should be used in low gain configurations to minimize THD+N values, and maximize the signal to noise ratio. Low gain configurations require large input signals to obtain a given output power. Input signals equal to or greater than 1 Vrms are available from sources such as audio codecs. Please refer to the section, AUDIO POWER AMPLIFIER DESIGN, for a more complete explanation of proper gain selection. Besides gain, one of the major considerations is the closed-loop bandwidth of the amplifier. To a large extent, the bandwidth is dictated by the choice of external components shown in Figure 1. The input coupling capacitor, Ci, forms a first order high pass filter which limits low frequency response. This value should be chosen based on needed frequency response for a few distinct reasons. 16 Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 Selection of Input Capacitor Size Large input capacitors are both expensive and space hungry for portable designs. Clearly, a certain sized capacitor is needed to couple in low frequencies without severe attenuation. But in many cases the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. In this case using a large input capacitor may not increase system performance. In addition to system cost and size, click and pop performance is effected by the size of the input coupling capacitor, Ci. A larger input coupling capacitor requires more charge to reach its quiescent DC voltage (nominally ½ VDD). This charge comes from the output via the feedback and is apt to create pops upon device enable. Thus, by minimizing the capacitor size based on necessary low frequency response, turn-on pops can be minimized. Besides minimizing the input capacitor size, careful consideration should be paid to the bypass capacitor value. Bypass capacitor, CB, is the most critical component to minimize turn-on pops since it determines how fast the LM4902 turns on. The slower the LM4902's outputs ramp to their quiescent DC voltage (nominally ½ VDD), the smaller the turn-on pop. Choosing CB equal to 1.0 μF along with a small value of Ci (in the range of 0.1μF to 0.39μF), should produce a clickless and popless shutdown function. While the device will function properly, (no oscillations or motorboating), with CB equal to 0.1μF, the device will be much more susceptible to turn-on clicks and pops. Thus, a value of CB equal to 1.0μF or larger is recommended in all but the most cost sensitive designs. AUDIO POWER AMPLIFIER DESIGN Design a 300 mW/8Ω Audio Amplifier Given: Power Output 300mWrms Load Impedance 8Ω Input Level 1Vrms Input Impedance 20kΩ Bandwidth 100Hz–20 kHz ± 0.25dB A designer must first determine the minimum supply rail to obtain the specified output power. By extrapolating from the Output Power vs Supply Voltage graphs in the Typical Performance Characteristics section, the supply rail can be easily found. A second way to determine the minimum supply rail is to calculate the required Vopeak using Equation 5 and add the dropout voltage. Using this method, the minimum supply voltage would be (Vopeak + (2*VOD)), where VOD is extrapolated from the Dropout Voltage vs Supply Voltage curve in the Typical Performance Characteristics section. (5) Using the Output Power vs Supply Voltage graph for an 8Ω load, the minimum supply rail is 3.5V. But since 5V is a standard supply voltage in most applications, it is chosen for the supply rail. Extra supply voltage creates headroom that allows the LM4902 to reproduce peaks in excess of 700 mW without producing audible distortion. At this time, the designer must make sure that the power supply choice along with the output impedance does not violate the conditions explained in the POWER DISSIPATION section. Once the power dissipation equations have been addressed, the required differential gain can be determined from Equation 6. (6) (7) RF/Ri = AVD/2 From Equation 6, the minimum AVD is 1.55; use AVD = 2. Since the desired input impedance was 20 kΩ, and with a AVD of 2, a ratio of 1:1 of RF to Ri results in an allocation of Ri = RF = 20 kΩ. The final design step is to address the bandwidth requirements which must be stated as a pair of −3 dB frequency points. Five times away from a pole gives 0.17 dB down from passband response which is better than the required ±0.25 dB specified. fL = 100Hz/5 = 20Hz (8) Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 17 LM4902 SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 www.ti.com fH = 20kHz × 5 = 100kHz (9) As stated in the External Components Description section, Ri in conjunction with Ci create a highpass filter. Ci ≥ 1/(2π*20 kΩ*20 Hz) = 0.397μF; use 0.39μF (10) (11) The high frequency pole is determined by the product of the desired high frequency pole, fH, and the differential gain, AVD. With a AVD = 2 and fH = 100kHz, the resulting GBWP = 100kHz which is much smaller than the LM4902 GBWP of 25MHz. This figure displays that if a designer has a need to design an amplifier with a higher differential gain, the LM4902 can still be used without running into bandwidth problems. DIFFERENTIAL AMPLIFIER CONFIGURATION FOR LM4902 18 Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 LM4902 www.ti.com SNAS150D – DECEMBER 2001 – REVISED APRIL 2013 REVISION HISTORY Changes from Revision C (May 2013) to Revision D • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 18 Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: LM4902 19 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) LM4902MM/NOPB ACTIVE VSSOP DGK 8 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 GC3 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of