LM4919MM/NOPB

LM4919 LM4919 1.5V, Mono 85mW BTL Output, 14mW Stereo Headphone Audio Amplifier Literature Number: SNAS232A September 30, 2011 1.5V, Mono 85mW BTL Output, 14mW Stereo Headphone Audio Amplifier General Description Key Specifications The unity gain stable LM4919 is both a mono-BTL audio power amplifier and a Single Ended (SE) stereo headphone amplifier. Operating on a single 1.5V supply, the mono BTL mode delivers 85mW into an 8Ω load at 1% THD+N. In Single Ended stereo headphone mode, the amplifier delivers 14mW per channel into a 16Ω load at 1% THD+N. With the LM4919 packaged in the MM package, the customer benefits include low profile and small size. This package minimizes PCB area and maximizes output power. The LM4919 features circuitry that reduces output transients ("clicks" and "pops") during device turn-on and turn-off, an externally controlled, low-power consumption, active-low shutdown mode, and thermal shutdown. Boomer audio power amplifiers are designed specifically to use few external components and provide high quality output power in a surface mount package. ■ ■ ■ ■ ■ ■ ■ Mono-BTL output power (RL = 8Ω, VDD = 1.5V, THD+N = 1%) 85mW (typ) Stereo Headphone output power (RL = 16Ω, VDD = 1.5V, THD+N = 1%) 14mW (typ) Micropower shutdown current 0.02µA (typ) Supply voltage operating range 0.9V < VDD < 2.5V PSRR 1kHz, VDD = 1.5V, RL = 16Ω 72dB (typ) Features ■ Single-cell 0.9V to 2.5V battery operation ■ BTL mode for mono speaker ■ Single ended headphone operation with coupling ■ ■ ■ ■ ■ capacitors Unity-gain stable "Click and pop" suppression circuitry Active low micropower shutdown Low current, active-low mute mode Thermal shutdown protection circuitry Applications ■ Portable one-cell audio products ■ Portable one-cell electronic devices Typical Application 20082101 FIGURE 1. Block Diagram Boomer® is a registered trademark of National Semiconductor Corporation. © 2011 National Semiconductor Corporation 200821 200821 Version 2 Revision 3 www.national.com Print Date/Time: 2011/09/30 15:48:41 LM4919 1.5V, Mono 85mW BTL Output, 14mW Stereo Headphone Audio Amplifier OBSOLETE LM4919 LM4919 Connection Diagrams MSOP Package 20082102 Top View Order Number LM4919MM See NS Package Number MUB10A for MSOP MSOP Marking 200821f9 Z - Plant Code X - Date Code T - Die Traceability G - Boomer Family B6 - LM4919MM www.national.com 2 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 LM4919 Typical Connections 20082103 FIGURE 2. Typical Single Ended Output Configuration Circuit 20082105 FIGURE 3. Typical BTL Speaker Configuration Circuit 3 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 www.national.com LM4919 Junction Temperature Thermal Resistance Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Storage Temperature Input Voltage Power Dissipation (Note 2) ESD Susceptibility(Note 3) ESD Susceptibility (Note 4) 150°C  θJA (typ) MUB10A 175°C/W Operating Ratings 3.6V −65°C to +150°C −0.3V to VDD +0.3V Internally limited 2000V 200V Temperature Range TMIN ≤ TA ≤ TMAX Supply Voltage −40°C ≤ TA ≤ 85°C 0.9V ≤ VDD ≤ 2.5V Electrical Characteristics for the LM4919 (Note 1, Note 5) The following specifications apply for the circuit shown in Figure 4 operating with VDD = 1. 5V, unless otherwise specified. Limits apply for TA = 25°C. LM4919 Symbol Parameter Conditions Typical (Note 6) VDD Supply Voltage (Notes 10, 11) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A, RL = ∞ (Note 8) 0.9 ISD Shutdown Current VSHUTDOWN = GND 0.02 VOS Output Offset Voltage BTL Limit (Note 7) 0.9 Units (Limits) V (min) 2.5 V (max) 1.4 mA (max) μA 5 50 RL = 8Ω BTL, THD+N = 1% 85 70 RL = 16Ω SE, THD+N = 1% 14 mV (max) f = 1kHz PO Output Power (Note 9) THD+N Total Harmonic Distortion + Noise VNO Output Voltage Noise IMUTE Mute Current Crosstal k RL = 8Ω, BTL, PO = 25mW, f = 1kHz 0.2 RL = 16Ω, SE, PO = 5mW, f = 1kHz 0.07 mW (min) mW (min) 0.5 % (max) 20Hz to 20kHz, A-weighted SE 10 µVRMS 20Hz to 20kHz, A-weighted BTL 15 µVRMS VMUTE = 0, SE 15 µA RL = 16Ω, SE 55 dB 70 dB 72 dB VRIPPLE = 200mVP-P PSRR Power Supply Rejection Ratio CBYPASS = 4.7µF, RL = 8Ω f = 1kHz, BTL VRIPPLE = 200mVP-P sine wave CBYPASS = 4.7µF, RL = 16Ω f = 1kHz, SE VIH Control Logic High 0.9 V VIL Control Logic Low 0.3 V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 2: The maximum power dissipation is dictated by TJMAX, θJA, and the ambient temperature TA and must be derated at elevated temperatures. The maximum allowable power dissipation is PDMAX = (TJMAX − TA)/θJA. For the LM4919, TJMAX = 150°C. For the θJAs, please see the Application Information section or the Absolute Maximum Ratings section. Note 3: Human body model, 100pF discharged through a 1.5kΩ resistor. Note 4: Machine model, 220pF–240pF discharged through all pins. Note 5: All voltages are measured with respect to the ground (GND) pins unless otherwise specified. Note 6: Typicals are measured at 25°C and represent the parametric norm. Note 7: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 8: The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier. Note 9: Output power is measured at the device terminals. www.national.com 4 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 LM4919 Typical Performance Characteristics THD+N vs Frequency VDD = 1.5V, PO = 5mW, RL = 16Ω AV = –1, Single Ended Output THD+N vs Frequency VDD = 1.5V, RL = 8Ω, PO = 25mW AV = -1, BTL Output 20082112 20082113 THD+N vs Frequency VDD = 1.2V, PO = 5mW RL = 16Ω, AV = -1, Single Ended Output THD+N vs Frequency VDD = 1.2V, RL = 8Ω, PO = 25mW AV = -1, BTL Output 20082111 20082114 5 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 www.national.com LM4919 THD+N vs Output Power VDD = 1.5V, RL = 16Ω, f = 1kHz AV = -1, Single Ended Output THD+N vs Output Power VDD = 1.5V, RL = 8Ω, f = 1kHz AV = -1, BTL Output 20082115 20082117 THD+N vs Output Power VDD = 1.2V, RL = 16Ω, f = 1kHz AV = -1, Single Ended Output THD+N vs Output Power VDD = 1.2V, RL = 8Ω, f = 1kHz AV = -1, BTL Output 20082116 20082118 www.national.com 6 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 LM4919 Output Power vs Supply Voltage f = 1kHz, RL = 16Ω, AV = -1, Single Ended Output Output Powe rvs Supply Voltage f = 1kHz, RL = 8Ω, AV = -1, BTL Output 20082106 20082107 Output Power vs Load Resistance VDD = 1.5V, f = 1kHz Single Ended Output, AV = -1 Output Power vs Load Resistance VDD = 1.5V, f = 1kHz BTL Output, AV = -1 200821e6 200821e5 7 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 www.national.com LM4919 Output Power vs Load Resistance VDD = 1.2V, RL = 16Ω, f = 1kHz Single Ended Output, AV = -1 Output Power vs Load Resistance VDD = 1.2V, RL = 8Ω, f = 1kHz BTL Output, AV = -1 200821e4 200821e3 Power Dissipation vs Output Power f = 1kHz, AV = -1 Single Ended Output, Both Channels Power Dissipation vs Output Power f = 1kHz, AV = -1 BTL Output 20082124 www.national.com 20082123 8 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 LM4919 Channel Separation RL = 16Ω, PO = 5mW Single Ended Output, AV = -1 Power Supply Rejection Ratio VDD = 1.5V, VRIPPLE = 200mVPP RL = 16Ω, Single Ended Output Input Terminated into 10Ω 20082110 20082121 Power Supply Rejection Ratio VDD = 1.5V, VRIPPLE = 200mVPP RL = 8Ω, BTL Output Input Terminated into 10Ω Power Supply Rejection Ratio VDD = 1.2V, VRIPPLE = 200mVPP RL = 16Ω, Single Ended Output Input Terminated into 10Ω 20082120 20082122 9 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 www.national.com LM4919 Power Supply Rejection Ratio VDD = 1.2V, VRIPPLE = 200mVPP RL = 8Ω, BTL Output Input Terminated into 10Ω Frequency Response vs Input Capacitor Size VDD = 1.5V, RL = 16Ω AV = -1, BW < 80kHz, Single Ended Output 200821f8 20082119 Supply Voltage vs Supply Current Clipping Voltage vs Supply Voltage 200821e2 200821f1 Noise Floor VDD = 1.5V, RL = 8Ω BW < 80kHz, BTL Output Noise Floor VDD = 1.5V, RL = 16Ω BW < 80kHz, Single Ended Output 20082109 www.national.com 20082108 10 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 LM4919 Shutdown Hysteresis Voltage VDD = 1.5V Power Derating Curve VDD = 1.5V 200821f4 200821e1 Mute Attenuation vs Load Resistance Shutdown Current Distribution 200821f7 200821f2 11 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 www.national.com LM4919 closed-loop gain without causing excessive clipping, please refer to the Audio Power Amplifier Design section. A bridge configuration, such as the one used in LM4919, also creates a second advantage over single-ended amplifiers. Since the differential outputs, Vo1 and Vo2, are biased at halfsupply, no net DC voltage exists across the load. This eliminates the need for an output coupling capacitor which is required in a single supply, single-ended amplifier configuration. Application Information SINGLE ENDED (SE) CONFIGURATION EXPLANATION As shown in Figure 2, the LM4919 has two operational amplifiers internally, which have externally configurable gain. The closed loop gain of the two configurable amplifiers is set by selecting the ratio of Rf to Ri. Consequently, the gain for each channel of the IC is AVD = -(Rf / Ri) MODE SELECT DETAIL The LM4919 can be configured in either Single Ended or BTL mode (see Figure 2 and Figure 3). The default state of the LM4919 at power up is single ended. During initial power up or return from shutdown, the LM4919 must detect the correct mode of operation by sensing the status of the SE/BTL pin. When the bias voltage of the part ramps up to 60mV (as seen on the Bypass pin), an internal comparator detects the status of SE/BTL; and at 10mV, latches that value in place. Ramp up of the bias voltage will proceed at a different rate from this point on depending upon operating mode. BTL mode will ramp up about 11 times faster than Single Ended mode. Shutdown is not a valid command during this time period (TWU) and should not enabled to ensure a proper power on reset (POR) signal. In addition, the slew rate of VDD must be greater than 2.5V/ms to ensure reliable POR. Recommended power up timing is shown in Figure 5 along with proper usage of Shutdown and Mute. The mode-select circuit is suspended during CB discharge time. The circuit shown in Figure 4 presents an applications solution to the problem of using different supply voltages with different turn-on times in a system with the LM4919. This circuit shows the LM4919 with a 25-50kΩ. Pull-up resistor connected from the shutdown pin to VDD. The shutdown pin of the LM4919 is also being driven by an open drain output of an external microcontroller on a separate supply. This circuit ensures that shutdown is disabled when powering up the LM4919 by either allowing shutdown to be high before the LM4919 powers on (the microcontroller powers up first) or allows shutdown to ramp up with VDD (the LM4919 powers up first). This will ensure the LM4919 powers up properly and enters the correct mode of operation. Please note that the SE/BTL pin (Pin 8) should be tied to GND for Single Ended mode, and to VDD for BTL mode. When the LM4919 operates in Single Ended mode, coupling capacitors are used on each output (VoA and VoB) and the SE/BTL pin (Pin 8) is connected to ground. These output coupling capacitors blocks the half supply voltage to which the output amplifiers are typically biased and couples the audio signal to the headphones or other single-ended (SE) loads. The signal return to circuit ground is through the headphone jack's sleeve. BRIDGED (BTL) CONFIGURATION EXPLANATION As shown in Figure 3, the LM4919 has two internal operational amplifiers. The first amplifier's gain is externally configurable, while the second amplifier should be externally fixed in a unity-gain, inverting configuration. The closed-loop gain of the first amplifier is set by selecting the ratio of Rf to Riwhile the second amplifier's gain should be fixed by the two external 20kΩ resistors. Figure 3 shows that the output of amplifier one serves as the input to amplifier two which results in both amplifiers producing signals identical in magnitude, but out of phase by 180°. Consequently, the differential gain for the IC is AVD = 2 *(Rf / Ri). By driving the load differentially through outputs Vo1 and Vo2, an amplifier configuration commonly referred to as "bridged mode" is established. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of the load is connected to ground. A bridge amplifier design has a few distinct advantages over the single-ended configuration. It provides a differential drive to the load, thus doubling output swing for a specified supply voltage. Four times the output power is possible as compared to a singleended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. In order to choose an amplifier's www.national.com 12 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 LM4919 20082153 FIGURE 4. Recommended Circuit for Different Supply Turn-On Timing 20082154 FIGURE 5. Turn-On, Shutdown, and Mute Timing for Single-Ended 13 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 www.national.com LM4919 trigger point varies depending on supply voltage and is shown in the Shutdown Hysteresis Voltage graphs in the Typical Performance Characteristics section. The low 0.02µA (typ) shutdown current is achieved by applying a voltage that is as near as ground as possible to the SHUTDOWN pin. A voltage that is higher than ground may increase the shutdown current. There are a few ways to control the micro-power shutdown. These include using a single-pole, single-throw switch, a microprocessor, or a microcontroller. When using a switch, connect an external 100kΩ pull-up resistor between the SHUTDOWN pin and VDD. Connect the switch between the SHUTDOWN pin and ground. Select normal amplifier operation by opening the switch. Closing the switch connects the SHUTDOWN pin to ground, activating micro-power shutdown. The switch and resistor guarantee that the SHUTDOWN pin will not float. This prevents unwanted state changes. In a system with a microprocessor or microcontroller, use a digital output to apply the control voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin with active circuitry eliminates the pull-up resistor. POWER DISSIPATION Power dissipation is a major concern when designing a successful amplifier, whether the amplifier is bridged or singleended. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. Since the LM4919 has two operational amplifiers in one package, the maximum internal power dissipation is 4 times that of a single-ended amplifier. The maximum power dissipation for a given BTL application can be derived from the power dissipation graphs or from Equation 1. PDMAX = 4*(VDD) 2 / (2π2RL) (1) When operating in Single Ended mode, Equation 2 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (VDD) 2 / (2π2RL) (2) Since the LM4919 has two operational amplifiers in one package, the maximum internal power dissipation point is twice that of the number that results from Equation 2. From Equation 2, assuming a 1.5V power supply and a 16Ω load, the maximum power dissipation point is 7mW per amplifier. Thus the maximum package dissipation point is 14mW. The maximum power dissipation point obtained from either Equations 1, 2 must not be greater than the power dissipation that results from Equation 3: PDMAX = (TJMAX - TA) / θJA MUTE When in single ended mode, the LM4919 also features a mute function that enables extremely fast turn-on/turn-off with a minimum of output pop and click with a low current consumption (≤20µA, typical). The mute function leaves the outputs at their bias level, thus resulting in higher power consumption than shutdown mode, but also provides much faster turn on/ off times. Providing a logic low signal on the MUTE pin enables mute mode. Threshold voltages and activation techniques match those given for the shutdown function as well. Mute may not appear to function when the LM4919 is used to drive high impedance loads. This is because the LM4919 relies on a typical headphone load (16-32Ω) to reduce input signal feed-through through the input and feedback resistors. Mute attenuation can thus be calculated by the following formula: (3) For package MUB10A, θJA = 175°C/W. TJMAX = 150°C for the LM4919. Depending on the ambient temperature, TA, of the system surroundings, Equation 3 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 1 or 2 is greater than that of Equation 3, then either the supply voltage must be decreased, the load impedance increased or TA reduced. For the typical application of a 1.5V power supply, with a 16Ω load, the maximum ambient temperature possible without violating the maximum junction temperature is approximately 146°C provided that device operation is around the maximum power dissipation point. Thus, for typical applications, power dissipation is not an issue. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature may be increased accordingly. Refer to the Typical Performance Characteristics curves for power dissipation information for lower output powers. Mute Attenuation (dB) = 20Log[RL / (Ri+RF)] Parallel load resistance may be necessary to achieve satisfactory mute levels when the application load is known to be high impedance. The mute function, described above, is not necessary when the LM4919 is operating in BTL mode since the shutdown function operates quickly in BTL mode with less power consumption than mute. In these modes, the Mute signal is equivalent to the Shutdown signal. Mute may be enabled during shutdown transitions, but should not be toggled for a brief period immediately after exiting or entering shutdown. These brief time periods are labeled X1 (time after returning from shutdown) and X2 (time after entering shutdown) and are shown in the timing diagram given in Figure 5. X1 occurs immediately following a return from shutdown (TWU) and lasts 40ms±25%. X2 occurs after the part is placed in shutdown and the decay of the bias voltage has occurred (2.2*250k*CB) and lasts for 100ms±25%. The timing of these transition periods relative to X1 and X2 is also shown in Figure 5. While in single ended mode, mute should not be toggled during these time periods, but may be toggled during the shutdown transitions or any other time the part is in normal operation. Failure to operate mute correctly may result in much higher click and pop values or failure of the device to mute at all. POWER SUPPLY BYPASSING As with any amplifier, proper supply bypassing is important for low noise performance and high power supply rejection. The capacitor location on the power supply pins should be as close to the device as possible. Typical applications employ a battery (or 1.5V regulator) with 10µF tantalum or electrolytic capacitor and a ceramic bypass capacitor that aid in supply stability. This does not eliminate the need for bypassing the supply nodes of the LM4919. A bypass capacitor value in the range of 0.1µF to 1µF is recommended. MICRO POWER SHUTDOWN The voltage applied to the SHUTDOWN pin controls the LM4919's shutdown function. Activate micro-power shutdown by applying a logic-low voltage to the SHUTDOWN pin. When active, the LM4919's micro-power shutdown feature turns off the amplifier's bias circuitry, reducing the supply current. The www.national.com PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers is critical to optimize device and system performance. While the LM4919 is tolerant of external 14 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 plifier outputs are reconnected to their respective output pins. Although the BYPASS pin current cannot be modified, changing the size of CB alters the device's turn-on time. There is a linear relationship between the size of CB and the turn-on time. Here are some typical turn-on times for various values of CB: Single-Ended CB(µF) TON 0.1 117ms 0.22 179ms 0.47 310ms 1.0 552ms 2.2 1.14s 4.7 2.4s BTL SELECTION OF INPUT CAPACITOR SIZE Amplifying the lowest audio frequencies requires a high value input coupling capacitor, Ci. A high value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases, however, the headphones used in portable systems have little ability to reproduce signals below 60Hz. Applications using headphones with this limited frequency response reap little improvement by using a high value input capacitor. In addition to system cost and size, turn on time is affected by the size of the input coupling capacitor Ci. A larger input coupling capacitor requires more charge to reach its quiescent DC voltage. This charge comes from the output via the feedback. Thus, by minimizing the capacitor size based on necessary low frequency response, turn-on time can be minimized. A small value of Ci (in the range of 0.1µF to 0.47µF), is recommended. CB(µF) TON (ms) 0.1 72 0.22 79 0.47 89 1.0 112 2.2 163 4.7 283 In order to eliminate "clicks and pops", all capacitors must be discharged before turn-on. Rapidly switching VDD may not allow the capacitors to fully discharge, which may cause "clicks and pops". AUDIO POWER AMPLIFIER DESIGN A 25mW/32Ω Audio Amplifier Bypass Capacitor Value Selection Besides minimizing the input capacitor size, careful consideration should be paid to value of CB, the capacitor connected to the BYPASS pin. Since CB determines how fast the LM4919 settles to quiescent operation, its value is critical when minimizing turn-on pops. The slower the LM4919's outputs ramp to their quiescent DC voltage (nominally VDD/2), the smaller the turn-on pop. Choosing CB equal to 4.7µF along with a small value of Ci (in the range of 0.1µF to 0.47µF), produces a click-less and pop-less shutdown function. As discussed above, choosing Ci no larger than necessary for the desired bandwidth helps minimize clicks and pops. This ensures that output transients are eliminated when power is first applied or the LM4919 resumes operation after shutdown. Given: Power Output Load Impedance Input Level Input Impedance 16Ω 0.4Vrms 20kΩ A designer must first choose a mode of operation (SE or BTL) and determine the minimum supply rail to obtain the specified output power. By extrapolating from the Output Power vs. Supply Voltage graphs in the Typical Performance Characteristics section, the supply rail can be easily found. 1.5V is a standard voltage in most applications, it is chosen for the supply rail. Extra supply voltage creates headroom that allows the LM4919 to reproduce peak in excess of 10mW without producing audible distortion. At this time, the designer must make sure that the power supply choice along with the output impedance does not violate the conditions explained in the Power Dissipation section. Once the power dissipation equations have been addressed, the required gain can be determined from Equation 2. OPTIMIZING CLICK AND POP REDUCTION PERFORMANCE The LM4919 contains circuitry that eliminates turn-on and shutdown transients ("clicks and pops"). For this discussion, turn-on refers to either applying the power supply voltage or when the micro-power shutdown mode is deactivated. As the VDD/2 voltage present at the BYPASS pin ramps to its final value, the LM4919's internal amplifiers are configured as unity gain buffers. An internal current source charges the capacitor connected between the BYPASS pin and GND in a controlled, linear manner. Ideally, the input and outputs track the voltage applied to the BYPASS pin. The gain of the internal amplifiers remains unity until the voltage on the bypass pin reaches VDD/2. As soon as the voltage on the bypass pin is stable, the device becomes fully operational and the am- (4) From Equation 4, the minimum AV is 1; use AV = 1. Since the desired input impedance is 20k, and with a AV gain of 1, a ratio of 1:1 results from Equation 1 for Rf to R. The values are chosen with Ri = 20k and Rf = 20k. The final design step is to address the bandwidth requirements which must be stated as a pair of -3dB frequency points. Five times away from a -3dB 15 200821 Version 2 Revision 3 10mWrms Print Date/Time: 2011/09/30 15:48:41 www.national.com LM4919 component combinations, consideration to component values must be used to maximize overall system quality. The LM4919 is unity-gain stable that gives the designer maximum system flexibility. The LM4919 should be used in low gain configurations to minimize THD+N values, and maximize the signal to noise ratio. Low gain configurations require large input signals to obtain a given output power. Input signals equal to or greater than 1Vrms are available from sources such as audio codecs. Very large values should not be used for the gain-setting resistors. Values for Ri and Rf should be less than 1MΩ. Please refer to the section, Audio Power Amplifier Design, for a more complete explanation of proper gain selection. Besides gain, one of the major considerations is the closed-loop bandwidth of the amplifier. To a large extent, the bandwidth is dictated by the choice of external components shown in Figures 2 and 3. The input coupling capacitor, Ci, forms a first order high pass filter that limits low frequency response. This value should be chosen based on needed frequency response and turn-on time. LM4919 point is 0.17dB down from passband response which is better than the required ± 0.25dB specified. The high frequency pole is determined by the product of the desired frequency pole, fH, and the differential gain, AV. With an AVV = 1 and fH = 100kHz, the resulting GBWP = 100kHz which is much smaller than the LM4919 GBWP of 3MHz. This example displays that if a designer has a need to design an amplifier with higher differential gain, the LM4919 can still be used without running into bandwidth limitations. fL = 100Hz/5 = 20Hz fH = 20kHz * 5 = 100kHz As stated in the External Components section, Ri in conjunction with Ci creates a Ci ≥ 1 / (2π * 20kΩ * 20Hz) = 0.397µF; use 0.39µF. www.national.com 16 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 LM4919 Physical Dimensions inches (millimeters) unless otherwise noted MSOP Package Order Number LM4919MM NS Package Number MUB10A 17 200821 Version 2 Revision 3 Print Date/Time: 2011/09/30 15:48:41 www.national.com LM4919 1.5V, Mono 85mW BTL Output, 14mW Stereo Headphone Audio Amplifier Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise® Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise® Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com www.national.com Tel: 1-800-272-9959 National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com 200821 Version 2 Revision 3 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com Print Date/Time: 2011/09/30 15:48:42 National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated