LM4925
www.ti.com
SNAS273 – FEBRUARY 2005
LM4925 Boomer™ Audio Power Amplifier Series 2 Cell, Single Ended Output, 40mW
Stereo Headphone Audio Amplifier
Check for Samples: LM4925
FEATURES
DESCRIPTION
•
•
•
The unity gain stable LM4925 is both a mono
differential output (for BTL operation) audio amplifier
and a Single Ended (SE) stereo headphone amplifier.
Operating on a single 3V supply, the mono-BTL
mode delivers 410mW into an 8Ω load at 1% THD+N.
In Single Ended stereo headphone mode, the
amplifier delivers 40mW per channel into a 16Ω load
at 1% THD+N.
1
23
•
•
•
•
•
BTL Mode for Mono Speaker
2-Cell 1.5V to 3.6V Battery Operation
Single Ended Headphone Operation with
Output Coupling Capacitors
Unity-Gain Stable
“Click and Pop” Suppression Circuitry for
Both Shutdown and Mute
Active Low Micro-Power Shutdown
Active-Low Mute Mode
Thermal Shutdown Protection Circuitry
APPLICATIONS
•
•
Portable Two-Cell Audio Products
Portable Two-Cell Electronic Devices
KEY SPECIFICATIONS
•
•
•
•
•
Mono-BTL Output Power
– (RL = 8Ω, VDD = 3.0V, THD+N = 1%),
410mW (Typ)
Single Ended Output Power Per Channel,
– (RL = 16Ω, VDD = 3.0V, THD+N = 1%),
40mW (Typ)
Micropower Shutdown Current, 0.1µA (Typ)
Supply Voltage Operating Range,
1.5V < VDD < 3.6V
PSRR 100Hz, VDD = 3V, BTL, 70dB (Typ)
With the LM4925 packaged in the VSSOP and SON
packages, the customer benefits include low profile
and small size. This package minimizes PCB area
and maximizes output power.
The LM4925 features circuitry that reduces output
transients (“clicks” and “pops”) during device turn-on
and turn-off, an externally controlled, low-power
consumption, active-low shutdown mode, and thermal
shutdown. Boomer audio power amplifiers are
designed specifically to use few external components
and provide high quality output power in a surface
mount package.
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Boomer is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005, Texas Instruments Incorporated
LM4925
SNAS273 – FEBRUARY 2005
www.ti.com
Typical Application
+
IN A
CBYPASS
Bias
Generator
IN B
SD
MUTE
VoA
Click-Pop
and
Mode Control
Logic
SE/BTL
+
VoB
Figure 1. Block Diagram
Connection Diagram
In A
SD
Mute
Bypass
IN B
1
10
2
9
3
8
4
7
5
6
VDD
VoA
SE/BTL
VoB
GND
Figure 2. VSSOP Package
Top View
See Package Number DGS for VSSOP
Figure 3. SON Package
Top View
See Package Number DSC0010A
2
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
LM4925
www.ti.com
SNAS273 – FEBRUARY 2005
Typical Connections
Rf
50k
Ci
Ri
Co
+
0.47 PF 20k
100 PF
Vin1
4.7 PF
Cbypass
Ci
+
16:
Bias
Generator
Ri
0.47 PF 20k
Click-Pop
and
Mode Control
Logic
Vin2
Co
+
100 PF
16:
Rf
50k
ShutDown and
Mute Controller
Figure 4. Typical Capacitive Couple (SE) Output Configuration Circuit
Rf
20k
Ci
Ri
0.47 PF
20k
Vin 1
Cbypass
4.7 PF
+
Bias
Generator
IN B
ShutDown and
Mute Controller
VoA
Click-Pop
and
Mode Control
Logic
VDD
8:
+
Rf
20k
20k
Figure 5. Typical BTL Speaker Configuration Circuit
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
3
LM4925
SNAS273 – FEBRUARY 2005
www.ti.com
Absolute Maximum Ratings (1) (2)
Supply Voltage
3.8V
−65°C to +150°C
Storage Temperature
−0.3V to VDD
+0.3V
Input Voltage
Power Dissipation (3)
Internally limited
ESD Susceptibility (4)
2000V
ESD Susceptibility (5)
200V
Junction Temperature
Solder Information
150°C
Small Outline Package Vapor
Phase (60sec)
215°C
Infrared (15 sec)
220°C
See AN-450 “Surface Mounting and their Effects on Product Reliablilty” for other methods of soldering surface mount devices.
θJA (typ) DGS
Thermal Resistance
(1)
(2)
(3)
(4)
(5)
θJA (typ) DSC0010A
175°C/W
73°C/W
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
The maximum power dissipation is dictated by TJMAX, θJA, and the ambient temperature TA and must be derated at elevated
temperatures. The maximum allowable power dissipation is PDMAX = (TJMAX − TA)/θJA. For the LM4925, TJMAX = 150°C. For the θJAs,
please see the Application Information section or the Absolute Maximum Ratings section.
Human body model, 100pF discharged through a 1.5kΩ resistor.
Machine model, 220pF–240pF discharged through all pins.
Operating Ratings
Temperature Range
4
TMIN ≤ TA ≤ TMAX
Supply Voltage
Submit Documentation Feedback
−40°C ≤ TA ≤ +85°C
1.5V ≤ VDD ≤ 3.6V
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
LM4925
www.ti.com
SNAS273 – FEBRUARY 2005
Electrical Characteristics VDD = 3.0V (1) (2)
The following specifications apply for the circuit shown in Figure 4 for Single Ended Outputs (AV = 2.5V) and Figure 5 for BTL
Outputs (AV-BTL = 2), unless otherwise specified. Limits apply for TA = 25°C.
Symbol
Parameter
Conditions
1.0
1.6
0.1
1
μA (max)
2
10
mV (max)
RL = 8Ω, BTL, Figure 5
THD+N = 1%, f = 1kHz
410
350
mW (min)
RL = 16Ω, Figure 4, SE per Channel,
THD+N = 1%, f = 1kHz
40
30
mW (min)
0.5
% (max)
Quiescent Power Supply Current
VIN = 0V, IO = 0A, RL = ∞
ISD
Shutdown Current
VSHUTDOWN = GND
VOS
Output Offset Voltage
Output Power (6)
THD+N
Total Harmonic Distortion + Noise
VNO
Output Voltage Noise
Crosstalk
PSRR
Power Supply Rejection Ratio
Units
(Limits)
Limit (4)
IDD
PO
LM4925
Typical (3)
(5)
RL = 8Ω, BTL, PO = 300mW,
Figure 5, f = 1kHz
0.1
RL = 16Ω, SE, PO = 20mW per channel,
Figure 4, f = 1kHz
0.05
mA (max)
20Hz to 20kHz, A-weighted,
Input Referred,
Single Ended Output, Figure 4
10
µVRMS
RL = 16Ω, Figure 4
58
dB
VRIPPLE = 200mVP-P sine wave
CBYPASS = 4.7µF, RL = 8Ω
f = 100Hz, BTL, Figure 5
70
dB
VRIPPLE = 200mVP-P sine wave
CBYPASS = 4.7µF, RL = 16Ω
f = 100Hz, SE, Figure 4
68
dB
VIH
Control Logic High
1.5V ≤ VDD ≤ 3.6V
0.7VDD
VIL
Control Logic Low
1.5V ≤ VDD ≤ 3.6V
0.3VDD
V (max)
1VPP Reference,
Ri = 20k, Rf = 50k
70
dB (min)
Mute
Attenuation
(1)
(2)
(3)
(4)
(5)
(6)
V (min)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
All voltages are measured with respect to the ground (GND) pins unless otherwise specified.
Typicals are measured at 25°C and represent the parametric norm.
Datasheet min/max specification limits are specified by design, test, or statistical analysis.
The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier.
Output power is measured at the device terminals.
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
5
LM4925
SNAS273 – FEBRUARY 2005
www.ti.com
Electrical Characteristics VDD = 1.8V
(1) (2)
The following specifications apply for the circuit shown in Figure 4 for Single Ended Outputs (AV = 2.5V) and Figure 5 for BTL
Outputs (AV-BTL = 2), unless otherwise specified. Limits apply for TA = 25°C.
Symbol
Parameter
Conditions
IDD
Quiescent Power Supply Current
VIN = 0V, IO = 0A, RL = ∞
ISD
Shutdown Current
VSHUTDOWN = GND
VOS
Output Offset Voltage
PO
Output Power
(6)
THD+N
Total Harmonic Distortion + Noise
VNO
Output Voltage Noise
Crosstalk
PSRR
Power Supply Rejection Ratio
(5)
LM4925
Typical (3)
Limit (4)
Units
(Limits)
0.9
1.6
0.05
1
mA (max)
μA (max)
2
10
mV (max)
RL = 8Ω, BTL, Figure 5,
THD+N = 1%, f = 1kHz
120
90
mW (min)
RL = 16Ω, Figure 4, SE per Channel,
THD+N = 1%, f = 1kHz
10
7
mW (min)
0.5
% (max)
RL = 8Ω, BTL, PO = 50mW,
Figure 5, f = 1kHz
0.15
RL = 16Ω, SE, PO = 5mW per channel,
Figure 4, f = 1kHz
0.1
20Hz to 20kHz, A-weighted,
Input Referred,
Single Ended Output, Figure 4
10
µVRMS
RL = 16Ω, Figure 4
58
dB
VRIPPLE = 200mVP-P sine wave
CBYPASS = 4.7µF, RL = 8Ω
f = 100Hz, BTL, Figure 5
70
dB
VRIPPLE = 200mVP-P sine wave
CBYPASS = 4.7µF, RL = 16Ω
f = 100Hz, SE, Figure 4
68
dB
VIH
Control Logic High
1.5V ≤ VDD ≤ 3.6V
0.7VDD
VIL
Control Logic Low
1.5V ≤ VDD ≤ 3.6V
0.3VDD
V (max)
1VPP Reference,
Ri = 20k, Rf = 50k
70
dB (min)
Mute
Attenuation
(1)
(2)
(3)
(4)
(5)
(6)
6
V (min)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
All voltages are measured with respect to the ground (GND) pins unless otherwise specified.
Typicals are measured at 25°C and represent the parametric norm.
Datasheet min/max specification limits are specified by design, test, or statistical analysis.
The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier.
Output power is measured at the device terminals.
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
LM4925
www.ti.com
SNAS273 – FEBRUARY 2005
Typical Performance Characteristics
THD+N vs Frequency
VDD = 3V, SE, RL = 16Ω
PO = 20mW per channel
10
1
1
THD + N (%)
THD + N (%)
10
THD+N vs Frequency
VDD = 1.8V, SE, RL = 16Ω
PO = 5mW per channel
0.1
0.1
0.01
0.01
100
1k
10k
100
FREQUENCY (Hz)
10
Figure 7.
THD+N vs Frequency
VDD = 1.8V, BTL, RL = 8Ω
PO = 50mW
THD+N vs Frequency
VDD = 3V, BTL, RL = 8Ω
PO = 300mW
10
1
THD + N (%)
THD + N (%)
10k
Figure 6.
1
0.1
0.1
0.01
0.01
0.001
0.001
100
1k
10k
100
FREQUENCY (Hz)
1k
10k
FREQUENCY (Hz)
Figure 8.
Figure 9.
THD+N vs Output Power
VDD = 1.8V, SE, RL = 16Ω
f = 1kHz, Both channels
THD+N vs Output Power
VDD = 3V, SE, RL = 16Ω
f = 1kHz, Both channels
10
10
1
1
THD + N (%)
THD + N (%)
1k
FREQUENCY (Hz)
0.1
0.1
0.01
0.01
1
2
3
5
7 10
1
20 30 40 60
2
3
5
7 10
20 30 40 60
OUTPUT POWER (mW)
OUTPUT POWER (mW)
Figure 10.
Figure 11.
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
7
LM4925
SNAS273 – FEBRUARY 2005
www.ti.com
Typical Performance Characteristics (continued)
THD+N vs Output Power
VDD = 3V, BTL, RL = 8Ω
f = 1kHz
10
10
1
1
THD + N (%)
THD + N (%)
THD+N vs Output Power
VDD = 1.8V, BTL, RL = 8Ω
f = 1kHz
0.1
0.01
0.1
0.01
1
10
100
1
10
OUTPUT POWER (mW)
OUTPUT POWER (mW)
Figure 12.
Figure 13.
Output Noise vs Frequency
Output Power vs Supply Voltage
RL = 8Ω, BTL, f = 1kHz
800
700
50
OUTPUT POWER (mW)
OUTPUT NOISE LEVEL (PV)
100
20
10
5
2
600
500
THD+N = 10%
400
300
200
THD+N = 1%
100
1
0
2k 4k 6k 8k 10k 12k 14k 16k 18k 20k
1.6
2.0
FREQUENCY (Hz)
2.4
2.8
3.2
3.6
SUPPLY VOLTAGE (V)
Figure 14.
Figure 15.
Output Power vs Supply Voltage
RL = 16Ω, SE, f = 1kHz
Output Power vs Load Resistance
VDD = 1.8V, BTL, f = 1kHz
200
80
POWER DISSIPATION (mW)
70
OUTPUT POWER (mW)
100
60
50
THD+N = 10%
40
30
20
THD+N = 1%
150
THD+N = 10%
100
THD+N = 1%
50
10
0
0
1.6
2.0
2.4
2.8
3.2
16
3.6
64
80
96
112 128
LOAD RESISTANCE (:)
SUPPLY VOLTAGE (V)
Figure 16.
8
32 48
Figure 17.
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
LM4925
www.ti.com
SNAS273 – FEBRUARY 2005
Typical Performance Characteristics (continued)
Output Power vs Load Resistance
VDD = 3V, BTL, f = 1kHz
14
600
12
500
POWER DISSIPATION (mW)
POWER DISSIPATION (mW)
Output Power vs Load Resistance
VDD = 1.8V, SE, f = 1kHz
10
THD+N = 10%
8
6
4
THD+N = 1%
2
0
THD+N = 10%
400
300
200
THD+N = 1%
100
0
16
32
48
64
80
96
112 128
16
32
48
64
80
96 112 128 144
LOAD RESISTANCE (:)
Figure 18.
Figure 19.
Output Power vs Load Resistance
VDD = 3V, SE, f = 1kHz
Output Power vs Supply Voltage
RL = 8Ω, BTL, f = 1kHz
60
800
50
700
THD+N = 10%
OUTPUT POWER (mW)
POWER DISSIPATION (mW)
LOAD RESISTANCE (:)
THD+N = 10%
40
30
THD+N = 1%
20
500
400
300
200
THD+N = 1%
10
0
600
100
16
32
48
64
80
96
0
112 128
1.6
2.0
LOAD RESISTANCE (:)
2.4
2.8
3.2
3.6
SUPPLY VOLTAGE (V)
Figure 20.
Figure 21.
Power Dissipation vs Output Power
VDD = 1.8V, RL = 8Ω, BTL, f = 1kHz
Power Dissipation vs Output Power
VDD = 1.8V, RL = 16Ω, SE, f = 1kHz
90
250
POWER DISSIPATION (mW)
POWER DISSIPATION (mW)
80
200
150
100
50
70
60
50
40
30
20
10
0
0
0
20
40
60
80
100 120
140
0
2
4
6
8
OUTPUT POWER (mW)
OUTPUT POWER (mW)
Figure 22.
Figure 23.
10
12
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
9
LM4925
SNAS273 – FEBRUARY 2005
www.ti.com
Typical Performance Characteristics (continued)
Power Dissipation vs Output Power
VDD = 3V, RL = 8Ω, BTL, f = 1kHz
Power Dissipation vs Output Power
VDD = 3V, RL = 16Ω, SE, f = 1kHz
120
POWER DISSIPATION (mW)
POWER DISSIPATION (mW)
250
200
150
100
50
0
100
80
60
40
20
0
0
100
200
300
400
0
500
12 16 20 24 28 32 36 40
Figure 25.
Power Supply Rejection vs Frequency
VDD = 1.8V, RL = 8Ω, BTL
VRIPPLE = 200mVp-p, AV-BTL = 2V/V
Power Supply Rejection vs Frequency
VDD = 1.8V, RL = 16Ω, SE
VRIPPLE = 200mVp-p, AV = 2.5V/V
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
20
200
2k
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
20
20k
200
2k
20k
FREQUENCY (Hz)
Figure 26.
Figure 27.
Power Supply Rejection vs Frequency
VDD = 3V, RL = 8Ω, BTL
VRIPPLE = 200mVp-p, AV-BTL = 2V/V
Power Supply Rejection vs Frequency
VDD = 3V, RL = 16Ω, SE
VRIPPLE = 200mVp-p, AV = 2.5V/V
0
POWER SUPPLY REJECTION RATIO (dB)
POWER SUPPLY REJECTION RATIO (dB)
8
OUTPUT POWER (mW)
FREQUENCY (Hz)
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
20
200
2k
20k
FREQUENCY (Hz)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
20
200
2k
20k
FREQUENCY (Hz)
Figure 28.
10
4
Figure 24.
POWER SUPPLY REJECTION RATIO (dB)
POWER SUPPLY REJECTION RATIO (dB)
OUTPUT POWER (mW)
Figure 29.
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
LM4925
www.ti.com
SNAS273 – FEBRUARY 2005
APPLICATION INFORMATION
BRIDGE (BTL) CONFIGURATION EXPLANATION
The LM4925 is a stereo audio power amplifier capable of operating in bridged (BTL) mode. As shown in
Figure 5, the LM4925 has two internal operational amplifiers. The first amplifier’s gain is externally configurable,
while the second amplifier should be externally fixed in a unity-gain, inverting configuration. The closed-loop gain
of the first amplifier is set by selecting the ratio of Rf to Ri while the second amplifier’s gain is fixed by the two
external 20kΩ resistors. Figure 5 shows that the output of amplifier one serves as the input to amplifier two which
results in both amplifiers producing signals identical in magnitude, but out of phase by 180°. Consequently, the
differential gain for the IC is
AVD = 2 * (Rf / Ri)
(1)
By driving the load differentially through outputs VoA and VoB, an amplifier configuration commonly referred to
as “bridged mode” is established. Bridged mode operation is different from the classical single-ended amplifier
configuration where one side of the load is connected to ground. A bridge amplifier design has a few distinct
advantages over the single-ended configuration, as it provides differential drive to the load, thus doubling output
swing for a specified supply voltage. Four times the output power is possible as compared to a single-ended
amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not
current limited or clipped. In order to choose an amplifier’s closed-loop gain without causing excessive clipping,
please refer to the AUDIO POWER AMPLIFIER DESIGN section.
A bridge configuration, such as the one used in LM4925, also creates a second advantage over single-ended
amplifiers. Since the differential outputs, VoA and VoB, are biased at half-supply, no net DC voltage exists
across the load. This eliminates the need for an output coupling capacitor which is required in a single supply,
single-ended amplifier configuration.
MODE SELECT DETAIL
The LM4925 can be configured for either single ended (see Figure 4) or BTL mode (see Figure 5). When the
SE/BTL pin has a logic high (VDD) applied to it, the LM4925 is in BTL mode. If a logic low (GND) is applied to
SE/BTL, the LM4925 operates in single-ended mode. The slew rate of VDD must be greater than 2.5V/ms to
ensure reliable Power on reset (POR). The circuit shown in Figure 30 presents an applications solution to the
problem of using different supply voltages with different turn-on times in a system with the LM4925. This circuit
shows the LM4925 with a 25-50kΩ. Pull-up resistor connected from the shutdown pin to VDD. The shutdown pin
of the LM4925 is also being driven by an open drain output of an external microcontroller on a separate supply.
This circuit ensures that shutdown is disabled when powering up the LM4925 by either allowing shutdown to be
high before the LM4925 powers on (the microcontroller powers up first) or allows shutdown to ramp up with VDD
(the LM4925 powers up first). This will ensure the LM4925 powers up properly and enters the correct mode of
operation (BTL or SE). Please note that the SE/BTL pin should be tied to GND for single-ended (SE) mode, and
to Vdd for BTL mode.
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
11
LM4925
SNAS273 – FEBRUARY 2005
www.ti.com
3.3V
20k
5V
25k to 50k
10
1
Controller
0.47 PF
IN A
VDD
VoA
9
20k
MOSFET N
100 PF
2
SPEAKER
SD
LM4925
3
4
5
0.47 PF
MUTE
SE/BT
8
BYP
IN B
20k
4.7 mF
GND
6
VoB
7
100 PF
SPEAKER
20k
Figure 30. Recommended Circuit for Different Supply Turn-On Timing
POWER DISSIPATION
Power dissipation is a major concern when designing a successful amplifier, whether the amplifier is bridged
(BTL) or single-ended. A direct consequence of the increased power delivered to the load by a bridge amplifier is
an increase in internal power dissipation. Since the LM4925 has two operational amplifiers in one package, the
maximum internal power dissipation in BTL mode is 4 times that of a single-ended amplifier. The maximum
power dissipation for a given application can be derived from the power dissipation graphs or from Equation 2.
PDMAX = 4 * (VDD) 2 / (2π2RL)
(2)
When operating in single ended mode, Equation 3 states the maximum power dissipation point for a singleended amplifier operating at a given supply voltage and driving a specified output load.
PDMAX = (VDD) 2 / (2π2RL)
(3)
Since the LM4925 has two operational amplifiers in one package, the maximum internal power dissipation point
is twice that of the number that results from Equation 3.
The maximum power dissipation point obtained from either Equation 2 or Equation 3 must not be greater than
the power dissipation that results from Equation 4:
PDMAX = (TJMAX - TA) / θJA
(4)
For package DGS, θJA = 175°C/W. TJMAX = 150°C for the LM4925. Depending on the ambient temperature, TA,
of the system surroundings, Equation 4 can be used to find the maximum internal power dissipation supported by
the IC packaging. If the result of Equation 2 or Equation 3 is greater than that of Equation 4, then either the
supply voltage must be decreased, the load impedance increased or TA reduced. For the typical application of a
3.0V power supply, with an 16Ω load, the maximum ambient temperature possible without violating the maximum
junction temperature is approximately 129°C provided that device operation is around the maximum power
dissipation point. Thus, for typical applications, power dissipation is not an issue. Power dissipation is a function
of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient
temperature may be increased accordingly. Refer to the Typical Performance Characteristics curves for power
dissipation information for lower output powers.
POWER SUPPLY BYPASSING
As with any amplifier, proper supply bypassing is important for low noise performance and high power supply
rejection. The capacitor location on the power supply pins should be as close to the device as possible. Typical
applications employ a battery (or 3.0V regulator) with 10μF tantalum or electrolytic capacitor and a ceramic
bypass capacitor that aid in supply stability. This does not eliminate the need for bypassing the supply nodes of
the LM4925. A bypass capacitor value in the range of 0.1μF to 4.7μF is recommended.
12
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
LM4925
www.ti.com
SNAS273 – FEBRUARY 2005
MICRO POWER SHUTDOWN
The voltage applied to the SHUTDOWN pin controls the LM4925’s shutdown function. Activate micro-power
shutdown by applying a logic-low voltage to the SHUTDOWN pin. When active, the LM4925’s micro-power
shutdown feature turns off the amplifier’s bias circuitry, reducing the supply current. A voltage that is higher than
ground may increase the shutdown current. There are a few ways to control the micro-power shutdown. These
include using a single-pole, single-throw switch, a microprocessor, or a microcontroller. When using a switch,
connect an external 100kΩ pull-up resistor between the SHUTDOWN pin and VDD. Connect the switch between
the SHUTDOWN pin and ground. Select normal amplifier operation by opening the switch. Closing the switch
connects the SHUTDOWN pin to ground, activating micro-power shutdown. The switch and resistor guarantee
that the SHUTDOWN pin will not float. This prevents unwanted state changes. In a system with a microprocessor
or microcontroller, use a digital output to apply the control voltage to the SHUTDOWN pin. Driving the
SHUTDOWN pin with active circuitry eliminates the pull-up resistor. Shutdown enable/disable times are
controlled by a combination of Cbypass and VDD. Larger values of Cbypass results in longer turn on/off times from
Shutdown. Longer shutdown times also improve the LM4925’s resistance to click and pop upon entering or
returning from shutdown. For a 3.0V supply and Cbypass = 4.7μF, the LM4925 requires about 2 seconds to enter
or return from shutdown. This longer shutdown time enables the LM4925 to have virtually zero pop and click
transients upon entering or release from shutdown. Smaller values of Cbypass will decrease turn-on time, but at
the cost of increased pop and click and reduced PSRR. When the LM4925 is in shutdown, the outputs become
very low impedance (less than 5Ω to GND).
MUTE
The LM4925 also features a mute function that enables extremely fast turn-on/turn-off with a minimum of output
pop and click. The mute function leaves the outputs at their bias level, thus resulting in higher power
consumption than shutdown mode, but also provides much faster turn on/off times. Providing a logic low signal
on the MUTE pin enables mute mode. Threshold voltages and activation techniques match those given for the
shutdown function as well.
PROPER SELECTION OF EXTERNAL COMPONENTS
Proper selection of external components in applications using integrated power amplifiers is critical to optimize
device and system performance. While the LM4925 is tolerant of external component combinations,
consideration to component values must be used to maximize overall system quality. The LM4925 is unity-gain
stable that gives the designer maximum system flexibility. The LM4925 should be used in low gain configurations
to minimize THD+N values, and maximize the signal to noise ratio. Low gain configurations require large input
signals to obtain a given output power. Input signals equal to or greater than 1Vrms are available from sources
such as audio codecs. Very large values should not be used for the gain-setting resistors. Values for Ri and Rf
should be less than 1MΩ. Please refer to the section, AUDIO POWER AMPLIFIER DESIGN, for a more
complete explanation of proper gain selection. Besides gain, one of the major considerations is the closed-loop
bandwidth of the amplifier. To a large extent, the bandwidth is dictated by the choice of external components
shown in Figure 4 and Figure 5. The input coupling capacitor, Ci, forms a first order high pass filter that limits low
frequency response. This value should be chosen based on needed frequency response and turn-on time.
SELECTION OF INPUT CAPACITOR SIZE
Amplifying the lowest audio frequencies requires a high value input coupling capacitor, Ci. A high value capacitor
can be expensive and may compromise space efficiency in portable designs. In many cases, however, the
headphones used in portable systems have little ability to reproduce signals below 60Hz. Applications using
headphones with this limited frequency response reap little improvement by using a high value input capacitor. In
addition to system cost and size, turn on time is affected by the size of the input coupling capacitor Ci. A larger
input coupling capacitor requires more charge to reach its quiescent DC voltage. This charge comes from the
output via the feedback. Thus, by minimizing the capacitor size based on necessary low frequency response,
turn-on time can be minimized. A small value of Ci (in the range of 0.1μF to 0.47μF), is recommended.
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
13
LM4925
SNAS273 – FEBRUARY 2005
www.ti.com
AUDIO POWER AMPLIFIER DESIGN
A 25mW/32Ω Audio Amplifier
Given:
Power Output
10mWrms
Load Impedance
16Ω
Input Level
0.4Vrms
Input Impedance
20kΩ
A designer must first choose a mode of operation (SE or BTL) and determine the minimum supply rail to obtain
the specified output power. By extrapolating from the Output Power vs. Supply Voltage graphs in the Typical
Performance Characteristics section, the supply rail can be easily found. 3.0V is a standard voltage in most
applications, it is chosen for the supply rail. Extra supply voltage creates headroom that allows the LM4925 to
reproduce peak in excess of 10mW without producing audible distortion. At this time, the designer must make
sure that the power supply choice along with the output impedance does not violate the conditions explained in
the POWER DISSIPATION section. Once the power dissipation equations have been addressed, the required
gain can be determined from Equation 3.
(5)
From Equation 5, the minimum AV is 1; use AV = 1. Since the desired input impedance is 20k, and with a AV gain
of 1, a ratio of 1:1 results from Equation 2 for Rf to R. The values are chosen with Ri = 20k and Rf = 20k. The
final design step is to address the bandwidth requirements which must be stated as a pair of -3dB frequency
points. Five times away from a -3dB point is 0.17dB down from passband response which is better than the
required ± 0.25dB specified.
fL = 100Hz/5 = 20Hz
fH = 20kHz * 5 = 100kHz
As stated in the PROPER SELECTION OF EXTERNAL COMPONENTS section, Ri in conjunction with Ci
creates a
Ci ≥ 1 / (2π * 20kΩ * 20Hz) = 0.397µF; use 0.39µF.
The high frequency pole is determined by the product of the desired frequency pole, fH, and the differential gain,
AV. With an AVV = 1 and fH = 100kHz, the resulting GBWP = 100kHz which is much smaller than the
LM4925GBWP of 3MHz. This example displays that if a designer has a need to design an amplifier with higher
differential gain, the LM4925can still be used without running into bandwidth limitations.
14
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
LM4925
www.ti.com
SNAS273 – FEBRUARY 2005
LM4925 BOARD ARTWORK
Figure 31. Composite View
Figure 32. Silk Screen
Figure 33. Top Layer
Figure 34. Bottom Layer
Submit Documentation Feedback
Copyright © 2005, Texas Instruments Incorporated
Product Folder Links: LM4925
15
PACKAGE OPTION ADDENDUM
www.ti.com
6-Mar-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LM4925MM/NOPB
ACTIVE
VSSOP
DGS
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
GB8
LM4925SD/NOPB
ACTIVE
WSON
DSC
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
L4925
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Nov-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM4925MM/NOPB
VSSOP
DGS
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM4925SD/NOPB
SON
DSC
10
1000
178.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Nov-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM4925MM/NOPB
VSSOP
DGS
10
1000
203.0
190.0
41.0
LM4925SD/NOPB
SON
DSC
10
1000
203.0
190.0
41.0
Pack Materials-Page 2
MECHANICAL DATA
DSC0010A
SDA10A (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM4925MM LM4925MMX LM4925MMX/NOPB LM4925SD LM4925SDX LM4925SDX/NOPB