LM4F232H5BBFIGR

TE X AS INS TRUM E NTS - ADVANCE INFO R MAT ION ® Stellaris LM4F232H5BB Microcontroller D ATA SHE E T D S -LM4F 232H5 B B - 11 0 0 3 C o p yri g h t © 2 0 07-2011 Te xa s In stru me n ts In co rporated Copyright Copyright © 2007-2011 Texas Instruments Incorporated All rights reserved. Stellaris and StellarisWare® are registered trademarks of Texas Instruments Incorporated. ARM and Thumb are registered trademarks and Cortex is a trademark of ARM Limited. Other names and brands may be claimed as the property of others. ADVANCE INFORMATION concerns new products in the sampling or preproduction phase of development. Characteristic data and other specifications are subject to change without notice. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Texas Instruments Incorporated 108 Wild Basin, Suite 350 Austin, TX 78746 http://www.ti.com/stellaris http://www-k.ext.ti.com/sc/technical-support/product-information-centers.htm 2 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table of Contents Revision History ............................................................................................................................. 39 About This Document .................................................................................................................... 40 Audience .............................................................................................................................................. About This Manual ................................................................................................................................ Related Documents ............................................................................................................................... Documentation Conventions .................................................................................................................. 40 40 40 41 1 Architectural Overview .......................................................................................... 43 1.1 1.2 1.3 1.3.1 1.3.2 1.3.3 1.3.4 1.3.5 1.3.6 1.3.7 1.3.8 1.4 Stellaris LM4F Series Overview ..................................................................................... 43 LM4F232H5BB Microcontroller Overview ........................................................................ 46 LM4F232H5BB Microcontroller Features ........................................................................ 49 ARM Cortex-M4F Processor Core .................................................................................. 49 On-Chip Memory ........................................................................................................... 51 Serial Communications Peripherals ................................................................................ 53 System Integration ........................................................................................................ 57 Advanced Motion Control ............................................................................................... 63 Analog .......................................................................................................................... 65 JTAG and ARM Serial Wire Debug ................................................................................ 67 Packaging and Temperature .......................................................................................... 68 Hardware Details .......................................................................................................... 68 2 The Cortex-M4F Processor ................................................................................... 69 2.1 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.4 2.4.1 2.4.2 2.4.3 2.4.4 2.4.5 2.4.6 2.4.7 2.5 2.5.1 2.5.2 2.5.3 Block Diagram .............................................................................................................. 70 Overview ...................................................................................................................... 71 System-Level Interface .................................................................................................. 71 Integrated Configurable Debug ...................................................................................... 71 Trace Port Interface Unit (TPIU) ..................................................................................... 72 Cortex-M4F System Component Details ......................................................................... 72 Programming Model ...................................................................................................... 73 Processor Mode and Privilege Levels for Software Execution ........................................... 73 Stacks .......................................................................................................................... 74 Register Map ................................................................................................................ 74 Register Descriptions .................................................................................................... 76 Exceptions and Interrupts .............................................................................................. 92 Data Types ................................................................................................................... 92 Memory Model .............................................................................................................. 92 Memory Regions, Types and Attributes ........................................................................... 95 Memory System Ordering of Memory Accesses .............................................................. 95 Behavior of Memory Accesses ....................................................................................... 95 Software Ordering of Memory Accesses ......................................................................... 96 Bit-Banding ................................................................................................................... 97 Data Storage .............................................................................................................. 100 Synchronization Primitives ........................................................................................... 100 Exception Model ......................................................................................................... 101 Exception States ......................................................................................................... 102 Exception Types .......................................................................................................... 102 Exception Handlers ..................................................................................................... 107 November 08, 2011 3 Texas Instruments-Advance Information Table of Contents 2.5.4 2.5.5 2.5.6 2.5.7 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.7 2.7.1 2.7.2 2.7.3 2.8 Vector Table ................................................................................................................ Exception Priorities ...................................................................................................... Interrupt Priority Grouping ............................................................................................ Exception Entry and Return ......................................................................................... Fault Handling ............................................................................................................. Fault Types ................................................................................................................. Fault Escalation and Hard Faults .................................................................................. Fault Status Registers and Fault Address Registers ...................................................... Lockup ....................................................................................................................... Power Management .................................................................................................... Entering Sleep Modes ................................................................................................. Wake Up from Sleep Mode .......................................................................................... The Wake-Up Interrupt Controller ................................................................................. Instruction Set Summary .............................................................................................. 107 108 109 109 112 113 113 114 114 115 115 115 116 116 3 Cortex-M4 Peripherals ......................................................................................... 124 3.1 3.1.1 3.1.2 3.1.3 3.1.4 3.1.5 3.2 3.3 3.4 3.5 3.6 3.7 Functional Description ................................................................................................. 124 System Timer (SysTick) ............................................................................................... 125 Nested Vectored Interrupt Controller (NVIC) .................................................................. 126 System Control Block (SCB) ........................................................................................ 127 Memory Protection Unit (MPU) ..................................................................................... 127 Floating-Point Unit (FPU) ............................................................................................. 132 Register Map .............................................................................................................. 136 System Timer (SysTick) Register Descriptions .............................................................. 139 NVIC Register Descriptions .......................................................................................... 143 System Control Block (SCB) Register Descriptions ........................................................ 158 Memory Protection Unit (MPU) Register Descriptions .................................................... 187 Floating-Point Unit (FPU) Register Descriptions ............................................................ 196 4 JTAG Interface ...................................................................................................... 202 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.4 4.5 4.5.1 4.5.2 Block Diagram ............................................................................................................ Signal Description ....................................................................................................... Functional Description ................................................................................................. JTAG Interface Pins ..................................................................................................... JTAG TAP Controller ................................................................................................... Shift Registers ............................................................................................................ Operational Considerations .......................................................................................... Initialization and Configuration ..................................................................................... Register Descriptions .................................................................................................. Instruction Register (IR) ............................................................................................... Data Registers ............................................................................................................ 203 203 204 204 205 206 206 209 209 209 211 5 System Control ..................................................................................................... 214 5.1 5.2 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 Signal Description ....................................................................................................... Functional Description ................................................................................................. Device Identification .................................................................................................... Reset Control .............................................................................................................. Non-Maskable Interrupt ............................................................................................... Power Control ............................................................................................................. Clock Control .............................................................................................................. System Control ........................................................................................................... 4 214 214 214 215 219 220 221 228 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 5.3 5.4 5.5 Initialization and Configuration ..................................................................................... 230 Register Map .............................................................................................................. 231 Register Descriptions .................................................................................................. 236 6 System Exception Module ................................................................................... 514 6.1 6.2 6.3 Functional Description ................................................................................................. 514 Register Map .............................................................................................................. 514 Register Descriptions .................................................................................................. 514 7 Hibernation Module .............................................................................................. 522 7.1 7.2 7.3 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 7.3.6 7.3.7 7.3.8 7.3.9 7.3.10 7.3.11 7.3.12 7.4 7.4.1 7.4.2 7.4.3 7.4.4 7.4.5 7.5 7.6 Block Diagram ............................................................................................................ Signal Description ....................................................................................................... Functional Description ................................................................................................. Register Access Timing ............................................................................................... Hibernation Clock Source ............................................................................................ System Implementation ............................................................................................... Battery Management ................................................................................................... Real-Time Clock .......................................................................................................... Battery-Backed Memory .............................................................................................. Power Control Using HIB ............................................................................................. Power Control Using VDD3ON Mode ........................................................................... Initiating Hibernate ...................................................................................................... Waking from Hibernate ................................................................................................ Arbitrary Power Removal ............................................................................................. Interrupts and Status ................................................................................................... Initialization and Configuration ..................................................................................... Initialization ................................................................................................................. RTC Match Functionality (No Hibernation) .................................................................... RTC Match/Wake-Up from Hibernation ......................................................................... External Wake-Up from Hibernation .............................................................................. RTC or External Wake-Up from Hibernation .................................................................. Register Map .............................................................................................................. Register Descriptions .................................................................................................. 523 523 524 525 525 526 527 528 529 529 530 530 530 530 531 531 531 532 532 533 533 533 534 8 Internal Memory ................................................................................................... 552 8.1 8.2 8.2.1 8.2.2 8.2.3 8.2.4 8.3 8.4 8.5 8.6 Block Diagram ............................................................................................................ 552 Functional Description ................................................................................................. 553 SRAM ........................................................................................................................ 553 ROM .......................................................................................................................... 554 Flash Memory ............................................................................................................. 556 EEPROM .................................................................................................................... 560 Register Map .............................................................................................................. 565 Flash Memory Register Descriptions (Flash Control Offset) ............................................ 567 EEPROM Register Descriptions (EEPROM Offset) ........................................................ 585 Memory Register Descriptions (System Control Offset) .................................................. 601 9 Micro Direct Memory Access (μDMA) ................................................................ 610 9.1 9.2 9.2.1 9.2.2 Block Diagram ............................................................................................................ Functional Description ................................................................................................. Channel Assignments .................................................................................................. Priority ........................................................................................................................ November 08, 2011 611 611 612 613 5 Texas Instruments-Advance Information Table of Contents 9.2.3 9.2.4 9.2.5 9.2.6 9.2.7 9.2.8 9.2.9 9.2.10 9.3 9.3.1 9.3.2 9.3.3 9.3.4 9.3.5 9.4 9.5 9.6 Arbitration Size ............................................................................................................ 613 Request Types ............................................................................................................ 614 Channel Configuration ................................................................................................. 614 Transfer Modes ........................................................................................................... 616 Transfer Size and Increment ........................................................................................ 624 Peripheral Interface ..................................................................................................... 624 Software Request ........................................................................................................ 624 Interrupts and Errors .................................................................................................... 625 Initialization and Configuration ..................................................................................... 625 Module Initialization ..................................................................................................... 625 Configuring a Memory-to-Memory Transfer ................................................................... 626 Configuring a Peripheral for Simple Transmit ................................................................ 627 Configuring a Peripheral for Ping-Pong Receive ............................................................ 629 Configuring Channel Assignments ................................................................................ 631 Register Map .............................................................................................................. 631 μDMA Channel Control Structure ................................................................................. 633 μDMA Register Descriptions ........................................................................................ 640 10 General-Purpose Input/Outputs (GPIOs) ........................................................... 674 10.1 10.2 10.2.1 10.2.2 10.2.3 10.2.4 10.2.5 10.2.6 10.3 10.4 10.5 Signal Description ....................................................................................................... 675 Functional Description ................................................................................................. 678 Data Control ............................................................................................................... 680 Interrupt Control .......................................................................................................... 681 Mode Control .............................................................................................................. 682 Commit Control ........................................................................................................... 683 Pad Control ................................................................................................................. 683 Identification ............................................................................................................... 683 Initialization and Configuration ..................................................................................... 683 Register Map .............................................................................................................. 684 Register Descriptions .................................................................................................. 687 11 General-Purpose Timers ...................................................................................... 734 11.1 11.2 11.3 11.3.1 11.3.2 11.3.3 11.3.4 11.3.5 11.3.6 11.3.7 11.4 11.4.1 11.4.2 11.4.3 11.4.4 11.4.5 11.5 11.6 Block Diagram ............................................................................................................ 735 Signal Description ....................................................................................................... 736 Functional Description ................................................................................................. 738 GPTM Reset Conditions .............................................................................................. 739 Timer Modes ............................................................................................................... 740 Wait-for-Trigger Mode .................................................................................................. 749 Synchronizing GP Timer Blocks ................................................................................... 750 DMA Operation ........................................................................................................... 751 Accessing Concatenated 16/32-Bit GPTM Register Values ............................................ 751 Accessing Concatenated 32/64-Bit Wide GPTM Register Values .................................... 751 Initialization and Configuration ..................................................................................... 753 One-Shot/Periodic Timer Mode .................................................................................... 753 Real-Time Clock (RTC) Mode ...................................................................................... 754 Input Edge-Count Mode ............................................................................................... 754 Input Edge Timing Mode .............................................................................................. 755 PWM Mode ................................................................................................................. 755 Register Map .............................................................................................................. 756 Register Descriptions .................................................................................................. 757 6 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 12 Watchdog Timers ................................................................................................. 804 12.1 12.2 12.2.1 12.3 12.4 12.5 Block Diagram ............................................................................................................ Functional Description ................................................................................................. Register Access Timing ............................................................................................... Initialization and Configuration ..................................................................................... Register Map .............................................................................................................. Register Descriptions .................................................................................................. 805 805 806 806 806 807 13 Analog-to-Digital Converter (ADC) ..................................................................... 829 13.1 13.2 13.3 13.3.1 13.3.2 13.3.3 13.3.4 13.3.5 13.3.6 13.3.7 13.4 13.4.1 13.4.2 13.5 13.6 Block Diagram ............................................................................................................ 830 Signal Description ....................................................................................................... 831 Functional Description ................................................................................................. 832 Sample Sequencers .................................................................................................... 833 Module Control ............................................................................................................ 833 Hardware Sample Averaging Circuit ............................................................................. 836 Analog-to-Digital Converter .......................................................................................... 837 Differential Sampling ................................................................................................... 839 Internal Temperature Sensor ........................................................................................ 841 Digital Comparator Unit ............................................................................................... 842 Initialization and Configuration ..................................................................................... 846 Module Initialization ..................................................................................................... 846 Sample Sequencer Configuration ................................................................................. 847 Register Map .............................................................................................................. 847 Register Descriptions .................................................................................................. 849 14 Universal Asynchronous Receivers/Transmitters (UARTs) ............................. 918 14.1 Block Diagram ............................................................................................................ 14.2 Signal Description ....................................................................................................... 14.3 Functional Description ................................................................................................. 14.3.1 Transmit/Receive Logic ............................................................................................... 14.3.2 Baud-Rate Generation ................................................................................................. 14.3.3 Data Transmission ...................................................................................................... 14.3.4 Serial IR (SIR) ............................................................................................................. 14.3.5 ISO 7816 Support ....................................................................................................... 14.3.6 Modem Handshake Support ......................................................................................... 14.3.7 LIN Support ................................................................................................................ 14.3.8 9-Bit UART Mode ........................................................................................................ 14.3.9 FIFO Operation ........................................................................................................... 14.3.10 Interrupts .................................................................................................................... 14.3.11 Loopback Operation .................................................................................................... 14.3.12 DMA Operation ........................................................................................................... 14.4 Initialization and Configuration ..................................................................................... 14.5 Register Map .............................................................................................................. 14.6 Register Descriptions .................................................................................................. 919 919 920 921 921 922 922 923 924 925 926 927 927 928 928 929 930 931 15 Synchronous Serial Interface (SSI) .................................................................... 985 15.1 15.2 15.3 15.3.1 15.3.2 Block Diagram ............................................................................................................ Signal Description ....................................................................................................... Functional Description ................................................................................................. Bit Rate Generation ..................................................................................................... FIFO Operation ........................................................................................................... November 08, 2011 986 986 987 988 988 7 Texas Instruments-Advance Information Table of Contents 15.3.3 15.3.4 15.3.5 15.4 15.5 15.6 Interrupts .................................................................................................................... Frame Formats ........................................................................................................... DMA Operation ........................................................................................................... Initialization and Configuration ..................................................................................... Register Map .............................................................................................................. Register Descriptions .................................................................................................. 988 989 996 997 998 999 16 Inter-Integrated Circuit (I2C) Interface .............................................................. 1028 16.1 16.2 16.3 16.3.1 16.3.2 16.3.3 16.3.4 16.3.5 16.4 16.5 16.6 16.7 16.8 Block Diagram ........................................................................................................... 1029 Signal Description ..................................................................................................... 1029 Functional Description ............................................................................................... 1030 I2C Bus Functional Overview ...................................................................................... 1030 Available Speed Modes ............................................................................................. 1033 Interrupts .................................................................................................................. 1035 Loopback Operation .................................................................................................. 1036 Command Sequence Flow Charts .............................................................................. 1036 Initialization and Configuration .................................................................................... 1043 Register Map ............................................................................................................ 1044 Register Descriptions (I2C Master) .............................................................................. 1045 Register Descriptions (I2C Slave) ............................................................................... 1060 Register Descriptions (I2C Status and Control) ............................................................ 1070 17 Controller Area Network (CAN) Module ........................................................... 1073 17.1 Block Diagram ........................................................................................................... 1074 17.2 Signal Description ..................................................................................................... 1074 17.3 Functional Description ............................................................................................... 1075 17.3.1 Initialization ............................................................................................................... 1076 17.3.2 Operation .................................................................................................................. 1077 17.3.3 Transmitting Message Objects ................................................................................... 1078 17.3.4 Configuring a Transmit Message Object ...................................................................... 1078 17.3.5 Updating a Transmit Message Object ......................................................................... 1079 17.3.6 Accepting Received Message Objects ........................................................................ 1080 17.3.7 Receiving a Data Frame ............................................................................................ 1080 17.3.8 Receiving a Remote Frame ........................................................................................ 1080 17.3.9 Receive/Transmit Priority ........................................................................................... 1081 17.3.10 Configuring a Receive Message Object ...................................................................... 1081 17.3.11 Handling of Received Message Objects ...................................................................... 1082 17.3.12 Handling of Interrupts ................................................................................................ 1084 17.3.13 Test Mode ................................................................................................................. 1085 17.3.14 Bit Timing Configuration Error Considerations ............................................................. 1087 17.3.15 Bit Time and Bit Rate ................................................................................................. 1087 17.3.16 Calculating the Bit Timing Parameters ........................................................................ 1089 17.4 Register Map ............................................................................................................ 1092 17.5 CAN Register Descriptions ......................................................................................... 1093 18 Universal Serial Bus (USB) Controller ............................................................. 1124 18.1 18.2 18.3 18.3.1 Block Diagram ........................................................................................................... Signal Description ..................................................................................................... Functional Description ............................................................................................... Operation as a Device ............................................................................................... 8 1125 1125 1126 1126 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 18.3.2 18.3.3 18.3.4 18.4 18.4.1 18.4.2 18.5 18.6 Operation as a Host ................................................................................................... 1131 OTG Mode ................................................................................................................ 1135 DMA Operation ......................................................................................................... 1137 Initialization and Configuration .................................................................................... 1138 Pin Configuration ....................................................................................................... 1138 Endpoint Configuration .............................................................................................. 1139 Register Map ............................................................................................................ 1139 Register Descriptions ................................................................................................. 1145 19 Analog Comparators .......................................................................................... 1239 19.1 19.2 19.3 19.3.1 19.4 19.5 19.6 Block Diagram ........................................................................................................... Signal Description ..................................................................................................... Functional Description ............................................................................................... Internal Reference Programming ................................................................................ Initialization and Configuration .................................................................................... Register Map ............................................................................................................ Register Descriptions ................................................................................................. 1240 1240 1241 1242 1243 1244 1244 20 Pulse Width Modulator (PWM) .......................................................................... 1254 20.1 20.2 20.3 20.3.1 20.3.2 20.3.3 20.3.4 20.3.5 20.3.6 20.3.7 20.3.8 20.4 20.5 20.6 Block Diagram ........................................................................................................... 1255 Signal Description ..................................................................................................... 1256 Functional Description ............................................................................................... 1259 PWM Timer ............................................................................................................... 1259 PWM Comparators .................................................................................................... 1259 PWM Signal Generator .............................................................................................. 1260 Dead-Band Generator ............................................................................................... 1261 Interrupt/ADC-Trigger Selector ................................................................................... 1261 Synchronization Methods .......................................................................................... 1262 Fault Conditions ........................................................................................................ 1263 Output Control Block .................................................................................................. 1263 Initialization and Configuration .................................................................................... 1264 Register Map ............................................................................................................ 1265 Register Descriptions ................................................................................................. 1268 21 Quadrature Encoder Interface (QEI) ................................................................. 1334 21.1 21.2 21.3 21.4 21.5 21.6 Block Diagram ........................................................................................................... Signal Description ..................................................................................................... Functional Description ............................................................................................... Initialization and Configuration .................................................................................... Register Map ............................................................................................................ Register Descriptions ................................................................................................. 22 Pin Diagram ........................................................................................................ 1356 1334 1335 1336 1338 1339 1339 23 Signal Tables ...................................................................................................... 1357 23.1 Connections for Unused Signals ................................................................................. 1406 24 Operating Characteristics ................................................................................. 1408 25 Electrical Characteristics .................................................................................. 1409 25.1 25.2 25.3 25.4 Maximum Ratings ...................................................................................................... Recommended Operating Conditions ......................................................................... Load Conditions ........................................................................................................ JTAG and Boundary Scan .......................................................................................... November 08, 2011 1409 1409 1410 1411 9 Texas Instruments-Advance Information Table of Contents 25.5 Power and Brown-Out ............................................................................................... 1412 25.6 Reset ........................................................................................................................ 1413 25.7 On-Chip Low Drop-Out (LDO) Regulator ..................................................................... 1414 25.8 Clocks ...................................................................................................................... 1415 25.8.1 PLL Specifications ..................................................................................................... 1415 25.8.2 PIOSC Specifications ................................................................................................ 1416 25.8.3 Internal 30-kHz Oscillator Specifications ..................................................................... 1416 25.8.4 Hibernation Clock Source Specifications ..................................................................... 1416 25.8.5 Main Oscillator Specifications ..................................................................................... 1417 25.8.6 System Clock Specification with ADC Operation .......................................................... 1419 25.8.7 System Clock Specification with USB Operation .......................................................... 1419 25.9 Sleep Modes ............................................................................................................. 1419 25.10 Hibernation Module ................................................................................................... 1420 25.11 Flash Memory and EEPROM ..................................................................................... 1421 25.12 GPIO Module ............................................................................................................ 1421 25.13 Analog-to-Digital Converter (ADC) .............................................................................. 1422 25.14 Synchronous Serial Interface (SSI) ............................................................................. 1425 25.15 Inter-Integrated Circuit (I2C) Interface ......................................................................... 1427 25.16 Universal Serial Bus (USB) Controller ......................................................................... 1428 25.17 Analog Comparator ................................................................................................... 1428 25.18 Current Consumption ................................................................................................. 1428 25.18.1 Preliminary Current Consumption ............................................................................... 1428 A Register Quick Reference ................................................................................. 1431 B Ordering and Contact Information ................................................................... 1486 B.1 B.2 B.3 B.4 Ordering Information .................................................................................................. Part Markings ............................................................................................................ Kits ........................................................................................................................... Support Information ................................................................................................... C Package Information .......................................................................................... 1488 C.1 C.1.1 157-Ball BGA Package .............................................................................................. 1488 Package Dimensions ................................................................................................. 1488 10 1486 1486 1486 1487 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller List of Figures Figure 1-1. Figure 1-2. Figure 2-1. Figure 2-2. Figure 2-3. Figure 2-4. Figure 2-5. Figure 2-6. Figure 2-7. Figure 3-1. Figure 3-2. Figure 4-1. Figure 4-2. Figure 4-3. Figure 4-4. Figure 4-5. Figure 5-1. Figure 5-2. Figure 5-3. Figure 5-4. Figure 5-5. Figure 5-6. Figure 7-1. Figure 7-2. Figure 7-3. Figure 7-4. Figure 8-1. Figure 8-2. Figure 9-1. Figure 9-2. Figure 9-3. Figure 9-4. Figure 9-5. Figure 9-6. Figure 10-1. Figure 10-2. Figure 10-3. Figure 10-4. Figure 11-1. Figure 11-2. Figure 11-3. Figure 11-4. Figure 11-5. Figure 11-6. Figure 11-7. Stellaris LM4F Block Diagram .............................................................................. 44 Stellaris LM4F232H5BB Microcontroller High-Level Block Diagram ........................ 48 CPU Block Diagram ............................................................................................. 71 TPIU Block Diagram ............................................................................................ 72 Cortex-M4F Register Set ...................................................................................... 75 Bit-Band Mapping ................................................................................................ 99 Data Storage ..................................................................................................... 100 Vector Table ...................................................................................................... 108 Exception Stack Frame ...................................................................................... 111 SRD Use Example ............................................................................................. 130 FPU Register Bank ............................................................................................ 133 JTAG Module Block Diagram .............................................................................. 203 Test Access Port State Machine ......................................................................... 206 IDCODE Register Format ................................................................................... 212 BYPASS Register Format ................................................................................... 212 Boundary Scan Register Format ......................................................................... 213 Basic RST Configuration .................................................................................... 217 External Circuitry to Extend Power-On Reset ....................................................... 217 Reset Circuit Controlled by Switch ...................................................................... 218 Power Architecture ............................................................................................ 221 Main Clock Tree ................................................................................................ 223 Module Clock Selection ...................................................................................... 230 Hibernation Module Block Diagram ..................................................................... 523 Using a Crystal as the Hibernation Clock Source with a Single Battery Source ...... 526 Using a Dedicated Oscillator as the Hibernation Clock Source with VDD3ON Mode ................................................................................................................ 526 Using a Regulator for Both VDD and VBAT ............................................................ 527 Internal Memory Block Diagram .......................................................................... 552 EEPROM Block Diagram ................................................................................... 553 μDMA Block Diagram ......................................................................................... 611 Example of Ping-Pong μDMA Transaction ........................................................... 617 Memory Scatter-Gather, Setup and Configuration ................................................ 619 Memory Scatter-Gather, μDMA Copy Sequence .................................................. 620 Peripheral Scatter-Gather, Setup and Configuration ............................................. 622 Peripheral Scatter-Gather, μDMA Copy Sequence ............................................... 623 Digital I/O Pads ................................................................................................. 679 Analog/Digital I/O Pads ...................................................................................... 680 GPIODATA Write Example ................................................................................. 681 GPIODATA Read Example ................................................................................. 681 GPTM Module Block Diagram ............................................................................ 735 Reading the RTC Value ...................................................................................... 743 Input Edge-Count Mode Example, Counting Down ............................................... 745 16-Bit Input Edge-Time Mode Example ............................................................... 746 16-Bit PWM Mode Example ................................................................................ 748 CCP Output, GPTMTnMATCHR > GPTMTnILR ................................................... 748 CCP Output, GPTMTnMATCHR = GPTMTnILR ................................................... 749 November 08, 2011 11 Texas Instruments-Advance Information Table of Contents Figure 11-8. Figure 11-9. Figure 12-1. Figure 13-1. Figure 13-2. Figure 13-3. Figure 13-4. Figure 13-5. Figure 13-6. Figure 13-7. Figure 13-8. Figure 13-9. Figure 13-10. Figure 13-11. Figure 13-12. Figure 13-13. Figure 13-14. Figure 14-1. Figure 14-2. Figure 14-3. Figure 14-4. Figure 14-5. Figure 15-1. Figure 15-2. Figure 15-3. Figure 15-4. Figure 15-5. Figure 15-6. Figure 15-7. Figure 15-8. Figure 15-9. Figure 15-10. Figure 15-11. Figure 15-12. Figure 16-1. Figure 16-2. Figure 16-3. Figure 16-4. Figure 16-5. Figure 16-6. Figure 16-7. Figure 16-8. Figure 16-9. Figure 16-10. Figure 16-11. CCP Output, GPTMTnILR > GPTMTnMATCHR ................................................... 749 Timer Daisy Chain ............................................................................................. 750 WDT Module Block Diagram .............................................................................. 805 Implementation of Two ADC Blocks .................................................................... 830 ADC Module Block Diagram ............................................................................... 831 ADC Sample Phases ......................................................................................... 835 Doubling the ADC Sample Rate .......................................................................... 835 Skewed Sampling .............................................................................................. 836 Sample Averaging Example ............................................................................... 837 ADC Input Equivalency Diagram ......................................................................... 838 ADC Voltage Reference ..................................................................................... 838 ADC Conversion Result ..................................................................................... 839 Differential Voltage Representation ..................................................................... 841 Internal Temperature Sensor Characteristic ......................................................... 842 Low-Band Operation (CIC=0x0 and/or CTC=0x0) ................................................ 844 Mid-Band Operation (CIC=0x1 and/or CTC=0x1) ................................................. 845 High-Band Operation (CIC=0x3 and/or CTC=0x3) ................................................ 846 UART Module Block Diagram ............................................................................. 919 UART Character Frame ..................................................................................... 921 IrDA Data Modulation ......................................................................................... 923 LIN Message ..................................................................................................... 925 LIN Synchronization Field ................................................................................... 926 SSI Module Block Diagram ................................................................................. 986 TI Synchronous Serial Frame Format (Single Transfer) ........................................ 990 TI Synchronous Serial Frame Format (Continuous Transfer) ................................ 990 Freescale SPI Format (Single Transfer) with SPO=0 and SPH=0 .......................... 991 Freescale SPI Format (Continuous Transfer) with SPO=0 and SPH=0 .................. 991 Freescale SPI Frame Format with SPO=0 and SPH=1 ......................................... 992 Freescale SPI Frame Format (Single Transfer) with SPO=1 and SPH=0 ............... 993 Freescale SPI Frame Format (Continuous Transfer) with SPO=1 and SPH=0 ........ 993 Freescale SPI Frame Format with SPO=1 and SPH=1 ......................................... 994 MICROWIRE Frame Format (Single Frame) ........................................................ 995 MICROWIRE Frame Format (Continuous Transfer) ............................................. 996 MICROWIRE Frame Format, SSIFss Input Setup and Hold Requirements ............ 996 I2C Block Diagram ........................................................................................... 1029 I2C Bus Configuration ....................................................................................... 1030 START and STOP Conditions ........................................................................... 1031 Complete Data Transfer with a 7-Bit Address ..................................................... 1031 R/S Bit in First Byte .......................................................................................... 1032 Data Validity During Bit Transfer on the I2C Bus ................................................. 1032 Master Single TRANSMIT ................................................................................ 1037 Master Single RECEIVE ................................................................................... 1038 Master TRANSMIT with Repeated START ......................................................... 1039 Master RECEIVE with Repeated START ........................................................... 1040 Master RECEIVE with Repeated START after TRANSMIT with Repeated START ............................................................................................................ 1041 Figure 16-12. Master TRANSMIT with Repeated START after RECEIVE with Repeated START ............................................................................................................ 1042 12 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 16-13. Figure 17-1. Figure 17-2. Figure 17-3. Figure 17-4. Figure 18-1. Figure 19-1. Figure 19-2. Figure 19-3. Figure 20-1. Figure 20-2. Figure 20-3. Figure 20-4. Figure 20-5. Figure 20-6. Figure 21-1. Figure 21-2. Figure 22-1. Figure 25-1. Figure 25-2. Figure 25-3. Figure 25-4. Figure 25-5. Figure 25-6. Figure 25-7. Figure 25-8. Figure 25-9. Figure 25-10. Figure 25-11. Figure 25-12. Figure 25-13. Slave Command Sequence .............................................................................. 1043 CAN Controller Block Diagram .......................................................................... 1074 CAN Data/Remote Frame ................................................................................. 1076 Message Objects in a FIFO Buffer .................................................................... 1084 CAN Bit Time ................................................................................................... 1088 USB Module Block Diagram ............................................................................. 1125 Analog Comparator Module Block Diagram ....................................................... 1240 Structure of Comparator Unit ............................................................................ 1241 Comparator Internal Reference Structure .......................................................... 1242 PWM Module Diagram ..................................................................................... 1256 PWM Generator Block Diagram ........................................................................ 1256 PWM Count-Down Mode .................................................................................. 1260 PWM Count-Up/Down Mode ............................................................................. 1260 PWM Generation Example In Count-Up/Down Mode .......................................... 1261 PWM Dead-Band Generator ............................................................................. 1261 QEI Block Diagram .......................................................................................... 1335 Quadrature Encoder and Velocity Predivider Operation ...................................... 1337 157-Ball BGA Package Pin Diagram (Top View) ................................................. 1356 Load Conditions ............................................................................................... 1410 JTAG Test Clock Input Timing ........................................................................... 1411 JTAG Test Access Port (TAP) Timing ................................................................ 1412 Power-On and Brown-Out Reset and Voltage Parameters .................................. 1413 Brown-Out Reset Timing .................................................................................. 1413 External Reset Timing (RST) ............................................................................ 1414 Software Reset Timing ..................................................................................... 1414 Watchdog Reset Timing ................................................................................... 1414 MOSC Failure Reset Timing ............................................................................. 1414 Hibernation Module Timing ............................................................................... 1420 ADC External Reference Filtering ..................................................................... 1424 ADC Input Equivalency Diagram ....................................................................... 1425 SSI Timing for TI Frame Format (FRF=01), Single Transfer Timing Measurement .................................................................................................. 1426 Figure 25-14. SSI Timing for MICROWIRE Frame Format (FRF=10), Single Transfer ............... 1426 Figure 25-15. SSI Timing for SPI Frame Format (FRF=00), with SPH=1 ................................... 1427 Figure 25-16. I2C Timing ....................................................................................................... 1428 Figure C-1. Stellaris LM4F232H5BB 157-Ball BGA Package Dimensions .............................. 1489 November 08, 2011 13 Texas Instruments-Advance Information Table of Contents List of Tables Table 1. Table 2. Table 1-1. Table 1-2. Table 1-3. Table 2-1. Table 2-2. Table 2-3. Table 2-4. Table 2-5. Table 2-6. Table 2-7. Table 2-8. Table 2-9. Table 2-10. Table 2-11. Table 2-12. Table 2-13. Table 3-1. Table 3-2. Table 3-3. Table 3-4. Table 3-5. Table 3-6. Table 3-7. Table 3-8. Table 3-9. Table 3-10. Table 4-1. Table 4-2. Table 4-3. Table 5-1. Table 5-2. Table 5-3. Table 5-4. Table 5-5. Table 5-6. Table 5-7. Table 5-8. Table 6-1. Table 7-1. Table 7-2. Table 7-3. Table 7-4. Table 7-5. Table 8-1. Revision History .................................................................................................. 39 Documentation Conventions ................................................................................ 41 Stellaris LM4F Device Series ................................................................................ 44 Stellaris LM4F230 Series ..................................................................................... 44 Stellaris LM4F Family of Devices .......................................................................... 45 Summary of Processor Mode, Privilege Level, and Stack Use ................................ 74 Processor Register Map ....................................................................................... 75 PSR Register Combinations ................................................................................. 81 Memory Map ....................................................................................................... 92 Memory Access Behavior ..................................................................................... 96 SRAM Memory Bit-Banding Regions .................................................................... 98 Peripheral Memory Bit-Banding Regions ............................................................... 98 Exception Types ................................................................................................ 103 Interrupts .......................................................................................................... 104 Exception Return Behavior ................................................................................. 112 Faults ............................................................................................................... 113 Fault Status and Fault Address Registers ............................................................ 114 Cortex-M4F Instruction Summary ....................................................................... 116 Core Peripheral Register Regions ....................................................................... 124 Memory Attributes Summary .............................................................................. 128 TEX, S, C, and B Bit Field Encoding ................................................................... 130 Cache Policy for Memory Attribute Encoding ....................................................... 131 AP Bit Field Encoding ........................................................................................ 131 Memory Region Attributes for Stellaris Microcontrollers ........................................ 132 QNaN and SNaN Handling ................................................................................. 135 Peripherals Register Map ................................................................................... 136 Interrupt Priority Levels ...................................................................................... 166 Example SIZE Field Values ................................................................................ 194 JTAG_SWD_SWO Signals (157BGA) ................................................................. 203 JTAG Port Pins State after Power-On Reset or RST assertion .............................. 204 JTAG Instruction Register Commands ................................................................. 210 System Control & Clocks Signals (157BGA) ........................................................ 214 Reset Sources ................................................................................................... 215 Clock Source Options ........................................................................................ 222 Possible System Clock Frequencies Using the SYSDIV Field ............................... 224 Examples of Possible System Clock Frequencies Using the SYSDIV2 Field .......... 225 Examples of Possible System Clock Frequencies with DIV400=1 ......................... 225 System Control Register Map ............................................................................. 231 RCC2 Fields that Override RCC Fields ............................................................... 289 System Exception Register Map ......................................................................... 514 Hibernate Signals (157BGA) .............................................................................. 523 Counter Behavior with a TRIM Value of 0x8003 ................................................... 528 Counter Behavior with a TRIM Value of 0x7FFC .................................................. 529 Hibernation Module Clock Operation ................................................................... 532 Hibernation Module Register Map ....................................................................... 534 Flash Memory Protection Policy Combinations .................................................... 556 14 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 8-2. Table 8-3. Table 9-1. Table 9-2. Table 9-3. Table 9-4. Table 9-5. Table 9-6. Table 9-7. Table 9-8. Table 9-9. Table 9-10. Table 9-11. Table 9-12. User-Programmable Flash Memory Resident Registers ....................................... 560 Flash Register Map ............................................................................................ 565 μDMA Channel Assignments .............................................................................. 612 Request Type Support ....................................................................................... 614 Control Structure Memory Map ........................................................................... 615 Channel Control Structure .................................................................................. 615 μDMA Read Example: 8-Bit Peripheral ................................................................ 624 μDMA Interrupt Assignments .............................................................................. 625 Channel Control Structure Offsets for Channel 30 ................................................ 626 Channel Control Word Configuration for Memory Transfer Example ...................... 626 Channel Control Structure Offsets for Channel 7 .................................................. 627 Channel Control Word Configuration for Peripheral Transmit Example .................. 628 Primary and Alternate Channel Control Structure Offsets for Channel 8 ................. 629 Channel Control Word Configuration for Peripheral Ping-Pong Receive Example ............................................................................................................ 630 Table 9-13. μDMA Register Map .......................................................................................... 632 Table 10-1. GPIO Pins With Non-Zero Reset Values .............................................................. 675 Table 10-2. GPIO Pins and Alternate Functions (157BGA) ..................................................... 675 Table 10-3. GPIO Pad Configuration Examples ..................................................................... 684 Table 10-4. GPIO Interrupt Configuration Example ................................................................ 684 Table 10-5. GPIO Pins With Non-Zero Reset Values .............................................................. 685 Table 10-6. GPIO Register Map ........................................................................................... 686 Table 10-7. GPIO Pins With Non-Zero Reset Values .............................................................. 698 Table 10-8. GPIO Pins With Non-Zero Reset Values .............................................................. 705 Table 10-9. GPIO Pins With Non-Zero Reset Values .............................................................. 707 Table 10-10. GPIO Pins With Non-Zero Reset Values .............................................................. 710 Table 10-11. GPIO Pins With Non-Zero Reset Values .............................................................. 717 Table 11-1. Available CCP Pins ............................................................................................ 735 Table 11-2. General-Purpose Timers Signals (157BGA) ......................................................... 736 Table 11-3. General-Purpose Timer Capabilities .................................................................... 739 Table 11-4. Counter Values When the Timer is Enabled in Periodic or One-Shot Modes .......... 740 Table 11-5. 16-Bit Timer With Prescaler Configurations ......................................................... 741 Table 11-6. 32-Bit Timer (configured in 32/64-bit mode) With Prescaler Configurations ............ 741 Table 11-7. Counter Values When the Timer is Enabled in RTC Mode .................................... 742 Table 11-8. Counter Values When the Timer is Enabled in Input Edge-Count Mode ................. 744 Table 11-9. Counter Values When the Timer is Enabled in Input Event-Count Mode ................ 745 Table 11-10. Counter Values When the Timer is Enabled in PWM Mode ................................... 746 Table 11-11. Timeout Actions for GPTM Modes ...................................................................... 750 Table 11-12. Timers Register Map .......................................................................................... 756 Table 12-1. Watchdog Timers Register Map .......................................................................... 807 Table 13-1. ADC Signals (157BGA) ...................................................................................... 831 Table 13-2. Samples and FIFO Depth of Sequencers ............................................................ 833 Table 13-3. Differential Sampling Pairs ................................................................................. 840 Table 13-4. ADC Register Map ............................................................................................. 847 Table 14-1. UART Signals (157BGA) .................................................................................... 920 Table 14-2. Flow Control Mode ............................................................................................. 925 Table 14-3. UART Register Map ........................................................................................... 930 Table 15-1. SSI Signals (157BGA) ........................................................................................ 987 November 08, 2011 15 Texas Instruments-Advance Information Table of Contents Table 15-2. Table 16-1. Table 16-2. Table 16-3. Table 16-4. Table 16-5. Table 17-1. Table 17-2. Table 17-3. Table 17-4. Table 17-5. Table 18-1. Table 18-2. Table 18-3. Table 18-4. Table 18-5. Table 19-1. Table 19-2. Table 19-3. Table 20-1. Table 20-2. Table 21-1. Table 21-2. Table 23-1. Table 23-2. Table 23-3. Table 23-4. Table 23-5. Table 23-6. Table 23-7. Table 24-1. Table 24-2. Table 24-3. Table 25-1. Table 25-2. Table 25-3. Table 25-4. Table 25-5. Table 25-6. Table 25-7. Table 25-8. Table 25-9. Table 25-10. Table 25-11. Table 25-12. Table 25-13. Table 25-14. Table 25-15. SSI Register Map .............................................................................................. 998 I2C Signals (157BGA) ...................................................................................... 1029 Examples of I2C Master Timer Period versus Speed Mode ................................. 1034 Examples of I2C Master Timer Period in High-Speed Mode ................................ 1035 Inter-Integrated Circuit (I2C) Interface Register Map ........................................... 1044 Write Field Decoding for I2CMCS[3:0] Field ....................................................... 1050 Controller Area Network Signals (157BGA) ........................................................ 1075 Message Object Configurations ........................................................................ 1081 CAN Protocol Ranges ...................................................................................... 1088 CANBIT Register Values .................................................................................. 1088 CAN Register Map ........................................................................................... 1092 USB Signals (157BGA) .................................................................................... 1125 Remainder (MAXLOAD/4) ................................................................................ 1137 Actual Bytes Read ........................................................................................... 1137 Packet Sizes That Clear RXRDY ...................................................................... 1138 Universal Serial Bus (USB) Controller Register Map ........................................... 1139 Analog Comparators Signals (157BGA) ............................................................. 1240 Internal Reference Voltage and ACREFCTL Field Values ................................... 1242 Analog Comparators Register Map ................................................................... 1244 PWM Signals (157BGA) ................................................................................... 1257 PWM Register Map .......................................................................................... 1265 QEI Signals (157BGA) ..................................................................................... 1335 QEI Register Map ............................................................................................ 1339 GPIO Pins With Default Alternate Functions ...................................................... 1357 Signals by Pin Number ..................................................................................... 1358 Signals by Signal Name ................................................................................... 1374 Signals by Function, Except for GPIO ............................................................... 1387 GPIO Pins and Alternate Functions ................................................................... 1398 Possible Pin Assignments for Alternate Functions .............................................. 1402 Connections for Unused Signals (157-Ball BGA) ................................................ 1407 Temperature Characteristics ............................................................................. 1408 Thermal Characteristics ................................................................................... 1408 ESD Absolute Maximum Ratings ...................................................................... 1408 Maximum Ratings ............................................................................................ 1409 Recommended DC Operating Conditions .......................................................... 1409 GPIO Current Restrictions ................................................................................ 1410 GPIO Package Side Assignments ..................................................................... 1410 JTAG Characteristics ....................................................................................... 1411 Power Characteristics ...................................................................................... 1412 Reset Characteristics ....................................................................................... 1413 LDO Regulator Characteristics ......................................................................... 1414 Phase Locked Loop (PLL) Characteristics ......................................................... 1415 Actual PLL Frequency ...................................................................................... 1415 PIOSC Clock Characteristics ............................................................................ 1416 30-kHz Clock Characteristics ............................................................................ 1416 HIB Oscillator Input Characteristics ................................................................... 1416 Main Oscillator Input Characteristics ................................................................. 1417 Supported MOSC Crystal Frequencies .............................................................. 1418 16 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 25-16. Table 25-17. Table 25-18. Table 25-19. Table 25-20. Table 25-21. Table 25-22. Table 25-23. Table 25-24. Table 25-25. Table 25-26. Table 25-27. Table 25-28. Table 25-29. Table B-1. System Clock Characteristics with ADC Operation ............................................. 1419 System Clock Characteristics with USB Operation ............................................. 1419 Sleep Modes AC Characteristics ....................................................................... 1419 Hibernation Module Battery Characteristics ....................................................... 1420 Hibernation Module AC Characteristics ............................................................. 1420 Flash Memory Characteristics ........................................................................... 1421 EEPROM Characteristics ................................................................................. 1421 GPIO Module Characteristics ............................................................................ 1422 ADC Electrical Characteristics .......................................................................... 1422 SSI Characteristics .......................................................................................... 1425 I2C Characteristics ........................................................................................... 1427 Analog Comparator Characteristics ................................................................... 1428 Analog Comparator Voltage Reference Characteristics ...................................... 1428 Preliminary Current Consumption ..................................................................... 1429 Part Ordering Information ................................................................................. 1486 November 08, 2011 17 Texas Instruments-Advance Information Table of Contents List of Registers The Cortex-M4F Processor ........................................................................................................... 69 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Cortex General-Purpose Register 0 (R0) ........................................................................... 77 Cortex General-Purpose Register 1 (R1) ........................................................................... 77 Cortex General-Purpose Register 2 (R2) ........................................................................... 77 Cortex General-Purpose Register 3 (R3) ........................................................................... 77 Cortex General-Purpose Register 4 (R4) ........................................................................... 77 Cortex General-Purpose Register 5 (R5) ........................................................................... 77 Cortex General-Purpose Register 6 (R6) ........................................................................... 77 Cortex General-Purpose Register 7 (R7) ........................................................................... 77 Cortex General-Purpose Register 8 (R8) ........................................................................... 77 Cortex General-Purpose Register 9 (R9) ........................................................................... 77 Cortex General-Purpose Register 10 (R10) ....................................................................... 77 Cortex General-Purpose Register 11 (R11) ........................................................................ 77 Cortex General-Purpose Register 12 (R12) ....................................................................... 77 Stack Pointer (SP) ........................................................................................................... 78 Link Register (LR) ............................................................................................................ 79 Program Counter (PC) ..................................................................................................... 80 Program Status Register (PSR) ........................................................................................ 81 Priority Mask Register (PRIMASK) .................................................................................... 85 Fault Mask Register (FAULTMASK) .................................................................................. 86 Base Priority Mask Register (BASEPRI) ............................................................................ 87 Control Register (CONTROL) ........................................................................................... 88 Floating-Point Status Control (FPSC) ................................................................................ 90 Cortex-M4 Peripherals ................................................................................................................. 124 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: SysTick Control and Status Register (STCTRL), offset 0x010 ........................................... 140 SysTick Reload Value Register (STRELOAD), offset 0x014 .............................................. 142 SysTick Current Value Register (STCURRENT), offset 0x018 ........................................... 143 Interrupt 0-31 Set Enable (EN0), offset 0x100 .................................................................. 144 Interrupt 32-63 Set Enable (EN1), offset 0x104 ................................................................ 144 Interrupt 64-95 Set Enable (EN2), offset 0x108 ................................................................ 144 Interrupt 96-127 Set Enable (EN3), offset 0x10C ............................................................. 144 Interrupt 128-131 Set Enable (EN4), offset 0x110 ............................................................ 145 Interrupt 0-31 Clear Enable (DIS0), offset 0x180 .............................................................. 146 Interrupt 32-63 Clear Enable (DIS1), offset 0x184 ............................................................ 146 Interrupt 64-95 Clear Enable (DIS2), offset 0x188 ............................................................ 146 Interrupt 96-127 Clear Enable (DIS3), offset 0x18C .......................................................... 146 Interrupt 128-131 Clear Enable (DIS4), offset 0x190 ........................................................ 147 Interrupt 0-31 Set Pending (PEND0), offset 0x200 ........................................................... 148 Interrupt 32-63 Set Pending (PEND1), offset 0x204 ......................................................... 148 Interrupt 64-95 Set Pending (PEND2), offset 0x208 ......................................................... 148 Interrupt 96-127 Set Pending (PEND3), offset 0x20C ....................................................... 148 Interrupt 128-131 Set Pending (PEND4), offset 0x210 ...................................................... 149 Interrupt 0-31 Clear Pending (UNPEND0), offset 0x280 ................................................... 150 Interrupt 32-63 Clear Pending (UNPEND1), offset 0x284 .................................................. 150 Interrupt 64-95 Clear Pending (UNPEND2), offset 0x288 .................................................. 150 18 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: Register 36: Register 37: Register 38: Register 39: Register 40: Register 41: Register 42: Register 43: Register 44: Register 45: Register 46: Register 47: Register 48: Register 49: Register 50: Register 51: Register 52: Register 53: Register 54: Register 55: Register 56: Register 57: Register 58: Register 59: Register 60: Register 61: Register 62: Register 63: Register 64: Register 65: Register 66: Register 67: Register 68: Register 69: Interrupt 96-127 Clear Pending (UNPEND3), offset 0x28C ............................................... 150 Interrupt 128-131 Clear Pending (UNPEND4), offset 0x290 .............................................. 151 Interrupt 0-31 Active Bit (ACTIVE0), offset 0x300 ............................................................. 152 Interrupt 32-63 Active Bit (ACTIVE1), offset 0x304 ........................................................... 152 Interrupt 64-95 Active Bit (ACTIVE2), offset 0x308 ........................................................... 152 Interrupt 96-127 Active Bit (ACTIVE3), offset 0x30C ........................................................ 152 Interrupt 128-131 Active Bit (ACTIVE4), offset 0x310 ....................................................... 153 Interrupt 0-3 Priority (PRI0), offset 0x400 ......................................................................... 154 Interrupt 4-7 Priority (PRI1), offset 0x404 ......................................................................... 154 Interrupt 8-11 Priority (PRI2), offset 0x408 ....................................................................... 154 Interrupt 12-15 Priority (PRI3), offset 0x40C .................................................................... 154 Interrupt 16-19 Priority (PRI4), offset 0x410 ..................................................................... 154 Interrupt 20-23 Priority (PRI5), offset 0x414 ..................................................................... 154 Interrupt 24-27 Priority (PRI6), offset 0x418 ..................................................................... 154 Interrupt 28-31 Priority (PRI7), offset 0x41C .................................................................... 154 Interrupt 32-35 Priority (PRI8), offset 0x420 ..................................................................... 154 Interrupt 36-39 Priority (PRI9), offset 0x424 ..................................................................... 154 Interrupt 40-43 Priority (PRI10), offset 0x428 ................................................................... 154 Interrupt 44-47 Priority (PRI11), offset 0x42C ................................................................... 154 Interrupt 48-51 Priority (PRI12), offset 0x430 ................................................................... 154 Interrupt 52-55 Priority (PRI13), offset 0x434 ................................................................... 154 Interrupt 56-59 Priority (PRI14), offset 0x438 ................................................................... 154 Interrupt 60-63 Priority (PRI15), offset 0x43C .................................................................. 154 Interrupt 64-67 Priority (PRI16), offset 0x440 ................................................................... 156 Interrupt 68-71 Priority (PRI17), offset 0x444 ................................................................... 156 Interrupt 72-75 Priority (PRI18), offset 0x448 ................................................................... 156 Interrupt 76-79 Priority (PRI19), offset 0x44C .................................................................. 156 Interrupt 80-83 Priority (PRI20), offset 0x450 ................................................................... 156 Interrupt 84-87 Priority (PRI21), offset 0x454 ................................................................... 156 Interrupt 88-91 Priority (PRI22), offset 0x458 ................................................................... 156 Interrupt 92-95 Priority (PRI23), offset 0x45C .................................................................. 156 Interrupt 96-99 Priority (PRI24), offset 0x460 ................................................................... 156 Interrupt 100-103 Priority (PRI25), offset 0x464 ............................................................... 156 Interrupt 104-107 Priority (PRI26), offset 0x468 ............................................................... 156 Interrupt 108-111 Priority (PRI27), offset 0x46C ............................................................... 156 Interrupt 112-115 Priority (PRI28), offset 0x470 ................................................................ 156 Interrupt 116-119 Priority (PRI29), offset 0x474 ................................................................ 156 Interrupt 120-123 Priority (PRI30), offset 0x478 ............................................................... 156 Interrupt 124-127 Priority (PRI31), offset 0x47C ............................................................... 156 Interrupt 128-131 Priority (PRI32), offset 0x480 ............................................................... 156 Software Trigger Interrupt (SWTRIG), offset 0xF00 .......................................................... 158 Auxiliary Control (ACTLR), offset 0x008 .......................................................................... 159 CPU ID Base (CPUID), offset 0xD00 ............................................................................... 161 Interrupt Control and State (INTCTRL), offset 0xD04 ........................................................ 162 Vector Table Offset (VTABLE), offset 0xD08 .................................................................... 165 Application Interrupt and Reset Control (APINT), offset 0xD0C ......................................... 166 System Control (SYSCTRL), offset 0xD10 ....................................................................... 168 Configuration and Control (CFGCTRL), offset 0xD14 ....................................................... 170 November 08, 2011 19 Texas Instruments-Advance Information Table of Contents Register 70: Register 71: Register 72: Register 73: Register 74: Register 75: Register 76: Register 77: Register 78: Register 79: Register 80: Register 81: Register 82: Register 83: Register 84: Register 85: Register 86: Register 87: Register 88: Register 89: Register 90: Register 91: Register 92: System Handler Priority 1 (SYSPRI1), offset 0xD18 ......................................................... 172 System Handler Priority 2 (SYSPRI2), offset 0xD1C ........................................................ 173 System Handler Priority 3 (SYSPRI3), offset 0xD20 ......................................................... 174 System Handler Control and State (SYSHNDCTRL), offset 0xD24 .................................... 175 Configurable Fault Status (FAULTSTAT), offset 0xD28 ..................................................... 179 Hard Fault Status (HFAULTSTAT), offset 0xD2C .............................................................. 185 Memory Management Fault Address (MMADDR), offset 0xD34 ........................................ 186 Bus Fault Address (FAULTADDR), offset 0xD38 .............................................................. 187 MPU Type (MPUTYPE), offset 0xD90 ............................................................................. 188 MPU Control (MPUCTRL), offset 0xD94 .......................................................................... 189 MPU Region Number (MPUNUMBER), offset 0xD98 ....................................................... 191 MPU Region Base Address (MPUBASE), offset 0xD9C ................................................... 192 MPU Region Base Address Alias 1 (MPUBASE1), offset 0xDA4 ....................................... 192 MPU Region Base Address Alias 2 (MPUBASE2), offset 0xDAC ...................................... 192 MPU Region Base Address Alias 3 (MPUBASE3), offset 0xDB4 ....................................... 192 MPU Region Attribute and Size (MPUATTR), offset 0xDA0 ............................................... 194 MPU Region Attribute and Size Alias 1 (MPUATTR1), offset 0xDA8 .................................. 194 MPU Region Attribute and Size Alias 2 (MPUATTR2), offset 0xDB0 .................................. 194 MPU Region Attribute and Size Alias 3 (MPUATTR3), offset 0xDB8 .................................. 194 Coprocessor Access Control (CPAC), offset 0xD88 .......................................................... 197 Floating-Point Context Control (FPCC), offset 0xF34 ........................................................ 198 Floating-Point Context Address (FPCA), offset 0xF38 ...................................................... 200 Floating-Point Default Status Control (FPDSC), offset 0xF3C ........................................... 201 System Control ............................................................................................................................ 214 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Device Identification 0 (DID0), offset 0x000 ..................................................................... 237 Device Identification 1 (DID1), offset 0x004 ..................................................................... 239 Device Capabilities 0 (DC0), offset 0x008 ........................................................................ 241 Device Capabilities 1 (DC1), offset 0x010 ........................................................................ 242 Device Capabilities 2 (DC2), offset 0x014 ........................................................................ 245 Device Capabilities 3 (DC3), offset 0x018 ........................................................................ 248 Device Capabilities 4 (DC4), offset 0x01C ....................................................................... 252 Device Capabilities 5 (DC5), offset 0x020 ........................................................................ 255 Device Capabilities 6 (DC6), offset 0x024 ........................................................................ 257 Device Capabilities 7 (DC7), offset 0x028 ........................................................................ 258 Device Capabilities 8 (DC8), offset 0x02C ....................................................................... 261 Brown-Out Reset Control (PBORCTL), offset 0x030 ........................................................ 264 Software Reset Control 0 (SRCR0), offset 0x040 ............................................................. 265 Software Reset Control 1 (SRCR1), offset 0x044 ............................................................. 267 Software Reset Control 2 (SRCR2), offset 0x048 ............................................................. 270 Raw Interrupt Status (RIS), offset 0x050 .......................................................................... 272 Interrupt Mask Control (IMC), offset 0x054 ...................................................................... 274 Masked Interrupt Status and Clear (MISC), offset 0x058 .................................................. 276 Reset Cause (RESC), offset 0x05C ................................................................................ 278 Run-Mode Clock Configuration (RCC), offset 0x060 ......................................................... 280 GPIO High-Performance Bus Control (GPIOHBCTL), offset 0x06C ................................... 285 Run-Mode Clock Configuration 2 (RCC2), offset 0x070 .................................................... 289 Main Oscillator Control (MOSCCTL), offset 0x07C ........................................................... 292 Run Mode Clock Gating Control Register 0 (RCGC0), offset 0x100 ................................... 293 20 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: Register 36: Register 37: Register 38: Register 39: Register 40: Register 41: Register 42: Register 43: Register 44: Register 45: Register 46: Register 47: Register 48: Register 49: Register 50: Register 51: Register 52: Register 53: Register 54: Register 55: Register 56: Register 57: Register 58: Register 59: Register 60: Register 61: Register 62: Register 63: Register 64: Register 65: Register 66: Register 67: Register 68: Register 69: Register 70: Register 71: Run Mode Clock Gating Control Register 1 (RCGC1), offset 0x104 ................................... 296 Run Mode Clock Gating Control Register 2 (RCGC2), offset 0x108 ................................... 300 Sleep Mode Clock Gating Control Register 0 (SCGC0), offset 0x110 ................................. 303 Sleep Mode Clock Gating Control Register 1 (SCGC1), offset 0x114 ................................. 306 Sleep Mode Clock Gating Control Register 2 (SCGC2), offset 0x118 ................................. 310 Deep Sleep Mode Clock Gating Control Register 0 (DCGC0), offset 0x120 ....................... 313 Deep-Sleep Mode Clock Gating Control Register 1 (DCGC1), offset 0x124 ....................... 316 Deep Sleep Mode Clock Gating Control Register 2 (DCGC2), offset 0x128 ....................... 320 Deep Sleep Clock Configuration (DSLPCLKCFG), offset 0x144 ........................................ 323 System Properties (SYSPROP), offset 0x14C .................................................................. 325 Precision Internal Oscillator Calibration (PIOSCCAL), offset 0x150 ................................... 326 Precision Internal Oscillator Statistics (PIOSCSTAT), offset 0x154 .................................... 328 PLL Frequency 0 (PLLFREQ0), offset 0x160 ................................................................... 329 PLL Frequency 1 (PLLFREQ1), offset 0x164 ................................................................... 330 PLL Status (PLLSTAT), offset 0x168 ............................................................................... 331 Device Capabilities 9 (DC9), offset 0x190 ........................................................................ 332 Non-Volatile Memory Information (NVMSTAT), offset 0x1A0 ............................................. 334 Watchdog Timer Peripheral Present (PPWD), offset 0x300 ............................................... 335 16/32-Bit General-Purpose Timer Peripheral Present (PPTIMER), offset 0x304 ................. 336 General-Purpose Input/Output Peripheral Present (PPGPIO), offset 0x308 ........................ 338 Micro Direct Memory Access Peripheral Present (PPDMA), offset 0x30C .......................... 341 Hibernation Peripheral Present (PPHIB), offset 0x314 ...................................................... 342 Universal Asynchronous Receiver/Transmitter Peripheral Present (PPUART), offset 0x318 ........................................................................................................................... 343 Synchronous Serial Interface Peripheral Present (PPSSI), offset 0x31C ............................ 345 Inter-Integrated Circuit Peripheral Present (PPI2C), offset 0x320 ...................................... 347 Universal Serial Bus Peripheral Present (PPUSB), offset 0x328 ........................................ 349 Controller Area Network Peripheral Present (PPCAN), offset 0x334 .................................. 350 Analog-to-Digital Converter Peripheral Present (PPADC), offset 0x338 ............................. 351 Analog Comparator Peripheral Present (PPACMP), offset 0x33C ...................................... 352 Pulse Width Modulator Peripheral Present (PPPWM), offset 0x340 ................................... 353 Quadrature Encoder Interface Peripheral Present (PPQEI), offset 0x344 ........................... 354 EEPROM Peripheral Present (PPEEPROM), offset 0x358 ................................................ 355 32/64-Bit Wide General-Purpose Timer Peripheral Present (PPWTIMER), offset 0x35C ..... 356 Watchdog Timer Software Reset (SRWD), offset 0x500 ................................................... 358 16/32-Bit General-Purpose Timer Software Reset (SRTIMER), offset 0x504 ...................... 360 General-Purpose Input/Output Software Reset (SRGPIO), offset 0x508 ............................ 362 Micro Direct Memory Access Software Reset (SRDMA), offset 0x50C ............................... 365 Hibernation Software Reset (SRHIB), offset 0x514 ........................................................... 366 Universal Asynchronous Receiver/Transmitter Software Reset (SRUART), offset 0x518 .... 367 Synchronous Serial Interface Software Reset (SRSSI), offset 0x51C ................................ 369 Inter-Integrated Circuit Software Reset (SRI2C), offset 0x520 ........................................... 371 Universal Serial Bus Software Reset (SRUSB), offset 0x528 ............................................ 373 Controller Area Network Software Reset (SRCAN), offset 0x534 ....................................... 374 Analog-to-Digital Converter Software Reset (SRADC), offset 0x538 .................................. 376 Analog Comparator Software Reset (SRACMP), offset 0x53C .......................................... 378 Pulse Width Modulator Software Reset (SRPWM), offset 0x540 ....................................... 379 Quadrature Encoder Interface Software Reset (SRQEI), offset 0x544 ............................... 381 November 08, 2011 21 Texas Instruments-Advance Information Table of Contents Register 72: Register 73: Register 74: Register 75: Register 76: Register 77: Register 78: Register 79: Register 80: Register 81: Register 82: Register 83: Register 84: Register 85: Register 86: Register 87: Register 88: Register 89: Register 90: Register 91: Register 92: Register 93: Register 94: Register 95: Register 96: Register 97: Register 98: Register 99: Register 100: Register 101: Register 102: Register 103: Register 104: Register 105: EEPROM Software Reset (SREEPROM), offset 0x558 .................................................... 383 32/64-Bit Wide General-Purpose Timer Software Reset (SRWTIMER), offset 0x55C .......... 384 Watchdog Timer Run Mode Clock Gating Control (RCGCWD), offset 0x600 ...................... 386 16/32-Bit General-Purpose Timer Run Mode Clock Gating Control (RCGCTIMER), offset 0x604 ........................................................................................................................... 387 General-Purpose Input/Output Run Mode Clock Gating Control (RCGCGPIO), offset 0x608 ........................................................................................................................... 389 Micro Direct Memory Access Run Mode Clock Gating Control (RCGCDMA), offset 0x60C ........................................................................................................................... 392 Hibernation Run Mode Clock Gating Control (RCGCHIB), offset 0x614 ............................. 393 Universal Asynchronous Receiver/Transmitter Run Mode Clock Gating Control (RCGCUART), offset 0x618 .................................................................................................................. 394 Synchronous Serial Interface Run Mode Clock Gating Control (RCGCSSI), offset 0x61C ........................................................................................................................... 396 Inter-Integrated Circuit Run Mode Clock Gating Control (RCGCI2C), offset 0x620 ............. 398 Universal Serial Bus Run Mode Clock Gating Control (RCGCUSB), offset 0x628 ............... 400 Controller Area Network Run Mode Clock Gating Control (RCGCCAN), offset 0x634 ......... 401 Analog-to-Digital Converter Run Mode Clock Gating Control (RCGCADC), offset 0x638 .... 402 Analog Comparator Run Mode Clock Gating Control (RCGCACMP), offset 0x63C ............. 403 Pulse Width Modulator Run Mode Clock Gating Control (RCGCPWM), offset 0x640 .......... 404 Quadrature Encoder Interface Run Mode Clock Gating Control (RCGCQEI), offset 0x644 ........................................................................................................................... 405 EEPROM Run Mode Clock Gating Control (RCGCEEPROM), offset 0x658 ....................... 406 32/64-Bit Wide General-Purpose Timer Run Mode Clock Gating Control (RCGCWTIMER), offset 0x65C .................................................................................................................. 407 Watchdog Timer Sleep Mode Clock Gating Control (SCGCWD), offset 0x700 .................... 409 16/32-Bit General-Purpose Timer Sleep Mode Clock Gating Control (SCGCTIMER), offset 0x704 ........................................................................................................................... 410 General-Purpose Input/Output Sleep Mode Clock Gating Control (SCGCGPIO), offset 0x708 ........................................................................................................................... 412 Micro Direct Memory Access Sleep Mode Clock Gating Control (SCGCDMA), offset 0x70C ........................................................................................................................... 415 Hibernation Sleep Mode Clock Gating Control (SCGCHIB), offset 0x714 ........................... 416 Universal Asynchronous Receiver/Transmitter Sleep Mode Clock Gating Control (SCGCUART), offset 0x718 ............................................................................................ 417 Synchronous Serial Interface Sleep Mode Clock Gating Control (SCGCSSI), offset 0x71C ........................................................................................................................... 419 Inter-Integrated Circuit Sleep Mode Clock Gating Control (SCGCI2C), offset 0x720 ........... 421 Universal Serial Bus Sleep Mode Clock Gating Control (SCGCUSB), offset 0x728 ............. 423 Controller Area Network Sleep Mode Clock Gating Control (SCGCCAN), offset 0x734 ....... 424 Analog-to-Digital Converter Sleep Mode Clock Gating Control (SCGCADC), offset 0x738 ........................................................................................................................... 425 Analog Comparator Sleep Mode Clock Gating Control (SCGCACMP), offset 0x73C .......... 426 Pulse Width Modulator Sleep Mode Clock Gating Control (SCGCPWM), offset 0x740 ........ 427 Quadrature Encoder Interface Sleep Mode Clock Gating Control (SCGCQEI), offset 0x744 ........................................................................................................................... 428 EEPROM Sleep Mode Clock Gating Control (SCGCEEPROM), offset 0x758 ..................... 429 32/64-Bit Wide General-Purpose Timer Sleep Mode Clock Gating Control (SCGCWTIMER), offset 0x75C .................................................................................................................. 430 22 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 106: Watchdog Timer Deep-Sleep Mode Clock Gating Control (DCGCWD), offset 0x800 .......... 432 Register 107: 16/32-Bit General-Purpose Timer Deep-Sleep Mode Clock Gating Control (DCGCTIMER), offset 0x804 .................................................................................................................. 433 Register 108: General-Purpose Input/Output Deep-Sleep Mode Clock Gating Control (DCGCGPIO), offset 0x808 ........................................................................................................................... 435 Register 109: Micro Direct Memory Access Deep-Sleep Mode Clock Gating Control (DCGCDMA), offset 0x80C ........................................................................................................................... 438 Register 110: Hibernation Deep-Sleep Mode Clock Gating Control (DCGCHIB), offset 0x814 .................. 439 Register 111: Universal Asynchronous Receiver/Transmitter Deep-Sleep Mode Clock Gating Control (DCGCUART), offset 0x818 ............................................................................................ 440 Register 112: Synchronous Serial Interface Deep-Sleep Mode Clock Gating Control (DCGCSSI), offset 0x81C ........................................................................................................................... 442 Register 113: Inter-Integrated Circuit Deep-Sleep Mode Clock Gating Control (DCGCI2C), offset 0x820 ........................................................................................................................... 444 Register 114: Universal Serial Bus Deep-Sleep Mode Clock Gating Control (DCGCUSB), offset 0x828 ........................................................................................................................... 446 Register 115: Controller Area Network Deep-Sleep Mode Clock Gating Control (DCGCCAN), offset 0x834 ........................................................................................................................... 447 Register 116: Analog-to-Digital Converter Deep-Sleep Mode Clock Gating Control (DCGCADC), offset 0x838 ........................................................................................................................... 448 Register 117: Analog Comparator Deep-Sleep Mode Clock Gating Control (DCGCACMP), offset 0x83C ........................................................................................................................... 449 Register 118: Pulse Width Modulator Deep-Sleep Mode Clock Gating Control (DCGCPWM), offset 0x840 ........................................................................................................................... 450 Register 119: Quadrature Encoder Interface Deep-Sleep Mode Clock Gating Control (DCGCQEI), offset 0x844 ........................................................................................................................... 451 Register 120: EEPROM Deep-Sleep Mode Clock Gating Control (DCGCEEPROM), offset 0x858 ........... 452 Register 121: 32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode Clock Gating Control (DCGCWTIMER), offset 0x85C ...................................................................................... 453 Register 122: Watchdog Timer Power Control (PCWD), offset 0x900 ..................................................... 455 Register 123: 16/32-Bit General-Purpose Timer Power Control (PCTIMER), offset 0x904 ....................... 457 Register 124: General-Purpose Input/Output Power Control (PCGPIO), offset 0x908 .............................. 460 Register 125: Micro Direct Memory Access Power Control (PCDMA), offset 0x90C ................................ 466 Register 126: Hibernation Power Control (PCHIB), offset 0x914 ............................................................ 467 Register 127: Universal Asynchronous Receiver/Transmitter Power Control (PCUART), offset 0x918 ...... 468 Register 128: Synchronous Serial Interface Power Control (PCSSI), offset 0x91C .................................. 472 Register 129: Inter-Integrated Circuit Power Control (PCI2C), offset 0x920 ............................................ 474 Register 130: Universal Serial Bus Power Control (PCUSB), offset 0x928 .............................................. 477 Register 131: Controller Area Network Power Control (PCCAN), offset 0x934 ........................................ 478 Register 132: Analog-to-Digital Converter Power Control (PCADC), offset 0x938 .................................... 480 Register 133: Analog Comparator Power Control (PCACMP), offset 0x93C ............................................ 482 Register 134: Pulse Width Modulator Power Control (PCPWM), offset 0x940 ......................................... 483 Register 135: Quadrature Encoder Interface Power Control (PCQEI), offset 0x944 ................................. 485 Register 136: EEPROM Power Control (PCEEPROM), offset 0x958 ...................................................... 487 Register 137: 32/64-Bit Wide General-Purpose Timer Power Control (PCWTIMER), offset 0x95C ........... 488 Register 138: Watchdog Timer Peripheral Ready (PRWD), offset 0xA00 ................................................ 491 Register 139: 16/32-Bit General-Purpose Timer Peripheral Ready (PRTIMER), offset 0xA04 ................... 492 Register 140: General-Purpose Input/Output Peripheral Ready (PRGPIO), offset 0xA08 ......................... 494 Register 141: Micro Direct Memory Access Peripheral Ready (PRDMA), offset 0xA0C ........................... 497 November 08, 2011 23 Texas Instruments-Advance Information Table of Contents Register 142: Hibernation Peripheral Ready (PRHIB), offset 0xA14 ....................................................... 498 Register 143: Universal Asynchronous Receiver/Transmitter Peripheral Ready (PRUART), offset 0xA18 ........................................................................................................................... 499 Register 144: Synchronous Serial Interface Peripheral Ready (PRSSI), offset 0xA1C ............................. 501 Register 145: Inter-Integrated Circuit Peripheral Ready (PRI2C), offset 0xA20 ....................................... 503 Register 146: Universal Serial Bus Peripheral Ready (PRUSB), offset 0xA28 ......................................... 505 Register 147: Controller Area Network Peripheral Ready (PRCAN), offset 0xA34 ................................... 506 Register 148: Analog-to-Digital Converter Peripheral Ready (PRADC), offset 0xA38 ............................... 507 Register 149: Analog Comparator Peripheral Ready (PRACMP), offset 0xA3C ....................................... 508 Register 150: Pulse Width Modulator Peripheral Ready (PRPWM), offset 0xA40 .................................... 509 Register 151: Quadrature Encoder Interface Peripheral Ready (PRQEI), offset 0xA44 ............................ 510 Register 152: EEPROM Peripheral Ready (PREEPROM), offset 0xA58 ................................................. 511 Register 153: 32/64-Bit Wide General-Purpose Timer Peripheral Ready (PRWTIMER), offset 0xA5C ...... 512 System Exception Module .......................................................................................................... 514 Register 1: Register 2: Register 3: Register 4: System Exception Raw Interrupt Status (SYSEXCRIS), offset 0x000 ................................ System Exception Interrupt Mask (SYSEXCIM), offset 0x004 ........................................... System Exception Masked Interrupt Status (SYSEXCMIS), offset 0x008 ........................... System Exception Interrupt Clear (SYSEXCIC), offset 0x00C ........................................... 515 517 519 521 Hibernation Module ..................................................................................................................... 522 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Hibernation RTC Counter (HIBRTCC), offset 0x000 ......................................................... Hibernation RTC Match 0 (HIBRTCM0), offset 0x004 ....................................................... Hibernation RTC Load (HIBRTCLD), offset 0x00C ........................................................... Hibernation Control (HIBCTL), offset 0x010 ..................................................................... Hibernation Interrupt Mask (HIBIM), offset 0x014 ............................................................. Hibernation Raw Interrupt Status (HIBRIS), offset 0x018 .................................................. Hibernation Masked Interrupt Status (HIBMIS), offset 0x01C ............................................ Hibernation Interrupt Clear (HIBIC), offset 0x020 ............................................................. Hibernation RTC Trim (HIBRTCT), offset 0x024 ............................................................... Hibernation RTC Sub Seconds (HIBRTCSS), offset 0x028 ............................................... Hibernation Data (HIBDATA), offset 0x030-0x06F ............................................................ 535 536 537 538 542 544 546 548 549 550 551 Internal Memory ........................................................................................................................... 552 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Flash Memory Address (FMA), offset 0x000 .................................................................... 568 Flash Memory Data (FMD), offset 0x004 ......................................................................... 569 Flash Memory Control (FMC), offset 0x008 ..................................................................... 570 Flash Controller Raw Interrupt Status (FCRIS), offset 0x00C ............................................ 572 Flash Controller Interrupt Mask (FCIM), offset 0x010 ........................................................ 575 Flash Controller Masked Interrupt Status and Clear (FCMISC), offset 0x014 ..................... 577 Flash Memory Control 2 (FMC2), offset 0x020 ................................................................. 580 Flash Write Buffer Valid (FWBVAL), offset 0x030 ............................................................. 581 Flash Write Buffer n (FWBn), offset 0x100 - 0x17C .......................................................... 582 Flash Size (FSIZE), offset 0xFC0 .................................................................................... 583 SRAM Size (SSIZE), offset 0xFC4 .................................................................................. 584 ROM Software Map (ROMSWMAP), offset 0xFCC ........................................................... 585 EEPROM Size Information (EESIZE), offset 0x000 .......................................................... 586 EEPROM Current Block (EEBLOCK), offset 0x004 .......................................................... 587 EEPROM Current Offset (EEOFFSET), offset 0x008 ........................................................ 588 EEPROM Read-Write (EERDWR), offset 0x010 .............................................................. 589 EEPROM Read-Write with Increment (EERDWRINC), offset 0x014 .................................. 590 24 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: Register 36: Register 37: Register 38: Register 39: Register 40: Register 41: Register 42: EEPROM Done Status (EEDONE), offset 0x018 .............................................................. 591 EEPROM Support Control and Status (EESUPP), offset 0x01C ........................................ 593 EEPROM Unlock (EEUNLOCK), offset 0x020 .................................................................. 595 EEPROM Protection (EEPROT), offset 0x030 ................................................................. 596 EEPROM Password (EEPASS0), offset 0x034 ................................................................. 597 EEPROM Password (EEPASS1), offset 0x038 ................................................................. 597 EEPROM Password (EEPASS2), offset 0x03C ................................................................ 597 EEPROM Interrupt (EEINT), offset 0x040 ........................................................................ 598 EEPROM Block Hide (EEHIDE), offset 0x050 .................................................................. 599 EEPROM Debug Mass Erase (EEDBGME), offset 0x080 ................................................. 600 EEPROM Peripheral Properties (EEPROMPP), offset 0xFC0 ........................................... 601 ROM Control (RMCTL), offset 0x0F0 .............................................................................. 602 Flash Memory Protection Read Enable 0 (FMPRE0), offset 0x130 and 0x200 ................... 603 Flash Memory Protection Read Enable 1 (FMPRE1), offset 0x204 .................................... 603 Flash Memory Protection Read Enable 2 (FMPRE2), offset 0x208 .................................... 603 Flash Memory Protection Read Enable 3 (FMPRE3), offset 0x20C ................................... 603 Flash Memory Protection Program Enable 0 (FMPPE0), offset 0x134 and 0x400 ............... 604 Flash Memory Protection Program Enable 1 (FMPPE1), offset 0x404 ............................... 604 Flash Memory Protection Program Enable 2 (FMPPE2), offset 0x408 ............................... 604 Flash Memory Protection Program Enable 3 (FMPPE3), offset 0x40C ............................... 604 Boot Configuration (BOOTCFG), offset 0x1D0 ................................................................. 606 User Register 0 (USER_REG0), offset 0x1E0 .................................................................. 609 User Register 1 (USER_REG1), offset 0x1E4 .................................................................. 609 User Register 2 (USER_REG2), offset 0x1E8 .................................................................. 609 User Register 3 (USER_REG3), offset 0x1EC ................................................................. 609 Micro Direct Memory Access (μDMA) ........................................................................................ 610 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: DMA Channel Source Address End Pointer (DMASRCENDP), offset 0x000 ...................... 634 DMA Channel Destination Address End Pointer (DMADSTENDP), offset 0x004 ................ 635 DMA Channel Control Word (DMACHCTL), offset 0x008 .................................................. 636 DMA Status (DMASTAT), offset 0x000 ............................................................................ 641 DMA Configuration (DMACFG), offset 0x004 ................................................................... 643 DMA Channel Control Base Pointer (DMACTLBASE), offset 0x008 .................................. 644 DMA Alternate Channel Control Base Pointer (DMAALTBASE), offset 0x00C .................... 645 DMA Channel Wait-on-Request Status (DMAWAITSTAT), offset 0x010 ............................. 646 DMA Channel Software Request (DMASWREQ), offset 0x014 ......................................... 647 DMA Channel Useburst Set (DMAUSEBURSTSET), offset 0x018 .................................... 648 DMA Channel Useburst Clear (DMAUSEBURSTCLR), offset 0x01C ................................. 649 DMA Channel Request Mask Set (DMAREQMASKSET), offset 0x020 .............................. 650 DMA Channel Request Mask Clear (DMAREQMASKCLR), offset 0x024 ........................... 651 DMA Channel Enable Set (DMAENASET), offset 0x028 ................................................... 652 DMA Channel Enable Clear (DMAENACLR), offset 0x02C ............................................... 653 DMA Channel Primary Alternate Set (DMAALTSET), offset 0x030 .................................... 654 DMA Channel Primary Alternate Clear (DMAALTCLR), offset 0x034 ................................. 655 DMA Channel Priority Set (DMAPRIOSET), offset 0x038 ................................................. 656 DMA Channel Priority Clear (DMAPRIOCLR), offset 0x03C .............................................. 657 DMA Bus Error Clear (DMAERRCLR), offset 0x04C ........................................................ 658 DMA Channel Assignment (DMACHASGN), offset 0x500 ................................................. 659 DMA Channel Interrupt Status (DMACHIS), offset 0x504 .................................................. 660 November 08, 2011 25 Texas Instruments-Advance Information Table of Contents Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: DMA Channel Map Select 0 (DMACHMAP0), offset 0x510 ............................................... 661 DMA Channel Map Select 1 (DMACHMAP1), offset 0x514 ............................................... 662 DMA Channel Map Select 2 (DMACHMAP2), offset 0x518 ............................................... 663 DMA Channel Map Select 3 (DMACHMAP3), offset 0x51C .............................................. 664 DMA Peripheral Identification 0 (DMAPeriphID0), offset 0xFE0 ......................................... 665 DMA Peripheral Identification 1 (DMAPeriphID1), offset 0xFE4 ......................................... 666 DMA Peripheral Identification 2 (DMAPeriphID2), offset 0xFE8 ......................................... 667 DMA Peripheral Identification 3 (DMAPeriphID3), offset 0xFEC ........................................ 668 DMA Peripheral Identification 4 (DMAPeriphID4), offset 0xFD0 ......................................... 669 DMA PrimeCell Identification 0 (DMAPCellID0), offset 0xFF0 ........................................... 670 DMA PrimeCell Identification 1 (DMAPCellID1), offset 0xFF4 ........................................... 671 DMA PrimeCell Identification 2 (DMAPCellID2), offset 0xFF8 ........................................... 672 DMA PrimeCell Identification 3 (DMAPCellID3), offset 0xFFC ........................................... 673 General-Purpose Input/Outputs (GPIOs) ................................................................................... 674 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: GPIO Data (GPIODATA), offset 0x000 ............................................................................ 688 GPIO Direction (GPIODIR), offset 0x400 ......................................................................... 690 GPIO Interrupt Sense (GPIOIS), offset 0x404 .................................................................. 691 GPIO Interrupt Both Edges (GPIOIBE), offset 0x408 ........................................................ 692 GPIO Interrupt Event (GPIOIEV), offset 0x40C ................................................................ 693 GPIO Interrupt Mask (GPIOIM), offset 0x410 ................................................................... 694 GPIO Raw Interrupt Status (GPIORIS), offset 0x414 ........................................................ 695 GPIO Masked Interrupt Status (GPIOMIS), offset 0x418 ................................................... 696 GPIO Interrupt Clear (GPIOICR), offset 0x41C ................................................................ 697 GPIO Alternate Function Select (GPIOAFSEL), offset 0x420 ............................................ 698 GPIO 2-mA Drive Select (GPIODR2R), offset 0x500 ........................................................ 700 GPIO 4-mA Drive Select (GPIODR4R), offset 0x504 ........................................................ 701 GPIO 8-mA Drive Select (GPIODR8R), offset 0x508 ........................................................ 702 GPIO Open Drain Select (GPIOODR), offset 0x50C ......................................................... 704 GPIO Pull-Up Select (GPIOPUR), offset 0x510 ................................................................ 705 GPIO Pull-Down Select (GPIOPDR), offset 0x514 ........................................................... 707 GPIO Slew Rate Control Select (GPIOSLR), offset 0x518 ................................................ 709 GPIO Digital Enable (GPIODEN), offset 0x51C ................................................................ 710 GPIO Lock (GPIOLOCK), offset 0x520 ............................................................................ 712 GPIO Commit (GPIOCR), offset 0x524 ............................................................................ 713 GPIO Analog Mode Select (GPIOAMSEL), offset 0x528 ................................................... 715 GPIO Port Control (GPIOPCTL), offset 0x52C ................................................................. 717 GPIO ADC Control (GPIOADCCTL), offset 0x530 ............................................................ 719 GPIO DMA Control (GPIODMACTL), offset 0x534 ........................................................... 720 GPIO Select Interrupt (GPIOSI), offset 0x538 .................................................................. 721 GPIO Peripheral Identification 4 (GPIOPeriphID4), offset 0xFD0 ....................................... 722 GPIO Peripheral Identification 5 (GPIOPeriphID5), offset 0xFD4 ....................................... 723 GPIO Peripheral Identification 6 (GPIOPeriphID6), offset 0xFD8 ....................................... 724 GPIO Peripheral Identification 7 (GPIOPeriphID7), offset 0xFDC ...................................... 725 GPIO Peripheral Identification 0 (GPIOPeriphID0), offset 0xFE0 ....................................... 726 GPIO Peripheral Identification 1 (GPIOPeriphID1), offset 0xFE4 ....................................... 727 GPIO Peripheral Identification 2 (GPIOPeriphID2), offset 0xFE8 ....................................... 728 GPIO Peripheral Identification 3 (GPIOPeriphID3), offset 0xFEC ...................................... 729 GPIO PrimeCell Identification 0 (GPIOPCellID0), offset 0xFF0 .......................................... 730 26 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 35: Register 36: Register 37: GPIO PrimeCell Identification 1 (GPIOPCellID1), offset 0xFF4 .......................................... 731 GPIO PrimeCell Identification 2 (GPIOPCellID2), offset 0xFF8 .......................................... 732 GPIO PrimeCell Identification 3 (GPIOPCellID3), offset 0xFFC ......................................... 733 General-Purpose Timers ............................................................................................................. 734 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: GPTM Configuration (GPTMCFG), offset 0x000 .............................................................. 758 GPTM Timer A Mode (GPTMTAMR), offset 0x004 ........................................................... 760 GPTM Timer B Mode (GPTMTBMR), offset 0x008 ........................................................... 764 GPTM Control (GPTMCTL), offset 0x00C ........................................................................ 768 GPTM Synchronize (GPTMSYNC), offset 0x010 .............................................................. 771 GPTM Interrupt Mask (GPTMIMR), offset 0x018 .............................................................. 775 GPTM Raw Interrupt Status (GPTMRIS), offset 0x01C ..................................................... 778 GPTM Masked Interrupt Status (GPTMMIS), offset 0x020 ................................................ 781 GPTM Interrupt Clear (GPTMICR), offset 0x024 .............................................................. 784 GPTM Timer A Interval Load (GPTMTAILR), offset 0x028 ................................................ 786 GPTM Timer B Interval Load (GPTMTBILR), offset 0x02C ................................................ 787 GPTM Timer A Match (GPTMTAMATCHR), offset 0x030 .................................................. 788 GPTM Timer B Match (GPTMTBMATCHR), offset 0x034 ................................................. 789 GPTM Timer A Prescale (GPTMTAPR), offset 0x038 ....................................................... 790 GPTM Timer B Prescale (GPTMTBPR), offset 0x03C ...................................................... 791 GPTM TimerA Prescale Match (GPTMTAPMR), offset 0x040 ........................................... 792 GPTM TimerB Prescale Match (GPTMTBPMR), offset 0x044 ........................................... 793 GPTM Timer A (GPTMTAR), offset 0x048 ....................................................................... 794 GPTM Timer B (GPTMTBR), offset 0x04C ....................................................................... 795 GPTM Timer A Value (GPTMTAV), offset 0x050 ............................................................... 796 GPTM Timer B Value (GPTMTBV), offset 0x054 .............................................................. 797 GPTM RTC Predivide (GPTMRTCPD), offset 0x058 ........................................................ 798 GPTM Timer A Prescale Snapshot (GPTMTAPS), offset 0x05C ........................................ 799 GPTM Timer B Prescale Snapshot (GPTMTBPS), offset 0x060 ........................................ 800 GPTM Timer A Prescale Value (GPTMTAPV), offset 0x064 .............................................. 801 GPTM Timer B Prescale Value (GPTMTBPV), offset 0x068 .............................................. 802 GPTM Peripheral Properties (GPTMPP), offset 0xFC0 ..................................................... 803 Watchdog Timers ......................................................................................................................... 804 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Watchdog Load (WDTLOAD), offset 0x000 ...................................................................... 808 Watchdog Value (WDTVALUE), offset 0x004 ................................................................... 809 Watchdog Control (WDTCTL), offset 0x008 ..................................................................... 810 Watchdog Interrupt Clear (WDTICR), offset 0x00C .......................................................... 812 Watchdog Raw Interrupt Status (WDTRIS), offset 0x010 .................................................. 813 Watchdog Masked Interrupt Status (WDTMIS), offset 0x014 ............................................. 814 Watchdog Test (WDTTEST), offset 0x418 ....................................................................... 815 Watchdog Lock (WDTLOCK), offset 0xC00 ..................................................................... 816 Watchdog Peripheral Identification 4 (WDTPeriphID4), offset 0xFD0 ................................. 817 Watchdog Peripheral Identification 5 (WDTPeriphID5), offset 0xFD4 ................................. 818 Watchdog Peripheral Identification 6 (WDTPeriphID6), offset 0xFD8 ................................. 819 Watchdog Peripheral Identification 7 (WDTPeriphID7), offset 0xFDC ................................ 820 Watchdog Peripheral Identification 0 (WDTPeriphID0), offset 0xFE0 ................................. 821 Watchdog Peripheral Identification 1 (WDTPeriphID1), offset 0xFE4 ................................. 822 Watchdog Peripheral Identification 2 (WDTPeriphID2), offset 0xFE8 ................................. 823 Watchdog Peripheral Identification 3 (WDTPeriphID3), offset 0xFEC ................................. 824 November 08, 2011 27 Texas Instruments-Advance Information Table of Contents Register 17: Register 18: Register 19: Register 20: Watchdog PrimeCell Identification 0 (WDTPCellID0), offset 0xFF0 .................................... Watchdog PrimeCell Identification 1 (WDTPCellID1), offset 0xFF4 .................................... Watchdog PrimeCell Identification 2 (WDTPCellID2), offset 0xFF8 .................................... Watchdog PrimeCell Identification 3 (WDTPCellID3 ), offset 0xFFC .................................. 825 826 827 828 Analog-to-Digital Converter (ADC) ............................................................................................. 829 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: Register 36: Register 37: Register 38: Register 39: Register 40: ADC Active Sample Sequencer (ADCACTSS), offset 0x000 ............................................. 850 ADC Raw Interrupt Status (ADCRIS), offset 0x004 ........................................................... 851 ADC Interrupt Mask (ADCIM), offset 0x008 ..................................................................... 853 ADC Interrupt Status and Clear (ADCISC), offset 0x00C .................................................. 855 ADC Overflow Status (ADCOSTAT), offset 0x010 ............................................................ 858 ADC Event Multiplexer Select (ADCEMUX), offset 0x014 ................................................. 860 ADC Underflow Status (ADCUSTAT), offset 0x018 ........................................................... 865 ADC Trigger Source Select (ADCTSSEL), offset 0x01C ................................................... 866 ADC Sample Sequencer Priority (ADCSSPRI), offset 0x020 ............................................. 868 ADC Sample Phase Control (ADCSPC), offset 0x024 ...................................................... 870 ADC Processor Sample Sequence Initiate (ADCPSSI), offset 0x028 ................................. 872 ADC Sample Averaging Control (ADCSAC), offset 0x030 ................................................. 874 ADC Digital Comparator Interrupt Status and Clear (ADCDCISC), offset 0x034 ................. 875 ADC Control (ADCCTL), offset 0x038 ............................................................................. 877 ADC Sample Sequence Input Multiplexer Select 0 (ADCSSMUX0), offset 0x040 ............... 878 ADC Sample Sequence Control 0 (ADCSSCTL0), offset 0x044 ........................................ 880 ADC Sample Sequence Result FIFO 0 (ADCSSFIFO0), offset 0x048 ................................ 883 ADC Sample Sequence Result FIFO 1 (ADCSSFIFO1), offset 0x068 ................................ 883 ADC Sample Sequence Result FIFO 2 (ADCSSFIFO2), offset 0x088 ................................ 883 ADC Sample Sequence Result FIFO 3 (ADCSSFIFO3), offset 0x0A8 ............................... 883 ADC Sample Sequence FIFO 0 Status (ADCSSFSTAT0), offset 0x04C ............................. 884 ADC Sample Sequence FIFO 1 Status (ADCSSFSTAT1), offset 0x06C ............................. 884 ADC Sample Sequence FIFO 2 Status (ADCSSFSTAT2), offset 0x08C ............................ 884 ADC Sample Sequence FIFO 3 Status (ADCSSFSTAT3), offset 0x0AC ............................ 884 ADC Sample Sequence 0 Operation (ADCSSOP0), offset 0x050 ...................................... 886 ADC Sample Sequence 0 Digital Comparator Select (ADCSSDC0), offset 0x054 .............. 888 ADC Sample Sequence Extended Input Multiplexer Select 0 (ADCSSEMUX0), offset 0x058 ........................................................................................................................... 890 ADC Sample Sequence Input Multiplexer Select 1 (ADCSSMUX1), offset 0x060 ............... 892 ADC Sample Sequence Input Multiplexer Select 2 (ADCSSMUX2), offset 0x080 ............... 892 ADC Sample Sequence Control 1 (ADCSSCTL1), offset 0x064 ........................................ 893 ADC Sample Sequence Control 2 (ADCSSCTL2), offset 0x084 ........................................ 893 ADC Sample Sequence 1 Operation (ADCSSOP1), offset 0x070 ...................................... 895 ADC Sample Sequence 2 Operation (ADCSSOP2), offset 0x090 ..................................... 895 ADC Sample Sequence 1 Digital Comparator Select (ADCSSDC1), offset 0x074 .............. 896 ADC Sample Sequence 2 Digital Comparator Select (ADCSSDC2), offset 0x094 .............. 896 ADC Sample Sequence Extended Input Multiplexer Select 1 (ADCSSEMUX1), offset 0x078 ........................................................................................................................... 898 ADC Sample Sequence Extended Input Multiplexer Select 2 (ADCSSEMUX2), offset 0x098 ..................................................................................................................................... 898 ADC Sample Sequence Input Multiplexer Select 3 (ADCSSMUX3), offset 0x0A0 ............... 900 ADC Sample Sequence Control 3 (ADCSSCTL3), offset 0x0A4 ........................................ 901 ADC Sample Sequence 3 Operation (ADCSSOP3), offset 0x0B0 ..................................... 902 28 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 41: Register 42: Register 43: Register 44: Register 45: Register 46: Register 47: Register 48: Register 49: Register 50: Register 51: Register 52: Register 53: Register 54: Register 55: Register 56: Register 57: Register 58: Register 59: Register 60: Register 61: Register 62: ADC Sample Sequence 3 Digital Comparator Select (ADCSSDC3), offset 0x0B4 .............. 903 ADC Sample Sequence Extended Input Multiplexer Select 3 (ADCSSEMUX3), offset 0x0B8 ........................................................................................................................... 904 ADC Digital Comparator Reset Initial Conditions (ADCDCRIC), offset 0xD00 ..................... 905 ADC Digital Comparator Control 0 (ADCDCCTL0), offset 0xE00 ....................................... 910 ADC Digital Comparator Control 1 (ADCDCCTL1), offset 0xE04 ....................................... 910 ADC Digital Comparator Control 2 (ADCDCCTL2), offset 0xE08 ....................................... 910 ADC Digital Comparator Control 3 (ADCDCCTL3), offset 0xE0C ...................................... 910 ADC Digital Comparator Control 4 (ADCDCCTL4), offset 0xE10 ....................................... 910 ADC Digital Comparator Control 5 (ADCDCCTL5), offset 0xE14 ....................................... 910 ADC Digital Comparator Control 6 (ADCDCCTL6), offset 0xE18 ....................................... 910 ADC Digital Comparator Control 7 (ADCDCCTL7), offset 0xE1C ...................................... 910 ADC Digital Comparator Range 0 (ADCDCCMP0), offset 0xE40 ....................................... 913 ADC Digital Comparator Range 1 (ADCDCCMP1), offset 0xE44 ....................................... 913 ADC Digital Comparator Range 2 (ADCDCCMP2), offset 0xE48 ....................................... 913 ADC Digital Comparator Range 3 (ADCDCCMP3), offset 0xE4C ...................................... 913 ADC Digital Comparator Range 4 (ADCDCCMP4), offset 0xE50 ....................................... 913 ADC Digital Comparator Range 5 (ADCDCCMP5), offset 0xE54 ....................................... 913 ADC Digital Comparator Range 6 (ADCDCCMP6), offset 0xE58 ....................................... 913 ADC Digital Comparator Range 7 (ADCDCCMP7), offset 0xE5C ...................................... 913 ADC Peripheral Properties (ADCPP), offset 0xFC0 .......................................................... 914 ADC Peripheral Configuration (ADCPC), offset 0xFC4 ..................................................... 916 ADC Clock Configuration (ADCCC), offset 0xFC8 ............................................................ 917 Universal Asynchronous Receivers/Transmitters (UARTs) ..................................................... 918 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: UART Data (UARTDR), offset 0x000 ............................................................................... 932 UART Receive Status/Error Clear (UARTRSR/UARTECR), offset 0x004 ........................... 934 UART Flag (UARTFR), offset 0x018 ................................................................................ 937 UART IrDA Low-Power Register (UARTILPR), offset 0x020 ............................................. 940 UART Integer Baud-Rate Divisor (UARTIBRD), offset 0x024 ............................................ 941 UART Fractional Baud-Rate Divisor (UARTFBRD), offset 0x028 ....................................... 942 UART Line Control (UARTLCRH), offset 0x02C ............................................................... 943 UART Control (UARTCTL), offset 0x030 ......................................................................... 945 UART Interrupt FIFO Level Select (UARTIFLS), offset 0x034 ........................................... 949 UART Interrupt Mask (UARTIM), offset 0x038 ................................................................. 951 UART Raw Interrupt Status (UARTRIS), offset 0x03C ...................................................... 955 UART Masked Interrupt Status (UARTMIS), offset 0x040 ................................................. 959 UART Interrupt Clear (UARTICR), offset 0x044 ............................................................... 963 UART DMA Control (UARTDMACTL), offset 0x048 .......................................................... 965 UART LIN Control (UARTLCTL), offset 0x090 ................................................................. 966 UART LIN Snap Shot (UARTLSS), offset 0x094 ............................................................... 967 UART LIN Timer (UARTLTIM), offset 0x098 ..................................................................... 968 UART 9-Bit Self Address (UART9BITADDR), offset 0x0A4 ............................................... 969 UART 9-Bit Self Address Mask (UART9BITAMASK), offset 0x0A8 .................................... 970 UART Peripheral Properties (UARTPP), offset 0xFC0 ...................................................... 971 UART Clock Configuration (UARTCC), offset 0xFC8 ........................................................ 972 UART Peripheral Identification 4 (UARTPeriphID4), offset 0xFD0 ..................................... 973 UART Peripheral Identification 5 (UARTPeriphID5), offset 0xFD4 ..................................... 974 UART Peripheral Identification 6 (UARTPeriphID6), offset 0xFD8 ..................................... 975 November 08, 2011 29 Texas Instruments-Advance Information Table of Contents Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: UART Peripheral Identification 7 (UARTPeriphID7), offset 0xFDC ..................................... UART Peripheral Identification 0 (UARTPeriphID0), offset 0xFE0 ...................................... UART Peripheral Identification 1 (UARTPeriphID1), offset 0xFE4 ...................................... UART Peripheral Identification 2 (UARTPeriphID2), offset 0xFE8 ...................................... UART Peripheral Identification 3 (UARTPeriphID3), offset 0xFEC ..................................... UART PrimeCell Identification 0 (UARTPCellID0), offset 0xFF0 ........................................ UART PrimeCell Identification 1 (UARTPCellID1), offset 0xFF4 ........................................ UART PrimeCell Identification 2 (UARTPCellID2), offset 0xFF8 ........................................ UART PrimeCell Identification 3 (UARTPCellID3), offset 0xFFC ........................................ 976 977 978 979 980 981 982 983 984 Synchronous Serial Interface (SSI) ............................................................................................ 985 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: SSI Control 0 (SSICR0), offset 0x000 ............................................................................ 1000 SSI Control 1 (SSICR1), offset 0x004 ............................................................................ 1002 SSI Data (SSIDR), offset 0x008 .................................................................................... 1004 SSI Status (SSISR), offset 0x00C ................................................................................. 1005 SSI Clock Prescale (SSICPSR), offset 0x010 ................................................................ 1007 SSI Interrupt Mask (SSIIM), offset 0x014 ....................................................................... 1008 SSI Raw Interrupt Status (SSIRIS), offset 0x018 ............................................................ 1009 SSI Masked Interrupt Status (SSIMIS), offset 0x01C ...................................................... 1011 SSI Interrupt Clear (SSIICR), offset 0x020 ..................................................................... 1013 SSI DMA Control (SSIDMACTL), offset 0x024 ............................................................... 1014 SSI Clock Configuration (SSICC), offset 0xFC8 ............................................................. 1015 SSI Peripheral Identification 4 (SSIPeriphID4), offset 0xFD0 ........................................... 1016 SSI Peripheral Identification 5 (SSIPeriphID5), offset 0xFD4 ........................................... 1017 SSI Peripheral Identification 6 (SSIPeriphID6), offset 0xFD8 ........................................... 1018 SSI Peripheral Identification 7 (SSIPeriphID7), offset 0xFDC .......................................... 1019 SSI Peripheral Identification 0 (SSIPeriphID0), offset 0xFE0 ........................................... 1020 SSI Peripheral Identification 1 (SSIPeriphID1), offset 0xFE4 ........................................... 1021 SSI Peripheral Identification 2 (SSIPeriphID2), offset 0xFE8 ........................................... 1022 SSI Peripheral Identification 3 (SSIPeriphID3), offset 0xFEC .......................................... 1023 SSI PrimeCell Identification 0 (SSIPCellID0), offset 0xFF0 .............................................. 1024 SSI PrimeCell Identification 1 (SSIPCellID1), offset 0xFF4 .............................................. 1025 SSI PrimeCell Identification 2 (SSIPCellID2), offset 0xFF8 .............................................. 1026 SSI PrimeCell Identification 3 (SSIPCellID3), offset 0xFFC ............................................. 1027 Inter-Integrated Circuit (I2C) Interface ...................................................................................... 1028 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: I2C Master Slave Address (I2CMSA), offset 0x000 ......................................................... 1046 I2C Master Control/Status (I2CMCS), offset 0x004 ......................................................... 1047 I2C Master Data (I2CMDR), offset 0x008 ....................................................................... 1052 I2C Master Timer Period (I2CMTPR), offset 0x00C ......................................................... 1053 I2C Master Interrupt Mask (I2CMIMR), offset 0x010 ....................................................... 1054 I2C Master Raw Interrupt Status (I2CMRIS), offset 0x014 ............................................... 1055 I2C Master Masked Interrupt Status (I2CMMIS), offset 0x018 .......................................... 1056 I2C Master Interrupt Clear (I2CMICR), offset 0x01C ....................................................... 1057 I2C Master Configuration (I2CMCR), offset 0x020 .......................................................... 1058 I2C Master Clock Low Timeout Count (I2CMCLKOCNT), offset 0x024 ............................. 1059 I2C Master Bus Monitor (I2CMBMON), offset 0x02C ....................................................... 1060 I2C Slave Own Address (I2CSOAR), offset 0x800 .......................................................... 1061 I2C Slave Control/Status (I2CSCSR), offset 0x804 ......................................................... 1062 30 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: I2C Slave Data (I2CSDR), offset 0x808 ......................................................................... 1064 I2C Slave Interrupt Mask (I2CSIMR), offset 0x80C ......................................................... 1065 I2C Slave Raw Interrupt Status (I2CSRIS), offset 0x810 ................................................. 1066 I2C Slave Masked Interrupt Status (I2CSMIS), offset 0x814 ............................................ 1067 I2C Slave Interrupt Clear (I2CSICR), offset 0x818 .......................................................... 1068 I2C Slave Own Address 2 (I2CSOAR2), offset 0x81C ..................................................... 1069 I2C Slave ACK Control (I2CSACKCTL), offset 0x820 ...................................................... 1070 I2C Peripheral Properties (I2CPP), offset 0xFC0 ............................................................ 1071 I2C Peripheral Configuration (I2CPC), offset 0xFC4 ....................................................... 1072 Controller Area Network (CAN) Module ................................................................................... 1073 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: Register 36: Register 37: CAN Control (CANCTL), offset 0x000 ............................................................................ 1095 CAN Status (CANSTS), offset 0x004 ............................................................................. 1097 CAN Error Counter (CANERR), offset 0x008 ................................................................. 1100 CAN Bit Timing (CANBIT), offset 0x00C ........................................................................ 1101 CAN Interrupt (CANINT), offset 0x010 ........................................................................... 1102 CAN Test (CANTST), offset 0x014 ................................................................................ 1103 CAN Baud Rate Prescaler Extension (CANBRPE), offset 0x018 ..................................... 1105 CAN IF1 Command Request (CANIF1CRQ), offset 0x020 .............................................. 1106 CAN IF2 Command Request (CANIF2CRQ), offset 0x080 .............................................. 1106 CAN IF1 Command Mask (CANIF1CMSK), offset 0x024 ................................................ 1107 CAN IF2 Command Mask (CANIF2CMSK), offset 0x084 ................................................ 1107 CAN IF1 Mask 1 (CANIF1MSK1), offset 0x028 .............................................................. 1110 CAN IF2 Mask 1 (CANIF2MSK1), offset 0x088 .............................................................. 1110 CAN IF1 Mask 2 (CANIF1MSK2), offset 0x02C .............................................................. 1111 CAN IF2 Mask 2 (CANIF2MSK2), offset 0x08C .............................................................. 1111 CAN IF1 Arbitration 1 (CANIF1ARB1), offset 0x030 ....................................................... 1113 CAN IF2 Arbitration 1 (CANIF2ARB1), offset 0x090 ....................................................... 1113 CAN IF1 Arbitration 2 (CANIF1ARB2), offset 0x034 ....................................................... 1114 CAN IF2 Arbitration 2 (CANIF2ARB2), offset 0x094 ....................................................... 1114 CAN IF1 Message Control (CANIF1MCTL), offset 0x038 ................................................ 1116 CAN IF2 Message Control (CANIF2MCTL), offset 0x098 ................................................ 1116 CAN IF1 Data A1 (CANIF1DA1), offset 0x03C ............................................................... 1119 CAN IF1 Data A2 (CANIF1DA2), offset 0x040 ................................................................ 1119 CAN IF1 Data B1 (CANIF1DB1), offset 0x044 ................................................................ 1119 CAN IF1 Data B2 (CANIF1DB2), offset 0x048 ................................................................ 1119 CAN IF2 Data A1 (CANIF2DA1), offset 0x09C ............................................................... 1119 CAN IF2 Data A2 (CANIF2DA2), offset 0x0A0 ............................................................... 1119 CAN IF2 Data B1 (CANIF2DB1), offset 0x0A4 ............................................................... 1119 CAN IF2 Data B2 (CANIF2DB2), offset 0x0A8 ............................................................... 1119 CAN Transmission Request 1 (CANTXRQ1), offset 0x100 .............................................. 1120 CAN Transmission Request 2 (CANTXRQ2), offset 0x104 .............................................. 1120 CAN New Data 1 (CANNWDA1), offset 0x120 ............................................................... 1121 CAN New Data 2 (CANNWDA2), offset 0x124 ............................................................... 1121 CAN Message 1 Interrupt Pending (CANMSG1INT), offset 0x140 ................................... 1122 CAN Message 2 Interrupt Pending (CANMSG2INT), offset 0x144 ................................... 1122 CAN Message 1 Valid (CANMSG1VAL), offset 0x160 ..................................................... 1123 CAN Message 2 Valid (CANMSG2VAL), offset 0x164 ..................................................... 1123 November 08, 2011 31 Texas Instruments-Advance Information Table of Contents Universal Serial Bus (USB) Controller ..................................................................................... 1124 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: Register 36: Register 37: Register 38: Register 39: Register 40: Register 41: Register 42: Register 43: Register 44: Register 45: Register 46: Register 47: USB Device Functional Address (USBFADDR), offset 0x000 .......................................... 1146 USB Power (USBPOWER), offset 0x001 ....................................................................... 1147 USB Transmit Interrupt Status (USBTXIS), offset 0x002 ................................................. 1150 USB Receive Interrupt Status (USBRXIS), offset 0x004 ................................................. 1152 USB Transmit Interrupt Enable (USBTXIE), offset 0x006 ................................................ 1153 USB Receive Interrupt Enable (USBRXIE), offset 0x008 ................................................. 1155 USB General Interrupt Status (USBIS), offset 0x00A ...................................................... 1156 USB Interrupt Enable (USBIE), offset 0x00B .................................................................. 1159 USB Frame Value (USBFRAME), offset 0x00C .............................................................. 1162 USB Endpoint Index (USBEPIDX), offset 0x00E ............................................................ 1163 USB Test Mode (USBTEST), offset 0x00F ..................................................................... 1164 USB FIFO Endpoint 0 (USBFIFO0), offset 0x020 ........................................................... 1166 USB FIFO Endpoint 1 (USBFIFO1), offset 0x024 ........................................................... 1166 USB FIFO Endpoint 2 (USBFIFO2), offset 0x028 ........................................................... 1166 USB FIFO Endpoint 3 (USBFIFO3), offset 0x02C ........................................................... 1166 USB FIFO Endpoint 4 (USBFIFO4), offset 0x030 ........................................................... 1166 USB FIFO Endpoint 5 (USBFIFO5), offset 0x034 ........................................................... 1166 USB FIFO Endpoint 6 (USBFIFO6), offset 0x038 ........................................................... 1166 USB FIFO Endpoint 7 (USBFIFO7), offset 0x03C ........................................................... 1166 USB Device Control (USBDEVCTL), offset 0x060 .......................................................... 1167 USB Transmit Dynamic FIFO Sizing (USBTXFIFOSZ), offset 0x062 ................................ 1169 USB Receive Dynamic FIFO Sizing (USBRXFIFOSZ), offset 0x063 ................................ 1169 USB Transmit FIFO Start Address (USBTXFIFOADD), offset 0x064 ................................ 1170 USB Receive FIFO Start Address (USBRXFIFOADD), offset 0x066 ................................ 1170 USB Connect Timing (USBCONTIM), offset 0x07A ........................................................ 1171 USB OTG VBUS Pulse Timing (USBVPLEN), offset 0x07B ............................................ 1172 USB Full-Speed Last Transaction to End of Frame Timing (USBFSEOF), offset 0x07D .... 1173 USB Low-Speed Last Transaction to End of Frame Timing (USBLSEOF), offset 0x07E .... 1174 USB Transmit Functional Address Endpoint 0 (USBTXFUNCADDR0), offset 0x080 ......... 1175 USB Transmit Functional Address Endpoint 1 (USBTXFUNCADDR1), offset 0x088 ......... 1175 USB Transmit Functional Address Endpoint 2 (USBTXFUNCADDR2), offset 0x090 ......... 1175 USB Transmit Functional Address Endpoint 3 (USBTXFUNCADDR3), offset 0x098 ......... 1175 USB Transmit Functional Address Endpoint 4 (USBTXFUNCADDR4), offset 0x0A0 ......... 1175 USB Transmit Functional Address Endpoint 5 (USBTXFUNCADDR5), offset 0x0A8 ......... 1175 USB Transmit Functional Address Endpoint 6 (USBTXFUNCADDR6), offset 0x0B0 ......... 1175 USB Transmit Functional Address Endpoint 7 (USBTXFUNCADDR7), offset 0x0B8 ......... 1175 USB Transmit Hub Address Endpoint 0 (USBTXHUBADDR0), offset 0x082 ..................... 1176 USB Transmit Hub Address Endpoint 1 (USBTXHUBADDR1), offset 0x08A .................... 1176 USB Transmit Hub Address Endpoint 2 (USBTXHUBADDR2), offset 0x092 ..................... 1176 USB Transmit Hub Address Endpoint 3 (USBTXHUBADDR3), offset 0x09A .................... 1176 USB Transmit Hub Address Endpoint 4 (USBTXHUBADDR4), offset 0x0A2 .................... 1176 USB Transmit Hub Address Endpoint 5 (USBTXHUBADDR5), offset 0x0AA .................... 1176 USB Transmit Hub Address Endpoint 6 (USBTXHUBADDR6), offset 0x0B2 .................... 1176 USB Transmit Hub Address Endpoint 7 (USBTXHUBADDR7), offset 0x0BA .................... 1176 USB Transmit Hub Port Endpoint 0 (USBTXHUBPORT0), offset 0x083 ........................... 1177 USB Transmit Hub Port Endpoint 1 (USBTXHUBPORT1), offset 0x08B ........................... 1177 USB Transmit Hub Port Endpoint 2 (USBTXHUBPORT2), offset 0x093 ........................... 1177 32 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 48: Register 49: Register 50: Register 51: Register 52: Register 53: Register 54: Register 55: Register 56: Register 57: Register 58: Register 59: Register 60: Register 61: Register 62: Register 63: Register 64: Register 65: Register 66: Register 67: Register 68: Register 69: Register 70: Register 71: Register 72: Register 73: Register 74: Register 75: Register 76: Register 77: Register 78: Register 79: Register 80: Register 81: Register 82: Register 83: Register 84: Register 85: Register 86: Register 87: Register 88: Register 89: Register 90: Register 91: Register 92: Register 93: Register 94: Register 95: USB Transmit Hub Port Endpoint 3 (USBTXHUBPORT3), offset 0x09B ........................... 1177 USB Transmit Hub Port Endpoint 4 (USBTXHUBPORT4), offset 0x0A3 ........................... 1177 USB Transmit Hub Port Endpoint 5 (USBTXHUBPORT5), offset 0x0AB .......................... 1177 USB Transmit Hub Port Endpoint 6 (USBTXHUBPORT6), offset 0x0B3 ........................... 1177 USB Transmit Hub Port Endpoint 7 (USBTXHUBPORT7), offset 0x0BB .......................... 1177 USB Receive Functional Address Endpoint 1 (USBRXFUNCADDR1), offset 0x08C ......... 1178 USB Receive Functional Address Endpoint 2 (USBRXFUNCADDR2), offset 0x094 ......... 1178 USB Receive Functional Address Endpoint 3 (USBRXFUNCADDR3), offset 0x09C ......... 1178 USB Receive Functional Address Endpoint 4 (USBRXFUNCADDR4), offset 0x0A4 ......... 1178 USB Receive Functional Address Endpoint 5 (USBRXFUNCADDR5), offset 0x0AC ......... 1178 USB Receive Functional Address Endpoint 6 (USBRXFUNCADDR6), offset 0x0B4 ......... 1178 USB Receive Functional Address Endpoint 7 (USBRXFUNCADDR7), offset 0x0BC ......... 1178 USB Receive Hub Address Endpoint 1 (USBRXHUBADDR1), offset 0x08E ..................... 1179 USB Receive Hub Address Endpoint 2 (USBRXHUBADDR2), offset 0x096 ..................... 1179 USB Receive Hub Address Endpoint 3 (USBRXHUBADDR3), offset 0x09E ..................... 1179 USB Receive Hub Address Endpoint 4 (USBRXHUBADDR4), offset 0x0A6 ..................... 1179 USB Receive Hub Address Endpoint 5 (USBRXHUBADDR5), offset 0x0AE .................... 1179 USB Receive Hub Address Endpoint 6 (USBRXHUBADDR6), offset 0x0B6 ..................... 1179 USB Receive Hub Address Endpoint 7 (USBRXHUBADDR7), offset 0x0BE .................... 1179 USB Receive Hub Port Endpoint 1 (USBRXHUBPORT1), offset 0x08F ........................... 1180 USB Receive Hub Port Endpoint 2 (USBRXHUBPORT2), offset 0x097 ........................... 1180 USB Receive Hub Port Endpoint 3 (USBRXHUBPORT3), offset 0x09F ........................... 1180 USB Receive Hub Port Endpoint 4 (USBRXHUBPORT4), offset 0x0A7 ........................... 1180 USB Receive Hub Port Endpoint 5 (USBRXHUBPORT5), offset 0x0AF ........................... 1180 USB Receive Hub Port Endpoint 6 (USBRXHUBPORT6), offset 0x0B7 ........................... 1180 USB Receive Hub Port Endpoint 7 (USBRXHUBPORT7), offset 0x0BF ........................... 1180 USB Maximum Transmit Data Endpoint 1 (USBTXMAXP1), offset 0x110 ......................... 1181 USB Maximum Transmit Data Endpoint 2 (USBTXMAXP2), offset 0x120 ........................ 1181 USB Maximum Transmit Data Endpoint 3 (USBTXMAXP3), offset 0x130 ........................ 1181 USB Maximum Transmit Data Endpoint 4 (USBTXMAXP4), offset 0x140 ........................ 1181 USB Maximum Transmit Data Endpoint 5 (USBTXMAXP5), offset 0x150 ........................ 1181 USB Maximum Transmit Data Endpoint 6 (USBTXMAXP6), offset 0x160 ........................ 1181 USB Maximum Transmit Data Endpoint 7 (USBTXMAXP7), offset 0x170 ........................ 1181 USB Control and Status Endpoint 0 Low (USBCSRL0), offset 0x102 ............................... 1182 USB Control and Status Endpoint 0 High (USBCSRH0), offset 0x103 ............................. 1186 USB Receive Byte Count Endpoint 0 (USBCOUNT0), offset 0x108 ................................. 1188 USB Type Endpoint 0 (USBTYPE0), offset 0x10A .......................................................... 1189 USB NAK Limit (USBNAKLMT), offset 0x10B ................................................................ 1190 USB Transmit Control and Status Endpoint 1 Low (USBTXCSRL1), offset 0x112 ............. 1191 USB Transmit Control and Status Endpoint 2 Low (USBTXCSRL2), offset 0x122 ............. 1191 USB Transmit Control and Status Endpoint 3 Low (USBTXCSRL3), offset 0x132 ............. 1191 USB Transmit Control and Status Endpoint 4 Low (USBTXCSRL4), offset 0x142 ............. 1191 USB Transmit Control and Status Endpoint 5 Low (USBTXCSRL5), offset 0x152 ............. 1191 USB Transmit Control and Status Endpoint 6 Low (USBTXCSRL6), offset 0x162 ............. 1191 USB Transmit Control and Status Endpoint 7 Low (USBTXCSRL7), offset 0x172 ............. 1191 USB Transmit Control and Status Endpoint 1 High (USBTXCSRH1), offset 0x113 ............ 1195 USB Transmit Control and Status Endpoint 2 High (USBTXCSRH2), offset 0x123 ........... 1195 USB Transmit Control and Status Endpoint 3 High (USBTXCSRH3), offset 0x133 ........... 1195 November 08, 2011 33 Texas Instruments-Advance Information Table of Contents Register 96: Register 97: Register 98: Register 99: Register 100: Register 101: Register 102: Register 103: Register 104: Register 105: Register 106: Register 107: Register 108: Register 109: Register 110: Register 111: Register 112: Register 113: Register 114: Register 115: Register 116: Register 117: Register 118: Register 119: Register 120: Register 121: Register 122: Register 123: Register 124: Register 125: Register 126: Register 127: Register 128: Register 129: Register 130: Register 131: Register 132: Register 133: Register 134: Register 135: Register 136: Register 137: Register 138: Register 139: Register 140: Register 141: Register 142: Register 143: USB Transmit Control and Status Endpoint 4 High (USBTXCSRH4), offset 0x143 ........... 1195 USB Transmit Control and Status Endpoint 5 High (USBTXCSRH5), offset 0x153 ........... 1195 USB Transmit Control and Status Endpoint 6 High (USBTXCSRH6), offset 0x163 ........... 1195 USB Transmit Control and Status Endpoint 7 High (USBTXCSRH7), offset 0x173 ........... 1195 USB Maximum Receive Data Endpoint 1 (USBRXMAXP1), offset 0x114 ......................... 1199 USB Maximum Receive Data Endpoint 2 (USBRXMAXP2), offset 0x124 ......................... 1199 USB Maximum Receive Data Endpoint 3 (USBRXMAXP3), offset 0x134 ......................... 1199 USB Maximum Receive Data Endpoint 4 (USBRXMAXP4), offset 0x144 ......................... 1199 USB Maximum Receive Data Endpoint 5 (USBRXMAXP5), offset 0x154 ......................... 1199 USB Maximum Receive Data Endpoint 6 (USBRXMAXP6), offset 0x164 ......................... 1199 USB Maximum Receive Data Endpoint 7 (USBRXMAXP7), offset 0x174 ......................... 1199 USB Receive Control and Status Endpoint 1 Low (USBRXCSRL1), offset 0x116 ............. 1200 USB Receive Control and Status Endpoint 2 Low (USBRXCSRL2), offset 0x126 ............. 1200 USB Receive Control and Status Endpoint 3 Low (USBRXCSRL3), offset 0x136 ............. 1200 USB Receive Control and Status Endpoint 4 Low (USBRXCSRL4), offset 0x146 ............. 1200 USB Receive Control and Status Endpoint 5 Low (USBRXCSRL5), offset 0x156 ............. 1200 USB Receive Control and Status Endpoint 6 Low (USBRXCSRL6), offset 0x166 ............. 1200 USB Receive Control and Status Endpoint 7 Low (USBRXCSRL7), offset 0x176 ............. 1200 USB Receive Control and Status Endpoint 1 High (USBRXCSRH1), offset 0x117 ............ 1205 USB Receive Control and Status Endpoint 2 High (USBRXCSRH2), offset 0x127 ............ 1205 USB Receive Control and Status Endpoint 3 High (USBRXCSRH3), offset 0x137 ............ 1205 USB Receive Control and Status Endpoint 4 High (USBRXCSRH4), offset 0x147 ............ 1205 USB Receive Control and Status Endpoint 5 High (USBRXCSRH5), offset 0x157 ............ 1205 USB Receive Control and Status Endpoint 6 High (USBRXCSRH6), offset 0x167 ............ 1205 USB Receive Control and Status Endpoint 7 High (USBRXCSRH7), offset 0x177 ............ 1205 USB Receive Byte Count Endpoint 1 (USBRXCOUNT1), offset 0x118 ............................. 1209 USB Receive Byte Count Endpoint 2 (USBRXCOUNT2), offset 0x128 ............................ 1209 USB Receive Byte Count Endpoint 3 (USBRXCOUNT3), offset 0x138 ............................ 1209 USB Receive Byte Count Endpoint 4 (USBRXCOUNT4), offset 0x148 ............................ 1209 USB Receive Byte Count Endpoint 5 (USBRXCOUNT5), offset 0x158 ............................ 1209 USB Receive Byte Count Endpoint 6 (USBRXCOUNT6), offset 0x168 ............................ 1209 USB Receive Byte Count Endpoint 7 (USBRXCOUNT7), offset 0x178 ............................ 1209 USB Host Transmit Configure Type Endpoint 1 (USBTXTYPE1), offset 0x11A ................. 1210 USB Host Transmit Configure Type Endpoint 2 (USBTXTYPE2), offset 0x12A ................. 1210 USB Host Transmit Configure Type Endpoint 3 (USBTXTYPE3), offset 0x13A ................. 1210 USB Host Transmit Configure Type Endpoint 4 (USBTXTYPE4), offset 0x14A ................. 1210 USB Host Transmit Configure Type Endpoint 5 (USBTXTYPE5), offset 0x15A ................. 1210 USB Host Transmit Configure Type Endpoint 6 (USBTXTYPE6), offset 0x16A ................. 1210 USB Host Transmit Configure Type Endpoint 7 (USBTXTYPE7), offset 0x17A ................. 1210 USB Host Transmit Interval Endpoint 1 (USBTXINTERVAL1), offset 0x11B ..................... 1212 USB Host Transmit Interval Endpoint 2 (USBTXINTERVAL2), offset 0x12B ..................... 1212 USB Host Transmit Interval Endpoint 3 (USBTXINTERVAL3), offset 0x13B ..................... 1212 USB Host Transmit Interval Endpoint 4 (USBTXINTERVAL4), offset 0x14B ..................... 1212 USB Host Transmit Interval Endpoint 5 (USBTXINTERVAL5), offset 0x15B ..................... 1212 USB Host Transmit Interval Endpoint 6 (USBTXINTERVAL6), offset 0x16B ..................... 1212 USB Host Transmit Interval Endpoint 7 (USBTXINTERVAL7), offset 0x17B ..................... 1212 USB Host Configure Receive Type Endpoint 1 (USBRXTYPE1), offset 0x11C ................. 1213 USB Host Configure Receive Type Endpoint 2 (USBRXTYPE2), offset 0x12C ................. 1213 34 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 144: Register 145: Register 146: Register 147: Register 148: Register 149: Register 150: Register 151: Register 152: Register 153: Register 154: Register 155: Register 156: Register 157: Register 158: Register 159: Register 160: Register 161: Register 162: Register 163: Register 164: Register 165: Register 166: Register 167: Register 168: Register 169: Register 170: Register 171: Register 172: Register 173: Register 174: Register 175: Register 176: Register 177: Register 178: Register 179: Register 180: Register 181: USB Host Configure Receive Type Endpoint 3 (USBRXTYPE3), offset 0x13C ................. 1213 USB Host Configure Receive Type Endpoint 4 (USBRXTYPE4), offset 0x14C ................. 1213 USB Host Configure Receive Type Endpoint 5 (USBRXTYPE5), offset 0x15C ................. 1213 USB Host Configure Receive Type Endpoint 6 (USBRXTYPE6), offset 0x16C ................. 1213 USB Host Configure Receive Type Endpoint 7 (USBRXTYPE7), offset 0x17C ................. 1213 USB Host Receive Polling Interval Endpoint 1 (USBRXINTERVAL1), offset 0x11D ........... 1215 USB Host Receive Polling Interval Endpoint 2 (USBRXINTERVAL2), offset 0x12D ........... 1215 USB Host Receive Polling Interval Endpoint 3 (USBRXINTERVAL3), offset 0x13D ........... 1215 USB Host Receive Polling Interval Endpoint 4 (USBRXINTERVAL4), offset 0x14D ........... 1215 USB Host Receive Polling Interval Endpoint 5 (USBRXINTERVAL5), offset 0x15D ........... 1215 USB Host Receive Polling Interval Endpoint 6 (USBRXINTERVAL6), offset 0x16D ........... 1215 USB Host Receive Polling Interval Endpoint 7 (USBRXINTERVAL7), offset 0x17D ........... 1215 USB Request Packet Count in Block Transfer Endpoint 1 (USBRQPKTCOUNT1), offset 0x304 .......................................................................................................................... 1216 USB Request Packet Count in Block Transfer Endpoint 2 (USBRQPKTCOUNT2), offset 0x308 .......................................................................................................................... 1216 USB Request Packet Count in Block Transfer Endpoint 3 (USBRQPKTCOUNT3), offset 0x30C ......................................................................................................................... 1216 USB Request Packet Count in Block Transfer Endpoint 4 (USBRQPKTCOUNT4), offset 0x310 .......................................................................................................................... 1216 USB Request Packet Count in Block Transfer Endpoint 5 (USBRQPKTCOUNT5), offset 0x314 .......................................................................................................................... 1216 USB Request Packet Count in Block Transfer Endpoint 6 (USBRQPKTCOUNT6), offset 0x318 .......................................................................................................................... 1216 USB Request Packet Count in Block Transfer Endpoint 7 (USBRQPKTCOUNT7), offset 0x31C ......................................................................................................................... 1216 USB Receive Double Packet Buffer Disable (USBRXDPKTBUFDIS), offset 0x340 ........... 1217 USB Transmit Double Packet Buffer Disable (USBTXDPKTBUFDIS), offset 0x342 .......... 1218 USB External Power Control (USBEPC), offset 0x400 .................................................... 1219 USB External Power Control Raw Interrupt Status (USBEPCRIS), offset 0x404 ............... 1222 USB External Power Control Interrupt Mask (USBEPCIM), offset 0x408 .......................... 1223 USB External Power Control Interrupt Status and Clear (USBEPCISC), offset 0x40C ....... 1224 USB Device RESUME Raw Interrupt Status (USBDRRIS), offset 0x410 .......................... 1225 USB Device RESUME Interrupt Mask (USBDRIM), offset 0x414 ..................................... 1226 USB Device RESUME Interrupt Status and Clear (USBDRISC), offset 0x418 .................. 1227 USB General-Purpose Control and Status (USBGPCS), offset 0x41C ............................. 1228 USB VBUS Droop Control (USBVDC), offset 0x430 ....................................................... 1229 USB VBUS Droop Control Raw Interrupt Status (USBVDCRIS), offset 0x434 .................. 1230 USB VBUS Droop Control Interrupt Mask (USBVDCIM), offset 0x438 ............................. 1231 USB VBUS Droop Control Interrupt Status and Clear (USBVDCISC), offset 0x43C .......... 1232 USB ID Valid Detect Raw Interrupt Status (USBIDVRIS), offset 0x444 ............................. 1233 USB ID Valid Detect Interrupt Mask (USBIDVIM), offset 0x448 ........................................ 1234 USB ID Valid Detect Interrupt Status and Clear (USBIDVISC), offset 0x44C .................... 1235 USB DMA Select (USBDMASEL), offset 0x450 .............................................................. 1236 USB Peripheral Properties (USBPP), offset 0xFC0 ........................................................ 1238 Analog Comparators ................................................................................................................. 1239 Register 1: Register 2: Register 3: Analog Comparator Masked Interrupt Status (ACMIS), offset 0x000 ................................ 1245 Analog Comparator Raw Interrupt Status (ACRIS), offset 0x004 ..................................... 1246 Analog Comparator Interrupt Enable (ACINTEN), offset 0x008 ....................................... 1247 November 08, 2011 35 Texas Instruments-Advance Information Table of Contents Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Analog Comparator Reference Voltage Control (ACREFCTL), offset 0x010 ..................... 1248 Analog Comparator Status 0 (ACSTAT0), offset 0x020 ................................................... 1249 Analog Comparator Status 1 (ACSTAT1), offset 0x040 ................................................... 1249 Analog Comparator Status 2 (ACSTAT2), offset 0x060 ................................................... 1249 Analog Comparator Control 0 (ACCTL0), offset 0x024 ................................................... 1250 Analog Comparator Control 1 (ACCTL1), offset 0x044 ................................................... 1250 Analog Comparator Control 2 (ACCTL2), offset 0x064 ................................................... 1250 Analog Comparator Peripheral Properties (ACMPPP), offset 0xFC0 ................................ 1252 Pulse Width Modulator (PWM) .................................................................................................. 1254 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: Register 36: Register 37: Register 38: Register 39: PWM Master Control (PWMCTL), offset 0x000 .............................................................. 1269 PWM Time Base Sync (PWMSYNC), offset 0x004 ......................................................... 1271 PWM Output Enable (PWMENABLE), offset 0x008 ........................................................ 1272 PWM Output Inversion (PWMINVERT), offset 0x00C ..................................................... 1274 PWM Output Fault (PWMFAULT), offset 0x010 .............................................................. 1276 PWM Interrupt Enable (PWMINTEN), offset 0x014 ......................................................... 1278 PWM Raw Interrupt Status (PWMRIS), offset 0x018 ...................................................... 1280 PWM Interrupt Status and Clear (PWMISC), offset 0x01C .............................................. 1283 PWM Status (PWMSTATUS), offset 0x020 .................................................................... 1286 PWM Fault Condition Value (PWMFAULTVAL), offset 0x024 ........................................... 1288 PWM Enable Update (PWMENUPD), offset 0x028 ......................................................... 1290 PWM0 Control (PWM0CTL), offset 0x040 ...................................................................... 1294 PWM1 Control (PWM1CTL), offset 0x080 ...................................................................... 1294 PWM2 Control (PWM2CTL), offset 0x0C0 ..................................................................... 1294 PWM3 Control (PWM3CTL), offset 0x100 ...................................................................... 1294 PWM0 Interrupt and Trigger Enable (PWM0INTEN), offset 0x044 ................................... 1299 PWM1 Interrupt and Trigger Enable (PWM1INTEN), offset 0x084 ................................... 1299 PWM2 Interrupt and Trigger Enable (PWM2INTEN), offset 0x0C4 ................................... 1299 PWM3 Interrupt and Trigger Enable (PWM3INTEN), offset 0x104 ................................... 1299 PWM0 Raw Interrupt Status (PWM0RIS), offset 0x048 ................................................... 1302 PWM1 Raw Interrupt Status (PWM1RIS), offset 0x088 ................................................... 1302 PWM2 Raw Interrupt Status (PWM2RIS), offset 0x0C8 .................................................. 1302 PWM3 Raw Interrupt Status (PWM3RIS), offset 0x108 ................................................... 1302 PWM0 Interrupt Status and Clear (PWM0ISC), offset 0x04C .......................................... 1304 PWM1 Interrupt Status and Clear (PWM1ISC), offset 0x08C .......................................... 1304 PWM2 Interrupt Status and Clear (PWM2ISC), offset 0x0CC .......................................... 1304 PWM3 Interrupt Status and Clear (PWM3ISC), offset 0x10C .......................................... 1304 PWM0 Load (PWM0LOAD), offset 0x050 ...................................................................... 1306 PWM1 Load (PWM1LOAD), offset 0x090 ...................................................................... 1306 PWM2 Load (PWM2LOAD), offset 0x0D0 ...................................................................... 1306 PWM3 Load (PWM3LOAD), offset 0x110 ...................................................................... 1306 PWM0 Counter (PWM0COUNT), offset 0x054 ............................................................... 1307 PWM1 Counter (PWM1COUNT), offset 0x094 ............................................................... 1307 PWM2 Counter (PWM2COUNT), offset 0x0D4 .............................................................. 1307 PWM3 Counter (PWM3COUNT), offset 0x114 ............................................................... 1307 PWM0 Compare A (PWM0CMPA), offset 0x058 ............................................................ 1308 PWM1 Compare A (PWM1CMPA), offset 0x098 ............................................................ 1308 PWM2 Compare A (PWM2CMPA), offset 0x0D8 ............................................................ 1308 PWM3 Compare A (PWM3CMPA), offset 0x118 ............................................................. 1308 36 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 40: Register 41: Register 42: Register 43: Register 44: Register 45: Register 46: Register 47: Register 48: Register 49: Register 50: Register 51: Register 52: Register 53: Register 54: Register 55: Register 56: Register 57: Register 58: Register 59: Register 60: Register 61: Register 62: Register 63: Register 64: Register 65: Register 66: Register 67: Register 68: Register 69: Register 70: Register 71: Register 72: Register 73: Register 74: Register 75: Register 76: Register 77: Register 78: Register 79: Register 80: Register 81: Register 82: Register 83: Register 84: Register 85: Register 86: Register 87: PWM0 Compare B (PWM0CMPB), offset 0x05C ............................................................ 1309 PWM1 Compare B (PWM1CMPB), offset 0x09C ............................................................ 1309 PWM2 Compare B (PWM2CMPB), offset 0x0DC ........................................................... 1309 PWM3 Compare B (PWM3CMPB), offset 0x11C ............................................................ 1309 PWM0 Generator A Control (PWM0GENA), offset 0x060 ............................................... 1310 PWM1 Generator A Control (PWM1GENA), offset 0x0A0 ............................................... 1310 PWM2 Generator A Control (PWM2GENA), offset 0x0E0 ............................................... 1310 PWM3 Generator A Control (PWM3GENA), offset 0x120 ............................................... 1310 PWM0 Generator B Control (PWM0GENB), offset 0x064 ............................................... 1313 PWM1 Generator B Control (PWM1GENB), offset 0x0A4 ............................................... 1313 PWM2 Generator B Control (PWM2GENB), offset 0x0E4 ............................................... 1313 PWM3 Generator B Control (PWM3GENB), offset 0x124 ............................................... 1313 PWM0 Dead-Band Control (PWM0DBCTL), offset 0x068 ............................................... 1316 PWM1 Dead-Band Control (PWM1DBCTL), offset 0x0A8 ............................................... 1316 PWM2 Dead-Band Control (PWM2DBCTL), offset 0x0E8 ............................................... 1316 PWM3 Dead-Band Control (PWM3DBCTL), offset 0x128 ............................................... 1316 PWM0 Dead-Band Rising-Edge Delay (PWM0DBRISE), offset 0x06C ............................ 1317 PWM1 Dead-Band Rising-Edge Delay (PWM1DBRISE), offset 0x0AC ............................ 1317 PWM2 Dead-Band Rising-Edge Delay (PWM2DBRISE), offset 0x0EC ............................ 1317 PWM3 Dead-Band Rising-Edge Delay (PWM3DBRISE), offset 0x12C ............................ 1317 PWM0 Dead-Band Falling-Edge-Delay (PWM0DBFALL), offset 0x070 ............................ 1318 PWM1 Dead-Band Falling-Edge-Delay (PWM1DBFALL), offset 0x0B0 ............................ 1318 PWM2 Dead-Band Falling-Edge-Delay (PWM2DBFALL), offset 0x0F0 ............................ 1318 PWM3 Dead-Band Falling-Edge-Delay (PWM3DBFALL), offset 0x130 ............................ 1318 PWM0 Fault Source 0 (PWM0FLTSRC0), offset 0x074 .................................................. 1319 PWM1 Fault Source 0 (PWM1FLTSRC0), offset 0x0B4 .................................................. 1319 PWM2 Fault Source 0 (PWM2FLTSRC0), offset 0x0F4 .................................................. 1319 PWM3 Fault Source 0 (PWM3FLTSRC0), offset 0x134 .................................................. 1319 PWM0 Fault Source 1 (PWM0FLTSRC1), offset 0x078 .................................................. 1321 PWM1 Fault Source 1 (PWM1FLTSRC1), offset 0x0B8 .................................................. 1321 PWM2 Fault Source 1 (PWM2FLTSRC1), offset 0x0F8 .................................................. 1321 PWM3 Fault Source 1 (PWM3FLTSRC1), offset 0x138 .................................................. 1321 PWM0 Minimum Fault Period (PWM0MINFLTPER), offset 0x07C ................................... 1324 PWM1 Minimum Fault Period (PWM1MINFLTPER), offset 0x0BC ................................... 1324 PWM2 Minimum Fault Period (PWM2MINFLTPER), offset 0x0FC ................................... 1324 PWM3 Minimum Fault Period (PWM3MINFLTPER), offset 0x13C ................................... 1324 PWM0 Fault Pin Logic Sense (PWM0FLTSEN), offset 0x800 .......................................... 1325 PWM1 Fault Pin Logic Sense (PWM1FLTSEN), offset 0x880 .......................................... 1325 PWM2 Fault Pin Logic Sense (PWM2FLTSEN), offset 0x900 .......................................... 1325 PWM3 Fault Pin Logic Sense (PWM3FLTSEN), offset 0x980 .......................................... 1325 PWM0 Fault Status 0 (PWM0FLTSTAT0), offset 0x804 ................................................... 1326 PWM1 Fault Status 0 (PWM1FLTSTAT0), offset 0x884 ................................................... 1326 PWM2 Fault Status 0 (PWM2FLTSTAT0), offset 0x904 ................................................... 1326 PWM3 Fault Status 0 (PWM3FLTSTAT0), offset 0x984 ................................................... 1326 PWM0 Fault Status 1 (PWM0FLTSTAT1), offset 0x808 ................................................... 1328 PWM1 Fault Status 1 (PWM1FLTSTAT1), offset 0x888 ................................................... 1328 PWM2 Fault Status 1 (PWM2FLTSTAT1), offset 0x908 ................................................... 1328 PWM3 Fault Status 1 (PWM3FLTSTAT1), offset 0x988 ................................................... 1328 November 08, 2011 37 Texas Instruments-Advance Information Table of Contents Register 88: Register 89: PWM Peripheral Properties (PWMPP), offset 0xFC0 ...................................................... 1331 PWM Peripheral Configuration (PWMPC), offset 0xFC4 ................................................. 1333 Quadrature Encoder Interface (QEI) ........................................................................................ 1334 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: QEI Control (QEICTL), offset 0x000 .............................................................................. QEI Status (QEISTAT), offset 0x004 .............................................................................. QEI Position (QEIPOS), offset 0x008 ............................................................................ QEI Maximum Position (QEIMAXPOS), offset 0x00C ..................................................... QEI Timer Load (QEILOAD), offset 0x010 ..................................................................... QEI Timer (QEITIME), offset 0x014 ............................................................................... QEI Velocity Counter (QEICOUNT), offset 0x018 ........................................................... QEI Velocity (QEISPEED), offset 0x01C ........................................................................ QEI Interrupt Enable (QEIINTEN), offset 0x020 ............................................................. QEI Raw Interrupt Status (QEIRIS), offset 0x024 ........................................................... QEI Interrupt Status and Clear (QEIISC), offset 0x028 ................................................... 38 1340 1343 1344 1345 1346 1347 1348 1349 1350 1352 1354 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Revision History The revision history table notes changes made between the indicated revisions of the LM4F232H5BB data sheet. Table 1. Revision History Date Revision November 2011 11003 Description ■ Re-organized Architectural Overview chapter. ■ In the System Control chapter: – Corrected reset value for Run Mode Clock Gating Control Register 0 (RCGC0) register. – Corrected reset for the System Properties (SYSPROP) register. – Removed TPSW bit from Non-Volatile Memory Information (NVMSTAT) register as the ROM Software Map (ROMSWMAP) register contains this information. ■ Changed bit names in System Exception Raw Interrupt Status (SYSEXCRIS), System Exception Interrupt Mask (SYSEXCIM), System Exception Masked Interrupt Status (SYSEXCMIS), and System Exception Interrupt Clear (SYSEXCIC) registers to indicate they are for floating-point exceptions. ■ In Hibernation chapter, added section "Arbitrary Power Removal" and corrected figure "Using a Dedicated Oscillator as the Hibernation Clock Source with VDD3ON Mode ". ■ In the Internal Memory chapter, clarified programming and use of the non-volatile registers, including corrections to the Boot Configuration (BOOTCFG) and User Register n (USER_REGn) registers. ■ In the GPIO chapter, corrected table "GPIO Pins With Non-Zero Reset Values". ■ In the General-Purpose Timers chapter, added clarifications on timer operation. ■ In the UART chapter, clarified interrupt behavior. ■ In the I2C chapter: – Added content for Fast-Mode Plus (1 Mbps) mode and High-Speed mode (3.33 Mbps), correcting the reset value of the Device Capabilities 2 (DC2), I2C Master Control/Status (I2CMCS), and I2C Peripheral Properties (I2CPP) registers. – Corrected reset for the I2C Master Control/Status (I2CMCS) register. – Added the HSTPR bit to the I2C Master Timer Period (I2CMTPR) register. – Added the I2C Peripheral Configuration (I2CPC) register. ■ In the USB chapter: – ■ September 2011 10502 Corrected description for the USB Device RESUME Interrupt Mask (USBDRIM) register. In the Analog Comparators chapter: – Corrected table "Internal Reference Voltage and ACREFCTL Field Values". – Corrected bit fields in the Analog Comparator Peripheral Properties (ACMPPP) register. ■ In the Electrical Characteristics chapter: – Clarified load capacitance equations. – Corrected values in table "Analog Comparator Voltage Reference Characteristics". ■ Additional minor data sheet clarifications and corrections. Started tracking revision history. November 08, 2011 39 Texas Instruments-Advance Information About This Document About This Document This data sheet provides reference information for the LM4F232H5BB microcontroller, describing the functional blocks of the system-on-chip (SoC) device designed around the ARM® Cortex™-M4F core. Audience This manual is intended for system software developers, hardware designers, and application developers. About This Manual This document is organized into sections that correspond to each major feature. Related Documents ® The following related documents are available on the Stellaris web site at www.ti.com/stellaris: ■ Stellaris® Errata ■ ARM® Cortex™-M3 Errata ■ Cortex™-M3/M4 Instruction Set Technical User's Manual ■ Stellaris® Boot Loader User's Guide ■ Stellaris® Graphics Library User's Guide ■ Stellaris® Peripheral Driver Library User's Guide ■ Stellaris® ROM User’s Guide ■ Stellaris® USB Library User's Guide The following related documents are also referenced: ■ ARM® Debug Interface V5 Architecture Specification ■ ARM® Embedded Trace Macrocell Architecture Specification ■ IEEE Standard 1149.1-Test Access Port and Boundary-Scan Architecture This documentation list was current as of publication date. Please check the web site for additional documentation, including application notes and white papers. 40 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Documentation Conventions This document uses the conventions shown in Table 2 on page 41. Table 2. Documentation Conventions Notation Meaning General Register Notation REGISTER APB registers are indicated in uppercase bold. For example, PBORCTL is the Power-On and Brown-Out Reset Control register. If a register name contains a lowercase n, it represents more than one register. For example, SRCRn represents any (or all) of the three Software Reset Control registers: SRCR0, SRCR1 , and SRCR2. bit A single bit in a register. bit field Two or more consecutive and related bits. offset 0xnnn A hexadecimal increment to a register's address, relative to that module's base address as specified in Table 2-4 on page 92. Register N Registers are numbered consecutively throughout the document to aid in referencing them. The register number has no meaning to software. reserved Register bits marked reserved are reserved for future use. In most cases, reserved bits are set to 0; however, user software should not rely on the value of a reserved bit. To provide software compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. yy:xx The range of register bits inclusive from xx to yy. For example, 31:15 means bits 15 through 31 in that register. Register Bit/Field Types This value in the register bit diagram indicates whether software running on the controller can change the value of the bit field. RC Software can read this field. The bit or field is cleared by hardware after reading the bit/field. RO Software can read this field. Always write the chip reset value. R/W Software can read or write this field. R/WC Software can read or write this field. Writing to it with any value clears the register. R/W1C Software can read or write this field. A write of a 0 to a W1C bit does not affect the bit value in the register. A write of a 1 clears the value of the bit in the register; the remaining bits remain unchanged. This register type is primarily used for clearing interrupt status bits where the read operation provides the interrupt status and the write of the read value clears only the interrupts being reported at the time the register was read. R/W1S Software can read or write a 1 to this field. A write of a 0 to a R/W1S bit does not affect the bit value in the register. W1C Software can write this field. A write of a 0 to a W1C bit does not affect the bit value in the register. A write of a 1 clears the value of the bit in the register; the remaining bits remain unchanged. A read of the register returns no meaningful data. This register is typically used to clear the corresponding bit in an interrupt register. WO Only a write by software is valid; a read of the register returns no meaningful data. Register Bit/Field Reset Value This value in the register bit diagram shows the bit/field value after any reset, unless noted. 0 Bit cleared to 0 on chip reset. 1 Bit set to 1 on chip reset. - Nondeterministic. Pin/Signal Notation [] Pin alternate function; a pin defaults to the signal without the brackets. pin Refers to the physical connection on the package. signal Refers to the electrical signal encoding of a pin. November 08, 2011 41 Texas Instruments-Advance Information About This Document Table 2. Documentation Conventions (continued) Notation Meaning assert a signal Change the value of the signal from the logically False state to the logically True state. For active High signals, the asserted signal value is 1 (High); for active Low signals, the asserted signal value is 0 (Low). The active polarity (High or Low) is defined by the signal name (see SIGNAL and SIGNAL below). deassert a signal Change the value of the signal from the logically True state to the logically False state. SIGNAL Signal names are in uppercase and in the Courier font. An overbar on a signal name indicates that it is active Low. To assert SIGNAL is to drive it Low; to deassert SIGNAL is to drive it High. SIGNAL Signal names are in uppercase and in the Courier font. An active High signal has no overbar. To assert SIGNAL is to drive it High; to deassert SIGNAL is to drive it Low. Numbers X An uppercase X indicates any of several values is allowed, where X can be any legal pattern. For example, a binary value of 0X00 can be either 0100 or 0000, a hex value of 0xX is 0x0 or 0x1, and so on. 0x Hexadecimal numbers have a prefix of 0x. For example, 0x00FF is the hexadecimal number FF. All other numbers within register tables are assumed to be binary. Within conceptual information, binary numbers are indicated with a b suffix, for example, 1011b, and decimal numbers are written without a prefix or suffix. 42 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 1 Architectural Overview ® Texas Instruments is the industry leader in bringing 32-bit capabilities and the full benefits of ARM Cortex™-M-based microcontrollers to the broadest reach of the microcontroller market. For current ® users of 8- and 16-bit MCUs, Stellaris with Cortex-M offers a direct path to the strongest ecosystem of development tools, software and knowledge in the industry. Designers who migrate to Stellaris benefit from great tools, small code footprint and outstanding performance. Even more important, designers can enter the ARM ecosystem with full confidence in a compatible roadmap from $1 to 1 GHz. With blazingly-fast responsiveness, Thumb-2 technology combines both 16-bit and 32-bit instructions to deliver the best balance of code density and performance. Thumb-2 uses 26 percent less memory than pure 32-bit code to reduce system cost while delivering 25 percent better performance. The Texas Instruments Stellaris family of microcontrollers brings high-performance 32-bit computing to cost-sensitive embedded microcontroller applications. 1.1 Stellaris LM4F Series Overview The Stellaris LM4F series of ARM Cortex-M4 microcontrollers provides top performance and advanced integration. The product family is positioned for cost-conscious applications requiring significant control processing and connectivity capabilities such as: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Low power, hand-held smart devices Gaming equipment Home and commercial site monitoring and control Motion control Medical instrumentation Test and measurement equipment Factory automation Fire and security Smart Energy/Smart Grid solutions Intelligent lighting control Transportation November 08, 2011 43 Texas Instruments-Advance Information Architectural Overview Figure 1-1. Stellaris LM4F Block Diagram The Stellaris LM4F microcontrollers consist of twelve pin-compatible series of devices, summarized below. Each series has a range of embedded flash and SRAM sizes. Table 1-1. Stellaris LM4F Device Series General MCU (LM4F110 Series) General MCU + USB Device General MCU + USB OTG Motion Control + USB Package OTG (LM4F120 Series) (LM4F130 Series) (LM4F230 Series) LM4F110 LM4F120 LM4F130 LM4F230 64-pin LQFP LM4F111 LM4F121 LM4F131 LM4F231 64-pin LQFP LM4F112 LM4F122 LM4F132 LM4F232 100-pin LQFP 144-pin LQFP The Stellaris LM4F230 Series for MCU control applications with advanced motion control timers and USB OTG/ Host/Device offers advanced motion control timers and USB OTG/Host/Device capability with a generous number of serial peripherals in three packages. Table 1-2. Stellaris LM4F230 Series Part Number Flash (KB) SRAM (KB) LM4F230E5QR 128 32 LM4F230H5QR 256 32 5-V Tolerant GPIOs 43 Package Notes 64-pin LQFP Includes low-power hibernate functionality. 44 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 1-2. Stellaris LM4F230 Series (continued) Part Number Flash (KB) SRAM (KB) LM4F231E5QR 128 32 LM4F231H5QR 256 32 LM4F232E5QC 128 32 LM4F232H5QC 256 32 LM4F232H5QD 256 32 5-V Tolerant GPIOs Package Notes 49 64-pin LQFP No low-power hibernate functionality, but includes additional motion control and serial functionality, and up to six more I/Os than the LM4F230 Series. 69 100-pin LQFP 105 144-pin LQFP Includes low-power hibernate functionality, additional motion control, serial, and analog functionality, and up to 20 more I/Os (56 for the 144LQFP) than the LM4F231 Series. Battery-Backed Hibernation PWM PWM Faults QEI Channels CAN MAC USB UART UART Modem Signalling I2C SSI/SPI ADC Channels ADC External Reference Analog/Digital Comparators 5-V Tolerant b GPIOs 32 12 ✔ – – – 1 – 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F110C4QR 64 24 ✔ – – – 1 – 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F110E5QR 128 32 ✔ – – – 1 – 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F110H5QR 256 32 ✔ – – – 1 – 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F111B2QR 32 12 – – – – 1 – 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F111C4QR 64 24 – – – – 1 – 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F111E5QR 128 32 – – – – 1 – 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F111H5QR 256 32 – – – – 1 – 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F112C4QC 64 24 ✔ – – – 1 – 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F112E5QC 128 32 ✔ – – – 1 – 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F112H5QC 256 32 ✔ – – – 1 – 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F112H5QD 256 32 ✔ – – – 1 – 8 ✔ 6 4 24 ✔ 3/16 0-105 144LQFP LM4F120B2QR 32 12 ✔ – – – 1 D 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F120C4QR 64 24 ✔ – – – 1 D 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F120E5QR 128 32 ✔ – – – 1 D 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F120H5QR 256 32 ✔ – – – 1 D 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F121B2QR 32 12 – – – – 1 D 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F121C4QR 64 24 – – – – 1 D 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F121E5QR 128 32 – – – – 1 D 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F121H5QR 256 32 – – – – 1 D 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F122C4QC 64 24 ✔ – – – 1 D 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F122E5QC 128 32 ✔ – – – 1 D 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F122H5QC 256 32 ✔ – – – 1 D 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP Package SRAM (KB) LM4F110B2QR a Part Number Flash (KB) Table 1-3. Stellaris LM4F Family of Devices LM4F122H5QD 256 32 ✔ – – – 1 D 8 ✔ 6 4 24 ✔ 3/16 0-105 144LQFP LM4F130C4QR 64 24 ✔ – – – 1 O 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F130E5QR 128 32 ✔ – – – 1 O 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F130H5QR 256 32 ✔ – – – 1 O 8 – 4 4 12 – 2/16 0-43 64LQFP November 08, 2011 45 Texas Instruments-Advance Information Architectural Overview Battery-Backed Hibernation PWM PWM Faults QEI Channels CAN MAC USB UART UART Modem Signalling I2C SSI/SPI ADC Channels ADC External Reference Analog/Digital Comparators 5-V Tolerant b GPIOs 64 24 – – – – 1 O 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F131E5QR 128 32 – – – – 1 O 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F131H5QR 256 32 – – – – 1 O 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F132C4QC 64 24 ✔ – – – 1 O 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F132E5QC 128 32 ✔ – – – 1 O 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F132H5QC 256 32 ✔ – – – 1 O 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F132H5QD 256 32 ✔ – – – 1 O 8 ✔ 6 4 24 ✔ 3/16 0-105 144LQFP LM4F230E5QR 128 32 ✔ 16 2 2 2 O 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F230H5QR 256 32 ✔ 16 2 2 2 O 8 – 4 4 12 – 2/16 0-43 64LQFP LM4F231E5QR 128 32 – 16 6 2 2 O 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F231H5QR 256 32 – 16 6 2 2 O 8 – 6 4 12 – 2/16 0-49 64LQFP LM4F232E5QC 128 32 ✔ 16 8 2 2 O 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F232H5QC 256 32 ✔ 16 8 2 2 O 8 ✔ 6 4 22 ✔ 3/16 0-69 100LQFP LM4F232H5QD 256 32 ✔ 16 8 2 2 O 8 ✔ 6 4 24 ✔ 3/16 0-105 144LQFP Package SRAM (KB) LM4F131C4QR Part Number a Flash (KB) Table 1-3. Stellaris LM4F Family of Devices (continued) a. USB options for Stellaris microcontrollers include Device Only (D) capability, Host/Device (H) capability, and On-The-Go/Host/Device capability (O). b. Minimum is number of pins dedicated to GPIO; additional pins are available if certain peripherals are not used. See data sheet for details. 1.2 LM4F232H5BB Microcontroller Overview The Stellaris LM4F232H5BB microcontroller combines complex integration and high performance with the following feature highlights: ■ ARM Cortex-M4F Processor Core ■ High Performance: 80-MHz operation; 100 DMIPS performance ■ 256 KB single-cycle Flash memory ■ 32 KB single-cycle SRAM ® ■ Internal ROM loaded with StellarisWare software ■ Advanced Communication Interfaces: UART, SSI, I2C, CAN, USB ■ System Integration: general-purpose timers, watchdog timers, DMA, general-purpose I/Os ■ Advanced motion control using PWMs, fault inputs, and quadrature encoder inputs ■ Analog support: analog and digital comparators, Analog-to-Digital Converters (ADC), on-chip voltage regulator ■ JTAG and ARM Serial Wire Debug (SWD) ■ 157-ball BGA package 46 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Industrial (-40°C to 85°C) temperature range Figure 1-2 on page 48 depicts the features on the Stellaris LM4F232H5BB microcontroller. Note that there are two on-chip buses that connect the core to the peripherals. The Advanced Peripheral Bus (APB) bus is the legacy bus. The Advanced High-Performance Bus (AHB) bus provides better back-to-back access performance than the APB bus. November 08, 2011 47 Texas Instruments-Advance Information Architectural Overview Figure 1-2. Stellaris LM4F232H5BB Microcontroller High-Level Block Diagram JTAG/SWD ARM® Cortex™-M4F ROM (80MHz) System Control and Clocks (w/ Precis. Osc.) FPU NVIC DCode bus Boot Loader DriverLib AES & CRC Flash (256KB) MPU ICode bus System Bus LM4F232H5BB Bus Matrix SRAM (32KB) SYSTEM PERIPHERALS EEPROM (2K) Hibernation Module GPIOs (120) GeneralPurpose Timer (12) USB OTG (FS PHY) SSI (4) Advanced Peripheral Bus (APB) Watchdog Timer (2) Advanced High-Performance Bus (AHB) DMA SERIAL PERIPHERALS UART (8) I2C (6) CAN Controller (2) ANALOG PERIPHERALS Analog Comparator (3) 12- Bit ADC Channels (24) MOTION CONTROL PERIPHERALS PWM (16) QEI (2) 48 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller For applications requiring extreme conservation of power, the LM4F232H5BB microcontroller features a battery-backed Hibernation module to efficiently power down the LM4F232H5BB to a low-power state during extended periods of inactivity. With a power-up/power-down sequencer, a continuous time counter (RTC), a pair of match registers, an APB interface to the system bus, and dedicated battery-backed memory, the Hibernation module positions the LM4F232H5BB microcontroller perfectly for battery applications. In addition, the LM4F232H5BB microcontroller offers the advantages of ARM's widely available development tools, System-on-Chip (SoC) infrastructure IP applications, and a large user community. Additionally, the microcontroller uses ARM's Thumb®-compatible Thumb-2 instruction set to reduce memory requirements and, thereby, cost. Finally, the LM4F232H5BB microcontroller is code-compatible to all members of the extensive Stellaris family; providing flexibility to fit precise needs. Texas Instruments offers a complete solution to get to market quickly, with evaluation and development boards, white papers and application notes, an easy-to-use peripheral driver library, and a strong support, sales, and distributor network. 1.3 LM4F232H5BB Microcontroller Features The LM4F232H5BB microcontroller component features and general function are discussed in more detail in the following section. 1.3.1 ARM Cortex-M4F Processor Core All members of the Stellaris product family, including the LM4F232H5BB microcontroller, are designed around an ARM Cortex-M4F processor core. The ARM Cortex-M4F processor provides the core for a high-performance, low-cost platform that meets the needs of minimal memory implementation, reduced pin count, and low power consumption, while delivering outstanding computational performance and exceptional system response to interrupts. 1.3.1.1 Processor Core (see page 69) ■ 32-bit ARM Cortex-M4F architecture optimized for small-footprint embedded applications ■ 80-MHz operation; 100 DMIPS performance ■ Outstanding processing performance combined with fast interrupt handling ■ Thumb-2 mixed 16-/32-bit instruction set delivers the high performance expected of a 32-bit ARM core in a compact memory size usually associated with 8- and 16-bit devices, typically in the range of a few kilobytes of memory for microcontroller-class applications – Single-cycle multiply instruction and hardware divide – Atomic bit manipulation (bit-banding), delivering maximum memory utilization and streamlined peripheral control – Unaligned data access, enabling data to be efficiently packed into memory ■ IEEE754-compliant single-precision Floating-Point Unit (FPU) ■ 16-bit SIMD vector processing unit ■ Fast code execution permits slower processor clock or increases sleep mode time November 08, 2011 49 Texas Instruments-Advance Information Architectural Overview ■ Harvard architecture characterized by separate buses for instruction and data ■ Efficient processor core, system and memories ■ Hardware division and fast digital-signal-processing orientated multiply accumulate ■ Saturating arithmetic for signal processing ■ Deterministic, high-performance interrupt handling for time-critical applications ■ Memory protection unit (MPU) to provide a privileged mode for protected operating system functionality ■ Enhanced system debug with extensive breakpoint and trace capabilities ■ Serial Wire Debug and Serial Wire Trace reduce the number of pins required for debugging and tracing ■ Migration from the ARM7 processor family for better performance and power efficiency ■ Optimized for single-cycle Flash memory usage ■ Ultra-low power consumption with integrated sleep modes 1.3.1.2 System Timer (SysTick) (see page 125) ARM Cortex-M4F includes an integrated system timer, SysTick. SysTick provides a simple, 24-bit, clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter can be used in several different ways, for example: ■ An RTOS tick timer that fires at a programmable rate (for example, 100 Hz) and invokes a SysTick routine ■ A high-speed alarm timer using the system clock ■ A variable rate alarm or signal timer—the duration is range-dependent on the reference clock used and the dynamic range of the counter ■ A simple counter used to measure time to completion and time used ■ An internal clock-source control based on missing/meeting durations. 1.3.1.3 Nested Vectored Interrupt Controller (NVIC) (see page 126) The LM4F232H5BB controller includes the ARM Nested Vectored Interrupt Controller (NVIC). The NVIC and Cortex-M4F prioritize and handle all exceptions in Handler Mode. The processor state is automatically stored to the stack on an exception and automatically restored from the stack at the end of the Interrupt Service Routine (ISR). The interrupt vector is fetched in parallel to the state saving, enabling efficient interrupt entry. The processor supports tail-chaining, meaning that back-to-back interrupts can be performed without the overhead of state saving and restoration. Software can set eight priority levels on 7 exceptions (system handlers) and 104 interrupts. ■ Deterministic, fast interrupt processing: always 12 cycles, or just 6 cycles with tail-chaining ■ External non-maskable interrupt signal (NMI) available for immediate execution of NMI handler for safety critical applications 50 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Dynamically reprioritizable interrupts ■ Exceptional interrupt handling via hardware implementation of required register manipulations 1.3.1.4 System Control Block (SCB) (see page 127) The SCB provides system implementation information and system control, including configuration, control, and reporting of system exceptions. 1.3.1.5 Memory Protection Unit (MPU) (see page 127) The MPU supports the standard ARM7 Protected Memory System Architecture (PMSA) model. The MPU provides full support for protection regions, overlapping protection regions, access permissions, and exporting memory attributes to the system. 1.3.1.6 Floating-Point Unit (FPU) (see page 132) The FPU fully supports single-precision add, subtract, multiply, divide, multiply and accumulate, and square root operations. It also provides conversions between fixed-point and floating-point data formats, and floating-point constant instructions. ■ 32-bit instructions for single-precision (C float) data-processing operations ■ Combined Multiply and Accumulate instructions for increased precision (Fused MAC) ■ Hardware support for conversion, addition, subtraction, multiplication with optional accumulate, division, and square-root ■ Hardware support for denormals and all IEEE rounding modes ■ 32 dedicated 32-bit single-precision registers, also addressable as 16 double-word registers ■ Decoupled three stage pipeline 1.3.2 On-Chip Memory The LM4F232H5BB microcontroller is integrated with the following set of on-chip memory and features: ■ 256 KB single-cycle Flash memory up to 40 MHz; a prefetch buffer improves performance above 40 MHz ■ 32 KB single-cycle SRAM ■ Internal ROM loaded with StellarisWare software: – Stellaris Peripheral Driver Library – Stellaris Boot Loader – Advanced Encryption Standard (AES) cryptography tables – Cyclic Redundancy Check (CRC) error detection functionality ■ 2KB EEPROM 1.3.2.1 SRAM (see page 553) The LM4F232H5BB microcontroller provides 32 KB of single-cycle on-chip SRAM. The internal SRAM of the Stellaris devices is located at offset 0x2000.0000 of the device memory map. November 08, 2011 51 Texas Instruments-Advance Information Architectural Overview Because read-modify-write (RMW) operations are very time consuming, ARM has introduced bit-banding technology in the Cortex-M4F processor. With a bit-band-enabled processor, certain regions in the memory map (SRAM and peripheral space) can use address aliases to access individual bits in a single, atomic operation. Data can be transferred to and from the SRAM using the Micro Direct Memory Access Controller (µDMA). 1.3.2.2 Flash Memory (see page 556) The LM4F232H5BB microcontroller provides 256 KB of single-cycle on-chip Flash memory. The Flash memory is organized as a set of 1-KB blocks that can be individually erased. Erasing a block causes the entire contents of the block to be reset to all 1s. These blocks are paired into a set of 2-KB blocks that can be individually protected. The blocks can be marked as read-only or execute-only, providing different levels of code protection. Read-only blocks cannot be erased or programmed, protecting the contents of those blocks from being modified. Execute-only blocks cannot be erased or programmed, and can only be read by the controller instruction fetch mechanism, protecting the contents of those blocks from being read by either the controller or by a debugger. 1.3.2.3 ROM (see page 554) The LM4F232H5BB ROM is preprogrammed with the following software and programs: ■ Stellaris Peripheral Driver Library ■ Stellaris Boot Loader ■ Advanced Encryption Standard (AES) cryptography tables ■ Cyclic Redundancy Check (CRC) error-detection functionality The Stellaris Peripheral Driver Library is a royalty-free software library for controlling on-chip peripherals with a boot-loader capability. The library performs both peripheral initialization and control functions, with a choice of polled or interrupt-driven peripheral support. In addition, the library is designed to take full advantage of the stellar interrupt performance of the ARM Cortex-M4F core. No special pragmas or custom assembly code prologue/epilogue functions are required. For applications that require in-field programmability, the royalty-free Stellaris Boot Loader can act as an application loader and support in-field firmware updates. The Advanced Encryption Standard (AES) is a publicly defined encryption standard used by the U.S. Government. AES is a strong encryption method with reasonable performance and size. In addition, it is fast in both hardware and software, is fairly easy to implement, and requires little memory. The Texas Instruments encryption package is available with full source code, and is based on lesser general public license (LGPL) source. An LGPL means that the code can be used within an application without any copyleft implications for the application (the code does not automatically become open source). Modifications to the package source, however, must be open source. CRC (Cyclic Redundancy Check) is a technique to validate a span of data has the same contents as when previously checked. This technique can be used to validate correct receipt of messages (nothing lost or modified in transit), to validate data after decompression, to validate that Flash memory contents have not been changed, and for other cases where the data needs to be validated. A CRC is preferred over a simple checksum (e.g. XOR all bits) because it catches changes more readily. 52 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 1.3.2.4 EEPROM (see page 560) The LM4F232H5BB microcontroller includes an EEPROM with the following features: ■ 2K bytes of memory accessible as 512 32-bit words ■ 32 blocks of 16 words (64 bytes) each ■ Built-in wear leveling ■ Access protection per block ■ Lock protection option for the whole peripheral as well as per block using 32-bit to 96-bit unlock codes (application selectable) ■ Interrupt support for write completion to avoid polling ■ Endurance of 500K writes (when writing at fixed offset in every alternate page in circular fashion) to 15M operations (when cycling through two pages ) per each 2-page block. 1.3.3 Serial Communications Peripherals The LM4F232H5BB controller supports both asynchronous and synchronous serial communications with: ■ Two CAN 2.0 A/B controllers ■ USB 2.0 OTG/Host/Device ■ Eight UARTs with IrDA, 9-bit and ISO 7816 support (one UART with modem flow control and status) ■ Six I2C modules with four transmission speeds including high-speed mode ■ Four Synchronous Serial Interface modules (SSI) The following sections provide more detail on each of these communications functions. 1.3.3.1 Controller Area Network (see page 1073) Controller Area Network (CAN) is a multicast shared serial-bus standard for connecting electronic control units (ECUs). CAN was specifically designed to be robust in electromagnetically noisy environments and can utilize a differential balanced line like RS-485 or twisted-pair wire. Originally created for automotive purposes, it is now used in many embedded control applications (for example, industrial or medical). Bit rates up to 1 Mbps are possible at network lengths below 40 meters. Decreased bit rates allow longer network distances (for example, 125 Kbps at 500m). A transmitter sends a message to all CAN nodes (broadcasting). Each node decides on the basis of the identifier received whether it should process the message. The identifier also determines the priority that the message enjoys in competition for bus access. Each CAN message can transmit from 0 to 8 bytes of user information. The LM4F232H5BB microcontroller includes two CAN units with the following features: ■ CAN protocol version 2.0 part A/B ■ Bit rates up to 1 Mbps November 08, 2011 53 Texas Instruments-Advance Information Architectural Overview ■ 32 message objects with individual identifier masks ■ Maskable interrupt ■ Disable Automatic Retransmission mode for Time-Triggered CAN (TTCAN) applications ■ Programmable Loopback mode for self-test operation ■ Programmable FIFO mode enables storage of multiple message objects ■ Gluelessly attaches to an external CAN transceiver through the CANnTX and CANnRX signals 1.3.3.2 USB (see page 1124) Universal Serial Bus (USB) is a serial bus standard designed to allow peripherals to be connected and disconnected using a standardized interface without rebooting the system. The LM4F232H5BB microcontroller supports three configurations in USB 2.0 full and low speed: USB Device, USB Host, and USB On-The-Go (negotiated on-the-go as host or device when connected to other USB-enabled systems). The USB module has the following features: ■ Complies with USB-IF certification standards ■ USB 2.0 full-speed (12 Mbps) and low-speed (1.5 Mbps) operation with integrated PHY ■ 4 transfer types: Control, Interrupt, Bulk, and Isochronous ■ 16 endpoints – 1 dedicated control IN endpoint and 1 dedicated control OUT endpoint – 7 configurable IN endpoints and 7 configurable OUT endpoints ■ 4 KB dedicated endpoint memory: one endpoint may be defined for double-buffered 1023-byte isochronous packet size ■ VBUS droop and valid ID detection and interrupt ■ Efficient transfers using Micro Direct Memory Access Controller (µDMA) – Separate channels for transmit and receive for up to three IN endpoints and three OUT endpoints – Channel requests asserted when FIFO contains required amount of data 1.3.3.3 UART (see page 918) A Universal Asynchronous Receiver/Transmitter (UART) is an integrated circuit used for RS-232C serial communications, containing a transmitter (parallel-to-serial converter) and a receiver (serial-to-parallel converter), each clocked separately. The LM4F232H5BB microcontroller includes eight fully programmable 16C550-type UARTs. Although the functionality is similar to a 16C550 UART, this UART design is not register compatible. The UART can generate individually masked interrupts from the Rx, Tx, modem flow control, modem status, and error conditions. The module generates a single combined interrupt when any of the interrupts are asserted and are unmasked. 54 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller The eight UARTs have the following features: ■ Programmable baud-rate generator allowing speeds up to 5 Mbps for regular speed (divide by 16) and 10 Mbps for high speed (divide by 8) ■ Separate 16x8 transmit (TX) and receive (RX) FIFOs to reduce CPU interrupt service loading ■ Programmable FIFO length, including 1-byte deep operation providing conventional double-buffered interface ■ FIFO trigger levels of 1/8, 1/4, 1/2, 3/4, and 7/8 ■ Standard asynchronous communication bits for start, stop, and parity ■ Line-break generation and detection ■ Fully programmable serial interface characteristics – 5, 6, 7, or 8 data bits – Even, odd, stick, or no-parity bit generation/detection – 1 or 2 stop bit generation ■ IrDA serial-IR (SIR) encoder/decoder providing – Programmable use of IrDA Serial Infrared (SIR) or UART input/output – Support of IrDA SIR encoder/decoder functions for data rates up to 115.2 Kbps half-duplex – Support of normal 3/16 and low-power (1.41-2.23 μs) bit durations – Programmable internal clock generator enabling division of reference clock by 1 to 256 for low-power mode bit duration ■ Support for communication with ISO 7816 smart cards ■ Modem flow control and status (on UART1) ■ LIN protocol support ■ EIA-485 9-bit support ■ Standard FIFO-level and End-of-Transmission interrupts ■ Efficient transfers using Micro Direct Memory Access Controller (µDMA) – Separate channels for transmit and receive – Receive single request asserted when data is in the FIFO; burst request asserted at programmed FIFO level – Transmit single request asserted when there is space in the FIFO; burst request asserted at programmed FIFO level November 08, 2011 55 Texas Instruments-Advance Information Architectural Overview 1.3.3.4 I2C (see page 1028) The Inter-Integrated Circuit (I2C) bus provides bi-directional data transfer through a two-wire design (a serial data line SDA and a serial clock line SCL). The I2C bus interfaces to external I2C devices such as serial memory (RAMs and ROMs), networking devices, LCDs, tone generators, and so on. The I2C bus may also be used for system testing and diagnostic purposes in product development and manufacture. Each device on the I2C bus can be designated as either a master or a slave. I2C module supports both sending and receiving data as either a master or a slave and can operate simultaneously as both a master and a slave. Both the I2C master and slave can generate interrupts. The LM4F232H5BB microcontroller includes six I2C modules with the following features: ■ Devices on the I2C bus can be designated as either a master or a slave – Supports both transmitting and receiving data as either a master or a slave – Supports simultaneous master and slave operation ■ Four I2C modes – Master transmit – Master receive – Slave transmit – Slave receive ■ Four transmission speeds: – Standard (100 Kbps) – Fast-mode (400 Kbps) – Fast-mode plus (1 Mbps) – High-speed mode (3.33 Mbps) ■ Clock low timeout interrupt ■ Dual slave address capability ■ Clock low timeout interrupt ■ Dual slave address capability ■ Master and slave interrupt generation – Master generates interrupts when a transmit or receive operation completes (or aborts due to an error) – Slave generates interrupts when data has been transferred or requested by a master or when a START or STOP condition is detected 56 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Master with arbitration and clock synchronization, multimaster support, and 7-bit addressing mode 1.3.3.5 SSI (see page 985) Synchronous Serial Interface (SSI) is a four-wire bi-directional communications interface that converts data between parallel and serial. The SSI module performs serial-to-parallel conversion on data received from a peripheral device, and parallel-to-serial conversion on data transmitted to a peripheral device. The SSI module can be configured as either a master or slave device. As a slave device, the SSI module can also be configured to disable its output, which allows a master device to be coupled with multiple slave devices. The TX and RX paths are buffered with separate internal FIFOs. The SSI module also includes a programmable bit rate clock divider and prescaler to generate the output serial clock derived from the SSI module's input clock. Bit rates are generated based on the input clock and the maximum bit rate is determined by the connected peripheral. The LM4F232H5BB microcontroller includes four SSI modules with the following features: ■ Programmable interface operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces ■ Master or slave operation ■ Programmable clock bit rate and prescaler ■ Separate transmit and receive FIFOs, each 16 bits wide and 8 locations deep ■ Programmable data frame size from 4 to 16 bits ■ Internal loopback test mode for diagnostic/debug testing ■ Standard FIFO-based interrupts and End-of-Transmission interrupt ■ Efficient transfers using Micro Direct Memory Access Controller (µDMA) – Separate channels for transmit and receive – Receive single request asserted when data is in the FIFO; burst request asserted when FIFO contains 4 entries – Transmit single request asserted when there is space in the FIFO; burst request asserted when FIFO contains 4 entries 1.3.4 System Integration The LM4F232H5BB microcontroller provides a variety of standard system functions integrated into the device, including: ■ Direct Memory Access Controller (DMA) ■ System control and clocks including on-chip precision 16-MHz oscillator ■ Six 32-bit timers (up to twelve 16-bit) ■ Six wide 64-bit timers (up to twelve 32-bit) ■ Twelve 16/32-bit Capture Compare PWM (CCP) pins November 08, 2011 57 Texas Instruments-Advance Information Architectural Overview ■ Twelve 32/64-bit Capture Compare PWM (CCP) pins ■ Lower-power battery-backed Hibernation module ■ Real-Time Clock in Hibernation module ■ Two Watchdog Timers – One timer runs off the main oscillator – One timer runs off the precision internal oscillator ■ Up to 120 GPIOs, depending on configuration – Highly flexible pin muxing allows use as GPIO or one of several peripheral functions – Independently configurable to 2, 4 or 8 mA drive capability – Up to 4 GPIOs can have 18 mA drive capability The following sections provide more detail on each of these functions. 1.3.4.1 Direct Memory Access (see page 610) The LM4F232H5BB microcontroller includes a Direct Memory Access (DMA) controller, known as micro-DMA (μDMA). The μDMA controller provides a way to offload data transfer tasks from the Cortex-M4F processor, allowing for more efficient use of the processor and the available bus bandwidth. The μDMA controller can perform transfers between memory and peripherals. It has dedicated channels for each supported on-chip module and can be programmed to automatically perform transfers between peripherals and memory as the peripheral is ready to transfer more data. The μDMA controller provides the following features: ® ■ ARM PrimeCell 32-channel configurable µDMA controller ■ Support for memory-to-memory, memory-to-peripheral, and peripheral-to-memory in multiple transfer modes – Basic for simple transfer scenarios – Ping-pong for continuous data flow – Scatter-gather for a programmable list of arbitrary transfers initiated from a single request ■ Highly flexible and configurable channel operation – Independently configured and operated channels – Dedicated channels for supported on-chip modules – Flexible channel assignments – One channel each for receive and transmit path for bidirectional modules – Dedicated channel for software-initiated transfers – Per-channel configurable priority scheme – Optional software-initiated requests for any channel ■ Two levels of priority 58 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Design optimizations for improved bus access performance between µDMA controller and the processor core – µDMA controller access is subordinate to core access – RAM striping – Peripheral bus segmentation ■ Data sizes of 8, 16, and 32 bits ■ Transfer size is programmable in binary steps from 1 to 1024 ■ Source and destination address increment size of byte, half-word, word, or no increment ■ Maskable peripheral requests ■ Interrupt on transfer completion, with a separate interrupt per channel 1.3.4.2 System Control and Clocks (see page 214) System control determines the overall operation of the device. It provides information about the device, controls power-saving features, controls the clocking of the device and individual peripherals, and handles reset detection and reporting. ■ Device identification information: version, part number, SRAM size, Flash memory size, and so on ■ Power control – On-chip fixed Low Drop-Out (LDO) voltage regulator – Hibernation module handles the power-up/down 3.3 V sequencing and control for the core digital logic and analog circuits – Low-power options for microcontroller: Sleep and Deep-sleep modes with clock gating – Low-power options for on-chip modules: software controls shutdown of individual peripherals and memory – 3.3-V supply brown-out detection and reporting via interrupt or reset ■ Multiple clock sources for microcontroller system clock – Precision Oscillator (PIOSC): On-chip resource providing a 16 MHz ±1% frequency at room temperature • 16 MHz ±3% across temperature • Can be recalibrated with 7-bit trim resolution • Software power down control for low power modes – Main Oscillator (MOSC): A frequency-accurate clock source by one of two means: an external single-ended clock source is connected to the OSC0 input pin, or an external crystal is connected across the OSC0 input and OSC1 output pins. • External crystal used with or without on-chip PLL: select supported frequencies from 4 MHz to 25 MHz. • External oscillator: from DC to maximum device speed November 08, 2011 59 Texas Instruments-Advance Information Architectural Overview – Internal 30-kHz Oscillator: on chip resource providing a 30 kHz ± 50% frequency, used during power-saving modes – 32.768-kHz external oscillator for the Hibernation Module: eliminates need for additional crystal for main clock source ■ Flexible reset sources – Power-on reset (POR) – Reset pin assertion – Brown-out reset (BOR) detector alerts to system power drops – Software reset – Watchdog timer reset – MOSC failure 1.3.4.3 Programmable Timers (see page 734) Programmable timers can be used to count or time external events that drive the Timer input pins. Each 16/32-bit GPTM block provides two 16-bit timers/counters that can be configured to operate independently as timers or event counters, or configured to operate as one 32-bit timer or one 32-bit Real-Time Clock (RTC). Each 32/64-bit Wide GPTM block provides two 32-bit timers/counters that can be configured to operate independently as timersor event counters, or configured to operate as one 64-bit timer or one 64-bit Real-Time Clock (RTC). Timers can also be used to trigger analog-to-digital (ADC) conversions. The General-Purpose Timer Module (GPTM) contains six 16/32-bit GPTM blocks and six 32/64-bit Wide GPTM blocks with the following functional options: ■ 16/32-bit operating modes: – 16- or 32-bit programmable one-shot timer – 16- or 32-bit programmable periodic timer – 16-bit general-purpose timer with an 8-bit prescaler – 32-bit Real-Time Clock (RTC) when using an external 32.768-KHz clock as the input – 16-bit input-edge count- or time-capture modes with an 8-bit prescaler – 16-bit PWM mode with an 8-bit prescaler and software-programmable output inversion of the PWM signal ■ 32/64-bit operating modes: – 32- or 64-bit programmable one-shot timer – 32- or 64-bit programmable periodic timer – 32-bit general-purpose timer with a 16-bit prescaler – 64-bit Real-Time Clock (RTC) when using an external 32.768-KHz clock as the input 60 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller – 32-bit input-edge count- or time-capture modes with a16-bit prescaler – 32-bit PWM mode with a 16-bit prescaler and software-programmable output inversion of the PWM signal ■ Count up or down ■ Twelve 16/32-bit Capture Compare PWM pins (CCP) ■ Twelve 32/64-bit Capture Compare PWM pins (CCP) ■ Daisy chaining of timer modules to allow a single timer to initiate multiple timing events ■ Timer synchronization allows selected timers to start counting on the same clock cycle ■ ADC event trigger ■ User-enabled stalling when the microcontroller asserts CPU Halt flag during debug (excluding RTC mode) ■ Ability to determine the elapsed time between the assertion of the timer interrupt and entry into the interrupt service routine. ■ Efficient transfers using Micro Direct Memory Access Controller (µDMA) – Dedicated channel for each timer – Burst request generated on timer interrupt 1.3.4.4 CCP Pins (see page 743) Capture Compare PWM pins (CCP) can be used by the General-Purpose Timer Module to time/count external events using the CCP pin as an input. Alternatively, the GPTM can generate a simple PWM output on the CCP pin. The LM4F232H5BB microcontroller includes twelve 16/32-bit CCP pins that can be programmed to operate in the following modes: ■ Capture: The GP Timer is incremented/decremented by programmed events on the CCP input. The GP Timer captures and stores the current timer value when a programmed event occurs. ■ Compare: The GP Timer is incremented/decremented by programmed events on the CCP input. The GP Timer compares the current value with a stored value and generates an interrupt when a match occurs. ■ PWM: The GP Timer is incremented/decremented by the system clock. A PWM signal is generated based on a match between the counter value and a value stored in a match register and is output on the CCP pin. 1.3.4.5 Hibernation Module (see page 522) The Hibernation module provides logic to switch power off to the main processor and peripherals and to wake on external or time-based events. The Hibernation module includes power-sequencing logic and has the following features: ■ 32-bit real-time seconds counter (RTC) with 1/32,768 second resolution November 08, 2011 61 Texas Instruments-Advance Information Architectural Overview – 32-bit RTC seconds match register and 15-bit sub seconds match for timed wake-up and interrupt generation with 1/32,768 second resolution – RTC predivider trim for making fine adjustments to the clock rate ■ Two mechanisms for power control – System power control using discrete external regulator – On-chip power control using internal switches under register control ■ Dedicated pin for waking using an external signal ■ RTC operational and hibernation memory valid as long as VBAT is valid ■ Low-battery detection, signaling, and interrupt generation, with optional wake on low battery ■ GPIO pin state can be retained during hibernation ■ Clock source from a 32.768-kHz external crystal or oscillator ■ 16 32-bit words of battery-backed memory to save state during hibernation ■ Programmable interrupts for RTC match, external wake, and low battery events 1.3.4.6 Watchdog Timers (see page 804) A watchdog timer is used to regain control when a system has failed due to a software error or to the failure of an external device to respond in the expected way. The Stellaris Watchdog Timer can generate an interrupt, a non-maskable interrupt, or a reset when a time-out value is reached. In addition, the Watchdog Timer is ARM FiRM-compliant and can be configured to generate an interrupt to the microcontroller on its first time-out, and to generate a reset signal on its second time-out. Once the Watchdog Timer has been configured, the lock register can be written to prevent the timer configuration from being inadvertently altered. The LM4F232H5BB microcontroller has two Watchdog Timer modules: Watchdog Timer 0 uses the system clock for its timer clock; Watchdog Timer 1 uses the PIOSC as its timer clock. The Stellaris Watchdog Timer module has the following features: ■ 32-bit down counter with a programmable load register ■ Separate watchdog clock with an enable ■ Programmable interrupt generation logic with interrupt masking and optional NMI function ■ Lock register protection from runaway software ■ Reset generation logic with an enable/disable ■ User-enabled stalling when the microcontroller asserts the CPU Halt flag during debug 1.3.4.7 Programmable GPIOs (see page 674) General-purpose input/output (GPIO) pins offer flexibility for a variety of connections. The Stellaris GPIO module is comprised of 15 physical GPIO blocks, each corresponding to an individual GPIO port. The GPIO module is FiRM-compliant (compliant to the ARM Foundation IP for Real-Time Microcontrollers specification) and supports 0-120 programmable input/output pins. The number of 62 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller GPIOs available depends on the peripherals being used (see “Signal Tables” on page 1357 for the signals available to each GPIO pin). ■ Up to 120 GPIOs, depending on configuration ■ Highly flexible pin muxing allows use as GPIO or one of several peripheral functions ■ 5-V-tolerant in input configuration ■ Two means of port access: either Advanced High-Performance Bus (AHB) with better back-to-back access performance, or the legacy Advanced Peripheral Bus (APB) for backwards-compatibility with existing code for Ports A-H and J; Ports K-N and P-Q are accessed through the AHB ■ Fast toggle capable of a change every clock cycle for ports on AHB, every two clock cycles for ports on APB ■ Programmable control for GPIO interrupts – Interrupt generation masking – Edge-triggered on rising, falling, or both – Level-sensitive on High or Low values – Per-pin interrupts available on Port P and Port Q ■ Bit masking in both read and write operations through address lines ■ Can be used to initiate an ADC sample sequence or a μDMA transfer ■ Pin state can be retained during Hibernation mode ■ Pins configured as digital inputs are Schmitt-triggered ■ Programmable control for GPIO pad configuration – Weak pull-up or pull-down resistors – 2-mA, 4-mA, and 8-mA pad drive for digital communication; up to four pads can sink 18-mA for high-current applications – Slew rate control for the 8-mA drive – Open drain enables – Digital input enables 1.3.5 Advanced Motion Control The LM4F232H5BB microcontroller provides motion control functions integrated into the device, including: ■ Two PWM modules, with a total of 16 advanced PWM outputs for motion and energy applications ■ Eight fault inputs to promote low-latency shutdown ■ Two Quadrature Encoder Inputs (QEI) November 08, 2011 63 Texas Instruments-Advance Information Architectural Overview The following provides more detail on these motion control functions. 1.3.5.1 PWM (see page 1254) Pulse width modulation (PWM) is a powerful technique for digitally encoding analog signal levels. High-resolution counters are used to generate a square wave, and the duty cycle of the square wave is modulated to encode an analog signal. Typical applications include switching power supplies and motor control. Each LM4F232H5BB PWM module consists of four PWM generator block and a control block. Each PWM generator block contains one timer (16-bit down or up/down counter), two comparators, a PWM signal generator, a dead-band generator, and an interrupt/ADC-trigger selector. Each PWM generator block produces two PWM signals that can either be independent signals or a single pair of complementary signals with dead-band delays inserted. Each PWM generator has the following features: ■ Four fault-condition handling inputs to quickly provide low-latency shutdown and prevent damage to the motor being controlled, for a total of eight inputs ■ One 16-bit counter – Runs in Down or Up/Down mode – Output frequency controlled by a 16-bit load value – Load value updates can be synchronized – Produces output signals at zero and load value ■ Two PWM comparators – Comparator value updates can be synchronized – Produces output signals on match ■ PWM signal generator – Output PWM signal is constructed based on actions taken as a result of the counter and PWM comparator output signals – Produces two independent PWM signals ■ Dead-band generator – Produces two PWM signals with programmable dead-band delays suitable for driving a half-H bridge – Can be bypassed, leaving input PWM signals unmodified ■ Can initiate an ADC sample sequence The control block determines the polarity of the PWM signals and which signals are passed through to the pins. The output of the PWM generation blocks are managed by the output control block before being passed to the device pins. The PWM control block has the following options: ■ PWM output enable of each PWM signal ■ Optional output inversion of each PWM signal (polarity control) 64 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Optional fault handling for each PWM signal ■ Synchronization of timers in the PWM generator blocks ■ Synchronization of timer/comparator updates across the PWM generator blocks ■ Extended PWM synchronization of timer/comparator updates across the PWM generator blocks ■ Interrupt status summary of the PWM generator blocks ■ Extended PWM fault handling, with multiple fault signals, programmable polarities, and filtering ■ PWM generators can be operated independently or synchronized with other generators 1.3.5.2 QEI (see page 1334) A quadrature encoder, also known as a 2-channel incremental encoder, converts linear displacement into a pulse signal. By monitoring both the number of pulses and the relative phase of the two signals, the position, direction of rotation, and speed can be tracked. In addition, a third channel, or index signal, can be used to reset the position counter. The Stellaris quadrature encoder with index (QEI) module interprets the code produced by a quadrature encoder wheel to integrate position over time and determine direction of rotation. In addition, it can capture a running estimate of the velocity of the encoder wheel. The input frequency of the QEI inputs may be as high as 1/4 of the processor frequency (for example, 20 MHz for a 80-MHz system). The LM4F232H5BB microcontroller includes two QEI modules providing control of two motors at the same time with the following features: ■ Position integrator that tracks the encoder position ■ Programmable noise filter on the inputs ■ Velocity capture using built-in timer ■ The input frequency of the QEI inputs may be as high as 1/4 of the processor frequency (for example, 12.5 MHz for a 50-MHz system) ■ Interrupt generation on: – Index pulse – Velocity-timer expiration – Direction change – Quadrature error detection 1.3.6 Analog The LM4F232H5BB microcontroller provides analog functions integrated into the device, including: ■ Two 12-bit Analog-to-Digital Converters (ADC) with 24 analog input channels and a sample rate of one million samples/second ■ Three analog comparators ■ 16 digital comparators November 08, 2011 65 Texas Instruments-Advance Information Architectural Overview ■ On-chip voltage regulator The following provides more detail on these analog functions. 1.3.6.1 ADC (see page 829) An analog-to-digital converter (ADC) is a peripheral that converts a continuous analog voltage to a discrete digital number. The Stellaris ADC module features 12-bit conversion resolution and supports 24 input channels plus an internal temperature sensor. Four buffered sample sequencers allow rapid sampling of up to 24 analog input sources without controller intervention. Each sample sequencer provides flexible programming with fully configurable input source, trigger events, interrupt generation, and sequencer priority. Each ADC module has a digital comparator function that allows the conversion value to be diverted to a comparison unit that provides eight digital comparators. The LM4F232H5BB microcontroller provides two ADC modules with the following features: ■ 24 shared analog input channels ■ 12-bit precision ADC ■ Single-ended and differential-input configurations ■ On-chip internal temperature sensor ■ Maximum sample rate of one million samples/second ■ Optional phase shift in sample time programmable from 22.5º to 337.5º ■ Four programmable sample conversion sequencers from one to eight entries long, with corresponding conversion result FIFOs ■ Flexible trigger control – Controller (software) – Timers – Analog Comparators – PWM – GPIO ■ Hardware averaging of up to 64 samples ■ Digital comparison unit providing eight digital comparators ■ Converter uses a VDDA and GNDA as the voltage reference or two external reference signals ■ Power and ground for the analog circuitry is separate from the digital power and ground ■ Efficient transfers using Micro Direct Memory Access Controller (µDMA) – Dedicated channel for each sample sequencer – ADC module uses burst requests for DMA 66 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 1.3.6.2 Analog Comparators (see page 1239) An analog comparator is a peripheral that compares two analog voltages and provides a logical output that signals the comparison result. The LM4F232H5BB microcontroller provides three independent integrated analog comparators that can be configured to drive an output or generate an interrupt or ADC event. The comparator can provide its output to a device pin, acting as a replacement for an analog comparator on the board, or it can be used to signal the application via interrupts or triggers to the ADC to cause it to start capturing a sample sequence. The interrupt generation and ADC triggering logic is separate. This means, for example, that an interrupt can be generated on a rising edge and the ADC triggered on a falling edge. The LM4F232H5BB microcontroller provides three independent integrated analog comparators with the following functions: ■ Compare external pin input to external pin input or to internal programmable voltage reference ■ Compare a test voltage against any one of the following voltages: – An individual external reference voltage – A shared single external reference voltage – A shared internal reference voltage 1.3.7 JTAG and ARM Serial Wire Debug (see page 202) The Joint Test Action Group (JTAG) port is an IEEE standard that defines a Test Access Port and Boundary Scan Architecture for digital integrated circuits and provides a standardized serial interface for controlling the associated test logic. The TAP, Instruction Register (IR), and Data Registers (DR) can be used to test the interconnections of assembled printed circuit boards and obtain manufacturing information on the components. The JTAG Port also provides a means of accessing and controlling design-for-test features such as I/O pin observation and control, scan testing, and debugging. Texas Instruments replaces the ARM SW-DP and JTAG-DP with the ARM Serial Wire JTAG Debug Port (SWJ-DP) interface. The SWJ-DP interface combines the SWD and JTAG debug ports into one module providing all the normal JTAG debug and test functionality plus real-time access to system memory without halting the core or requiring any target resident code. The SWJ-DP interface has the following features: ■ IEEE 1149.1-1990 compatible Test Access Port (TAP) controller ■ Four-bit Instruction Register (IR) chain for storing JTAG instructions ■ IEEE standard instructions: BYPASS, IDCODE, SAMPLE/PRELOAD, EXTEST and INTEST ■ ARM additional instructions: APACC, DPACC and ABORT ■ Integrated ARM Serial Wire Debug (SWD) – Serial Wire JTAG Debug Port (SWJ-DP) – Flash Patch and Breakpoint (FPB) unit for implementing breakpoints – Data Watchpoint and Trace (DWT) unit for implementing watchpoints, trigger resources, and system profiling November 08, 2011 67 Texas Instruments-Advance Information Architectural Overview – Instrumentation Trace Macrocell (ITM) for support of printf style debugging – Embedded Trace Macrocell (ETM) for instruction trace capture – Trace Port Interface Unit (TPIU) for bridging to a Trace Port Analyzer 1.3.8 Packaging and Temperature ■ Industrial-range (-40°C to 85°C) 157-ball RoHS-compliant BGA package 1.4 Hardware Details Details on the pins and package can be found in the following sections: ■ “Pin Diagram” on page 1356 ■ “Signal Tables” on page 1357 ■ “Operating Characteristics” on page 1408 ■ “Electrical Characteristics” on page 1409 ■ “Package Information” on page 1488 68 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 2 The Cortex-M4F Processor The ARM® Cortex™-M4F processor provides a high-performance, low-cost platform that meets the system requirements of minimal memory implementation, reduced pin count, and low power consumption, while delivering outstanding computational performance and exceptional system response to interrupts. Features include: ® ■ 32-bit ARM Cortex™-M4F architecture optimized for small-footprint embedded applications ■ 80-MHz operation; 100 DMIPS performance ■ Outstanding processing performance combined with fast interrupt handling ■ Thumb-2 mixed 16-/32-bit instruction set delivers the high performance expected of a 32-bit ARM core in a compact memory size usually associated with 8- and 16-bit devices, typically in the range of a few kilobytes of memory for microcontroller-class applications – Single-cycle multiply instruction and hardware divide – Atomic bit manipulation (bit-banding), delivering maximum memory utilization and streamlined peripheral control – Unaligned data access, enabling data to be efficiently packed into memory ■ IEEE754-compliant single-precision Floating-Point Unit (FPU) ■ 16-bit SIMD vector processing unit ■ Fast code execution permits slower processor clock or increases sleep mode time ■ Harvard architecture characterized by separate buses for instruction and data ■ Efficient processor core, system and memories ■ Hardware division and fast digital-signal-processing orientated multiply accumulate ■ Saturating arithmetic for signal processing ■ Deterministic, high-performance interrupt handling for time-critical applications ■ Memory protection unit (MPU) to provide a privileged mode for protected operating system functionality ■ Enhanced system debug with extensive breakpoint and trace capabilities ■ Serial Wire Debug and Serial Wire Trace reduce the number of pins required for debugging and tracing ■ Migration from the ARM7 processor family for better performance and power efficiency ■ Optimized for single-cycle Flash memory usage ■ Ultra-low power consumption with integrated sleep modes November 08, 2011 69 Texas Instruments-Advance Information The Cortex-M4F Processor ® The Stellaris family of microcontrollers builds on this core to bring high-performance 32-bit computing to cost-sensitive embedded microcontroller applications, such as factory automation and control, industrial control power devices, building and home automation, and stepper motor control. This chapter provides information on the Stellaris implementation of the Cortex-M4F processor, including the programming model, the memory model, the exception model, fault handling, and power management. For technical details on the instruction set, see the ARM® Cortex™-M4 Technical Reference Manual. 2.1 Block Diagram The Cortex-M4F processor is built on a high-performance processor core, with a 3-stage pipeline Harvard architecture, making it ideal for demanding embedded applications. The processor delivers exceptional power efficiency through an efficient instruction set and extensively optimized design, providing high-end processing hardware including IEEE754-compliant single-precision floating-point computation, a range of single-cycle and SIMD multiplication and multiply-with-accumulate capabilities, saturating arithmetic and dedicated hardware division. To facilitate the design of cost-sensitive devices, the Cortex-M4F processor implements tightly coupled system components that reduce processor area while significantly improving interrupt handling and system debug capabilities. The Cortex-M4F processor implements a version of the Thumb® instruction set based on Thumb-2 technology, ensuring high code density and reduced program memory requirements. The Cortex-M4F instruction set provides the exceptional performance expected of a modern 32-bit architecture, with the high code density of 8-bit and 16-bit microcontrollers. The Cortex-M4F processor closely integrates a nested interrupt controller (NVIC), to deliver industry-leading interrupt performance. The Stellaris NVIC includes a non-maskable interrupt (NMI) and provides eight interrupt priority levels. The tight integration of the processor core and NVIC provides fast execution of interrupt service routines (ISRs), dramatically reducing interrupt latency. The hardware stacking of registers and the ability to suspend load-multiple and store-multiple operations further reduce interrupt latency. Interrupt handlers do not require any assembler stubs which removes code overhead from the ISRs. Tail-chaining optimization also significantly reduces the overhead when switching from one ISR to another. To optimize low-power designs, the NVIC integrates with the sleep modes, including Deep-sleep mode, which enables the entire device to be rapidly powered down. 70 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 2-1. CPU Block Diagram Nested Vectored Interrupt Controller FPU Interrupts Sleep ARM Cortex-M4F CM4 Core Debug Instructions Data Embedded Trace Macrocell Memory Protection Unit Flash Patch and Breakpoint Instrumentation Data Watchpoint Trace Macrocell and Trace ROM Table Private Peripheral Bus (internal) Adv. Peripheral Bus Bus Matrix Serial Wire JTAG Debug Port Debug Access Port 2.2 Overview 2.2.1 System-Level Interface Trace Port Interface Unit Serial Wire Output Trace Port (SWO) I-code bus D-code bus System bus The Cortex-M4F processor provides multiple interfaces using AMBA® technology to provide high-speed, low-latency memory accesses. The core supports unaligned data accesses and implements atomic bit manipulation that enables faster peripheral controls, system spinlocks, and thread-safe Boolean data handling. The Cortex-M4F processor has a memory protection unit (MPU) that provides fine-grain memory control, enabling applications to implement security privilege levels and separate code, data and stack on a task-by-task basis. 2.2.2 Integrated Configurable Debug The Cortex-M4F processor implements a complete hardware debug solution, providing high system visibility of the processor and memory through either a traditional JTAG port or a 2-pin Serial Wire Debug (SWD) port that is ideal for microcontrollers and other small package devices. The Stellaris implementation replaces the ARM SW-DP and JTAG-DP with the ARM CoreSight™-compliant Serial Wire JTAG Debug Port (SWJ-DP) interface. The SWJ-DP interface combines the SWD and JTAG debug ports into one module. See the ARM® Debug Interface V5 Architecture Specification for details on SWJ-DP. For system trace, the processor integrates an Instrumentation Trace Macrocell (ITM) alongside data watchpoints and a profiling unit. To enable simple and cost-effective profiling of the system trace events, a Serial Wire Viewer (SWV) can export a stream of software-generated messages, data trace, and profiling information through a single pin. November 08, 2011 71 Texas Instruments-Advance Information The Cortex-M4F Processor The Embedded Trace Macrocell (ETM) delivers unrivaled instruction trace capture in an area smaller than traditional trace units, enabling full instruction trace. For more details on the ARM ETM, see the ARM® Embedded Trace Macrocell Architecture Specification. The Flash Patch and Breakpoint Unit (FPB) provides up to eight hardware breakpoint comparators that debuggers can use. The comparators in the FPB also provide remap functions of up to eight words in the program code in the CODE memory region. This enables applications stored in a read-only area of Flash memory to be patched in another area of on-chip SRAM or Flash memory. If a patch is required, the application programs the FPB to remap a number of addresses. When those addresses are accessed, the accesses are redirected to a remap table specified in the FPB configuration. For more information on the Cortex-M4F debug capabilities, see theARM® Debug Interface V5 Architecture Specification. 2.2.3 Trace Port Interface Unit (TPIU) The TPIU acts as a bridge between the Cortex-M4F trace data from the ITM, and an off-chip Trace Port Analyzer, as shown in Figure 2-2 on page 72. Figure 2-2. TPIU Block Diagram 2.2.4 Debug ATB Slave Port ATB Interface APB Slave Port APB Interface Asynchronous FIFO Trace Out (serializer) Serial Wire Trace Port (SWO) Cortex-M4F System Component Details The Cortex-M4F includes the following system components: ■ SysTick A 24-bit count-down timer that can be used as a Real-Time Operating System (RTOS) tick timer or as a simple counter (see “System Timer (SysTick)” on page 125). ■ Nested Vectored Interrupt Controller (NVIC) An embedded interrupt controller that supports low latency interrupt processing (see “Nested Vectored Interrupt Controller (NVIC)” on page 126). 72 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ System Control Block (SCB) The programming model interface to the processor. The SCB provides system implementation information and system control, including configuration, control, and reporting of system exceptions (see “System Control Block (SCB)” on page 127). ■ Memory Protection Unit (MPU) Improves system reliability by defining the memory attributes for different memory regions. The MPU provides up to eight different regions and an optional predefined background region (see “Memory Protection Unit (MPU)” on page 127). ■ Floating-Point Unit (FPU) Fully supports single-precision add, subtract, multiply, divide, multiply and accumulate, and square-root operations. It also provides conversions between fixed-point and floating-point data formats, and floating-point constant instructions. 2.3 Programming Model This section describes the Cortex-M4F programming model. In addition to the individual core register descriptions, information about the processor modes and privilege levels for software execution and stacks is included. 2.3.1 Processor Mode and Privilege Levels for Software Execution The Cortex-M4F has two modes of operation: ■ Thread mode Used to execute application software. The processor enters Thread mode when it comes out of reset. ■ Handler mode Used to handle exceptions. When the processor has finished exception processing, it returns to Thread mode. In addition, the Cortex-M4F has two privilege levels: ■ Unprivileged In this mode, software has the following restrictions: – Limited access to the MSR and MRS instructions and no use of the CPS instruction – No access to the system timer, NVIC, or system control block – Possibly restricted access to memory or peripherals ■ Privileged In this mode, software can use all the instructions and has access to all resources. In Thread mode, the CONTROL register (see page 88) controls whether software execution is privileged or unprivileged. In Handler mode, software execution is always privileged. November 08, 2011 73 Texas Instruments-Advance Information The Cortex-M4F Processor Only privileged software can write to the CONTROL register to change the privilege level for software execution in Thread mode. Unprivileged software can use the SVC instruction to make a supervisor call to transfer control to privileged software. 2.3.2 Stacks The processor uses a full descending stack, meaning that the stack pointer indicates the last stacked item on the memory. When the processor pushes a new item onto the stack, it decrements the stack pointer and then writes the item to the new memory location. The processor implements two stacks: the main stack and the process stack, with a pointer for each held in independent registers (see the SP register on page 78). In Thread mode, the CONTROL register (see page 88) controls whether the processor uses the main stack or the process stack. In Handler mode, the processor always uses the main stack. The options for processor operations are shown in Table 2-1 on page 74. Table 2-1. Summary of Processor Mode, Privilege Level, and Stack Use Processor Mode Use Privilege Level Thread Applications Privileged or unprivileged Handler Exception handlers Always privileged Stack Used a Main stack or process stack a Main stack a. See CONTROL (page 88). 2.3.3 Register Map Figure 2-3 on page 75 shows the Cortex-M4F register set. Table 2-2 on page 75 lists the Core registers. The core registers are not memory mapped and are accessed by register name, so the base address is n/a (not applicable) and there is no offset. 74 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 2-3. Cortex-M4F Register Set R0 R1 R2 R3 Low registers R4 R5 General-purpose registers R6 R7 R8 R9 High registers R10 R11 R12 Stack Pointer SP (R13) Link Register LR (R14) Program Counter PC (R15) PSP‡ PSR MSP‡ ‡ Banked version of SP Program status register PRIMASK FAULTMASK Exception mask registers Special registers BASEPRI CONTROL CONTROL register Table 2-2. Processor Register Map Offset Description See page Name Type Reset - R0 R/W - Cortex General-Purpose Register 0 77 - R1 R/W - Cortex General-Purpose Register 1 77 - R2 R/W - Cortex General-Purpose Register 2 77 - R3 R/W - Cortex General-Purpose Register 3 77 - R4 R/W - Cortex General-Purpose Register 4 77 - R5 R/W - Cortex General-Purpose Register 5 77 - R6 R/W - Cortex General-Purpose Register 6 77 - R7 R/W - Cortex General-Purpose Register 7 77 - R8 R/W - Cortex General-Purpose Register 8 77 - R9 R/W - Cortex General-Purpose Register 9 77 - R10 R/W - Cortex General-Purpose Register 10 77 - R11 R/W - Cortex General-Purpose Register 11 77 November 08, 2011 75 Texas Instruments-Advance Information The Cortex-M4F Processor Table 2-2. Processor Register Map (continued) Offset Type Reset - R12 R/W - Cortex General-Purpose Register 12 77 - SP R/W - Stack Pointer 78 - LR R/W 0xFFFF.FFFF Link Register 79 - PC R/W - Program Counter 80 - PSR R/W 0x0100.0000 Program Status Register 81 - PRIMASK R/W 0x0000.0000 Priority Mask Register 85 - FAULTMASK R/W 0x0000.0000 Fault Mask Register 86 - BASEPRI R/W 0x0000.0000 Base Priority Mask Register 87 - CONTROL R/W 0x0000.0000 Control Register 88 - FPSC R/W - Floating-Point Status Control 90 2.3.4 Description See page Name Register Descriptions This section lists and describes the Cortex-M4F registers, in the order shown in Figure 2-3 on page 75. The core registers are not memory mapped and are accessed by register name rather than offset. Note: The register type shown in the register descriptions refers to type during program execution in Thread mode and Handler mode. Debug access can differ. 76 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 1: Cortex General-Purpose Register 0 (R0) Register 2: Cortex General-Purpose Register 1 (R1) Register 3: Cortex General-Purpose Register 2 (R2) Register 4: Cortex General-Purpose Register 3 (R3) Register 5: Cortex General-Purpose Register 4 (R4) Register 6: Cortex General-Purpose Register 5 (R5) Register 7: Cortex General-Purpose Register 6 (R6) Register 8: Cortex General-Purpose Register 7 (R7) Register 9: Cortex General-Purpose Register 8 (R8) Register 10: Cortex General-Purpose Register 9 (R9) Register 11: Cortex General-Purpose Register 10 (R10) Register 12: Cortex General-Purpose Register 11 (R11) Register 13: Cortex General-Purpose Register 12 (R12) The Rn registers are 32-bit general-purpose registers for data operations and can be accessed from either privileged or unprivileged mode. Cortex General-Purpose Register 0 (R0) Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - DATA Type Reset DATA Type Reset Bit/Field Name Type Reset 31:0 DATA R/W - Description Register data. November 08, 2011 77 Texas Instruments-Advance Information The Cortex-M4F Processor Register 14: Stack Pointer (SP) The Stack Pointer (SP) is register R13. In Thread mode, the function of this register changes depending on the ASP bit in the Control Register (CONTROL) register. When the ASP bit is clear, this register is the Main Stack Pointer (MSP). When the ASP bit is set, this register is the Process Stack Pointer (PSP). On reset, the ASP bit is clear, and the processor loads the MSP with the value from address 0x0000.0000. The MSP can only be accessed in privileged mode; the PSP can be accessed in either privileged or unprivileged mode. Stack Pointer (SP) Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - SP Type Reset SP Type Reset Bit/Field Name Type Reset 31:0 SP R/W - Description This field is the address of the stack pointer. 78 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 15: Link Register (LR) The Link Register (LR) is register R14, and it stores the return information for subroutines, function calls, and exceptions. LR can be accessed from either privileged or unprivileged mode. EXC_RETURN is loaded into LR on exception entry. See Table 2-10 on page 112 for the values and description. Link Register (LR) Type R/W, reset 0xFFFF.FFFF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 LINK Type Reset R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 15 14 13 12 11 10 9 8 LINK Type Reset R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 Bit/Field Name Type 31:0 LINK R/W R/W 1 Reset R/W 1 Description 0xFFFF.FFFF This field is the return address. November 08, 2011 79 Texas Instruments-Advance Information The Cortex-M4F Processor Register 16: Program Counter (PC) The Program Counter (PC) is register R15, and it contains the current program address. On reset, the processor loads the PC with the value of the reset vector, which is at address 0x0000.0004. Bit 0 of the reset vector is loaded into the THUMB bit of the EPSR at reset and must be 1. The PC register can be accessed in either privileged or unprivileged mode. Program Counter (PC) Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - PC Type Reset PC Type Reset Bit/Field Name Type Reset 31:0 PC R/W - Description This field is the current program address. 80 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 17: Program Status Register (PSR) Note: This register is also referred to as xPSR. The Program Status Register (PSR) has three functions, and the register bits are assigned to the different functions: ■ Application Program Status Register (APSR), bits 31:27, bits 19:16 ■ Execution Program Status Register (EPSR), bits 26:24, 15:10 ■ Interrupt Program Status Register (IPSR), bits 7:0 The PSR, IPSR, and EPSR registers can only be accessed in privileged mode; the APSR register can be accessed in either privileged or unprivileged mode. APSR contains the current state of the condition flags from previous instruction executions. EPSR contains the Thumb state bit and the execution state bits for the If-Then (IT) instruction or the Interruptible-Continuable Instruction (ICI) field for an interrupted load multiple or store multiple instruction. Attempts to read the EPSR directly through application software using the MSR instruction always return zero. Attempts to write the EPSR using the MSR instruction in application software are always ignored. Fault handlers can examine the EPSR value in the stacked PSR to determine the operation that faulted (see “Exception Entry and Return” on page 109). IPSR contains the exception type number of the current Interrupt Service Routine (ISR). These registers can be accessed individually or as a combination of any two or all three registers, using the register name as an argument to the MSR or MRS instructions. For example, all of the registers can be read using PSR with the MRS instruction, or APSR only can be written to using APSR with the MSR instruction. page 81 shows the possible register combinations for the PSR. See the MRS and MSR instruction descriptions in the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information about how to access the program status registers. Table 2-3. PSR Register Combinations Register Type PSR R/W Combination APSR, EPSR, and IPSR IEPSR RO EPSR and IPSR a, b a APSR and IPSR b APSR and EPSR IAPSR R/W EAPSR R/W a. The processor ignores writes to the IPSR bits. b. Reads of the EPSR bits return zero, and the processor ignores writes to these bits. Program Status Register (PSR) Type R/W, reset 0x0100.0000 Type Reset 31 30 29 28 27 N Z C V Q 26 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 RO 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 ICI / IT Type Reset RO 0 RO 0 RO 0 25 ICI / IT 24 23 22 THUMB 21 RO 0 RO 0 RO 0 RO 0 19 18 17 16 R/W 0 R/W 0 R/W 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 GE reserved RO 0 20 reserved ISRNUM RO 0 RO 0 RO 0 November 08, 2011 RO 0 81 Texas Instruments-Advance Information The Cortex-M4F Processor Bit/Field Name Type Reset 31 N R/W 0 Description APSR Negative or Less Flag Value Description 1 The previous operation result was negative or less than. 0 The previous operation result was positive, zero, greater than, or equal. The value of this bit is only meaningful when accessing PSR or APSR. 30 Z R/W 0 APSR Zero Flag Value Description 1 The previous operation result was zero. 0 The previous operation result was non-zero. The value of this bit is only meaningful when accessing PSR or APSR. 29 C R/W 0 APSR Carry or Borrow Flag Value Description 1 The previous add operation resulted in a carry bit or the previous subtract operation did not result in a borrow bit. 0 The previous add operation did not result in a carry bit or the previous subtract operation resulted in a borrow bit. The value of this bit is only meaningful when accessing PSR or APSR. 28 V R/W 0 APSR Overflow Flag Value Description 1 The previous operation resulted in an overflow. 0 The previous operation did not result in an overflow. The value of this bit is only meaningful when accessing PSR or APSR. 27 Q R/W 0 APSR DSP Overflow and Saturation Flag Value Description 1 DSP Overflow or saturation has occurred. 0 DSP overflow or saturation has not occurred since reset or since the bit was last cleared. The value of this bit is only meaningful when accessing PSR or APSR. This bit is cleared by software using an MRS instruction. 82 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 26:25 ICI / IT RO 0x0 Description EPSR ICI / IT status These bits, along with bits 15:10, contain the Interruptible-Continuable Instruction (ICI) field for an interrupted load multiple or store multiple instruction or the execution state bits of the IT instruction. When EPSR holds the ICI execution state, bits 26:25 are zero. The If-Then block contains up to four instructions following an IT instruction. Each instruction in the block is conditional. The conditions for the instructions are either all the same, or some can be the inverse of others. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. The value of this field is only meaningful when accessing PSR or EPSR. 24 THUMB RO 1 EPSR Thumb State This bit indicates the Thumb state and should always be set. The following can clear the THUMB bit: ■ The BLX, BX and POP{PC} instructions ■ Restoration from the stacked xPSR value on an exception return ■ Bit 0 of the vector value on an exception entry or reset Attempting to execute instructions when this bit is clear results in a fault or lockup. See “Lockup” on page 114 for more information. The value of this bit is only meaningful when accessing PSR or EPSR. 23:20 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 19:16 GE R/W 0x0 Greater Than or Equal Flags See the description of the SEL instruction in the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. The value of this field is only meaningful when accessing PSR or APSR. 15:10 ICI / IT RO 0x0 EPSR ICI / IT status These bits, along with bits 26:25, contain the Interruptible-Continuable Instruction (ICI) field for an interrupted load multiple or store multiple instruction or the execution state bits of the IT instruction. When an interrupt occurs during the execution of an LDM, STM, PUSH POP, VLDM, VSTM, VPUSH, or VPOP instruction, the processor stops the load multiple or store multiple instruction operation temporarily and stores the next register operand in the multiple operation to bits 15:12. After servicing the interrupt, the processor returns to the register pointed to by bits 15:12 and resumes execution of the multiple load or store instruction. When EPSR holds the ICI execution state, bits 11:10 are zero. The If-Then block contains up to four instructions following a 16-bit IT instruction. Each instruction in the block is conditional. The conditions for the instructions are either all the same, or some can be the inverse of others. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. The value of this field is only meaningful when accessing PSR or EPSR. 9:8 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 83 Texas Instruments-Advance Information The Cortex-M4F Processor Bit/Field Name Type Reset Description 7:0 ISRNUM RO 0x00 IPSR ISR Number This field contains the exception type number of the current Interrupt Service Routine (ISR). Value Description 0x00 Thread mode 0x01 Reserved 0x02 NMI 0x03 Hard fault 0x04 Memory management fault 0x05 Bus fault 0x06 Usage fault 0x07-0x0A Reserved 0x0B SVCall 0x0C Reserved for Debug 0x0D Reserved 0x0E PendSV 0x0F SysTick 0x10 Interrupt Vector 0 0x11 Interrupt Vector 1 ... ... 0x93 Interrupt Vector 147 0x94-0x7F Reserved See “Exception Types” on page 102 for more information. The value of this field is only meaningful when accessing PSR or IPSR. 84 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 18: Priority Mask Register (PRIMASK) The PRIMASK register prevents activation of all exceptions with programmable priority. Reset, non-maskable interrupt (NMI), and hard fault are the only exceptions with fixed priority. Exceptions should be disabled when they might impact the timing of critical tasks. This register is only accessible in privileged mode. The MSR and MRS instructions are used to access the PRIMASK register, and the CPS instruction may be used to change the value of the PRIMASK register. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information on these instructions. For more information on exception priority levels, see “Exception Types” on page 102. Priority Mask Register (PRIMASK) Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 PRIMASK R/W 0 RO 0 PRIMASK R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Priority Mask Value Description 1 Prevents the activation of all exceptions with configurable priority. 0 No effect. November 08, 2011 85 Texas Instruments-Advance Information The Cortex-M4F Processor Register 19: Fault Mask Register (FAULTMASK) The FAULTMASK register prevents activation of all exceptions except for the Non-Maskable Interrupt (NMI). Exceptions should be disabled when they might impact the timing of critical tasks. This register is only accessible in privileged mode. The MSR and MRS instructions are used to access the FAULTMASK register, and the CPS instruction may be used to change the value of the FAULTMASK register. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information on these instructions. For more information on exception priority levels, see “Exception Types” on page 102. Fault Mask Register (FAULTMASK) Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 FAULTMASK R/W 0 RO 0 FAULTMASK R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Fault Mask Value Description 1 Prevents the activation of all exceptions except for NMI. 0 No effect. The processor clears the FAULTMASK bit on exit from any exception handler except the NMI handler. 86 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 20: Base Priority Mask Register (BASEPRI) The BASEPRI register defines the minimum priority for exception processing. When BASEPRI is set to a nonzero value, it prevents the activation of all exceptions with the same or lower priority level as the BASEPRI value. Exceptions should be disabled when they might impact the timing of critical tasks. This register is only accessible in privileged mode. For more information on exception priority levels, see “Exception Types” on page 102. Base Priority Mask Register (BASEPRI) Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset BASEPRI RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:5 BASEPRI R/W 0x0 R/W 0 reserved RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Base Priority Any exception that has a programmable priority level with the same or lower priority as the value of this field is masked. The PRIMASK register can be used to mask all exceptions with programmable priority levels. Higher priority exceptions have lower priority levels. Value Description 4:0 reserved RO 0x0 0x0 All exceptions are unmasked. 0x1 All exceptions with priority level 1-7 are masked. 0x2 All exceptions with priority level 2-7 are masked. 0x3 All exceptions with priority level 3-7 are masked. 0x4 All exceptions with priority level 4-7 are masked. 0x5 All exceptions with priority level 5-7 are masked. 0x6 All exceptions with priority level 6-7 are masked. 0x7 All exceptions with priority level 7 are masked. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 87 Texas Instruments-Advance Information The Cortex-M4F Processor Register 21: Control Register (CONTROL) The CONTROL register controls the stack used and the privilege level for software execution when the processor is in Thread mode, and indicates whether the FPU state is active. This register is only accessible in privileged mode. Handler mode always uses MSP, so the processor ignores explicit writes to the ASP bit of the CONTROL register when in Handler mode. The exception entry and return mechanisms automatically update the CONTROL register based on the EXC_RETURN value (see Table 2-10 on page 112). In an OS environment, threads running in Thread mode should use the process stack and the kernel and exception handlers should use the main stack. By default, Thread mode uses MSP. To switch the stack pointer used in Thread mode to PSP, either use the MSR instruction to set the ASP bit, as detailed in the Cortex™-M3/M4 Instruction Set Technical User's Manual, or perform an exception return to Thread mode with the appropriate EXC_RETURN value, as shown in Table 2-10 on page 112. Note: When changing the stack pointer, software must use an ISB instruction immediately after the MSR instruction, ensuring that instructions after the ISB execute use the new stack pointer. See the Cortex™-M3/M4 Instruction Set Technical User's Manual. Control Register (CONTROL) Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 FPCA ASP TMPL RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:3 reserved RO 0x0000.000 2 FPCA R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Floating-Point Context Active Value Description 1 Floating-point context active 0 No floating-point context active The Cortex-M4F uses this bit to determine whether to preserve floating-point state when processing an exception. Important: Two bits control when FPCA can be enabled: the ASPEN bit in the Floating-Point Context Control (FPCC) register and the DISFPCA bit in the Auxiliary Control (ACTLR) register. 88 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 ASP R/W 0 Description Active Stack Pointer Value Description 1 PSP is the current stack pointer. 0 MSP is the current stack pointer In Handler mode, this bit reads as zero and ignores writes. The Cortex-M4F updates this bit automatically on exception return. 0 TMPL R/W 0 Thread Mode Privilege Level Value Description 1 Unprivileged software can be executed in Thread mode. 0 Only privileged software can be executed in Thread mode. November 08, 2011 89 Texas Instruments-Advance Information The Cortex-M4F Processor Register 22: Floating-Point Status Control (FPSC) The FPSC register provides all necessary user-level control of the floating-point system. Floating-Point Status Control (FPSC) Type R/W, reset - Type Reset 31 30 29 28 27 26 25 24 22 21 20 19 RMODE 18 17 16 N Z C V AHP DN FZ R/W - R/W - R/W - R/W - RO 0 R/W - R/W - R/W - R/W - R/W - RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 IXC UFC OFC DZC IOC RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W - RO 0 R/W - R/W - R/W - R/W - R/W - reserved Type Reset 23 reserved IDC RO 0 Bit/Field Name Type Reset 31 N R/W - reserved reserved RO 0 Description Negative Condition Code Flag Floating-point comparison operations update this condition code flag. 30 Z R/W - Zero Condition Code Flag Floating-point comparison operations update this condition code flag. 29 C R/W - Carry Condition Code Flag Floating-point comparison operations update this condition code flag. 28 V R/W - Overflow Condition Code Flag Floating-point comparison operations update this condition code flag. 27 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 26 AHP R/W - Alternative Half-Precision When set, alternative half-precision format is selected. When clear, IEEE half-precision format is selected. The AHP bit in the FPDSC register holds the default value for this bit. 25 DN R/W - Default NaN Mode When set, any operation involving one or more NaNs returns the Default NaN. When clear, NaN operands propagate through to the output of a floating-point operation. The DN bit in the FPDSC register holds the default value for this bit. 24 FZ R/W - Flush-to-Zero Mode When set, Flush-to-Zero mode is enabled. When clear, Flush-to-Zero mode is disabled and the behavior of the floating-point system is fully compliant with the IEEE 754 standard. The FZ bit in the FPDSC register holds the default value for this bit. 90 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 23:22 RMODE R/W - Description Rounding Mode The specified rounding mode is used by almost all floating-point instructions. The RMODE bit in the FPDSC register holds the default value for this bit. Value Description 21:8 reserved RO 0x0 7 IDC R/W - 0x0 Round to Nearest (RN) mode 0x1 Round towards Plus Infinity (RP) mode 0x2 Round towards Minus Infinity (RM) mode 0x3 Round towards Zero (RZ) mode Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Input Denormal Cumulative Exception When set, indicates this exception has occurred since 0 was last written to this bit. 6:5 reserved RO 0x0 4 IXC R/W - Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Inexact Cumulative Exception When set, indicates this exception has occurred since 0 was last written to this bit. 3 UFC R/W - Underflow Cumulative Exception When set, indicates this exception has occurred since 0 was last written to this bit. 2 OFC R/W - Overflow Cumulative Exception When set, indicates this exception has occurred since 0 was last written to this bit. 1 DZC R/W - Division by Zero Cumulative Exception When set, indicates this exception has occurred since 0 was last written to this bit. 0 IOC R/W - Invalid Operation Cumulative Exception When set, indicates this exception has occurred since 0 was last written to this bit. November 08, 2011 91 Texas Instruments-Advance Information The Cortex-M4F Processor 2.3.5 Exceptions and Interrupts The Cortex-M4F processor supports interrupts and system exceptions. The processor and the Nested Vectored Interrupt Controller (NVIC) prioritize and handle all exceptions. An exception changes the normal flow of software control. The processor uses Handler mode to handle all exceptions except for reset. See “Exception Entry and Return” on page 109 for more information. The NVIC registers control interrupt handling. See “Nested Vectored Interrupt Controller (NVIC)” on page 126 for more information. 2.3.6 Data Types The Cortex-M4F supports 32-bit words, 16-bit halfwords, and 8-bit bytes. The processor also supports 64-bit data transfer instructions. All instruction and data memory accesses are little endian. See “Memory Regions, Types and Attributes” on page 95 for more information. 2.4 Memory Model This section describes the processor memory map, the behavior of memory accesses, and the bit-banding features. The processor has a fixed memory map that provides up to 4 GB of addressable memory. The memory map for the LM4F232H5BB controller is provided in Table 2-4 on page 92. In this manual, register addresses are given as a hexadecimal increment, relative to the module’s base address as shown in the memory map. The regions for SRAM and peripherals include bit-band regions. Bit-banding provides atomic operations to bit data (see “Bit-Banding” on page 97). The processor reserves regions of the Private peripheral bus (PPB) address range for core peripheral registers (see “Cortex-M4 Peripherals” on page 124). Note: Within the memory map, all reserved space returns a bus fault when read or written. Table 2-4. Memory Map Start End Description For details, see page ... 0x0000.0000 0x0003.FFFF On-chip Flash 556 0x0004.0000 0x00FF.FFFF Reserved - 0x0100.0000 0x1FFF.FFFF Reserved for ROM 554 0x2000.0000 0x2000.7FFF Bit-banded on-chip SRAM 553 0x2000.8000 0x21FF.FFFF Reserved - 0x2200.0000 0x220F.FFFF Bit-band alias of bit-banded on-chip SRAM starting at 0x2000.0000 553 0x2210.0000 0x3FFF.FFFF Reserved - 0x4000.0000 0x4000.0FFF Watchdog timer 0 807 0x4000.1000 0x4000.1FFF Watchdog timer 1 807 0x4000.2000 0x4000.3FFF Reserved - 0x4000.4000 0x4000.4FFF GPIO Port A 687 0x4000.5000 0x4000.5FFF GPIO Port B 687 0x4000.6000 0x4000.6FFF GPIO Port C 687 Memory FiRM Peripherals 92 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 2-4. Memory Map (continued) Start End Description For details, see page ... 0x4000.7000 0x4000.7FFF GPIO Port D 687 0x4000.8000 0x4000.8FFF SSI0 999 0x4000.9000 0x4000.9FFF SSI1 999 0x4000.A000 0x4000.AFFF SSI2 999 0x4000.B000 0x4000.BFFF SSI3 999 0x4000.C000 0x4000.CFFF UART0 931 0x4000.D000 0x4000.DFFF UART1 931 0x4000.E000 0x4000.EFFF UART2 931 0x4000.F000 0x4000.FFFF UART3 931 0x4001.0000 0x4001.0FFF UART4 931 0x4001.1000 0x4001.1FFF UART5 931 0x4001.2000 0x4001.2FFF UART6 931 0x4001.3000 0x4001.3FFF UART7 931 0x4001.4000 0x4001.FFFF Reserved - 0x4002.0000 0x4002.0FFF I2C 0 1045 0x4002.1000 0x4002.1FFF I2C 1 1045 0x4002.2FFF I2C 2 1045 3 1045 Peripherals 0x4002.2000 0x4002.3000 0x4002.3FFF I2C 0x4002.4000 0x4002.4FFF GPIO Port E 687 0x4002.5000 0x4002.5FFF GPIO Port F 687 0x4002.6000 0x4002.6FFF GPIO Port G 687 0x4002.7000 0x4002.7FFF GPIO Port H 687 0x4002.8000 0x4002.8FFF PWM 0 1268 0x4002.9000 0x4002.9FFF PWM 1 1268 0x4002.A000 0x4002.BFFF Reserved - 0x4002.C000 0x4002.CFFF QEI0 1339 0x4002.D000 0x4002.DFFF QEI1 1339 0x4002.E000 0x4002.FFFF Reserved - 0x4003.0000 0x4003.0FFF 16/32-bit Timer 0 757 0x4003.1000 0x4003.1FFF 16/32-bit Timer 1 757 0x4003.2000 0x4003.2FFF 16/32-bit Timer 2 757 0x4003.3000 0x4003.3FFF 16/32-bit Timer 3 757 0x4003.4000 0x4003.4FFF 16/32-bit Timer 4 757 0x4003.5000 0x4003.5FFF 16/32-bit Timer 5 757 0x4003.6000 0x4003.6FFF 32/64-bit Timer 0 757 0x4003.7000 0x4003.7FFF 32/64-bit Timer 1 757 0x4003.8000 0x4003.8FFF ADC0 849 0x4003.9000 0x4003.9FFF ADC1 849 0x4003.A000 0x4003.BFFF Reserved - 0x4003.C000 0x4003.CFFF Analog Comparators 1239 November 08, 2011 93 Texas Instruments-Advance Information The Cortex-M4F Processor Table 2-4. Memory Map (continued) Start End Description For details, see page ... 0x4003.D000 0x4003.DFFF GPIO Port J 687 0x4003.E000 0x4003.FFFF Reserved - 0x4004.0000 0x4004.0FFF CAN0 Controller 1093 0x4004.1000 0x4004.1FFF CAN1 Controller 1093 0x4004.2000 0x4004.BFFF Reserved - 0x4004.C000 0x4004.CFFF 32/64-bit Timer 2 757 0x4004.D000 0x4004.DFFF 32/64-bit Timer 3 757 0x4004.E000 0x4004.EFFF 32/64-bit Timer 4 757 0x4004.F000 0x4004.FFFF 32/64-bit Timer 5 757 0x4005.0000 0x4005.0FFF USB 1145 0x4005.1000 0x4005.7FFF Reserved - 0x4005.8000 0x4005.8FFF GPIO Port A (AHB aperture) 687 0x4005.9000 0x4005.9FFF GPIO Port B (AHB aperture) 687 0x4005.A000 0x4005.AFFF GPIO Port C (AHB aperture) 687 0x4005.B000 0x4005.BFFF GPIO Port D (AHB aperture) 687 0x4005.C000 0x4005.CFFF GPIO Port E (AHB aperture) 687 0x4005.D000 0x4005.DFFF GPIO Port F (AHB aperture) 687 0x4005.E000 0x4005.EFFF GPIO Port G (AHB aperture) 687 0x4005.F000 0x4005.FFFF GPIO Port H (AHB aperture) 687 0x4006.0000 0x4006.0FFF GPIO Port J (AHB aperture) 687 0x4006.1000 0x4006.1FFF GPIO Port K (AHB aperture) 687 0x4006.2000 0x4006.2FFF GPIO Port L (AHB aperture) 687 0x4006.3000 0x4006.3FFF GPIO Port M (AHB aperture) 687 0x4006.4000 0x4006.4FFF GPIO Port N (AHB aperture) 687 0x4006.5000 0x4006.5FFF GPIO Port P (AHB aperture) 687 0x4006.6000 0x4006.6FFF GPIO Port Q (AHB aperture) 687 0x4006.7000 0x400A.EFFF Reserved - 0x400A.F000 0x400A.FFFF EEPROM and Key Locker 585 0x400B.0000 0x400B.FFFF Reserved - 0x400C.0000 0x400C.0FFF I2C 4 1045 0x400C.1000 0x400C.1FFF I2C 1045 0x400C.2000 0x400F.8FFF Reserved - 0x400F.9000 0x400F.9FFF System Exception Module 514 0x400F.A000 0x400F.BFFF Reserved - 0x400F.C000 0x400F.CFFF Hibernation Module 534 0x400F.D000 0x400F.DFFF Flash memory control 567 0x400F.E000 0x400F.EFFF System control 236 0x400F.F000 0x400F.FFFF µDMA 631 0x4010.0000 0x41FF.FFFF Reserved - 0x4200.0000 0x43FF.FFFF Bit-banded alias of 0x4000.0000 through 0x400F.FFFF - 0x4400.0000 0xDFFF.FFFF Reserved - 5 94 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 2-4. Memory Map (continued) Start End Description For details, see page ... 0xE000.0000 0xE000.0FFF Instrumentation Trace Macrocell (ITM) 71 0xE000.1000 0xE000.1FFF Data Watchpoint and Trace (DWT) 71 0xE000.2000 0xE000.2FFF Flash Patch and Breakpoint (FPB) 71 0xE000.3000 0xE000.DFFF Reserved - 0xE000.E000 0xE000.EFFF Cortex-M4F Peripherals (SysTick, NVIC, MPU, FPU and SCB) 136 0xE000.F000 0xE003.FFFF Reserved - 0xE004.0000 0xE004.0FFF Trace Port Interface Unit (TPIU) 72 0xE004.1000 0xE004.1FFF Embedded Trace Macrocell (ETM) 71 0xE004.2000 0xFFFF.FFFF Reserved - Private Peripheral Bus 2.4.1 Memory Regions, Types and Attributes The memory map and the programming of the MPU split the memory map into regions. Each region has a defined memory type, and some regions have additional memory attributes. The memory type and attributes determine the behavior of accesses to the region. The memory types are: ■ Normal: The processor can re-order transactions for efficiency and perform speculative reads. ■ Device: The processor preserves transaction order relative to other transactions to Device or Strongly Ordered memory. ■ Strongly Ordered: The processor preserves transaction order relative to all other transactions. The different ordering requirements for Device and Strongly Ordered memory mean that the memory system can buffer a write to Device memory but must not buffer a write to Strongly Ordered memory. An additional memory attribute is Execute Never (XN), which means the processor prevents instruction accesses. A fault exception is generated only on execution of an instruction executed from an XN region. 2.4.2 Memory System Ordering of Memory Accesses For most memory accesses caused by explicit memory access instructions, the memory system does not guarantee that the order in which the accesses complete matches the program order of the instructions, providing the order does not affect the behavior of the instruction sequence. Normally, if correct program execution depends on two memory accesses completing in program order, software must insert a memory barrier instruction between the memory access instructions (see “Software Ordering of Memory Accesses” on page 96). However, the memory system does guarantee ordering of accesses to Device and Strongly Ordered memory. For two memory access instructions A1 and A2, if both A1 and A2 are accesses to either Device or Strongly Ordered memory, and if A1 occurs before A2 in program order, A1 is always observed before A2. 2.4.3 Behavior of Memory Accesses Table 2-5 on page 96 shows the behavior of accesses to each region in the memory map. See “Memory Regions, Types and Attributes” on page 95 for more information on memory types and November 08, 2011 95 Texas Instruments-Advance Information The Cortex-M4F Processor the XN attribute. Stellaris devices may have reserved memory areas within the address ranges shown below (refer to Table 2-4 on page 92 for more information). Table 2-5. Memory Access Behavior Address Range Memory Region Memory Type Execute Never (XN) Description 0x0000.0000 - 0x1FFF.FFFF Code Normal - This executable region is for program code. Data can also be stored here. 0x2000.0000 - 0x3FFF.FFFF SRAM Normal - This executable region is for data. Code can also be stored here. This region includes bit band and bit band alias areas (see Table 2-6 on page 98). 0x4000.0000 - 0x5FFF.FFFF Peripheral Device XN This region includes bit band and bit band alias areas (see Table 2-7 on page 98). 0x6000.0000 - 0x9FFF.FFFF External RAM Normal - This executable region is for data. 0xA000.0000 - 0xDFFF.FFFF External device Device XN This region is for external device memory. 0xE000.0000- 0xE00F.FFFF Private peripheral bus Strongly Ordered XN This region includes the NVIC, system timer, and system control block. 0xE010.0000- 0xFFFF.FFFF Reserved - - - The Code, SRAM, and external RAM regions can hold programs. However, it is recommended that programs always use the Code region because the Cortex-M4F has separate buses that can perform instruction fetches and data accesses simultaneously. The MPU can override the default memory access behavior described in this section. For more information, see “Memory Protection Unit (MPU)” on page 127. The Cortex-M4F prefetches instructions ahead of execution and speculatively prefetches from branch target addresses. 2.4.4 Software Ordering of Memory Accesses The order of instructions in the program flow does not always guarantee the order of the corresponding memory transactions for the following reasons: ■ The processor can reorder some memory accesses to improve efficiency, providing this does not affect the behavior of the instruction sequence. ■ The processor has multiple bus interfaces. ■ Memory or devices in the memory map have different wait states. ■ Some memory accesses are buffered or speculative. “Memory System Ordering of Memory Accesses” on page 95 describes the cases where the memory system guarantees the order of memory accesses. Otherwise, if the order of memory accesses is critical, software must include memory barrier instructions to force that ordering. The Cortex-M4F has the following memory barrier instructions: ■ The Data Memory Barrier (DMB) instruction ensures that outstanding memory transactions complete before subsequent memory transactions. 96 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ The Data Synchronization Barrier (DSB) instruction ensures that outstanding memory transactions complete before subsequent instructions execute. ■ The Instruction Synchronization Barrier (ISB) instruction ensures that the effect of all completed memory transactions is recognizable by subsequent instructions. Memory barrier instructions can be used in the following situations: ■ MPU programming – If the MPU settings are changed and the change must be effective on the very next instruction, use a DSB instruction to ensure the effect of the MPU takes place immediately at the end of context switching. – Use an ISB instruction to ensure the new MPU setting takes effect immediately after programming the MPU region or regions, if the MPU configuration code was accessed using a branch or call. If the MPU configuration code is entered using exception mechanisms, then an ISB instruction is not required. ■ Vector table If the program changes an entry in the vector table and then enables the corresponding exception, use a DMB instruction between the operations. The DMB instruction ensures that if the exception is taken immediately after being enabled, the processor uses the new exception vector. ■ Self-modifying code If a program contains self-modifying code, use an ISB instruction immediately after the code modification in the program. The ISB instruction ensures subsequent instruction execution uses the updated program. ■ Memory map switching If the system contains a memory map switching mechanism, use a DSB instruction after switching the memory map in the program. The DSB instruction ensures subsequent instruction execution uses the updated memory map. ■ Dynamic exception priority change When an exception priority has to change when the exception is pending or active, use DSB instructions after the change. The change then takes effect on completion of the DSB instruction. Memory accesses to Strongly Ordered memory, such as the System Control Block, do not require the use of DMB instructions. For more information on the memory barrier instructions, see the Cortex™-M3/M4 Instruction Set Technical User's Manual. 2.4.5 Bit-Banding A bit-band region maps each word in a bit-band alias region to a single bit in the bit-band region. The bit-band regions occupy the lowest 1 MB of the SRAM and peripheral memory regions. Accesses to the 32-MB SRAM alias region map to the 1-MB SRAM bit-band region, as shown in Table 2-6 on page 98. Accesses to the 32-MB peripheral alias region map to the 1-MB peripheral bit-band region, as shown in Table 2-7 on page 98. For the specific address range of the bit-band regions, see Table 2-4 on page 92. November 08, 2011 97 Texas Instruments-Advance Information The Cortex-M4F Processor Note: A word access to the SRAM or the peripheral bit-band alias region maps to a single bit in the SRAM or peripheral bit-band region. A word access to a bit band address results in a word access to the underlying memory, and similarly for halfword and byte accesses. This allows bit band accesses to match the access requirements of the underlying peripheral. Table 2-6. SRAM Memory Bit-Banding Regions Address Range Memory Region Instruction and Data Accesses 0x2000.0000 - 0x200F.FFFF SRAM bit-band region Direct accesses to this memory range behave as SRAM memory accesses, but this region is also bit addressable through bit-band alias. 0x2200.0000 - 0x23FF.FFFF SRAM bit-band alias Data accesses to this region are remapped to bit band region. A write operation is performed as read-modify-write. Instruction accesses are not remapped. Table 2-7. Peripheral Memory Bit-Banding Regions Address Range Memory Region Instruction and Data Accesses 0x4000.0000 - 0x400F.FFFF Peripheral bit-band region Direct accesses to this memory range behave as peripheral memory accesses, but this region is also bit addressable through bit-band alias. 0x4200.0000 - 0x43FF.FFFF Peripheral bit-band alias Data accesses to this region are remapped to bit band region. A write operation is performed as read-modify-write. Instruction accesses are not permitted. The following formula shows how the alias region maps onto the bit-band region: bit_word_offset = (byte_offset x 32) + (bit_number x 4) bit_word_addr = bit_band_base + bit_word_offset where: bit_word_offset The position of the target bit in the bit-band memory region. bit_word_addr The address of the word in the alias memory region that maps to the targeted bit. bit_band_base The starting address of the alias region. byte_offset The number of the byte in the bit-band region that contains the targeted bit. bit_number The bit position, 0-7, of the targeted bit. Figure 2-4 on page 99 shows examples of bit-band mapping between the SRAM bit-band alias region and the SRAM bit-band region: ■ The alias word at 0x23FF.FFE0 maps to bit 0 of the bit-band byte at 0x200F.FFFF: 0x23FF.FFE0 = 0x2200.0000 + (0x000F.FFFF*32) + (0*4) 98 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ The alias word at 0x23FF.FFFC maps to bit 7 of the bit-band byte at 0x200F.FFFF: 0x23FF.FFFC = 0x2200.0000 + (0x000F.FFFF*32) + (7*4) ■ The alias word at 0x2200.0000 maps to bit 0 of the bit-band byte at 0x2000.0000: 0x2200.0000 = 0x2200.0000 + (0*32) + (0*4) ■ The alias word at 0x2200.001C maps to bit 7 of the bit-band byte at 0x2000.0000: 0x2200.001C = 0x2200.0000+ (0*32) + (7*4) Figure 2-4. Bit-Band Mapping 32-MB Alias Region 0x23FF.FFFC 0x23FF.FFF8 0x23FF.FFF4 0x23FF.FFF0 0x23FF.FFEC 0x23FF.FFE8 0x23FF.FFE4 0x23FF.FFE0 0x2200.001C 0x2200.0018 0x2200.0014 0x2200.0010 0x2200.000C 0x2200.0008 0x2200.0004 0x2200.0000 7 3 1-MB SRAM Bit-Band Region 7 6 5 4 3 2 1 0 7 6 0x200F.FFFF 7 6 5 4 3 2 0x2000.0003 2.4.5.1 5 4 3 2 1 0 7 6 0x200F.FFFE 1 0 7 6 5 4 3 2 5 4 3 2 1 0 6 0x200F.FFFD 1 0 0x2000.0002 7 6 5 4 3 2 5 4 2 1 0 1 0 0x200F.FFFC 1 0x2000.0001 0 7 6 5 4 3 2 0x2000.0000 Directly Accessing an Alias Region Writing to a word in the alias region updates a single bit in the bit-band region. Bit 0 of the value written to a word in the alias region determines the value written to the targeted bit in the bit-band region. Writing a value with bit 0 set writes a 1 to the bit-band bit, and writing a value with bit 0 clear writes a 0 to the bit-band bit. Bits 31:1 of the alias word have no effect on the bit-band bit. Writing 0x01 has the same effect as writing 0xFF. Writing 0x00 has the same effect as writing 0x0E. When reading a word in the alias region, 0x0000.0000 indicates that the targeted bit in the bit-band region is clear and 0x0000.0001 indicates that the targeted bit in the bit-band region is set. 2.4.5.2 Directly Accessing a Bit-Band Region “Behavior of Memory Accesses” on page 95 describes the behavior of direct byte, halfword, or word accesses to the bit-band regions. November 08, 2011 99 Texas Instruments-Advance Information The Cortex-M4F Processor 2.4.6 Data Storage The processor views memory as a linear collection of bytes numbered in ascending order from zero. For example, bytes 0-3 hold the first stored word, and bytes 4-7 hold the second stored word. Data is stored in little-endian format, with the least-significant byte (lsbyte) of a word stored at the lowest-numbered byte, and the most-significant byte (msbyte) stored at the highest-numbered byte. Figure 2-5 on page 100 illustrates how data is stored. Figure 2-5. Data Storage Memory 7 Register 0 31 2.4.7 Address A B0 A+1 B1 A+2 B2 A+3 B3 lsbyte 24 23 B3 16 15 B2 8 7 B1 0 B0 msbyte Synchronization Primitives The Cortex-M4F instruction set includes pairs of synchronization primitives which provide a non-blocking mechanism that a thread or process can use to obtain exclusive access to a memory location. Software can use these primitives to perform a guaranteed read-modify-write memory update sequence or for a semaphore mechanism. A pair of synchronization primitives consists of: ■ A Load-Exclusive instruction, which is used to read the value of a memory location and requests exclusive access to that location. ■ A Store-Exclusive instruction, which is used to attempt to write to the same memory location and returns a status bit to a register. If this status bit is clear, it indicates that the thread or process gained exclusive access to the memory and the write succeeds; if this status bit is set, it indicates that the thread or process did not gain exclusive access to the memory and no write was performed. The pairs of Load-Exclusive and Store-Exclusive instructions are: ■ The word instructions LDREX and STREX ■ The halfword instructions LDREXH and STREXH ■ The byte instructions LDREXB and STREXB Software must use a Load-Exclusive instruction with the corresponding Store-Exclusive instruction. To perform an exclusive read-modify-write of a memory location, software must: 1. Use a Load-Exclusive instruction to read the value of the location. 2. Modify the value, as required. 100 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 3. Use a Store-Exclusive instruction to attempt to write the new value back to the memory location. 4. Test the returned status bit. If the status bit is clear, the read-modify-write completed successfully. If the status bit is set, no write was performed, which indicates that the value returned at step 1 might be out of date. The software must retry the entire read-modify-write sequence. Software can use the synchronization primitives to implement a semaphore as follows: 1. Use a Load-Exclusive instruction to read from the semaphore address to check whether the semaphore is free. 2. If the semaphore is free, use a Store-Exclusive to write the claim value to the semaphore address. 3. If the returned status bit from step 2 indicates that the Store-Exclusive succeeded, then the software has claimed the semaphore. However, if the Store-Exclusive failed, another process might have claimed the semaphore after the software performed step 1. The Cortex-M4F includes an exclusive access monitor that tags the fact that the processor has executed a Load-Exclusive instruction. The processor removes its exclusive access tag if: ■ It executes a CLREX instruction. ■ It executes a Store-Exclusive instruction, regardless of whether the write succeeds. ■ An exception occurs, which means the processor can resolve semaphore conflicts between different threads. For more information about the synchronization primitive instructions, see the Cortex™-M3/M4 Instruction Set Technical User's Manual. 2.5 Exception Model The ARM Cortex-M4F processor and the Nested Vectored Interrupt Controller (NVIC) prioritize and handle all exceptions in Handler Mode. The processor state is automatically stored to the stack on an exception and automatically restored from the stack at the end of the Interrupt Service Routine (ISR). The vector is fetched in parallel to the state saving, enabling efficient interrupt entry. The processor supports tail-chaining, which enables back-to-back interrupts to be performed without the overhead of state saving and restoration. Table 2-8 on page 103 lists all exception types. Software can set eight priority levels on seven of these exceptions (system handlers) as well as on 104 interrupts (listed in Table 2-9 on page 104). Priorities on the system handlers are set with the NVIC System Handler Priority n (SYSPRIn) registers. Interrupts are enabled through the NVIC Interrupt Set Enable n (ENn) register and prioritized with the NVIC Interrupt Priority n (PRIn) registers. Priorities can be grouped by splitting priority levels into preemption priorities and subpriorities. All the interrupt registers are described in “Nested Vectored Interrupt Controller (NVIC)” on page 126. Internally, the highest user-programmable priority (0) is treated as fourth priority, after a Reset, Non-Maskable Interrupt (NMI), and a Hard Fault, in that order. Note that 0 is the default priority for all the programmable priorities. November 08, 2011 101 Texas Instruments-Advance Information The Cortex-M4F Processor Important: After a write to clear an interrupt source, it may take several processor cycles for the NVIC to see the interrupt source de-assert. Thus if the interrupt clear is done as the last action in an interrupt handler, it is possible for the interrupt handler to complete while the NVIC sees the interrupt as still asserted, causing the interrupt handler to be re-entered errantly. This situation can be avoided by either clearing the interrupt source at the beginning of the interrupt handler or by performing a read or write after the write to clear the interrupt source (and flush the write buffer). See “Nested Vectored Interrupt Controller (NVIC)” on page 126 for more information on exceptions and interrupts. 2.5.1 Exception States Each exception is in one of the following states: ■ Inactive. The exception is not active and not pending. ■ Pending. The exception is waiting to be serviced by the processor. An interrupt request from a peripheral or from software can change the state of the corresponding interrupt to pending. ■ Active. An exception that is being serviced by the processor but has not completed. Note: An exception handler can interrupt the execution of another exception handler. In this case, both exceptions are in the active state. ■ Active and Pending. The exception is being serviced by the processor, and there is a pending exception from the same source. 2.5.2 Exception Types The exception types are: ■ Reset. Reset is invoked on power up or a warm reset. The exception model treats reset as a special form of exception. When reset is asserted, the operation of the processor stops, potentially at any point in an instruction. When reset is deasserted, execution restarts from the address provided by the reset entry in the vector table. Execution restarts as privileged execution in Thread mode. ■ NMI. A non-maskable Interrupt (NMI) can be signaled using the NMI signal or triggered by software using the Interrupt Control and State (INTCTRL) register. This exception has the highest priority other than reset. NMI is permanently enabled and has a fixed priority of -2. NMIs cannot be masked or prevented from activation by any other exception or preempted by any exception other than reset. ■ Hard Fault. A hard fault is an exception that occurs because of an error during exception processing, or because an exception cannot be managed by any other exception mechanism. Hard faults have a fixed priority of -1, meaning they have higher priority than any exception with configurable priority. ■ Memory Management Fault. A memory management fault is an exception that occurs because of a memory protection related fault, including access violation and no match. The MPU or the fixed memory protection constraints determine this fault, for both instruction and data memory transactions. This fault is used to abort instruction accesses to Execute Never (XN) memory regions, even if the MPU is disabled. 102 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Bus Fault. A bus fault is an exception that occurs because of a memory-related fault for an instruction or data memory transaction such as a prefetch fault or a memory access fault. This fault can be enabled or disabled. ■ Usage Fault. A usage fault is an exception that occurs because of a fault related to instruction execution, such as: – An undefined instruction – An illegal unaligned access – Invalid state on instruction execution – An error on exception return An unaligned address on a word or halfword memory access or division by zero can cause a usage fault when the core is properly configured. ■ SVCall. A supervisor call (SVC) is an exception that is triggered by the SVC instruction. In an OS environment, applications can use SVC instructions to access OS kernel functions and device drivers. ■ Debug Monitor. This exception is caused by the debug monitor (when not halting). This exception is only active when enabled. This exception does not activate if it is a lower priority than the current activation. ■ PendSV. PendSV is a pendable, interrupt-driven request for system-level service. In an OS environment, use PendSV for context switching when no other exception is active. PendSV is triggered using the Interrupt Control and State (INTCTRL) register. ■ SysTick. A SysTick exception is an exception that the system timer generates when it reaches zero when it is enabled to generate an interrupt. Software can also generate a SysTick exception using the Interrupt Control and State (INTCTRL) register. In an OS environment, the processor can use this exception as system tick. ■ Interrupt (IRQ). An interrupt, or IRQ, is an exception signaled by a peripheral or generated by a software request and fed through the NVIC (prioritized). All interrupts are asynchronous to instruction execution. In the system, peripherals use interrupts to communicate with the processor. Table 2-9 on page 104 lists the interrupts on the LM4F232H5BB controller. For an asynchronous exception, other than reset, the processor can execute another instruction between when the exception is triggered and when the processor enters the exception handler. Privileged software can disable the exceptions that Table 2-8 on page 103 shows as having configurable priority (see the SYSHNDCTRL register on page 175 and the DIS0 register on page 146). For more information about hard faults, memory management faults, bus faults, and usage faults, see “Fault Handling” on page 112. Table 2-8. Exception Types Exception Type a Vector Number Priority Vector Address or b Offset - 0 - 0x0000.0000 Stack top is loaded from the first entry of the vector table on reset. Reset 1 -3 (highest) 0x0000.0004 Asynchronous November 08, 2011 Activation 103 Texas Instruments-Advance Information The Cortex-M4F Processor Table 2-8. Exception Types (continued) Exception Type a Vector Number Priority Vector Address or b Offset Non-Maskable Interrupt (NMI) 2 -2 0x0000.0008 Asynchronous Hard Fault 3 -1 Memory Management 4 0x0000.000C - c 0x0000.0010 Synchronous c 0x0000.0014 Synchronous when precise and asynchronous when imprecise c programmable Bus Fault 5 programmable Usage Fault 6 programmable 0x0000.0018 7-10 - - 11 programmable SVCall c 0x0000.002C c Debug Monitor 12 programmable 0x0000.0030 - 13 - - PendSV 14 programmable SysTick Interrupts Activation c c 15 programmable 16 and above programmable d Synchronous Reserved Synchronous Synchronous Reserved 0x0000.0038 Asynchronous 0x0000.003C Asynchronous 0x0000.0040 and above Asynchronous a. 0 is the default priority for all the programmable priorities. b. See “Vector Table” on page 107. c. See SYSPRI1 on page 172. d. See PRIn registers on page 154. Table 2-9. Interrupts Vector Number Interrupt Number (Bit in Interrupt Registers) Vector Address or Offset Description 0-15 - 0x0000.0000 0x0000.003C 16 0 0x0000.0040 GPIO Port A 17 1 0x0000.0044 GPIO Port B 18 2 0x0000.0048 GPIO Port C 19 3 0x0000.004C GPIO Port D 20 4 0x0000.0050 GPIO Port E 21 5 0x0000.0054 UART0 22 6 0x0000.0058 UART1 23 7 0x0000.005C SSI0 24 8 0x0000.0060 I2C0 25 9 0x0000.0064 PWM0 Fault 26 10 0x0000.0068 PWM0 Generator 0 27 11 0x0000.006C PWM0 Generator 1 28 12 0x0000.0070 PWM0 Generator 2 29 13 0x0000.0074 QEI0 30 14 0x0000.0078 ADC0 Sequence 0 31 15 0x0000.007C ADC0 Sequence 1 32 16 0x0000.0080 ADC0 Sequence 2 33 17 0x0000.0084 ADC0 Sequence 3 Processor exceptions 104 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 2-9. Interrupts (continued) Vector Number Interrupt Number (Bit in Interrupt Registers) Vector Address or Offset Description 34 18 0x0000.0088 Watchdog Timers 0 and 1 35 19 0x0000.008C 16/32-Bit Timer 0A 36 20 0x0000.0090 16/32-Bit Timer 0B 37 21 0x0000.0094 16/32-Bit Timer 1A 38 22 0x0000.0098 16/32-Bit Timer 1B 39 23 0x0000.009C 16/32-Bit Timer 2A 40 24 0x0000.00A0 16/32-Bit Timer 2B 41 25 0x0000.00A4 Analog Comparator 0 42 26 0x0000.00A8 Analog Comparator 1 43 27 0x0000.00AC Analog Comparator 2 44 28 0x0000.00B0 System Control 45 29 0x0000.00B4 Flash Memory Control and EEPROM Control 46 30 0x0000.00B8 GPIO Port F 47 31 0x0000.00BC GPIO Port G 48 32 0x0000.00C0 GPIO Port H 49 33 0x0000.00C4 UART2 50 34 0x0000.00C8 SSI1 51 35 0x0000.00CC 16/32-Bit Timer 3A 52 36 0x0000.00D0 16/32-Bit Timer 3B 53 37 0x0000.00D4 I2C1 54 38 0x0000.00D8 QEI1 55 39 0x0000.00DC CAN0 CAN1 56 40 0x0000.00E0 57-58 41-42 - 59 43 0x0000.00EC Hibernation Module 60 44 0x0000.00F0 USB 61 45 0x0000.00F4 PWM Generator 3 62 46 0x0000.00F8 µDMA Software 63 47 0x0000.00FC µDMA Error 64 48 0x0000.0100 ADC1 Sequence 0 65 49 0x0000.0104 ADC1 Sequence 1 66 50 0x0000.0108 ADC1 Sequence 2 67 51 0x0000.010C ADC1 Sequence 3 68-69 52-53 - 70 54 0x0000.0118 GPIO Port J 71 55 0x0000.011C GPIO Port K 72 56 0x0000.0120 GPIO Port L 73 57 0x0000.0124 SSI2 74 58 0x0000.0128 SSI3 75 59 0x0000.012C UART3 76 60 0x0000.0130 UART4 Reserved Reserved November 08, 2011 105 Texas Instruments-Advance Information The Cortex-M4F Processor Table 2-9. Interrupts (continued) Vector Number Interrupt Number (Bit in Interrupt Registers) Vector Address or Offset Description 77 61 0x0000.0134 UART5 78 62 0x0000.0138 UART6 79 63 0x0000.013C UART7 80-83 64-67 0x0000.0140 0x0000.014C Reserved 84 68 0x0000.0150 I2C2 85 69 0x0000.0154 I2C3 86 70 0x0000.0158 16/32-Bit Timer 4A 87 71 0x0000.015C 16/32-Bit Timer 4B 88-107 72-91 0x0000.0160 0x0000.01AC Reserved 108 92 0x0000.01B0 16/32-Bit Timer 5A 109 93 0x0000.01B4 16/32-Bit Timer 5B 110 94 0x0000.01B8 32/64-Bit Timer 0A 111 95 0x0000.01BC 32/64-Bit Timer 0B 112 96 0x0000.01C0 32/64-Bit Timer 1A 113 97 0x0000.01C4 32/64-Bit Timer 1B 114 98 0x0000.01C8 32/64-Bit Timer 2A 115 99 0x0000.01CC 32/64-Bit Timer 2B 116 100 0x0000.01D0 32/64-Bit Timer 3A 117 101 0x0000.01D4 32/64-Bit Timer 3B 118 102 0x0000.01D8 32/64-Bit Timer 4A 119 103 0x0000.01DC 32/64-Bit Timer 4B 120 104 0x0000.01E0 32/64-Bit Timer 5A 121 105 0x0000.01E4 32/64-Bit Timer 5B 122 106 0x0000.01E8 System Exception (imprecise) 123-124 107-108 - 125 109 0x0000.01F4 I2C4 126 110 0x0000.01F8 I2C5 127 111 0x0000.01FC GPIO Port M 128 112 0x0000.0200 GPIO Port N 129-131 113-115 - 132 116 0x0000.0210 GPIO Port P (Summary or P0) 133 117 0x0000.0214 GPIO Port P1 134 118 0x0000.0218 GPIO Port P2 135 119 0x0000.021C GPIO Port P3 136 120 0x0000.0220 GPIO Port P4 137 121 0x0000.0224 GPIO Port P5 138 122 0x0000.0228 GPIO Port P6 139 123 0x0000.022C GPIO Port P7 140 124 0x0000.0230 GPIO Port Q (Summary or Q0) Reserved Reserved 106 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 2-9. Interrupts (continued) 2.5.3 Vector Number Interrupt Number (Bit in Interrupt Registers) Vector Address or Offset Description 141 125 0x0000.0234 GPIO Port Q1 142 126 0x0000.0238 GPIO Port Q2 143 127 0x0000.023C GPIO Port Q3 144 128 0x0000.0240 GPIO Port Q4 145 129 0x0000.0244 GPIO Port Q5 146 130 0x0000.0248 GPIO Port Q6 GPIO Port Q7 147 131 0x0000.024C 148-149 132-133 - 150 134 0x0000.0258 PWM1 Generator 0 151 135 0x0000.025C PWM1 Generator 1 152 136 0x0000.0260 PWM1 Generator 2 153 137 0x0000.0264 PWM1 Generator 3 154 138 0x0000.0268 PWM1 Fault Reserved Exception Handlers The processor handles exceptions using: ■ Interrupt Service Routines (ISRs). Interrupts (IRQx) are the exceptions handled by ISRs. ■ Fault Handlers. Hard fault, memory management fault, usage fault, and bus fault are fault exceptions handled by the fault handlers. ■ System Handlers. NMI, PendSV, SVCall, SysTick, and the fault exceptions are all system exceptions that are handled by system handlers. 2.5.4 Vector Table The vector table contains the reset value of the stack pointer and the start addresses, also called exception vectors, for all exception handlers. The vector table is constructed using the vector address or offset shown in Table 2-8 on page 103. Figure 2-6 on page 108 shows the order of the exception vectors in the vector table. The least-significant bit of each vector must be 1, indicating that the exception handler is Thumb code November 08, 2011 107 Texas Instruments-Advance Information The Cortex-M4F Processor Figure 2-6. Vector Table Exception number IRQ number 147 131 0x0254 . . . 0x004C . . . 18 2 17 1 16 0 15 -1 14 -2 Offset 0x0048 0x0044 0x0040 0x003C 0x0038 13 12 11 Vector IRQ131 . . . IRQ2 IRQ1 IRQ0 Systick PendSV Reserved Reserved for Debug -5 0x002C 10 9 SVCall Reserved 8 7 6 -10 5 -11 4 -12 3 -13 2 -14 0x0018 0x0014 0x0010 0x000C 0x0008 1 0x0004 0x0000 Usage fault Bus fault Memory management fault Hard fault NMI Reset Initial SP value On system reset, the vector table is fixed at address 0x0000.0000. Privileged software can write to the Vector Table Offset (VTABLE) register to relocate the vector table start address to a different memory location, in the range 0x0000.0400 to 0x3FFF.FC00 (see “Vector Table” on page 107). Note that when configuring the VTABLE register, the offset must be aligned on a 1024-byte boundary. 2.5.5 Exception Priorities As Table 2-8 on page 103 shows, all exceptions have an associated priority, with a lower priority value indicating a higher priority and configurable priorities for all exceptions except Reset, Hard fault, and NMI. If software does not configure any priorities, then all exceptions with a configurable priority have a priority of 0. For information about configuring exception priorities, see page 172 and page 154. Note: Configurable priority values for the Stellaris implementation are in the range 0-7. This means that the Reset, Hard fault, and NMI exceptions, with fixed negative priority values, always have higher priority than any other exception. For example, assigning a higher priority value to IRQ[0] and a lower priority value to IRQ[1] means that IRQ[1] has higher priority than IRQ[0]. If both IRQ[1] and IRQ[0] are asserted, IRQ[1] is processed before IRQ[0]. 108 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller If multiple pending exceptions have the same priority, the pending exception with the lowest exception number takes precedence. For example, if both IRQ[0] and IRQ[1] are pending and have the same priority, then IRQ[0] is processed before IRQ[1]. When the processor is executing an exception handler, the exception handler is preempted if a higher priority exception occurs. If an exception occurs with the same priority as the exception being handled, the handler is not preempted, irrespective of the exception number. However, the status of the new interrupt changes to pending. 2.5.6 Interrupt Priority Grouping To increase priority control in systems with interrupts, the NVIC supports priority grouping. This grouping divides each interrupt priority register entry into two fields: ■ An upper field that defines the group priority ■ A lower field that defines a subpriority within the group Only the group priority determines preemption of interrupt exceptions. When the processor is executing an interrupt exception handler, another interrupt with the same group priority as the interrupt being handled does not preempt the handler. If multiple pending interrupts have the same group priority, the subpriority field determines the order in which they are processed. If multiple pending interrupts have the same group priority and subpriority, the interrupt with the lowest IRQ number is processed first. For information about splitting the interrupt priority fields into group priority and subpriority, see page 166. 2.5.7 Exception Entry and Return Descriptions of exception handling use the following terms: ■ Preemption. When the processor is executing an exception handler, an exception can preempt the exception handler if its priority is higher than the priority of the exception being handled. See “Interrupt Priority Grouping” on page 109 for more information about preemption by an interrupt. When one exception preempts another, the exceptions are called nested exceptions. See “Exception Entry” on page 110 more information. ■ Return. Return occurs when the exception handler is completed, and there is no pending exception with sufficient priority to be serviced and the completed exception handler was not handling a late-arriving exception. The processor pops the stack and restores the processor state to the state it had before the interrupt occurred. See “Exception Return” on page 111 for more information. ■ Tail-Chaining. This mechanism speeds up exception servicing. On completion of an exception handler, if there is a pending exception that meets the requirements for exception entry, the stack pop is skipped and control transfers to the new exception handler. ■ Late-Arriving. This mechanism speeds up preemption. If a higher priority exception occurs during state saving for a previous exception, the processor switches to handle the higher priority exception and initiates the vector fetch for that exception. State saving is not affected by late arrival because the state saved is the same for both exceptions. Therefore, the state saving continues uninterrupted. The processor can accept a late arriving exception until the first instruction of the exception handler of the original exception enters the execute stage of the processor. On November 08, 2011 109 Texas Instruments-Advance Information The Cortex-M4F Processor return from the exception handler of the late-arriving exception, the normal tail-chaining rules apply. 2.5.7.1 Exception Entry Exception entry occurs when there is a pending exception with sufficient priority and either the processor is in Thread mode or the new exception is of higher priority than the exception being handled, in which case the new exception preempts the original exception. When one exception preempts another, the exceptions are nested. Sufficient priority means the exception has more priority than any limits set by the mask registers (see PRIMASK on page 85, FAULTMASK on page 86, and BASEPRI on page 87). An exception with less priority than this is pending but is not handled by the processor. When the processor takes an exception, unless the exception is a tail-chained or a late-arriving exception, the processor pushes information onto the current stack. This operation is referred to as stacking and the structure of eight data words is referred to as stack frame. When using floating-point routines, the Cortex-M4F processor automatically stacks the architected floating-point state on exception entry. Figure 2-7 on page 111 shows the Cortex-M4F stack frame layout when floating-point state is preserved on the stack as the result of an interrupt or an exception. Note: Where stack space for floating-point state is not allocated, the stack frame is the same as that of ARMv7-M implementations without an FPU. Figure 2-7 on page 111 shows this stack frame also. 110 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 2-7. Exception Stack Frame ... {aligner} FPSCR S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0 xPSR PC LR R12 R3 R2 R1 R0 Exception frame with floating-point storage Pre-IRQ top of stack Decreasing memory address IRQ top of stack ... {aligner} xPSR PC LR R12 R3 R2 R1 R0 Pre-IRQ top of stack IRQ top of stack Exception frame without floating-point storage Immediately after stacking, the stack pointer indicates the lowest address in the stack frame. The stack frame includes the return address, which is the address of the next instruction in the interrupted program. This value is restored to the PC at exception return so that the interrupted program resumes. In parallel to the stacking operation, the processor performs a vector fetch that reads the exception handler start address from the vector table. When stacking is complete, the processor starts executing the exception handler. At the same time, the processor writes an EXC_RETURN value to the LR, indicating which stack pointer corresponds to the stack frame and what operation mode the processor was in before the entry occurred. If no higher-priority exception occurs during exception entry, the processor starts executing the exception handler and automatically changes the status of the corresponding pending interrupt to active. If another higher-priority exception occurs during exception entry, known as late arrival, the processor starts executing the exception handler for this exception and does not change the pending status of the earlier exception. 2.5.7.2 Exception Return Exception return occurs when the processor is in Handler mode and executes one of the following instructions to load the EXC_RETURN value into the PC: November 08, 2011 111 Texas Instruments-Advance Information The Cortex-M4F Processor ■ An LDM or POP instruction that loads the PC ■ A BX instruction using any register ■ An LDR instruction with the PC as the destination EXC_RETURN is the value loaded into the LR on exception entry. The exception mechanism relies on this value to detect when the processor has completed an exception handler. The lowest five bits of this value provide information on the return stack and processor mode. Table 2-10 on page 112 shows the EXC_RETURN values with a description of the exception return behavior. EXC_RETURN bits 31:5 are all set. When this value is loaded into the PC, it indicates to the processor that the exception is complete, and the processor initiates the appropriate exception return sequence. Table 2-10. Exception Return Behavior EXC_RETURN[31:0] Description 0xFFFF.FFE0 Reserved 0xFFFF.FFE1 Return to Handler mode. Exception return uses floating-point state from MSP. Execution uses MSP after return. 0xFFFF.FFE2 - 0xFFFF.FFE8 Reserved 0xFFFF.FFE9 Return to Thread mode. Exception return uses floating-point state from MSP. Execution uses MSP after return. 0xFFFF.FFEA - 0xFFFF.FFEC Reserved 0xFFFF.FFED Return to Thread mode. Exception return uses floating-point state from PSP. Execution uses PSP after return. 0xFFFF.FFEE - 0xFFFF.FFF0 Reserved 0xFFFF.FFF1 Return to Handler mode. Exception return uses non-floating-point state from MSP. Execution uses MSP after return. 0xFFFF.FFF2 - 0xFFFF.FFF8 Reserved 0xFFFF.FFF9 Return to Thread mode. Exception return uses non-floating-point state from MSP. Execution uses MSP after return. 0xFFFF.FFFA - 0xFFFF.FFFC Reserved 0xFFFF.FFFD Return to Thread mode. Exception return uses non-floating-point state from PSP. Execution uses PSP after return. 0xFFFF.FFFE - 0xFFFF.FFFF 2.6 Reserved Fault Handling Faults are a subset of the exceptions (see “Exception Model” on page 101). The following conditions generate a fault: ■ A bus error on an instruction fetch or vector table load or a data access. 112 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ An internally detected error such as an undefined instruction or an attempt to change state with a BX instruction. ■ Attempting to execute an instruction from a memory region marked as Non-Executable (XN). ■ An MPU fault because of a privilege violation or an attempt to access an unmanaged region. 2.6.1 Fault Types Table 2-11 on page 113 shows the types of fault, the handler used for the fault, the corresponding fault status register, and the register bit that indicates the fault has occurred. See page 179 for more information about the fault status registers. Table 2-11. Faults Fault Handler Fault Status Register Bit Name Bus error on a vector read Hard fault Hard Fault Status (HFAULTSTAT) VECT Fault escalated to a hard fault Hard fault Hard Fault Status (HFAULTSTAT) FORCED MPU or default memory mismatch on instruction access Memory management fault Memory Management Fault Status (MFAULTSTAT) IERR MPU or default memory mismatch on data access Memory management fault Memory Management Fault Status (MFAULTSTAT) DERR MPU or default memory mismatch on exception stacking Memory management fault Memory Management Fault Status (MFAULTSTAT) MSTKE MPU or default memory mismatch on exception unstacking Memory management fault Memory Management Fault Status (MFAULTSTAT) MUSTKE MPU or default memory mismatch during lazy floating-point state preservation Memory management fault Memory Management Fault Status (MFAULTSTAT) MLSPERR Bus error during exception stacking Bus fault Bus Fault Status (BFAULTSTAT) BSTKE Bus error during exception unstacking Bus fault Bus Fault Status (BFAULTSTAT) BUSTKE Bus error during instruction prefetch Bus fault Bus Fault Status (BFAULTSTAT) IBUS Bus error during lazy floating-point state Bus fault preservation Bus Fault Status (BFAULTSTAT) BLSPE Precise data bus error Bus fault Bus Fault Status (BFAULTSTAT) PRECISE Imprecise data bus error Bus fault Bus Fault Status (BFAULTSTAT) IMPRE Attempt to access a coprocessor Usage fault Usage Fault Status (UFAULTSTAT) NOCP Undefined instruction Usage fault Usage Fault Status (UFAULTSTAT) UNDEF Attempt to enter an invalid instruction b set state Usage fault Usage Fault Status (UFAULTSTAT) INVSTAT Invalid EXC_RETURN value Usage fault Usage Fault Status (UFAULTSTAT) INVPC Illegal unaligned load or store Usage fault Usage Fault Status (UFAULTSTAT) UNALIGN Divide by 0 Usage fault Usage Fault Status (UFAULTSTAT) DIV0 a a. Occurs on an access to an XN region even if the MPU is disabled. b. Attempting to use an instruction set other than the Thumb instruction set, or returning to a non load-store-multiple instruction with ICI continuation. 2.6.2 Fault Escalation and Hard Faults All fault exceptions except for hard fault have configurable exception priority (see SYSPRI1 on page 172). Software can disable execution of the handlers for these faults (see SYSHNDCTRL on page 175). November 08, 2011 113 Texas Instruments-Advance Information The Cortex-M4F Processor Usually, the exception priority, together with the values of the exception mask registers, determines whether the processor enters the fault handler, and whether a fault handler can preempt another fault handler as described in “Exception Model” on page 101. In some situations, a fault with configurable priority is treated as a hard fault. This process is called priority escalation, and the fault is described as escalated to hard fault. Escalation to hard fault occurs when: ■ A fault handler causes the same kind of fault as the one it is servicing. This escalation to hard fault occurs because a fault handler cannot preempt itself because it must have the same priority as the current priority level. ■ A fault handler causes a fault with the same or lower priority as the fault it is servicing. This situation happens because the handler for the new fault cannot preempt the currently executing fault handler. ■ An exception handler causes a fault for which the priority is the same as or lower than the currently executing exception. ■ A fault occurs and the handler for that fault is not enabled. If a bus fault occurs during a stack push when entering a bus fault handler, the bus fault does not escalate to a hard fault. Thus if a corrupted stack causes a fault, the fault handler executes even though the stack push for the handler failed. The fault handler operates but the stack contents are corrupted. Note: 2.6.3 Only Reset and NMI can preempt the fixed priority hard fault. A hard fault can preempt any exception other than Reset, NMI, or another hard fault. Fault Status Registers and Fault Address Registers The fault status registers indicate the cause of a fault. For bus faults and memory management faults, the fault address register indicates the address accessed by the operation that caused the fault, as shown in Table 2-12 on page 114. Table 2-12. Fault Status and Fault Address Registers Handler Status Register Name Address Register Name Register Description Hard fault Hard Fault Status (HFAULTSTAT) - page 185 Memory management Memory Management Fault Status fault (MFAULTSTAT) Memory Management Fault Address (MMADDR) page 179 Bus fault Bus Fault Address (FAULTADDR) page 179 - page 179 Bus Fault Status (BFAULTSTAT) Usage fault 2.6.4 Usage Fault Status (UFAULTSTAT) page 186 page 187 Lockup The processor enters a lockup state if a hard fault occurs when executing the NMI or hard fault handlers. When the processor is in the lockup state, it does not execute any instructions. The processor remains in lockup state until it is reset, an NMI occurs, or it is halted by a debugger. Note: If the lockup state occurs from the NMI handler, a subsequent NMI does not cause the processor to leave the lockup state. 114 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 2.7 Power Management The Cortex-M4F processor sleep modes reduce power consumption: ■ Sleep mode stops the processor clock. ■ Deep-sleep mode stops the system clock and switches off the PLL and Flash memory. The SLEEPDEEP bit of the System Control (SYSCTRL) register selects which sleep mode is used (see page 168). For more information about the behavior of the sleep modes, see “System Control” on page 228. This section describes the mechanisms for entering sleep mode and the conditions for waking up from sleep mode, both of which apply to Sleep mode and Deep-sleep mode. 2.7.1 Entering Sleep Modes This section describes the mechanisms software can use to put the processor into one of the sleep modes. The system can generate spurious wake-up events, for example a debug operation wakes up the processor. Therefore, software must be able to put the processor back into sleep mode after such an event. A program might have an idle loop to put the processor back to sleep mode. 2.7.1.1 Wait for Interrupt The wait for interrupt instruction, WFI, causes immediate entry to sleep mode unless the wake-up condition is true (see “Wake Up from WFI or Sleep-on-Exit” on page 116). When the processor executes a WFI instruction, it stops executing instructions and enters sleep mode. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. 2.7.1.2 Wait for Event The wait for event instruction, WFE, causes entry to sleep mode conditional on the value of a one-bit event register. When the processor executes a WFE instruction, it checks the event register. If the register is 0, the processor stops executing instructions and enters sleep mode. If the register is 1, the processor clears the register and continues executing instructions without entering sleep mode. If the event register is 1, the processor must not enter sleep mode on execution of a WFE instruction. Typically, this situation occurs if an SEV instruction has been executed. Software cannot access this register directly. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. 2.7.1.3 Sleep-on-Exit If the SLEEPEXIT bit of the SYSCTRL register is set, when the processor completes the execution of all exception handlers, it returns to Thread mode and immediately enters sleep mode. This mechanism can be used in applications that only require the processor to run when an exception occurs. 2.7.2 Wake Up from Sleep Mode The conditions for the processor to wake up depend on the mechanism that cause it to enter sleep mode. November 08, 2011 115 Texas Instruments-Advance Information The Cortex-M4F Processor 2.7.2.1 Wake Up from WFI or Sleep-on-Exit Normally, the processor wakes up only when the NVIC detects an exception with sufficient priority to cause exception entry. Some embedded systems might have to execute system restore tasks after the processor wakes up and before executing an interrupt handler. Entry to the interrupt handler can be delayed by setting the PRIMASK bit and clearing the FAULTMASK bit. If an interrupt arrives that is enabled and has a higher priority than current exception priority, the processor wakes up but does not execute the interrupt handler until the processor clears PRIMASK. For more information about PRIMASK and FAULTMASK, see page 85 and page 86. 2.7.2.2 Wake Up from WFE The processor wakes up if it detects an exception with sufficient priority to cause exception entry. In addition, if the SEVONPEND bit in the SYSCTRL register is set, any new pending interrupt triggers an event and wakes up the processor, even if the interrupt is disabled or has insufficient priority to cause exception entry. For more information about SYSCTRL, see page 168. 2.7.3 The Wake-Up Interrupt Controller The Wake-Up Interrupt Controller (WIC) is a peripheral that can detect an interrupt and wake the processor from deep sleep mode. The WIC is enabled only when the DEEPSLEEP bit in the SCR register is set (see page 168). The WIC is not programmable, and does not have any registers or user interface. It operates entirely from hardware signals. When the WIC is enabled and the processor enters deep sleep mode, the power management unit in the system can power down most of the Cortex-M4F processor. This has the side effect of stopping the SysTick timer. When the WIC receives an interrupt, it takes a number of clock cycles to wake up the processor and restore its state, before it can process the interrupt. This means interrupt latency is increased in deep sleep mode. Note: 2.8 If the processor detects a connection to a debugger it disables the WIC. Instruction Set Summary The processor implements a version of the Thumb instruction set. Table 2-13 on page 116 lists the supported instructions. Note: In Table 2-13 on page 116: ■ ■ ■ ■ ■ Angle brackets, , enclose alternative forms of the operand Braces, {}, enclose optional operands The Operands column is not exhaustive Op2 is a flexible second operand that can be either a register or a constant Most instructions can use an optional condition code suffix For more information on the instructions and operands, see the instruction descriptions in the ARM® Cortex™-M4 Technical Reference Manual. Table 2-13. Cortex-M4F Instruction Summary Mnemonic Operands Brief Description Flags ADC, ADCS {Rd,} Rn, Op2 Add with carry N,Z,C,V ADD, ADDS {Rd,} Rn, Op2 Add N,Z,C,V ADD, ADDW {Rd,} Rn , #imm12 Add - 116 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 2-13. Cortex-M4F Instruction Summary (continued) Mnemonic Operands Brief Description Flags ADR Rd, label Load PC-relative address - AND, ANDS {Rd,} Rn, Op2 Logical AND N,Z,C ASR, ASRS Rd, Rm, Arithmetic shift right N,Z,C B label Branch - BFC Rd, #lsb, #width Bit field clear - BFI Rd, Rn, #lsb, #width Bit field insert - BIC, BICS {Rd,} Rn, Op2 Bit clear N,Z,C BKPT #imm Breakpoint - BL label Branch with link - BLX Rm Branch indirect with link - BX Rm Branch indirect - CBNZ Rn, label Compare and branch if non-zero - CBZ Rn, label Compare and branch if zero - CLREX - Clear exclusive - CLZ Rd, Rm Count leading zeros - CMN Rn, Op2 Compare negative N,Z,C,V CMP Rn, Op2 Compare N,Z,C,V CPSID i Change processor state, disable interrupts - CPSIE i Change processor state, enable interrupts - DMB - Data memory barrier - DSB - Data synchronization barrier - EOR, EORS {Rd,} Rn, Op2 Exclusive OR N,Z,C ISB - Instruction synchronization barrier - IT - If-Then condition block - LDM Rn{!}, reglist Load multiple registers, increment after - LDMDB, LDMEA Rn{!}, reglist Load multiple registers, decrement before LDMFD, LDMIA Rn{!}, reglist Load multiple registers, increment after - LDR Rt, [Rn, #offset] Load register with word - LDRB, LDRBT Rt, [Rn, #offset] Load register with byte - LDRD Rt, Rt2, [Rn, #offset] Load register with two bytes - LDREX Rt, [Rn, #offset] Load register exclusive - LDREXB Rt, [Rn] Load register exclusive with byte - LDREXH Rt, [Rn] Load register exclusive with halfword - LDRH, LDRHT Rt, [Rn, #offset] Load register with halfword - LDRSB, LDRSBT Rt, [Rn, #offset] Load register with signed byte - LDRSH, LDRSHT Rt, [Rn, #offset] Load register with signed halfword - LDRT Rt, [Rn, #offset] Load register with word - LSL, LSLS Rd, Rm, Logical shift left N,Z,C LSR, LSRS Rd, Rm, Logical shift right N,Z,C November 08, 2011 - 117 Texas Instruments-Advance Information The Cortex-M4F Processor Table 2-13. Cortex-M4F Instruction Summary (continued) Mnemonic Operands Brief Description Flags MLA Rd, Rn, Rm, Ra Multiply with accumulate, 32-bit result - MLS Rd, Rn, Rm, Ra Multiply and subtract, 32-bit result - MOV, MOVS Rd, Op2 Move N,Z,C MOV, MOVW Rd, #imm16 Move 16-bit constant N,Z,C MOVT Rd, #imm16 Move top - MRS Rd, spec_reg Move from special register to general register - MSR spec_reg, Rm Move from general register to special register N,Z,C,V MUL, MULS {Rd,} Rn, Rm Multiply, 32-bit result N,Z MVN, MVNS Rd, Op2 Move NOT N,Z,C NOP - No operation - ORN, ORNS {Rd,} Rn, Op2 Logical OR NOT N,Z,C ORR, ORRS {Rd,} Rn, Op2 Logical OR N,Z,C PKHTB, PKHBT {Rd,} Rn, Rm, Op2 Pack halfword - POP reglist Pop registers from stack - PUSH reglist Push registers onto stack - QADD {Rd,} Rn, Rm Saturating add Q QADD16 {Rd,} Rn, Rm Saturating add 16 - QADD8 {Rd,} Rn, Rm Saturating add 8 - QASX {Rd,} Rn, Rm Saturating add and subtract with exchange - QDADD {Rd,} Rn, Rm Saturating double and add Q QDSUB {Rd,} Rn, Rm Saturating double and subtract Q QSAX {Rd,} Rn, Rm Saturating subtract and add with exchange - QSUB {Rd,} Rn, Rm Saturating subtract Q QSUB16 {Rd,} Rn, Rm Saturating subtract 16 - QSUB8 {Rd,} Rn, Rm Saturating subtract 8 - RBIT Rd, Rn Reverse bits - REV Rd, Rn Reverse byte order in a word - REV16 Rd, Rn Reverse byte order in each halfword - REVSH Rd, Rn Reverse byte order in bottom halfword and sign extend - ROR, RORS Rd, Rm, Rotate right N,Z,C RRX, RRXS Rd, Rm Rotate right with extend N,Z,C RSB, RSBS {Rd,} Rn, Op2 Reverse subtract N,Z,C,V SADD16 {Rd,} Rn, Rm Signed add 16 GE SADD8 {Rd,} Rn, Rm Signed add 8 GE SASX {Rd,} Rn, Rm Signed add and subtract with exchange GE SBC, SBCS {Rd,} Rn, Op2 Subtract with carry N,Z,C,V SBFX Rd, Rn, #lsb, #width Signed bit field extract - SDIV {Rd,} Rn, Rm Signed divide - 118 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 2-13. Cortex-M4F Instruction Summary (continued) Mnemonic Operands Brief Description Flags SEL {Rd,} Rn, Rm Select bytes - SEV - Send event - SHADD16 {Rd,} Rn, Rm Signed halving add 16 - SHADD8 {Rd,} Rn, Rm Signed halving add 8 - SHASX {Rd,} Rn, Rm Signed halving add and subtract with exchange - SHSAX {Rd,} Rn, Rm Signed halving add and subtract with exchange - SHSUB16 {Rd,} Rn, Rm Signed halving subtract 16 - SHSUB8 {Rd,} Rn, Rm Signed halving subtract 8 - SMLABB, Rd, Rn, Rm, Ra Signed multiply accumulate long (halfwords) Q Rd, Rn, Rm, Ra Signed multiply accumulate dual Q SMLAL RdLo, RdHi, Rn, Rm Signed multiply with accumulate (32x32+64), 64-bit result - SMLALBB, RdLo, RdHi, Rn, Rm Signed multiply accumulate long (halfwords) - SMLALD, SMLALDX RdLo, RdHi, Rn, Rm Signed multiply accumulate long dual - SMLAWB,SMLAWT Rd, Rn, Rm, Ra Signed multiply accumulate, word by halfword Q SMLSD Rd, Rn, Rm, Ra Signed multiply subtract dual Q RdLo, RdHi, Rn, Rm Signed multiply subtract long dual SMMLA Rd, Rn, Rm, Ra Signed most significant word multiply accumulate - SMMLS, Rd, Rn, Rm, Ra Signed most significant word multiply subtract - {Rd,} Rn, Rm Signed most significant word multiply - {Rd,} Rn, Rm Signed dual multiply add Q {Rd,} Rn, Rm Signed multiply halfwords - SMULL RdLo, RdHi, Rn, Rm Signed multiply (32x32), 64-bit result - SMULWB, {Rd,} Rn, Rm Signed multiply by halfword - SMLABT, SMLATB, SMLATT SMLAD, SMLADX SMLALBT, SMLALTB, SMLALTT SMLSDX SMLSLD SMLSLDX SMMLR SMMUL, SMMULR SMUAD SMUADX SMULBB, SMULBT, SMULTB, SMULTT SMULWT November 08, 2011 119 Texas Instruments-Advance Information The Cortex-M4F Processor Table 2-13. Cortex-M4F Instruction Summary (continued) Mnemonic Operands Brief Description Flags SMUSD, {Rd,} Rn, Rm Signed dual multiply subtract - SSAT Rd, #n, Rm {,shift #s} Signed saturate Q SSAT16 Rd, #n, Rm Signed saturate 16 Q SSAX {Rd,} Rn, Rm Saturating subtract and add with exchange GE SSUB16 {Rd,} Rn, Rm Signed subtract 16 - SSUB8 {Rd,} Rn, Rm Signed subtract 8 - STM Rn{!}, reglist Store multiple registers, increment after - STMDB, STMEA Rn{!}, reglist Store multiple registers, decrement before STMFD, STMIA Rn{!}, reglist Store multiple registers, increment after - STR Rt, [Rn {, #offset}] Store register word - STRB, STRBT Rt, [Rn {, #offset}] Store register byte - STRD Rt, Rt2, [Rn {, #offset}] Store register two words - STREX Rt, Rt, [Rn {, #offset}] Store register exclusive - STREXB Rd, Rt, [Rn] Store register exclusive byte - STREXH Rd, Rt, [Rn] Store register exclusive halfword - STRH, STRHT Rt, [Rn {, #offset}] Store register halfword - STRSB, STRSBT Rt, [Rn {, #offset}] Store register signed byte - STRSH, STRSHT Rt, [Rn {, #offset}] Store register signed halfword - STRT Rt, [Rn {, #offset}] Store register word - SUB, SUBS {Rd,} Rn, Op2 Subtract N,Z,C,V SUB, SUBW {Rd,} Rn, #imm12 Subtract 12-bit constant N,Z,C,V SVC #imm Supervisor call - SXTAB {Rd,} Rn, Rm, {,ROR #} Extend 8 bits to 32 and add - SXTAB16 {Rd,} Rn, Rm,{,ROR #} Dual extend 8 bits to 16 and add - SXTAH {Rd,} Rn, Rm,{,ROR #} Extend 16 bits to 32 and add - SXTB16 {Rd,} Rm {,ROR #n} Signed extend byte 16 - SXTB {Rd,} Rm {,ROR #n} Sign extend a byte - SXTH {Rd,} Rm {,ROR #n} Sign extend a halfword - TBB [Rn, Rm] Table branch byte - TBH [Rn, Rm, LSL #1] Table branch halfword - TEQ Rn, Op2 Test equivalence N,Z,C TST Rn, Op2 Test N,Z,C UADD16 {Rd,} Rn, Rm Unsigned add 16 GE UADD8 {Rd,} Rn, Rm Unsigned add 8 GE UASX {Rd,} Rn, Rm Unsigned add and subtract with exchange GE UHADD16 {Rd,} Rn, Rm Unsigned halving add 16 - UHADD8 {Rd,} Rn, Rm Unsigned halving add 8 - UHASX {Rd,} Rn, Rm Unsigned halving add and subtract with exchange SMUSDX 120 - November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 2-13. Cortex-M4F Instruction Summary (continued) Mnemonic Operands Brief Description UHSAX {Rd,} Rn, Rm Unsigned halving subtract and add with exchange UHSUB16 {Rd,} Rn, Rm Unsigned halving subtract 16 - UHSUB8 {Rd,} Rn, Rm Unsigned halving subtract 8 - UBFX Rd, Rn, #lsb, #width Unsigned bit field extract - UDIV {Rd,} Rn, Rm Unsigned divide - UMAAL RdLo, RdHi, Rn, Rm Unsigned multiply accumulate accumulate long (32x32+64), 64-bit result - UMLAL RdLo, RdHi, Rn, Rm Unsigned multiply with accumulate (32x32+32+32), 64-bit result - UMULL RdLo, RdHi, Rn, Rm Unsigned multiply (32x 2), 64-bit result - UQADD16 {Rd,} Rn, Rm Unsigned Saturating Add 16 - UQADD8 {Rd,} Rn, Rm Unsigned Saturating Add 8 - UQASX {Rd,} Rn, Rm Unsigned Saturating Add and Subtract with Exchange UQSAX {Rd,} Rn, Rm Unsigned Saturating Subtract and Add with Exchange UQSUB16 {Rd,} Rn, Rm Unsigned Saturating Subtract 16 - UQSUB8 {Rd,} Rn, Rm Unsigned Saturating Subtract 8 - USAD8 {Rd,} Rn, Rm Unsigned Sum of Absolute Differences - USADA8 {Rd,} Rn, Rm, Ra Unsigned Sum of Absolute Differences and Accumulate USAT Rd, #n, Rm {,shift #s} Unsigned Saturate Q USAT16 Rd, #n, Rm Unsigned Saturate 16 Q USAX {Rd,} Rn, Rm Unsigned Subtract and add with Exchange GE USUB16 {Rd,} Rn, Rm Unsigned Subtract 16 GE USUB8 {Rd,} Rn, Rm Unsigned Subtract 8 GE UXTAB {Rd,} Rn, Rm, {,ROR #} Rotate, extend 8 bits to 32 and Add - UXTAB16 {Rd,} Rn, Rm, {,ROR #} Rotate, dual extend 8 bits to 16 and Add - UXTAH {Rd,} Rn, Rm, {,ROR #} Rotate, unsigned extend and Add Halfword - UXTB {Rd,} Rm, {,ROR #n} Zero extend a Byte - UXTB16 {Rd,} Rm, {,ROR #n} Unsigned Extend Byte 16 - UXTH {Rd,} Rm, {,ROR #n} Zero extend a Halfword - VABS.F32 Sd, Sm Floating-point Absolute - VADD.F32 {Sd,} Sn, Sm Floating-point Add - VCMP.F32 Sd, Compare two floating-point registers, or FPSCR one floating-point register and zero VCMPE.F32 Sd, Compare two floating-point registers, or FPSCR one floating-point register and zero with Invalid Operation check VCVT.S32.F32 Sd, Sm Convert between floating-point and integer November 08, 2011 Flags - 121 Texas Instruments-Advance Information The Cortex-M4F Processor Table 2-13. Cortex-M4F Instruction Summary (continued) Mnemonic Operands Brief Description VCVT.S16.F32 Sd, Sd, #fbits Convert between floating-point and fixed point VCVTR.S32.F32 Sd, Sm Convert between floating-point and integer with rounding - VCVT.F32.F16 Sd, Sm Converts half-precision value to single-precision - VCVTT.F32.F16 Sd, Sm Converts single-precision register to half-precision - VDIV.F32 {Sd,} Sn, Sm Floating-point Divide - VFMA.F32 {Sd,} Sn, Sm Floating-point Fused Multiply Accumulate - VFNMA.F32 {Sd,} Sn, Sm Floating-point Fused Negate Multiply Accumulate - VFMS.F32 {Sd,} Sn, Sm Floating-point Fused Multiply Subtract - VFNMS.F32 {Sd,} Sn, Sm Floating-point Fused Negate Multiply Subtract - VLDM.F Rn{!}, list Load Multiple extension registers - VLDR.F , [Rn] Load an extension register from memory - VLMA.F32 {Sd,} Sn, Sm Floating-point Multiply Accumulate - VLMS.F32 {Sd,} Sn, Sm Floating-point Multiply Subtract - VMOV.F32 Sd, #imm Floating-point Move immediate - VMOV Sd, Sm Floating-point Move register - VMOV Sn, Rt Copy ARM core register to single precision - VMOV Sm, Sm1, Rt, Rt2 Copy 2 ARM core registers to 2 single precision - VMOV Dd[x], Rt Copy ARM core register to scalar - VMOV Rt, Dn[x] Copy scalar to ARM core register - VMRS Rt, FPSCR Move FPSCR to ARM core register or APSR N,Z,C,V VMSR FPSCR, Rt Move to FPSCR from ARM Core register FPSCR VMUL.F32 {Sd,} Sn, Sm Floating-point Multiply - VNEG.F32 Sd, Sm Floating-point Negate - VNMLA.F32 {Sd,} Sn, Sm Floating-point Multiply and Add - VNMLS.F32 {Sd,} Sn, Sm Floating-point Multiply and Subtract - VNMUL {Sd,} Sn, Sm Floating-point Multiply - VPOP list Pop extension registers - VPUSH list Push extension registers - VSQRT.F32 Sd, Sm Calculates floating-point Square Root - VSTM Rn{!}, list Floating-point register Store Multiple - VSTR.F3 Sd, [Rn] Stores an extension register to memory - VSUB.F {Sd,} Sn, Sm Floating-point Subtract - USAT Rd, #n, Rm {,shift #s} Unsigned saturate Q UXTB {Rd,} Rm {,ROR #n} Zero extend a byte - UXTH {Rd,} Rm {,ROR #n} Zero extend a halfword - 122 Flags November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 2-13. Cortex-M4F Instruction Summary (continued) Mnemonic Operands Brief Description Flags WFE - Wait for event - WFI - Wait for interrupt - November 08, 2011 123 Texas Instruments-Advance Information Cortex-M4 Peripherals 3 Cortex-M4 Peripherals ® This chapter provides information on the Stellaris implementation of the Cortex-M4 processor peripherals, including: ■ SysTick (see page 125) Provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. ■ Nested Vectored Interrupt Controller (NVIC) (see page 126) – Facilitates low-latency exception and interrupt handling – Controls power management – Implements system control registers ■ System Control Block (SCB) (see page 127) Provides system implementation information and system control, including configuration, control, and reporting of system exceptions. ■ Memory Protection Unit (MPU) (see page 127) Supports the standard ARMv7 Protected Memory System Architecture (PMSA) model. The MPU provides full support for protection regions, overlapping protection regions, access permissions, and exporting memory attributes to the system. ■ Floating-Point Unit (FPU) (see page 132) Fully supports single-precision add, subtract, multiply, divide, multiply and accumulate, and square root operations. It also provides conversions between fixed-point and floating-point data formats, and floating-point constant instructions. Table 3-1 on page 124 shows the address map of the Private Peripheral Bus (PPB). Some peripheral register regions are split into two address regions, as indicated by two addresses listed. Table 3-1. Core Peripheral Register Regions Address Core Peripheral Description (see page ...) 0xE000.E010-0xE000.E01F System Timer 125 0xE000.E100-0xE000.E4EF Nested Vectored Interrupt Controller 126 System Control Block 127 0xE000.ED90-0xE000.EDB8 Memory Protection Unit 127 0xE000.EF30-0xE000.EF44 Floating Point Unit 132 0xE000.EF00-0xE000.EF03 0xE000.E008-0xE000.E00F 0xE000.ED00-0xE000.ED3F 3.1 Functional Description This chapter provides information on the Stellaris implementation of the Cortex-M4 processor peripherals: SysTick, NVIC, SCB and MPU. 124 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 3.1.1 System Timer (SysTick) Cortex-M4 includes an integrated system timer, SysTick, which provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter can be used in several different ways, for example as: ■ An RTOS tick timer that fires at a programmable rate (for example, 100 Hz) and invokes a SysTick routine. ■ A high-speed alarm timer using the system clock. ■ A variable rate alarm or signal timer—the duration is range-dependent on the reference clock used and the dynamic range of the counter. ■ A simple counter used to measure time to completion and time used. ■ An internal clock source control based on missing/meeting durations. The COUNT bit in the STCTRL control and status register can be used to determine if an action completed within a set duration, as part of a dynamic clock management control loop. The timer consists of three registers: ■ SysTick Control and Status (STCTRL): A control and status counter to configure its clock, enable the counter, enable the SysTick interrupt, and determine counter status. ■ SysTick Reload Value (STRELOAD): The reload value for the counter, used to provide the counter's wrap value. ■ SysTick Current Value (STCURRENT): The current value of the counter. When enabled, the timer counts down on each clock from the reload value to zero, reloads (wraps) to the value in the STRELOAD register on the next clock edge, then decrements on subsequent clocks. Clearing the STRELOAD register disables the counter on the next wrap. When the counter reaches zero, the COUNT status bit is set. The COUNT bit clears on reads. Writing to the STCURRENT register clears the register and the COUNT status bit. The write does not trigger the SysTick exception logic. On a read, the current value is the value of the register at the time the register is accessed. The SysTick counter runs on either the system clock or the precision internal oscillator (PIOSC) divided by 4. If this clock signal is stopped for low power mode, the SysTick counter stops. SysTick can be kept running during Deep-sleep mode by setting the CLK_SRC bit in the SysTick Control and Status Register (STCTRL) register and ensuring that the PIOSCPD bit in the Deep Sleep Clock Configuration (DSLPCLKCFG) register is clear. Ensure software uses aligned word accesses to access the SysTick registers. The SysTick counter reload and current value are undefined at reset; the correct initialization sequence for the SysTick counter is: 1. Program the value in the STRELOAD register. 2. Clear the STCURRENT register by writing to it with any value. 3. Configure the STCTRL register for the required operation. Note: When the processor is halted for debugging, the counter does not decrement. November 08, 2011 125 Texas Instruments-Advance Information Cortex-M4 Peripherals 3.1.2 Nested Vectored Interrupt Controller (NVIC) This section describes the Nested Vectored Interrupt Controller (NVIC) and the registers it uses. The NVIC supports: ■ 104 interrupts. ■ A programmable priority level of 0-7 for each interrupt. A higher level corresponds to a lower priority, so level 0 is the highest interrupt priority. ■ Low-latency exception and interrupt handling. ■ Level and pulse detection of interrupt signals. ■ Dynamic reprioritization of interrupts. ■ Grouping of priority values into group priority and subpriority fields. ■ Interrupt tail-chaining. ■ An external Non-maskable interrupt (NMI). The processor automatically stacks its state on exception entry and unstacks this state on exception exit, with no instruction overhead, providing low latency exception handling. 3.1.2.1 Level-Sensitive and Pulse Interrupts The processor supports both level-sensitive and pulse interrupts. Pulse interrupts are also described as edge-triggered interrupts. A level-sensitive interrupt is held asserted until the peripheral deasserts the interrupt signal. Typically this happens because the ISR accesses the peripheral, causing it to clear the interrupt request. A pulse interrupt is an interrupt signal sampled synchronously on the rising edge of the processor clock. To ensure the NVIC detects the interrupt, the peripheral must assert the interrupt signal for at least one clock cycle, during which the NVIC detects the pulse and latches the interrupt. When the processor enters the ISR, it automatically removes the pending state from the interrupt (see “Hardware and Software Control of Interrupts” on page 126 for more information). For a level-sensitive interrupt, if the signal is not deasserted before the processor returns from the ISR, the interrupt becomes pending again, and the processor must execute its ISR again. As a result, the peripheral can hold the interrupt signal asserted until it no longer needs servicing. 3.1.2.2 Hardware and Software Control of Interrupts The Cortex-M4 latches all interrupts. A peripheral interrupt becomes pending for one of the following reasons: ■ The NVIC detects that the interrupt signal is High and the interrupt is not active. ■ The NVIC detects a rising edge on the interrupt signal. ■ Software writes to the corresponding interrupt set-pending register bit, or to the Software Trigger Interrupt (SWTRIG) register to make a Software-Generated Interrupt pending. See the INT bit in the PEND0 register on page 148 or SWTRIG on page 158. A pending interrupt remains pending until one of the following: 126 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ The processor enters the ISR for the interrupt, changing the state of the interrupt from pending to active. Then: – For a level-sensitive interrupt, when the processor returns from the ISR, the NVIC samples the interrupt signal. If the signal is asserted, the state of the interrupt changes to pending, which might cause the processor to immediately re-enter the ISR. Otherwise, the state of the interrupt changes to inactive. – For a pulse interrupt, the NVIC continues to monitor the interrupt signal, and if this is pulsed the state of the interrupt changes to pending and active. In this case, when the processor returns from the ISR the state of the interrupt changes to pending, which might cause the processor to immediately re-enter the ISR. If the interrupt signal is not pulsed while the processor is in the ISR, when the processor returns from the ISR the state of the interrupt changes to inactive. ■ Software writes to the corresponding interrupt clear-pending register bit – For a level-sensitive interrupt, if the interrupt signal is still asserted, the state of the interrupt does not change. Otherwise, the state of the interrupt changes to inactive. – For a pulse interrupt, the state of the interrupt changes to inactive, if the state was pending or to active, if the state was active and pending. 3.1.3 System Control Block (SCB) The System Control Block (SCB) provides system implementation information and system control, including configuration, control, and reporting of the system exceptions. 3.1.4 Memory Protection Unit (MPU) This section describes the Memory protection unit (MPU). The MPU divides the memory map into a number of regions and defines the location, size, access permissions, and memory attributes of each region. The MPU supports independent attribute settings for each region, overlapping regions, and export of memory attributes to the system. The memory attributes affect the behavior of memory accesses to the region. The Cortex-M4 MPU defines eight separate memory regions, 0-7, and a background region. When memory regions overlap, a memory access is affected by the attributes of the region with the highest number. For example, the attributes for region 7 take precedence over the attributes of any region that overlaps region 7. The background region has the same memory access attributes as the default memory map, but is accessible from privileged software only. The Cortex-M4 MPU memory map is unified, meaning that instruction accesses and data accesses have the same region settings. If a program accesses a memory location that is prohibited by the MPU, the processor generates a memory management fault, causing a fault exception and possibly causing termination of the process in an OS environment. In an OS environment, the kernel can update the MPU region setting dynamically based on the process to be executed. Typically, an embedded OS uses the MPU for memory protection. Configuration of MPU regions is based on memory types (see “Memory Regions, Types and Attributes” on page 95 for more information). November 08, 2011 127 Texas Instruments-Advance Information Cortex-M4 Peripherals Table 3-2 on page 128 shows the possible MPU region attributes. See the section called “MPU Configuration for a Stellaris Microcontroller” on page 132 for guidelines for programming a microcontroller implementation. Table 3-2. Memory Attributes Summary Memory Type Description Strongly Ordered All accesses to Strongly Ordered memory occur in program order. Device Memory-mapped peripherals Normal Normal memory To avoid unexpected behavior, disable the interrupts before updating the attributes of a region that the interrupt handlers might access. Ensure software uses aligned accesses of the correct size to access MPU registers: ■ Except for the MPU Region Attribute and Size (MPUATTR) register, all MPU registers must be accessed with aligned word accesses. ■ The MPUATTR register can be accessed with byte or aligned halfword or word accesses. The processor does not support unaligned accesses to MPU registers. When setting up the MPU, and if the MPU has previously been programmed, disable unused regions to prevent any previous region settings from affecting the new MPU setup. 3.1.4.1 Updating an MPU Region To update the attributes for an MPU region, the MPU Region Number (MPUNUMBER), MPU Region Base Address (MPUBASE) and MPUATTR registers must be updated. Each register can be programmed separately or with a multiple-word write to program all of these registers. You can use the MPUBASEx and MPUATTRx aliases to program up to four regions simultaneously using an STM instruction. Updating an MPU Region Using Separate Words This example simple code configures one region: ; R1 = region number ; R2 = size/enable ; R3 = attributes ; R4 = address LDR R0,=MPUNUMBER STR R1, [R0, #0x0] STR R4, [R0, #0x4] STRH R2, [R0, #0x8] STRH R3, [R0, #0xA] ; ; ; ; ; 0xE000ED98, MPU region number register Region Number Region Base Address Region Size and Enable Region Attribute Disable a region before writing new region settings to the MPU if you have previously enabled the region being changed. For example: ; R1 = region number ; R2 = size/enable ; R3 = attributes ; R4 = address LDR R0,=MPUNUMBER ; 0xE000ED98, MPU region number register 128 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller STR R1, [R0, #0x0] BIC R2, R2, #1 STRH R2, [R0, #0x8] STR R4, [R0, #0x4] STRH R3, [R0, #0xA] ORR R2, #1 STRH R2, [R0, #0x8] ; ; ; ; ; ; ; Region Number Disable Region Size and Enable Region Base Address Region Attribute Enable Region Size and Enable Software must use memory barrier instructions: ■ Before MPU setup, if there might be outstanding memory transfers, such as buffered writes, that might be affected by the change in MPU settings. ■ After MPU setup, if it includes memory transfers that must use the new MPU settings. However, memory barrier instructions are not required if the MPU setup process starts by entering an exception handler, or is followed by an exception return, because the exception entry and exception return mechanism cause memory barrier behavior. Software does not need any memory barrier instructions during MPU setup, because it accesses the MPU through the Private Peripheral Bus (PPB), which is a Strongly Ordered memory region. For example, if all of the memory access behavior is intended to take effect immediately after the programming sequence, then a DSB instruction and an ISB instruction should be used. A DSB is required after changing MPU settings, such as at the end of context switch. An ISB is required if the code that programs the MPU region or regions is entered using a branch or call. If the programming sequence is entered using a return from exception, or by taking an exception, then an ISB is not required. Updating an MPU Region Using Multi-Word Writes The MPU can be programmed directly using multi-word writes, depending how the information is divided. Consider the following reprogramming: ; R1 = region number ; R2 = address ; R3 = size, attributes in one LDR R0, =MPUNUMBER ; 0xE000ED98, MPU region number register STR R1, [R0, #0x0] ; Region Number STR R2, [R0, #0x4] ; Region Base Address STR R3, [R0, #0x8] ; Region Attribute, Size and Enable An STM instruction can be used to optimize this: ; R1 = region number ; R2 = address ; R3 = size, attributes in one LDR R0, =MPUNUMBER ; 0xE000ED98, MPU region number register STM R0, {R1-R3} ; Region number, address, attribute, size and enable This operation can be done in two words for pre-packed information, meaning that the MPU Region Base Address (MPUBASE) register (see page 192) contains the required region number and has the VALID bit set. This method can be used when the data is statically packed, for example in a boot loader: November 08, 2011 129 Texas Instruments-Advance Information Cortex-M4 Peripherals ; R1 = address and region number in one ; R2 = size and attributes in one LDR R0, =MPUBASE ; 0xE000ED9C, MPU Region Base register STR R1, [R0, #0x0] ; Region base address and region number combined ; with VALID (bit 4) set STR R2, [R0, #0x4] ; Region Attribute, Size and Enable Subregions Regions of 256 bytes or more are divided into eight equal-sized subregions. Set the corresponding bit in the SRD field of the MPU Region Attribute and Size (MPUATTR) register (see page 194) to disable a subregion. The least-significant bit of the SRD field controls the first subregion, and the most-significant bit controls the last subregion. Disabling a subregion means another region overlapping the disabled range matches instead. If no other enabled region overlaps the disabled subregion, the MPU issues a fault. Regions of 32, 64, and 128 bytes do not support subregions. With regions of these sizes, the SRD field must be configured to 0x00, otherwise the MPU behavior is unpredictable. Example of SRD Use Two regions with the same base address overlap. Region one is 128 KB, and region two is 512 KB. To ensure the attributes from region one apply to the first 128 KB region, configure the SRD field for region two to 0x03 to disable the first two subregions, as Figure 3-1 on page 130 shows. Figure 3-1. SRD Use Example Region 2, with subregions Region 1 Base address of both regions 3.1.4.2 Offset from base address 512KB 448KB 384KB 320KB 256KB 192KB 128KB Disabled subregion 64KB Disabled subregion 0 MPU Access Permission Attributes The access permission bits, TEX, S, C, B, AP, and XN of the MPUATTR register, control access to the corresponding memory region. If an access is made to an area of memory without the required permissions, then the MPU generates a permission fault. Table 3-3 on page 130 shows the encodings for the TEX, C, B, and S access permission bits. All encodings are shown for completeness, however the current implementation of the Cortex-M4 does not support the concept of cacheability or shareability. Refer to the section called “MPU Configuration for a Stellaris Microcontroller” on page 132 for information on programming the MPU for Stellaris implementations. Table 3-3. TEX, S, C, and B Bit Field Encoding TEX S 000b x 000 B Memory Type Shareability Other Attributes 0 0 Strongly Ordered Shareable - a 0 1 Device Shareable - x C a 130 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 3-3. TEX, S, C, and B Bit Field Encoding (continued) TEX S C B Memory Type Shareability Other Attributes 000 0 1 0 Normal Not shareable 000 1 1 0 Normal Shareable 000 0 1 1 Normal Not shareable 000 1 1 1 Normal Shareable 001 0 0 0 Normal Not shareable 001 1 0 0 Normal Shareable Outer and inner noncacheable. 001 x a 0 1 Reserved encoding - - a Outer and inner write-through. No write allocate. 001 x 1 0 Reserved encoding - - 001 0 1 1 Normal Not shareable 001 1 1 1 Normal Shareable Outer and inner write-back. Write and read allocate. 010 x a 0 0 Device Not shareable Nonshared Device. a a 010 x 0 1 Reserved encoding - - 010 x 1 x Reserved encoding - - 1BB 0 A A Normal Not shareable 1BB 1 A A Normal Shareable Cached memory (BB = outer policy, AA = inner policy). a See Table 3-4 for the encoding of the AA and BB bits. a. The MPU ignores the value of this bit. Table 3-4 on page 131 shows the cache policy for memory attribute encodings with a TEX value in the range of 0x4-0x7. Table 3-4. Cache Policy for Memory Attribute Encoding Encoding, AA or BB Corresponding Cache Policy 00 Non-cacheable 01 Write back, write and read allocate 10 Write through, no write allocate 11 Write back, no write allocate Table 3-5 on page 131 shows the AP encodings in the MPUATTR register that define the access permissions for privileged and unprivileged software. Table 3-5. AP Bit Field Encoding AP Bit Field Privileged Permissions Unprivileged Permissions Description 000 No access No access All accesses generate a permission fault. 001 R/W No access Access from privileged software only. 010 R/W RO Writes by unprivileged software generate a permission fault. 011 R/W R/W Full access. 100 Unpredictable Unpredictable Reserved. 101 RO No access Reads by privileged software only. November 08, 2011 131 Texas Instruments-Advance Information Cortex-M4 Peripherals Table 3-5. AP Bit Field Encoding (continued) AP Bit Field Privileged Permissions Unprivileged Permissions Description 110 RO RO Read-only, by privileged or unprivileged software. 111 RO RO Read-only, by privileged or unprivileged software. MPU Configuration for a Stellaris Microcontroller Stellaris microcontrollers have only a single processor and no caches. As a result, the MPU should be programmed as shown in Table 3-6 on page 132. Table 3-6. Memory Region Attributes for Stellaris Microcontrollers Memory Region TEX S C B Memory Type and Attributes Flash memory 000b 0 1 0 Normal memory, non-shareable, write-through Internal SRAM 000b 1 1 0 Normal memory, shareable, write-through External SRAM 000b 1 1 1 Normal memory, shareable, write-back, write-allocate Peripherals 000b 1 0 1 Device memory, shareable In current Stellaris microcontroller implementations, the shareability and cache policy attributes do not affect the system behavior. However, using these settings for the MPU regions can make the application code more portable. The values given are for typical situations. 3.1.4.3 MPU Mismatch When an access violates the MPU permissions, the processor generates a memory management fault (see “Exceptions and Interrupts” on page 92 for more information). The MFAULTSTAT register indicates the cause of the fault. See page 179 for more information. 3.1.5 Floating-Point Unit (FPU) This section describes the Floating-Point Unit (FPU) and the registers it uses. The FPU provides: ■ 32-bit instructions for single-precision (C float) data-processing operations ■ Combined Multiply and Accumulate instructions for increased precision (Fused MAC) ■ Hardware support for conversion, addition, subtraction, multiplication with optional accumulate, division, and square-root ■ Hardware support for denormals and all IEEE rounding modes ■ 32 dedicated 32-bit single-precision registers, also addressable as 16 double-word registers ■ Decoupled three stage pipeline The Cortex-M4F FPU fully supports single-precision add, subtract, multiply, divide, multiply and accumulate, and square root operations. It also provides conversions between fixed-point and floating-point data formats, and floating-point constant instructions. The FPU provides floating-point computation functionality that is compliant with the ANSI/IEEE Std 754-2008, IEEE Standard for Binary Floating-Point Arithmetic, referred to as the IEEE 754 standard. The FPU's single-precision extension registers can also be accessed as 16 doubleword registers for load, store, and move operations. 132 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 3.1.5.1 FPU Views of the Register Bank The FPU provides an extension register file containing 32 single-precision registers. These can be viewed as: ■ Sixteen 64-bit doubleword registers, D0-D15 ■ Thirty-two 32-bit single-word registers, S0-S31 ■ A combination of registers from the above views Figure 3-2. FPU Register Bank S0 S1 S2 S3 S4 S5 S6 S7 ... S28 S29 S30 S31 D0 D1 D2 D3 ... D14 D15 The mapping between the registers is as follows: ■ S maps to the least significant half of D ■ S maps to the most significant half of D For example, you can access the least significant half of the value in D6 by accessing S12, and the most significant half of the elements by accessing S13. 3.1.5.2 Modes of Operation The FPU provides three modes of operation to accommodate a variety of applications. Full-Compliance mode. In Full-Compliance mode, the FPU processes all operations according to the IEEE 754 standard in hardware. Flush-to-Zero mode. Setting the FZ bit of the Floating-Point Status and Control (FPSC) register enables Flush-to-Zero mode. In this mode, the FPU treats all subnormal input operands of arithmetic CDP operations as zeros in the operation. Exceptions that result from a zero operand are signalled appropriately. VABS, VNEG, and VMOV are not considered arithmetic CDP operations and are not affected by Flush-to-Zero mode. A result that is tiny, as described in the IEEE 754 standard, where the destination precision is smaller in magnitude than the minimum normal value before rounding, is replaced with a zero. The IDC bit in FPSC indicates when an input flush occurs. The UFC bit in FPSC indicates when a result flush occurs. Default NaN mode. Setting the DN bit in the FPSC register enables default NaN mode. In this mode, the result of any arithmetic data processing operation that involves an input NaN, or that generates a NaN result, returns the default NaN. Propagation of the fraction bits is maintained only by VABS, November 08, 2011 133 Texas Instruments-Advance Information Cortex-M4 Peripherals VNEG, and VMOV operations. All other CDP operations ignore any information in the fraction bits of an input NaN. 3.1.5.3 Compliance with the IEEE 754 standard When Default NaN (DN) and Flush-to-Zero (FZ) modes are disabled, FPv4 functionality is compliant with the IEEE 754 standard in hardware. No support code is required to achieve this compliance. 3.1.5.4 Complete Implementation of the IEEE 754 standard The Cortex-M4F floating point instruction set does not support all operations defined in the IEEE 754-2008 standard. Unsupported operations include, but are not limited to the following: ■ Remainder ■ Round floating-point number to integer-valued floating-point number ■ Binary-to-decimal conversions ■ Decimal-to-binary conversions ■ Direct comparison of single-precision and double-precision values The Cortex-M4 FPU supports fused MAC operations as described in the IEEE standard. For complete implementation of the IEEE 754-2008 standard, floating-point functionality must be augmented with library functions. 3.1.5.5 IEEE 754 standard implementation choices NaN handling All single-precision values with the maximum exponent field value and a nonzero fraction field are valid NaNs. A most-significant fraction bit of zero indicates a Signaling NaN (SNaN). A one indicates a Quiet NaN (QNaN). Two NaN values are treated as different NaNs if they differ in any bit. The below table shows the default NaN values. Sign Fraction Fraction 0 0xFF bit [22] = 1, bits [21:0] are all zeros Processing of input NaNs for ARM floating-point functionality and libraries is defined as follows: ■ In full-compliance mode, NaNs are handled as described in the ARM Architecture Reference Manual. The hardware processes the NaNs directly for arithmetic CDP instructions. For data transfer operations, NaNs are transferred without raising the Invalid Operation exception. For the non-arithmetic CDP instructions, VABS, VNEG, and VMOV, NaNs are copied, with a change of sign if specified in the instructions, without causing the Invalid Operation exception. ■ In default NaN mode, arithmetic CDP instructions involving NaN operands return the default NaN regardless of the fractions of any NaN operands. SNaNs in an arithmetic CDP operation set the IOC flag, FPSCR[0]. NaN handling by data transfer and non-arithmetic CDP instructions is the same as in full-compliance mode. 134 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 3-7. QNaN and SNaN Handling Instruction Type Default NaN Mode With QNaN Operand With SNaN Operand Off The QNaN or one of the QNaN operands, if there is more than one, is returned according to the rules given in the ARM Architecture Reference Manual. IOC set. The SNaN is quieted and the result NaN is determined by the rules given in the ARM Architecture Reference Manual. On Default NaN returns. IOCa set. Default NaN returns. Arithmetic CDP a Non-arithmetic CDP Off/On NaN passes to destination with sign changed as appropriate. FCMP(Z) - Unordered compare. IOC set. Unordered compare. FCMPE(Z) - IOC set. Unordered compare. IOC set. Unordered compare. Load/store Off/On All NaNs transferred. a. IOC is the Invalid Operation exception flag, FPSCR[0]. Comparisons Comparison results modify the flags in the FPSCR. You can use the MVRS APSR_nzcv instruction (formerly FMSTAT) to transfer the current flags from the FPSCR to the APSR. See the ARM Architecture Reference Manual for mapping of IEEE 754-2008 standard predicates to ARM conditions. The flags used are chosen so that subsequent conditional execution of ARM instructions can test the predicates defined in the IEEE standard. Underflow The Cortex-M4F FPU uses the before rounding form of tininess and the inexact result form of loss of accuracy as described in the IEEE 754-2008 standard to generate Underflow exceptions. In flush-to-zero mode, results that are tiny before rounding, as described in the IEEE standard, are flushed to a zero, and the UFC flag, FPSCR[3], is set. See the ARM Architecture Reference Manual for information on flush-to-zero mode. When the FPU is not in flush-to-zero mode, operations are performed on subnormal operands. If the operation does not produce a tiny result, it returns the computed result, and the UFC flag, FPSCR[3], is not set. The IXC flag, FPSCR[4], is set if the operation is inexact. If the operation produces a tiny result, the result is a subnormal or zero value, and the UFC flag, FPSCR[3], is set if the result was also inexact. 3.1.5.6 Exceptions The FPU sets the cumulative exception status flag in the FPSCR register as required for each instruction, in accordance with the FPv4 architecture. The FPU does not support user-mode traps. The exception enable bits in the FPSCR read-as-zero, and writes are ignored. The processor also has six output pins, FPIXC, FPUFC, FPOFC, FPDZC, FPIDC, and FPIOC, that each reflect the status of one of the cumulative exception flags. See the Cortex-M4 Integration and Implementation Manual for a description of these outputs. The processor can reduce the exception latency by using lazy stacking. See Auxiliary Control Register, ACTLR on page 4-5. This means that the processor reserves space on the stack for the FP state, but does not save that state information to the stack. See the ARMv7-M Architecture Reference Manual for more information. 3.1.5.7 Enabling the FPU The FPU is disabled from reset. You must enable it before you can use any floating-point instructions. The processor must be in privileged mode to read from and write to the Coprocessor Access November 08, 2011 135 Texas Instruments-Advance Information Cortex-M4 Peripherals Control (CPAC) register. The below example code sequence enables the FPU in both privileged and user modes. ; CPACR is located at address 0xE000ED88 LDR.W R0, =0xE000ED88 ; Read CPACR LDR R1, [R0] ; Set bits 20-23 to enable CP10 and CP11 coprocessors ORR R1, R1, #(0xF 0, then the conversion result > 0x800 (range is 0x800–0xFFF) ■ If ∆V < 0, then the conversion result < 0x800 (range is 0–0x800) The differential pairs assign polarities to the analog inputs: the even-numbered input is always positive, and the odd-numbered input is always negative. In order for a valid conversion result to appear, the negative input must be in the range of ± (VREFA+ - VREFA-) of the positive input. If an analog input is greater than VREFA+ or less than VREFA- (the valid range for analog inputs), the input voltage is clipped, meaning it appears as either VREFA+ or VREFA- , respectively, to the ADC. Because both inputs can swing from VREFA- to VREFA+, the maximum difference in the signal voltage is 2 x (VREFA+ - VREFA-). As a result, the ADC codes are interpreted as: mV per ADC code = (2 *(VREFA+ - VREFA-)) / 4096 Figure 13-10 shows how the differential voltage, ∆V, is represented in ADC codes. 840 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 13-10. Differential Voltage Representation 0xFFF 0x800 -(VREFA+ - VREFA-) 0 VREFA+ - VREFA- V - Input Saturation 13.3.6 Internal Temperature Sensor The temperature sensor serves two primary purposes: 1) to notify the system that internal temperature is too high or low for reliable operation and 2) to provide temperature measurements for calibration of the Hibernate module RTC trim value. The temperature sensor does not have a separate enable, because it also contains the bandgap reference and must always be enabled. The reference is supplied to other analog modules; not just the ADC. In addition, the temperature sensor has a second power-down input in the 3.3 V domain which provides control by the Hibernation module. The internal temperature sensor provides an analog temperature reading as well as a reference voltage. This reference voltage, SENSO, is given by the following equation: SENSO = 2.7 - ((T + 55) / 75) This relation is shown in Figure 13-11 on page 842. November 08, 2011 841 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Figure 13-11. Internal Temperature Sensor Characteristic Sensor = 2.7 V – (T+55) 75 Sensor 2.7 V 1.633 V 0.3 V -55° C 25° C 125° C Temp The temperature sensor reading can be sampled in a sample sequence by setting the TSn bit in the ADCSSCTLn register. The temperature reading from the temperature sensor can also be given as a function of the ADC value. The following formula calculates temperature (in ℃) based on the ADC reading: Temperature = 147.5 - ((225 × ADC) / 4095) 13.3.7 Digital Comparator Unit An ADC is commonly used to sample an external signal and to monitor its value to ensure that it remains in a given range. To automate this monitoring procedure and reduce the amount of processor overhead that is required, each module provides eight digital comparators. Conversions from the ADC that are sent to the digital comparators are compared against the user programmable limits in the ADC Digital Comparator Range (ADCDCCMPn) registers. If the observed signal moves out of the acceptable range, a processor interrupt can be generated and/or a trigger can be sent to the PWM module. The digital comparators four operational modes (Once, Always, Hysteresis Once, Hysteresis Always) can be applied to three separate regions (low band, mid band, high band) as defined by the user. 13.3.7.1 Output Functions ADC conversions can either be stored in the ADC Sample Sequence FIFOs or compared using the digital comparator resources as defined by the SnDCOP bits in the ADC Sample Sequence n Operation (ADCSSOPn) register. These selected ADC conversions are used by their respective digital comparator to monitor the external signal. Each comparator has two possible output functions: processor interrupts and triggers. 842 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Each function has its own state machine to track the monitored signal. Even though the interrupt and trigger functions can be enabled individually or both at the same time, the same conversion data is used by each function to determine if the right conditions have been met to assert the associated output. Interrupts The digital comparator interrupt function is enabled by setting the CIE bit in the ADC Digital Comparator Control (ADCDCCTLn) register. This bit enables the interrupt function state machine to start monitoring the incoming ADC conversions. When the appropriate set of conditions is met, and the DCONSSx bit is set in the ADCIM register, an interrupt is sent to the interrupt controller. Triggers The digital comparator trigger function is enabled by setting the CTE bit in the ADCDCCTLn register. This bit enables the trigger function state machine to start monitoring the incoming ADC conversions. When the appropriate set of conditions is met, the corresponding digital comparator trigger to the PWM module is asserted 13.3.7.2 Operational Modes Four operational modes are provided to support a broad range of applications and multiple possible signaling requirements: Always, Once, Hysteresis Always, and Hysteresis Once. The operational mode is selected using the CIM or CTM field in the ADCDCCTLn register. Always Mode In the Always operational mode, the associated interrupt or trigger is asserted whenever the ADC conversion value meets its comparison criteria. The result is a string of assertions on the interrupt or trigger while the conversions are within the appropriate range. Once Mode In the Once operational mode, the associated interrupt or trigger is asserted whenever the ADC conversion value meets its comparison criteria, and the previous ADC conversion value did not. The result is a single assertion of the interrupt or trigger when the conversions are within the appropriate range. Hysteresis-Always Mode The Hysteresis-Always operational mode can only be used in conjunction with the low-band or high-band regions because the mid-band region must be crossed and the opposite region entered to clear the hysteresis condition. In the Hysteresis-Always mode, the associated interrupt or trigger is asserted in the following cases: 1) the ADC conversion value meets its comparison criteria or 2) a previous ADC conversion value has met the comparison criteria, and the hysteresis condition has not been cleared by entering the opposite region. The result is a string of assertions on the interrupt or trigger that continue until the opposite region is entered. Hysteresis-Once Mode The Hysteresis-Once operational mode can only be used in conjunction with the low-band or high-band regions because the mid-band region must be crossed and the opposite region entered to clear the hysteresis condition. In the Hysteresis-Once mode, the associated interrupt or trigger is asserted only when the ADC conversion value meets its comparison criteria, the hysteresis condition is clear, and the previous ADC conversion did not meet the comparison criteria. The result is a single assertion on the interrupt or trigger. November 08, 2011 843 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) 13.3.7.3 Function Ranges The two comparison values, COMP0 and COMP1, in the ADC Digital Comparator Range (ADCDCCMPn) register effectively break the conversion area into three distinct regions. These regions are referred to as the low-band (less than or equal to COMP0), mid-band (greater than COMP0 but less than or equal to COMP1), and high-band (greater than COMP1) regions. COMP0 and COMP1 may be programmed to the same value, effectively creating two regions, but COMP1 must always be greater than or equal to the value of COMP0. A COMP1 value that is less than COMP0 generates unpredictable results. Low-Band Operation To operate in the low-band region, either the CIC field or the CTC field in the ADCDCCTLn register must be programmed to 0x0. This setting causes interrupts or triggers to be generated in the low-band region as defined by the programmed operational mode. An example of the state of the interrupt/trigger signal in the low-band region for each of the operational modes is shown in Figure 13-12 on page 844. Note that a "0" in a column following the operational mode name (Always, Once, Hysteresis Always, and Hysteresis Once) indicates that the interrupt or trigger signal is de-asserted and a "1" indicates that the signal is asserted. Figure 13-12. Low-Band Operation (CIC=0x0 and/or CTC=0x0) COMP1 COMP0 Always – 0 0 0 0 1 1 1 0 0 1 1 0 0 0 0 1 Once – 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 1 Hysteresis Always – 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 1 Hysteresis Once – 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 1 Mid-Band Operation To operate in the mid-band region, either the CIC field or the CTC field in the ADCDCCTLn register must be programmed to 0x1. This setting causes interrupts or triggers to be generated in the mid-band region according the operation mode. Only the Always and Once operational modes are available in the mid-band region. An example of the state of the interrupt/trigger signal in the mid-band region for each of the allowed operational modes is shown in Figure 13-13 on page 845. Note that a "0" in 844 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller a column following the operational mode name (Always or Once) indicates that the interrupt or trigger signal is de-asserted and a "1" indicates that the signal is asserted. Figure 13-13. Mid-Band Operation (CIC=0x1 and/or CTC=0x1) COMP1 COMP0 Always – 0 0 1 1 0 0 0 1 1 1 0 0 1 1 0 0 Once – 0 0 1 0 0 0 0 1 0 0 0 0 1 0 0 0 Hysteresis Always – - - - - - - - - - - - - - - - - Hysteresis Once – - - - - - - - - - - - - - - - - High-Band Operation To operate in the high-band region, either the CIC field or the CTC field in the ADCDCCTLn register must be programmed to 0x3. This setting causes interrupts or triggers to be generated in the high-band region according the operation mode. An example of the state of the interrupt/trigger signal in the high-band region for each of the allowed operational modes is shown in Figure 13-14 on page 846. Note that a "0" in a column following the operational mode name (Always, Once, Hysteresis Always, and Hysteresis Once) indicates that the interrupt or trigger signal is de-asserted and a "1" indicates that the signal is asserted. November 08, 2011 845 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Figure 13-14. High-Band Operation (CIC=0x3 and/or CTC=0x3) COMP1 COMP0 13.4 Always – 0 0 0 0 1 1 1 0 0 1 1 0 0 0 1 1 Once – 0 0 0 0 1 0 0 0 0 1 0 0 0 0 1 0 Hysteresis Always – 0 0 0 0 1 1 1 1 1 1 1 1 0 0 1 1 Hysteresis Once – 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 Initialization and Configuration In order for the ADC module to be used, the PLL must be enabled and programmed to a supported crystal frequency in the RCC register (see page 280). Using unsupported frequencies can cause faulty operation in the ADC module. 13.4.1 Module Initialization Initialization of the ADC module is a simple process with very few steps: enabling the clock to the ADC, disabling the analog isolation circuit associated with all inputs that are to be used, and reconfiguring the sample sequencer priorities (if needed). The initialization sequence for the ADC is as follows: 1. Enable the ADC clock using the RCGCADC register (see page 402). 2. Enable the clock to the appropriate GPIO modules via the RCGCGPIO register (see page 389). To find out which GPIO ports to enable, refer to “Signal Description” on page 831. 3. Set the GPIO AFSEL bits for the ADC input pins (see page 698). To determine which GPIOs to configure, see Table 23-4 on page 1387. 4. Configure the AINx signals to be analog inputs by clearing the corresponding DEN bit in the GPIO Digital Enable (GPIODEN) register (see page 710). 5. Disable the analog isolation circuit for all ADC input pins that are to be used by writing a 1 to the appropriate bits of the GPIOAMSEL register (see page 715) in the associated GPIO block. 846 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 6. If required by the application, reconfigure the sample sequencer priorities in the ADCSSPRI register. The default configuration has Sample Sequencer 0 with the highest priority and Sample Sequencer 3 as the lowest priority. 13.4.2 Sample Sequencer Configuration Configuration of the sample sequencers is slightly more complex than the module initialization because each sample sequencer is completely programmable. The configuration for each sample sequencer should be as follows: 1. Ensure that the sample sequencer is disabled by clearing the corresponding ASENn bit in the ADCACTSS register. Programming of the sample sequencers is allowed without having them enabled. Disabling the sequencer during programming prevents erroneous execution if a trigger event were to occur during the configuration process. 2. Configure the trigger event for the sample sequencer in the ADCEMUX register. 3. For each sample in the sample sequence, configure the corresponding input source in the ADCSSMUXn and ADCSSEMUXn registers. 4. For each sample in the sample sequence, configure the sample control bits in the corresponding nibble in the ADCSSCTLn register. When programming the last nibble, ensure that the END bit is set. Failure to set the END bit causes unpredictable behavior. 5. If interrupts are to be used, set the corresponding MASK bit in the ADCIM register. 6. Enable the sample sequencer logic by setting the corresponding ASENn bit in the ADCACTSS register. 13.5 Register Map Table 13-4 on page 847 lists the ADC registers. The offset listed is a hexadecimal increment to the register’s address, relative to that ADC module's base address of: ■ ADC0: 0x4003.8000 ■ ADC1: 0x4003.9000 Note that the ADC module clock must be enabled before the registers can be programmed (see page 402). There must be a delay of 3 system clocks after the ADC module clock is enabled before any ADC module registers are accessed. Table 13-4. ADC Register Map Description See page Offset Name Type Reset 0x000 ADCACTSS R/W 0x0000.0000 ADC Active Sample Sequencer 850 0x004 ADCRIS RO 0x0000.0000 ADC Raw Interrupt Status 851 0x008 ADCIM R/W 0x0000.0000 ADC Interrupt Mask 853 0x00C ADCISC R/W1C 0x0000.0000 ADC Interrupt Status and Clear 855 0x010 ADCOSTAT R/W1C 0x0000.0000 ADC Overflow Status 858 0x014 ADCEMUX R/W 0x0000.0000 ADC Event Multiplexer Select 860 November 08, 2011 847 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Table 13-4. ADC Register Map (continued) Offset Name 0x018 See page Type Reset Description ADCUSTAT R/W1C 0x0000.0000 ADC Underflow Status 865 0x01C ADCTSSEL R/W 0x0000.0000 ADC Trigger Source Select 866 0x020 ADCSSPRI R/W 0x0000.3210 ADC Sample Sequencer Priority 868 0x024 ADCSPC R/W 0x0000.0000 ADC Sample Phase Control 870 0x028 ADCPSSI R/W - ADC Processor Sample Sequence Initiate 872 0x030 ADCSAC R/W 0x0000.0000 ADC Sample Averaging Control 874 0x034 ADCDCISC R/W1C 0x0000.0000 ADC Digital Comparator Interrupt Status and Clear 875 0x038 ADCCTL R/W 0x0000.0000 ADC Control 877 0x040 ADCSSMUX0 R/W 0x0000.0000 ADC Sample Sequence Input Multiplexer Select 0 878 0x044 ADCSSCTL0 R/W 0x0000.0000 ADC Sample Sequence Control 0 880 0x048 ADCSSFIFO0 RO - ADC Sample Sequence Result FIFO 0 883 0x04C ADCSSFSTAT0 RO 0x0000.0100 ADC Sample Sequence FIFO 0 Status 884 0x050 ADCSSOP0 R/W 0x0000.0000 ADC Sample Sequence 0 Operation 886 0x054 ADCSSDC0 R/W 0x0000.0000 ADC Sample Sequence 0 Digital Comparator Select 888 0x058 ADCSSEMUX0 R/W 0x0000.0000 ADC Sample Sequence Extended Input Multiplexer Select 0 890 0x060 ADCSSMUX1 R/W 0x0000.0000 ADC Sample Sequence Input Multiplexer Select 1 892 0x064 ADCSSCTL1 R/W 0x0000.0000 ADC Sample Sequence Control 1 893 0x068 ADCSSFIFO1 RO - ADC Sample Sequence Result FIFO 1 883 0x06C ADCSSFSTAT1 RO 0x0000.0100 ADC Sample Sequence FIFO 1 Status 884 0x070 ADCSSOP1 R/W 0x0000.0000 ADC Sample Sequence 1 Operation 895 0x074 ADCSSDC1 R/W 0x0000.0000 ADC Sample Sequence 1 Digital Comparator Select 896 0x078 ADCSSEMUX1 R/W 0x0000.0000 ADC Sample Sequence Extended Input Multiplexer Select 1 898 0x080 ADCSSMUX2 R/W 0x0000.0000 ADC Sample Sequence Input Multiplexer Select 2 892 0x084 ADCSSCTL2 R/W 0x0000.0000 ADC Sample Sequence Control 2 893 0x088 ADCSSFIFO2 RO - ADC Sample Sequence Result FIFO 2 883 0x08C ADCSSFSTAT2 RO 0x0000.0100 ADC Sample Sequence FIFO 2 Status 884 0x090 ADCSSOP2 R/W 0x0000.0000 ADC Sample Sequence 2 Operation 895 0x094 ADCSSDC2 R/W 0x0000.0000 ADC Sample Sequence 2 Digital Comparator Select 896 0x098 ADCSSEMUX2 R/W 0x0000.0000 ADC Sample Sequence Extended Input Multiplexer Select 2 898 0x0A0 ADCSSMUX3 R/W 0x0000.0000 ADC Sample Sequence Input Multiplexer Select 3 900 848 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 13-4. ADC Register Map (continued) Offset Name Type Reset 0x0A4 ADCSSCTL3 R/W 0x0000.0002 0x0A8 ADCSSFIFO3 RO 0x0AC ADCSSFSTAT3 0x0B0 Description See page ADC Sample Sequence Control 3 901 - ADC Sample Sequence Result FIFO 3 883 RO 0x0000.0100 ADC Sample Sequence FIFO 3 Status 884 ADCSSOP3 R/W 0x0000.0000 ADC Sample Sequence 3 Operation 902 0x0B4 ADCSSDC3 R/W 0x0000.0000 ADC Sample Sequence 3 Digital Comparator Select 903 0x0B8 ADCSSEMUX3 R/W 0x0000.0000 ADC Sample Sequence Extended Input Multiplexer Select 3 904 0xD00 ADCDCRIC R/W 0x0000.0000 ADC Digital Comparator Reset Initial Conditions 905 0xE00 ADCDCCTL0 R/W 0x0000.0000 ADC Digital Comparator Control 0 910 0xE04 ADCDCCTL1 R/W 0x0000.0000 ADC Digital Comparator Control 1 910 0xE08 ADCDCCTL2 R/W 0x0000.0000 ADC Digital Comparator Control 2 910 0xE0C ADCDCCTL3 R/W 0x0000.0000 ADC Digital Comparator Control 3 910 0xE10 ADCDCCTL4 R/W 0x0000.0000 ADC Digital Comparator Control 4 910 0xE14 ADCDCCTL5 R/W 0x0000.0000 ADC Digital Comparator Control 5 910 0xE18 ADCDCCTL6 R/W 0x0000.0000 ADC Digital Comparator Control 6 910 0xE1C ADCDCCTL7 R/W 0x0000.0000 ADC Digital Comparator Control 7 910 0xE40 ADCDCCMP0 R/W 0x0000.0000 ADC Digital Comparator Range 0 913 0xE44 ADCDCCMP1 R/W 0x0000.0000 ADC Digital Comparator Range 1 913 0xE48 ADCDCCMP2 R/W 0x0000.0000 ADC Digital Comparator Range 2 913 0xE4C ADCDCCMP3 R/W 0x0000.0000 ADC Digital Comparator Range 3 913 0xE50 ADCDCCMP4 R/W 0x0000.0000 ADC Digital Comparator Range 4 913 0xE54 ADCDCCMP5 R/W 0x0000.0000 ADC Digital Comparator Range 5 913 0xE58 ADCDCCMP6 R/W 0x0000.0000 ADC Digital Comparator Range 6 913 0xE5C ADCDCCMP7 R/W 0x0000.0000 ADC Digital Comparator Range 7 913 0xFC0 ADCPP RO 0x00B0.2187 ADC Peripheral Properties 914 0xFC4 ADCPC R/W 0x0000.0007 ADC Peripheral Configuration 916 0xFC8 ADCCC R/W 0x0000.0000 ADC Clock Configuration 917 13.6 Register Descriptions The remainder of this section lists and describes the ADC registers, in numerical order by address offset. November 08, 2011 849 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 1: ADC Active Sample Sequencer (ADCACTSS), offset 0x000 This register controls the activation of the sample sequencers. Each sample sequencer can be enabled or disabled independently. ADC Active Sample Sequencer (ADCACTSS) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 ASEN3 ASEN2 ASEN1 ASEN0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 ASEN3 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. ADC SS3 Enable Value Description 2 ASEN2 R/W 0 1 Sample Sequencer 3 is enabled. 0 Sample Sequencer 3 is disabled. ADC SS2 Enable Value Description 1 ASEN1 R/W 0 1 Sample Sequencer 2 is enabled. 0 Sample Sequencer 2 is disabled. ADC SS1 Enable Value Description 0 ASEN0 R/W 0 1 Sample Sequencer 1 is enabled. 0 Sample Sequencer 1 is disabled. ADC SS0 Enable Value Description 1 Sample Sequencer 0 is enabled. 0 Sample Sequencer 0 is disabled. 850 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 2: ADC Raw Interrupt Status (ADCRIS), offset 0x004 This register shows the status of the raw interrupt signal of each sample sequencer. These bits may be polled by software to look for interrupt conditions without sending the interrupts to the interrupt controller. ADC Raw Interrupt Status (ADCRIS) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x004 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 24 23 22 21 20 19 18 17 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 2 1 0 INR3 INR2 INR1 INR0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset INRDC reserved Type Reset 16 Bit/Field Name Type Reset Description 31:17 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 16 INRDC RO 0 Digital Comparator Raw Interrupt Status Value Description 1 At least one bit in the ADCDCISC register is set, meaning that a digital comparator interrupt has occurred. 0 All bits in the ADCDCISC register are clear. 15:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 INR3 RO 0 SS3 Raw Interrupt Status Value Description 1 A sample has completed conversion and the respective ADCSSCTL3 IEn bit is set, enabling a raw interrupt. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the IN3 bit in the ADCISC register. 2 INR2 RO 0 SS2 Raw Interrupt Status Value Description 1 A sample has completed conversion and the respective ADCSSCTL2 IEn bit is set, enabling a raw interrupt. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the IN2 bit in the ADCISC register. November 08, 2011 851 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 1 INR1 RO 0 Description SS1 Raw Interrupt Status Value Description 1 A sample has completed conversion and the respective ADCSSCTL1 IEn bit is set, enabling a raw interrupt. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the IN1 bit in the ADCISC register. 0 INR0 RO 0 SS0 Raw Interrupt Status Value Description 1 A sample has completed conversion and the respective ADCSSCTL0 IEn bit is set, enabling a raw interrupt. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the IN0 bit in the ADCISC register. 852 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 3: ADC Interrupt Mask (ADCIM), offset 0x008 This register controls whether the sample sequencer and digital comparator raw interrupt signals are sent to the interrupt controller. Each raw interrupt signal can be masked independently. Only a single DCONSSn bit should be set at any given time. Setting more than one of these bits results in the INRDC bit from the ADCRIS register being masked, and no interrupt is generated on any of the sample sequencer interrupt lines. ADC Interrupt Mask (ADCIM) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 25 24 23 22 21 20 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 9 8 7 6 5 4 3 2 1 0 MASK3 MASK2 MASK1 MASK0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset 18 17 16 DCONSS3 DCONSS2 DCONSS1 DCONSS0 reserved Type Reset 19 Bit/Field Name Type Reset Description 31:20 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 19 DCONSS3 R/W 0 Digital Comparator Interrupt on SS3 Value Description 18 DCONSS2 R/W 0 1 The raw interrupt signal from the digital comparators (INRDC bit in the ADCRIS register) is sent to the interrupt controller on the SS3 interrupt line. 0 The status of the digital comparators does not affect the SS3 interrupt status. Digital Comparator Interrupt on SS2 Value Description 17 DCONSS1 R/W 0 1 The raw interrupt signal from the digital comparators (INRDC bit in the ADCRIS register) is sent to the interrupt controller on the SS2 interrupt line. 0 The status of the digital comparators does not affect the SS2 interrupt status. Digital Comparator Interrupt on SS1 Value Description 1 The raw interrupt signal from the digital comparators (INRDC bit in the ADCRIS register) is sent to the interrupt controller on the SS1 interrupt line. 0 The status of the digital comparators does not affect the SS1 interrupt status. November 08, 2011 853 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 16 DCONSS0 R/W 0 Description Digital Comparator Interrupt on SS0 Value Description 1 The raw interrupt signal from the digital comparators (INRDC bit in the ADCRIS register) is sent to the interrupt controller on the SS0 interrupt line. 0 The status of the digital comparators does not affect the SS0 interrupt status. 15:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 MASK3 R/W 0 SS3 Interrupt Mask Value Description 2 MASK2 R/W 0 1 The raw interrupt signal from Sample Sequencer 3 (ADCRIS register INR3 bit) is sent to the interrupt controller. 0 The status of Sample Sequencer 3 does not affect the SS3 interrupt status. SS2 Interrupt Mask Value Description 1 MASK1 R/W 0 1 The raw interrupt signal from Sample Sequencer 2 (ADCRIS register INR2 bit) is sent to the interrupt controller. 0 The status of Sample Sequencer 2 does not affect the SS2 interrupt status. SS1 Interrupt Mask Value Description 0 MASK0 R/W 0 1 The raw interrupt signal from Sample Sequencer 1 (ADCRIS register INR1 bit) is sent to the interrupt controller. 0 The status of Sample Sequencer 1 does not affect the SS1 interrupt status. SS0 Interrupt Mask Value Description 1 The raw interrupt signal from Sample Sequencer 0 (ADCRIS register INR0 bit) is sent to the interrupt controller. 0 The status of Sample Sequencer 0 does not affect the SS0 interrupt status. 854 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 4: ADC Interrupt Status and Clear (ADCISC), offset 0x00C This register provides the mechanism for clearing sample sequencer interrupt conditions and shows the status of interrupts generated by the sample sequencers and the digital comparators which have been sent to the interrupt controller. When read, each bit field is the logical AND of the respective INR and MASK bits. Sample sequencer interrupts are cleared by writing a 1 to the corresponding bit position. Digital comparator interrupts are cleared by writing a 1 to the appropriate bits in the ADCDCISC register. If software is polling the ADCRIS instead of generating interrupts, the sample sequence INRn bits are still cleared via the ADCISC register, even if the INn bit is not set. ADC Interrupt Status and Clear (ADCISC) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x00C Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 25 24 23 22 21 20 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 2 1 0 IN3 IN2 IN1 IN0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 reserved Type Reset 18 17 16 DCINSS3 DCINSS2 DCINSS1 DCINSS0 reserved Type Reset 19 Bit/Field Name Type Reset Description 31:20 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 19 DCINSS3 RO 0 Digital Comparator Interrupt Status on SS3 Value Description 1 Both the INRDC bit in the ADCRIS register and the DCONSS3 bit in the ADCIM register are set, providing a level-based interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1 to it. Clearing this bit also clears the INRDC bit in the ADCRIS register. 18 DCINSS2 RO 0 Digital Comparator Interrupt Status on SS2 Value Description 1 Both the INRDC bit in the ADCRIS register and the DCONSS2 bit in the ADCIM register are set, providing a level-based interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1 to it. Clearing this bit also clears the INRDC bit in the ADCRIS register. November 08, 2011 855 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 17 DCINSS1 RO 0 Description Digital Comparator Interrupt Status on SS1 Value Description 1 Both the INRDC bit in the ADCRIS register and the DCONSS1 bit in the ADCIM register are set, providing a level-based interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1 to it. Clearing this bit also clears the INRDC bit in the ADCRIS register. 16 DCINSS0 RO 0 Digital Comparator Interrupt Status on SS0 Value Description 1 Both the INRDC bit in the ADCRIS register and the DCONSS0 bit in the ADCIM register are set, providing a level-based interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1 to it. Clearing this bit also clears the INRDC bit in the ADCRIS register. 15:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 IN3 R/W1C 0 SS3 Interrupt Status and Clear Value Description 1 Both the INR3 bit in the ADCRIS register and the MASK3 bit in the ADCIM register are set, providing a level-based interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INR3 bit in the ADCRIS register. 2 IN2 R/W1C 0 SS2 Interrupt Status and Clear Value Description 1 Both the INR2 bit in the ADCRIS register and the MASK2 bit in the ADCIM register are set, providing a level-based interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INR2 bit in the ADCRIS register. 856 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 IN1 R/W1C 0 Description SS1 Interrupt Status and Clear Value Description 1 Both the INR1 bit in the ADCRIS register and the MASK1 bit in the ADCIM register are set, providing a level-based interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INR1 bit in the ADCRIS register. 0 IN0 R/W1C 0 SS0 Interrupt Status and Clear Value Description 1 Both the INR0 bit in the ADCRIS register and the MASK0 bit in the ADCIM register are set, providing a level-based interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INR0 bit in the ADCRIS register. November 08, 2011 857 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 5: ADC Overflow Status (ADCOSTAT), offset 0x010 This register indicates overflow conditions in the sample sequencer FIFOs. Once the overflow condition has been handled by software, the condition can be cleared by writing a 1 to the corresponding bit position. ADC Overflow Status (ADCOSTAT) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x010 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 OV3 OV2 OV1 OV0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 OV3 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SS3 FIFO Overflow Value Description 1 The FIFO for Sample Sequencer 3 has hit an overflow condition, meaning that the FIFO is full and a write was requested. When an overflow is detected, the most recent write is dropped. 0 The FIFO has not overflowed. This bit is cleared by writing a 1. 2 OV2 R/W1C 0 SS2 FIFO Overflow Value Description 1 The FIFO for Sample Sequencer 2 has hit an overflow condition, meaning that the FIFO is full and a write was requested. When an overflow is detected, the most recent write is dropped. 0 The FIFO has not overflowed. This bit is cleared by writing a 1. 1 OV1 R/W1C 0 SS1 FIFO Overflow Value Description 1 The FIFO for Sample Sequencer 1 has hit an overflow condition, meaning that the FIFO is full and a write was requested. When an overflow is detected, the most recent write is dropped. 0 The FIFO has not overflowed. This bit is cleared by writing a 1. 858 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 0 OV0 R/W1C 0 Description SS0 FIFO Overflow Value Description 1 The FIFO for Sample Sequencer 0 has hit an overflow condition, meaning that the FIFO is full and a write was requested. When an overflow is detected, the most recent write is dropped. 0 The FIFO has not overflowed. This bit is cleared by writing a 1. November 08, 2011 859 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 6: ADC Event Multiplexer Select (ADCEMUX), offset 0x014 The ADCEMUX selects the event (trigger) that initiates sampling for each sample sequencer. Each sample sequencer can be configured with a unique trigger source. When using a PWM generator as the trigger source, use the ADC Trigger Source Select (ADCTSSEL) register to specify in which PWM module the generator is located. ADC Event Multiplexer Select (ADCEMUX) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x014 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset EM3 Type Reset EM2 EM1 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 EM0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 860 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 15:12 EM3 R/W 0x0 Description SS3 Trigger Select This field selects the trigger source for Sample Sequencer 3. The valid configurations for this field are: Value Event 0x0 Processor (default) The trigger is initiated by setting the SSn bit in the ADCPSSI register. 0x1 Analog Comparator 0 This trigger is configured by the Analog Comparator Control 0 (ACCTL0) register (page 1250). 0x2 Analog Comparator 1 This trigger is configured by the Analog Comparator Control 1 (ACCTL1) register (page 1250). 0x3 Analog Comparator 2 This trigger is configured by the Analog Comparator Control 2 (ACCTL2) register (page 1250). 0x4 External (GPIO Pins) This trigger is connected to the GPIO interrupt for the corresponding GPIO (see “ADC Trigger Source” on page 682). 0x5 Timer In addition, the trigger must be enabled with the TnOTE bit in the GPTMCTL register (page 768). 0x6 PWM0 The PWM generator 0 trigger can be configured with the PWM0 Interrupt and Trigger Enable (PWM0INTEN) register (page 1299). 0x7 PWM1 The PWM generator 1 trigger can be configured with the PWM1INTEN register (page 1299). 0x8 PWM2 The PWM generator 2 trigger can be configured with the PWM2INTEN register (page 1299). 0x9 PWM3 The PWM generator 3 trigger can be configured with the PWM3INTEN register (page 1299). 0xA-0xE reserved 0xF Always (continuously sample) November 08, 2011 861 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 11:8 EM2 R/W 0x0 Description SS2 Trigger Select This field selects the trigger source for Sample Sequencer 2. The valid configurations for this field are: Value Event 0x0 Processor (default) The trigger is initiated by setting the SSn bit in the ADCPSSI register. 0x1 Analog Comparator 0 This trigger is configured by the Analog Comparator Control 0 (ACCTL0) register (page 1250). 0x2 Analog Comparator 1 This trigger is configured by the Analog Comparator Control 1 (ACCTL1) register (page 1250). 0x3 Analog Comparator 2 This trigger is configured by the Analog Comparator Control 2 (ACCTL2) register (page 1250). 0x4 External (GPIO Pins) This trigger is connected to the GPIO interrupt for the corresponding GPIO (see “ADC Trigger Source” on page 682). 0x5 Timer In addition, the trigger must be enabled with the TnOTE bit in the GPTMCTL register (page 768). 0x6 PWM0 The PWM generator 0 trigger can be configured with the PWM0 Interrupt and Trigger Enable (PWM0INTEN) register (page 1299). 0x7 PWM1 The PWM generator 1 trigger can be configured with the PWM1INTEN register (page 1299). 0x8 PWM2 The PWM generator 2 trigger can be configured with the PWM2INTEN register (page 1299). 0x9 PWM3 The PWM generator 3 trigger can be configured with the PWM3INTEN register (page 1299). 0xA-0xE reserved 0xF Always (continuously sample) 862 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 7:4 EM1 R/W 0x0 Description SS1 Trigger Select This field selects the trigger source for Sample Sequencer 1. The valid configurations for this field are: Value Event 0x0 Processor (default) The trigger is initiated by setting the SSn bit in the ADCPSSI register. 0x1 Analog Comparator 0 This trigger is configured by the Analog Comparator Control 0 (ACCTL0) register (page 1250). 0x2 Analog Comparator 1 This trigger is configured by the Analog Comparator Control 1 (ACCTL1) register (page 1250). 0x3 Analog Comparator 2 This trigger is configured by the Analog Comparator Control 2 (ACCTL2) register (page 1250). 0x4 External (GPIO Pins) This trigger is connected to the GPIO interrupt for the corresponding GPIO (see “ADC Trigger Source” on page 682). 0x5 Timer In addition, the trigger must be enabled with the TnOTE bit in the GPTMCTL register (page 768). 0x6 PWM0 The PWM generator 0 trigger can be configured with the PWM0 Interrupt and Trigger Enable (PWM0INTEN) register (page 1299). 0x7 PWM1 The PWM generator 1 trigger can be configured with the PWM1INTEN register (page 1299). 0x8 PWM2 The PWM generator 2 trigger can be configured with the PWM2INTEN register (page 1299). 0x9 PWM3 The PWM generator 3 trigger can be configured with the PWM3INTEN register (page 1299). 0xA-0xE reserved 0xF Always (continuously sample) November 08, 2011 863 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 3:0 EM0 R/W 0x0 Description SS0 Trigger Select This field selects the trigger source for Sample Sequencer 0 The valid configurations for this field are: Value Event 0x0 Processor (default) The trigger is initiated by setting the SSn bit in the ADCPSSI register. 0x1 Analog Comparator 0 This trigger is configured by the Analog Comparator Control 0 (ACCTL0) register (page 1250). 0x2 Analog Comparator 1 This trigger is configured by the Analog Comparator Control 1 (ACCTL1) register (page 1250). 0x3 Analog Comparator 2 This trigger is configured by the Analog Comparator Control 2 (ACCTL2) register (page 1250). 0x4 External (GPIO Pins) This trigger is connected to the GPIO interrupt for the corresponding GPIO (see “ADC Trigger Source” on page 682). 0x5 Timer In addition, the trigger must be enabled with the TnOTE bit in the GPTMCTL register (page 768). 0x6 PWM0 The PWM generator 0 trigger can be configured with the PWM0 Interrupt and Trigger Enable (PWM0INTEN) register (page 1299). 0x7 PWM1 The PWM generator 1 trigger can be configured with the PWM1INTEN register (page 1299). 0x8 PWM2 The PWM generator 2 trigger can be configured with the PWM2INTEN register (page 1299). 0x9 PWM3 The PWM generator 3 trigger can be configured with the PWM3INTEN register (page 1299). 0xA-0xE reserved 0xF Always (continuously sample) 864 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 7: ADC Underflow Status (ADCUSTAT), offset 0x018 This register indicates underflow conditions in the sample sequencer FIFOs. The corresponding underflow condition is cleared by writing a 1 to the relevant bit position. ADC Underflow Status (ADCUSTAT) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x018 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 UV3 UV2 UV1 UV0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 UV3 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SS3 FIFO Underflow The valid configurations for this field are shown below. This bit is cleared by writing a 1. Value Description 2 UV2 R/W1C 0 1 The FIFO for the Sample Sequencer has hit an underflow condition, meaning that the FIFO is empty and a read was requested. The problematic read does not move the FIFO pointers, and 0s are returned. 0 The FIFO has not underflowed. SS2 FIFO Underflow The valid configurations are the same as those for the UV3 field. This bit is cleared by writing a 1. 1 UV1 R/W1C 0 SS1 FIFO Underflow The valid configurations are the same as those for the UV3 field. This bit is cleared by writing a 1. 0 UV0 R/W1C 0 SS0 FIFO Underflow The valid configurations are the same as those for the UV3 field. This bit is cleared by writing a 1. November 08, 2011 865 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 8: ADC Trigger Source Select (ADCTSSEL), offset 0x01C The ADCTSSEL register specifies which PWM module is selected with the EMn bit field in the ADC Event Multiplexer Select (ADCEMUX) register. The register resets to 0x0000.0000, which selects PWM module 0 for all generators. ADC Trigger Source Select (ADCTSSEL) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x01C Type R/W, reset 0x0000.0000 31 30 29 RO 0 RO 0 RO 0 15 14 13 RO 0 RO 0 RO 0 28 27 26 25 24 23 22 21 RO 0 RO 0 RO 0 R/W 0 R/W 0 RO 0 RO 0 RO 0 12 11 10 9 8 7 6 5 RO 0 RO 0 R/W 0 R/W 0 RO 0 RO 0 RO 0 reserved Type Reset PS3 reserved Type Reset RO 0 20 19 18 17 RO 0 RO 0 RO 0 R/W 0 R/W 0 4 3 2 1 0 RO 0 RO 0 RO 0 R/W 0 reserved PS1 16 PS2 reserved PS0 R/W 0 Bit/Field Name Type Reset Description 31:26 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 25:24 PS3 R/W 0x0 PWM Unit Select This field selects which PWM generator signals are used in the PWM0-PWM3 encodings of the ADCEMUX register EM3 bit field. Value Description 0x0 PWM generator 0 0x1 PWM generator 1 0x2 - 0x3 reserved 23:18 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 17:16 PS2 R/W 0x0 PWM Unit Select This field selects which PWM generator signals are used in the PWM0-PWM3 encodings of the ADCEMUX register EM2 bit field. Value Description 0x0 PWM generator 0 0x1 PWM generator 1 0x2 - 0x3 reserved 15:10 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 866 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 9:8 PS1 R/W 0x0 Description PWM Unit Select This field selects which PWM generator signals are used in the PWM0-PWM3 encodings of the ADCEMUX register EM1 bit field. Value Description 0x0 PWM generator 0 0x1 PWM generator 1 0x2 - 0x3 reserved 7:2 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1:0 PS0 R/W 0x0 PWM Unit Select This field selects which PWM generator signals are used in the PWM0-PWM3 encodings of the ADCEMUX register EM0 bit field. Value Description 0x0 PWM generator 0 0x1 PWM generator 1 0x2 - 0x3 reserved November 08, 2011 867 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 9: ADC Sample Sequencer Priority (ADCSSPRI), offset 0x020 This register sets the priority for each of the sample sequencers. Out of reset, Sequencer 0 has the highest priority, and Sequencer 3 has the lowest priority. When reconfiguring sequence priorities, each sequence must have a unique priority for the ADC to operate properly. ADC Sample Sequencer Priority (ADCSSPRI) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x020 Type R/W, reset 0x0000.3210 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 R/W 1 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 R/W 0 RO 0 RO 0 R/W 0 R/W 1 RO 0 RO 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 RO 0 SS3 R/W 1 reserved RO 0 SS2 R/W 1 Bit/Field Name Type Reset 31:14 reserved RO 0x0000.0 13:12 SS3 R/W 0x3 reserved SS1 reserved SS0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SS3 Priority This field contains a binary-encoded value that specifies the priority encoding of Sample Sequencer 3. A priority encoding of 0x0 is highest and 0x3 is lowest. The priorities assigned to the sequencers must be uniquely mapped. The ADC may not operate properly if two or more fields are equal. 11:10 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 9:8 SS2 R/W 0x2 SS2 Priority This field contains a binary-encoded value that specifies the priority encoding of Sample Sequencer 2. A priority encoding of 0x0 is highest and 0x3 is lowest. The priorities assigned to the sequencers must be uniquely mapped. The ADC may not operate properly if two or more fields are equal. 7:6 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5:4 SS1 R/W 0x1 SS1 Priority This field contains a binary-encoded value that specifies the priority encoding of Sample Sequencer 1. A priority encoding of 0x0 is highest and 0x3 is lowest. The priorities assigned to the sequencers must be uniquely mapped. The ADC may not operate properly if two or more fields are equal. 3:2 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 868 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset Description 1:0 SS0 R/W 0x0 SS0 Priority This field contains a binary-encoded value that specifies the priority encoding of Sample Sequencer 0. A priority encoding of 0x0 is highest and 0x3 is lowest. The priorities assigned to the sequencers must be uniquely mapped. The ADC may not operate properly if two or more fields are equal. November 08, 2011 869 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 10: ADC Sample Phase Control (ADCSPC), offset 0x024 This register allows the ADC module to sample at one of 16 different discrete phases from 0.0° through 337.5°. For example, the sample rate could be effectively doubled by sampling a signal using one ADC module configured with the standard sample time and the second ADC module configured with a 180.0° phase lag. Note: Care should be taken when the PHASE field is non-zero, as the resulting delay in sampling the AINx input may result in undesirable system consequences. The time from ADC trigger to sample is increased and could make the response time longer than anticipated. The added latency could have ramifications in the system design. Designers should carefully consider the impact of this delay. ADC Sample Phase Control (ADCSPC) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 1 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 PHASE RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 870 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 3:0 PHASE R/W 0x0 Description Phase Difference This field selects the sample phase difference from the standard sample time. Value Description 0x0 ADC sample lags by 0.0° 0x1 ADC sample lags by 22.5° 0x2 ADC sample lags by 45.0° 0x3 ADC sample lags by 67.5° 0x4 ADC sample lags by 90.0° 0x5 ADC sample lags by 112.5° 0x6 ADC sample lags by 135.0° 0x7 ADC sample lags by 157.5° 0x8 ADC sample lags by 180.0° 0x9 ADC sample lags by 202.5° 0xA ADC sample lags by 225.0° 0xB ADC sample lags by 247.5° 0xC ADC sample lags by 270.0° 0xD ADC sample lags by 292.5° 0xE ADC sample lags by 315.0° 0xF ADC sample lags by 337.5° November 08, 2011 871 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 11: ADC Processor Sample Sequence Initiate (ADCPSSI), offset 0x028 This register provides a mechanism for application software to initiate sampling in the sample sequencers. Sample sequences can be initiated individually or in any combination. When multiple sequences are triggered simultaneously, the priority encodings in ADCSSPRI dictate execution order. This register also provides a means to configure and then initiate concurrent sampling on all ADC modules. To do this, the first ADC module should be configured. The ADCPSSI register for that module should then be written. The appropriate SS bits should be set along with the SYNCWAIT bit. Additional ADC modules should then be configured following the same procedure. Once the final ADC module is configured, its ADCPSSI register should be written with the appropriate SS bits set along with the GSYNC bit. All of the ADC modules then begin concurrent sampling according to their configuration. ADC Processor Sample Sequence Initiate (ADCPSSI) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x028 Type R/W, reset 31 30 GSYNC Type Reset 29 28 reserved 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 reserved SYNCWAIT R/W 0 RO 0 RO 0 RO 0 R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31 GSYNC R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 SS3 SS2 SS1 SS0 WO - WO - WO - WO - Description Global Synchronize Value Description 30:28 reserved RO 0x0 27 SYNCWAIT R/W 0 1 This bit initiates sampling in multiple ADC modules at the same time. Any ADC module that has been initialized by setting an SSn bit and the SYNCWAIT bit starts sampling once this bit is written. 0 This bit is cleared once sampling has been initiated. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Synchronize Wait Value Description 26:4 reserved RO 0x0000.0 1 This bit allows the sample sequences to be initiated, but delays sampling until the GSYNC bit is set. 0 Sampling begins when a sample sequence has been initiated. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 872 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset Description 3 SS3 WO - SS3 Initiate Value Description 1 Begin sampling on Sample Sequencer 3, if the sequencer is enabled in the ADCACTSS register. 0 No effect. Only a write by software is valid; a read of this register returns no meaningful data. 2 SS2 WO - SS2 Initiate Value Description 1 Begin sampling on Sample Sequencer 2, if the sequencer is enabled in the ADCACTSS register. 0 No effect. Only a write by software is valid; a read of this register returns no meaningful data. 1 SS1 WO - SS1 Initiate Value Description 1 Begin sampling on Sample Sequencer 1, if the sequencer is enabled in the ADCACTSS register. 0 No effect. Only a write by software is valid; a read of this register returns no meaningful data. 0 SS0 WO - SS0 Initiate Value Description 1 Begin sampling on Sample Sequencer 0, if the sequencer is enabled in the ADCACTSS register. 0 No effect. Only a write by software is valid; a read of this register returns no meaningful data. November 08, 2011 873 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 12: ADC Sample Averaging Control (ADCSAC), offset 0x030 This register controls the amount of hardware averaging applied to conversion results. The final conversion result stored in the FIFO is averaged from 2 AVG consecutive ADC samples at the specified ADC speed. If AVG is 0, the sample is passed directly through without any averaging. If AVG=6, then 64 consecutive ADC samples are averaged to generate one result in the sequencer FIFO. An AVG=7 provides unpredictable results. ADC Sample Averaging Control (ADCSAC) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x030 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:3 reserved RO 0x0000.000 2:0 AVG R/W 0x0 AVG R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Hardware Averaging Control Specifies the amount of hardware averaging that will be applied to ADC samples. The AVG field can be any value between 0 and 6. Entering a value of 7 creates unpredictable results. Value Description 0x0 No hardware oversampling 0x1 2x hardware oversampling 0x2 4x hardware oversampling 0x3 8x hardware oversampling 0x4 16x hardware oversampling 0x5 32x hardware oversampling 0x6 64x hardware oversampling 0x7 reserved 874 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 13: ADC Digital Comparator Interrupt Status and Clear (ADCDCISC), offset 0x034 This register provides status and acknowledgement of digital comparator interrupts. One bit is provided for each comparator. ADC Digital Comparator Interrupt Status and Clear (ADCDCISC) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x034 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 DCINT7 R/W1C 0 RO 0 RO 0 7 6 5 4 3 2 1 0 DCINT7 DCINT6 DCINT5 DCINT4 DCINT3 DCINT2 DCINT1 DCINT0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Digital Comparator 7 Interrupt Status and Clear Value Description 1 Digital Comparator 7 has generated an interrupt. 0 No interrupt. This bit is cleared by writing a 1. 6 DCINT6 R/W1C 0 Digital Comparator 6 Interrupt Status and Clear Value Description 1 Digital Comparator 6 has generated an interrupt. 0 No interrupt. This bit is cleared by writing a 1. 5 DCINT5 R/W1C 0 Digital Comparator 5 Interrupt Status and Clear Value Description 1 Digital Comparator 5 has generated an interrupt. 0 No interrupt. This bit is cleared by writing a 1. November 08, 2011 875 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 4 DCINT4 R/W1C 0 Description Digital Comparator 4 Interrupt Status and Clear Value Description 1 Digital Comparator 4 has generated an interrupt. 0 No interrupt. This bit is cleared by writing a 1. 3 DCINT3 R/W1C 0 Digital Comparator 3 Interrupt Status and Clear Value Description 1 Digital Comparator 3 has generated an interrupt. 0 No interrupt. This bit is cleared by writing a 1. 2 DCINT2 R/W1C 0 Digital Comparator 2 Interrupt Status and Clear Value Description 1 Digital Comparator 2 has generated an interrupt. 0 No interrupt. This bit is cleared by writing a 1. 1 DCINT1 R/W1C 0 Digital Comparator 1 Interrupt Status and Clear Value Description 1 Digital Comparator 1 has generated an interrupt. 0 No interrupt. This bit is cleared by writing a 1. 0 DCINT0 R/W1C 0 Digital Comparator 0 Interrupt Status and Clear Value Description 1 Digital Comparator 0 has generated an interrupt. 0 No interrupt. This bit is cleared by writing a 1. 876 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 14: ADC Control (ADCCTL), offset 0x038 This register configures the voltage reference. The voltage references for the conversion can be VDDA and GNDA or VREFA+ and VREFA-. ADC Control (ADCCTL) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x038 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1:0 VREF R/W 0x0 VREF R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Voltage Reference Select Value Description 0x0 VDDA and GNDA are the voltage references. 0x1 - 0x3 The external VREFA+ and VREFA- inputs are the voltage references. November 08, 2011 877 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 15: ADC Sample Sequence Input Multiplexer Select 0 (ADCSSMUX0), offset 0x040 This register, along with the ADCSSEMUX0 register, defines the analog input configuration for each sample in a sequence executed with Sample Sequencer 0. If the corresponding EMUXn bit in the ADCSSEMUX0 register is set, the MUXn field in this register selects from AIN[23:16]. When the corresponding EMUXn bit is clear, the MUXn field selects from AIN[15:0]. This register is 32 bits wide and contains information for eight possible samples. Note: Channels AIN[31:24] do not exist on this microcontroller. Configuring MUXn to be 0x8-0xF when the corresponding EMUXn bit is set results in undefined behavior. ADC Sample Sequence Input Multiplexer Select 0 (ADCSSMUX0) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x040 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 R/W 0 25 24 23 22 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 MUX7 Type Reset 20 19 18 R/W 0 R/W 0 R/W 0 R/W 0 7 6 5 4 R/W 0 R/W 0 R/W 0 R/W 0 MUX6 MUX3 Type Reset 21 17 16 R/W 0 R/W 0 R/W 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 MUX5 MUX2 MUX4 MUX1 Bit/Field Name Type Reset 31:28 MUX7 R/W 0x0 MUX0 Description 8th Sample Input Select The MUX7 field is used during the eighth sample of a sequence executed with the sample sequencer. It specifies which of the analog inputs is sampled for the analog-to-digital conversion. The value set here indicates the corresponding pin, for example, a value of 0x1 when EMUX7 is clear indicates the input is AIN1. A value of 0x1 when EMUX7 is set indicates the input is AIN17. If differential sampling is enabled (the D7 bit in the ADCSSCTL0 register is set), this field must be set to the pair number "i", where the paired inputs are "2i and 2i+1". 27:24 MUX6 R/W 0x0 7th Sample Input Select The MUX6 field is used during the seventh sample of a sequence executed with the sample sequencer. It specifies which of the analog inputs is sampled for the analog-to-digital conversion. 23:20 MUX5 R/W 0x0 6th Sample Input Select The MUX5 field is used during the sixth sample of a sequence executed with the sample sequencer. It specifies which of the analog inputs is sampled for the analog-to-digital conversion. 19:16 MUX4 R/W 0x0 5th Sample Input Select The MUX4 field is used during the fifth sample of a sequence executed with the sample sequencer. It specifies which of the analog inputs is sampled for the analog-to-digital conversion. 878 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 15:12 MUX3 R/W 0x0 Description 4th Sample Input Select The MUX3 field is used during the fourth sample of a sequence executed with the sample sequencer. It specifies which of the analog inputs is sampled for the analog-to-digital conversion. 11:8 MUX2 R/W 0x0 3rd Sample Input Select The MUX2 field is used during the third sample of a sequence executed with the sample sequencer. It specifies which of the analog inputs is sampled for the analog-to-digital conversion. 7:4 MUX1 R/W 0x0 2nd Sample Input Select The MUX1 field is used during the second sample of a sequence executed with the sample sequencer. It specifies which of the analog inputs is sampled for the analog-to-digital conversion. 3:0 MUX0 R/W 0x0 1st Sample Input Select The MUX0 field is used during the first sample of a sequence executed with the sample sequencer. It specifies which of the analog inputs is sampled for the analog-to-digital conversion. November 08, 2011 879 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 16: ADC Sample Sequence Control 0 (ADCSSCTL0), offset 0x044 This register contains the configuration information for each sample for a sequence executed with a sample sequencer. When configuring a sample sequence, the END bit must be set for the final sample, whether it be after the first sample, eighth sample, or any sample in between. This register is 32 bits wide and contains information for eight possible samples. ADC Sample Sequence Control 0 (ADCSSCTL0) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x044 Type R/W, reset 0x0000.0000 31 Type Reset Type Reset 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 TS7 IE7 END7 D7 TS6 IE6 END6 D6 TS5 IE5 END5 D5 TS4 IE4 END4 D4 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TS3 IE3 END3 D3 TS2 IE2 END2 D2 TS1 IE1 END1 D1 TS0 IE0 END0 D0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31 TS7 R/W 0 Description 8th Sample Temp Sensor Select Value Description 30 IE7 R/W 0 1 The temperature sensor is read during the eighth sample of the sample sequence. 0 The input pin specified by the ADCSSMUXn register is read during the eighth sample of the sample sequence. 8th Sample Interrupt Enable Value Description 1 The raw interrupt signal (INR0 bit) is asserted at the end of the eighth sample's conversion. If the MASK0 bit in the ADCIM register is set, the interrupt is promoted to the interrupt controller. 0 The raw interrupt is not asserted to the interrupt controller. It is legal to have multiple samples within a sequence generate interrupts. 29 END7 R/W 0 8th Sample is End of Sequence Value Description 1 The eighth sample is the last sample of the sequence. 0 Another sample in the sequence is the final sample. It is possible to end the sequence on any sample position. Software must set an ENDn bit somewhere within the sequence. Samples defined after the sample containing a set ENDn bit are not requested for conversion even though the fields may be non-zero. 880 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 28 D7 R/W 0 Description 8th Sample Diff Input Select Value Description 1 The analog input is differentially sampled. The corresponding ADCSSMUXn nibble must be set to the pair number "i", where the paired inputs are "2i and 2i+1". 0 The analog inputs are not differentially sampled. Because the temperature sensor does not have a differential option, this bit must not be set when the TS7 bit is set. 27 TS6 R/W 0 7th Sample Temp Sensor Select Same definition as TS7 but used during the seventh sample. 26 IE6 R/W 0 7th Sample Interrupt Enable Same definition as IE7 but used during the seventh sample. 25 END6 R/W 0 7th Sample is End of Sequence Same definition as END7 but used during the seventh sample. 24 D6 R/W 0 7th Sample Diff Input Select Same definition as D7 but used during the seventh sample. 23 TS5 R/W 0 6th Sample Temp Sensor Select Same definition as TS7 but used during the sixth sample. 22 IE5 R/W 0 6th Sample Interrupt Enable Same definition as IE7 but used during the sixth sample. 21 END5 R/W 0 6th Sample is End of Sequence Same definition as END7 but used during the sixth sample. 20 D5 R/W 0 6th Sample Diff Input Select Same definition as D7 but used during the sixth sample. 19 TS4 R/W 0 5th Sample Temp Sensor Select Same definition as TS7 but used during the fifth sample. 18 IE4 R/W 0 5th Sample Interrupt Enable Same definition as IE7 but used during the fifth sample. 17 END4 R/W 0 5th Sample is End of Sequence Same definition as END7 but used during the fifth sample. 16 D4 R/W 0 5th Sample Diff Input Select Same definition as D7 but used during the fifth sample. 15 TS3 R/W 0 4th Sample Temp Sensor Select Same definition as TS7 but used during the fourth sample. 14 IE3 R/W 0 4th Sample Interrupt Enable Same definition as IE7 but used during the fourth sample. November 08, 2011 881 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 13 END3 R/W 0 Description 4th Sample is End of Sequence Same definition as END7 but used during the fourth sample. 12 D3 R/W 0 4th Sample Diff Input Select Same definition as D7 but used during the fourth sample. 11 TS2 R/W 0 3rd Sample Temp Sensor Select Same definition as TS7 but used during the third sample. 10 IE2 R/W 0 3rd Sample Interrupt Enable Same definition as IE7 but used during the third sample. 9 END2 R/W 0 3rd Sample is End of Sequence Same definition as END7 but used during the third sample. 8 D2 R/W 0 3rd Sample Diff Input Select Same definition as D7 but used during the third sample. 7 TS1 R/W 0 2nd Sample Temp Sensor Select Same definition as TS7 but used during the second sample. 6 IE1 R/W 0 2nd Sample Interrupt Enable Same definition as IE7 but used during the second sample. 5 END1 R/W 0 2nd Sample is End of Sequence Same definition as END7 but used during the second sample. 4 D1 R/W 0 2nd Sample Diff Input Select Same definition as D7 but used during the second sample. 3 TS0 R/W 0 1st Sample Temp Sensor Select Same definition as TS7 but used during the first sample. 2 IE0 R/W 0 1st Sample Interrupt Enable Same definition as IE7 but used during the first sample. 1 END0 R/W 0 1st Sample is End of Sequence Same definition as END7 but used during the first sample. 0 D0 R/W 0 1st Sample Diff Input Select Same definition as D7 but used during the first sample. 882 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 17: ADC Sample Sequence Result FIFO 0 (ADCSSFIFO0), offset 0x048 Register 18: ADC Sample Sequence Result FIFO 1 (ADCSSFIFO1), offset 0x068 Register 19: ADC Sample Sequence Result FIFO 2 (ADCSSFIFO2), offset 0x088 Register 20: ADC Sample Sequence Result FIFO 3 (ADCSSFIFO3), offset 0x0A8 Important: This register is read-sensitive. See the register description for details. This register contains the conversion results for samples collected with the sample sequencer (the ADCSSFIFO0 register is used for Sample Sequencer 0, ADCSSFIFO1 for Sequencer 1, ADCSSFIFO2 for Sequencer 2, and ADCSSFIFO3 for Sequencer 3). Reads of this register return conversion result data in the order sample 0, sample 1, and so on, until the FIFO is empty. If the FIFO is not properly handled by software, overflow and underflow conditions are registered in the ADCOSTAT and ADCUSTAT registers. ADC Sample Sequence Result FIFO n (ADCSSFIFOn) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x048 Type RO, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 5 4 3 2 1 0 RO - RO - RO - RO - RO - RO - reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 reserved Type Reset RO 0 RO 0 DATA RO 0 RO 0 RO - RO - RO - Bit/Field Name Type Reset 31:12 reserved RO 0x0000.0 11:0 DATA RO - RO - RO - RO - Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Conversion Result Data November 08, 2011 883 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 21: ADC Sample Sequence FIFO 0 Status (ADCSSFSTAT0), offset 0x04C Register 22: ADC Sample Sequence FIFO 1 Status (ADCSSFSTAT1), offset 0x06C Register 23: ADC Sample Sequence FIFO 2 Status (ADCSSFSTAT2), offset 0x08C Register 24: ADC Sample Sequence FIFO 3 Status (ADCSSFSTAT3), offset 0x0AC This register provides a window into the sample sequencer, providing full/empty status information as well as the positions of the head and tail pointers. The reset value of 0x100 indicates an empty FIFO with the head and tail pointers both pointing to index 0. The ADCSSFSTAT0 register provides status on FIFO0, which has 8 entries; ADCSSFSTAT1 on FIFO1, which has 4 entries; ADCSSFSTAT2 on FIFO2, which has 4 entries; and ADCSSFSTAT3 on FIFO3 which has a single entry. ADC Sample Sequence FIFO 0 Status (ADCSSFSTAT0) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x04C Type RO, reset 0x0000.0100 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 RO 0 FULL RO 0 RO 0 reserved RO 0 RO 0 EMPTY RO 0 Bit/Field Name Type Reset 31:13 reserved RO 0x0000.0 12 FULL RO 0 RO 1 HPTR TPTR Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. FIFO Full Value Description 11:9 reserved RO 0x0 8 EMPTY RO 1 1 The FIFO is currently full. 0 The FIFO is not currently full. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. FIFO Empty Value Description 1 The FIFO is currently empty. 0 The FIFO is not currently empty. 884 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 7:4 HPTR RO 0x0 Description FIFO Head Pointer This field contains the current "head" pointer index for the FIFO, that is, the next entry to be written. Valid values are 0x0-0x7 for FIFO0; 0x0-0x3 for FIFO1 and FIFO2; and 0x0 for FIFO3. 3:0 TPTR RO 0x0 FIFO Tail Pointer This field contains the current "tail" pointer index for the FIFO, that is, the next entry to be read. Valid values are 0x0-0x7 for FIFO0; 0x0-0x3 for FIFO1 and FIFO2; and 0x0 for FIFO3. November 08, 2011 885 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 25: ADC Sample Sequence 0 Operation (ADCSSOP0), offset 0x050 This register determines whether the sample from the given conversion on Sample Sequence 0 is saved in the Sample Sequence FIFO0 or sent to the digital comparator unit. ADC Sample Sequence 0 Operation (ADCSSOP0) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x050 Type R/W, reset 0x0000.0000 31 30 29 reserved Type Reset 27 S7DCOP 26 25 reserved 24 23 S6DCOP 22 21 reserved 20 19 S5DCOP 18 17 reserved 16 S4DCOP RO 0 RO 0 RO 0 R/W 0 RO 0 RO 0 RO 0 R/W 0 RO 0 RO 0 RO 0 R/W 0 RO 0 RO 0 RO 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 reserved Type Reset 28 RO 0 RO 0 S3DCOP RO 0 R/W 0 reserved RO 0 RO 0 S2DCOP RO 0 Bit/Field Name Type Reset 31:29 reserved RO 0x0 28 S7DCOP R/W 0 R/W 0 reserved RO 0 RO 0 S1DCOP RO 0 R/W 0 reserved RO 0 RO 0 S0DCOP RO 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 7 Digital Comparator Operation Value Description 27:25 reserved RO 0x0 24 S6DCOP R/W 0 1 The eighth sample is sent to the digital comparator unit specified by the S7DCSEL bit in the ADCSSDC0 register, and the value is not written to the FIFO. 0 The eighth sample is saved in Sample Sequence FIFO0. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 6 Digital Comparator Operation Same definition as S7DCOP but used during the seventh sample. 23:21 reserved RO 0x0 20 S5DCOP R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 5 Digital Comparator Operation Same definition as S7DCOP but used during the sixth sample. 19:17 reserved RO 0x0 16 S4DCOP R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 4 Digital Comparator Operation Same definition as S7DCOP but used during the fifth sample. 15:13 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 886 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 12 S3DCOP R/W 0 Description Sample 3 Digital Comparator Operation Same definition as S7DCOP but used during the fourth sample. 11:9 reserved RO 0x0 8 S2DCOP R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 2 Digital Comparator Operation Same definition as S7DCOP but used during the third sample. 7:5 reserved RO 0x0 4 S1DCOP R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 1 Digital Comparator Operation Same definition as S7DCOP but used during the second sample. 3:1 reserved RO 0x0 0 S0DCOP R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 0 Digital Comparator Operation Same definition as S7DCOP but used during the first sample. November 08, 2011 887 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 26: ADC Sample Sequence 0 Digital Comparator Select (ADCSSDC0), offset 0x054 This register determines which digital comparator receives the sample from the given conversion on Sample Sequence 0, if the corresponding SnDCOP bit in the ADCSSOP0 register is set. ADC Sample Sequence 0 Digital Comparator Select (ADCSSDC0) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x054 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 S7DCSEL Type Reset 24 23 22 21 20 19 S5DCSEL 18 17 16 S4DCSEL R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 S3DCSEL Type Reset 25 S6DCSEL R/W 0 R/W 0 S2DCSEL R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:28 S7DCSEL R/W 0x0 S1DCSEL R/W 0 R/W 0 R/W 0 R/W 0 S0DCSEL R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Sample 7 Digital Comparator Select When the S7DCOP bit in the ADCSSOP0 register is set, this field indicates which digital comparator unit (and its associated set of control registers) receives the eighth sample from Sample Sequencer 0. Note: Values not listed are reserved. Value Description 27:24 S6DCSEL R/W 0x0 0x0 Digital Comparator Unit 0 (ADCDCCMP0 and ADCDCCTL0) 0x1 Digital Comparator Unit 1 (ADCDCCMP1 and ADCDCCTL1) 0x2 Digital Comparator Unit 2 (ADCDCCMP2 and ADCDCCTL2) 0x3 Digital Comparator Unit 3 (ADCDCCMP3 and ADCDCCTL3) 0x4 Digital Comparator Unit 4 (ADCDCCMP4 and ADCDCCTL4) 0x5 Digital Comparator Unit 5 (ADCDCCMP5 and ADCDCCTL5) 0x6 Digital Comparator Unit 6 (ADCDCCMP6 and ADCDCCTL6) 0x7 Digital Comparator Unit 7 (ADCDCCMP7 and ADCDCCTL7) Sample 6 Digital Comparator Select This field has the same encodings as S7DCSEL but is used during the seventh sample. 23:20 S5DCSEL R/W 0x0 Sample 5 Digital Comparator Select This field has the same encodings as S7DCSEL but is used during the sixth sample. 19:16 S4DCSEL R/W 0x0 Sample 4 Digital Comparator Select This field has the same encodings as S7DCSEL but is used during the fifth sample. 15:12 S3DCSEL R/W 0x0 Sample 3 Digital Comparator Select This field has the same encodings as S7DCSEL but is used during the fourth sample. 888 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 11:8 S2DCSEL R/W 0x0 Description Sample 2 Digital Comparator Select This field has the same encodings as S7DCSEL but is used during the third sample. 7:4 S1DCSEL R/W 0x0 Sample 1 Digital Comparator Select This field has the same encodings as S7DCSEL but is used during the second sample. 3:0 S0DCSEL R/W 0x0 Sample 0 Digital Comparator Select This field has the same encodings as S7DCSEL but is used during the first sample. November 08, 2011 889 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 27: ADC Sample Sequence Extended Input Multiplexer Select 0 (ADCSSEMUX0), offset 0x058 This register, along with the ADCSSMUX0 register, defines the analog input configuration for each sample in a sequence executed with Sample Sequencer 0. If a bit in this register is set, the corresponding MUXn field in the ADCSSMUX0 register selects from AIN[23:16]. When a bit in this register is clear, the corresponding MUXn field selects from AIN[15:0]. This register is 32 bits wide and contains information for eight possible samples. Note that this register is not used when the differential channel designation is used (the Dn bit is set in the ADCSSCTL0 register) because the ADCSSMUX0 register can select all the available pairs. ADC Sample Sequence Extended Input Multiplexer Select 0 (ADCSSEMUX0) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x058 Type R/W, reset 0x0000.0000 31 30 29 reserved Type Reset 27 EMUX7 26 25 reserved 24 23 EMUX6 22 21 reserved 20 19 EMUX5 18 17 reserved 16 EMUX4 RO 0 RO 0 RO 0 R/W 0 RO 0 RO 0 RO 0 R/W 0 RO 0 RO 0 RO 0 R/W 0 RO 0 RO 0 RO 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 reserved Type Reset 28 RO 0 RO 0 EMUX3 RO 0 R/W 0 reserved RO 0 RO 0 EMUX2 RO 0 R/W 0 reserved RO 0 RO 0 EMUX1 RO 0 R/W 0 reserved RO 0 RO 0 EMUX0 RO 0 R/W 0 Bit/Field Name Type Reset Description 31:29 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 28 EMUX7 R/W 0x0 8th Sample Input Select (Upper Bit) The EMUX7 field is used during the eighth sample of a sequence executed with the sample sequencer. Value Description 1 The eighth sample input is selected from AIN[23:16] using the ADCSSMUX0 register. For example, if the MUX7 field is 0x0, AIN16 is selected. 0 The eighth sample input is selected from AIN[15:0] using the ADCSSMUX0 register. For example, if the MUX7 field is 0x0, AIN0 is selected. 27:25 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 24 EMUX6 R/W 0x0 7th Sample Input Select (Upper Bit) The EMUX6 field is used during the seventh sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX7. 23:21 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 890 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 20 EMUX5 R/W 0x0 Description 6th Sample Input Select (Upper Bit) The EMUX5 field is used during the sixth sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX7. 19:17 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 16 EMUX4 R/W 0x0 5th Sample Input Select (Upper Bit) The EMUX4 field is used during the fifth sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX7. 15:13 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 12 EMUX3 R/W 0x0 4th Sample Input Select (Upper Bit) The EMUX3 field is used during the fourth sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX7. 11:9 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 8 EMUX2 R/W 0x0 3rd Sample Input Select (Upper Bit) The EMUX2 field is used during the third sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX7. 7:5 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 EMUX1 R/W 0x0 2th Sample Input Select (Upper Bit) The EMUX1 field is used during the second sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX7. 3:1 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 EMUX0 R/W 0x0 1st Sample Input Select (Upper Bit) The EMUX0 field is used during the first sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX7. November 08, 2011 891 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 28: ADC Sample Sequence Input Multiplexer Select 1 (ADCSSMUX1), offset 0x060 Register 29: ADC Sample Sequence Input Multiplexer Select 2 (ADCSSMUX2), offset 0x080 This register, along with the ADCSSEMUX1 or ADCSSEMUX2 register, defines the analog input configuration for each sample in a sequence executed with Sample Sequencer 1 or 2. If the corresponding EMUXn bit in the ADCSSEMUX1 or ADCSSEMUX2 register is set, the MUXn field in this register selects from AIN[23:16]. When the corresponding EMUXn bit is clear, the MUXn field selects from AIN[15:0]. These registers are 16 bits wide and contain information for four possible samples. See the ADCSSMUX0 register on page 878 for detailed bit descriptions. The ADCSSMUX1 register affects Sample Sequencer 1 and the ADCSSMUX2 register affects Sample Sequencer 2. Note: Channels AIN[31:24] do not exist on this microcontroller. Configuring MUXn to be 0x8-0xF when the corresponding EMUXn bit is set results in undefined behavior. ADC Sample Sequence Input Multiplexer Select 1 (ADCSSMUX1) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x060 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 5 4 3 2 1 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 15 14 RO 0 RO 0 RO 0 RO 0 13 12 11 10 MUX3 Type Reset R/W 0 R/W 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 MUX2 R/W 0 R/W 0 R/W 0 R/W 0 MUX1 R/W 0 R/W 0 R/W 0 R/W 0 MUX0 R/W 0 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15:12 MUX3 R/W 0x0 4th Sample Input Select 11:8 MUX2 R/W 0x0 3rd Sample Input Select 7:4 MUX1 R/W 0x0 2nd Sample Input Select 3:0 MUX0 R/W 0x0 1st Sample Input Select R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 892 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 30: ADC Sample Sequence Control 1 (ADCSSCTL1), offset 0x064 Register 31: ADC Sample Sequence Control 2 (ADCSSCTL2), offset 0x084 These registers contain the configuration information for each sample for a sequence executed with Sample Sequencer 1 or 2. When configuring a sample sequence, the END bit must be set for the final sample, whether it be after the first sample, fourth sample, or any sample in between. These registers are 16-bits wide and contain information for four possible samples. See the ADCSSCTL0 register on page 880 for detailed bit descriptions. The ADCSSCTL1 register configures Sample Sequencer 1 and the ADCSSCTL2 register configures Sample Sequencer 2. ADC Sample Sequence Control 1 (ADCSSCTL1) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x064 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 TS3 IE3 END3 D3 TS2 IE2 END2 D2 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 TS1 IE1 END1 D1 TS0 IE0 END0 D0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset Type Reset Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15 TS3 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4th Sample Temp Sensor Select Same definition as TS7 but used during the fourth sample. 14 IE3 R/W 0 4th Sample Interrupt Enable Same definition as IE7 but used during the fourth sample. 13 END3 R/W 0 4th Sample is End of Sequence Same definition as END7 but used during the fourth sample. 12 D3 R/W 0 4th Sample Diff Input Select Same definition as D7 but used during the fourth sample. 11 TS2 R/W 0 3rd Sample Temp Sensor Select Same definition as TS7 but used during the third sample. 10 IE2 R/W 0 3rd Sample Interrupt Enable Same definition as IE7 but used during the third sample. 9 END2 R/W 0 3rd Sample is End of Sequence Same definition as END7 but used during the third sample. 8 D2 R/W 0 3rd Sample Diff Input Select Same definition as D7 but used during the third sample. November 08, 2011 893 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 7 TS1 R/W 0 Description 2nd Sample Temp Sensor Select Same definition as TS7 but used during the second sample. 6 IE1 R/W 0 2nd Sample Interrupt Enable Same definition as IE7 but used during the second sample. 5 END1 R/W 0 2nd Sample is End of Sequence Same definition as END7 but used during the second sample. 4 D1 R/W 0 2nd Sample Diff Input Select Same definition as D7 but used during the second sample. 3 TS0 R/W 0 1st Sample Temp Sensor Select Same definition as TS7 but used during the first sample. 2 IE0 R/W 0 1st Sample Interrupt Enable Same definition as IE7 but used during the first sample. 1 END0 R/W 0 1st Sample is End of Sequence Same definition as END7 but used during the first sample. 0 D0 R/W 0 1st Sample Diff Input Select Same definition as D7 but used during the first sample. 894 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 32: ADC Sample Sequence 1 Operation (ADCSSOP1), offset 0x070 Register 33: ADC Sample Sequence 2 Operation (ADCSSOP2), offset 0x090 This register determines whether the sample from the given conversion on Sample Sequence n is saved in the Sample Sequence n FIFO or sent to the digital comparator unit. The ADCSSOP1 register controls Sample Sequencer 1 and the ADCSSOP2 register controls Sample Sequencer 2. ADC Sample Sequence 1 Operation (ADCSSOP1) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x070 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved Type Reset reserved Type Reset RO 0 RO 0 S3DCOP RO 0 R/W 0 reserved RO 0 RO 0 S2DCOP RO 0 Bit/Field Name Type Reset 31:13 reserved RO 0x0000.0 12 S3DCOP R/W 0 R/W 0 reserved RO 0 RO 0 S1DCOP RO 0 R/W 0 reserved RO 0 RO 0 S0DCOP RO 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 3 Digital Comparator Operation Value Description 11:9 reserved RO 0x0 8 S2DCOP R/W 0 1 The fourth sample is sent to the digital comparator unit specified by the S3DCSEL bit in the ADCSSDC0n register, and the value is not written to the FIFO. 0 The fourth sample is saved in Sample Sequence FIFOn. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 2 Digital Comparator Operation Same definition as S3DCOP but used during the third sample. 7:5 reserved RO 0x0 4 S1DCOP R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 1 Digital Comparator Operation Same definition as S3DCOP but used during the second sample. 3:1 reserved RO 0x0 0 S0DCOP R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 0 Digital Comparator Operation Same definition as S3DCOP but used during the first sample. November 08, 2011 895 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 34: ADC Sample Sequence 1 Digital Comparator Select (ADCSSDC1), offset 0x074 Register 35: ADC Sample Sequence 2 Digital Comparator Select (ADCSSDC2), offset 0x094 These registers determine which digital comparator receives the sample from the given conversion on Sample Sequence n if the corresponding SnDCOP bit in the ADCSSOPn register is set. The ADCSSDC1 register controls the selection for Sample Sequencer 1 and the ADCSSDC2 register controls the selection for Sample Sequencer 2. ADC Sample Sequence 1 Digital Comparator Select (ADCSSDC1) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x074 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset S3DCSEL Type Reset S2DCSEL R/W 0 R/W 0 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15:12 S3DCSEL R/W 0x0 S1DCSEL R/W 0 S0DCSEL R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 3 Digital Comparator Select When the S3DCOP bit in the ADCSSOPn register is set, this field indicates which digital comparator unit (and its associated set of control registers) receives the eighth sample from Sample Sequencer n. Note: Values not listed are reserved. Value Description 11:8 S2DCSEL R/W 0x0 0x0 Digital Comparator Unit 0 (ADCDCCMP0 and ADCCCTL0) 0x1 Digital Comparator Unit 1 (ADCDCCMP1 and ADCCCTL1) 0x2 Digital Comparator Unit 2 (ADCDCCMP2 and ADCCCTL2) 0x3 Digital Comparator Unit 3 (ADCDCCMP3 and ADCCCTL3) 0x4 Digital Comparator Unit 4 (ADCDCCMP4 and ADCCCTL4) 0x5 Digital Comparator Unit 5 (ADCDCCMP5 and ADCCCTL5) 0x6 Digital Comparator Unit 6 (ADCDCCMP6 and ADCCCTL6) 0x7 Digital Comparator Unit 7 (ADCDCCMP7 and ADCCCTL7) Sample 2 Digital Comparator Select This field has the same encodings as S3DCSEL but is used during the third sample. 896 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 7:4 S1DCSEL R/W 0x0 Description Sample 1 Digital Comparator Select This field has the same encodings as S3DCSEL but is used during the second sample. 3:0 S0DCSEL R/W 0x0 Sample 0 Digital Comparator Select This field has the same encodings as S3DCSEL but is used during the first sample. November 08, 2011 897 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 36: ADC Sample Sequence Extended Input Multiplexer Select 1 (ADCSSEMUX1), offset 0x078 Register 37: ADC Sample Sequence Extended Input Multiplexer Select 2 (ADCSSEMUX2), offset 0x098 This register, along with the ADCSSMUX1 or ADCSSMUX2 register, defines the analog input configuration for each sample in a sequence executed with either Sample Sequencer 1 or 2. If a bit in this register is set, the corresponding MUXn field in the ADCSSMUX1 or ADCSSMUX2 register selects from AIN[23:16]. When a bit in this register is clear, the corresponding MUXn field selects from AIN[15:0]. This register is 16 bits wide and contains information for four possible samples. The ADCSSEMUX1 register controls Sample Sequencer 1 and the ADCSSEMUX2 register controls Sample Sequencer 2. Note that this register is not used when the differential channel designation is used (the Dn bit is set in the ADCSSCTL1 or ADCSSCTL2 register) because the ADCSSMUX1 or ADCSSMUX2 register can select all the available pairs. ADC Sample Sequence Extended Input Multiplexer Select 1 (ADCSSEMUX1) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x078 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 6 5 4 3 2 1 reserved Type Reset RO 0 15 RO 0 RO 0 14 13 reserved Type Reset RO 0 RO 0 RO 0 RO 0 12 11 EMUX3 RO 0 R/W 0 RO 0 RO 0 10 9 reserved RO 0 RO 0 RO 0 RO 0 8 7 EMUX2 RO 0 Bit/Field Name Type Reset 31:13 reserved RO 0x0000 12 EMUX3 R/W 0x0 R/W 0 reserved RO 0 RO 0 EMUX1 RO 0 R/W 0 reserved RO 0 RO 0 0 EMUX0 RO 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4th Sample Input Select (Upper Bit) The EMUX3 field is used during the fourth sample of a sequence executed with the sample sequencer. Value Description 11:9 reserved RO 0x0 1 The fourth sample input is selected from AIN[23:16] using the ADCSSMUX1 or ADCSSMUX2 register. For example, if the MUX3 field is 0x0, AIN16 is selected. 0 The fourth sample input is selected from AIN[15:0] using the ADCSSMUX1 or ADCSSMUX2 register. For example, if the MUX3 field is 0x0, AIN0 is selected. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 898 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 8 EMUX2 R/W 0x0 Description 3rd Sample Input Select (Upper Bit) The EMUX2 field is used during the third sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX3. 7:5 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 EMUX1 R/W 0x0 2th Sample Input Select (Upper Bit) The EMUX1 field is used during the second sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX3. 3:1 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 EMUX0 R/W 0x0 1st Sample Input Select (Upper Bit) The EMUX0 field is used during the first sample of a sequence executed with the sample sequencer. This bit has the same description as EMUX3. November 08, 2011 899 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 38: ADC Sample Sequence Input Multiplexer Select 3 (ADCSSMUX3), offset 0x0A0 This register, along with the ADCSSEMUX3 register, defines the analog input configuration for the sample in a sequence executed with Sample Sequencer 3. If the EMUX0 bit in the ADCSSEMUX3 register is set, the MUX0 field in this register selects from AIN[23:16]. When the EMUX0 bit is clear, the MUX0 field selects from AIN[15:0]. This register is four bits wide and contains information for one possible sample. See the ADCSSMUX0 register on page 878 for detailed bit descriptions. ADC Sample Sequence Input Multiplexer Select 3 (ADCSSMUX3) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x0A0 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 1 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 MUX0 RO 0 Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3:0 MUX0 R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1st Sample Input Select 900 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 39: ADC Sample Sequence Control 3 (ADCSSCTL3), offset 0x0A4 This register contains the configuration information for a sample executed with Sample Sequencer 3. The END0 bit is always set as this sequencer can execute only one sample. This register is 4 bits wide and contains information for one possible sample. See the ADCSSCTL0 register on page 880 for detailed bit descriptions. ADC Sample Sequence Control 3 (ADCSSCTL3) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x0A4 Type R/W, reset 0x0000.0002 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 TS0 IE0 END0 D0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 1 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 TS0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1st Sample Temp Sensor Select Same definition as TS7 but used during the first sample. 2 IE0 R/W 0 1st Sample Interrupt Enable Same definition as IE7 but used during the first sample. 1 END0 R/W 1 1st Sample is End of Sequence Same definition as END7 but used during the first sample. Because this sequencer has only one entry, this bit must be set. 0 D0 R/W 0 1st Sample Diff Input Select Same definition as D7 but used during the first sample. November 08, 2011 901 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 40: ADC Sample Sequence 3 Operation (ADCSSOP3), offset 0x0B0 This register determines whether the sample from the given conversion on Sample Sequence 3 is saved in the Sample Sequence 3 FIFO or sent to the digital comparator unit. ADC Sample Sequence 3 Operation (ADCSSOP3) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x0B0 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 S0DCOP R/W 0 RO 0 S0DCOP R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 0 Digital Comparator Operation Value Description 1 The sample is sent to the digital comparator unit specified by the S0DCSEL bit in the ADCSSDC03 register, and the value is not written to the FIFO. 0 The sample is saved in Sample Sequence FIFO3. 902 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 41: ADC Sample Sequence 3 Digital Comparator Select (ADCSSDC3), offset 0x0B4 This register determines which digital comparator receives the sample from the given conversion on Sample Sequence 3 if the corresponding SnDCOP bit in the ADCSSOP3 register is set. ADC Sample Sequence 3 Digital Comparator Select (ADCSSDC3) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x0B4 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3:0 S0DCSEL R/W 0x0 S0DCSEL RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sample 0 Digital Comparator Select When the S0DCOP bit in the ADCSSOP3 register is set, this field indicates which digital comparator unit (and its associated set of control registers) receives the sample from Sample Sequencer 3. Note: Values not listed are reserved. Value Description 0x0 Digital Comparator Unit 0 (ADCDCCMP0 and ADCCCTL0) 0x1 Digital Comparator Unit 1 (ADCDCCMP1 and ADCCCTL1) 0x2 Digital Comparator Unit 2 (ADCDCCMP2 and ADCCCTL2) 0x3 Digital Comparator Unit 3 (ADCDCCMP3 and ADCCCTL3) 0x4 Digital Comparator Unit 4 (ADCDCCMP4 and ADCCCTL4) 0x5 Digital Comparator Unit 5 (ADCDCCMP5 and ADCCCTL5) 0x6 Digital Comparator Unit 6 (ADCDCCMP6 and ADCCCTL6) 0x7 Digital Comparator Unit 7 (ADCDCCMP7 and ADCCCTL7) November 08, 2011 903 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 42: ADC Sample Sequence Extended Input Multiplexer Select 3 (ADCSSEMUX3), offset 0x0B8 This register, along with the ADCSSMUX3 register, defines the analog input configuration for the sample in a sequence executed with Sample Sequencer 3. If EMUX0 is set, the MUX0 field in the ADCSSMUX3 register selects from AIN[23:16]. When EMUX0 is clear, the MUX0 field selects from AIN[15:0]. This register is 1 bit wide and contains information for one possible sample. Note that this register is not used when the differential channel designation is used (the Dn bit is set in the ADCSSCTL3 register) because the ADCSSMUX3 register can select all the available pairs. ADC Sample Sequence Extended Input Multiplexer Select 3 (ADCSSEMUX3) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0x0B8 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 EMUX0 R/W 0x0 RO 0 EMUX0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1st Sample Input Select (Upper Bit) The EMUX0 field is used during the only sample of a sequence executed with the sample sequencer. Value Description 1 The sample input is selected from AIN[23:16] using the ADCSSMUX3 register. For example, if the MUX0 field is 0x0, AIN16 is selected. 0 The sample input is selected from AIN[15:0] using the ADCSSMUX3 register. For example, if the MUX0 field is 0x0, AIN0 is selected. 904 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 43: ADC Digital Comparator Reset Initial Conditions (ADCDCRIC), offset 0xD00 This register provides the ability to reset any of the digital comparator interrupt or trigger functions back to their initial conditions. Resetting these functions ensures that the data that is being used by the interrupt and trigger functions in the digital comparator unit is not stale. ADC Digital Comparator Reset Initial Conditions (ADCDCRIC) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0xD00 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 DCTRIG7 DCTRIG6 DCTRIG5 DCTRIG4 DCTRIG3 DCTRIG2 DCTRIG1 DCTRIG0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 7 6 5 4 3 2 1 0 DCINT7 DCINT6 DCINT5 DCINT4 DCINT3 DCINT2 DCINT1 DCINT0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:24 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23 DCTRIG7 R/W 0 Digital Comparator Trigger 7 Value Description 1 Resets the Digital Comparator 7 trigger unit to its initial conditions. 0 No effect. When the trigger has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the trigger, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. After setting this bit, software should wait until the bit clears before continuing. 22 DCTRIG6 R/W 0 Digital Comparator Trigger 6 Value Description 1 Resets the Digital Comparator 6 trigger unit to its initial conditions. 0 No effect. When the trigger has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the trigger, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. November 08, 2011 905 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 21 DCTRIG5 R/W 0 Description Digital Comparator Trigger 5 Value Description 1 Resets the Digital Comparator 5 trigger unit to its initial conditions. 0 No effect. When the trigger has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the trigger, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 20 DCTRIG4 R/W 0 Digital Comparator Trigger 4 Value Description 1 Resets the Digital Comparator 4 trigger unit to its initial conditions. 0 No effect. When the trigger has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the trigger, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 19 DCTRIG3 R/W 0 Digital Comparator Trigger 3 Value Description 1 Resets the Digital Comparator 3 trigger unit to its initial conditions. 0 No effect. When the trigger has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the trigger, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 18 DCTRIG2 R/W 0 Digital Comparator Trigger 2 Value Description 1 Resets the Digital Comparator 2 trigger unit to its initial conditions. 0 No effect. When the trigger has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the trigger, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 906 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 17 DCTRIG1 R/W 0 Description Digital Comparator Trigger 1 Value Description 1 Resets the Digital Comparator 1 trigger unit to its initial conditions. 0 No effect. When the trigger has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the trigger, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 16 DCTRIG0 R/W 0 Digital Comparator Trigger 0 Value Description 1 Resets the Digital Comparator 0 trigger unit to its initial conditions. 0 No effect. When the trigger has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the trigger, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 15:8 reserved RO 0x00 7 DCINT7 R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Digital Comparator Interrupt 7 Value Description 1 Resets the Digital Comparator 7 interrupt unit to its initial conditions. 0 No effect. When the interrupt has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the interrupt, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 6 DCINT6 R/W 0 Digital Comparator Interrupt 6 Value Description 1 Resets the Digital Comparator 6 interrupt unit to its initial conditions. 0 No effect. When the interrupt has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the interrupt, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. November 08, 2011 907 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 5 DCINT5 R/W 0 Description Digital Comparator Interrupt 5 Value Description 1 Resets the Digital Comparator 5 interrupt unit to its initial conditions. 0 No effect. When the interrupt has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the interrupt, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 4 DCINT4 R/W 0 Digital Comparator Interrupt 4 Value Description 1 Resets the Digital Comparator 4 interrupt unit to its initial conditions. 0 No effect. When the interrupt has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the interrupt, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 3 DCINT3 R/W 0 Digital Comparator Interrupt 3 Value Description 1 Resets the Digital Comparator 3 interrupt unit to its initial conditions. 0 No effect. When the interrupt has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the interrupt, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 2 DCINT2 R/W 0 Digital Comparator Interrupt 2 Value Description 1 Resets the Digital Comparator 2 interrupt unit to its initial conditions. 0 No effect. When the interrupt has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the interrupt, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 908 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 DCINT1 R/W 0 Description Digital Comparator Interrupt 1 Value Description 1 Resets the Digital Comparator 1 interrupt unit to its initial conditions. 0 No effect. When the interrupt has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the interrupt, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. 0 DCINT0 R/W 0 Digital Comparator Interrupt 0 Value Description 1 Resets the Digital Comparator 0 interrupt unit to its initial conditions. 0 No effect. When the interrupt has been cleared, this bit is automatically cleared. Because the digital comparators use the current and previous ADC conversion values to determine when to assert the interrupt, it is important to reset the digital comparator to initial conditions when starting a new sequence so that stale data is not used. November 08, 2011 909 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 44: ADC Digital Comparator Control 0 (ADCDCCTL0), offset 0xE00 Register 45: ADC Digital Comparator Control 1 (ADCDCCTL1), offset 0xE04 Register 46: ADC Digital Comparator Control 2 (ADCDCCTL2), offset 0xE08 Register 47: ADC Digital Comparator Control 3 (ADCDCCTL3), offset 0xE0C Register 48: ADC Digital Comparator Control 4 (ADCDCCTL4), offset 0xE10 Register 49: ADC Digital Comparator Control 5 (ADCDCCTL5), offset 0xE14 Register 50: ADC Digital Comparator Control 6 (ADCDCCTL6), offset 0xE18 Register 51: ADC Digital Comparator Control 7 (ADCDCCTL7), offset 0xE1C This register provides the comparison encodings that generate an interrupt and/or PWM trigger. See “Interrupt/ADC-Trigger Selector” on page 1261 for more information on using the ADC digital comparators to trigger a PWM generator. ADC Digital Comparator Control 0 (ADCDCCTL0) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0xE00 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 R/W 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 RO 0 CTE RO 0 R/W 0 CTC R/W 0 CTM Bit/Field Name Type Reset 31:13 reserved RO 0x0000.0 12 CTE R/W 0 reserved RO 0 CIE CIC R/W 0 CIM R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Comparison Trigger Enable Value Description 1 Enables the trigger function state machine. The ADC conversion data is used to determine if a trigger should be generated according to the programming of the CTC and CTM fields. 0 Disables the trigger function state machine. ADC conversion data is ignored by the trigger function. 910 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 11:10 CTC R/W 0x0 Description Comparison Trigger Condition This field specifies the operational region in which a trigger is generated when the ADC conversion data is compared against the values of COMP0 and COMP1. The COMP0 and COMP1 fields are defined in the ADCDCCMPx registers. Value Description 0x0 Low Band ADC Data < COMP0 ≤ COMP1 0x1 Mid Band COMP0 ≤ ADC Data < COMP1 0x2 reserved 0x3 High Band COMP0 ≤ COMP1 ≤ ADC Data 9:8 CTM R/W 0x0 Comparison Trigger Mode This field specifies the mode by which the trigger comparison is made. Value Description 0x0 Always This mode generates a trigger every time the ADC conversion data falls within the selected operational region. 0x1 Once This mode generates a trigger the first time that the ADC conversion data enters the selected operational region. 0x2 Hysteresis Always This mode generates a trigger when the ADC conversion data falls within the selected operational region and continues to generate the trigger until the hysteresis condition is cleared by entering the opposite operational region. Note that the hysteresis modes are only defined for CTC encodings of 0x0 and 0x3. 0x3 Hysteresis Once This mode generates a trigger the first time that the ADC conversion data falls within the selected operational region. No additional triggers are generated until the hysteresis condition is cleared by entering the opposite operational region. Note that the hysteresis modes are only defined for CTC encodings of 0x0 and 0x3. 7:5 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 911 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Bit/Field Name Type Reset 4 CIE R/W 0 Description Comparison Interrupt Enable Value Description 3:2 CIC R/W 0x0 1 Enables the comparison interrupt. The ADC conversion data is used to determine if an interrupt should be generated according to the programming of the CIC and CIM fields. 0 Disables the comparison interrupt. ADC conversion data has no effect on interrupt generation. Comparison Interrupt Condition This field specifies the operational region in which an interrupt is generated when the ADC conversion data is compared against the values of COMP0 and COMP1. The COMP0 and COMP1 fields are defined in the ADCDCCMPx registers. Value Description 0x0 Low Band ADC Data < COMP0 ≤ COMP1 0x1 Mid Band COMP0 ≤ ADC Data < COMP1 0x2 reserved 0x3 High Band COMP0 < COMP1 ≤ ADC Data 1:0 CIM R/W 0x0 Comparison Interrupt Mode This field specifies the mode by which the interrupt comparison is made. Value Description 0x0 Always This mode generates an interrupt every time the ADC conversion data falls within the selected operational region. 0x1 Once This mode generates an interrupt the first time that the ADC conversion data enters the selected operational region. 0x2 Hysteresis Always This mode generates an interrupt when the ADC conversion data falls within the selected operational region and continues to generate the interrupt until the hysteresis condition is cleared by entering the opposite operational region. Note that the hysteresis modes are only defined for CTC encodings of 0x0 and 0x3. 0x3 Hysteresis Once This mode generates an interrupt the first time that the ADC conversion data falls within the selected operational region. No additional interrupts are generated until the hysteresis condition is cleared by entering the opposite operational region. Note that the hysteresis modes are only defined for CTC encodings of 0x0 and 0x3. 912 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 52: ADC Digital Comparator Range 0 (ADCDCCMP0), offset 0xE40 Register 53: ADC Digital Comparator Range 1 (ADCDCCMP1), offset 0xE44 Register 54: ADC Digital Comparator Range 2 (ADCDCCMP2), offset 0xE48 Register 55: ADC Digital Comparator Range 3 (ADCDCCMP3), offset 0xE4C Register 56: ADC Digital Comparator Range 4 (ADCDCCMP4), offset 0xE50 Register 57: ADC Digital Comparator Range 5 (ADCDCCMP5), offset 0xE54 Register 58: ADC Digital Comparator Range 6 (ADCDCCMP6), offset 0xE58 Register 59: ADC Digital Comparator Range 7 (ADCDCCMP7), offset 0xE5C This register defines the comparison values that are used to determine if the ADC conversion data falls in the appropriate operating region. Note: The value in the COMP1 field must be greater than or equal to the value in the COMP0 field or unexpected results can occur. ADC Digital Comparator Range 0 (ADCDCCMP0) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0xE40 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 reserved Type Reset 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset 21 COMP1 RO 0 RO 0 COMP0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:28 reserved RO 0x0 27:16 COMP1 R/W 0x000 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Compare 1 The value in this field is compared against the ADC conversion data. The result of the comparison is used to determine if the data lies within the high-band region. Note that the value of COMP1 must be greater than or equal to the value of COMP0. 15:12 reserved RO 0x0 11:0 COMP0 R/W 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Compare 0 The value in this field is compared against the ADC conversion data. The result of the comparison is used to determine if the data lies within the low-band region. November 08, 2011 913 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 60: ADC Peripheral Properties (ADCPP), offset 0xFC0 The ADCPP register provides information regarding the properties of the ADC module. ADC Peripheral Properties (ADCPP) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0xFC0 Type RO, reset 0x00B0.2187 31 30 29 28 RO 0 RO 0 RO 0 RO 0 15 14 13 RO 0 RO 0 RO 1 27 26 25 24 23 22 21 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 1 12 11 10 9 8 7 6 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 0 reserved Type Reset DC Type Reset 19 18 17 RO 1 RO 0 RO 0 RO 0 RO 0 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 1 TS 20 RSL TYPE CH Bit/Field Name Type Reset 31:24 reserved RO 0 23 TS RO 0x1 16 MSR Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Temperature Sensor Value Description 1 The ADC module has a temperature sensor. 0 The ADC module does not have a temperature sensor. This field provides the similar information as the legacy DC1 register TEMPSNS bit. 22:18 RSL RO 0xC Resolution This field specifies the maximum number of binary bits used to represent the converted sample. The field is encoded as a binary value, in the range of 0 to 32 bits. 17:16 TYPE RO 0x0 ADC Architecture Value Description 0x0 SAR 0x1 - 0x3 Reserved 15:10 DC RO 0x8 Digital Comparator Count This field specifies the number of ADC digital comparators available to the converter. The field is encoded as a binary value, in the range of 0 to 63. This field provides similar information to the legacy DC9 register ADCnDCn bits. 914 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset Description 9:4 CH RO 0x18 ADC Channel Count This field specifies the number of ADC input channels available to the converter. This field is encoded as a binary value, in the range of 0 to 63. This field provides similar information to the legacy DC3 and DC8 register ADCnAINn bits. 3:0 MSR RO 0x7 Maximum ADC Sample Rate This field specifies the maximum number of ADC conversions per second. The MSR field is encoded as follows: Value Description 0x0 Reserved 0x1 125 ksps 0x2 Reserved 0x3 250 ksps 0x4 Reserved 0x5 500 ksps 0x6 Reserved 0x7 1 Msps 0x8 - 0xF Reserved November 08, 2011 915 Texas Instruments-Advance Information Analog-to-Digital Converter (ADC) Register 61: ADC Peripheral Configuration (ADCPC), offset 0xFC4 The ADCPC register provides information regarding the configuration of the peripheral. ADC Peripheral Configuration (ADCPC) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0xFC4 Type R/W, reset 0x0000.0007 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 1 R/W 1 R/W 1 reserved Type Reset reserved Type Reset Bit/Field Name Type 31:4 reserved RO 3:0 SR R/W Reset SR Description 0x0000.0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0x7 ADC Sample Rate This field specifies the number of ADC conversions per second and is used in Run, Sleep, and Deep-sleep modes. The field encoding is based on the legacy RCGC0 register encoding. The programmed sample rate cannot exceed the maximum sample rate specified by the MSR field in the ADCPP register. The SR field is encoded as follows: Value Description 0x0 Reserved 0x1 125 ksps 0x2 Reserved 0x3 250 ksps 0x4 Reserved 0x5 500 ksps 0x6 Reserved 0x7 1 Msps 0x8 - 0xF Reserved 916 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 62: ADC Clock Configuration (ADCCC), offset 0xFC8 The ADCCC register controls the clock source for the ADC module. ADC Clock Configuration (ADCCC) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 Offset 0xFC8 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset CS Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3:0 CS R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. ADC Clock Source The following table specifies the clock source that generates the ADC clock input, see Figure 5-5 on page 223. Value Description 0x0 Either the 16-MHz system clock (if the PLL bypass is in effect) or the 16 MHz clock derived from PLL ÷ 25 (default). Note that when the PLL is bypassed, the system clock must be at least 16 MHz. 0x1 PIOSC The PIOSC provides a 16-MHz clock source for the ADC. If the PIOSC is used as the clock source, the ADC module can continue to operate in Deep-Sleep mode. 0x2 - 0xF Reserved November 08, 2011 917 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) 14 Universal Asynchronous Receivers/Transmitters (UARTs) ® The Stellaris LM4F232H5BB controller includes eight Universal Asynchronous Receiver/Transmitter (UART) with the following features: ■ Programmable baud-rate generator allowing speeds up to 5 Mbps for regular speed (divide by 16) and 10 Mbps for high speed (divide by 8) ■ Separate 16x8 transmit (TX) and receive (RX) FIFOs to reduce CPU interrupt service loading ■ Programmable FIFO length, including 1-byte deep operation providing conventional double-buffered interface ■ FIFO trigger levels of 1/8, 1/4, 1/2, 3/4, and 7/8 ■ Standard asynchronous communication bits for start, stop, and parity ■ Line-break generation and detection ■ Fully programmable serial interface characteristics – 5, 6, 7, or 8 data bits – Even, odd, stick, or no-parity bit generation/detection – 1 or 2 stop bit generation ■ IrDA serial-IR (SIR) encoder/decoder providing – Programmable use of IrDA Serial Infrared (SIR) or UART input/output – Support of IrDA SIR encoder/decoder functions for data rates up to 115.2 Kbps half-duplex – Support of normal 3/16 and low-power (1.41-2.23 μs) bit durations – Programmable internal clock generator enabling division of reference clock by 1 to 256 for low-power mode bit duration ■ Support for communication with ISO 7816 smart cards ■ Modem flow control and status (on UART1) ■ LIN protocol support ■ EIA-485 9-bit support ■ Standard FIFO-level and End-of-Transmission interrupts ■ Efficient transfers using Micro Direct Memory Access Controller (µDMA) – Separate channels for transmit and receive 918 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller – Receive single request asserted when data is in the FIFO; burst request asserted at programmed FIFO level – Transmit single request asserted when there is space in the FIFO; burst request asserted at programmed FIFO level 14.1 Block Diagram Figure 14-1. UART Module Block Diagram PIOSC Clock Control System Clock UARTCTL DMA Request Baud Clock DMA Control UARTDMACTL Interrupt Interrupt Control UARTIFLS UARTIM UARTMIS UARTRIS UARTICR Identification Registers TxFIFO 16 x 8 . . . UARTPCellID0 Transmitter (with SIR Transmit Encoder) UARTPCellID1 UnTx Baud Rate Generator UARTPCellID2 UARTPCellID3 UARTDR UARTPeriphID0 UARTIBRD UARTFBRD Receiver (with SIR Receive Decoder) Control/Status UARTPeriphID1 UnRx UARTRSR/ECR UARTPeriphID2 UARTFR UARTPeriphID3 RxFIFO 16 x 8 UARTLCRH UARTPeriphID4 UARTCTL UARTPeriphID5 UARTILPR UARTLCTL UARTPeriphID6 . . . UARTLSS UARTPeriphID7 UARTLTIM UART9BITADDR UART9BITAMASK UARTPP 14.2 Signal Description The following table lists the external signals of the UART module and describes the function of each. The UART signals are alternate functions for some GPIO signals and default to be GPIO signals at reset, with the exception of the U0Rx and U0Tx pins which default to the UART function. The column in the table below titled "Pin Mux/Pin Assignment" lists the possible GPIO pin placements for these UART signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 698) should be set to choose the UART function. The number in parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control (GPIOPCTL) register (page 717) to assign the UART signal to the specified GPIO port pin. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 674. November 08, 2011 919 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Table 14-1. UART Signals (157BGA) Pin Name Pin Number Pin Mux / Pin Assignment U0Rx L3 a Pin Type Buffer Type PA0 (1) I TTL Description UART module 0 receive. U0Tx M1 PA1 (1) O TTL UART module 0 transmit. U1CTS L1 N9 PC5 (8) PF1 (1) I TTL UART module 1 Clear To Send modem flow control input signal. U1DCD L10 PF2 (1) I TTL UART module 1 Data Carrier Detect modem status input signal. U1DSR K10 PF3 (1) I TTL UART module 1 Data Set Ready modem output control line. U1DTR L9 PF4 (1) O TTL UART module 1 Data Terminal Ready modem status input signal. U1RI B7 PE7 (1) I TTL UART module 1 Ring Indicator modem status input signal. U1RTS L2 M9 PC4 (8) PF0 (1) O TTL UART module 1 Request to Send modem flow control output line. U1Rx F11 L2 PB0 (1) PC4 (2) I TTL UART module 1 receive. U1Tx E11 L1 PB1 (1) PC5 (2) O TTL UART module 1 transmit. U2Rx A3 K7 PD6 (1) PG4 (1) I TTL UART module 2 receive. U2Tx B3 L7 PD7 (1) PG5 (1) O TTL UART module 2 transmit. U3Rx K1 PC6 (1) I TTL UART module 3 receive. U3Tx K2 PC7 (1) O TTL UART module 3 transmit. U4Rx L2 C9 PC4 (1) PJ0 (1) I TTL UART module 4 receive. U4Tx L1 B9 PC5 (1) PJ1 (1) O TTL UART module 4 transmit. U5Rx A5 A9 PE4 (1) PJ2 (1) I TTL UART module 5 receive. U5Tx B5 C8 PE5 (1) PJ3 (1) O TTL UART module 5 transmit. U6Rx A4 D5 PD4 (1) PJ4 (1) I TTL UART module 6 receive. U6Tx B4 C5 PD5 (1) PJ5 (1) O TTL UART module 6 transmit. U7Rx F1 B11 PE0 (1) PK4 (1) I TTL UART module 7 receive. U7Tx F2 B12 PE1 (1) PK5 (1) O TTL UART module 7 transmit. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 14.3 Functional Description Each Stellaris UART performs the functions of parallel-to-serial and serial-to-parallel conversions. It is similar in functionality to a 16C550 UART, but is not register compatible. 920 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller The UART is configured for transmit and/or receive via the TXE and RXE bits of the UART Control (UARTCTL) register (see page 945). Transmit and receive are both enabled out of reset. Before any control registers are programmed, the UART must be disabled by clearing the UARTEN bit in UARTCTL. If the UART is disabled during a TX or RX operation, the current transaction is completed prior to the UART stopping. The UART module also includes a serial IR (SIR) encoder/decoder block that can be connected to an infrared transceiver to implement an IrDA SIR physical layer. The SIR function is programmed using the UARTCTL register. 14.3.1 Transmit/Receive Logic The transmit logic performs parallel-to-serial conversion on the data read from the transmit FIFO. The control logic outputs the serial bit stream beginning with a start bit and followed by the data bits (LSB first), parity bit, and the stop bits according to the programmed configuration in the control registers. See Figure 14-2 on page 921 for details. The receive logic performs serial-to-parallel conversion on the received bit stream after a valid start pulse has been detected. Overrun, parity, frame error checking, and line-break detection are also performed, and their status accompanies the data that is written to the receive FIFO. Figure 14-2. UART Character Frame UnTX LSB 1 5-8 data bits 0 n Parity bit if enabled Start 14.3.2 1-2 stop bits MSB Baud-Rate Generation The baud-rate divisor is a 22-bit number consisting of a 16-bit integer and a 6-bit fractional part. The number formed by these two values is used by the baud-rate generator to determine the bit period. Having a fractional baud-rate divisor allows the UART to generate all the standard baud rates. The 16-bit integer is loaded through the UART Integer Baud-Rate Divisor (UARTIBRD) register (see page 941) and the 6-bit fractional part is loaded with the UART Fractional Baud-Rate Divisor (UARTFBRD) register (see page 942). The baud-rate divisor (BRD) has the following relationship to the system clock (where BRDI is the integer part of the BRD and BRDF is the fractional part, separated by a decimal place.) BRD = BRDI + BRDF = UARTSysClk / (ClkDiv * Baud Rate) where UARTSysClk is the system clock connected to the UART, and ClkDiv is either 16 (if HSE in UARTCTL is clear) or 8 (if HSE is set). The 6-bit fractional number (that is to be loaded into the DIVFRAC bit field in the UARTFBRD register) can be calculated by taking the fractional part of the baud-rate divisor, multiplying it by 64, and adding 0.5 to account for rounding errors: UARTFBRD[DIVFRAC] = integer(BRDF * 64 + 0.5) The UART generates an internal baud-rate reference clock at 8x or 16x the baud-rate (referred to as Baud8 and Baud16, depending on the setting of the HSE bit (bit 5) in UARTCTL). This reference clock is divided by 8 or 16 to generate the transmit clock, and is used for error detection during receive operations. Note that the state of the HSE bit has no effect on clock generation in ISO 7816 smart card mode (when the SMART bit in the UARTCTL register is set). November 08, 2011 921 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Along with the UART Line Control, High Byte (UARTLCRH) register (see page 943), the UARTIBRD and UARTFBRD registers form an internal 30-bit register. This internal register is only updated when a write operation to UARTLCRH is performed, so any changes to the baud-rate divisor must be followed by a write to the UARTLCRH register for the changes to take effect. To update the baud-rate registers, there are four possible sequences: ■ UARTIBRD write, UARTFBRD write, and UARTLCRH write ■ UARTFBRD write, UARTIBRD write, and UARTLCRH write ■ UARTIBRD write and UARTLCRH write ■ UARTFBRD write and UARTLCRH write 14.3.3 Data Transmission Data received or transmitted is stored in two 16-byte FIFOs, though the receive FIFO has an extra four bits per character for status information. For transmission, data is written into the transmit FIFO. If the UART is enabled, it causes a data frame to start transmitting with the parameters indicated in the UARTLCRH register. Data continues to be transmitted until there is no data left in the transmit FIFO. The BUSY bit in the UART Flag (UARTFR) register (see page 937) is asserted as soon as data is written to the transmit FIFO (that is, if the FIFO is non-empty) and remains asserted while data is being transmitted. The BUSY bit is negated only when the transmit FIFO is empty, and the last character has been transmitted from the shift register, including the stop bits. The UART can indicate that it is busy even though the UART may no longer be enabled. When the receiver is idle (the UnRx signal is continuously 1), and the data input goes Low (a start bit has been received), the receive counter begins running and data is sampled on the eighth cycle of Baud16 or fourth cycle of Baud8 depending on the setting of the HSE bit (bit 5) in UARTCTL (described in “Transmit/Receive Logic” on page 921). The start bit is valid and recognized if the UnRx signal is still low on the eighth cycle of Baud16 (HSE clear) or the fourth cycle of Baud 8 (HSE set), otherwise it is ignored. After a valid start bit is detected, successive data bits are sampled on every 16th cycle of Baud16 or 8th cycle of Baud8 (that is, one bit period later) according to the programmed length of the data characters and value of the HSE bit in UARTCTL. The parity bit is then checked if parity mode is enabled. Data length and parity are defined in the UARTLCRH register. Lastly, a valid stop bit is confirmed if the UnRx signal is High, otherwise a framing error has occurred. When a full word is received, the data is stored in the receive FIFO along with any error bits associated with that word. 14.3.4 Serial IR (SIR) The UART peripheral includes an IrDA serial-IR (SIR) encoder/decoder block. The IrDA SIR block provides functionality that converts between an asynchronous UART data stream and a half-duplex serial SIR interface. No analog processing is performed on-chip. The role of the SIR block is to provide a digital encoded output and decoded input to the UART. When enabled, the SIR block uses the UnTx and UnRx pins for the SIR protocol. These signals should be connected to an infrared transceiver to implement an IrDA SIR physical layer link. The SIR block can receive and transmit, but it is only half-duplex so it cannot do both at the same time. Transmission must be stopped before data can be received. The IrDA SIR physical layer specifies a minimum 10-ms delay between transmission and reception.The SIR block has two modes of operation: 922 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ In normal IrDA mode, a zero logic level is transmitted as a high pulse of 3/16th duration of the selected baud rate bit period on the output pin, while logic one levels are transmitted as a static LOW signal. These levels control the driver of an infrared transmitter, sending a pulse of light for each zero. On the reception side, the incoming light pulses energize the photo transistor base of the receiver, pulling its output LOW and driving the UART input pin LOW. ■ In low-power IrDA mode, the width of the transmitted infrared pulse is set to three times the period of the internally generated IrLPBaud16 signal (1.63 µs, assuming a nominal 1.8432 MHz frequency) by changing the appropriate bit in the UARTCR register. See page 940 for more information on IrDA low-power pulse-duration configuration. Figure 14-3 on page 923 shows the UART transmit and receive signals, with and without IrDA modulation. Figure 14-3. IrDA Data Modulation Data bits Start bit UnTx 1 0 0 0 1 Stop bit 0 0 1 1 1 UnTx with IrDA 3 16 Bit period Bit period UnRx with IrDA UnRx 0 1 0 Start 1 0 0 1 1 Data bits 0 1 Stop In both normal and low-power IrDA modes: ■ During transmission, the UART data bit is used as the base for encoding ■ During reception, the decoded bits are transferred to the UART receive logic The IrDA SIR physical layer specifies a half-duplex communication link, with a minimum 10-ms delay between transmission and reception. This delay must be generated by software because it is not automatically supported by the UART. The delay is required because the infrared receiver electronics might become biased or even saturated from the optical power coupled from the adjacent transmitter LED. This delay is known as latency or receiver setup time. 14.3.5 ISO 7816 Support The UART offers basic support to allow communication with an ISO 7816 smartcard. When bit 3 (SMART) of the UARTCTL register is set, the UnTx signal is used as a bit clock, and the UnRx signal is used as the half-duplex communication line connected to the smartcard. A GPIO signal can be used to generate the reset signal to the smartcard. The remaining smartcard signals should be provided by the system design. The maximum clock rate in this mode is system clock / 16. When using ISO 7816 mode, the UARTLCRH register must be set to transmit 8-bit words (WLEN bits 6:5 configured to 0x3) with EVEN parity (PEN set and EPS set). In this mode, the UART automatically uses 2 stop bits, and the STP2 bit of the UARTLCRH register is ignored. November 08, 2011 923 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) If a parity error is detected during transmission, UnRx is pulled Low during the second stop bit. In this case, the UART aborts the transmission, flushes the transmit FIFO and discards any data it contains, and raises a parity error interrupt, allowing software to detect the problem and initiate retransmission of the affected data. Note that the UART does not support automatic retransmission in this case. 14.3.6 Modem Handshake Support This section describes how to configure and use the modem flow control and status signals for UART1 when connected as a DTE (data terminal equipment) or as a DCE (data communications equipment). In general, a modem is a DCE and a computing device that connects to a modem is the DTE. 14.3.6.1 Signaling The status signals provided by UART1 differ based on whether the UART is used as a DTE or DCE. When used as a DTE, the modem flow control and status signals are defined as: ■ U1CTS is Clear To Send ■ U1DSR is Data Set Ready ■ U1DCD is Data Carrier Detect ■ U1RI is Ring Indicator ■ U1RTS is Request To Send ■ U1DTR is Data Terminal Ready When used as a DCE, the the modem flow control and status signals are defined as: ■ U1CTS is Request To Send ■ U1DSR is Data Terminal Ready ■ U1RTS is Clear To Send ■ U1DTR is Data Set Ready Note that the support for DCE functions Data Carrier Detect and Ring Indicator are not provided. If these signals are required, their function can be emulated by using a general-purpose I/O signal and providing software support. 14.3.6.2 Flow Control Flow control can be accomplished by either hardware or software. The following sections describe the different methods. Hardware Flow Control (RTS/CTS) Hardware flow control between two devices is accomplished by connecting the U1RTS output to the Clear-To-Send input on the receiving device, and connecting the Request-To-Send output on the receiving device to the U1CTS input. The U1CTS input controls the transmitter. The transmitter may only transmit data when the U1CTS input is asserted. The U1RTS output signal indicates the state of the receive FIFO. U1CTS remains 924 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller asserted until the preprogrammed watermark level is reached, indicating that the Receive FIFO has no space to store additional characters. The UARTCTL register bits 15 (CTSEN) and 14 (RTSEN) specify the flow control mode as shown in Table 14-2 on page 925. Table 14-2. Flow Control Mode Description CTSEN RTSEN 1 1 RTS and CTS flow control enabled 1 0 Only CTS flow control enabled 0 1 Only RTS flow control enabled 0 0 Both RTS and CTS flow control disabled Note that when RTSEN is 1, software cannot modify the U1RTS output value through the UARTCTL register Request to Send (RTS) bit, and the status of the RTS bit should be ignored. Software Flow Control (Modem Status Interrupts) Software flow control between two devices is accomplished by using interrupts to indicate the status of the UART. Interrupts may be generated for the U1DSR, U1DCD, U1CTS, and U1RI signals using bits 3:0 of the UARTIM register, respectively. The raw and masked interrupt status may be checked using the UARTRIS and UARTMIS register. These interrupts may be cleared using the UARTICR register. 14.3.7 LIN Support The UART module offers hardware support for the LIN protocol as either a master or a slave. The LIN mode is enabled by setting the LIN bit in the UARTCTL register. A LIN message is identified by the use of a Sync Break at the beginning of the message. The Sync Break is a transmission of a series of 0s. The Sync Break is followed by the Sync data field (0x55). Figure 14-4 on page 925 illustrates the structure of a LIN message. Figure 14-4. LIN Message Message Frame Header Synch Break Synch Field Response Ident Field Data Field(s) In-Frame Response Data Field Checksum Field Interbyte Space The UART should be configured as followed to operate in LIN mode: 1. Configure the UART for 1 start bit, 8 data bits, no parity, and 1 stop bit. Enable the Transmit FIFO. November 08, 2011 925 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) 2. Set the LIN bit in the UARTCTL register. When preparing to send a LIN message, the TXFIFO should contain the Sync data (0x55) at FIFO location 0 and the Identifier data at location 1, followed by the data to be transmitted, and with the checksum in the final FIFO entry. 14.3.7.1 LIN Master The UART is enabled to be the LIN master by setting the MASTER bit in the UARTLCTL register. The length of the Sync Break is programmable using the BLEN field in the UARTLCTL register and can be 13-16 bits (baud clock cycles). 14.3.7.2 LIN Slave The LIN UART slave is required to adjust its baud rate to that of the LIN master. In slave mode, the LIN UART recognizes the Sync Break, which must be at least 13 bits in duration. A timer is provided to capture timing data on the 1st and 5th falling edges of the Sync field so that the baud rate can be adjusted to match the master. After detecting a Sync Break, the UART waits for the synchronization field. The first falling edge generates an interrupt using the LME1RIS bit in the UARTRIS register, and the timer value is captured and stored in the UARTLSS register (T1). On the fifth falling edge, a second interrupt is generated using the LME5RIS bit in the UARTRIS register, and the timer value is captured again (T2). The actual baud rate can be calculated using (T2-T1)/8, and the local baud rate should be adjusted as needed. Figure 14-5 on page 926 illustrates the synchronization field. Figure 14-5. LIN Synchronization Field Sync Break 0 1 2 3 4 5 6 7 8 Synch Field 9 10 11 12 13 0 1 2 Edge 1 3 4 5 6 Edge 5 7 8 8 Tbit Sync Break Detect 14.3.8 9-Bit UART Mode The UART provides a 9-bit mode that is enabled with the 9BITEN bit in the UART9BITADDR register. This feature is useful in a multi-drop configuration of the UART where a single master connected to multiple slaves can communicate with a particular slave through its address or address range along with a qualifier for an address byte. All the slaves check for the address qualifier in the place of the parity bit and, if set, then compare the byte received with the preprogrammed address. If the address matches, then it receives or sends further data. If the address does not match, it drops the address byte and any subsequent data bytes. If the UART is in 9-bit mode, then the receiver operates with no parity mode. The address can be predefined to match with the received byte and it can be configured with the UART9BITADDR register. The matching can be extended to an address range using the address mask UART9BITAMASK that is ANDed with UART9BITADDR to form the range. By default, the UART9BITAMASK is 0xFF. If the byte received that follows 9th bit set then it will be compared with UART9BITADDRRNG (address range read-only status register). Upon not finding a match, the rest of the data bytes with the 9th bit cleared are dropped. If a match is found, then an interrupt is generated to the NVIC for further 926 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller action. The subsequent data bytes with the cleared 9th bit are stored in the FIFO. Software can mask this interrupt in case μDMA and/or FIFO operations are enabled for this instance and processor intervention is not required. All the send transactions with 9-bit mode are data bytes and the 9th bit is cleared. Software can override the 9th bit to be set (to indicate address) by overriding the parity settings to sticky parity with odd parity enabled for a particular byte. To match the transmission time with correct parity settings, the address byte can be transmitted as a single then a burst transfer. The Transmit FIFO does not hold the address/data bit, hence software should take care of enabling the address bit appropriately. 14.3.9 FIFO Operation The UART has two 16x8 FIFOs; one for transmit and one for receive. Both FIFOs are accessed via the UART Data (UARTDR) register (see page 932). Read operations of the UARTDR register return a 12-bit value consisting of 8 data bits and 4 error flags while write operations place 8-bit data in the transmit FIFO. Out of reset, both FIFOs are disabled and act as 1-byte-deep holding registers. The FIFOs are enabled by setting the FEN bit in UARTLCRH (page 943). FIFO status can be monitored via the UART Flag (UARTFR) register (see page 937) and the UART Receive Status (UARTRSR) register. Hardware monitors empty, full and overrun conditions. The UARTFR register contains empty and full flags (TXFE, TXFF, RXFE, and RXFF bits), and the UARTRSR register shows overrun status via the OE bit. If the FIFOs are disabled, the empty and full flags are set according to the status of the 1-byte-deep holding registers. The trigger points at which the FIFOs generate interrupts is controlled via the UART Interrupt FIFO Level Select (UARTIFLS) register (see page 949). Both FIFOs can be individually configured to trigger interrupts at different levels. Available configurations include ⅛, ¼, ½, ¾, and ⅞. For example, if the ¼ option is selected for the receive FIFO, the UART generates a receive interrupt after 4 data bytes are received. Out of reset, both FIFOs are configured to trigger an interrupt at the ½ mark. 14.3.10 Interrupts The UART can generate interrupts when the following conditions are observed: ■ Overrun Error ■ Break Error ■ Parity Error ■ Framing Error ■ Receive Timeout ■ Transmit (when condition defined in the TXIFLSEL bit in the UARTIFLS register is met, or if the EOT bit in UARTCTL is set, when the last bit of all transmitted data leaves the serializer) ■ Receive (when condition defined in the RXIFLSEL bit in the UARTIFLS register is met) All of the interrupt events are ORed together before being sent to the interrupt controller, so the UART can only generate a single interrupt request to the controller at any given time. Software can service multiple interrupt events in a single interrupt service routine by reading the UART Masked Interrupt Status (UARTMIS) register (see page 959). The interrupt events that can trigger a controller-level interrupt are defined in the UART Interrupt Mask (UARTIM) register (see page 951) by setting the corresponding IM bits. If interrupts are not November 08, 2011 927 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) used, the raw interrupt status is always visible via the UART Raw Interrupt Status (UARTRIS) register (see page 955). Interrupts are always cleared (for both the UARTMIS and UARTRIS registers) by writing a 1 to the corresponding bit in the UART Interrupt Clear (UARTICR) register (see page 963). The receive timeout interrupt is asserted when the receive FIFO is not empty, and no further data is received over a 32-bit period. The receive timeout interrupt is cleared either when the FIFO becomes empty through reading all the data (or by reading the holding register), or when a 1 is written to the corresponding bit in the UARTICR register. The receive interrupt changes state when one of the following events occurs: ■ If the FIFOs are enabled and the receive FIFO reaches the programmed trigger level, the RXRIS bit is set. The receive interrupt is cleared by reading data from the receive FIFO until it becomes less than the trigger level, or by clearing the interrupt by writing a 1 to the RXIC bit. ■ If the FIFOs are disabled (have a depth of one location) and data is received thereby filling the location, the RXRIS bit is set. The receive interrupt is cleared by performing a single read of the receive FIFO, or by clearing the interrupt by writing a 1 to the RXIC bit. The transmit interrupt changes state when one of the following events occurs: ■ If the FIFOs are enabled and the transmit FIFO reaches the programmed trigger level, the TXRIS bit is set. The transmit interrupt is cleared by writing data to the transmit FIFO until it becomes greater than the trigger level, or by clearing the interrupt by writing a 1 to the TXIC bit. ■ If the FIFOs are disabled (have a depth of one location) and there is no data present in the transmitters single location, the TXRIS bit is set. It is cleared by performing a single write to the transmit FIFO, or by clearing the interrupt by writing a 1 to the TXIC bit. 14.3.11 Loopback Operation The UART can be placed into an internal loopback mode for diagnostic or debug work by setting the LBE bit in the UARTCTL register (see page 945). In loopback mode, data transmitted on the UnTx output is received on the UnRx input. Note that the LBE bit should be set before the UART is enabled. 14.3.12 DMA Operation The UART provides an interface to the μDMA controller with separate channels for transmit and receive. The DMA operation of the UART is enabled through the UART DMA Control (UARTDMACTL) register. When DMA operation is enabled, the UART asserts a DMA request on the receive or transmit channel when the associated FIFO can transfer data. For the receive channel, a single transfer request is asserted whenever any data is in the receive FIFO. A burst transfer request is asserted whenever the amount of data in the receive FIFO is at or above the FIFO trigger level configured in the UARTIFLS register. For the transmit channel, a single transfer request is asserted whenever there is at least one empty location in the transmit FIFO. The burst request is asserted whenever the transmit FIFO contains fewer characters than the FIFO trigger level. The single and burst DMA transfer requests are handled automatically by the μDMA controller depending on how the DMA channel is configured. To enable DMA operation for the receive channel, set the RXDMAE bit of the DMA Control (UARTDMACTL) register. To enable DMA operation for the transmit channel, set the TXDMAE bit of the UARTDMACTL register. The UART can also be configured to stop using DMA for the receive channel if a receive error occurs. If the DMAERR bit of the UARTDMACR register is set and a receive 928 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller error occurs, the DMA receive requests are automatically disabled. This error condition can be cleared by clearing the appropriate UART error interrupt. If DMA is enabled, then the μDMA controller triggers an interrupt when a transfer is complete. The interrupt occurs on the UART interrupt vector. Therefore, if interrupts are used for UART operation and DMA is enabled, the UART interrupt handler must be designed to handle the μDMA completion interrupt. See “Micro Direct Memory Access (μDMA)” on page 610 for more details about programming the μDMA controller. 14.4 Initialization and Configuration To enable and initialize the UART, the following steps are necessary: 1. Enable the UART module using the RCGCUART register (see page 394). 2. Enable the clock to the appropriate GPIO module via the RCGCGPIO register (see page 389). To find out which GPIO port to enable, refer to Table 23-5 on page 1398. 3. Set the GPIO AFSEL bits for the appropriate pins (see page 698). To determine which GPIOs to configure, see Table 23-4 on page 1387. 4. Configure the GPIO current level and/or slew rate as specified for the mode selected (see page 700 and page 709). 5. Configure the PMCn fields in the GPIOPCTL register to assign the UART signals to the appropriate pins (see page 717 and Table 23-5 on page 1398). To use the UART, the peripheral clock must be enabled by setting the appropriate bit in the RCGCUART register (page 394). In addition, the clock to the appropriate GPIO module must be enabled via the RCGCGPIO register (page 389) in the System Control module. To find out which GPIO port to enable, refer to Table 23-5 on page 1398. This section discusses the steps that are required to use a UART module. For this example, the UART clock is assumed to be 20 MHz, and the desired UART configuration is: ■ 115200 baud rate ■ Data length of 8 bits ■ One stop bit ■ No parity ■ FIFOs disabled ■ No interrupts The first thing to consider when programming the UART is the baud-rate divisor (BRD), because the UARTIBRD and UARTFBRD registers must be written before the UARTLCRH register. Using the equation described in “Baud-Rate Generation” on page 921, the BRD can be calculated: BRD = 20,000,000 / (16 * 115,200) = 10.8507 November 08, 2011 929 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) which means that the DIVINT field of the UARTIBRD register (see page 941) should be set to 10 decimal or 0xA. The value to be loaded into the UARTFBRD register (see page 942) is calculated by the equation: UARTFBRD[DIVFRAC] = integer(0.8507 * 64 + 0.5) = 54 With the BRD values in hand, the UART configuration is written to the module in the following order: 1. Disable the UART by clearing the UARTEN bit in the UARTCTL register. 2. Write the integer portion of the BRD to the UARTIBRD register. 3. Write the fractional portion of the BRD to the UARTFBRD register. 4. Write the desired serial parameters to the UARTLCRH register (in this case, a value of 0x0000.0060). 5. Optionally, configure the µDMA channel (see “Micro Direct Memory Access (μDMA)” on page 610) and enable the DMA option(s) in the UARTDMACTL register. 6. Enable the UART by setting the UARTEN bit in the UARTCTL register. 14.5 Register Map Table 14-3 on page 930 lists the UART registers. The offset listed is a hexadecimal increment to the register’s address, relative to that UART’s base address: ■ ■ ■ ■ ■ ■ ■ ■ UART0: 0x4000.C000 UART1: 0x4000.D000 UART2: 0x4000.E000 UART3: 0x4000.F000 UART4: 0x4001.0000 UART5: 0x4001.1000 UART6: 0x4001.2000 UART7: 0x4001.3000 Note that the UART module clock must be enabled before the registers can be programmed (see page 394). There must be a delay of 3 system clocks after the UART module clock is enabled before any UART module registers are accessed. Note: The UART must be disabled (see the UARTEN bit in the UARTCTL register on page 945) before any of the control registers are reprogrammed. When the UART is disabled during a TX or RX operation, the current transaction is completed prior to the UART stopping. Table 14-3. UART Register Map Offset Name Type Reset Description See page 0x000 UARTDR R/W 0x0000.0000 UART Data 932 0x004 UARTRSR/UARTECR R/W 0x0000.0000 UART Receive Status/Error Clear 934 0x018 UARTFR RO 0x0000.0090 UART Flag 937 0x020 UARTILPR R/W 0x0000.0000 UART IrDA Low-Power Register 940 0x024 UARTIBRD R/W 0x0000.0000 UART Integer Baud-Rate Divisor 941 930 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 14-3. UART Register Map (continued) Name Type Reset 0x028 UARTFBRD R/W 0x0000.0000 UART Fractional Baud-Rate Divisor 942 0x02C UARTLCRH R/W 0x0000.0000 UART Line Control 943 0x030 UARTCTL R/W 0x0000.0300 UART Control 945 0x034 UARTIFLS R/W 0x0000.0012 UART Interrupt FIFO Level Select 949 0x038 UARTIM R/W 0x0000.0000 UART Interrupt Mask 951 0x03C UARTRIS RO 0x0000.000F UART Raw Interrupt Status 955 0x040 UARTMIS RO 0x0000.0000 UART Masked Interrupt Status 959 0x044 UARTICR W1C 0x0000.0000 UART Interrupt Clear 963 0x048 UARTDMACTL R/W 0x0000.0000 UART DMA Control 965 0x090 UARTLCTL R/W 0x0000.0000 UART LIN Control 966 0x094 UARTLSS RO 0x0000.0000 UART LIN Snap Shot 967 0x098 UARTLTIM RO 0x0000.0000 UART LIN Timer 968 0x0A4 UART9BITADDR R/W 0x0000.0000 UART 9-Bit Self Address 969 0x0A8 UART9BITAMASK R/W 0x0000.00FF UART 9-Bit Self Address Mask 970 0xFC0 UARTPP RO 0x0000.0003 UART Peripheral Properties 971 0xFC8 UARTCC R/W 0x0000.0000 UART Clock Configuration 972 0xFD0 UARTPeriphID4 RO 0x0000.0000 UART Peripheral Identification 4 973 0xFD4 UARTPeriphID5 RO 0x0000.0000 UART Peripheral Identification 5 974 0xFD8 UARTPeriphID6 RO 0x0000.0000 UART Peripheral Identification 6 975 0xFDC UARTPeriphID7 RO 0x0000.0000 UART Peripheral Identification 7 976 0xFE0 UARTPeriphID0 RO 0x0000.0060 UART Peripheral Identification 0 977 0xFE4 UARTPeriphID1 RO 0x0000.0000 UART Peripheral Identification 1 978 0xFE8 UARTPeriphID2 RO 0x0000.0018 UART Peripheral Identification 2 979 0xFEC UARTPeriphID3 RO 0x0000.0001 UART Peripheral Identification 3 980 0xFF0 UARTPCellID0 RO 0x0000.000D UART PrimeCell Identification 0 981 0xFF4 UARTPCellID1 RO 0x0000.00F0 UART PrimeCell Identification 1 982 0xFF8 UARTPCellID2 RO 0x0000.0005 UART PrimeCell Identification 2 983 0xFFC UARTPCellID3 RO 0x0000.00B1 UART PrimeCell Identification 3 984 14.6 Description See page Offset Register Descriptions The remainder of this section lists and describes the UART registers, in numerical order by address offset. November 08, 2011 931 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 1: UART Data (UARTDR), offset 0x000 Important: This register is read-sensitive. See the register description for details. This register is the data register (the interface to the FIFOs). For transmitted data, if the FIFO is enabled, data written to this location is pushed onto the transmit FIFO. If the FIFO is disabled, data is stored in the transmitter holding register (the bottom word of the transmit FIFO). A write to this register initiates a transmission from the UART. For received data, if the FIFO is enabled, the data byte and the 4-bit status (break, frame, parity, and overrun) is pushed onto the 12-bit wide receive FIFO. If the FIFO is disabled, the data byte and status are stored in the receiving holding register (the bottom word of the receive FIFO). The received data can be retrieved by reading this register. UART Data (UARTDR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 15 14 13 12 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 11 10 9 8 OE BE PE FE RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:12 reserved RO 0x0000.0 11 OE RO 0 DATA R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Overrun Error Value Description 1 New data was received when the FIFO was full, resulting in data loss. 0 No data has been lost due to a FIFO overrun. 932 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 10 BE RO 0 Description UART Break Error Value Description 1 A break condition has been detected, indicating that the receive data input was held Low for longer than a full-word transmission time (defined as start, data, parity, and stop bits). 0 No break condition has occurred In FIFO mode, this error is associated with the character at the top of the FIFO. When a break occurs, only one 0 character is loaded into the FIFO. The next character is only enabled after the received data input goes to a 1 (marking state), and the next valid start bit is received. 9 PE RO 0 UART Parity Error Value Description 1 The parity of the received data character does not match the parity defined by bits 2 and 7 of the UARTLCRH register. 0 No parity error has occurred In FIFO mode, this error is associated with the character at the top of the FIFO. 8 FE RO 0 UART Framing Error Value Description 7:0 DATA R/W 0x00 1 The received character does not have a valid stop bit (a valid stop bit is 1). 0 No framing error has occurred Data Transmitted or Received Data that is to be transmitted via the UART is written to this field. When read, this field contains the data that was received by the UART. November 08, 2011 933 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 2: UART Receive Status/Error Clear (UARTRSR/UARTECR), offset 0x004 The UARTRSR/UARTECR register is the receive status register/error clear register. In addition to the UARTDR register, receive status can also be read from the UARTRSR register. If the status is read from this register, then the status information corresponds to the entry read from UARTDR prior to reading UARTRSR. The status information for overrun is set immediately when an overrun condition occurs. The UARTRSR register cannot be written. A write of any value to the UARTECR register clears the framing, parity, break, and overrun errors. All the bits are cleared on reset. Read-Only Status Register UART Receive Status/Error Clear (UARTRSR/UARTECR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x004 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 OE BE PE FE RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 OE RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Overrun Error Value Description 1 New data was received when the FIFO was full, resulting in data loss. 0 No data has been lost due to a FIFO overrun. This bit is cleared by a write to UARTECR. The FIFO contents remain valid because no further data is written when the FIFO is full, only the contents of the shift register are overwritten. The CPU must read the data in order to empty the FIFO. 934 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 2 BE RO 0 Description UART Break Error Value Description 1 A break condition has been detected, indicating that the receive data input was held Low for longer than a full-word transmission time (defined as start, data, parity, and stop bits). 0 No break condition has occurred This bit is cleared to 0 by a write to UARTECR. In FIFO mode, this error is associated with the character at the top of the FIFO. When a break occurs, only one 0 character is loaded into the FIFO. The next character is only enabled after the receive data input goes to a 1 (marking state) and the next valid start bit is received. 1 PE RO 0 UART Parity Error Value Description 1 The parity of the received data character does not match the parity defined by bits 2 and 7 of the UARTLCRH register. 0 No parity error has occurred This bit is cleared to 0 by a write to UARTECR. 0 FE RO 0 UART Framing Error Value Description 1 The received character does not have a valid stop bit (a valid stop bit is 1). 0 No framing error has occurred This bit is cleared to 0 by a write to UARTECR. In FIFO mode, this error is associated with the character at the top of the FIFO. Write-Only Error Clear Register UART Receive Status/Error Clear (UARTRSR/UARTECR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x004 Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 WO 0 WO 0 WO 0 WO 0 3 2 1 0 WO 0 WO 0 WO 0 WO 0 reserved Type Reset WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset WO 0 WO 0 WO 0 WO 0 WO 0 DATA WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 November 08, 2011 WO 0 935 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 31:8 reserved WO 0x0000.00 7:0 DATA WO 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Error Clear A write to this register of any data clears the framing, parity, break, and overrun flags. 936 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 3: UART Flag (UARTFR), offset 0x018 The UARTFR register is the flag register. After reset, the TXFF, RXFF, and BUSY bits are 0, and TXFE and RXFE bits are 1. The RI, DCD, DSR and CTS bits indicate the modem flow control and status. Note that the modem bits are only implemented on UART1 and are reserved on UART0 and UART2. UART Flag (UARTFR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x018 Type RO, reset 0x0000.0090 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 15 14 13 RO 0 RO 0 RO 0 RO 0 12 11 10 9 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:9 reserved RO 0x0000.00 8 RI RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RI TXFE RXFF TXFF RXFE BUSY DCD DSR CTS RO 0 RO 1 RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Ring Indicator Value Description 1 The U1RI signal is asserted. 0 The U1RI signal is not asserted. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 7 TXFE RO 1 UART Transmit FIFO Empty The meaning of this bit depends on the state of the FEN bit in the UARTLCRH register. Value Description 1 If the FIFO is disabled (FEN is 0), the transmit holding register is empty. If the FIFO is enabled (FEN is 1), the transmit FIFO is empty. 0 The transmitter has data to transmit. November 08, 2011 937 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 6 RXFF RO 0 Description UART Receive FIFO Full The meaning of this bit depends on the state of the FEN bit in the UARTLCRH register. Value Description 1 If the FIFO is disabled (FEN is 0), the receive holding register is full. If the FIFO is enabled (FEN is 1), the receive FIFO is full. 0 5 TXFF RO 0 The receiver can receive data. UART Transmit FIFO Full The meaning of this bit depends on the state of the FEN bit in the UARTLCRH register. Value Description 1 If the FIFO is disabled (FEN is 0), the transmit holding register is full. If the FIFO is enabled (FEN is 1), the transmit FIFO is full. 0 4 RXFE RO 1 The transmitter is not full. UART Receive FIFO Empty The meaning of this bit depends on the state of the FEN bit in the UARTLCRH register. Value Description 1 If the FIFO is disabled (FEN is 0), the receive holding register is empty. If the FIFO is enabled (FEN is 1), the receive FIFO is empty. 0 3 BUSY RO 0 The receiver is not empty. UART Busy Value Description 1 The UART is busy transmitting data. This bit remains set until the complete byte, including all stop bits, has been sent from the shift register. 0 The UART is not busy. This bit is set as soon as the transmit FIFO becomes non-empty (regardless of whether UART is enabled). 2 DCD RO 0 Data Carrier Detect Value Description 1 The U1DCD signal is asserted. 0 The U1DCD signal is not asserted. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 938 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 DSR RO 0 Description Data Set Ready Value Description 1 The U1DSR signal is asserted. 0 The U1DSR signal is not asserted. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 0 CTS RO 0 Clear To Send Value Description 1 The U1CTS signal is asserted. 0 The U1CTS signal is not asserted. This bit is implemented only on UART1 and is reserved for UART0 and UART2. November 08, 2011 939 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 4: UART IrDA Low-Power Register (UARTILPR), offset 0x020 The UARTILPR register stores the 8-bit low-power counter divisor value used to derive the low-power SIR pulse width clock by dividing down the system clock (SysClk). All the bits are cleared when reset. The internal IrLPBaud16 clock is generated by dividing down SysClk according to the low-power divisor value written to UARTILPR. The duration of SIR pulses generated when low-power mode is enabled is three times the period of the IrLPBaud16 clock. The low-power divisor value is calculated as follows: ILPDVSR = SysClk / FIrLPBaud16 where FIrLPBaud16 is nominally 1.8432 MHz. The divisor must be programmed such that 1.42 MHz < FIrLPBaud16 < 2.12 MHz, resulting in a low-power pulse duration of 1.41–2.11 μs (three times the period of IrLPBaud16). The minimum frequency of IrLPBaud16 ensures that pulses less than one period of IrLPBaud16 are rejected, but pulses greater than 1.4 μs are accepted as valid pulses. Note: Zero is an illegal value. Programming a zero value results in no IrLPBaud16 pulses being generated. UART IrDA Low-Power Register (UARTILPR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x020 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 ILPDVSR RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 ILPDVSR R/W 0x00 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. IrDA Low-Power Divisor This field contains the 8-bit low-power divisor value. 940 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 5: UART Integer Baud-Rate Divisor (UARTIBRD), offset 0x024 The UARTIBRD register is the integer part of the baud-rate divisor value. All the bits are cleared on reset. The minimum possible divide ratio is 1 (when UARTIBRD=0), in which case the UARTFBRD register is ignored. When changing the UARTIBRD register, the new value does not take effect until transmission/reception of the current character is complete. Any changes to the baud-rate divisor must be followed by a write to the UARTLCRH register. See “Baud-Rate Generation” on page 921 for configuration details. UART Integer Baud-Rate Divisor (UARTIBRD) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 DIVINT Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 DIVINT R/W 0x0000 Integer Baud-Rate Divisor November 08, 2011 941 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 6: UART Fractional Baud-Rate Divisor (UARTFBRD), offset 0x028 The UARTFBRD register is the fractional part of the baud-rate divisor value. All the bits are cleared on reset. When changing the UARTFBRD register, the new value does not take effect until transmission/reception of the current character is complete. Any changes to the baud-rate divisor must be followed by a write to the UARTLCRH register. See “Baud-Rate Generation” on page 921 for configuration details. UART Fractional Baud-Rate Divisor (UARTFBRD) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x028 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 DIVFRAC RO 0 Bit/Field Name Type Reset 31:6 reserved RO 0x0000.000 5:0 DIVFRAC R/W 0x0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Fractional Baud-Rate Divisor 942 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 7: UART Line Control (UARTLCRH), offset 0x02C The UARTLCRH register is the line control register. Serial parameters such as data length, parity, and stop bit selection are implemented in this register. When updating the baud-rate divisor (UARTIBRD and/or UARTIFRD), the UARTLCRH register must also be written. The write strobe for the baud-rate divisor registers is tied to the UARTLCRH register. UART Line Control (UARTLCRH) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x02C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 FEN STP2 EPS PEN BRK R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset SPS RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 SPS R/W 0 R/W 0 WLEN R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Stick Parity Select When bits 1, 2, and 7 of UARTLCRH are set, the parity bit is transmitted and checked as a 0. When bits 1 and 7 are set and 2 is cleared, the parity bit is transmitted and checked as a 1. When this bit is cleared, stick parity is disabled. 6:5 WLEN R/W 0x0 UART Word Length The bits indicate the number of data bits transmitted or received in a frame as follows: Value Description 0x0 5 bits (default) 0x1 6 bits 0x2 7 bits 0x3 8 bits November 08, 2011 943 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 4 FEN R/W 0 Description UART Enable FIFOs Value Description 3 STP2 R/W 0 1 The transmit and receive FIFO buffers are enabled (FIFO mode). 0 The FIFOs are disabled (Character mode). The FIFOs become 1-byte-deep holding registers. UART Two Stop Bits Select Value Description 1 Two stop bits are transmitted at the end of a frame. The receive logic does not check for two stop bits being received. When in 7816 smartcard mode (the SMART bit is set in the UARTCTL register), the number of stop bits is forced to 2. 0 2 EPS R/W 0 One stop bit is transmitted at the end of a frame. UART Even Parity Select Value Description 1 Even parity generation and checking is performed during transmission and reception, which checks for an even number of 1s in data and parity bits. 0 Odd parity is performed, which checks for an odd number of 1s. This bit has no effect when parity is disabled by the PEN bit. 1 PEN R/W 0 UART Parity Enable Value Description 0 BRK R/W 0 1 Parity checking and generation is enabled. 0 Parity is disabled and no parity bit is added to the data frame. UART Send Break Value Description 1 A Low level is continually output on the UnTx signal, after completing transmission of the current character. For the proper execution of the break command, software must set this bit for at least two frames (character periods). 0 Normal use. 944 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 8: UART Control (UARTCTL), offset 0x030 The UARTCTL register is the control register. All the bits are cleared on reset except for the Transmit Enable (TXE) and Receive Enable (RXE) bits, which are set. To enable the UART module, the UARTEN bit must be set. If software requires a configuration change in the module, the UARTEN bit must be cleared before the configuration changes are written. If the UART is disabled during a transmit or receive operation, the current transaction is completed prior to the UART stopping. Note that bits [15:14,11:10] are only implemented on UART1. These bits are reserved on UART0 and UART2. Note: The UARTCTL register should not be changed while the UART is enabled or else the results are unpredictable. The following sequence is recommended for making changes to the UARTCTL register. 1. Disable the UART. 2. Wait for the end of transmission or reception of the current character. 3. Flush the transmit FIFO by clearing bit 4 (FEN) in the line control register (UARTLCRH). 4. Reprogram the control register. 5. Enable the UART. UART Control (UARTCTL) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x030 Type R/W, reset 0x0000.0300 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 CTSEN RTSEN RTS DTR RXE TXE R/W 0 R/W 0 R/W 0 R/W 0 R/W 1 R/W 1 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 LBE LIN HSE EOT SMART SIRLP SIREN UARTEN R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset Type Reset reserved RO 0 RO 0 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 945 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 15 CTSEN R/W 0 Description Enable Clear To Send Value Description 1 CTS hardware flow control is enabled. Data is only transmitted when the U1CTS signal is asserted. 0 CTS hardware flow control is disabled. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 14 RTSEN R/W 0 Enable Request to Send Value Description 1 RTS hardware flow control is enabled. Data is only requested (by asserting U1RTS) when the receive FIFO has available entries. 0 RTS hardware flow control is disabled. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 13:12 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 11 RTS R/W 0 Request to Send When RTSEN is clear, the status of this bit is reflected on the U1RTS signal. If RTSEN is set, this bit is ignored on a write and should be ignored on read. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 10 DTR R/W 0 Data Terminal Ready This bit sets the state of the U1DTR output. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 9 RXE R/W 1 UART Receive Enable Value Description 1 The receive section of the UART is enabled. 0 The receive section of the UART is disabled. If the UART is disabled in the middle of a receive, it completes the current character before stopping. Note: To enable reception, the UARTEN bit must also be set. 946 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 8 TXE R/W 1 Description UART Transmit Enable Value Description 1 The transmit section of the UART is enabled. 0 The transmit section of the UART is disabled. If the UART is disabled in the middle of a transmission, it completes the current character before stopping. Note: 7 LBE R/W 0 To enable transmission, the UARTEN bit must also be set. UART Loop Back Enable Value Description 6 LIN R/W 0 1 The UnTx path is fed through the UnRx path. 0 Normal operation. LIN Mode Enable Value Description 5 HSE R/W 0 1 The UART operates in LIN mode. 0 Normal operation. High-Speed Enable Value Description 0 The UART is clocked using the system clock divided by 16. 1 The UART is clocked using the system clock divided by 8. Note: System clock used is also dependent on the baud-rate divisor configuration (see page 941) and page 942). The state of this bit has no effect on clock generation in ISO 7816 smart card mode (the SMART bit is set). 4 EOT R/W 0 End of Transmission This bit determines the behavior of the TXRIS bit in the UARTRIS register. Value Description 1 The TXRIS bit is set only after all transmitted data, including stop bits, have cleared the serializer. 0 The TXRIS bit is set when the transmit FIFO condition specified in UARTIFLS is met. November 08, 2011 947 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 3 SMART R/W 0 Description ISO 7816 Smart Card Support Value Description 1 The UART operates in Smart Card mode. 0 Normal operation. The application must ensure that it sets 8-bit word length (WLEN set to 0x3) and even parity (PEN set to 1, EPS set to 1, SPS set to 0) in UARTLCRH when using ISO 7816 mode. In this mode, the value of the STP2 bit in UARTLCRH is ignored and the number of stop bits is forced to 2. Note that the UART does not support automatic retransmission on parity errors. If a parity error is detected on transmission, all further transmit operations are aborted and software must handle retransmission of the affected byte or message. 2 SIRLP R/W 0 UART SIR Low-Power Mode This bit selects the IrDA encoding mode. Value Description 1 The UART operates in SIR Low-Power mode. Low-level bits are transmitted with a pulse width which is 3 times the period of the IrLPBaud16 input signal, regardless of the selected bit rate. 0 Low-level bits are transmitted as an active High pulse with a width of 3/16th of the bit period. Setting this bit uses less power, but might reduce transmission distances. See page 940 for more information. 1 SIREN R/W 0 UART SIR Enable Value Description 0 UARTEN R/W 0 1 The IrDA SIR block is enabled, and the UART will transmit and receive data using SIR protocol. 0 Normal operation. UART Enable Value Description 1 The UART is enabled. 0 The UART is disabled. If the UART is disabled in the middle of transmission or reception, it completes the current character before stopping. 948 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 9: UART Interrupt FIFO Level Select (UARTIFLS), offset 0x034 The UARTIFLS register is the interrupt FIFO level select register. You can use this register to define the FIFO level at which the TXRIS and RXRIS bits in the UARTRIS register are triggered. The interrupts are generated based on a transition through a level rather than being based on the level. That is, the interrupts are generated when the fill level progresses through the trigger level. For example, if the receive trigger level is set to the half-way mark, the interrupt is triggered as the module is receiving the 9th character. Out of reset, the TXIFLSEL and RXIFLSEL bits are configured so that the FIFOs trigger an interrupt at the half-way mark. UART Interrupt FIFO Level Select (UARTIFLS) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x034 Type R/W, reset 0x0000.0012 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 4 3 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RXIFLSEL RO 0 Bit/Field Name Type Reset 31:6 reserved RO 0x0000.00 5:3 RXIFLSEL R/W 0x2 RO 0 RO 0 RO 0 R/W 0 R/W 1 TXIFLSEL R/W 0 R/W 0 R/W 1 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Receive Interrupt FIFO Level Select The trigger points for the receive interrupt are as follows: Value Description 0x0 RX FIFO ≥ ⅛ full 0x1 RX FIFO ≥ ¼ full 0x2 RX FIFO ≥ ½ full (default) 0x3 RX FIFO ≥ ¾ full 0x4 RX FIFO ≥ ⅞ full 0x5-0x7 Reserved November 08, 2011 949 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 2:0 TXIFLSEL R/W 0x2 Description UART Transmit Interrupt FIFO Level Select The trigger points for the transmit interrupt are as follows: Value Description 0x0 TX FIFO ≤ ⅞ empty 0x1 TX FIFO ≤ ¾ empty 0x2 TX FIFO ≤ ½ empty (default) 0x3 TX FIFO ≤ ¼ empty 0x4 TX FIFO ≤ ⅛ empty 0x5-0x7 Reserved Note: If the EOT bit in UARTCTL is set (see page 945), the transmit interrupt is generated once the FIFO is completely empty and all data including stop bits have left the transmit serializer. In this case, the setting of TXIFLSEL is ignored. 950 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 10: UART Interrupt Mask (UARTIM), offset 0x038 The UARTIM register is the interrupt mask set/clear register. On a read, this register gives the current value of the mask on the relevant interrupt. Setting a bit allows the corresponding raw interrupt signal to be routed to the interrupt controller. Clearing a bit prevents the raw interrupt signal from being sent to the interrupt controller. Note that bits [3:0] are only implemented on UART1. These bits are reserved on UART0 and UART2. UART Interrupt Mask (UARTIM) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x038 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 LME5IM LME1IM LMSBIM 9BITIM reserved OEIM BEIM PEIM FEIM RTIM TXIM RXIM DSRIM DCDIM CTSIM RIIM R/W 0 R/W 0 R/W 0 R/W 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15 LME5IM R/W 0 LIN Mode Edge 5 Interrupt Mask Value Description 14 LME1IM R/W 0 1 An interrupt is sent to the interrupt controller when the LME5RIS bit in the UARTRIS register is set. 0 The LME5RIS interrupt is suppressed and not sent to the interrupt controller. LIN Mode Edge 1 Interrupt Mask Value Description 1 An interrupt is sent to the interrupt controller when the LME1RIS bit in the UARTRIS register is set. 0 The LME1RIS interrupt is suppressed and not sent to the interrupt controller. November 08, 2011 951 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 13 LMSBIM R/W 0 Description LIN Mode Sync Break Interrupt Mask Value Description 12 9BITIM R/W 0 1 An interrupt is sent to the interrupt controller when the LMSBRIS bit in the UARTRIS register is set. 0 The LMSBRIS interrupt is suppressed and not sent to the interrupt controller. 9-Bit Mode Interrupt Mask Value Description 1 An interrupt is sent to the interrupt controller when the 9BITRIS bit in the UARTRIS register is set. 0 The 9BITRIS interrupt is suppressed and not sent to the interrupt controller. 11 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 OEIM R/W 0 UART Overrun Error Interrupt Mask Value Description 9 BEIM R/W 0 1 An interrupt is sent to the interrupt controller when the OERIS bit in the UARTRIS register is set. 0 The OERIS interrupt is suppressed and not sent to the interrupt controller. UART Break Error Interrupt Mask Value Description 8 PEIM R/W 0 1 An interrupt is sent to the interrupt controller when the BERIS bit in the UARTRIS register is set. 0 The BERIS interrupt is suppressed and not sent to the interrupt controller. UART Parity Error Interrupt Mask Value Description 1 An interrupt is sent to the interrupt controller when the PERIS bit in the UARTRIS register is set. 0 The PERIS interrupt is suppressed and not sent to the interrupt controller. 952 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 7 FEIM R/W 0 Description UART Framing Error Interrupt Mask Value Description 6 RTIM R/W 0 1 An interrupt is sent to the interrupt controller when the FERIS bit in the UARTRIS register is set. 0 The FERIS interrupt is suppressed and not sent to the interrupt controller. UART Receive Time-Out Interrupt Mask Value Description 5 TXIM R/W 0 1 An interrupt is sent to the interrupt controller when the RTRIS bit in the UARTRIS register is set. 0 The RTRIS interrupt is suppressed and not sent to the interrupt controller. UART Transmit Interrupt Mask Value Description 4 RXIM R/W 0 1 An interrupt is sent to the interrupt controller when the TXRIS bit in the UARTRIS register is set. 0 The TXRIS interrupt is suppressed and not sent to the interrupt controller. UART Receive Interrupt Mask Value Description 3 DSRIM R/W 0 1 An interrupt is sent to the interrupt controller when the RXRIS bit in the UARTRIS register is set. 0 The RXRIS interrupt is suppressed and not sent to the interrupt controller. UART Data Set Ready Modem Interrupt Mask Value Description 1 An interrupt is sent to the interrupt controller when the DSRRIS bit in the UARTRIS register is set. 0 The DSRRIS interrupt is suppressed and not sent to the interrupt controller. This bit is implemented only on UART1 and is reserved for UART0 and UART2. November 08, 2011 953 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 2 DCDIM R/W 0 Description UART Data Carrier Detect Modem Interrupt Mask Value Description 1 An interrupt is sent to the interrupt controller when the DCDRIS bit in the UARTRIS register is set. 0 The DCDRIS interrupt is suppressed and not sent to the interrupt controller. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 1 CTSIM R/W 0 UART Clear to Send Modem Interrupt Mask Value Description 1 An interrupt is sent to the interrupt controller when the CTSRIS bit in the UARTRIS register is set. 0 The CTSRIS interrupt is suppressed and not sent to the interrupt controller. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 0 RIIM R/W 0 UART Ring Indicator Modem Interrupt Mask Value Description 1 An interrupt is sent to the interrupt controller when the RIRIS bit in the UARTRIS register is set. 0 The RIRIS interrupt is suppressed and not sent to the interrupt controller. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 954 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 11: UART Raw Interrupt Status (UARTRIS), offset 0x03C The UARTRIS register is the raw interrupt status register. On a read, this register gives the current raw status value of the corresponding interrupt. A write has no effect. Note that bits [3:0] are only implemented on UART1. These bits are reserved on UART0 and UART2. UART Raw Interrupt Status (UARTRIS) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x03C Type RO, reset 0x0000.000F 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 reserved OERIS RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BERIS PERIS FERIS RTRIS TXRIS RXRIS DSRRIS DCDRIS CTSRIS RIRIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset LME5RIS LME1RIS LMSBRIS 9BITRIS Type Reset RO 0 RO 0 RO 0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15 LME5RIS RO 0 LIN Mode Edge 5 Raw Interrupt Status Value Description 1 The timer value at the 5th falling edge of the LIN Sync Field has been captured. 0 No interrupt This bit is cleared by writing a 1 to the LME5IC bit in the UARTICR register. 14 LME1RIS RO 0 LIN Mode Edge 1 Raw Interrupt Status Value Description 1 The timer value at the 1st falling edge of the LIN Sync Field has been captured. 0 No interrupt This bit is cleared by writing a 1 to the LME1IC bit in the UARTICR register. November 08, 2011 955 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 13 LMSBRIS RO 0 Description LIN Mode Sync Break Raw Interrupt Status Value Description 1 A LIN Sync Break has been detected. 0 No interrupt This bit is cleared by writing a 1 to the LMSBIC bit in the UARTICR register. 12 9BITRIS R/W 0 9-Bit Mode Raw Interrupt Status Value Description 1 A receive address match has occurred. 0 No interrupt This bit is cleared by writing a 1 to the 9BITIC bit in the UARTICR register. 11 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 OERIS RO 0 UART Overrun Error Raw Interrupt Status Value Description 1 An overrun error has occurred. 0 No interrupt This bit is cleared by writing a 1 to the OEIC bit in the UARTICR register. 9 BERIS RO 0 UART Break Error Raw Interrupt Status Value Description 1 A break error has occurred. 0 No interrupt This bit is cleared by writing a 1 to the BEIC bit in the UARTICR register. 8 PERIS RO 0 UART Parity Error Raw Interrupt Status Value Description 1 A parity error has occurred. 0 No interrupt This bit is cleared by writing a 1 to the PEIC bit in the UARTICR register. 7 FERIS RO 0 UART Framing Error Raw Interrupt Status Value Description 1 A framing error has occurred. 0 No interrupt This bit is cleared by writing a 1 to the FEIC bit in the UARTICR register. 956 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 6 RTRIS RO 0 Description UART Receive Time-Out Raw Interrupt Status Value Description 1 A receive time out has occurred. 0 No interrupt This bit is cleared by writing a 1 to the RTIC bit in the UARTICR register. 5 TXRIS RO 0 UART Transmit Raw Interrupt Status Value Description 1 If the EOT bit in the UARTCTL register is clear, the transmit FIFO level has passed through the condition defined in the UARTIFLS register. If the EOT bit is set, the last bit of all transmitted data and flags has left the serializer. 0 No interrupt This bit is cleared by writing a 1 to the TXIC bit in the UARTICR register or by writing data to the transmit FIFO until it becomes greater than the trigger level, if the FIFO is enabled, or by writing a single byte if the FIFO is disabled. 4 RXRIS RO 0 UART Receive Raw Interrupt Status Value Description 1 The receive FIFO level has passed through the condition defined in the UARTIFLS register. 0 No interrupt This bit is cleared by writing a 1 to the RXIC bit in the UARTICR register or by reading data from the receive FIFO until it becomes less than the trigger level, if the FIFO is enabled, or by reading a single byte if the FIFO is disabled. 3 DSRRIS RO 0 UART Data Set Ready Modem Raw Interrupt Status Value Description 1 Data Set Ready used for software flow control. 0 No interrupt This bit is cleared by writing a 1 to the DSRIC bit in the UARTICR register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. November 08, 2011 957 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 2 DCDRIS RO 0 Description UART Data Carrier Detect Modem Raw Interrupt Status Value Description 1 Data Carrier Detect used for software flow control. 0 No interrupt This bit is cleared by writing a 1 to the DCDIC bit in the UARTICR register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 1 CTSRIS RO 0 UART Clear to Send Modem Raw Interrupt Status Value Description 1 Clear to Send used for software flow control. 0 No interrupt This bit is cleared by writing a 1 to the CTSIC bit in the UARTICR register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 0 RIRIS RO 0 UART Ring Indicator Modem Raw Interrupt Status Value Description 1 Ring Indicator used for software flow control. 0 No interrupt This bit is cleared by writing a 1 to the RIIC bit in the UARTICR register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 958 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 12: UART Masked Interrupt Status (UARTMIS), offset 0x040 The UARTMIS register is the masked interrupt status register. On a read, this register gives the current masked status value of the corresponding interrupt. A write has no effect. Note that bits [3:0] are only implemented on UART1. These bits are reserved on UART0 and UART2. UART Masked Interrupt Status (UARTMIS) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x040 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 reserved OEMIS RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BEMIS PEMIS FEMIS RTMIS TXMIS RXMIS CTSMIS RIMIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset LME5MIS LME1MIS LMSBMIS 9BITMIS Type Reset RO 0 RO 0 RO 0 R/W 0 DSRMIS DCDMIS RO 0 RO 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15 LME5MIS RO 0 LIN Mode Edge 5 Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to the 5th falling edge of the LIN Sync Field. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the LME5IC bit in the UARTICR register. 14 LME1MIS RO 0 LIN Mode Edge 1 Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to the 1st falling edge of the LIN Sync Field. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the LME1IC bit in the UARTICR register. November 08, 2011 959 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 13 LMSBMIS RO 0 Description LIN Mode Sync Break Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to the receipt of a LIN Sync Break. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the LMSBIC bit in the UARTICR register. 12 9BITMIS R/W 0 9-Bit Mode Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to a receive address match. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the 9BITIC bit in the UARTICR register. 11 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 OEMIS RO 0 UART Overrun Error Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to an overrun error. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the OEIC bit in the UARTICR register. 9 BEMIS RO 0 UART Break Error Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to a break error. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the BEIC bit in the UARTICR register. 8 PEMIS RO 0 UART Parity Error Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to a parity error. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the PEIC bit in the UARTICR register. 7 FEMIS RO 0 UART Framing Error Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to a framing error. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the FEIC bit in the UARTICR register. 960 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 6 RTMIS RO 0 Description UART Receive Time-Out Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to a receive time out. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the RTIC bit in the UARTICR register. 5 TXMIS RO 0 UART Transmit Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to passing through the specified transmit FIFO level (if the EOT bit is clear) or due to the transmission of the last data bit (if the EOT bit is set). 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the TXIC bit in the UARTICR register or by writing data to the transmit FIFO until it becomes greater than the trigger level, if the FIFO is enabled, or by writing a single byte if the FIFO is disabled. 4 RXMIS RO 0 UART Receive Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to passing through the specified receive FIFO level. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the RXIC bit in the UARTICR register or by reading data from the receive FIFO until it becomes less than the trigger level, if the FIFO is enabled, or by reading a single byte if the FIFO is disabled. 3 DSRMIS RO 0 UART Data Set Ready Modem Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to Data Set Ready. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the DSRIC bit in the UARTICR register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 2 DCDMIS RO 0 UART Data Carrier Detect Modem Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to Data Carrier Detect. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the DCDIC bit in the UARTICR register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. November 08, 2011 961 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 1 CTSMIS RO 0 Description UART Clear to Send Modem Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to Clear to Send. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the CTSIC bit in the UARTICR register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 0 RIMIS RO 0 UART Ring Indicator Modem Masked Interrupt Status Value Description 1 An unmasked interrupt was signaled due to Ring Indicator. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the RIIC bit in the UARTICR register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 962 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 13: UART Interrupt Clear (UARTICR), offset 0x044 The UARTICR register is the interrupt clear register. On a write of 1, the corresponding interrupt (both raw interrupt and masked interrupt, if enabled) is cleared. A write of 0 has no effect. Note that bits [3:0] are only implemented on UART1. These bits are reserved on UART0 and UART2. UART Interrupt Clear (UARTICR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x044 Type W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 LME5IC LME1IC LMSBIC 9BITIC reserved OEIC W1C 0 W1C 0 W1C 0 R/W 0 RO 0 W1C 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BEIC PEIC FEIC RTIC TXIC RXIC W1C 0 W1C 0 W1C 0 W1C 0 W1C 0 W1C 0 reserved Type Reset Type Reset DSRMIC DCDMIC CTSMIC W1C 0 W1C 0 W1C 0 RIMIC W1C 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15 LME5IC W1C 0 LIN Mode Edge 5 Interrupt Clear Writing a 1 to this bit clears the LME5RIS bit in the UARTRIS register and the LME5MIS bit in the UARTMIS register. 14 LME1IC W1C 0 LIN Mode Edge 1 Interrupt Clear Writing a 1 to this bit clears the LME1RIS bit in the UARTRIS register and the LME1MIS bit in the UARTMIS register. 13 LMSBIC W1C 0 LIN Mode Sync Break Interrupt Clear Writing a 1 to this bit clears the LMSBRIS bit in the UARTRIS register and the LMSBMIS bit in the UARTMIS register. 12 9BITIC R/W 0 9-Bit Mode Interrupt Clear Writing a 1 to this bit clears the 9BITRIS bit in the UARTRIS register and the 9BITMIS bit in the UARTMIS register. 11 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 OEIC W1C 0 Overrun Error Interrupt Clear Writing a 1 to this bit clears the OERIS bit in the UARTRIS register and the OEMIS bit in the UARTMIS register. November 08, 2011 963 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 9 BEIC W1C 0 Description Break Error Interrupt Clear Writing a 1 to this bit clears the BERIS bit in the UARTRIS register and the BEMIS bit in the UARTMIS register. 8 PEIC W1C 0 Parity Error Interrupt Clear Writing a 1 to this bit clears the PERIS bit in the UARTRIS register and the PEMIS bit in the UARTMIS register. 7 FEIC W1C 0 Framing Error Interrupt Clear Writing a 1 to this bit clears the FERIS bit in the UARTRIS register and the FEMIS bit in the UARTMIS register. 6 RTIC W1C 0 Receive Time-Out Interrupt Clear Writing a 1 to this bit clears the RTRIS bit in the UARTRIS register and the RTMIS bit in the UARTMIS register. 5 TXIC W1C 0 Transmit Interrupt Clear Writing a 1 to this bit clears the TXRIS bit in the UARTRIS register and the TXMIS bit in the UARTMIS register. 4 RXIC W1C 0 Receive Interrupt Clear Writing a 1 to this bit clears the RXRIS bit in the UARTRIS register and the RXMIS bit in the UARTMIS register. 3 DSRMIC W1C 0 UART Data Set Ready Modem Interrupt Clear Writing a 1 to this bit clears the DSRRIS bit in the UARTRIS register and the DSRMIS bit in the UARTMIS register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 2 DCDMIC W1C 0 UART Data Carrier Detect Modem Interrupt Clear Writing a 1 to this bit clears the DCDRIS bit in the UARTRIS register and the DCDMIS bit in the UARTMIS register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 1 CTSMIC W1C 0 UART Clear to Send Modem Interrupt Clear Writing a 1 to this bit clears the CTSRIS bit in the UARTRIS register and the CTSMIS bit in the UARTMIS register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 0 RIMIC W1C 0 UART Ring Indicator Modem Interrupt Clear Writing a 1 to this bit clears the RIRIS bit in the UARTRIS register and the RIMIS bit in the UARTMIS register. This bit is implemented only on UART1 and is reserved for UART0 and UART2. 964 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 14: UART DMA Control (UARTDMACTL), offset 0x048 The UARTDMACTL register is the DMA control register. UART DMA Control (UARTDMACTL) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x048 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type 31:3 reserved RO 2 DMAERR R/W RO 0 Reset DMAERR TXDMAE RXDMAE RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 Description 0x00000.000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 DMA on Error Value Description 1 TXDMAE R/W 0 1 µDMA receive requests are automatically disabled when a receive error occurs. 0 µDMA receive requests are unaffected when a receive error occurs. Transmit DMA Enable Value Description 0 RXDMAE R/W 0 1 µDMA for the transmit FIFO is enabled. 0 µDMA for the transmit FIFO is disabled. Receive DMA Enable Value Description 1 µDMA for the receive FIFO is enabled. 0 µDMA for the receive FIFO is disabled. November 08, 2011 965 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 15: UART LIN Control (UARTLCTL), offset 0x090 The UARTLCTL register is the configures the operation of the UART when in LIN mode. UART LIN Control (UARTLCTL) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x090 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 BLEN RO 0 Bit/Field Name Type Reset 31:6 reserved RO 0x0000.00 5:4 BLEN R/W 0x0 RO 0 RO 0 RO 0 R/W 0 reserved R/W 0 RO 0 RO 0 0 MASTER RO 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Sync Break Length Value Description 3:1 reserved RO 0x0 0 MASTER R/W 0 0x3 Sync break length is 16T bits 0x2 Sync break length is 15T bits 0x1 Sync break length is 14T bits 0x0 Sync break length is 13T bits (default) Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. LIN Master Enable Value Description 1 The UART operates as a LIN master. 0 The UART operates as a LIN slave. 966 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 16: UART LIN Snap Shot (UARTLSS), offset 0x094 The UARTLSS register captures the free-running timer value when either the Sync Edge 1 or the Sync Edge 5 is detected in LIN mode. UART LIN Snap Shot (UARTLSS) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x094 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 TSS Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 TSS RO 0x0000 Timer Snap Shot This field contains the value of the free-running timer when either the Sync Edge 5 or the Sync Edge 1 was detected. November 08, 2011 967 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 17: UART LIN Timer (UARTLTIM), offset 0x098 The UARTLTIM register contains the current timer value for the free-running timer that is used to calculate the baud rate when in LIN slave mode. The value in this register is used along with the value in the UART LIN Snap Shot (UARTLSS) register to adjust the baud rate to match that of the master. UART LIN Timer (UARTLTIM) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x098 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 TIMER Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 TIMER RO 0x0000 Timer Value This field contains the value of the free-running timer. 968 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 18: UART 9-Bit Self Address (UART9BITADDR), offset 0x0A4 The UART9BITADDR register is used to write the specific address that should be matched with the receiving byte when the 9-bit Address Mask (UART9BITAMASK) is set to 0xFF. This register is used in conjunction with UART9BITAMASK to form a match for address-byte received. UART 9-Bit Self Address (UART9BITADDR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x0A4 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 15 14 13 12 9BITEN Type Reset R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 11 10 9 8 7 6 5 4 reserved RO 0 RO 0 RO 0 RO 0 ADDR RO 0 RO 0 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15 9BITEN R/W 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Enable 9-Bit Mode Value Description 1 9-bit mode is enabled. 0 9-bit mode is disabled. 14:8 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 ADDR R/W 0x00 Self Address for 9-Bit Mode This field contains the address that should be matched when UART9BITAMASK is 0xFF. November 08, 2011 969 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 19: UART 9-Bit Self Address Mask (UART9BITAMASK), offset 0x0A8 The UART9BITAMASK register is used to enable the address mask for 9-bit mode. The lower address bits are masked to create a range of address to be matched with the received address byte. UART 9-Bit Self Address Mask (UART9BITAMASK) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0x0A8 Type R/W, reset 0x0000.00FF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 RANGE Type Reset RO 0 RO 0 RO 0 RO 0 MASK RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15:8 RANGE RO 0x00 RO 0 R/W 1 R/W 1 R/W 1 R/W 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Self Address Range for 9-Bit Mode Writing to the RANGE field does not have any effect; reading it reflects the ANDed output of the ADDR field in the UART9BITADDR register and the MASK field. 7:0 MASK R/W 0xFF Self Address Mask for 9-Bit Mode This field contains the address mask that creates a range of addresses that should be matched. 970 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 20: UART Peripheral Properties (UARTPP), offset 0xFC0 The UARTPP register provides information regarding the properties of the UART module. UART Peripheral Properties (UARTPP) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFC0 Type RO, reset 0x0000.0003 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1 NB RO 0x1 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 NB SC RO 1 RO 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 9-Bit Support Value Description 0 SC RO 0x1 1 The UART module provides support for the transmission of 9-bit data for RS-485 support. 0 The UART module does not provide support for the transmission of 9-bit data for RS-485 support. Smart Card Support Value Description 1 The UART module provides smart card support. 0 The UART module does not provide smart card support. November 08, 2011 971 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 21: UART Clock Configuration (UARTCC), offset 0xFC8 The UARTCC register controls the baud clock source for the UART module. For more information, see the section called “Communication Clock Sources” on page 224. Note: If the PIOSC is used for the UART baud clock, the system clock frequency must be at least 9 MHz in Run mode. UART Clock Configuration (UARTCC) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFC8 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset CS Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3:0 CS R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Baud Clock Source The following table specifies the clock source that generates the baud clock for the UART. Value Description 0x0 The system clock (default). 0x1 PIOSC 0x2 - 0xF Reserved 972 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 22: UART Peripheral Identification 4 (UARTPeriphID4), offset 0xFD0 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 4 (UARTPeriphID4) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFD0 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID4 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID4 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register [7:0] Can be used by software to identify the presence of this peripheral. November 08, 2011 973 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 23: UART Peripheral Identification 5 (UARTPeriphID5), offset 0xFD4 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 5 (UARTPeriphID5) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFD4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID5 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID5 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register [15:8] Can be used by software to identify the presence of this peripheral. 974 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 24: UART Peripheral Identification 6 (UARTPeriphID6), offset 0xFD8 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 6 (UARTPeriphID6) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFD8 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID6 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID6 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register [23:16] Can be used by software to identify the presence of this peripheral. November 08, 2011 975 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 25: UART Peripheral Identification 7 (UARTPeriphID7), offset 0xFDC The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 7 (UARTPeriphID7) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFDC Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID7 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID7 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register [31:24] Can be used by software to identify the presence of this peripheral. 976 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 26: UART Peripheral Identification 0 (UARTPeriphID0), offset 0xFE0 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 0 (UARTPeriphID0) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFE0 Type RO, reset 0x0000.0060 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID0 RO 0x60 RO 0 RO 0 RO 1 RO 1 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register [7:0] Can be used by software to identify the presence of this peripheral. November 08, 2011 977 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 27: UART Peripheral Identification 1 (UARTPeriphID1), offset 0xFE4 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 1 (UARTPeriphID1) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFE4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID1 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID1 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register [15:8] Can be used by software to identify the presence of this peripheral. 978 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 28: UART Peripheral Identification 2 (UARTPeriphID2), offset 0xFE8 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 2 (UARTPeriphID2) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFE8 Type RO, reset 0x0000.0018 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 1 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID2 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID2 RO 0x18 RO 0 RO 0 RO 0 RO 0 RO 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register [23:16] Can be used by software to identify the presence of this peripheral. November 08, 2011 979 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 29: UART Peripheral Identification 3 (UARTPeriphID3), offset 0xFEC The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 3 (UARTPeriphID3) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFEC Type RO, reset 0x0000.0001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID3 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID3 RO 0x01 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register [31:24] Can be used by software to identify the presence of this peripheral. 980 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 30: UART PrimeCell Identification 0 (UARTPCellID0), offset 0xFF0 The UARTPCellIDn registers are hard-coded and the fields within the registers determine the reset values. UART PrimeCell Identification 0 (UARTPCellID0) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFF0 Type RO, reset 0x0000.000D 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 1 RO 1 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CID0 RO 0x0D RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART PrimeCell ID Register [7:0] Provides software a standard cross-peripheral identification system. November 08, 2011 981 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 31: UART PrimeCell Identification 1 (UARTPCellID1), offset 0xFF4 The UARTPCellIDn registers are hard-coded and the fields within the registers determine the reset values. UART PrimeCell Identification 1 (UARTPCellID1) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFF4 Type RO, reset 0x0000.00F0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID1 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CID1 RO 0xF0 RO 0 RO 1 RO 1 RO 1 RO 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART PrimeCell ID Register [15:8] Provides software a standard cross-peripheral identification system. 982 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 32: UART PrimeCell Identification 2 (UARTPCellID2), offset 0xFF8 The UARTPCellIDn registers are hard-coded and the fields within the registers determine the reset values. UART PrimeCell Identification 2 (UARTPCellID2) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFF8 Type RO, reset 0x0000.0005 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 1 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID2 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CID2 RO 0x05 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART PrimeCell ID Register [23:16] Provides software a standard cross-peripheral identification system. November 08, 2011 983 Texas Instruments-Advance Information Universal Asynchronous Receivers/Transmitters (UARTs) Register 33: UART PrimeCell Identification 3 (UARTPCellID3), offset 0xFFC The UARTPCellIDn registers are hard-coded and the fields within the registers determine the reset values. UART PrimeCell Identification 3 (UARTPCellID3) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 Offset 0xFFC Type RO, reset 0x0000.00B1 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID3 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CID3 RO 0xB1 RO 0 RO 1 RO 0 RO 1 RO 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART PrimeCell ID Register [31:24] Provides software a standard cross-peripheral identification system. 984 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 15 Synchronous Serial Interface (SSI) ® The Stellaris microcontroller includes four Synchronous Serial Interface (SSI) modules. Each SSIis a master or slave interface for synchronous serial communication with peripheral devices that have either Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces. The Stellaris LM4F232H5BB controller includes four SSI modules with the following features: ■ Programmable interface operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces ■ Master or slave operation ■ Programmable clock bit rate and prescaler ■ Separate transmit and receive FIFOs, each 16 bits wide and 8 locations deep ■ Programmable data frame size from 4 to 16 bits ■ Internal loopback test mode for diagnostic/debug testing ■ Standard FIFO-based interrupts and End-of-Transmission interrupt ■ Efficient transfers using Micro Direct Memory Access Controller (µDMA) – Separate channels for transmit and receive – Receive single request asserted when data is in the FIFO; burst request asserted when FIFO contains 4 entries – Transmit single request asserted when there is space in the FIFO; burst request asserted when FIFO contains 4 entries November 08, 2011 985 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) 15.1 Block Diagram Figure 15-1. SSI Module Block Diagram DMA Request DMA Control SSIDMACTL Interrupt Interrupt Control TxFIFO 8 x 16 SSIIM SSIMIS SSIRIS SSIICR . . . Control/Status SSITx SSICR0 SSICR1 SSISR SSIRx Transmit/ Receive Logic SSIDR RxFIFO 8 x 16 Clock Prescaler System Clock SSIClk SSIFss . . . Clock Control SSICPSR SSIDMACTL PIOSC SSI Baud Clock Identification Registers SSIPCellID0 SSIPCellID1 SSIPCellID2 SSIPCellID3 15.2 SSIPeriphID0 SSIPeriphID1 SSIPeriphID2 SSIPeriphID3 SSIPeriphID4 SSIPeriphID5 SSIPeriphID6 SSIPeriphID7 Signal Description The following table lists the external signals of the SSI module and describes the function of each. The SSI signals are alternate functions for some GPIO signals and default to be GPIO signals at reset., with the exception of the SSI0Clk, SSI0Fss, SSI0Rx, and SSI0Tx pins which default to the SSI function. The column in the table below titled "Pin Mux/Pin Assignment" lists the possible GPIO pin placements for the SSI signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 698) should be set to choose the SSI function. The number in parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control 986 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller (GPIOPCTL) register (page 717) to assign the SSI signal to the specified GPIO port pin. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 674. Table 15-1. SSI Signals (157BGA) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type PA2 (2) I/O TTL Description SSI0Clk M2 SSI module 0 clock. SSI0Fss M3 PA3 (2) I/O TTL SSI module 0 frame. SSI0Rx L4 PA4 (2) I TTL SSI module 0 receive. SSI0Tx N1 PA5 (2) O TTL SSI module 0 transmit. SSI1Clk B2 L10 PD0 (2) PF2 (2) I/O TTL SSI module 1 clock. SSI1Fss B1 K10 PD1 (2) PF3 (2) I/O TTL SSI module 1 frame. SSI1Rx C2 M9 PD2 (2) PF0 (2) I TTL SSI module 1 receive. SSI1Tx C1 N9 PD3 (2) PF1 (2) O TTL SSI module 1 transmit. SSI2Clk B6 J3 PB4 (2) PH4 (2) I/O TTL SSI module 2 clock. SSI2Fss A6 H4 PB5 (2) PH5 (2) I/O TTL SSI module 2 frame. SSI2Rx F4 H3 PB6 (2) PH6 (2) I TTL SSI module 2 receive. SSI2Tx F3 G4 PB7 (2) PH7 (2) O TTL SSI module 2 transmit. SSI3Clk B2 K3 G2 PD0 (1) PH0 (2) PK0 (2) I/O TTL SSI module 3 clock. SSI3Fss B1 K4 G1 PD1 (1) PH1 (2) PK1 (2) I/O TTL SSI module 3 frame. SSI3Rx C2 J4 H1 PD2 (1) PH2 (2) PK2 (2) I TTL SSI module 3 receive. SSI3Tx C1 J2 H2 PD3 (1) PH3 (2) PK3 (2) O TTL SSI module 3 transmit. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 15.3 Functional Description The SSI performs serial-to-parallel conversion on data received from a peripheral device. The CPU accesses data, control, and status information. The transmit and receive paths are buffered with internal FIFO memories allowing up to eight 16-bit values to be stored independently in both transmit and receive modes. The SSI also supports the µDMA interface. The transmit and receive FIFOs can be programmed as destination/source addresses in the µDMA module. µDMA operation is enabled by setting the appropriate bit(s) in the SSIDMACTL register (see page 1014). November 08, 2011 987 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) 15.3.1 Bit Rate Generation The SSI includes a programmable bit rate clock divider and prescaler to generate the serial output clock. Bit rates are supported to 2 MHz and higher, although maximum bit rate is determined by peripheral devices. The serial bit rate is derived by dividing down the input clock (SysClk). The clock is first divided by an even prescale value CPSDVSR from 2 to 254, which is programmed in the SSI Clock Prescale (SSICPSR) register (see page 1007). The clock is further divided by a value from 1 to 256, which is 1 + SCR, where SCR is the value programmed in the SSI Control 0 (SSICR0) register (see page 1000). The frequency of the output clock SSIClk is defined by: SSIClk = SysClk / (CPSDVSR * (1 + SCR)) Note: The PIOSC is used as the source for the SSIClk when the CS field in the SSI Clock Configuration (SSICC) register is configured to 0x1. For master mode, the system clock or the PIOSC must be at least two times faster than the SSIClk, with the restriction that SSIClk cannot be faster than 25 MHz. For slave mode, the system clockor the PIOSC must be at least 6 times faster than the SSIClk. See “Synchronous Serial Interface (SSI)” on page 1425 to view SSI timing parameters. 15.3.2 FIFO Operation 15.3.2.1 Transmit FIFO The common transmit FIFO is a 16-bit wide, 8-locations deep, first-in, first-out memory buffer. The CPU writes data to the FIFO by writing the SSI Data (SSIDR) register (see page 1004), and data is stored in the FIFO until it is read out by the transmission logic. When configured as a master or a slave, parallel data is written into the transmit FIFO prior to serial conversion and transmission to the attached slave or master, respectively, through the SSITx pin. In slave mode, the SSI transmits data each time the master initiates a transaction. If the transmit FIFO is empty and the master initiates, the slave transmits the 8th most recent value in the transmit FIFO. If less than 8 values have been written to the transmit FIFO since the SSI module clock was enabled using the SSI bit in the RGCG1 register, then 0 is transmitted. Care should be taken to ensure that valid data is in the FIFO as needed. The SSI can be configured to generate an interrupt or a µDMA request when the FIFO is empty. 15.3.2.2 Receive FIFO The common receive FIFO is a 16-bit wide, 8-locations deep, first-in, first-out memory buffer. Received data from the serial interface is stored in the buffer until read out by the CPU, which accesses the read FIFO by reading the SSIDR register. When configured as a master or slave, serial data received through the SSIRx pin is registered prior to parallel loading into the attached slave or master receive FIFO, respectively. 15.3.3 Interrupts The SSI can generate interrupts when the following conditions are observed: ■ Transmit FIFO service (when the transmit FIFO is half full or less) ■ Receive FIFO service (when the receive FIFO is half full or more) ■ Receive FIFO time-out 988 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Receive FIFO overrun ■ End of transmission All of the interrupt events are ORed together before being sent to the interrupt controller, so the SSI generates a single interrupt request to the controller regardless of the number of active interrupts. Each of the four individual maskable interrupts can be masked by clearing the appropriate bit in the SSI Interrupt Mask (SSIIM) register (see page 1008). Setting the appropriate mask bit enables the interrupt. The individual outputs, along with a combined interrupt output, allow use of either a global interrupt service routine or modular device drivers to handle interrupts. The transmit and receive dynamic dataflow interrupts have been separated from the status interrupts so that data can be read or written in response to the FIFO trigger levels. The status of the individual interrupt sources can be read from the SSI Raw Interrupt Status (SSIRIS) and SSI Masked Interrupt Status (SSIMIS) registers (see page 1009 and page 1011, respectively). The receive FIFO has a time-out period that is 32 periods at the rate of SSIClk (whether or not SSIClk is currently active) and is started when the RX FIFO goes from EMPTY to not-EMPTY. If the RX FIFO is emptied before 32 clocks have passed, the time-out period is reset. As a result, the ISR should clear the Receive FIFO Time-out Interrupt just after reading out the RX FIFO by writing a 1 to the RTIC bit in the SSI Interrupt Clear (SSIICR) register. The interrupt should not be cleared so late that the ISR returns before the interrupt is actually cleared, or the ISR may be re-activated unnecessarily. The End-of-Transmission (EOT) interrupt indicates that the data has been transmitted completely. This interrupt can be used to indicate when it is safe to turn off the SSI module clock or enter sleep mode. In addition, because transmitted data and received data complete at exactly the same time, the interrupt can also indicate that read data is ready immediately, without waiting for the receive FIFO time-out period to complete. 15.3.4 Frame Formats Each data frame is between 4 and 16 bits long, depending on the size of data programmed, and is transmitted starting with the MSB. There are three basic frame types that can be selected: ■ Texas Instruments synchronous serial ■ Freescale SPI ■ MICROWIRE For all three formats, the serial clock (SSIClk) is held inactive while the SSI is idle, and SSIClk transitions at the programmed frequency only during active transmission or reception of data. The idle state of SSIClk is utilized to provide a receive timeout indication that occurs when the receive FIFO still contains data after a timeout period. For Freescale SPI and MICROWIRE frame formats, the serial frame (SSIFss) pin is active Low, and is asserted (pulled down) during the entire transmission of the frame. For Texas Instruments synchronous serial frame format, the SSIFss pin is pulsed for one serial clock period starting at its rising edge, prior to the transmission of each frame. For this frame format, both the SSI and the off-chip slave device drive their output data on the rising edge of SSIClk and latch data from the other device on the falling edge. Unlike the full-duplex transmission of the other two frame formats, the MICROWIRE format uses a special master-slave messaging technique which operates at half-duplex. In this mode, when a November 08, 2011 989 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) frame begins, an 8-bit control message is transmitted to the off-chip slave. During this transmit, no incoming data is received by the SSI. After the message has been sent, the off-chip slave decodes it and, after waiting one serial clock after the last bit of the 8-bit control message has been sent, responds with the requested data. The returned data can be 4 to 16 bits in length, making the total frame length anywhere from 13 to 25 bits. 15.3.4.1 Texas Instruments Synchronous Serial Frame Format Figure 15-2 on page 990 shows the Texas Instruments synchronous serial frame format for a single transmitted frame. Figure 15-2. TI Synchronous Serial Frame Format (Single Transfer) SSIClk SSIFss SSITx/SSIRx MSB LSB 4 to 16 bits In this mode, SSIClk and SSIFss are forced Low, and the transmit data line SSITx is tristated whenever the SSI is idle. Once the bottom entry of the transmit FIFO contains data, SSIFss is pulsed High for one SSIClk period. The value to be transmitted is also transferred from the transmit FIFO to the serial shift register of the transmit logic. On the next rising edge of SSIClk, the MSB of the 4 to 16-bit data frame is shifted out on the SSITx pin. Likewise, the MSB of the received data is shifted onto the SSIRx pin by the off-chip serial slave device. Both the SSI and the off-chip serial slave device then clock each data bit into their serial shifter on each falling edge of SSIClk. The received data is transferred from the serial shifter to the receive FIFO on the first rising edge of SSIClk after the LSB has been latched. Figure 15-3 on page 990 shows the Texas Instruments synchronous serial frame format when back-to-back frames are transmitted. Figure 15-3. TI Synchronous Serial Frame Format (Continuous Transfer) SSIClk SSIFss SSITx/SSIRx MSB LSB 4 to 16 bits 990 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 15.3.4.2 Freescale SPI Frame Format The Freescale SPI interface is a four-wire interface where the SSIFss signal behaves as a slave select. The main feature of the Freescale SPI format is that the inactive state and phase of the SSIClk signal are programmable through the SPO and SPH bits in the SSISCR0 control register. SPO Clock Polarity Bit When the SPO clock polarity control bit is clear, it produces a steady state Low value on the SSIClk pin. If the SPO bit is set, a steady state High value is placed on the SSIClk pin when data is not being transferred. SPH Phase Control Bit The SPH phase control bit selects the clock edge that captures data and allows it to change state. The state of this bit has the most impact on the first bit transmitted by either allowing or not allowing a clock transition before the first data capture edge. When the SPH phase control bit is clear, data is captured on the first clock edge transition. If the SPH bit is set, data is captured on the second clock edge transition. 15.3.4.3 Freescale SPI Frame Format with SPO=0 and SPH=0 Single and continuous transmission signal sequences for Freescale SPI format with SPO=0 and SPH=0 are shown in Figure 15-4 on page 991 and Figure 15-5 on page 991. Figure 15-4. Freescale SPI Format (Single Transfer) with SPO=0 and SPH=0 SSIClk SSIFss SSIRx LSB MSB Q 4 to 16 bits SSITx MSB Note: LSB Q is undefined. Figure 15-5. Freescale SPI Format (Continuous Transfer) with SPO=0 and SPH=0 SSIClk SSIFss SSIRx LSB LSB MSB MSB 4 to16 bits SSITx LSB MSB LSB MSB In this configuration, during idle periods: ■ SSIClk is forced Low November 08, 2011 991 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low ■ When the SSI is configured as a master, it enables the SSIClk pad ■ When the SSI is configured as a slave, it disables the SSIClk pad If the SSI is enabled and valid data is in the transmit FIFO, the start of transmission is signified by the SSIFss master signal being driven Low, causing slave data to be enabled onto the SSIRx input line of the master. The master SSITx output pad is enabled. One half SSIClk period later, valid master data is transferred to the SSITx pin. Once both the master and slave data have been set, the SSIClk master clock pin goes High after one additional half SSIClk period. The data is now captured on the rising and propagated on the falling edges of the SSIClk signal. In the case of a single word transmission, after all bits of the data word have been transferred, the SSIFss line is returned to its idle High state one SSIClk period after the last bit has been captured. However, in the case of continuous back-to-back transmissions, the SSIFss signal must be pulsed High between each data word transfer because the slave select pin freezes the data in its serial peripheral register and does not allow it to be altered if the SPH bit is clear. Therefore, the master device must raise the SSIFss pin of the slave device between each data transfer to enable the serial peripheral data write. On completion of the continuous transfer, the SSIFss pin is returned to its idle state one SSIClk period after the last bit has been captured. 15.3.4.4 Freescale SPI Frame Format with SPO=0 and SPH=1 The transfer signal sequence for Freescale SPI format with SPO=0 and SPH=1 is shown in Figure 15-6 on page 992, which covers both single and continuous transfers. Figure 15-6. Freescale SPI Frame Format with SPO=0 and SPH=1 SSIClk SSIFss SSIRx Q Q MSB LSB Q 4 to 16 bits SSITx LSB MSB Note: Q is undefined. In this configuration, during idle periods: ■ SSIClk is forced Low ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low ■ When the SSI is configured as a master, it enables the SSIClk pad 992 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ When the SSI is configured as a slave, it disables the SSIClk pad If the SSI is enabled and valid data is in the transmit FIFO, the start of transmission is signified by the SSIFss master signal being driven Low. The master SSITx output is enabled. After an additional one-half SSIClk period, both master and slave valid data are enabled onto their respective transmission lines. At the same time, the SSIClk is enabled with a rising edge transition. Data is then captured on the falling edges and propagated on the rising edges of the SSIClk signal. In the case of a single word transfer, after all bits have been transferred, the SSIFss line is returned to its idle High state one SSIClk period after the last bit has been captured. For continuous back-to-back transfers, the SSIFss pin is held Low between successive data words, and termination is the same as that of the single word transfer. 15.3.4.5 Freescale SPI Frame Format with SPO=1 and SPH=0 Single and continuous transmission signal sequences for Freescale SPI format with SPO=1 and SPH=0 are shown in Figure 15-7 on page 993 and Figure 15-8 on page 993. Figure 15-7. Freescale SPI Frame Format (Single Transfer) with SPO=1 and SPH=0 SSIClk SSIFss SSIRx MSB LSB Q 4 to 16 bits SSITx LSB MSB Note: Q is undefined. Figure 15-8. Freescale SPI Frame Format (Continuous Transfer) with SPO=1 and SPH=0 SSIClk SSIFss SSITx/SSIRx MSB LSB LSB MSB 4 to 16 bits In this configuration, during idle periods: ■ SSIClk is forced High ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low ■ When the SSI is configured as a master, it enables the SSIClk pad ■ When the SSI is configured as a slave, it disables the SSIClk pad November 08, 2011 993 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) If the SSI is enabled and valid data is in the transmit FIFO, the start of transmission is signified by the SSIFss master signal being driven Low, causing slave data to be immediately transferred onto the SSIRx line of the master. The master SSITx output pad is enabled. One-half period later, valid master data is transferred to the SSITx line. Once both the master and slave data have been set, the SSIClk master clock pin becomes Low after one additional half SSIClk period, meaning that data is captured on the falling edges and propagated on the rising edges of the SSIClk signal. In the case of a single word transmission, after all bits of the data word are transferred, the SSIFss line is returned to its idle High state one SSIClk period after the last bit has been captured. However, in the case of continuous back-to-back transmissions, the SSIFss signal must be pulsed High between each data word transfer because the slave select pin freezes the data in its serial peripheral register and does not allow it to be altered if the SPH bit is clear. Therefore, the master device must raise the SSIFss pin of the slave device between each data transfer to enable the serial peripheral data write. On completion of the continuous transfer, the SSIFss pin is returned to its idle state one SSIClk period after the last bit has been captured. 15.3.4.6 Freescale SPI Frame Format with SPO=1 and SPH=1 The transfer signal sequence for Freescale SPI format with SPO=1 and SPH=1 is shown in Figure 15-9 on page 994, which covers both single and continuous transfers. Figure 15-9. Freescale SPI Frame Format with SPO=1 and SPH=1 SSIClk SSIFss SSIRx Q MSB LSB Q 4 to 16 bits MSB SSITx Note: LSB Q is undefined. In this configuration, during idle periods: ■ SSIClk is forced High ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low ■ When the SSI is configured as a master, it enables the SSIClk pad ■ When the SSI is configured as a slave, it disables the SSIClk pad If the SSI is enabled and valid data is in the transmit FIFO, the start of transmission is signified by the SSIFss master signal being driven Low. The master SSITx output pad is enabled. After an additional one-half SSIClk period, both master and slave data are enabled onto their respective transmission lines. At the same time, SSIClk is enabled with a falling edge transition. Data is then captured on the rising edges and propagated on the falling edges of the SSIClk signal. 994 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller After all bits have been transferred, in the case of a single word transmission, the SSIFss line is returned to its idle high state one SSIClk period after the last bit has been captured. For continuous back-to-back transmissions, the SSIFss pin remains in its active Low state until the final bit of the last word has been captured and then returns to its idle state as described above. For continuous back-to-back transfers, the SSIFss pin is held Low between successive data words and termination is the same as that of the single word transfer. 15.3.4.7 MICROWIRE Frame Format Figure 15-10 on page 995 shows the MICROWIRE frame format for a single frame. Figure 15-11 on page 996 shows the same format when back-to-back frames are transmitted. Figure 15-10. MICROWIRE Frame Format (Single Frame) SSIClk SSIFss SSITx LSB MSB 8-bit control 0 SSIRx MSB LSB 4 to 16 bits output data MICROWIRE format is very similar to SPI format, except that transmission is half-duplex instead of full-duplex and uses a master-slave message passing technique. Each serial transmission begins with an 8-bit control word that is transmitted from the SSI to the off-chip slave device. During this transmission, no incoming data is received by the SSI. After the message has been sent, the off-chip slave decodes it and, after waiting one serial clock after the last bit of the 8-bit control message has been sent, responds with the required data. The returned data is 4 to 16 bits in length, making the total frame length anywhere from 13 to 25 bits. In this configuration, during idle periods: ■ SSIClk is forced Low ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low A transmission is triggered by writing a control byte to the transmit FIFO. The falling edge of SSIFss causes the value contained in the bottom entry of the transmit FIFO to be transferred to the serial shift register of the transmit logic and the MSB of the 8-bit control frame to be shifted out onto the SSITx pin. SSIFss remains Low for the duration of the frame transmission. The SSIRx pin remains tristated during this transmission. The off-chip serial slave device latches each control bit into its serial shifter on each rising edge of SSIClk. After the last bit is latched by the slave device, the control byte is decoded during a one clock wait-state, and the slave responds by transmitting data back to the SSI. Each bit is driven onto the SSIRx line on the falling edge of SSIClk. The SSI in turn latches each bit on the rising edge of SSIClk. At the end of the frame, for single transfers, the SSIFss signal is pulled High one clock period after the last bit has been latched in the receive serial shifter, causing the data to be transferred to the receive FIFO. November 08, 2011 995 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Note: The off-chip slave device can tristate the receive line either on the falling edge of SSIClk after the LSB has been latched by the receive shifter or when the SSIFss pin goes High. For continuous transfers, data transmission begins and ends in the same manner as a single transfer. However, the SSIFss line is continuously asserted (held Low) and transmission of data occurs back-to-back. The control byte of the next frame follows directly after the LSB of the received data from the current frame. Each of the received values is transferred from the receive shifter on the falling edge of SSIClk, after the LSB of the frame has been latched into the SSI. Figure 15-11. MICROWIRE Frame Format (Continuous Transfer) SSIClk SSIFss SSITx LSB MSB LSB 8-bit control SSIRx 0 MSB MSB LSB 4 to 16 bits output data In the MICROWIRE mode, the SSI slave samples the first bit of receive data on the rising edge of SSIClk after SSIFss has gone Low. Masters that drive a free-running SSIClk must ensure that the SSIFss signal has sufficient setup and hold margins with respect to the rising edge of SSIClk. Figure 15-12 on page 996 illustrates these setup and hold time requirements. With respect to the SSIClk rising edge on which the first bit of receive data is to be sampled by the SSI slave, SSIFss must have a setup of at least two times the period of SSIClk on which the SSI operates. With respect to the SSIClk rising edge previous to this edge, SSIFss must have a hold of at least one SSIClk period. Figure 15-12. MICROWIRE Frame Format, SSIFss Input Setup and Hold Requirements tSetup=(2*tSSIClk) tHold=tSSIClk SSIClk SSIFss SSIRx First RX data to be sampled by SSI slave 15.3.5 DMA Operation The SSI peripheral provides an interface to the μDMA controller with separate channels for transmit and receive. The µDMA operation of the SSI is enabled through the SSI DMA Control (SSIDMACTL) register. When µDMA operation is enabled, the SSI asserts a µDMA request on the receive or transmit channel when the associated FIFO can transfer data. For the receive channel, a single transfer request is asserted whenever any data is in the receive FIFO. A burst transfer request is asserted whenever the amount of data in the receive FIFO is 4 or more items. For the transmit channel, a single transfer request is asserted whenever at least one empty location is in the transmit FIFO. The burst request is asserted whenever the transmit FIFO has 4 or more empty slots. The 996 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller single and burst µDMA transfer requests are handled automatically by the μDMA controller depending how the µDMA channel is configured. To enable µDMA operation for the receive channel, the RXDMAE bit of the DMA Control (SSIDMACTL) register should be set. To enable µDMA operation for the transmit channel, the TXDMAE bit of SSIDMACTL should be set. If µDMA is enabled, then the μDMA controller triggers an interrupt when a transfer is complete. The interrupt occurs on the SSI interrupt vector. Therefore, if interrupts are used for SSI operation and µDMA is enabled, the SSI interrupt handler must be designed to handle the μDMA completion interrupt. See “Micro Direct Memory Access (μDMA)” on page 610 for more details about programming the μDMA controller. 15.4 Initialization and Configuration To enable and initialize the SSI, the following steps are necessary: 1. Enable the SSI module using the RCGCSSI register (see page 396). 2. Enable the clock to the appropriate GPIO module via the RCGCGPIO register (see page 389). To find out which GPIO port to enable, refer to Table 23-5 on page 1398. 3. Set the GPIO AFSEL bits for the appropriate pins (see page 698). To determine which GPIOs to configure, see Table 23-4 on page 1387. 4. Configure the PMCn fields in the GPIOPCTL register to assign the SSI signals to the appropriate pins. See page 717 and Table 23-5 on page 1398. For each of the frame formats, the SSI is configured using the following steps: 1. Ensure that the SSE bit in the SSICR1 register is clear before making any configuration changes. 2. Select whether the SSI is a master or slave: a. For master operations, set the SSICR1 register to 0x0000.0000. b. For slave mode (output enabled), set the SSICR1 register to 0x0000.0004. c. For slave mode (output disabled), set the SSICR1 register to 0x0000.000C. 3. Configure the clock prescale divisor by writing the SSICPSR register. 4. Write the SSICR0 register with the following configuration: ■ Serial clock rate (SCR) ■ Desired clock phase/polarity, if using Freescale SPI mode (SPH and SPO) ■ The protocol mode: Freescale SPI, TI SSF, MICROWIRE (FRF) ■ The data size (DSS) 5. Optionally, configure the μDMA channel (see “Micro Direct Memory Access (μDMA)” on page 610) and enable the DMA option(s) in the SSIDMACTL register. 6. Enable the SSI by setting the SSE bit in the SSICR1 register. As an example, assume the SSI must be configured to operate with the following parameters: November 08, 2011 997 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) ■ Master operation ■ Freescale SPI mode (SPO=1, SPH=1) ■ 1 Mbps bit rate ■ 8 data bits Assuming the system clock is 20 MHz, the bit rate calculation would be: SSIClk = SysClk / (CPSDVSR * (1 + SCR)) 1x106 = 20x106 / (CPSDVSR * (1 + SCR)) In this case, if CPSDVSR=0x2, SCR must be 0x9. The configuration sequence would be as follows: 1. Ensure that the SSE bit in the SSICR1 register is clear. 2. Write the SSICR1 register with a value of 0x0000.0000. 3. Write the SSICPSR register with a value of 0x0000.0002. 4. Write the SSICR0 register with a value of 0x0000.09C7. 5. The SSI is then enabled by setting the SSE bit in the SSICR1 register. 15.5 Register Map Table 15-2 on page 998 lists the SSI registers. The offset listed is a hexadecimal increment to the register’s address, relative to that SSI module’s base address: ■ ■ ■ ■ SSI0: 0x4000.8000 SSI1: 0x4000.9000 SSI2: 0x4000.A000 SSI3: 0x4000.B000 Note that the SSI module clock must be enabled before the registers can be programmed (see page 396). There must be a delay of 3 system clocks after the SSI module clock is enabled before any SSI module registers are accessed. Note: The SSI must be disabled (see the SSE bit in the SSICR1 register) before any of the control registers are reprogrammed. Table 15-2. SSI Register Map Offset Name Type Reset Description See page 0x000 SSICR0 R/W 0x0000.0000 SSI Control 0 1000 0x004 SSICR1 R/W 0x0000.0000 SSI Control 1 1002 0x008 SSIDR R/W 0x0000.0000 SSI Data 1004 0x00C SSISR RO 0x0000.0003 SSI Status 1005 0x010 SSICPSR R/W 0x0000.0000 SSI Clock Prescale 1007 998 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 15-2. SSI Register Map (continued) Description See page 0x0000.0000 SSI Interrupt Mask 1008 RO 0x0000.0008 SSI Raw Interrupt Status 1009 SSIMIS RO 0x0000.0000 SSI Masked Interrupt Status 1011 0x020 SSIICR W1C 0x0000.0000 SSI Interrupt Clear 1013 0x024 SSIDMACTL R/W 0x0000.0000 SSI DMA Control 1014 0xFC8 SSICC R/W 0x0000.0000 SSI Clock Configuration 1015 0xFD0 SSIPeriphID4 RO 0x0000.0000 SSI Peripheral Identification 4 1016 0xFD4 SSIPeriphID5 RO 0x0000.0000 SSI Peripheral Identification 5 1017 0xFD8 SSIPeriphID6 RO 0x0000.0000 SSI Peripheral Identification 6 1018 0xFDC SSIPeriphID7 RO 0x0000.0000 SSI Peripheral Identification 7 1019 0xFE0 SSIPeriphID0 RO 0x0000.0022 SSI Peripheral Identification 0 1020 0xFE4 SSIPeriphID1 RO 0x0000.0000 SSI Peripheral Identification 1 1021 0xFE8 SSIPeriphID2 RO 0x0000.0018 SSI Peripheral Identification 2 1022 0xFEC SSIPeriphID3 RO 0x0000.0001 SSI Peripheral Identification 3 1023 0xFF0 SSIPCellID0 RO 0x0000.000D SSI PrimeCell Identification 0 1024 0xFF4 SSIPCellID1 RO 0x0000.00F0 SSI PrimeCell Identification 1 1025 0xFF8 SSIPCellID2 RO 0x0000.0005 SSI PrimeCell Identification 2 1026 0xFFC SSIPCellID3 RO 0x0000.00B1 SSI PrimeCell Identification 3 1027 Offset Name Type Reset 0x014 SSIIM R/W 0x018 SSIRIS 0x01C 15.6 Register Descriptions The remainder of this section lists and describes the SSI registers, in numerical order by address offset. November 08, 2011 999 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 1: SSI Control 0 (SSICR0), offset 0x000 The SSICR0 register contains bit fields that control various functions within the SSI module. Functionality such as protocol mode, clock rate, and data size are configured in this register. SSI Control 0 (SSICR0) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 5 4 3 2 1 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 15 14 13 12 RO 0 RO 0 RO 0 RO 0 11 10 9 8 SCR Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15:8 SCR R/W 0x00 R/W 0 RO 0 7 6 SPH SPO R/W 0 R/W 0 FRF R/W 0 DSS R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Serial Clock Rate This bit field is used to generate the transmit and receive bit rate of the SSI. The bit rate is: BR=SysClk/(CPSDVSR * (1 + SCR)) where CPSDVSR is an even value from 2-254 programmed in the SSICPSR register, and SCR is a value from 0-255. 7 SPH R/W 0 SSI Serial Clock Phase This bit is only applicable to the Freescale SPI Format. The SPH control bit selects the clock edge that captures data and allows it to change state. This bit has the most impact on the first bit transmitted by either allowing or not allowing a clock transition before the first data capture edge. Value Description 6 SPO R/W 0 0 Data is captured on the first clock edge transition. 1 Data is captured on the second clock edge transition. SSI Serial Clock Polarity Value Description 0 A steady state Low value is placed on the SSIClk pin. 1 A steady state High value is placed on the SSIClk pin when data is not being transferred. 1000 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 5:4 FRF R/W 0x0 Description SSI Frame Format Select Value Frame Format 3:0 DSS R/W 0x0 0x0 Freescale SPI Frame Format 0x1 Texas Instruments Synchronous Serial Frame Format 0x2 MICROWIRE Frame Format 0x3 Reserved SSI Data Size Select Value Data Size 0x0-0x2 Reserved 0x3 4-bit data 0x4 5-bit data 0x5 6-bit data 0x6 7-bit data 0x7 8-bit data 0x8 9-bit data 0x9 10-bit data 0xA 11-bit data 0xB 12-bit data 0xC 13-bit data 0xD 14-bit data 0xE 15-bit data 0xF 16-bit data November 08, 2011 1001 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 2: SSI Control 1 (SSICR1), offset 0x004 The SSICR1 register contains bit fields that control various functions within the SSI module. Master and slave mode functionality is controlled by this register. SSI Control 1 (SSICR1) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x004 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:5 reserved RO 0x0000.0 4 EOT R/W 0 RO 0 RO 0 RO 0 RO 0 4 3 2 1 0 EOT SOD MS SSE LBM R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. End of Transmission Value Description 3 SOD R/W 0 0 The TXRIS interrupt indicates that the transmit FIFO is half full or less. 1 The End of Transmit interrupt mode for the TXRIS interrupt is enabled. SSI Slave Mode Output Disable This bit is relevant only in the Slave mode (MS=1). In multiple-slave systems, it is possible for the SSI master to broadcast a message to all slaves in the system while ensuring that only one slave drives data onto the serial output line. In such systems, the TXD lines from multiple slaves could be tied together. To operate in such a system, the SOD bit can be configured so that the SSI slave does not drive the SSITx pin. Value Description 2 MS R/W 0 0 SSI can drive the SSITx output in Slave mode. 1 SSI must not drive the SSITx output in Slave mode. SSI Master/Slave Select This bit selects Master or Slave mode and can be modified only when the SSI is disabled (SSE=0). Value Description 0 The SSI is configured as a master. 1 The SSI is configured as a slave. 1002 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 SSE R/W 0 Description SSI Synchronous Serial Port Enable Value Description 0 SSI operation is disabled. 1 SSI operation is enabled. Note: 0 LBM R/W 0 This bit must be cleared before any control registers are reprogrammed. SSI Loopback Mode Value Description 0 Normal serial port operation enabled. 1 Output of the transmit serial shift register is connected internally to the input of the receive serial shift register. November 08, 2011 1003 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 3: SSI Data (SSIDR), offset 0x008 Important: This register is read-sensitive. See the register description for details. The SSIDR register is 16-bits wide. When the SSIDR register is read, the entry in the receive FIFO that is pointed to by the current FIFO read pointer is accessed. When a data value is removed by the SSI receive logic from the incoming data frame, it is placed into the entry in the receive FIFO pointed to by the current FIFO write pointer. When the SSIDR register is written to, the entry in the transmit FIFO that is pointed to by the write pointer is written to. Data values are removed from the transmit FIFO one value at a time by the transmit logic. Each data value is loaded into the transmit serial shifter, then serially shifted out onto the SSITx pin at the programmed bit rate. When a data size of less than 16 bits is selected, the user must right-justify data written to the transmit FIFO. The transmit logic ignores the unused bits. Received data less than 16 bits is automatically right-justified in the receive buffer. When the SSI is programmed for MICROWIRE frame format, the default size for transmit data is eight bits (the most significant byte is ignored). The receive data size is controlled by the programmer. The transmit FIFO and the receive FIFO are not cleared even when the SSE bit in the SSICR1 register is cleared, allowing the software to fill the transmit FIFO before enabling the SSI. SSI Data (SSIDR) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 DATA Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 DATA R/W 0x0000 SSI Receive/Transmit Data A read operation reads the receive FIFO. A write operation writes the transmit FIFO. Software must right-justify data when the SSI is programmed for a data size that is less than 16 bits. Unused bits at the top are ignored by the transmit logic. The receive logic automatically right-justifies the data. 1004 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 4: SSI Status (SSISR), offset 0x00C The SSISR register contains bits that indicate the FIFO fill status and the SSI busy status. SSI Status (SSISR) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x00C Type RO, reset 0x0000.0003 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:5 reserved RO 0x0000.00 4 BSY RO 0 RO 0 RO 0 RO 0 RO 0 4 3 2 1 0 BSY RFF RNE TNF TFE RO 0 RO 0 RO 0 RO 1 RO 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Busy Bit Value Description 3 RFF RO 0 0 The SSI is idle. 1 The SSI is currently transmitting and/or receiving a frame, or the transmit FIFO is not empty. SSI Receive FIFO Full Value Description 2 RNE RO 0 0 The receive FIFO is not full. 1 The receive FIFO is full. SSI Receive FIFO Not Empty Value Description 1 TNF RO 1 0 The receive FIFO is empty. 1 The receive FIFO is not empty. SSI Transmit FIFO Not Full Value Description 0 The transmit FIFO is full. 1 The transmit FIFO is not full. November 08, 2011 1005 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Bit/Field Name Type Reset 0 TFE RO 1 Description SSI Transmit FIFO Empty Value Description 0 The transmit FIFO is not empty. 1 The transmit FIFO is empty. 1006 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 5: SSI Clock Prescale (SSICPSR), offset 0x010 The SSICPSR register specifies the division factor which is used to derive the SSIClk from the system clock. The clock is further divided by a value from 1 to 256, which is 1 + SCR. SCR is programmed in the SSICR0 register. The frequency of the SSIClk is defined by: SSIClk = SysClk / (CPSDVSR * (1 + SCR)) The value programmed into this register must be an even number between 2 and 254. The least-significant bit of the programmed number is hard-coded to zero. If an odd number is written to this register, data read back from this register has the least-significant bit as zero. SSI Clock Prescale (SSICPSR) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset CPSDVSR RO 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CPSDVSR R/W 0x00 SSI Clock Prescale Divisor This value must be an even number from 2 to 254, depending on the frequency of SSIClk. The LSB always returns 0 on reads. November 08, 2011 1007 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 6: SSI Interrupt Mask (SSIIM), offset 0x014 The SSIIM register is the interrupt mask set or clear register. It is a read/write register and all bits are cleared on reset. On a read, this register gives the current value of the mask on the corresponding interrupt. Setting a bit sets the mask, preventing the interrupt from being signaled to the interrupt controller. Clearing a bit clears the corresponding mask, enabling the interrupt to be sent to the interrupt controller. SSI Interrupt Mask (SSIIM) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x014 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 TXIM RXIM RTIM RORIM RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 TXIM R/W 0 SSI Transmit FIFO Interrupt Mask Value Description 2 RXIM R/W 0 0 The transmit FIFO interrupt is masked. 1 The transmit FIFO interrupt is not masked. SSI Receive FIFO Interrupt Mask Value Description 1 RTIM R/W 0 0 The receive FIFO interrupt is masked. 1 The receive FIFO interrupt is not masked. SSI Receive Time-Out Interrupt Mask Value Description 0 RORIM R/W 0 0 The receive FIFO time-out interrupt is masked. 1 The receive FIFO time-out interrupt is not masked. SSI Receive Overrun Interrupt Mask Value Description 0 The receive FIFO overrun interrupt is masked. 1 The receive FIFO overrun interrupt is not masked. 1008 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 7: SSI Raw Interrupt Status (SSIRIS), offset 0x018 The SSIRIS register is the raw interrupt status register. On a read, this register gives the current raw status value of the corresponding interrupt prior to masking. A write has no effect. SSI Raw Interrupt Status (SSIRIS) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x018 Type RO, reset 0x0000.0008 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 TXRIS RXRIS RTRIS RORRIS RO 1 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 TXRIS RO 1 SSI Transmit FIFO Raw Interrupt Status Value Description 0 No interrupt. 1 If the EOT bit in the SSICR1 register is clear, the transmit FIFO is half full or less. If the EOT bit is set, the transmit FIFO is empty, and the last bit has been transmitted out of the serializer. This bit is cleared when the transmit FIFO is more than half full (if the EOT bit is clear) or when it has any data in it (if the EOT bit is set). 2 RXRIS RO 0 SSI Receive FIFO Raw Interrupt Status Value Description 0 No interrupt. 1 The receive FIFO is half full or more. This bit is cleared when the receive FIFO is less than half full. 1 RTRIS RO 0 SSI Receive Time-Out Raw Interrupt Status Value Description 0 No interrupt. 1 The receive time-out has occurred. This bit is cleared when a 1 is written to the RTIC bit in the SSI Interrupt Clear (SSIICR) register. November 08, 2011 1009 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Bit/Field Name Type Reset 0 RORRIS RO 0 Description SSI Receive Overrun Raw Interrupt Status Value Description 0 No interrupt. 1 The receive FIFO has overflowed This bit is cleared when a 1 is written to the RORIC bit in the SSI Interrupt Clear (SSIICR) register. 1010 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 8: SSI Masked Interrupt Status (SSIMIS), offset 0x01C The SSIMIS register is the masked interrupt status register. On a read, this register gives the current masked status value of the corresponding interrupt. A write has no effect. SSI Masked Interrupt Status (SSIMIS) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x01C Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 TXMIS RXMIS RTMIS RORMIS RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 TXMIS RO 0 SSI Transmit FIFO Masked Interrupt Status Value Description 0 An interrupt has not occurred or is masked. 1 An unmasked interrupt was signaled due to the transmit FIFO being half full or less (if the EOT bit is clear) or due to the transmission of the last data bit (if the EOT bit is set). This bit is cleared when the transmit FIFO is more than half full (if the EOT bit is clear) or when it has any data in it (if the EOT bit is set). 2 RXMIS RO 0 SSI Receive FIFO Masked Interrupt Status Value Description 0 An interrupt has not occurred or is masked. 1 An unmasked interrupt was signaled due to the receive FIFO being half full or less. This bit is cleared when the receive FIFO is less than half full. 1 RTMIS RO 0 SSI Receive Time-Out Masked Interrupt Status Value Description 0 An interrupt has not occurred or is masked. 1 An unmasked interrupt was signaled due to the receive time out. This bit is cleared when a 1 is written to the RTIC bit in the SSI Interrupt Clear (SSIICR) register. November 08, 2011 1011 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Bit/Field Name Type Reset 0 RORMIS RO 0 Description SSI Receive Overrun Masked Interrupt Status Value Description 0 An interrupt has not occurred or is masked. 1 An unmasked interrupt was signaled due to the receive FIFO overflowing. This bit is cleared when a 1 is written to the RORIC bit in the SSI Interrupt Clear (SSIICR) register. 1012 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 9: SSI Interrupt Clear (SSIICR), offset 0x020 The SSIICR register is the interrupt clear register. On a write of 1, the corresponding interrupt is cleared. A write of 0 has no effect. SSI Interrupt Clear (SSIICR) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x020 Type W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 RTIC RORIC W1C 0 W1C 0 Bit/Field Name Type Reset Description 31:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 RTIC W1C 0 SSI Receive Time-Out Interrupt Clear Writing a 1 to this bit clears the RTRIS bit in the SSIRIS register and the RTMIS bit in the SSIMIS register. 0 RORIC W1C 0 SSI Receive Overrun Interrupt Clear Writing a 1 to this bit clears the RORRIS bit in the SSIRIS register and the RORMIS bit in the SSIMIS register. November 08, 2011 1013 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 10: SSI DMA Control (SSIDMACTL), offset 0x024 The SSIDMACTL register is the µDMA control register. SSI DMA Control (SSIDMACTL) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1 TXDMAE R/W 0 TXDMAE RXDMAE RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Transmit DMA Enable Value Description 0 RXDMAE R/W 0 0 µDMA for the transmit FIFO is disabled. 1 µDMA for the transmit FIFO is enabled. Receive DMA Enable Value Description 0 µDMA for the receive FIFO is disabled. 1 µDMA for the receive FIFO is enabled. 1014 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 11: SSI Clock Configuration (SSICC), offset 0xFC8 The SSICC register controls the baud clock source for the SSI module. Note: If the PIOSC is used for the SSI baud clock, the system clock frequency must be at least 16 MHz in Run mode. SSI Clock Configuration (SSICC) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFC8 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset CS Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3:0 CS R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Baud Clock Source The following table specifies the source that generates for the SSI baud clock: Value Description 0x0 Either the system clock (if the PLL bypass is in effect) or the PLL output (default). 0x1 PIOSC 0x2 - 0xF Reserved November 08, 2011 1015 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 12: SSI Peripheral Identification 4 (SSIPeriphID4), offset 0xFD0 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 4 (SSIPeriphID4) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFD0 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID4 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID4 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register [7:0] Can be used by software to identify the presence of this peripheral. 1016 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 13: SSI Peripheral Identification 5 (SSIPeriphID5), offset 0xFD4 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 5 (SSIPeriphID5) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFD4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID5 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID5 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register [15:8] Can be used by software to identify the presence of this peripheral. November 08, 2011 1017 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 14: SSI Peripheral Identification 6 (SSIPeriphID6), offset 0xFD8 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 6 (SSIPeriphID6) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFD8 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID6 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID6 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register [23:16] Can be used by software to identify the presence of this peripheral. 1018 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 15: SSI Peripheral Identification 7 (SSIPeriphID7), offset 0xFDC The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 7 (SSIPeriphID7) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFDC Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID7 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID7 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register [31:24] Can be used by software to identify the presence of this peripheral. November 08, 2011 1019 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 16: SSI Peripheral Identification 0 (SSIPeriphID0), offset 0xFE0 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 0 (SSIPeriphID0) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFE0 Type RO, reset 0x0000.0022 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 1 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID0 RO 0x22 RO 0 RO 0 RO 0 RO 1 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register [7:0] Can be used by software to identify the presence of this peripheral. 1020 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 17: SSI Peripheral Identification 1 (SSIPeriphID1), offset 0xFE4 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 1 (SSIPeriphID1) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFE4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID1 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID1 RO 0x00 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register [15:8] Can be used by software to identify the presence of this peripheral. November 08, 2011 1021 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 18: SSI Peripheral Identification 2 (SSIPeriphID2), offset 0xFE8 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 2 (SSIPeriphID2) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFE8 Type RO, reset 0x0000.0018 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 1 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID2 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID2 RO 0x18 RO 0 RO 0 RO 0 RO 0 RO 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register [23:16] Can be used by software to identify the presence of this peripheral. 1022 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 19: SSI Peripheral Identification 3 (SSIPeriphID3), offset 0xFEC The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 3 (SSIPeriphID3) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFEC Type RO, reset 0x0000.0001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID3 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 PID3 RO 0x01 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register [31:24] Can be used by software to identify the presence of this peripheral. November 08, 2011 1023 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 20: SSI PrimeCell Identification 0 (SSIPCellID0), offset 0xFF0 The SSIPCellIDn registers are hard-coded, and the fields within the register determine the reset value. SSI PrimeCell Identification 0 (SSIPCellID0) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFF0 Type RO, reset 0x0000.000D 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 1 RO 1 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CID0 RO 0x0D RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI PrimeCell ID Register [7:0] Provides software a standard cross-peripheral identification system. 1024 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 21: SSI PrimeCell Identification 1 (SSIPCellID1), offset 0xFF4 The SSIPCellIDn registers are hard-coded, and the fields within the register determine the reset value. SSI PrimeCell Identification 1 (SSIPCellID1) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFF4 Type RO, reset 0x0000.00F0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID1 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CID1 RO 0xF0 RO 0 RO 1 RO 1 RO 1 RO 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI PrimeCell ID Register [15:8] Provides software a standard cross-peripheral identification system. November 08, 2011 1025 Texas Instruments-Advance Information Synchronous Serial Interface (SSI) Register 22: SSI PrimeCell Identification 2 (SSIPCellID2), offset 0xFF8 The SSIPCellIDn registers are hard-coded, and the fields within the register determine the reset value. SSI PrimeCell Identification 2 (SSIPCellID2) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFF8 Type RO, reset 0x0000.0005 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 1 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID2 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CID2 RO 0x05 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI PrimeCell ID Register [23:16] Provides software a standard cross-peripheral identification system. 1026 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 23: SSI PrimeCell Identification 3 (SSIPCellID3), offset 0xFFC The SSIPCellIDn registers are hard-coded, and the fields within the register determine the reset value. SSI PrimeCell Identification 3 (SSIPCellID3) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 Offset 0xFFC Type RO, reset 0x0000.00B1 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID3 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CID3 RO 0xB1 RO 0 RO 1 RO 0 RO 1 RO 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI PrimeCell ID Register [31:24] Provides software a standard cross-peripheral identification system. November 08, 2011 1027 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface 16 Inter-Integrated Circuit (I2C) Interface The Inter-Integrated Circuit (I2C) bus provides bi-directional data transfer through a two-wire design (a serial data line SDA and a serial clock line SCL), and interfaces to external I2C devices such as serial memory (RAMs and ROMs), networking devices, LCDs, tone generators, and so on. The I2C bus may also be used for system testing and diagnostic purposes in product development and manufacture. The LM4F232H5BB microcontroller includes providing the ability to interact (both transmit and receive) with other I2C devices on the bus. ® The Stellaris LM4F232H5BB controller includes I2C modules with the following features: ■ Devices on the I2C bus can be designated as either a master or a slave – Supports both transmitting and receiving data as either a master or a slave – Supports simultaneous master and slave operation ■ Four I2C modes – Master transmit – Master receive – Slave transmit – Slave receive ■ Four transmission speeds: – Standard (100 Kbps) – Fast-mode (400 Kbps) – Fast-mode plus (1 Mbps) – High-speed mode (3.33 Mbps) ■ Clock low timeout interrupt ■ Dual slave address capability ■ Clock low timeout interrupt ■ Dual slave address capability ■ Master and slave interrupt generation – Master generates interrupts when a transmit or receive operation completes (or aborts due to an error) – Slave generates interrupts when data has been transferred or requested by a master or when a START or STOP condition is detected ■ Master with arbitration and clock synchronization, multimaster support, and 7-bit addressing mode 1028 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 16.1 Block Diagram Figure 16-1. I2C Block Diagram I2C Control Interrupt I2CSCL I2CMSA I2CSOAR I2CMCS I2CSCSR I2CMDR I2CSDR I2CMTPR I2CSIMR I2CMIMR I2CSRIS I2CMRIS I2CSMIS I2CMMIS I2CSICR I2CMICR I2CSSOAR2 I2CMCR I2CSACKCTL 2 I C Master Core I2CSDA I2CSCL I2C I/O Select I2CSDA I2CSCL 2 I C Slave Core I2CSDA I2CMCLKOCNT I2CMBMON I2CPP 16.2 Signal Description The following table lists the external signals of the I2C interface and describes the function of each. The I2C interface signals are alternate functions for some GPIO signals and default to be GPIO signals at reset., with the exception of the I2C0SCL and I2CSDA pins which default to the I2C function. The column in the table below titled "Pin Mux/Pin Assignment" lists the possible GPIO pin placements for the I2C signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 698) should be set to choose the I2C function. The number in parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control (GPIOPCTL) register (page 717) to assign the I2C signal to the specified GPIO port pin. Note that the I2CSCL pin should be set to open drain using the GPIO Open Drain Select (GPIOODR) register. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 674. Table 16-1. I2C Signals (157BGA) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description I2C0SCL E10 PB2 (3) I/O OD I2C module 0 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C0SDA D13 PB3 (3) I/O OD I2C module 0 data. I2C1SCL M4 K7 PA6 (3) PG4 (3) I/O OD I2C module 1 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C1SDA N2 L7 PA7 (3) PG5 (3) I/O OD I2C module 1 data. I2C2SCL A5 N8 PE4 (3) PF6 (3) I/O OD I2C module 2 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C2SDA B5 M8 PE5 (3) PF7 (3) I/O OD I2C module 2 data. November 08, 2011 1029 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Table 16-1. I2C Signals (157BGA) (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description I2C3SCL B2 L8 PD0 (3) PG0 (3) I/O OD I2C module 3 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C3SDA B1 K8 PD1 (3) PG1 (3) I/O OD I2C module 3 data. I2C4SCL N7 PG2 (3) I/O OD I2C module 4 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C4SDA M7 PG3 (3) I/O OD I2C module 4 data. I2C5SCL F4 N4 PB6 (3) PG6 (3) I/O OD I2C module 5 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C5SDA F3 N3 PB7 (3) PG7 (3) I/O OD I2C module 5 data. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 16.3 Functional Description Each I2C module is comprised of both master and slave functions. For proper operation, the SDA pin must be configured as an open-drain signal. A typical I2C bus configuration is shown in Figure 16-2. See “Inter-Integrated Circuit (I2C) Interface” on page 1427 for I2C timing diagrams. Figure 16-2. I2C Bus Configuration RPUP SCL SDA I2C Bus I2CSCL I2CSDA Stellaris® 16.3.1 RPUP SCL SDA 3rd Party Device with I2C Interface SCL SDA 3rd Party Device with I2C Interface I2C Bus Functional Overview The I2C bus uses only two signals: SDA and SCL, named I2CSDA and I2CSCL on Stellaris microcontrollers. SDA is the bi-directional serial data line and SCL is the bi-directional serial clock line. The bus is considered idle when both lines are High. Every transaction on the I2C bus is nine bits long, consisting of eight data bits and a single acknowledge bit. The number of bytes per transfer (defined as the time between a valid START and STOP condition, described in “START and STOP Conditions” on page 1031) is unrestricted, but each byte has to be followed by an acknowledge bit, and data must be transferred MSB first. When a receiver cannot receive another complete byte, it can hold the clock line SCL Low and force the transmitter into a wait state. The data transfer continues when the receiver releases the clock SCL. 1030 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 16.3.1.1 START and STOP Conditions The protocol of the I2C bus defines two states to begin and end a transaction: START and STOP. A High-to-Low transition on the SDA line while the SCL is High is defined as a START condition, and a Low-to-High transition on the SDA line while SCL is High is defined as a STOP condition. The bus is considered busy after a START condition and free after a STOP condition. See Figure 16-3. Figure 16-3. START and STOP Conditions SDA SDA SCL SCL START condition STOP condition The STOP bit determines if the cycle stops at the end of the data cycle or continues on to a repeated START condition. To generate a single transmit cycle, the I2C Master Slave Address (I2CMSA) register is written with the desired address, the R/S bit is cleared, and the Control register is written with ACK=X (0 or 1), STOP=1, START=1, and RUN=1 to perform the operation and stop. When the operation is completed (or aborted due an error), the interrupt pin becomes active and the data may be read from the I2C Master Data (I2CMDR) register. When the I2C module operates in Master receiver mode, the ACK bit is normally set causing the I2C bus controller to transmit an acknowledge automatically after each byte. This bit must be cleared when the I2C bus controller requires no further data to be transmitted from the slave transmitter. When operating in slave mode, two bits in the I2C Slave Raw Interrupt Status (I2CSRIS) register indicate detection of start and stop conditions on the bus; while two bits in the I2C Slave Masked Interrupt Status (I2CSMIS) register allow start and stop conditions to be promoted to controller interrupts (when interrupts are enabled). 16.3.1.2 Data Format with 7-Bit Address Data transfers follow the format shown in Figure 16-4. After the START condition, a slave address is transmitted. This address is 7-bits long followed by an eighth bit, which is a data direction bit (R/S bit in the I2CMSA register). If the R/S bit is clear, it indicates a transmit operation (send), and if it is set, it indicates a request for data (receive). A data transfer is always terminated by a STOP condition generated by the master, however, a master can initiate communications with another device on the bus by generating a repeated START condition and addressing another slave without first generating a STOP condition. Various combinations of receive/transmit formats are then possible within a single transfer. Figure 16-4. Complete Data Transfer with a 7-Bit Address SDA MSB SCL 1 Start 2 LSB R/S ACK 7 8 9 MSB 1 2 Slave address 7 Data LSB ACK 8 9 Stop The first seven bits of the first byte make up the slave address (see Figure 16-5). The eighth bit determines the direction of the message. A zero in the R/S position of the first byte means that the November 08, 2011 1031 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface master transmits (sends) data to the selected slave, and a one in this position means that the master receives data from the slave. Figure 16-5. R/S Bit in First Byte MSB LSB R/S Slave address 16.3.1.3 Data Validity The data on the SDA line must be stable during the high period of the clock, and the data line can only change when SCL is Low (see Figure 16-6). Figure 16-6. Data Validity During Bit Transfer on the I2C Bus SDA SCL Data line Change stable of data allowed 16.3.1.4 Acknowledge All bus transactions have a required acknowledge clock cycle that is generated by the master. During the acknowledge cycle, the transmitter (which can be the master or slave) releases the SDA line. To acknowledge the transaction, the receiver must pull down SDA during the acknowledge clock cycle. The data transmitted out by the receiver during the acknowledge cycle must comply with the data validity requirements described in “Data Validity” on page 1032. When a slave receiver does not acknowledge the slave address, SDA must be left High by the slave so that the master can generate a STOP condition and abort the current transfer. If the master device is acting as a receiver during a transfer, it is responsible for acknowledging each transfer made by the slave. Because the master controls the number of bytes in the transfer, it signals the end of data to the slave transmitter by not generating an acknowledge on the last data byte. The slave transmitter must then release SDA to allow the master to generate the STOP or a repeated START condition. If the slave is required to provide a manual ACK or NACK, the I2C Slave ACK Control (I2CSACKCTL) register allows the slave to NACK for invalid data or command or ACK for valid data or command. When this operation is enabled, the I2C clock is pulled low after the last data bit until this register is written with the indicated response. 16.3.1.5 Clock Low Timeout The I2C slave can extend the transaction by pulling the clock low periodically to create a slow bit transfer rate. The I2C module has a 12-bit programmable counter that is used to track how long the clock has been held low. The upper 8 bits of the count value are software programmable through the I2C Master Clock Low Timeout Count (I2CMCLKOCNT) register. The master can program this register with a count value that is acceptable to wait for the transaction to delay. The count is loaded at the START condition and counts down on every system clock edge. When the terminal 1032 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller count is reached, the I2C master can force a STOP condition on the bus the next time the slave releases the clock and abort the transaction. The CLKRIS bit in the I2C Master Raw Interrupt Status (I2CMRIS) register is set when the clock timeout period is reached, allowing the master to start corrective action to resolve the remote slave state. In addition, the CLKTO bit in the I2C Master Control/Status (I2CMCS) register is set; this bit is cleared when a STOP condition is sent or during the I2C master reset.. The status of the raw SDA and SCL signals are readable by software through the SDA and SCL bits in the I2C Master Bus Monitor (I2CMBMON) register to help determine the state of the remote slave. If the slave holds the clock low continuously, the only solution is to interrupt the processor using the CLKRIS bit and resolve the condition at higher protocol levels by resetting both the master and the remote slave. 16.3.1.6 Dual Address The I2C interface supports dual address capability for the slave. The additional programmable address is provided and can be matched if enabled. In legacy mode with dual address disabled, the I2C slave provides an ACK on the bus if the address matches the OAR field in the I2CSOAR register. In dual address mode, the I2C slave provides an ACK on the bus if either the OAR field in the I2CSOAR register or the OAR2 field in the I2CSOAR2 register is matched. The enable for dual address is programmable through the OAR2EN bit in the I2CSOAR2 register. The legacy address has always higher priority and to avoid confusion, and there is no disable on the legacy address. The OAR2SEL bit in the I2CSCSR register indicates if the address that was ACKed is the alternate address or not. When this bit is clear, it indicates either legacy operation or no address match. 16.3.1.7 Arbitration A master may start a transfer only if the bus is idle. It's possible for two or more masters to generate a START condition within minimum hold time of the START condition. In these situations, an arbitration scheme takes place on the SDA line, while SCL is High. During arbitration, the first of the competing master devices to place a '1' (High) on SDA while another master transmits a '0' (Low) switches off its data output stage and retires until the bus is idle again. Arbitration can take place over several bits. Its first stage is a comparison of address bits, and if both masters are trying to address the same device, arbitration continues on to the comparison of data bits. 16.3.2 Available Speed Modes The I2C bus can run in Standard mode (100 kbps), Fast mode (400 kbps), Fast mode plus (1 Mbps) or High-Speed mode (3.33 Mbps). The selected mode should match the speed of the other I2C devices on the bus. 16.3.2.1 Standard and Fast Modes Standard and Fast modes are selected using a value in the I2C Master Timer Period (I2CMTPR) register that results in an SCL frequency of 100 kbps for Standard mode, 400 kbps for Fast mode, or 1 Mbps for Fast mode plus. The I2C clock rate is determined by the parameters CLK_PRD, TIMER_PRD, SCL_LP, and SCL_HP where: CLK_PRD is the system clock period SCL_LP is the low phase of SCL (fixed at 6) November 08, 2011 1033 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface SCL_HP is the high phase of SCL (fixed at 4) TIMER_PRD is the programmed value in the I2CMTPR register (see page 1053). The I2C clock period is calculated as follows: SCL_PERIOD = 2 × (1 + TIMER_PRD) × (SCL_LP + SCL_HP) × CLK_PRD For example: CLK_PRD = 50 ns TIMER_PRD = 2 SCL_LP=6 SCL_HP=4 yields a SCL frequency of: 1/SCL_PERIOD = 333 Khz Table 16-2 gives examples of the timer periods that should be used to generate Standard, Fast mode, and Fast mode plus SCL frequencies based on various system clock frequencies. Table 16-2. Examples of I2C Master Timer Period versus Speed Mode 16.3.2.2 System Clock Timer Period Standard Mode Timer Period Fast Mode Timer Period Fast Mode Plus 4 MHz 0x01 100 Kbps - - - - 6 MHz 0x02 100 Kbps - - - - 12.5 MHz 0x06 89 Kbps 0x01 312 Kbps - - 16.7 MHz 0x08 93 Kbps 0x02 278 Kbps - - 20 MHz 0x09 100 Kbps 0x02 333 Kbps - - 25 MHz 0x0C 96.2 Kbps 0x03 312 Kbps - - 33 MHz 0x10 97.1 Kbps 0x04 330 Kbps - - 40 MHz 0x13 100 Kbps 0x04 400 Kbps 0x01 1000 Kbps 50 MHz 0x18 100 Kbps 0x06 357 Kbps 0x02 833 Kbps 80 MHz 0x27 100 Kbps 0x09 400 Kbps 0x03 1000 Kbps High-Speed Mode High-Speed mode is configured by setting the HS bit in the I2C Master Control/Status (I2CMCS) register. High-Speed mode transmits data at a high bit rate with a 66.6%/33.3% duty cycle, but communication and arbitration are done at Standard, Fast mode, or Fast-mode plus speed, depending on which is selected by the user. When the HS bit in the I2CMCS register is set, current mode pull-ups are enabled. The clock period can be selected using the equation above, but in this case, SCL_LP=2 and SCL_HP=1. So for example: CLK_PRD = 25 ns TIMER_PRD = 1 SCL_LP=2 SCL_HP=1 yields a SCL frequency of: 1034 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 1/T = 3.33 Mhz Table 16-3 on page 1035 gives examples of timer period and system clock in High-Speed mode. Table 16-3. Examples of I2C Master Timer Period in High-Speed Mode 16.3.3 System Clock Timer Period Transmission Mode 40 MHz 0x01 3.33 Mbps 50 MHz 0x02 2.77 Mbps 80 MHz 0x03 3.33 Mbps Interrupts The I2C can generate interrupts when the following conditions are observed: ■ Master transaction completed ■ Master arbitration lost ■ Master transaction error ■ Master bus timeout ■ Slave transaction received ■ Slave transaction requested ■ Stop condition on bus detected ■ Start condition on bus detected The I2C master and I2C slave modules have separate interrupt signals. While both modules can generate interrupts for multiple conditions, only a single interrupt signal is sent to the interrupt controller. 16.3.3.1 I2C Master Interrupts The I2C master module generates an interrupt when a transaction completes (either transmit or receive), when arbitration is lost, or when an error occurs during a transaction. To enable the I2C master interrupt, software must set the IM bit in the I2C Master Interrupt Mask (I2CMIMR) register. When an interrupt condition is met, software must check the ERROR and ARBLST bits in the I2C Master Control/Status (I2CMCS) register to verify that an error didn't occur during the last transaction and to ensure that arbitration has not been lost. An error condition is asserted if the last transaction wasn't acknowledged by the slave. If an error is not detected and the master has not lost arbitration, the application can proceed with the transfer. The interrupt is cleared by writing a 1 to the IC bit in the I2C Master Interrupt Clear (I2CMICR) register. If the application doesn't require the use of interrupts, the raw interrupt status is always visible via the I2C Master Raw Interrupt Status (I2CMRIS) register. 16.3.3.2 I2C Slave Interrupts The slave module can generate an interrupt when data has been received or requested. This interrupt is enabled by setting the DATAIM bit in the I2C Slave Interrupt Mask (I2CSIMR) register. Software determines whether the module should write (transmit) or read (receive) data from the I2C Slave November 08, 2011 1035 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Data (I2CSDR) register, by checking the RREQ and TREQ bits of the I2C Slave Control/Status (I2CSCSR) register. If the slave module is in receive mode and the first byte of a transfer is received, the FBR bit is set along with the RREQ bit. The interrupt is cleared by setting the DATAIC bit in the I2C Slave Interrupt Clear (I2CSICR) register. In addition, the slave module can generate an interrupt when a start and stop condition is detected. These interrupts are enabled by setting the STARTIM and STOPIM bits of the I2C Slave Interrupt Mask (I2CSIMR) register and cleared by writing a 1 to the STOPIC and STARTIC bits of the I2C Slave Interrupt Clear (I2CSICR) register. If the application doesn't require the use of interrupts, the raw interrupt status is always visible via the I2C Slave Raw Interrupt Status (I2CSRIS) register. 16.3.4 Loopback Operation The I2C modules can be placed into an internal loopback mode for diagnostic or debug work by setting the LPBK bit in the I2C Master Configuration (I2CMCR) register. In loopback mode, the SDA and SCL signals from the master and slave modules are tied together. 16.3.5 Command Sequence Flow Charts This section details the steps required to perform the various I2C transfer types in both master and slave mode. 16.3.5.1 I2C Master Command Sequences The figures that follow show the command sequences available for the I2C master. 1036 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 16-7. Master Single TRANSMIT Idle Write Slave Address to I2CMSA Sequence may be omitted in a Single Master system Write data to I2CMDR Read I2CMCS NO BUSBSY bit=0? YES Write ---0-111 to I2CMCS Read I2CMCS NO BUSY bit=0? YES Error Service NO ERROR bit=0? YES Idle November 08, 2011 1037 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Figure 16-8. Master Single RECEIVE Idle Write Slave Address to I2CMSA Sequence may be omitted in a Single Master system Read I2CMCS NO BUSBSY bit=0? YES Write ---00111 to I2CMCS Read I2CMCS NO BUSY bit=0? YES Error Service NO ERROR bit=0? YES Read data from I2CMDR Idle 1038 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 16-9. Master TRANSMIT with Repeated START Idle Write Slave Address to I2CMSA Sequence may be omitted in a Single Master system Read I2CMCS Write data to I2CMDR BUSY bit=0? YES Read I2CMCS ERROR bit=0? NO NO NO BUSBSY bit=0? YES Write data to I2CMDR YES Write ---0-011 to I2CMCS NO ARBLST bit=1? YES Write ---0-001 to I2CMCS NO Index=n? YES Write ---0-101 to I2CMCS Write ---0-100 to I2CMCS Error Service Idle Read I2CMCS NO BUSY bit=0? YES Error Service NO ERROR bit=0? YES Idle November 08, 2011 1039 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Figure 16-10. Master RECEIVE with Repeated START Idle Write Slave Address to I2CMSA Sequence may be omitted in a Single Master system Read I2CMCS BUSY bit=0? Read I2CMCS NO YES NO BUSBSY bit=0? ERROR bit=0? NO YES Write ---01011 to I2CMCS NO Read data from I2CMDR ARBLST bit=1? YES Write ---01001 to I2CMCS NO Write ---0-100 to I2CMCS Index=m-1? Error Service YES Write ---00101 to I2CMCS Idle Read I2CMCS BUSY bit=0? NO YES NO ERROR bit=0? YES Error Service Read data from I2CMDR Idle 1040 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 16-11. Master RECEIVE with Repeated START after TRANSMIT with Repeated START Idle Master operates in Master Transmit mode STOP condition is not generated Write Slave Address to I2CMSA Write ---01011 to I2CMCS Master operates in Master Receive mode Repeated START condition is generated with changing data direction Idle November 08, 2011 1041 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Figure 16-12. Master TRANSMIT with Repeated START after RECEIVE with Repeated START Idle Master operates in Master Receive mode STOP condition is not generated Write Slave Address to I2CMSA Write ---0-011 to I2CMCS Master operates in Master Transmit mode Repeated START condition is generated with changing data direction Idle 16.3.5.2 I2C Slave Command Sequences Figure 16-13 on page 1043 presents the command sequence available for the I2C slave. 1042 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 16-13. Slave Command Sequence Idle Write OWN Slave Address to I2CSOAR Write -------1 to I2CSCSR Read I2CSCSR NO TREQ bit=1? YES Write data to I2CSDR 16.4 NO RREQ bit=1? FBR is also valid YES Read data from I2CSDR Initialization and Configuration The following example shows how to configure the I2C module to transmit a single byte as a master. This assumes the system clock is 20 MHz. 1. Enable the I2C clock using the RCGCI2C register in the System Control module (see page 398). 2. Enable the clock to the appropriate GPIO module via the RCGCGPIO register in the System Control module (see page 389). To find out which GPIO port to enable, refer to Table 23-5 on page 1398. 3. In the GPIO module, enable the appropriate pins for their alternate function using the GPIOAFSEL register (see page 698). To determine which GPIOs to configure, see Table 23-4 on page 1387. 4. Enable the I2C pins for Open Drain operation. See page 704. 5. Configure the PMCn fields in the GPIOPCTL register to assign the I2C signals to the appropriate pins. See page 717 and Table 23-5 on page 1398. 6. Initialize the I2C Master by writing the I2CMCR register with a value of 0x0000.0010. November 08, 2011 1043 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface 7. Set the desired SCL clock speed of 100 Kbps by writing the I2CMTPR register with the correct value. The value written to the I2CMTPR register represents the number of system clock periods in one SCL clock period. The TPR value is determined by the following equation: TPR = (System Clock/(2*(SCL_LP + SCL_HP)*SCL_CLK))-1; TPR = (20MHz/(2*(6+4)*100000))-1; TPR = 9 Write the I2CMTPR register with the value of 0x0000.0009. 8. Specify the slave address of the master and that the next operation is a Transmit by writing the I2CMSA register with a value of 0x0000.0076. This sets the slave address to 0x3B. 9. Place data (byte) to be transmitted in the data register by writing the I2CMDR register with the desired data. 10. Initiate a single byte transmit of the data from Master to Slave by writing the I2CMCS register with a value of 0x0000.0007 (STOP, START, RUN). 11. Wait until the transmission completes by polling the I2CMCS register’s BUSBSY bit until it has been cleared. 12. Check the ERROR bit in the I2CMCS register to confirm the transmit was acknowledged. 16.5 Register Map Table 16-4 on page 1044 lists the I2C registers. All addresses given are relative to the I2C base address: ■ ■ ■ ■ ■ ■ I2C 0: 0x4002.0000 I2C 1: 0x4002.1000 I2C 2: 0x4002.2000 I2C 3: 0x4002.3000 I2C 4: 0x400C.0000 I2C 5: 0x400C.1000 Note that the I2C module clock must be enabled before the registers can be programmed (see page 398). There must be a delay of 3 system clocks after the I2C module clock is enabled before any I2C module registers are accessed. ® The hw_i2c.h file in the StellarisWare Driver Library uses a base address of 0x800 for the I2C slave registers. Be aware when using registers with offsets between 0x800 and 0x818 that StellarisWare uses an offset between 0x000 and 0x018 with the slave base address. Table 16-4. Inter-Integrated Circuit (I2C) Interface Register Map Offset Description See page 0x0000.0000 I2C Master Slave Address 1046 R/W 0x0000.0020 I2C Master Control/Status 1047 R/W 0x0000.0000 I2C Master Data 1052 Name Type Reset 0x000 I2CMSA R/W 0x004 I2CMCS 0x008 I2CMDR I2C Master 1044 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 16-4. Inter-Integrated Circuit (I2C) Interface Register Map (continued) Description See page 0x0000.0001 I2C Master Timer Period 1053 R/W 0x0000.0000 I2C Master Interrupt Mask 1054 I2CMRIS RO 0x0000.0000 I2C Master Raw Interrupt Status 1055 0x018 I2CMMIS RO 0x0000.0000 I2C Master Masked Interrupt Status 1056 0x01C I2CMICR WO 0x0000.0000 I2C Master Interrupt Clear 1057 0x020 I2CMCR R/W 0x0000.0000 I2C Master Configuration 1058 0x024 I2CMCLKOCNT R/W 0x0000.0000 I2C Master Clock Low Timeout Count 1059 0x02C I2CMBMON RO 0x0000.0000 I2C Master Bus Monitor 1060 0x800 I2CSOAR R/W 0x0000.0000 I2C Slave Own Address 1061 0x804 I2CSCSR RO 0x0000.0000 I2C Slave Control/Status 1062 0x808 I2CSDR R/W 0x0000.0000 I2C Slave Data 1064 0x80C I2CSIMR R/W 0x0000.0000 I2C Slave Interrupt Mask 1065 0x810 I2CSRIS RO 0x0000.0000 I2C Slave Raw Interrupt Status 1066 0x814 I2CSMIS RO 0x0000.0000 I2C Slave Masked Interrupt Status 1067 0x818 I2CSICR WO 0x0000.0000 I2C Slave Interrupt Clear 1068 0x81C I2CSOAR2 R/W 0x0000.0000 I2C Slave Own Address 2 1069 0x820 I2CSACKCTL R/W 0x0000.0000 I2C Slave ACK Control 1070 Offset Name Type Reset 0x00C I2CMTPR R/W 0x010 I2CMIMR 0x014 I2C Slave I2C Status and Control 0xFC0 I2CPP RO 0x0000.0001 I2C Peripheral Properties 1071 0xFC4 I2CPC RO 0x0000.0000 I2C Peripheral Configuration 1072 16.6 Register Descriptions (I2C Master) The remainder of this section lists and describes the I2C master registers, in numerical order by address offset. November 08, 2011 1045 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 1: I2C Master Slave Address (I2CMSA), offset 0x000 This register consists of eight bits: seven address bits (A6-A0), and a Receive/Send bit, which determines if the next operation is a Receive (High), or Transmit (Low). I2C Master Slave Address (I2CMSA) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 SA RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:1 SA R/W 0x00 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 0 R/S R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C Slave Address This field specifies bits A6 through A0 of the slave address. 0 R/S R/W 0 Receive/Send The R/S bit specifies if the next operation is a Receive (High) or Transmit (Low). Value Description 0 Transmit 1 Receive 1046 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 2: I2C Master Control/Status (I2CMCS), offset 0x004 This register accesses status bits when read and control bits when written. When read, the status register indicates the state of the I2C bus controller. When written, the control register configures the I2C controller operation. The START bit generates the START or REPEATED START condition. The STOP bit determines if the cycle stops at the end of the data cycle or continues on to a repeated START condition. To generate a single transmit cycle, the I2C Master Slave Address (I2CMSA) register is written with the desired address, the R/S bit is cleared, and this register is written with ACK=X (0 or 1), STOP=1, START=1, and RUN=1 to perform the operation and stop. When the operation is completed (or aborted due an error), an interrupt becomes active and the data may be read from the I2CMDR register. When the I2C module operates in Master receiver mode, the ACK bit is normally set, causing the I2C bus controller to transmit an acknowledge automatically after each byte. This bit must be cleared when the I2C bus controller requires no further data to be transmitted from the slave transmitter. Read-Only Status Register I2C Master Control/Status (I2CMCS) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x004 Type RO, reset 0x0000.0020 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 CLKTO BUSBSY IDLE ARBLST ERROR BUSY RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 CLKTO RO 0 DATACK ADRACK RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Clock Timeout Error Value Description 0 No clock timeout error. 1 The clock timeout error has occurred. This bit is cleared when the master sends a STOP condition or if the I2C master is reset. November 08, 2011 1047 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Bit/Field Name Type Reset 6 BUSBSY RO 0 Description Bus Busy Value Description 0 The I2C bus is idle. 1 The I2C bus is busy. The bit changes based on the START and STOP conditions. 5 IDLE RO 1 I2C Idle Value Description 4 ARBLST RO 0 0 The I2C controller is not idle. 1 The I2C controller is idle. Arbitration Lost Value Description 3 DATACK RO 0 0 The I2C controller won arbitration. 1 The I2C controller lost arbitration. Acknowledge Data Value Description 2 ADRACK RO 0 0 The transmitted data was acknowledged 1 The transmitted data was not acknowledged. Acknowledge Address Value Description 1 ERROR RO 0 0 The transmitted address was acknowledged 1 The transmitted address was not acknowledged. Error Value Description 0 No error was detected on the last operation. 1 An error occurred on the last operation. The error can be from the slave address not being acknowledged or the transmit data not being acknowledged. 0 BUSY RO 0 I2C Busy Value Description 0 The controller is idle. 1 The controller is busy. When the BUSY bit is set, the other status bits are not valid. 1048 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Write-Only Control Register I2C Master Control/Status (I2CMCS) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x004 Type WO, reset 0x0000.0020 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 4 3 2 1 0 HS ACK STOP START RUN WO 0 WO 0 WO 0 WO 0 WO 0 Bit/Field Name Type Reset Description 31:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 HS WO 0 High-Speed Enable Value Description 3 ACK WO 0 0 The master operates in Standard, Fast mode, or Fast mode plus as selected by using a value in the I2CMTPR register that results in an SCL frequency of 100 kbps for Standard mode, 400 kbps for Fast mode, or 1 Mpbs for Fast mode plus. 1 The master operates in High-Speed mode with transmission speeds up to 3.33 Mbps. Data Acknowledge Enable Value Description 2 STOP WO 0 0 The received data byte is not acknowledged automatically by the master. 1 The received data byte is acknowledged automatically by the master. See field decoding in Table 16-5 on page 1050. Generate STOP Value Description 0 The controller does not generate the STOP condition. 1 The controller generates the STOP condition. See field decoding in Table 16-5 on page 1050. November 08, 2011 1049 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Bit/Field Name Type Reset 1 START WO 0 Description Generate START Value Description 0 RUN WO 0 The controller does not generate the START condition. 1 The controller generates the START or repeated START condition. See field decoding in Table 16-5 on page 1050. I2C Master Enable 0 Value Description 0 The master is disabled. 1 The master is enabled to transmit or receive data. See field decoding in Table 16-5 on page 1050. Table 16-5. Write Field Decoding for I2CMCS[3:0] Field Current I2CMSA[0] State R/S Idle I2CMCS[3:0] ACK STOP START RUN 0 X a 0 1 1 START condition followed by TRANSMIT (master goes to the Master Transmit state). 0 X 1 1 1 START condition followed by a TRANSMIT and STOP condition (master remains in Idle state). 1 0 0 1 1 START condition followed by RECEIVE operation with negative ACK (master goes to the Master Receive state). 1 0 1 1 1 START condition followed by RECEIVE and STOP condition (master remains in Idle state). 1 1 0 1 1 START condition followed by RECEIVE (master goes to the Master Receive state). 1 1 1 1 1 Illegal All other combinations not listed are non-operations. Master Transmit Description NOP X X 0 0 1 TRANSMIT operation (master remains in Master Transmit state). X X 1 0 0 STOP condition (master goes to Idle state). X X 1 0 1 TRANSMIT followed by STOP condition (master goes to Idle state). 0 X 0 1 1 Repeated START condition followed by a TRANSMIT (master remains in Master Transmit state). 0 X 1 1 1 Repeated START condition followed by TRANSMIT and STOP condition (master goes to Idle state). 1 0 0 1 1 Repeated START condition followed by a RECEIVE operation with a negative ACK (master goes to Master Receive state). 1 0 1 1 1 Repeated START condition followed by a TRANSMIT and STOP condition (master goes to Idle state). 1 1 0 1 1 Repeated START condition followed by RECEIVE (master goes to Master Receive state). 1 1 1 1 1 Illegal. All other combinations not listed are non-operations. NOP. 1050 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 16-5. Write Field Decoding for I2CMCS[3:0] Field (continued) Current I2CMSA[0] State R/S I2CMCS[3:0] Description ACK STOP START RUN X 0 0 0 1 RECEIVE operation with negative ACK (master remains in Master Receive state). X X 1 0 0 STOP condition (master goes to Idle state). X 0 1 0 1 RECEIVE followed by STOP condition (master goes to Idle state). X 1 0 0 1 RECEIVE operation (master remains in Master Receive state). X 1 1 0 1 Illegal. 1 0 0 1 1 Repeated START condition followed by RECEIVE operation with a negative ACK (master remains in Master Receive state). 1 0 1 1 1 Repeated START condition followed by RECEIVE and STOP condition (master goes to Idle state). 1 1 0 1 1 Repeated START condition followed by RECEIVE (master remains in Master Receive state). 0 X 0 1 1 Repeated START condition followed by TRANSMIT (master goes to Master Transmit state). 0 X 1 1 1 Repeated START condition followed by TRANSMIT and STOP condition (master goes to Idle state). Master Receive All other combinations not listed are non-operations. b NOP. a. An X in a table cell indicates the bit can be 0 or 1. b. In Master Receive mode, a STOP condition should be generated only after a Data Negative Acknowledge executed by the master or an Address Negative Acknowledge executed by the slave. November 08, 2011 1051 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 3: I2C Master Data (I2CMDR), offset 0x008 Important: This register is read-sensitive. See the register description for details. This register contains the data to be transmitted when in the Master Transmit state and the data received when in the Master Receive state. I2C Master Data (I2CMDR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset DATA RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 DATA R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Data Transferred Data transferred during transaction. 1052 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 4: I2C Master Timer Period (I2CMTPR), offset 0x00C This register specifies the period of the SCL clock. I2C Master Timer Period (I2CMTPR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x00C Type R/W, reset 0x0000.0001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 HS RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 HS R/W 0x0 RO 0 R/W 0 TPR R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. High-Speed Enable Value Description 6:0 TPR R/W 0x1 1 The SCL Clock Period set by TPR applies to High-speed mode (3.33 Mbps). 0 The SCL Clock Period set by TPR applies to Standard mode (100 Kbps), Fast-mode (400 Kbps), or Fast-mode plus (1 Mbps). SCL Clock Period This field specifies the period of the SCL clock. SCL_PRD = 2×(1 + TPR)×(SCL_LP + SCL_HP)×CLK_PRD where: SCL_PRD is the SCL line period (I2C clock). TPR is the Timer Period register value (range of 1 to 127). SCL_LP is the SCL Low period (fixed at 6). SCL_HP is the SCL High period (fixed at 4). CLK_PRD is the system clock period in ns. November 08, 2011 1053 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 5: I2C Master Interrupt Mask (I2CMIMR), offset 0x010 This register controls whether a raw interrupt is promoted to a controller interrupt. I2C Master Interrupt Mask (I2CMIMR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 CLKIM IM R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 CLKIM R/W 0 Clock Timeout Interrupt Mask Value Description 0 IM R/W 0 1 The clock timeout interrupt is sent to the interrupt controller when the CLKRIS bit in the I2CMRIS register is set. 0 The CLKRIS interrupt is suppressed and not sent to the interrupt controller. Interrupt Mask Value Description 1 The master interrupt is sent to the interrupt controller when the RIS bit in the I2CMRIS register is set. 0 The RIS interrupt is suppressed and not sent to the interrupt controller. 1054 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 6: I2C Master Raw Interrupt Status (I2CMRIS), offset 0x014 This register specifies whether an interrupt is pending. I2C Master Raw Interrupt Status (I2CMRIS) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x014 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 CLKRIS RIS RO 0 RO 0 Bit/Field Name Type Reset Description 31:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 CLKRIS RO 0 Clock Timeout Raw Interrupt Status Value Description 1 The clock timeout interrupt is pending. 0 No interrupt. This bit is cleared by writing a 1 to the CLKIC bit in the I2CMICR register. 0 RIS RO 0 Raw Interrupt Status Value Description 1 A master interrupt is pending. 0 No interrupt. This bit is cleared by writing a 1 to the IC bit in the I2CMICR register. November 08, 2011 1055 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 7: I2C Master Masked Interrupt Status (I2CMMIS), offset 0x018 This register specifies whether an interrupt was signaled. I2C Master Masked Interrupt Status (I2CMMIS) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x018 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 CLKMIS MIS RO 0 RO 0 Bit/Field Name Type Reset Description 31:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 CLKMIS RO 0 Clock Timeout Masked Interrupt Status Value Description 1 An unmasked clock timeout interrupt was signaled and is pending. 0 No interrupt. This bit is cleared by writing a 1 to the CLKIC bit in the I2CMICR register. 0 MIS RO 0 Masked Interrupt Status Value Description 1 An unmasked master interrupt was signaled and is pending. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the IC bit in the I2CMICR register. 1056 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 8: I2C Master Interrupt Clear (I2CMICR), offset 0x01C This register clears the raw and masked interrupts. I2C Master Interrupt Clear (I2CMICR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x01C Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 CLKIC IC WO 0 WO 0 Bit/Field Name Type Reset Description 31:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 CLKIC WO 0 Clock Timeout Interrupt Clear Writing a 1 to this bit clears the CLKRIS bit in the I2CMRIS register and the CLKMIS bit in the I2CMMIS register. A read of this register returns no meaningful data. 0 IC WO 0 Interrupt Clear Writing a 1 to this bit clears the RIS bit in the I2CMRIS register and the MIS bit in the I2CMMIS register. A read of this register returns no meaningful data. November 08, 2011 1057 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 9: I2C Master Configuration (I2CMCR), offset 0x020 This register configures the mode (Master or Slave) and sets the interface for test mode loopback. I2C Master Configuration (I2CMCR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x020 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:6 reserved RO 0x0000.00 5 SFE R/W 0 RO 0 RO 0 RO 0 5 4 SFE MFE R/W 0 R/W 0 reserved RO 0 RO 0 0 LPBK RO 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C Slave Function Enable Value Description 4 MFE R/W 0 1 Slave mode is enabled. 0 Slave mode is disabled. I2C Master Function Enable Value Description 3:1 reserved RO 0x0 0 LPBK R/W 0 1 Master mode is enabled. 0 Master mode is disabled. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C Loopback Value Description 1 The controller in a test mode loopback configuration. 0 Normal operation. 1058 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 10: I2C Master Clock Low Timeout Count (I2CMCLKOCNT), offset 0x024 This register contains the upper 8 bits of a 12-bit counter that can be used to keep the timeout limit for clock stretching by a remote slave. The lower four bits of the counter are not user visible. I2C Master Clock Low Timeout Count (I2CMCLKOCNT) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset CNTL RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 CNTL R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C Master Count This field contains the upper 8 bits of a 12-bit counter for the clock low timeout count. November 08, 2011 1059 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 11: I2C Master Bus Monitor (I2CMBMON), offset 0x02C This register is used to determine the SCL and SDA signal status. I2C Master Bus Monitor (I2CMBMON) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x02C Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1 SDA RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 SDA SCL RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C SDA Status Value Description 0 SCL RO 0 1 The I2CSDA signal is high. 0 The I2CSDA signal is low. I2C SCL Status Value Description 16.7 1 The I2CSCL signal is high. 0 The I2CSCL signal is low. Register Descriptions (I2C Slave) The remainder of this section lists and describes the I2C slave registers, in numerical order by address offset. 1060 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 12: I2C Slave Own Address (I2CSOAR), offset 0x800 This register consists of seven address bits that identify the Stellaris I2C device on the I2C bus. I2C Slave Own Address (I2CSOAR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x800 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 OAR Bit/Field Name Type Reset 31:7 reserved RO 0x0000.00 6:0 OAR R/W 0x00 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C Slave Own Address This field specifies bits A6 through A0 of the slave address. November 08, 2011 1061 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 13: I2C Slave Control/Status (I2CSCSR), offset 0x804 This register functions as a control register when written, and a status register when read. Read-Only Status Register I2C Slave Control/Status (I2CSCSR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x804 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 OAR2SEL FBR TREQ RREQ RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 OAR2SEL RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. OAR2 Address Matched Value Description 1 OAR2 address matched and ACKed by the slave. 0 Either the address is not matched or the match is in legacy mode. This bit gets reevaluated after every address comparison. 2 FBR RO 0 First Byte Received Value Description 1 The first byte following the slave’s own address has been received. 0 The first byte has not been received. This bit is only valid when the RREQ bit is set and is automatically cleared when data has been read from the I2CSDR register. Note: This bit is not used for slave transmit operations. 1062 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 TREQ RO 0 Description Transmit Request Value Description 0 RREQ RO 0 1 The I2C controller has been addressed as a slave transmitter and is using clock stretching to delay the master until data has been written to the I2CSDR register. 0 No outstanding transmit request. Receive Request Value Description 1 The I2C controller has outstanding receive data from the I2C master and is using clock stretching to delay the master until the data has been read from the I2CSDR register. 0 No outstanding receive data. Write-Only Control Register I2C Slave Control/Status (I2CSCSR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x804 Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 DA WO 0 RO 0 0 DA RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 WO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Device Active Value Description 0 Disables the I2C slave operation. 1 Enables the I2C slave operation. Once this bit has been set, it should not be set again unless it has been cleared by writing a 0 or by a reset, otherwise transfer failures may occur. November 08, 2011 1063 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 14: I2C Slave Data (I2CSDR), offset 0x808 Important: This register is read-sensitive. See the register description for details. This register contains the data to be transmitted when in the Slave Transmit state, and the data received when in the Slave Receive state. I2C Slave Data (I2CSDR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x808 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset DATA RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:0 DATA R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Data for Transfer This field contains the data for transfer during a slave receive or transmit operation. 1064 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 15: I2C Slave Interrupt Mask (I2CSIMR), offset 0x80C This register controls whether a raw interrupt is promoted to a controller interrupt. I2C Slave Interrupt Mask (I2CSIMR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x80C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 STOPIM STARTIM DATAIM RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 STOPIM R/W 0 Stop Condition Interrupt Mask Value Description 1 STARTIM R/W 0 1 The STOP condition interrupt is sent to the interrupt controller when the STOPRIS bit in the I2CSRIS register is set. 0 The STOPRIS interrupt is suppressed and not sent to the interrupt controller. Start Condition Interrupt Mask Value Description 0 DATAIM R/W 0 1 The START condition interrupt is sent to the interrupt controller when the STARTRIS bit in the I2CSRIS register is set. 0 The STARTRIS interrupt is suppressed and not sent to the interrupt controller. Data Interrupt Mask Value Description 1 The data received or data requested interrupt is sent to the interrupt controller when the DATARIS bit in the I2CSRIS register is set. 0 The DATARIS interrupt is suppressed and not sent to the interrupt controller. November 08, 2011 1065 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 16: I2C Slave Raw Interrupt Status (I2CSRIS), offset 0x810 This register specifies whether an interrupt is pending. I2C Slave Raw Interrupt Status (I2CSRIS) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x810 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 STOPRIS STARTRIS DATARIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 STOPRIS RO 0 Stop Condition Raw Interrupt Status Value Description 1 A STOP condition interrupt is pending. 0 No interrupt. This bit is cleared by writing a 1 to the STOPIC bit in the I2CSICR register. 1 STARTRIS RO 0 Start Condition Raw Interrupt Status Value Description 1 A START condition interrupt is pending. 0 No interrupt. This bit is cleared by writing a 1 to the STARTIC bit in the I2CSICR register. 0 DATARIS RO 0 Data Raw Interrupt Status Value Description 1 A data received or data requested interrupt is pending. 0 No interrupt. This bit is cleared by writing a 1 to the DATAIC bit in the I2CSICR register. 1066 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 17: I2C Slave Masked Interrupt Status (I2CSMIS), offset 0x814 This register specifies whether an interrupt was signaled. I2C Slave Masked Interrupt Status (I2CSMIS) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x814 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 STOPMIS STARTMIS DATAMIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 STOPMIS RO 0 Stop Condition Masked Interrupt Status Value Description 1 An unmasked STOP condition interrupt was signaled is pending. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the STOPIC bit in the I2CSICR register. 1 STARTMIS RO 0 Start Condition Masked Interrupt Status Value Description 1 An unmasked START condition interrupt was signaled is pending. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the STARTIC bit in the I2CSICR register. 0 DATAMIS RO 0 Data Masked Interrupt Status Value Description 1 An unmasked data received or data requested interrupt was signaled is pending. 0 An interrupt has not occurred or is masked. This bit is cleared by writing a 1 to the DATAIC bit in the I2CSICR register. November 08, 2011 1067 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 18: I2C Slave Interrupt Clear (I2CSICR), offset 0x818 This register clears the raw interrupt. A read of this register returns no meaningful data. I2C Slave Interrupt Clear (I2CSICR) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x818 Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 STOPIC STARTIC RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 WO 0 WO 0 0 DATAIC WO 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 STOPIC WO 0 Stop Condition Interrupt Clear Writing a 1 to this bit clears the STOPRIS bit in the I2CSRIS register and the STOPMIS bit in the I2CSMIS register. A read of this register returns no meaningful data. 1 STARTIC WO 0 Start Condition Interrupt Clear Writing a 1 to this bit clears the STOPRIS bit in the I2CSRIS register and the STOPMIS bit in the I2CSMIS register. A read of this register returns no meaningful data. 0 DATAIC WO 0 Data Interrupt Clear Writing a 1 to this bit clears the STOPRIS bit in the I2CSRIS register and the STOPMIS bit in the I2CSMIS register. A read of this register returns no meaningful data. 1068 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 19: I2C Slave Own Address 2 (I2CSOAR2), offset 0x81C This register consists of seven address bits that identify the alternate address for the I2C device on the I2C bus. I2C Slave Own Address 2 (I2CSOAR2) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x81C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset OAR2EN RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 OAR2EN R/W 0 R/W 0 OAR2 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C Slave Own Address 2 Enable Value Description 6:0 OAR2 R/W 0x00 1 Enables the use of the alternate address in the OAR2 field. 0 The alternate address is disabled. I2C Slave Own Address 2 This field specifies the alternate OAR2 address. November 08, 2011 1069 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 20: I2C Slave ACK Control (I2CSACKCTL), offset 0x820 This register enables the I2C slave to NACK for invalid data or command or ACK for valid data or command. The I2C clock is pulled low after the last data bit until this register is written. I2C Slave ACK Control (I2CSACKCTL) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0x820 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1 ACKOVAL R/W 0 ACKOVAL ACKOEN R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C Slave ACK Override Value Value Description 0 ACKOEN R/W 0 1 A NACK is sent indicating invalid data or command. 0 An ACK is sent indicating valid data or command. I2C Slave ACK Override Enable Value Description 16.8 1 An ACK or NACK is sent according to the value written to the ACKOVAL bit. 0 A response in not provided. Register Descriptions (I2C Status and Control) The remainder of this section lists and describes the I2C status and control registers, in numerical order by address offset. 1070 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 21: I2C Peripheral Properties (I2CPP), offset 0xFC0 The I2CPP register provides information regarding the properties of the I2C module. I2C Peripheral Properties (I2CPP) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0xFC0 Type RO, reset 0x0000.0001 31 30 29 28 27 26 25 24 0 0 0 0 0 0 0 0 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 23 22 21 20 19 18 17 16 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 RO 1 reserved Type Reset reserved Type Reset 0 HS Bit/Field Name Type Reset Description 31:1 reserved - 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 HS RO 0x1 High-Speed Capable Value Description 1 The interface is capable of High-Speed operation. 0 The interface is capable of Standard, Fast, or Fast mode plus operation. November 08, 2011 1071 Texas Instruments-Advance Information Inter-Integrated Circuit (I2C) Interface Register 22: I2C Peripheral Configuration (I2CPC), offset 0xFC4 The I2CPC register provides information regarding the configuration of the I2C module. I2C Peripheral Configuration (I2CPC) I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 Offset 0xFC4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset reserved Type Reset RO 0 HS Bit/Field Name Type Reset Description 31:1 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 HS RO 1 High-Speed Capable Value Description 1 The interface is set to High-Speed operation. Note that this encoding may only be used if the I2CPP HS bit is set. Otherwise, this encoding is not available. 0 The interface is set to Standard, Fast or Fast mode plus operation. 1072 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 17 Controller Area Network (CAN) Module Controller Area Network (CAN) is a multicast, shared serial bus standard for connecting electronic control units (ECUs). CAN was specifically designed to be robust in electromagnetically-noisy environments and can utilize a differential balanced line like RS-485 or a more robust twisted-pair wire. Originally created for automotive purposes, it is also used in many embedded control applications (such as industrial and medical). Bit rates up to 1 Mbps are possible at network lengths less than 40 meters. Decreased bit rates allow longer network distances (for example, 125 Kbps at 500 meters). ® The Stellaris LM4F232H5BB microcontroller includes two CAN units with the following features: ■ CAN protocol version 2.0 part A/B ■ Bit rates up to 1 Mbps ■ 32 message objects with individual identifier masks ■ Maskable interrupt ■ Disable Automatic Retransmission mode for Time-Triggered CAN (TTCAN) applications ■ Programmable Loopback mode for self-test operation ■ Programmable FIFO mode enables storage of multiple message objects ■ Gluelessly attaches to an external CAN transceiver through the CANnTX and CANnRX signals November 08, 2011 1073 Texas Instruments-Advance Information Controller Area Network (CAN) Module 17.1 Block Diagram Figure 17-1. CAN Controller Block Diagram CAN Control CANCTL CANSTS CANERR CANBIT CANINT CANTST CANBRPE CAN Tx CAN Interface 1 APB Pins APB Interface CANIF1CRQ CANIF1CMSK CANIF1MSK1 CANIF1MSK2 CANIF1ARB1 CANIF1ARB2 CANIF1MCTL CANIF1DA1 CANIF1DA2 CANIF1DB1 CANIF1DB2 CAN Core CAN Rx CAN Interface 2 CANIF2CRQ CANIF2CMSK CANIF2MSK1 CANIF2MSK2 CANIF2ARB1 CANIF2ARB2 CANIF2MCTL CANIF2DA1 CANIF2DA2 CANIF2DB1 CANIF2DB2 Message Object Registers CANTXRQ1 CANTXRQ2 CANNWDA1 CANNWDA2 CANMSG1INT CANMSG2INT CANMSG1VAL CANMSG2VAL Message RAM 32 Message Objects 17.2 Signal Description The following table lists the external signals of the CAN controller and describes the function of each. The CAN controller signals are alternate functions for some GPIO signals and default to be GPIO signals at reset. The column in the table below titled "Pin Mux/Pin Assignment" lists the possible GPIO pin placements for the CAN signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 698) should be set to choose the CAN controller function. The number in parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control (GPIOPCTL) register (page 717) to assign the CAN signal to the specified GPIO port pin. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 674. 1074 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 17-1. Controller Area Network Signals (157BGA) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description CAN0Rx B6 A5 M9 A8 PB4 (8) PE4 (8) PF0 (3) PN0 (1) I TTL CAN module 0 receive. CAN0Tx A6 B5 K10 B8 PB5 (8) PE5 (8) PF3 (3) PN1 (1) O TTL CAN module 0 transmit. CAN1Rx L3 A7 PA0 (8) PE6 (8) I TTL CAN module 1 receive. CAN1Tx M1 B7 PA1 (8) PE7 (8) O TTL CAN module 1 transmit. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 17.3 Functional Description The Stellaris CAN controller conforms to the CAN protocol version 2.0 (parts A and B). Message transfers that include data, remote, error, and overload frames with an 11-bit identifier (standard) or a 29-bit identifier (extended) are supported. Transfer rates can be programmed up to 1 Mbps. The CAN module consists of three major parts: ■ CAN protocol controller and message handler ■ Message memory ■ CAN register interface A data frame contains data for transmission, whereas a remote frame contains no data and is used to request the transmission of a specific message object. The CAN data/remote frame is constructed as shown in Figure 17-2. November 08, 2011 1075 Texas Instruments-Advance Information Controller Area Network (CAN) Module Figure 17-2. CAN Data/Remote Frame Remote Transmission Request Start Of Frame Bus Idle R S Control O Message Delimiter T Field R F Number 1 Of Bits 11 or 29 1 6 Delimiter Bits Data Field CRC Sequence A C K EOP IFS 0 . . . 64 15 1 1 1 7 3 CRC Sequence End of Frame Field CRC Field Arbitration Field Bit Stuffing Bus Idle Interframe Field Acknowledgement Field CAN Data Frame The protocol controller transfers and receives the serial data from the CAN bus and passes the data on to the message handler. The message handler then loads this information into the appropriate message object based on the current filtering and identifiers in the message object memory. The message handler is also responsible for generating interrupts based on events on the CAN bus. The message object memory is a set of 32 identical memory blocks that hold the current configuration, status, and actual data for each message object. These memory blocks are accessed via either of the CAN message object register interfaces. The message memory is not directly accessible in the Stellaris memory map, so the Stellaris CAN controller provides an interface to communicate with the message memory via two CAN interface register sets for communicating with the message objects. The message object memory cannot be directly accessed, so these two interfaces must be used to read or write to each message object. The two message object interfaces allow parallel access to the CAN controller message objects when multiple objects may have new information that must be processed. In general, one interface is used for transmit data and one for receive data. 17.3.1 Initialization To use the CAN controller, the peripheral clock must be enabled using the RCGC0 register (see page 293). In addition, the clock to the appropriate GPIO module must be enabled via the RCGC2 register (see page 300). To find out which GPIO port to enable, refer to Table 23-4 on page 1387. Set the GPIO AFSEL bits for the appropriate pins (see page 698). Configure the PMCn fields in the GPIOPCTL register to assign the CAN signals to the appropriate pins. See page 717 and Table 23-5 on page 1398. Software initialization is started by setting the INIT bit in the CAN Control (CANCTL) register (with software or by a hardware reset) or by going bus-off, which occurs when the transmitter's error counter exceeds a count of 255. While INIT is set, all message transfers to and from the CAN bus are stopped and the CANnTX signal is held High. Entering the initialization state does not change the configuration of the CAN controller, the message objects, or the error counters. However, some configuration registers are only accessible while in the initialization state. 1076 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller To initialize the CAN controller, set the CAN Bit Timing (CANBIT) register and configure each message object. If a message object is not needed, label it as not valid by clearing the MSGVAL bit in the CAN IFn Arbitration 2 (CANIFnARB2) register. Otherwise, the whole message object must be initialized, as the fields of the message object may not have valid information, causing unexpected results. Both the INIT and CCE bits in the CANCTL register must be set in order to access the CANBIT register and the CAN Baud Rate Prescaler Extension (CANBRPE) register to configure the bit timing. To leave the initialization state, the INIT bit must be cleared. Afterwards, the internal Bit Stream Processor (BSP) synchronizes itself to the data transfer on the CAN bus by waiting for the occurrence of a sequence of 11 consecutive recessive bits (indicating a bus idle condition) before it takes part in bus activities and starts message transfers. Message object initialization does not require the CAN to be in the initialization state and can be done on the fly. However, message objects should all be configured to particular identifiers or set to not valid before message transfer starts. To change the configuration of a message object during normal operation, clear the MSGVAL bit in the CANIFnARB2 register to indicate that the message object is not valid during the change. When the configuration is completed, set the MSGVAL bit again to indicate that the message object is once again valid. 17.3.2 Operation Two sets of CAN Interface Registers (CANIF1x and CANIF2x) are used to access the message objects in the Message RAM. The CAN controller coordinates transfers to and from the Message RAM to and from the registers. The two sets are independent and identical and can be used to queue transactions. Generally, one interface is used to transmit data and one is used to receive data. Once the CAN module is initialized and the INIT bit in the CANCTL register is cleared, the CAN module synchronizes itself to the CAN bus and starts the message transfer. As each message is received, it goes through the message handler's filtering process, and if it passes through the filter, is stored in the message object specified by the MNUM bit in the CAN IFn Command Request (CANIFnCRQ) register. The whole message (including all arbitration bits, data-length code, and eight data bytes) is stored in the message object. If the Identifier Mask (the MSK bits in the CAN IFn Mask 1 and CAN IFn Mask 2 (CANIFnMSKn) registers) is used, the arbitration bits that are masked to "don't care" may be overwritten in the message object. The CPU may read or write each message at any time via the CAN Interface Registers. The message handler guarantees data consistency in case of concurrent accesses. The transmission of message objects is under the control of the software that is managing the CAN hardware. Message objects can be used for one-time data transfers or can be permanent message objects used to respond in a more periodic manner. Permanent message objects have all arbitration and control set up, and only the data bytes are updated. At the start of transmission, the appropriate TXRQST bit in the CAN Transmission Request n (CANTXRQn) register and the NEWDAT bit in the CAN New Data n (CANNWDAn) register are set. If several transmit messages are assigned to the same message object (when the number of message objects is not sufficient), the whole message object has to be configured before the transmission of this message is requested. The transmission of any number of message objects may be requested at the same time; they are transmitted according to their internal priority, which is based on the message identifier (MNUM) for the message object, with 1 being the highest priority and 32 being the lowest priority. Messages may be updated or set to not valid any time, even when their requested transmission is still pending. The old data is discarded when a message is updated before its pending transmission has started. Depending on the configuration of the message object, the transmission of a message may be requested autonomously by the reception of a remote frame with a matching identifier. November 08, 2011 1077 Texas Instruments-Advance Information Controller Area Network (CAN) Module Transmission can be automatically started by the reception of a matching remote frame. To enable this mode, set the RMTEN bit in the CAN IFn Message Control (CANIFnMCTL) register. A matching received remote frame causes the TXRQST bit to be set, and the message object automatically transfers its data or generates an interrupt indicating a remote frame was requested. A remote frame can be strictly a single message identifier, or it can be a range of values specified in the message object. The CAN mask registers, CANIFnMSKn, configure which groups of frames are identified as remote frame requests. The UMASK bit in the CANIFnMCTL register enables the MSK bits in the CANIFnMSKn register to filter which frames are identified as a remote frame request. The MXTD bit in the CANIFnMSK2 register should be set if a remote frame request is expected to be triggered by 29-bit extended identifiers. 17.3.3 Transmitting Message Objects If the internal transmit shift register of the CAN module is ready for loading, and if a data transfer is not occurring between the CAN Interface Registers and message RAM, the valid message object with the highest priority that has a pending transmission request is loaded into the transmit shift register by the message handler and the transmission is started. The message object's NEWDAT bit in the CANNWDAn register is cleared. After a successful transmission, and if no new data was written to the message object since the start of the transmission, the TXRQST bit in the CANTXRQn register is cleared. If the CAN controller is configured to interrupt on a successful transmission of a message object, (the TXIE bit in the CAN IFn Message Control (CANIFnMCTL) register is set), the INTPND bit in the CANIFnMCTL register is set after a successful transmission. If the CAN module has lost the arbitration or if an error occurred during the transmission, the message is re-transmitted as soon as the CAN bus is free again. If, meanwhile, the transmission of a message with higher priority has been requested, the messages are transmitted in the order of their priority. 17.3.4 Configuring a Transmit Message Object The following steps illustrate how to configure a transmit message object. 1. In the CAN IFn Command Mask (CANIFnCMASK) register: ■ Set the WRNRD bit to specify a write to the CANIFnCMASK register; specify whether to transfer the IDMASK, DIR, and MXTD of the message object into the CAN IFn registers using the MASK bit ■ Specify whether to transfer the ID, DIR, XTD, and MSGVAL of the message object into the interface registers using the ARB bit ■ Specify whether to transfer the control bits into the interface registers using the CONTROL bit ■ Specify whether to clear the INTPND bit in the CANIFnMCTL register using the CLRINTPND bit ■ Specify whether to clear the NEWDAT bit in the CANNWDAn register using the NEWDAT bit ■ Specify which bits to transfer using the DATAA and DATAB bits 2. In the CANIFnMSK1 register, use the MSK[15:0] bits to specify which of the bits in the 29-bit or 11-bit message identifier are used for acceptance filtering. Note that MSK[15:0] in this register are used for bits [15:0] of the 29-bit message identifier and are not used for an 11-bit identifier. A value of 0x00 enables all messages to pass through the acceptance filtering. Also 1078 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller note that in order for these bits to be used for acceptance filtering, they must be enabled by setting the UMASK bit in the CANIFnMCTL register. 3. In the CANIFnMSK2 register, use the MSK[12:0] bits to specify which of the bits in the 29-bit or 11-bit message identifier are used for acceptance filtering. Note that MSK[12:0] are used for bits [28:16] of the 29-bit message identifier; whereas MSK[12:2] are used for bits [10:0] of the 11-bit message identifier. Use the MXTD and MDIR bits to specify whether to use XTD and DIR for acceptance filtering. A value of 0x00 enables all messages to pass through the acceptance filtering. Also note that in order for these bits to be used for acceptance filtering, they must be enabled by setting the UMASK bit in the CANIFnMCTL register. 4. For a 29-bit identifier, configure ID[15:0] in the CANIFnARB1 register for bits [15:0] of the message identifier and ID[12:0] in the CANIFnARB2 register for bits [28:16] of the message identifier. Set the XTD bit to indicate an extended identifier; set the DIR bit to indicate transmit; and set the MSGVAL bit to indicate that the message object is valid. 5. For an 11-bit identifier, disregard the CANIFnARB1 register and configure ID[12:2] in the CANIFnARB2 register for bits [10:0] of the message identifier. Clear the XTD bit to indicate a standard identifier; set the DIR bit to indicate transmit; and set the MSGVAL bit to indicate that the message object is valid. 6. In the CANIFnMCTL register: ■ Optionally set the UMASK bit to enable the mask (MSK, MXTD, and MDIR specified in the CANIFnMSK1 and CANIFnMSK2 registers) for acceptance filtering ■ Optionally set the TXIE bit to enable the INTPND bit to be set after a successful transmission ■ Optionally set the RMTEN bit to enable the TXRQST bit to be set on the reception of a matching remote frame allowing automatic transmission ■ Set the EOB bit for a single message object ■ Configure the DLC[3:0] field to specify the size of the data frame. Take care during this configuration not to set the NEWDAT, MSGLST, INTPND or TXRQST bits. 7. Load the data to be transmitted into the CAN IFn Data (CANIFnDA1, CANIFnDA2, CANIFnDB1, CANIFnDB2) registers. Byte 0 of the CAN data frame is stored in DATA[7:0] in the CANIFnDA1 register. 8. Program the number of the message object to be transmitted in the MNUM field in the CAN IFn Command Request (CANIFnCRQ) register. 9. When everything is properly configured, set the TXRQST bit in the CANIFnMCTL register. Once this bit is set, the message object is available to be transmitted, depending on priority and bus availability. Note that setting the RMTEN bit in the CANIFnMCTL register can also start message transmission if a matching remote frame has been received. 17.3.5 Updating a Transmit Message Object The CPU may update the data bytes of a Transmit Message Object any time via the CAN Interface Registers and neither the MSGVAL bit in the CANIFnARB2 register nor the TXRQST bits in the CANIFnMCTL register have to be cleared before the update. November 08, 2011 1079 Texas Instruments-Advance Information Controller Area Network (CAN) Module Even if only some of the data bytes are to be updated, all four bytes of the corresponding CANIFnDAn/CANIFnDBn register have to be valid before the content of that register is transferred to the message object. Either the CPU must write all four bytes into the CANIFnDAn/CANIFnDBn register or the message object is transferred to the CANIFnDAn/CANIFnDBn register before the CPU writes the new data bytes. In order to only update the data in a message object, the WRNRD, DATAA and DATAB bits in the CANIFnMSKn register are set, followed by writing the updated data into CANIFnDA1, CANIFnDA2, CANIFnDB1, and CANIFnDB2 registers, and then the number of the message object is written to the MNUM field in the CAN IFn Command Request (CANIFnCRQ) register. To begin transmission of the new data as soon as possible, set the TXRQST bit in the CANIFnMSKn register. To prevent the clearing of the TXRQST bit in the CANIFnMCTL register at the end of a transmission that may already be in progress while the data is updated, the NEWDAT and TXRQST bits have to be set at the same time in the CANIFnMCTL register. When these bits are set at the same time, NEWDAT is cleared as soon as the new transmission has started. 17.3.6 Accepting Received Message Objects When the arbitration and control field (the ID and XTD bits in the CANIFnARB2 and the RMTEN and DLC[3:0] bits of the CANIFnMCTL register) of an incoming message is completely shifted into the CAN controller, the message handling capability of the controller starts scanning the message RAM for a matching valid message object. To scan the message RAM for a matching message object, the controller uses the acceptance filtering programmed through the mask bits in the CANIFnMSKn register and enabled using the UMASK bit in the CANIFnMCTL register. Each valid message object, starting with object 1, is compared with the incoming message to locate a matching message object in the message RAM. If a match occurs, the scanning is stopped and the message handler proceeds depending on whether it is a data frame or remote frame that was received. 17.3.7 Receiving a Data Frame The message handler stores the message from the CAN controller receive shift register into the matching message object in the message RAM. The data bytes, all arbitration bits, and the DLC bits are all stored into the corresponding message object. In this manner, the data bytes are connected with the identifier even if arbitration masks are used. The NEWDAT bit of the CANIFnMCTL register is set to indicate that new data has been received. The CPU should clear this bit when it reads the message object to indicate to the controller that the message has been received, and the buffer is free to receive more messages. If the CAN controller receives a message and the NEWDAT bit is already set, the MSGLST bit in the CANIFnMCTL register is set to indicate that the previous data was lost. If the system requires an interrupt on successful reception of a frame, the RXIE bit of the CANIFnMCTL register should be set. In this case, the INTPND bit of the same register is set, causing the CANINT register to point to the message object that just received a message. The TXRQST bit of this message object should be cleared to prevent the transmission of a remote frame. 17.3.8 Receiving a Remote Frame A remote frame contains no data, but instead specifies which object should be transmitted. When a remote frame is received, three different configurations of the matching message object have to be considered: 1080 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 17-2. Message Object Configurations Configuration in CANIFnMCTL ■ ■ DIR = 1 (direction = transmit); programmed in the At the reception of a matching remote frame, the TXRQST bit of this CANIFnARB2 register message object is set. The rest of the message object remains unchanged, and the controller automatically transfers the data in RMTEN = 1 (set the TXRQST bit of the the message object as soon as possible. CANIFnMCTL register at reception of the frame to enable transmission) ■ UMASK = 1 or 0 ■ DIR = 1 (direction = transmit); programmed in the At the reception of a matching remote frame, the TXRQST bit of this CANIFnARB2 register message object remains unchanged, and the remote frame is ignored. This remote frame is disabled, the data is not transferred RMTEN = 0 (do not change the TXRQST bit of the and nothing indicates that the remote frame ever happened. CANIFnMCTL register at reception of the frame) ■ ■ UMASK = 0 (ignore mask in the CANIFnMSKn register) ■ DIR = 1 (direction = transmit); programmed in the At the reception of a matching remote frame, the TXRQST bit of this message object is cleared. The arbitration and control field (ID + CANIFnARB2 register XTD + RMTEN + DLC) from the shift register is stored into the message RMTEN = 0 (do not change the TXRQST bit of the object in the message RAM, and the NEWDAT bit of this message CANIFnMCTL register at reception of the frame) object is set. The data field of the message object remains unchanged; the remote frame is treated similar to a received data UMASK = 1 (use mask (MSK, MXTD, and MDIR in frame. This mode is useful for a remote data request from another the CANIFnMSKn register) for acceptance filtering) CAN device for which the Stellaris controller does not have readily available data. The software must fill the data and answer the frame manually. ■ ■ 17.3.9 Description Receive/Transmit Priority The receive/transmit priority for the message objects is controlled by the message number. Message object 1 has the highest priority, while message object 32 has the lowest priority. If more than one transmission request is pending, the message objects are transmitted in order based on the message object with the lowest message number. This prioritization is separate from that of the message identifier which is enforced by the CAN bus. As a result, if message object 1 and message object 2 both have valid messages to be transmitted, message object 1 is always transmitted first regardless of the message identifier in the message object itself. 17.3.10 Configuring a Receive Message Object The following steps illustrate how to configure a receive message object. 1. Program the CAN IFn Command Mask (CANIFnCMASK) register as described in the “Configuring a Transmit Message Object” on page 1078 section, except that the WRNRD bit is set to specify a write to the message RAM. 2. Program the CANIFnMSK1and CANIFnMSK2 registers as described in the “Configuring a Transmit Message Object” on page 1078 section to configure which bits are used for acceptance filtering. Note that in order for these bits to be used for acceptance filtering, they must be enabled by setting the UMASK bit in the CANIFnMCTL register. 3. In the CANIFnMSK2 register, use the MSK[12:0] bits to specify which of the bits in the 29-bit or 11-bit message identifier are used for acceptance filtering. Note that MSK[12:0] are used for bits [28:16] of the 29-bit message identifier; whereas MSK[12:2] are used for bits [10:0] of the 11-bit message identifier. Use the MXTD and MDIR bits to specify whether to use XTD and November 08, 2011 1081 Texas Instruments-Advance Information Controller Area Network (CAN) Module DIR for acceptance filtering. A value of 0x00 enables all messages to pass through the acceptance filtering. Also note that in order for these bits to be used for acceptance filtering, they must be enabled by setting the UMASK bit in the CANIFnMCTL register. 4. Program the CANIFnARB1 and CANIFnARB2 registers as described in the “Configuring a Transmit Message Object” on page 1078 section to program XTD and ID bits for the message identifier to be received; set the MSGVAL bit to indicate a valid message; and clear the DIR bit to specify receive. 5. In the CANIFnMCTL register: ■ Optionally set the UMASK bit to enable the mask (MSK, MXTD, and MDIR specified in the CANIFnMSK1 and CANIFnMSK2 registers) for acceptance filtering ■ Optionally set the RXIE bit to enable the INTPND bit to be set after a successful reception ■ Clear the RMTEN bit to leave the TXRQST bit unchanged ■ Set the EOB bit for a single message object ■ Configure the DLC[3:0] field to specify the size of the data frame Take care during this configuration not to set the NEWDAT, MSGLST, INTPND or TXRQST bits. 6. Program the number of the message object to be received in the MNUM field in the CAN IFn Command Request (CANIFnCRQ) register. Reception of the message object begins as soon as a matching frame is available on the CAN bus. When the message handler stores a data frame in the message object, it stores the received Data Length Code and eight data bytes in the CANIFnDA1, CANIFnDA2, CANIFnDB1, and CANIFnDB2 register. Byte 0 of the CAN data frame is stored in DATA[7:0] in the CANIFnDA1 register. If the Data Length Code is less than 8, the remaining bytes of the message object are overwritten by unspecified values. The CAN mask registers can be used to allow groups of data frames to be received by a message object. The CAN mask registers, CANIFnMSKn, configure which groups of frames are received by a message object. The UMASK bit in the CANIFnMCTL register enables the MSK bits in the CANIFnMSKn register to filter which frames are received. The MXTD bit in the CANIFnMSK2 register should be set if only 29-bit extended identifiers are expected by this message object. 17.3.11 Handling of Received Message Objects The CPU may read a received message any time via the CAN Interface registers because the data consistency is guaranteed by the message handler state machine. Typically, the CPU first writes 0x007F to the CANIFnCMSK register and then writes the number of the message object to the CANIFnCRQ register. That combination transfers the whole received message from the message RAM into the Message Buffer registers (CANIFnMSKn, CANIFnARBn, and CANIFnMCTL). Additionally, the NEWDAT and INTPND bits are cleared in the message RAM, acknowledging that the message has been read and clearing the pending interrupt generated by this message object. If the message object uses masks for acceptance filtering, the CANIFnARBn registers show the full, unmasked ID for the received message. 1082 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller The NEWDAT bit in the CANIFnMCTL register shows whether a new message has been received since the last time this message object was read. The MSGLST bit in the CANIFnMCTL register shows whether more than one message has been received since the last time this message object was read. MSGLST is not automatically cleared, and should be cleared by software after reading its status. Using a remote frame, the CPU may request new data from another CAN node on the CAN bus. Setting the TXRQST bit of a receive object causes the transmission of a remote frame with the receive object's identifier. This remote frame triggers the other CAN node to start the transmission of the matching data frame. If the matching data frame is received before the remote frame could be transmitted, the TXRQST bit is automatically reset. This prevents the possible loss of data when the other device on the CAN bus has already transmitted the data slightly earlier than expected. 17.3.11.1 Configuration of a FIFO Buffer With the exception of the EOB bit in the CANIFnMCTL register, the configuration of receive message objects belonging to a FIFO buffer is the same as the configuration of a single receive message object (see “Configuring a Receive Message Object” on page 1081). To concatenate two or more message objects into a FIFO buffer, the identifiers and masks (if used) of these message objects have to be programmed to matching values. Due to the implicit priority of the message objects, the message object with the lowest message object number is the first message object in a FIFO buffer. The EOB bit of all message objects of a FIFO buffer except the last one must be cleared. The EOB bit of the last message object of a FIFO buffer is set, indicating it is the last entry in the buffer. 17.3.11.2 Reception of Messages with FIFO Buffers Received messages with identifiers matching to a FIFO buffer are stored starting with the message object with the lowest message number. When a message is stored into a message object of a FIFO buffer, the NEWDAT of the CANIFnMCTL register bit of this message object is set. By setting NEWDAT while EOB is clear, the message object is locked and cannot be written to by the message handler until the CPU has cleared the NEWDAT bit. Messages are stored into a FIFO buffer until the last message object of this FIFO buffer is reached. Until all of the preceding message objects have been released by clearing the NEWDAT bit, all further messages for this FIFO buffer are written into the last message object of the FIFO buffer and therefore overwrite previous messages. 17.3.11.3 Reading from a FIFO Buffer When the CPU transfers the contents of a message object from a FIFO buffer by writing its number to the CANIFnCRQ register, the TXRQST and CLRINTPND bits in the CANIFnCMSK register should be set such that the NEWDAT and INTPEND bits in the CANIFnMCTL register are cleared after the read. The values of these bits in the CANIFnMCTL register always reflect the status of the message object before the bits are cleared. To assure the correct function of a FIFO buffer, the CPU should read out the message objects starting with the message object with the lowest message number. When reading from the FIFO buffer, the user should be aware that a new received message could be placed in the location of any message object for which the NEWDAT bit of the CANIFnMCTL register is clear. As a result, the order of the received messages in the FIFO is not guaranteed. Figure 17-3 on page 1084 shows how a set of message objects which are concatenated to a FIFO Buffer can be handled by the CPU. November 08, 2011 1083 Texas Instruments-Advance Information Controller Area Network (CAN) Module Figure 17-3. Message Objects in a FIFO Buffer START Message Interrupt Read Interrupt Pointer 0x0000 Case Interrupt Pointer else 0x8000 END Status Change Interrupt Handling MNUM = Interrupt Pointer Write MNUM to IFn Command Request (Read Message to IFn Registers, Reset NEWDAT = 0, Reset INTPND = 0 Read IFn Message Control Yes No NEWDAT = 1 Read Data from IFn Data A,B EOB = 1 Yes No MNUM = MNUM + 1 17.3.12 Handling of Interrupts If several interrupts are pending, the CAN Interrupt (CANINT) register points to the pending interrupt with the highest priority, disregarding their chronological order. The status interrupt has the highest 1084 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller priority. Among the message interrupts, the message object's interrupt with the lowest message number has the highest priority. A message interrupt is cleared by clearing the message object's INTPND bit in the CANIFnMCTL register or by reading the CAN Status (CANSTS) register. The status Interrupt is cleared by reading the CANSTS register. The interrupt identifier INTID in the CANINT register indicates the cause of the interrupt. When no interrupt is pending, the register reads as 0x0000. If the value of the INTID field is different from 0, then an interrupt is pending. If the IE bit is set in the CANCTL register, the interrupt line to the interrupt controller is active. The interrupt line remains active until the INTID field is 0, meaning that all interrupt sources have been cleared (the cause of the interrupt is reset), or until IE is cleared, which disables interrupts from the CAN controller. The INTID field of the CANINT register points to the pending message interrupt with the highest interrupt priority. The SIE bit in the CANCTL register controls whether a change of the RXOK, TXOK, and LEC bits in the CANSTS register can cause an interrupt. The EIE bit in the CANCTLregister controls whether a change of the BOFF and EWARN bits in the CANSTS register can cause an interrupt. The IE bit in the CANCTL register controls whether any interrupt from the CAN controller actually generates an interrupt to the interrupt controller. The CANINT register is updated even when the IE bit in the CANCTL register is clear, but the interrupt is not indicated to the CPU. A value of 0x8000 in the CANINT register indicates that an interrupt is pending because the CAN module has updated, but not necessarily changed, the CANSTS register, indicating that either an error or status interrupt has been generated. A write access to the CANSTS register can clear the RXOK, TXOK, and LEC bits in that same register; however, the only way to clear the source of a status interrupt is to read the CANSTS register. The source of an interrupt can be determined in two ways during interrupt handling. The first is to read the INTID bit in the CANINT register to determine the highest priority interrupt that is pending, and the second is to read the CAN Message Interrupt Pending (CANMSGnINT) register to see all of the message objects that have pending interrupts. An interrupt service routine reading the message that is the source of the interrupt may read the message and clear the message object's INTPND bit at the same time by setting the CLRINTPND bit in the CANIFnCMSK register. Once the INTPND bit has been cleared, the CANINT register contains the message number for the next message object with a pending interrupt. 17.3.13 Test Mode A Test Mode is provided which allows various diagnostics to be performed. Test Mode is entered by setting the TEST bit in the CANCTL register. Once in Test Mode, the TX[1:0], LBACK, SILENT and BASIC bits in the CAN Test (CANTST) register can be used to put the CAN controller into the various diagnostic modes. The RX bit in the CANTST register allows monitoring of the CANnRX signal. All CANTST register functions are disabled when the TEST bit is cleared. 17.3.13.1 Silent Mode Silent Mode can be used to analyze the traffic on a CAN bus without affecting it by the transmission of dominant bits (Acknowledge Bits, Error Frames). The CAN Controller is put in Silent Mode setting the SILENT bit in the CANTST register. In Silent Mode, the CAN controller is able to receive valid data frames and valid remote frames, but it sends only recessive bits on the CAN bus and cannot start a transmission. If the CAN Controller is required to send a dominant bit (ACK bit, overload flag, or active error flag), the bit is rerouted internally so that the CAN Controller monitors this dominant bit, although the CAN bus remains in recessive state. November 08, 2011 1085 Texas Instruments-Advance Information Controller Area Network (CAN) Module 17.3.13.2 Loopback Mode Loopback mode is useful for self-test functions. In Loopback Mode, the CAN Controller internally routes the CANnTX signal on to the CANnRX signal and treats its own transmitted messages as received messages and stores them (if they pass acceptance filtering) into the message buffer. The CAN Controller is put in Loopback Mode by setting the LBACK bit in the CANTST register. To be independent from external stimulation, the CAN Controller ignores acknowledge errors (a recessive bit sampled in the acknowledge slot of a data/remote frame) in Loopback Mode. The actual value of the CANnRX signal is disregarded by the CAN Controller. The transmitted messages can be monitored on the CANnTX signal. 17.3.13.3 Loopback Combined with Silent Mode Loopback Mode and Silent Mode can be combined to allow the CAN Controller to be tested without affecting a running CAN system connected to the CANnTX and CANnRX signals. In this mode, the CANnRX signal is disconnected from the CAN Controller and the CANnTX signal is held recessive. This mode is enabled by setting both the LBACK and SILENT bits in the CANTST register. 17.3.13.4 Basic Mode Basic Mode allows the CAN Controller to be operated without the Message RAM. In Basic Mode, The CANIF1 registers are used as the transmit buffer. The transmission of the contents of the IF1 registers is requested by setting the BUSY bit of the CANIF1CRQ register. The CANIF1 registers are locked while the BUSY bit is set. The BUSY bit indicates that a transmission is pending. As soon the CAN bus is idle, the CANIF1 registers are loaded into the shift register of the CAN Controller and transmission is started. When the transmission has completed, the BUSY bit is cleared and the locked CANIF1 registers are released. A pending transmission can be aborted at any time by clearing the BUSY bit in the CANIF1CRQ register while the CANIF1 registers are locked. If the CPU has cleared the BUSY bit, a possible retransmission in case of lost arbitration or an error is disabled. The CANIF2 Registers are used as a receive buffer. After the reception of a message, the contents of the shift register are stored in the CANIF2 registers, without any acceptance filtering. Additionally, the actual contents of the shift register can be monitored during the message transfer. Each time a read message object is initiated by setting the BUSY bit of the CANIF2CRQ register, the contents of the shift register are stored into the CANIF2 registers. In Basic Mode, all message-object-related control and status bits and of the control bits of the CANIFnCMSK registers are not evaluated. The message number of the CANIFnCRQ registers is also not evaluated. In the CANIF2MCTL register, the NEWDAT and MSGLST bits retain their function, the DLC[3:0] field shows the received DLC, the other control bits are cleared. Basic Mode is enabled by setting the BASIC bit in the CANTST register. 17.3.13.5 Transmit Control Software can directly override control of the CANnTX signal in four different ways. ■ CANnTX is controlled by the CAN Controller ■ The sample point is driven on the CANnTX signal to monitor the bit timing ■ CANnTX drives a low value ■ CANnTX drives a high value 1086 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller The last two functions, combined with the readable CAN receive pin CANnRX, can be used to check the physical layer of the CAN bus. The Transmit Control function is enabled by programming the TX[1:0] field in the CANTST register. The three test functions for the CANnTX signal interfere with all CAN protocol functions. TX[1:0] must be cleared when CAN message transfer or Loopback Mode, Silent Mode, or Basic Mode are selected. 17.3.14 Bit Timing Configuration Error Considerations Even if minor errors in the configuration of the CAN bit timing do not result in immediate failure, the performance of a CAN network can be reduced significantly. In many cases, the CAN bit synchronization amends a faulty configuration of the CAN bit timing to such a degree that only occasionally an error frame is generated. In the case of arbitration, however, when two or more CAN nodes simultaneously try to transmit a frame, a misplaced sample point may cause one of the transmitters to become error passive. The analysis of such sporadic errors requires a detailed knowledge of the CAN bit synchronization inside a CAN node and of the CAN nodes' interaction on the CAN bus. 17.3.15 Bit Time and Bit Rate The CAN system supports bit rates in the range of lower than 1 Kbps up to 1000 Kbps. Each member of the CAN network has its own clock generator. The timing parameter of the bit time can be configured individually for each CAN node, creating a common bit rate even though the CAN nodes' oscillator periods may be different. Because of small variations in frequency caused by changes in temperature or voltage and by deteriorating components, these oscillators are not absolutely stable. As long as the variations remain inside a specific oscillator's tolerance range, the CAN nodes are able to compensate for the different bit rates by periodically resynchronizing to the bit stream. According to the CAN specification, the bit time is divided into four segments (see Figure 17-4 on page 1088): the Synchronization Segment, the Propagation Time Segment, the Phase Buffer Segment 1, and the Phase Buffer Segment 2. Each segment consists of a specific, programmable number of time quanta (see Table 17-3 on page 1088). The length of the time quantum (tq), which is the basic time unit of the bit time, is defined by the CAN controller's input clock (fsys) and the Baud Rate Prescaler (BRP): tq = BRP / fsys The fsys input clock is the system clock frequency as configured by the RCC or RCC2 registers (see page 280 or page 289). The Synchronization Segment Sync is that part of the bit time where edges of the CAN bus level are expected to occur; the distance between an edge that occurs outside of Sync and the Sync is called the phase error of that edge. The Propagation Time Segment Prop is intended to compensate for the physical delay times within the CAN network. The Phase Buffer Segments Phase1 and Phase2 surround the Sample Point. The (Re-)Synchronization Jump Width (SJW) defines how far a resynchronization may move the Sample Point inside the limits defined by the Phase Buffer Segments to compensate for edge phase errors. A given bit rate may be met by different bit-time configurations, but for the proper function of the CAN network, the physical delay times and the oscillator's tolerance range have to be considered. November 08, 2011 1087 Texas Instruments-Advance Information Controller Area Network (CAN) Module Figure 17-4. CAN Bit Time Nominal CAN Bit Time a b TSEG1 Sync Prop TSEG2 Phase1 c 1 Time Quantum q) (tq Phase2 Sample Point a. TSEG1 = Prop + Phase1 b. TSEG2 = Phase2 c. Phase1 = Phase2 or Phase1 + 1 = Phase2 a Table 17-3. CAN Protocol Ranges Parameter Range Remark BRP [1 .. 64] Defines the length of the time quantum tq. The CANBRPE register can be used to extend the range to 1024. Sync 1 tq Fixed length, synchronization of bus input to system clock Prop [1 .. 8] tq Compensates for the physical delay times Phase1 [1 .. 8] tq May be lengthened temporarily by synchronization Phase2 [1 .. 8] tq May be shortened temporarily by synchronization SJW [1 .. 4] tq May not be longer than either Phase Buffer Segment a. This table describes the minimum programmable ranges required by the CAN protocol. The bit timing configuration is programmed in two register bytes in the CANBIT register. In the CANBIT register, the four components TSEG2, TSEG1, SJW, and BRP have to be programmed to a numerical value that is one less than its functional value; so instead of values in the range of [1..n], values in the range of [0..n-1] are programmed. That way, for example, SJW (functional range of [1..4]) is represented by only two bits in the SJW bit field. Table 17-4 shows the relationship between the CANBIT register values and the parameters. Table 17-4. CANBIT Register Values CANBIT Register Field Setting TSEG2 Phase2 - 1 TSEG1 Prop + Phase1 - 1 SJW SJW - 1 BRP BRP Therefore, the length of the bit time is (programmed values): [TSEG1 + TSEG2 + 3] × tq or (functional values): [Sync + Prop + Phase1 + Phase2] × tq The data in the CANBIT register is the configuration input of the CAN protocol controller. The baud rate prescaler (configured by the BRP field) defines the length of the time quantum, the basic time 1088 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller unit of the bit time; the bit timing logic (configured by TSEG1, TSEG2, and SJW) defines the number of time quanta in the bit time. The processing of the bit time, the calculation of the position of the sample point, and occasional synchronizations are controlled by the CAN controller and are evaluated once per time quantum. The CAN controller translates messages to and from frames. In addition, the controller generates and discards the enclosing fixed format bits, inserts and extracts stuff bits, calculates and checks the CRC code, performs the error management, and decides which type of synchronization is to be used. The bit value is received or transmitted at the sample point. The information processing time (IPT) is the time after the sample point needed to calculate the next bit to be transmitted on the CAN bus. The IPT includes any of the following: retrieving the next data bit, handling a CRC bit, determining if bit stuffing is required, generating an error flag or simply going idle. The IPT is application-specific but may not be longer than 2 tq; the CAN's IPT is 0 tq. Its length is the lower limit of the programmed length of Phase2. In case of synchronization, Phase2 may be shortened to a value less than IPT, which does not affect bus timing. 17.3.16 Calculating the Bit Timing Parameters Usually, the calculation of the bit timing configuration starts with a required bit rate or bit time. The resulting bit time (1/bit rate) must be an integer multiple of the system clock period. The bit time may consist of 4 to 25 time quanta. Several combinations may lead to the required bit time, allowing iterations of the following steps. The first part of the bit time to be defined is Prop. Its length depends on the delay times measured in the system. A maximum bus length as well as a maximum node delay has to be defined for expandable CAN bus systems. The resulting time for Prop is converted into time quanta (rounded up to the nearest integer multiple of tq). Sync is 1 tq long (fixed), which leaves (bit time - Prop - 1) tq for the two Phase Buffer Segments. If the number of remaining tq is even, the Phase Buffer Segments have the same length, that is, Phase2 = Phase1, else Phase2 = Phase1 + 1. The minimum nominal length of Phase2 has to be regarded as well. Phase2 may not be shorter than the CAN controller's Information Processing Time, which is, depending on the actual implementation, in the range of [0..2] tq. The length of the synchronization jump width is set to the least of 4, Phase1 or Phase2. The oscillator tolerance range necessary for the resulting configuration is calculated by the formula given below: (1 − df ) × fnom ≤ fosc ≤ (1 + df ) × fnom where: df ≤ (Phase _ seg1, Phase _ seg2) min 2 × (13 × tbit − Phase _ Seg 2) ■ df = Maximum tolerance of oscillator frequency ■ fosc Actual=oscillator df =max 2 × dffrequency × fnom ■ fnom = Nominal oscillator frequency Maximum frequency tolerance must take into account the following formulas: November 08, 2011 1089 Texas Instruments-Advance Information Controller Area Network (CAN) Module − )df × fnom ≤ fosc + )df × fnom (1 −(1df × )fnom ≤ fosc ≤ (1≤ +(1df × )fnom (Phase _ seg 1, Phase _ seg 2) min (Phase _ seg 1, Phase _ seg 2) min df df ≤ ≤ 2 × (13 × tbit − Phase _ Seg 2) 2 × (13 × tbit − Phase _ Seg 2) × df × fnom df df maxmax = 2=× 2df × fnom where: ■ Phase1 and Phase2 are from Table 17-3 on page 1088 ■ tbit = Bit Time ■ dfmax = Maximum difference between two oscillators If more than one configuration is possible, that configuration allowing the highest oscillator tolerance range should be chosen. CAN nodes with different system clocks require different configurations to come to the same bit rate. The calculation of the propagation time in the CAN network, based on the nodes with the longest delay times, is done once for the whole network. The CAN system's oscillator tolerance range is limited by the node with the lowest tolerance range. The calculation may show that bus length or bit rate have to be decreased or that the oscillator frequencies' stability has to be increased in order to find a protocol-compliant configuration of the CAN bit timing. 17.3.16.1 Example for Bit Timing at High Baud Rate In this example, the frequency of CAN clock is 25 MHz, and the bit rate is 1 Mbps. bit time = 1 µs = n * tq = 5 * tq = 200 ns tq = (Baud rate Prescaler)/CAN Baud rate Prescaler = tq * CAN Baud rate Prescaler = 200E-9 * tq Clock Clock 25E6 = 5 tSync = 1 * tq = 200 ns \\fixed at 1 time quanta delay delay delay tProp \\400 is next integer multiple of tq of bus driver 50 ns of receiver circuit 30 ns of bus line (40m) 220 ns 400 ns = 2 * tq bit time = tSync + bit time = tSync + tPhase 1 + tPhase2 tPhase 1 + tPhase2 tPhase 1 + tPhase2 tPhase1 = 1 * tq tPhase2 = 1 * tq tTSeg1 + tTSeg2 = 5 * tq tProp + tPhase 1 + tPhase2 = bit time - tSync - tProp = (5 * tq) - (1 * tq) - (2 * tq) = 2 * tq \\tPhase2 = tPhase1 1090 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller tTSeg1 = tProp + tPhase1 tTSeg1 = (2 * tq) + (1 * tq) tTSeg1 = 3 * tq tTSeg2 = tPhase2 tTSeg2 = (Information Processing Time + 1) * tq tTSeg2 = 1 * tq \\Assumes IPT=0 tSJW = 1 * tq \\Least of 4, Phase1 and Phase2 In the above example, the bit field values for the CANBIT register are: = TSeg2 -1 TSEG2 = 1-1 =0 = TSeg1 -1 TSEG1 = 3-1 =2 = SJW -1 SJW = 1-1 =0 = Baud rate prescaler - 1 BRP = 5-1 =4 The final value programmed into the CANBIT register = 0x0204. 17.3.16.2 Example for Bit Timing at Low Baud Rate In this example, the frequency of the CAN clock is 50 MHz, and the bit rate is 100 Kbps. bit time = 10 µs = n * tq = 10 * tq tq = 1 µs tq = (Baud rate Prescaler)/CAN Clock Baud rate Prescaler = tq * CAN Clock Baud rate Prescaler = 1E-6 * 50E6 = 50 tSync = 1 * tq = 1 µs \\fixed at 1 time quanta delay delay delay tProp \\1 µs is next integer multiple of tq of bus driver 200 ns of receiver circuit 80 ns of bus line (40m) 220 ns 1 µs = 1 * tq bit time = tSync + bit time = tSync + tPhase 1 + tPhase2 tPhase 1 + tPhase2 tPhase 1 + tPhase2 tPhase1 = 4 * tq tPhase2 = 4 * tq tTSeg1 + tTSeg2 = 10 * tq tProp + tPhase 1 + tPhase2 = bit time - tSync - tProp = (10 * tq) - (1 * tq) - (1 * tq) = 8 * tq \\tPhase1 = tPhase2 November 08, 2011 1091 Texas Instruments-Advance Information Controller Area Network (CAN) Module tTSeg1 tTSeg1 tTSeg1 tTSeg2 tTSeg2 tTSeg2 = = = = = = tProp + tPhase1 (1 * tq) + (4 * tq) 5 * tq tPhase2 (Information Processing Time + 4) × tq 4 * tq \\Assumes IPT=0 tSJW = 4 * tq \\Least of 4, Phase1, and Phase2 = TSeg2 -1 TSEG2 = 4-1 =3 = TSeg1 -1 TSEG1 = 5-1 =4 = SJW -1 SJW = 4-1 =3 = Baud rate prescaler - 1 BRP = 50-1 =49 The final value programmed into the CANBIT register = 0x34F1. 17.4 Register Map Table 17-5 on page 1092 lists the registers. All addresses given are relative to the CAN base address of: ■ CAN0: 0x4004.0000 ■ CAN1: 0x4004.1000 Note that the CAN controller clock must be enabled before the registers can be programmed (see page 401). There must be a delay of 3 system clocks after the CAN module clock is enabled before any CAN module registers are accessed. Table 17-5. CAN Register Map Offset Name Type Reset Description See page 0x000 CANCTL R/W 0x0000.0001 CAN Control 1095 0x004 CANSTS R/W 0x0000.0000 CAN Status 1097 0x008 CANERR RO 0x0000.0000 CAN Error Counter 1100 0x00C CANBIT R/W 0x0000.2301 CAN Bit Timing 1101 0x010 CANINT RO 0x0000.0000 CAN Interrupt 1102 0x014 CANTST R/W 0x0000.0000 CAN Test 1103 0x018 CANBRPE R/W 0x0000.0000 CAN Baud Rate Prescaler Extension 1105 0x020 CANIF1CRQ R/W 0x0000.0001 CAN IF1 Command Request 1106 1092 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 17-5. CAN Register Map (continued) Description See page 0x0000.0000 CAN IF1 Command Mask 1107 R/W 0x0000.FFFF CAN IF1 Mask 1 1110 CANIF1MSK2 R/W 0x0000.FFFF CAN IF1 Mask 2 1111 0x030 CANIF1ARB1 R/W 0x0000.0000 CAN IF1 Arbitration 1 1113 0x034 CANIF1ARB2 R/W 0x0000.0000 CAN IF1 Arbitration 2 1114 0x038 CANIF1MCTL R/W 0x0000.0000 CAN IF1 Message Control 1116 0x03C CANIF1DA1 R/W 0x0000.0000 CAN IF1 Data A1 1119 0x040 CANIF1DA2 R/W 0x0000.0000 CAN IF1 Data A2 1119 0x044 CANIF1DB1 R/W 0x0000.0000 CAN IF1 Data B1 1119 0x048 CANIF1DB2 R/W 0x0000.0000 CAN IF1 Data B2 1119 0x080 CANIF2CRQ R/W 0x0000.0001 CAN IF2 Command Request 1106 0x084 CANIF2CMSK R/W 0x0000.0000 CAN IF2 Command Mask 1107 0x088 CANIF2MSK1 R/W 0x0000.FFFF CAN IF2 Mask 1 1110 0x08C CANIF2MSK2 R/W 0x0000.FFFF CAN IF2 Mask 2 1111 0x090 CANIF2ARB1 R/W 0x0000.0000 CAN IF2 Arbitration 1 1113 0x094 CANIF2ARB2 R/W 0x0000.0000 CAN IF2 Arbitration 2 1114 0x098 CANIF2MCTL R/W 0x0000.0000 CAN IF2 Message Control 1116 0x09C CANIF2DA1 R/W 0x0000.0000 CAN IF2 Data A1 1119 0x0A0 CANIF2DA2 R/W 0x0000.0000 CAN IF2 Data A2 1119 0x0A4 CANIF2DB1 R/W 0x0000.0000 CAN IF2 Data B1 1119 0x0A8 CANIF2DB2 R/W 0x0000.0000 CAN IF2 Data B2 1119 0x100 CANTXRQ1 RO 0x0000.0000 CAN Transmission Request 1 1120 0x104 CANTXRQ2 RO 0x0000.0000 CAN Transmission Request 2 1120 0x120 CANNWDA1 RO 0x0000.0000 CAN New Data 1 1121 0x124 CANNWDA2 RO 0x0000.0000 CAN New Data 2 1121 0x140 CANMSG1INT RO 0x0000.0000 CAN Message 1 Interrupt Pending 1122 0x144 CANMSG2INT RO 0x0000.0000 CAN Message 2 Interrupt Pending 1122 0x160 CANMSG1VAL RO 0x0000.0000 CAN Message 1 Valid 1123 0x164 CANMSG2VAL RO 0x0000.0000 CAN Message 2 Valid 1123 Offset Name Type Reset 0x024 CANIF1CMSK R/W 0x028 CANIF1MSK1 0x02C 17.5 CAN Register Descriptions The remainder of this section lists and describes the CAN registers, in numerical order by address offset. There are two sets of Interface Registers that are used to access the Message Objects in November 08, 2011 1093 Texas Instruments-Advance Information Controller Area Network (CAN) Module the Message RAM: CANIF1x and CANIF2x. The function of the two sets are identical and are used to queue transactions. 1094 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 1: CAN Control (CANCTL), offset 0x000 This control register initializes the module and enables test mode and interrupts. The bus-off recovery sequence (see CAN Specification Rev. 2.0) cannot be shortened by setting or clearing INIT. If the device goes bus-off, it sets INIT, stopping all bus activities. Once INIT has been cleared by the CPU, the device then waits for 129 occurrences of Bus Idle (129 * 11 consecutive High bits) before resuming normal operations. At the end of the bus-off recovery sequence, the Error Management Counters are reset. During the waiting time after INIT is cleared, each time a sequence of 11 High bits has been monitored, a BITERROR0 code is written to the CANSTS register (the LEC field = 0x5), enabling the CPU to readily check whether the CAN bus is stuck Low or continuously disturbed, and to monitor the proceeding of the bus-off recovery sequence. CAN Control (CANCTL) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x000 Type R/W, reset 0x0000.0001 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 TEST CCE DAR reserved EIE SIE IE INIT R/W 0 R/W 0 R/W 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 1 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 TEST R/W 0 6 5 CCE DAR R/W R/W 0 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Test Mode Enable Value Description 0 The CAN controller is operating normally. 1 The CAN controller is in test mode. Configuration Change Enable Value Description 0 Write accesses to the CANBIT register are not allowed. 1 Write accesses to the CANBIT register are allowed if the INIT bit is 1. Disable Automatic-Retransmission Value Description 0 Auto-retransmission of disturbed messages is enabled. 1 Auto-retransmission is disabled. November 08, 2011 1095 Texas Instruments-Advance Information Controller Area Network (CAN) Module Bit/Field Name Type Reset 4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 EIE R/W 0 Error Interrupt Enable 2 1 0 SIE IE INIT R/W R/W R/W 0 0 1 Description Value Description 0 No error status interrupt is generated. 1 A change in the BOFF or EWARN bits in the CANSTS register generates an interrupt. Status Interrupt Enable Value Description 0 No status interrupt is generated. 1 An interrupt is generated when a message has successfully been transmitted or received, or a CAN bus error has been detected. A change in the TXOK, RXOK or LEC bits in the CANSTS register generates an interrupt. CAN Interrupt Enable Value Description 0 Interrupts disabled. 1 Interrupts enabled. Initialization Value Description 0 Normal operation. 1 Initialization started. 1096 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 2: CAN Status (CANSTS), offset 0x004 Important: This register is read-sensitive. See the register description for details. The status register contains information for interrupt servicing such as Bus-Off, error count threshold, and error types. The LEC field holds the code that indicates the type of the last error to occur on the CAN bus. This field is cleared when a message has been transferred (reception or transmission) without error. The unused error code 0x7 may be written by the CPU to manually set this field to an invalid error so that it can be checked for a change later. An error interrupt is generated by the BOFF and EWARN bits, and a status interrupt is generated by the RXOK, TXOK, and LEC bits, if the corresponding enable bits in the CAN Control (CANCTL) register are set. A change of the EPASS bit or a write to the RXOK, TXOK, or LEC bits does not generate an interrupt. Reading the CAN Status (CANSTS) register clears the CAN Interrupt (CANINT) register, if it is pending. CAN Status (CANSTS) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x004 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 BOFF RO 0 6 EWARN RO 0 RO 0 7 6 5 4 3 BOFF EWARN EPASS RXOK TXOK RO 0 RO 0 RO 0 R/W 0 R/W 0 RO 0 LEC R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Bus-Off Status Value Description 0 The CAN controller is not in bus-off state. 1 The CAN controller is in bus-off state. Warning Status Value Description 0 Both error counters are below the error warning limit of 96. 1 At least one of the error counters has reached the error warning limit of 96. November 08, 2011 1097 Texas Instruments-Advance Information Controller Area Network (CAN) Module Bit/Field Name Type Reset 5 EPASS RO 0 4 RXOK R/W 0 Description Error Passive Value Description 0 The CAN module is in the Error Active state, that is, the receive or transmit error count is less than or equal to 127. 1 The CAN module is in the Error Passive state, that is, the receive or transmit error count is greater than 127. Received a Message Successfully Value Description 0 Since this bit was last cleared, no message has been successfully received. 1 Since this bit was last cleared, a message has been successfully received, independent of the result of the acceptance filtering. This bit must be cleared by writing a 0 to it. 3 TXOK R/W 0 Transmitted a Message Successfully Value Description 0 Since this bit was last cleared, no message has been successfully transmitted. 1 Since this bit was last cleared, a message has been successfully transmitted error-free and acknowledged by at least one other node. This bit must be cleared by writing a 0 to it. 1098 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 2:0 LEC R/W 0x0 Description Last Error Code This is the type of the last error to occur on the CAN bus. Value Description 0x0 No Error 0x1 Stuff Error More than 5 equal bits in a sequence have occurred in a part of a received message where this is not allowed. 0x2 Format Error A fixed format part of the received frame has the wrong format. 0x3 ACK Error The message transmitted was not acknowledged by another node. 0x4 Bit 1 Error When a message is transmitted, the CAN controller monitors the data lines to detect any conflicts. When the arbitration field is transmitted, data conflicts are a part of the arbitration protocol. When other frame fields are transmitted, data conflicts are considered errors. A Bit 1 Error indicates that the device wanted to send a High level (logical 1) but the monitored bus value was Low (logical 0). 0x5 Bit 0 Error A Bit 0 Error indicates that the device wanted to send a Low level (logical 0), but the monitored bus value was High (logical 1). During bus-off recovery, this status is set each time a sequence of 11 High bits has been monitored. By checking for this status, software can monitor the proceeding of the bus-off recovery sequence without any disturbances to the bus. 0x6 CRC Error The CRC checksum was incorrect in the received message, indicating that the calculated value received did not match the calculated CRC of the data. 0x7 No Event When the LEC bit shows this value, no CAN bus event was detected since this value was written to the LEC field. November 08, 2011 1099 Texas Instruments-Advance Information Controller Area Network (CAN) Module Register 3: CAN Error Counter (CANERR), offset 0x008 This register contains the error counter values, which can be used to analyze the cause of an error. CAN Error Counter (CANERR) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x008 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RP Type Reset RO 0 REC TEC RO 0 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15 RP RO 0 14:8 REC RO 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Received Error Passive Value Description 0 The Receive Error counter is below the Error Passive level (127 or less). 1 The Receive Error counter has reached the Error Passive level (128 or greater). Receive Error Counter This field contains the state of the receiver error counter (0 to 127). 7:0 TEC RO 0x00 Transmit Error Counter This field contains the state of the transmit error counter (0 to 255). 1100 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 4: CAN Bit Timing (CANBIT), offset 0x00C This register is used to program the bit width and bit quantum. Values are programmed to the system clock frequency. This register is write-enabled by setting the CCE and INIT bits in the CANCTL register. See “Bit Time and Bit Rate” on page 1087 for more information. CAN Bit Timing (CANBIT) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x00C Type R/W, reset 0x0000.2301 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 R/W 0 R/W 0 R/W 0 R/W 1 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 R/W 1 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 1 reserved Type Reset TSEG2 reserved Type Reset RO 0 R/W 0 R/W 1 TSEG1 Bit/Field Name Type Reset 31:15 reserved RO 0x0000 14:12 TSEG2 R/W 0x2 SJW BRP Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Time Segment after Sample Point 0x00-0x07: The actual interpretation by the hardware of this value is such that one more than the value programmed here is used. So, for example, the reset value of 0x2 means that 3 (2+1) bit time quanta are defined for Phase2 (see Figure 17-4 on page 1088). The bit time quanta is defined by the BRP field. 11:8 TSEG1 R/W 0x3 Time Segment Before Sample Point 0x00-0x0F: The actual interpretation by the hardware of this value is such that one more than the value programmed here is used. So, for example, the reset value of 0x3 means that 4 (3+1) bit time quanta are defined for Phase1 (see Figure 17-4 on page 1088). The bit time quanta is defined by the BRP field. 7:6 SJW R/W 0x0 (Re)Synchronization Jump Width 0x00-0x03: The actual interpretation by the hardware of this value is such that one more than the value programmed here is used. During the start of frame (SOF), if the CAN controller detects a phase error (misalignment), it can adjust the length of TSEG2 or TSEG1 by the value in SJW. So the reset value of 0 adjusts the length by 1 bit time quanta. 5:0 BRP R/W 0x1 Baud Rate Prescaler The value by which the oscillator frequency is divided for generating the bit time quanta. The bit time is built up from a multiple of this quantum. 0x00-0x03F: The actual interpretation by the hardware of this value is such that one more than the value programmed here is used. BRP defines the number of CAN clock periods that make up 1 bit time quanta, so the reset value is 2 bit time quanta (1+1). The CANBRPE register can be used to further divide the bit time. November 08, 2011 1101 Texas Instruments-Advance Information Controller Area Network (CAN) Module Register 5: CAN Interrupt (CANINT), offset 0x010 This register indicates the source of the interrupt. If several interrupts are pending, the CAN Interrupt (CANINT) register points to the pending interrupt with the highest priority, disregarding the order in which the interrupts occurred. An interrupt remains pending until the CPU has cleared it. If the INTID field is not 0x0000 (the default) and the IE bit in the CANCTL register is set, the interrupt is active. The interrupt line remains active until the INTID field is cleared by reading the CANSTS register, or until the IE bit in the CANCTL register is cleared. Note: Reading the CAN Status (CANSTS) register clears the CAN Interrupt (CANINT) register, if it is pending. CAN Interrupt (CANINT) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x010 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset INTID Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 INTID RO 0x0000 Interrupt Identifier The number in this field indicates the source of the interrupt. Value Description 0x0000 No interrupt pending 0x0001-0x0020 Number of the message object that caused the interrupt 0x0021-0x7FFF Reserved 0x8000 Status Interrupt 0x8001-0xFFFF Reserved 1102 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 6: CAN Test (CANTST), offset 0x014 This register is used for self-test and external pin access. It is write-enabled by setting the TEST bit in the CANCTL register. Different test functions may be combined, however, CAN transfers are affected if the TX bits in this register are not zero. CAN Test (CANTST) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x014 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 LBACK SILENT BASIC RO 0 RO 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RX RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 RX RO 0 6:5 TX R/W 0x0 TX R/W 0 R/W 0 reserved RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Receive Observation Value Description 0 The CANnRx pin is low. 1 The CANnRx pin is high. Transmit Control Overrides control of the CANnTx pin. Value Description 0x0 CAN Module Control CANnTx is controlled by the CAN module; default operation 0x1 Sample Point The sample point is driven on the CANnTx signal. This mode is useful to monitor bit timing. 0x2 Driven Low CANnTx drives a low value. This mode is useful for checking the physical layer of the CAN bus. 0x3 Driven High CANnTx drives a high value. This mode is useful for checking the physical layer of the CAN bus. November 08, 2011 1103 Texas Instruments-Advance Information Controller Area Network (CAN) Module Bit/Field Name Type Reset 4 LBACK R/W 0 3 2 1:0 SILENT BASIC reserved R/W R/W RO 0 0 0x0 Description Loopback Mode Value Description 0 Loopback mode is disabled. 1 Loopback mode is enabled. In loopback mode, the data from the transmitter is routed into the receiver. Any data on the receive input is ignored. Silent Mode Value Description 0 Silent mode is disabled. 1 Silent mode is enabled. In silent mode, the CAN controller does not transmit data but instead monitors the bus. This mode is also known as Bus Monitor mode. Basic Mode Value Description 0 Basic mode is disabled. 1 Basic mode is enabled. In basic mode, software should use the CANIF1 registers as the transmit buffer and use the CANIF2 registers as the receive buffer. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1104 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 7: CAN Baud Rate Prescaler Extension (CANBRPE), offset 0x018 This register is used to further divide the bit time set with the BRP bit in the CANBIT register. It is write-enabled by setting the CCE bit in the CANCTL register. CAN Baud Rate Prescaler Extension (CANBRPE) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x018 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3:0 BRPE R/W 0x0 BRPE Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Baud Rate Prescaler Extension 0x00-0x0F: Extend the BRP bit in the CANBIT register to values up to 1023. The actual interpretation by the hardware is one more than the value programmed by BRPE (MSBs) and BRP (LSBs). November 08, 2011 1105 Texas Instruments-Advance Information Controller Area Network (CAN) Module Register 8: CAN IF1 Command Request (CANIF1CRQ), offset 0x020 Register 9: CAN IF2 Command Request (CANIF2CRQ), offset 0x080 A message transfer is started as soon as there is a write of the message object number to the MNUM field when the TXRQST bit in the CANIF1MCTL register is set. With this write operation, the BUSY bit is automatically set to indicate that a transfer between the CAN Interface Registers and the internal message RAM is in progress. After a wait time of 3 to 6 CAN_CLK periods, the transfer between the interface register and the message RAM completes, which then clears the BUSY bit. CAN IF1 Command Request (CANIF1CRQ) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x020 Type R/W, reset 0x0000.0001 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 1 reserved Type Reset BUSY Type Reset RO 0 reserved RO 0 MNUM Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15 BUSY RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Busy Flag Value Description 0 This bit is cleared when read/write action has finished. 1 This bit is set when a write occurs to the message number in this register. 14:6 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5:0 MNUM R/W 0x01 Message Number Selects one of the 32 message objects in the message RAM for data transfer. The message objects are numbered from 1 to 32. Value Description 0x00 Reserved 0 is not a valid message number; it is interpreted as 0x20, or object 32. 0x01-0x20 Message Number Indicates specified message object 1 to 32. 0x21-0x3F Reserved Not a valid message number; values are shifted and it is interpreted as 0x01-0x1F. 1106 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 10: CAN IF1 Command Mask (CANIF1CMSK), offset 0x024 Register 11: CAN IF2 Command Mask (CANIF2CMSK), offset 0x084 Reading the Command Mask registers provides status for various functions. Writing to the Command Mask registers specifies the transfer direction and selects which buffer registers are the source or target of the data transfer. Note that when a read from the message object buffer occurs when the WRNRD bit is clear and the CLRINTPND and/or NEWDAT bits are set, the interrupt pending and/or new data flags in the message object buffer are cleared. CAN IF1 Command Mask (CANIF1CMSK) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 2 1 0 DATAA DATAB R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 WRNRD R/W 0 6 MASK R/W 0 WRNRD MASK ARB R/W 0 R/W 0 R/W 0 RO 0 CONTROL CLRINTPND R/W 0 R/W 0 NEWDAT / TXRQST R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Write, Not Read Value Description 0 Transfer the data in the CAN message object specified by the the MNUM field in the CANIFnCRQ register into the CANIFn registers. 1 Transfer the data in the CANIFn registers to the CAN message object specified by the MNUM field in the CAN Command Request (CANIFnCRQ). Note: Interrupt pending and new data conditions in the message buffer can be cleared by reading from the buffer (WRNRD = 0) when the CLRINTPND and/or NEWDAT bits are set. Access Mask Bits Value Description 0 Mask bits unchanged. 1 Transfer IDMASK + DIR + MXTD of the message object into the Interface registers. November 08, 2011 1107 Texas Instruments-Advance Information Controller Area Network (CAN) Module Bit/Field Name Type Reset 5 ARB R/W 0 4 3 CONTROL CLRINTPND R/W R/W 0 0 Description Access Arbitration Bits Value Description 0 Arbitration bits unchanged. 1 Transfer ID + DIR + XTD + MSGVAL of the message object into the Interface registers. Access Control Bits Value Description 0 Control bits unchanged. 1 Transfer control bits from the CANIFnMCTL register into the Interface registers. Clear Interrupt Pending Bit The function of this bit depends on the configuration of the WRNRD bit. Value 0 Description If WRNRD is clear, the interrupt pending status is transferred from the message buffer into the CANIFnMCTL register. If WRNRD is set, the INTPND bit in the message object remains unchanged. 1 If WRNRD is clear, the interrupt pending status is cleared in the message buffer. Note the value of this bit that is transferred to the CANIFnMCTL register always reflects the status of the bits before clearing. If WRNRD is set, the INTPND bit is cleared in the message object. 2 NEWDAT / TXRQST R/W 0 NEWDAT / TXRQST Bit The function of this bit depends on the configuration of the WRNRD bit. Value 0 Description If WRNRD is clear, the value of the new data status is transferred from the message buffer into the CANIFnMCTL register. If WRNRD is set, a transmission is not requested. 1 If WRNRD is clear, the new data status is cleared in the message buffer. Note the value of this bit that is transferred to the CANIFnMCTL register always reflects the status of the bits before clearing. If WRNRD is set, a transmission is requested. Note that when this bit is set, the TXRQST bit in the CANIFnMCTL register is ignored. 1108 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 DATAA R/W 0 Description Access Data Byte 0 to 3 The function of this bit depends on the configuration of the WRNRD bit. Value Description 0 Data bytes 0-3 are unchanged. 1 If WRNRD is clear, transfer data bytes 0-3 in CANIFnDA1 and CANIFnDA2 to the message object. If WRNRD is set, transfer data bytes 0-3 in message object to CANIFnDA1 and CANIFnDA2. 0 DATAB R/W 0 Access Data Byte 4 to 7 The function of this bit depends on the configuration of the WRNRD bit as follows: Value Description 0 Data bytes 4-7 are unchanged. 1 If WRNRD is clear, transfer data bytes 4-7 in CANIFnDA1 and CANIFnDA2 to the message object. If WRNRD is set, transfer data bytes 4-7 in message object to CANIFnDA1 and CANIFnDA2. November 08, 2011 1109 Texas Instruments-Advance Information Controller Area Network (CAN) Module Register 12: CAN IF1 Mask 1 (CANIF1MSK1), offset 0x028 Register 13: CAN IF2 Mask 1 (CANIF2MSK1), offset 0x088 The mask information provided in this register accompanies the data (CANIFnDAn), arbitration information (CANIFnARBn), and control information (CANIFnMCTL) to the message object in the message RAM. The mask is used with the ID bit in the CANIFnARBn register for acceptance filtering. Additional mask information is contained in the CANIFnMSK2 register. CAN IF1 Mask 1 (CANIF1MSK1) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x028 Type R/W, reset 0x0000.FFFF 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset MSK Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 MSK R/W 0xFFFF Identifier Mask When using a 29-bit identifier, these bits are used for bits [15:0] of the ID. The MSK field in the CANIFnMSK2 register are used for bits [28:16] of the ID. When using an 11-bit identifier, these bits are ignored. Value Description 0 The corresponding identifier field (ID) in the message object cannot inhibit the match in acceptance filtering. 1 The corresponding identifier field (ID) is used for acceptance filtering. 1110 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 14: CAN IF1 Mask 2 (CANIF1MSK2), offset 0x02C Register 15: CAN IF2 Mask 2 (CANIF2MSK2), offset 0x08C This register holds extended mask information that accompanies the CANIFnMSK1 register. CAN IF1 Mask 2 (CANIF1MSK2) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x02C Type R/W, reset 0x0000.FFFF 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 MXTD MDIR reserved R/W 1 R/W 1 RO 1 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 R/W 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset Type Reset MSK Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15 MXTD R/W 1 14 13 MDIR reserved R/W RO 1 1 R/W 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Mask Extended Identifier Value Description 0 The extended identifier bit (XTD in the CANIFnARB2 register) has no effect on the acceptance filtering. 1 The extended identifier bit XTD is used for acceptance filtering. Mask Message Direction Value Description 0 The message direction bit (DIR in the CANIFnARB2 register) has no effect for acceptance filtering. 1 The message direction bit DIR is used for acceptance filtering. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1111 Texas Instruments-Advance Information Controller Area Network (CAN) Module Bit/Field Name Type Reset Description 12:0 MSK R/W 0xFF Identifier Mask When using a 29-bit identifier, these bits are used for bits [28:16] of the ID. The MSK field in the CANIFnMSK1 register are used for bits [15:0] of the ID. When using an 11-bit identifier, MSK[12:2] are used for bits [10:0] of the ID. Value Description 0 The corresponding identifier field (ID) in the message object cannot inhibit the match in acceptance filtering. 1 The corresponding identifier field (ID) is used for acceptance filtering. 1112 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 16: CAN IF1 Arbitration 1 (CANIF1ARB1), offset 0x030 Register 17: CAN IF2 Arbitration 1 (CANIF2ARB1), offset 0x090 These registers hold the identifiers for acceptance filtering. CAN IF1 Arbitration 1 (CANIF1ARB1) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x030 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset ID Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 ID R/W 0x0000 Message Identifier This bit field is used with the ID field in the CANIFnARB2 register to create the message identifier. When using a 29-bit identifier, bits 15:0 of the CANIFnARB1 register are [15:0] of the ID, while bits 12:0 of the CANIFnARB2 register are [28:16] of the ID. When using an 11-bit identifier, these bits are not used. November 08, 2011 1113 Texas Instruments-Advance Information Controller Area Network (CAN) Module Register 18: CAN IF1 Arbitration 2 (CANIF1ARB2), offset 0x034 Register 19: CAN IF2 Arbitration 2 (CANIF2ARB2), offset 0x094 These registers hold information for acceptance filtering. CAN IF1 Arbitration 2 (CANIF1ARB2) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x034 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 MSGVAL XTD DIR R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset Type Reset ID Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15 MSGVAL R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Message Valid Value Description 0 The message object is ignored by the message handler. 1 The message object is configured and ready to be considered by the message handler within the CAN controller. All unused message objects should have this bit cleared during initialization and before clearing the INIT bit in the CANCTL register. The MSGVAL bit must also be cleared before any of the following bits are modified or if the message object is no longer required: the ID fields in the CANIFnARBn registers, the XTD and DIR bits in the CANIFnARB2 register, or the DLC field in the CANIFnMCTL register. 14 XTD R/W 0 Extended Identifier Value Description 0 An 11-bit Standard Identifier is used for this message object. 1 A 29-bit Extended Identifier is used for this message object. 1114 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 13 DIR R/W 0 12:0 ID R/W 0x000 Description Message Direction Value Description 0 Receive. When the TXRQST bit in the CANIFnMCTL register is set, a remote frame with the identifier of this message object is received. On reception of a data frame with matching identifier, that message is stored in this message object. 1 Transmit. When the TXRQST bit in the CANIFnMCTL register is set, the respective message object is transmitted as a data frame. On reception of a remote frame with matching identifier, the TXRQST bit of this message object is set (if RMTEN=1). Message Identifier This bit field is used with the ID field in the CANIFnARB2 register to create the message identifier. When using a 29-bit identifier, ID[15:0] of the CANIFnARB1 register are [15:0] of the ID, while these bits, ID[12:0], are [28:16] of the ID. When using an 11-bit identifier, ID[12:2] are used for bits [10:0] of the ID. The ID field in the CANIFnARB1 register is ignored. November 08, 2011 1115 Texas Instruments-Advance Information Controller Area Network (CAN) Module Register 20: CAN IF1 Message Control (CANIF1MCTL), offset 0x038 Register 21: CAN IF2 Message Control (CANIF2MCTL), offset 0x098 This register holds the control information associated with the message object to be sent to the Message RAM. CAN IF1 Message Control (CANIF1MCTL) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x038 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 UMASK TXIE RXIE R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RMTEN TXRQST EOB R/W 0 R/W 0 R/W 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset NEWDAT MSGLST INTPND Type Reset R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:16 reserved RO 0x0000 15 NEWDAT R/W 0 14 MSGLST R/W 0 reserved RO 0 RO 0 DLC Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. New Data Value Description 0 No new data has been written into the data portion of this message object by the message handler since the last time this flag was cleared by the CPU. 1 The message handler or the CPU has written new data into the data portion of this message object. Message Lost Value Description 0 No message was lost since the last time this bit was cleared by the CPU. 1 The message handler stored a new message into this object when NEWDAT was set; the CPU has lost a message. This bit is only valid for message objects when the DIR bit in the CANIFnARB2 register is clear (receive). 13 INTPND R/W 0 Interrupt Pending Value Description 0 This message object is not the source of an interrupt. 1 This message object is the source of an interrupt. The interrupt identifier in the CANINT register points to this message object if there is not another interrupt source with a higher priority. 1116 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 12 UMASK R/W 0 11 10 9 8 TXIE RXIE RMTEN TXRQST R/W R/W R/W R/W 0 0 0 0 Description Use Acceptance Mask Value Description 0 Mask is ignored. 1 Use mask (MSK, MXTD, and MDIR bits in the CANIFnMSKn registers) for acceptance filtering. Transmit Interrupt Enable Value Description 0 The INTPND bit in the CANIFnMCTL register is unchanged after a successful transmission of a frame. 1 The INTPND bit in the CANIFnMCTL register is set after a successful transmission of a frame. Receive Interrupt Enable Value Description 0 The INTPND bit in the CANIFnMCTL register is unchanged after a successful reception of a frame. 1 The INTPND bit in the CANIFnMCTL register is set after a successful reception of a frame. Remote Enable Value Description 0 At the reception of a remote frame, the TXRQST bit in the CANIFnMCTL register is left unchanged. 1 At the reception of a remote frame, the TXRQST bit in the CANIFnMCTL register is set. Transmit Request Value Description 0 This message object is not waiting for transmission. 1 The transmission of this message object is requested and is not yet done. Note: If the WRNRD and TXRQST bits in the CANIFnCMSK register are set, this bit is ignored. November 08, 2011 1117 Texas Instruments-Advance Information Controller Area Network (CAN) Module Bit/Field Name Type Reset 7 EOB R/W 0 Description End of Buffer Value Description 0 Message object belongs to a FIFO Buffer and is not the last message object of that FIFO Buffer. 1 Single message object or last message object of a FIFO Buffer. This bit is used to concatenate two or more message objects (up to 32) to build a FIFO buffer. For a single message object (thus not belonging to a FIFO buffer), this bit must be set. 6:4 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3:0 DLC R/W 0x0 Data Length Code Value Description 0x0-0x8 Specifies the number of bytes in the data frame. 0x9-0xF Defaults to a data frame with 8 bytes. The DLC field in the CANIFnMCTL register of a message object must be defined the same as in all the corresponding objects with the same identifier at other nodes. When the message handler stores a data frame, it writes DLC to the value given by the received message. 1118 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 22: CAN IF1 Data A1 (CANIF1DA1), offset 0x03C Register 23: CAN IF1 Data A2 (CANIF1DA2), offset 0x040 Register 24: CAN IF1 Data B1 (CANIF1DB1), offset 0x044 Register 25: CAN IF1 Data B2 (CANIF1DB2), offset 0x048 Register 26: CAN IF2 Data A1 (CANIF2DA1), offset 0x09C Register 27: CAN IF2 Data A2 (CANIF2DA2), offset 0x0A0 Register 28: CAN IF2 Data B1 (CANIF2DB1), offset 0x0A4 Register 29: CAN IF2 Data B2 (CANIF2DB2), offset 0x0A8 These registers contain the data to be sent or that has been received. In a CAN data frame, data byte 0 is the first byte to be transmitted or received and data byte 7 is the last byte to be transmitted or received. In CAN's serial bit stream, the MSB of each byte is transmitted first. CAN IF1 Data A1 (CANIF1DA1) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x03C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset DATA Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 DATA R/W 0x0000 Data The CANIFnDA1 registers contain data bytes 1 and 0; CANIFnDA2 data bytes 3 and 2; CANIFnDB1 data bytes 5 and 4; and CANIFnDB2 data bytes 7 and 6. November 08, 2011 1119 Texas Instruments-Advance Information Controller Area Network (CAN) Module Register 30: CAN Transmission Request 1 (CANTXRQ1), offset 0x100 Register 31: CAN Transmission Request 2 (CANTXRQ2), offset 0x104 The CANTXRQ1 and CANTXRQ2 registers hold the TXRQST bits of the 32 message objects. By reading out these bits, the CPU can check which message object has a transmission request pending. The TXRQST bit of a specific message object can be changed by three sources: (1) the CPU via the CANIFnMCTL register, (2) the message handler state machine after the reception of a remote frame, or (3) the message handler state machine after a successful transmission. The CANTXRQ1 register contains the TXRQST bits of the first 16 message objects in the message RAM; the CANTXRQ2 register contains the TXRQST bits of the second 16 message objects. CAN Transmission Request 1 (CANTXRQ1) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x100 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 TXRQST Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 TXRQST RO 0x0000 Transmission Request Bits Value Description 0 The corresponding message object is not waiting for transmission. 1 The transmission of the corresponding message object is requested and is not yet done. 1120 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 32: CAN New Data 1 (CANNWDA1), offset 0x120 Register 33: CAN New Data 2 (CANNWDA2), offset 0x124 The CANNWDA1 and CANNWDA2 registers hold the NEWDAT bits of the 32 message objects. By reading these bits, the CPU can check which message object has its data portion updated. The NEWDAT bit of a specific message object can be changed by three sources: (1) the CPU via the CANIFnMCTL register, (2) the message handler state machine after the reception of a data frame, or (3) the message handler state machine after a successful transmission. The CANNWDA1 register contains the NEWDAT bits of the first 16 message objects in the message RAM; the CANNWDA2 register contains the NEWDAT bits of the second 16 message objects. CAN New Data 1 (CANNWDA1) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x120 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 NEWDAT Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 NEWDAT RO 0x0000 New Data Bits Value Description 0 No new data has been written into the data portion of the corresponding message object by the message handler since the last time this flag was cleared by the CPU. 1 The message handler or the CPU has written new data into the data portion of the corresponding message object. November 08, 2011 1121 Texas Instruments-Advance Information Controller Area Network (CAN) Module Register 34: CAN Message 1 Interrupt Pending (CANMSG1INT), offset 0x140 Register 35: CAN Message 2 Interrupt Pending (CANMSG2INT), offset 0x144 The CANMSG1INT and CANMSG2INT registers hold the INTPND bits of the 32 message objects. By reading these bits, the CPU can check which message object has an interrupt pending. The INTPND bit of a specific message object can be changed through two sources: (1) the CPU via the CANIFnMCTL register, or (2) the message handler state machine after the reception or transmission of a frame. This field is also encoded in the CANINT register. The CANMSG1INT register contains the INTPND bits of the first 16 message objects in the message RAM; the CANMSG2INT register contains the INTPND bits of the second 16 message objects. CAN Message 1 Interrupt Pending (CANMSG1INT) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x140 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset INTPND Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 INTPND RO 0x0000 Interrupt Pending Bits Value Description 0 The corresponding message object is not the source of an interrupt. 1 The corresponding message object is the source of an interrupt. 1122 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 36: CAN Message 1 Valid (CANMSG1VAL), offset 0x160 Register 37: CAN Message 2 Valid (CANMSG2VAL), offset 0x164 The CANMSG1VAL and CANMSG2VAL registers hold the MSGVAL bits of the 32 message objects. By reading these bits, the CPU can check which message object is valid. The message valid bit of a specific message object can be changed with the CANIFnARB2 register. The CANMSG1VAL register contains the MSGVAL bits of the first 16 message objects in the message RAM; the CANMSG2VAL register contains the MSGVAL bits of the second 16 message objects in the message RAM. CAN Message 1 Valid (CANMSG1VAL) CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 Offset 0x160 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 MSGVAL Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 MSGVAL RO 0x0000 Message Valid Bits Value Description 0 The corresponding message object is not configured and is ignored by the message handler. 1 The corresponding message object is configured and should be considered by the message handler. November 08, 2011 1123 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller 18 Universal Serial Bus (USB) Controller ® The Stellaris USB controller operates as a full-speed or low-speed function controller during point-to-point communications with USB Host, Device, or OTG functions. The controller complies with the USB 2.0 standard, which includes SUSPEND and RESUME signaling. 16 endpoints including two hard-wired for control transfers (one endpoint for IN and one endpoint for OUT) plus 14 endpoints defined by firmware along with a dynamic sizable FIFO support multiple packet queueing. µDMA access to the FIFO allows minimal interference from system software. Software-controlled connect and disconnect allows flexibility during USB device start-up. The controller complies with OTG standard's session request protocol (SRP) and host negotiation protocol (HNP). The Stellaris USB module has the following features: ■ Complies with USB-IF certification standards ■ USB 2.0 full-speed (12 Mbps) and low-speed (1.5 Mbps) operation with integrated PHY ■ 4 transfer types: Control, Interrupt, Bulk, and Isochronous ■ 16 endpoints – 1 dedicated control IN endpoint and 1 dedicated control OUT endpoint – 7 configurable IN endpoints and 7 configurable OUT endpoints ■ 4 KB dedicated endpoint memory: one endpoint may be defined for double-buffered 1023-byte isochronous packet size ■ VBUS droop and valid ID detection and interrupt ■ Efficient transfers using Micro Direct Memory Access Controller (µDMA) – Separate channels for transmit and receive for up to three IN endpoints and three OUT endpoints – Channel requests asserted when FIFO contains required amount of data 1124 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 18.1 Block Diagram Figure 18-1. USB Module Block Diagram DMA Requests Endpoint Control Transmit EP0 – 31 Control Receive CPU Interface Combine Endpoints Host Transaction Scheduler Interrupt Control Interrupts EP Reg. Decoder UTM Synchronization Packet Encode/Decode Data Sync Packet Encode USB PHY USB FS/LS PHY HNP/SRP Packet Decode Timers CRC Gen/Check FIFO RAM Controller Rx Rx Buff Buff Tx Buff Common Regs AHB bus – Slave mode Cycle Control Tx Buff Cycle Control FIFO Decoder USB Data Lines D+ and D- 18.2 Signal Description The following table lists the external signals of the USB controller and describes the function of each. Some USB controller signals are alternate functions for some GPIO signals and default to be GPIO signals at reset. The column in the table below titled "Pin Mux/Pin Assignment" lists the possible GPIO pin placements for these USB signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 698) should be set to choose the USB function. The number in parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control (GPIOPCTL) register (page 717) to assign the USB signal to the specified GPIO port pin. The USB0VBUS and USB0ID signals are configured by clearing the appropriate DEN bit in the GPIO Digital Enable (GPIODEN) register. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 674. The remaining signals (with the word "fixed" in the Pin Mux/Pin Assignment column) have a fixed pin assignment and function. Note: When used in OTG mode, USB0VBUS and USB0ID do not require any configuration as they are dedicated pins for the USB controller and directly connect to the USB connector's VBUS and ID signals. If the USB controller is used as either a dedicated Host or Device, the DEVMODOTG and DEVMOD bits in the USB General-Purpose Control and Status (USBGPCS) register can be used to connect the USB0VBUS and USB0ID inputs to fixed levels internally, freeing the PB0 and PB1 pins for GPIO use. For proper self-powered Device operation, the VBUS value must still be monitored to assure that if the Host removes VBUS, the self-powered Device disables the D+/D- pull-up resistors. This function can be accomplished by connecting a standard GPIO to VBUS. Table 18-1. USB Signals (157BGA) Pin Name USB0DM Pin Number Pin Mux / Pin Assignment E13 PL7 a Pin Type Buffer Type I/O Analog Description Bidirectional differential data pin (D- per USB specification) for USB0. November 08, 2011 1125 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Table 18-1. USB Signals (157BGA) (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description USB0DP E12 PL6 I/O Analog Bidirectional differential data pin (D+ per USB specification) for USB0. USB0EPEN K1 C2 L9 K7 PC6 (8) PD2 (8) PF4 (8) PG4 (8) O TTL Optionally used in Host mode to control an external power source to supply power to the USB bus. USB0ID F11 PB0 I Analog This signal senses the state of the USB ID signal. The USB PHY enables an integrated pull-up, and an external element (USB connector) indicates the initial state of the USB controller (pulled down is the A side of the cable and pulled up is the B side). USB0PFLT K2 C1 K9 L7 PC7 (8) PD3 (8) PF5 (8) PG5 (8) I TTL Optionally used in Host mode by an external power source to indicate an error state by that power source. USB0VBUS E11 PB1 I/O Analog This signal is used during the session request protocol. This signal allows the USB PHY to both sense the voltage level of VBUS, and pull up VBUS momentarily during VBUS pulsing. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 18.3 Functional Description The Stellaris USB controller provides full OTG negotiation by supporting both the session request protocol (SRP) and the host negotiation protocol (HNP). The session request protocol allows devices on the B side of a cable to request the A side device turn on VBUS. The host negotiation protocol is used after the initial session request protocol has powered the bus and provides a method to determine which end of the cable will act as the Host controller. When the device is connected to non-OTG peripherals or devices, the controller can detect which cable end was used and provides a register to indicate if the controller should act as the Host or the Device controller. This indication and the mode of operation are handled automatically by the USB controller. This auto-detection allows the system to use a single A/B connector instead of having both A and B connectors in the system and supports full OTG negotiations with other OTG devices. In addition, the USB controller provides support for connecting to non-OTG peripherals or Host controllers. The USB controller can be configured to act as either a dedicated Host or Device, in which case, the USB0VBUS and USB0ID signals can be used as GPIOs. However, when the USB controller is acting as a self-powered Device, a GPIO input or analog comparator input must be connected to VBUS and configured to generate an interrupt when the VBUS level drops. This interrupt is used to disable the pullup resistor on the USB0DP signal. Note: 18.3.1 When the USB module is in operation, MOSC must be the clock source, either with or without using the PLL, and the system clock must be at least 30 MHz. Operation as a Device This section describes the Stellaris USB controller's actions when it is being used as a USB Device. Before the USB controller's operating mode is changed from Device to Host or Host to Device, software must reset the USB controller by setting the USB0 bit in the Software Reset Control 2 (SRCR2) register (see page 270). IN endpoints, OUT endpoints, entry into and exit from SUSPEND mode, and recognition of Start of Frame (SOF) are all described. 1126 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller When in Device mode, IN transactions are controlled by an endpoint’s transmit interface and use the transmit endpoint registers for the given endpoint. OUT transactions are handled with an endpoint's receive interface and use the receive endpoint registers for the given endpoint. When configuring the size of the FIFOs for endpoints, take into account the maximum packet size for an endpoint. ■ Bulk. Bulk endpoints should be the size of the maximum packet (up to 64 bytes) or twice the maximum packet size if double buffering is used (described further in the following section). ■ Interrupt. Interrupt endpoints should be the size of the maximum packet (up to 64 bytes) or twice the maximum packet size if double buffering is used. ■ Isochronous. Isochronous endpoints are more flexible and can be up to 1023 bytes. ■ Control. It is also possible to specify a separate control endpoint for a USB Device. However, in most cases the USB Device should use the dedicated control endpoint on the USB controller’s endpoint 0. 18.3.1.1 Endpoints When operating as a Device, the USB controller provides two dedicated control endpoints (IN and OUT) and 14 configurable endpoints (7 IN and 7 OUT) that can be used for communications with a Host controller. The endpoint number and direction associated with an endpoint is directly related to its register designation. For example, when the Host is transmitting to endpoint 1, all configuration and data is in the endpoint 1 transmit register interface. Endpoint 0 is a dedicated control endpoint used for all control transactions to endpoint 0 during enumeration or when any other control requests are made to endpoint 0. Endpoint 0 uses the first 64 bytes of the USB controller's FIFO RAM as a shared memory for both IN and OUT transactions. The remaining 14 endpoints can be configured as control, bulk, interrupt, or isochronous endpoints. They should be treated as 7 configurable IN and 7 configurable OUT endpoints. The endpoint pairs are not required to have the same type for their IN and OUT endpoint configuration. For example, the OUT portion of an endpoint pair could be a bulk endpoint, while the IN portion of that endpoint pair could be an interrupt endpoint. The address and size of the FIFOs attached to each endpoint can be modified to fit the application's needs. 18.3.1.2 IN Transactions as a Device When operating as a USB Device, data for IN transactions is handled through the FIFOs attached to the transmit endpoints. The sizes of the FIFOs for the 7 configurable IN endpoints are determined by the USB Transmit FIFO Start Address (USBTXFIFOADD) register. The maximum size of a data packet that may be placed in a transmit endpoint’s FIFO for transmission is programmable and is determined by the value written to the USB Maximum Transmit Data Endpoint n (USBTXMAXPn) register for that endpoint. The endpoint’s FIFO can also be configured to use double-packet or single-packet buffering. When double-packet buffering is enabled, two data packets can be buffered in the FIFO, which also requires that the FIFO is at least two packets in size. When double-packet buffering is disabled, only one packet can be buffered, even if the packet size is less than half the FIFO size. Note: The maximum packet size set for any endpoint must not exceed the FIFO size. The USBTXMAXPn register should not be written to while data is in the FIFO as unexpected results may occur. November 08, 2011 1127 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Single-Packet Buffering If the size of the transmit endpoint's FIFO is less than twice the maximum packet size for this endpoint (as set in the USB Transmit Dynamic FIFO Sizing (USBTXFIFOSZ) register), only one packet can be buffered in the FIFO and single-packet buffering is required. When each packet is completely loaded into the transmit FIFO, the TXRDY bit in the USB Transmit Control and Status Endpoint n Low (USBTXCSRLn) register must be set. If the AUTOSET bit in the USB Transmit Control and Status Endpoint n High (USBTXCSRHn) register is set, the TXRDY bit is automatically set when a maximum-sized packet is loaded into the FIFO. For packet sizes less than the maximum, the TXRDY bit must be set manually. When the TXRDY bit is set, either manually or automatically, the packet is ready to be sent. When the packet has been successfully sent, both TXRDY and FIFONE are cleared, and the appropriate transmit endpoint interrupt signaled. At this point, the next packet can be loaded into the FIFO. Double-Packet Buffering If the size of the transmit endpoint's FIFO is at least twice the maximum packet size for this endpoint, two packets can be buffered in the FIFO and double-packet buffering is allowed. As each packet is loaded into the transmit FIFO, the TXRDY bit in the USBTXCSRLn register must be set. If the AUTOSET bit in the USBTXCSRHn register is set, the TXRDY bit is automatically set when a maximum-sized packet is loaded into the FIFO. For packet sizes less than the maximum, TXRDY must be set manually. When the TXRDY bit is set, either manually or automatically, the packet is ready to be sent. After the first packet is loaded, TXRDY is immediately cleared and an interrupt is generated. A second packet can now be loaded into the transmit FIFO and TXRDY set again (either manually or automatically if the packet is the maximum size). At this point, both packets are ready to be sent. After each packet has been successfully sent, TXRDY is automatically cleared and the appropriate transmit endpoint interrupt signaled to indicate that another packet can now be loaded into the transmit FIFO. The state of the FIFONE bit in the USBTXCSRLn register at this point indicates how many packets may be loaded. If the FIFONE bit is set, then another packet is in the FIFO and only one more packet can be loaded. If the FIFONE bit is clear, then no packets are in the FIFO and two more packets can be loaded. Note: 18.3.1.3 Double-packet buffering is disabled if an endpoint’s corresponding EPn bit is set in the USB Transmit Double Packet Buffer Disable (USBTXDPKTBUFDIS) register. This bit is set by default, so it must be cleared to enable double-packet buffering. OUT Transactions as a Device When in Device mode, OUT transactions are handled through the USB controller receive FIFOs. The sizes of the receive FIFOs for the 7 configurable OUT endpoints are determined by the USB Receive FIFO Start Address (USBRXFIFOADD) register. The maximum amount of data received by an endpoint in any packet is determined by the value written to the USB Maximum Receive Data Endpoint n (USBRXMAXPn) register for that endpoint. When double-packet buffering is enabled, two data packets can be buffered in the FIFO. When double-packet buffering is disabled, only one packet can be buffered even if the packet is less than half the FIFO size. Note: In all cases, the maximum packet size must not exceed the FIFO size. Single-Packet Buffering If the size of the receive endpoint FIFO is less than twice the maximum packet size for an endpoint, only one data packet can be buffered in the FIFO and single-packet buffering is required. When a packet is received and placed in the receive FIFO, the RXRDY and FULL bits in the USB Receive Control and Status Endpoint n Low (USBRXCSRLn) register are set and the appropriate receive endpoint is signaled, indicating that a packet can now be unloaded from the FIFO. After the packet 1128 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller has been unloaded, the RXRDY bit must be cleared in order to allow further packets to be received. This action also generates the acknowledge signaling to the Host controller. If the AUTOCL bit in the USB Receive Control and Status Endpoint n High (USBRXCSRHn) register is set and a maximum-sized packet is unloaded from the FIFO, the RXRDY and FULL bits are cleared automatically. For packet sizes less than the maximum, RXRDY must be cleared manually. Double-Packet Buffering If the size of the receive endpoint FIFO is at least twice the maximum packet size for the endpoint, two data packets can be buffered and double-packet buffering can be used. When the first packet is received and loaded into the receive FIFO, the RXRDY bit in the USBRXCSRLn register is set and the appropriate receive endpoint interrupt is signaled to indicate that a packet can now be unloaded from the FIFO. Note: The FULL bit in USBRXCSRLn is not set when the first packet is received. It is only set if a second packet is received and loaded into the receive FIFO. After each packet has been unloaded, the RXRDY bit must be cleared to allow further packets to be received. If the AUTOCL bit in the USBRXCSRHn register is set and a maximum-sized packet is unloaded from the FIFO, the RXRDY bit is cleared automatically. For packet sizes less than the maximum, RXRDY must be cleared manually. If the FULL bit is set when RXRDY is cleared, the USB controller first clears the FULL bit, then sets RXRDY again to indicate that there is another packet waiting in the FIFO to be unloaded. Note: 18.3.1.4 Double-packet buffering is disabled if an endpoint’s corresponding EPn bit is set in the USB Receive Double Packet Buffer Disable (USBRXDPKTBUFDIS) register. This bit is set by default, so it must be cleared to enable double-packet buffering. Scheduling The Device has no control over the scheduling of transactions as scheduling is determined by the Host controller. The Stellaris USB controller can set up a transaction at any time. The USB controller waits for the request from the Host controller and generates an interrupt when the transaction is complete or if it was terminated due to some error. If the Host controller makes a request and the Device controller is not ready, the USB controller sends a busy response (NAK) to all requests until it is ready. 18.3.1.5 Additional Actions The USB controller responds automatically to certain conditions on the USB bus or actions by the Host controller such as when the USB controller automatically stalls a control transfer or unexpected zero length OUT data packets. Stalled Control Transfer The USB controller automatically issues a STALL handshake to a control transfer under the following conditions: 1. The Host sends more data during an OUT data phase of a control transfer than was specified in the Device request during the SETUP phase. This condition is detected by the USB controller when the Host sends an OUT token (instead of an IN token) after the last OUT packet has been unloaded and the DATAEND bit in the USB Control and Status Endpoint 0 Low (USBCSRL0) register has been set. 2. The Host requests more data during an IN data phase of a control transfer than was specified in the Device request during the SETUP phase. This condition is detected by the USB controller November 08, 2011 1129 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller when the Host sends an IN token (instead of an OUT token) after the CPU has cleared TXRDY and set DATAEND in response to the ACK issued by the Host to what should have been the last packet. 3. The Host sends more than USBRXMAXPn bytes of data with an OUT data token. 4. The Host sends more than a zero length data packet for the OUT STATUS phase. Zero Length OUT Data Packets A zero-length OUT data packet is used to indicate the end of a control transfer. In normal operation, such packets should only be received after the entire length of the Device request has been transferred. However, if the Host sends a zero-length OUT data packet before the entire length of Device request has been transferred, it is signaling the premature end of the transfer. In this case, the USB controller automatically flushes any IN token ready for the data phase from the FIFO and sets the DATAEND bit in the USBCSRL0 register. Setting the Device Address When a Host is attempting to enumerate the USB Device, it requests that the Device change its address from zero to some other value. The address is changed by writing the value that the Host requested to the USB Device Functional Address (USBFADDR) register. However, care should be taken when writing to USBFADDR to avoid changing the address before the transaction is complete. This register should only be set after the SET_ADDRESS command is complete. Like all control transactions, the transaction is only complete after the Device has left the STATUS phase. In the case of a SET_ADDRESS command, the transaction is completed by responding to the IN request from the Host with a zero-byte packet. Once the Device has responded to the IN request, the USBFADDR register should be programmed to the new value as soon as possible to avoid missing any new commands sent to the new address. Note: 18.3.1.6 If the USBFADDR register is set to the new value as soon as the Device receives the OUT transaction with the SET_ADDRESS command in the packet, it changes the address during the control transfer. In this case, the Device does not receive the IN request that allows the USB transaction to exit the STATUS phase of the control transfer because it is sent to the old address. As a result, the Host does not get a response to the IN request, and the Host fails to enumerate the Device. Device Mode SUSPEND When no activity has occurred on the USB bus for 3 ms, the USB controller automatically enters SUSPEND mode. If the SUSPEND interrupt has been enabled in the USB Interrupt Enable (USBIE) register, an interrupt is generated at this time. When in SUSPEND mode, the PHY also goes into SUSPEND mode. When RESUME signaling is detected, the USB controller exits SUSPEND mode and takes the PHY out of SUSPEND. If the RESUME interrupt is enabled, an interrupt is generated. The USB controller can also be forced to exit SUSPEND mode by setting the RESUME bit in the USB Power (USBPOWER) register. When this bit is set, the USB controller exits SUSPEND mode and drives RESUME signaling onto the bus. The RESUME bit must be cleared after 10 ms (a maximum of 15 ms) to end RESUME signaling. To meet USB power requirements, the controller can be put into Deep Sleep mode which keeps the controller in a static state. The USB controller is not able to Hibernate because all the internal states are lost as a result. 1130 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 18.3.1.7 Start-of-Frame When the USB controller is operating in Device mode, it receives a Start-Of-Frame (SOF) packet from the Host once every millisecond. When the SOF packet is received, the 11-bit frame number contained in the packet is written into the USB Frame Value (USBFRAME) register, and an SOF interrupt is also signaled and can be handled by the application. Once the USB controller has started to receive SOF packets, it expects one every millisecond. If no SOF packet is received after 1.00358 ms, the packet is assumed to have been lost, and the USBFRAME register is not updated. The USB controller continues and resynchronizes these pulses to the received SOF packets when these packets are successfully received again. 18.3.1.8 USB RESET When the USB controller is in Device mode and a RESET condition is detected on the USB bus, the USB controller automatically performs the following actions: ■ Clears the USBFADDR register. ■ Clears the USB Endpoint Index (USBEPIDX) register. ■ Flushes all endpoint FIFOs. ■ Clears all control/status registers. ■ Enables all endpoint interrupts. ■ Generates a RESET interrupt. When the application software driving the USB controller receives a RESET interrupt, any open pipes are closed and the USB controller waits for bus enumeration to begin. 18.3.1.9 Connect/Disconnect The USB controller connection to the USB bus is handled by software. The USB PHY can be switched between normal mode and non-driving mode by setting or clearing the SOFTCONN bit of the USBPOWER register. When the SOFTCONN bit is set, the PHY is placed in its normal mode, and the USB0DP/USB0DM lines of the USB bus are enabled. At the same time, the USB controller is placed into a state, in which it does not respond to any USB signaling except a USB RESET. When the SOFTCONN bit is cleared, the PHY is put into non-driving mode, USB0DP and USB0DM are tristated, and the USB controller appears to other devices on the USB bus as if it has been disconnected. The non-driving mode is the default so the USB controller appears disconnected until the SOFTCONN bit has been set. The application software can then choose when to set the PHY into its normal mode. Systems with a lengthy initialization procedure may use this to ensure that initialization is complete, and the system is ready to perform enumeration before connecting to the USB bus. Once the SOFTCONN bit has been set, the USB controller can be disconnected by clearing this bit. Note: 18.3.2 The USB controller does not generate an interrupt when the Device is connected to the Host. However, an interrupt is generated when the Host terminates a session. Operation as a Host When the Stellaris USB controller is operating in Host mode, it can either be used for point-to-point communications with another USB device or, when attached to a hub, for communication with multiple devices. Before the USB controller's operating mode is changed from Host to Device or November 08, 2011 1131 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Device to Host, software must reset the USB controller by setting the USB0 bit in the Software Reset Control 2 (SRCR2) register (see page 270). Full-speed and low-speed USB devices are supported, both for point-to-point communication and for operation through a hub. The USB controller automatically carries out the necessary transaction translation needed to allow a low-speed or full-speed device to be used with a USB 2.0 hub. Control, bulk, isochronous, and interrupt transactions are supported. This section describes the USB controller's actions when it is being used as a USB Host. Configuration of IN endpoints, OUT endpoints, entry into and exit from SUSPEND mode, and RESET are all described. When in Host mode, IN transactions are controlled by an endpoint’s receive interface. All IN transactions use the receive endpoint registers and all OUT endpoints use the transmit endpoint registers for a given endpoint. As in Device mode, the FIFOs for endpoints should take into account the maximum packet size for an endpoint. ■ Bulk. Bulk endpoints should be the size of the maximum packet (up to 64 bytes) or twice the maximum packet size if double buffering is used (described further in the following section). ■ Interrupt. Interrupt endpoints should be the size of the maximum packet (up to 64 bytes) or twice the maximum packet size if double buffering is used. ■ Isochronous. Isochronous endpoints are more flexible and can be up to 1023 bytes. ■ Control. It is also possible to specify a separate control endpoint to communicate with a Device. However, in most cases the USB controller should use the dedicated control endpoint to communicate with a Device’s endpoint 0. 18.3.2.1 Endpoints The endpoint registers are used to control the USB endpoint interfaces which communicate with Device(s) that are connected. The endpoints consist of a dedicated control IN endpoint, a dedicated control OUT endpoint, 7 configurable OUT endpoints, and 7 configurable IN endpoints. The dedicated control interface can only be used for control transactions to endpoint 0 of Devices. These control transactions are used during enumeration or other control functions that communicate using endpoint 0 of Devices. This control endpoint shares the first 64 bytes of the USB controller’s FIFO RAM for IN and OUT transactions. The remaining IN and OUT interfaces can be configured to communicate with control, bulk, interrupt, or isochronous Device endpoints. These USB interfaces can be used to simultaneously schedule as many as 7 independent OUT and 7 independent IN transactions to any endpoints on any Device. The IN and OUT controls are paired in three sets of registers. However, they can be configured to communicate with different types of endpoints and different endpoints on Devices. For example, the first pair of endpoint controls can be split so that the OUT portion is communicating with a Device’s bulk OUT endpoint 1, while the IN portion is communicating with a Device’s interrupt IN endpoint 2. Before accessing any Device, whether for point-to-point communications or for communications via a hub, the relevant USB Receive Functional Address Endpoint n (USBRXFUNCADDRn) or USB Transmit Functional Address Endpoint n (USBTXFUNCADDRn) registers must be set for each receive or transmit endpoint to record the address of the Device being accessed. The USB controller also supports connections to Devices through a USB hub by providing a register that specifies the hub address and port of each USB transfer. The FIFO address and size are customizable and can be specified for each USB IN and OUT transfer. Customization includes allowing one FIFO per transaction, sharing a FIFO across transactions, and allowing for double-buffered FIFOs. 1132 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 18.3.2.2 IN Transactions as a Host IN transactions are handled in a similar manner to the way in which OUT transactions are handled when the USB controller is in Device mode except that the transaction first must be initiated by setting the REQPKT bit in the USBCSRL0 register, indicating to the transaction scheduler that there is an active transaction on this endpoint. The transaction scheduler then sends an IN token to the target Device. When the packet is received and placed in the receive FIFO, the RXRDY bit in the USBCSRL0 register is set, and the appropriate receive endpoint interrupt is signaled to indicate that a packet can now be unloaded from the FIFO. When the packet has been unloaded, RXRDY must be cleared. The AUTOCL bit in the USBRXCSRHn register can be used to have RXRDY automatically cleared when a maximum-sized packet has been unloaded from the FIFO. The AUTORQ bit in USBRXCSRHn causes the REQPKT bit to be automatically set when the RXRDY bit is cleared. The AUTOCL and AUTORQ bits can be used with µDMA accesses to perform complete bulk transfers without main processor intervention. When the RXRDY bit is cleared, the controller sends an acknowledge to the Device. When there is a known number of packets to be transferred, the USB Request Packet Count in Block Transfer Endpoint n (USBRQPKTCOUNTn) register associated with the endpoint should be configured to the number of packets to be transferred. The USB controller decrements the value in the USBRQPKTCOUNTn register following each request. When the USBRQPKTCOUNTn value decrements to 0, the AUTORQ bit is cleared to prevent any further transactions being attempted. For cases where the size of the transfer is unknown, USBRQPKTCOUNTn should be cleared. AUTORQ then remains set until cleared by the reception of a short packet (that is, less than the MAXLOAD value in the USBRXMAXPn register) such as may occur at the end of a bulk transfer. If the Device responds to a bulk or interrupt IN token with a NAK, the USB Host controller keeps retrying the transaction until any NAK Limit that has been set has been reached. If the target Device responds with a STALL, however, the USB Host controller does not retry the transaction but sets the STALLED bit in the USBCSRL0 register. If the target Device does not respond to the IN token within the required time, or the packet contained a CRC or bit-stuff error, the USB Host controller retries the transaction. If after three attempts the target Device has still not responded, the USB Host controller clears the REQPKT bit and sets the ERROR bit in the USBCSRL0 register. 18.3.2.3 OUT Transactions as a Host OUT transactions are handled in a similar manner to the way in which IN transactions are handled when the USB controller is in Device mode. The TXRDY bit in the USBTXCSRLn register must be set as each packet is loaded into the transmit FIFO. Again, setting the AUTOSET bit in the USBTXCSRHn register automatically sets TXRDY when a maximum-sized packet has been loaded into the FIFO. Furthermore, AUTOSET can be used with the µDMA controller to perform complete bulk transfers without software intervention. If the target Device responds to the OUT token with a NAK, the USB Host controller keeps retrying the transaction until the NAK Limit that has been set has been reached. However, if the target Device responds with a STALL, the USB controller does not retry the transaction but interrupts the main processor by setting the STALLED bit in the USBTXCSRLn register. If the target Device does not respond to the OUT token within the required time, or the packet contained a CRC or bit-stuff error, the USB Host controller retries the transaction. If after three attempts the target Device has still not responded, the USB controller flushes the FIFO and sets the ERROR bit in the USBTXCSRLn register. 18.3.2.4 Transaction Scheduling Scheduling of transactions is handled automatically by the USB Host controller. The Host controller allows configuration of the endpoint communication scheduling based on the type of endpoint transaction. Interrupt transactions can be scheduled to occur in the range of every frame to every November 08, 2011 1133 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller 255 frames in 1 frame increments. Bulk endpoints do not allow scheduling parameters, but do allow for a NAK timeout in the event an endpoint on a Device is not responding. Isochronous endpoints can be scheduled from every frame to every 216 frames, in powers of 2. The USB controller maintains a frame counter. If the target Device is a full-speed device, the USB controller automatically sends an SOF packet at the start of each frame and increments the frame counter. If the target Device is a low-speed device, a K state is transmitted on the bus to act as a keep-alive to stop the low-speed device from going into SUSPEND mode. After the SOF packet has been transmitted, the USB Host controller cycles through all the configured endpoints looking for active transactions. An active transaction is defined as a receive endpoint for which the REQPKT bit is set or a transmit endpoint for which the TXRDY bit and/or the FIFONE bit is set. An isochronous or interrupt transaction is started if the transaction is found on the first scheduler cycle of a frame and if the interval counter for that endpoint has counted down to zero. As a result, only one interrupt or isochronous transaction occurs per endpoint every n frames, where n is the interval set via the USB Host Transmit Interval Endpoint n (USBTXINTERVALn) or USB Host Receive Interval Endpoint n (USBRXINTERVALn) register for that endpoint. An active bulk transaction starts immediately, provided sufficient time is left in the frame to complete the transaction before the next SOF packet is due. If the transaction must be retried (for example, because a NAK was received or the target Device did not respond), then the transaction is not retried until the transaction scheduler has first checked all the other endpoints for active transactions. This process ensures that an endpoint that is sending a lot of NAKs does not block other transactions on the bus. The controller also allows the user to specify a limit to the length of time for NAKs to be received from a target Device before the endpoint times out. 18.3.2.5 USB Hubs The following setup requirements apply to the USB Host controller only if it is used with a USB hub. When a full- or low-speed Device is connected to the USB controller via a USB 2.0 hub, details of the hub address and the hub port also must be recorded in the corresponding USB Receive Hub Address Endpoint n (USBRXHUBADDRn) and USB Receive Hub Port Endpoint n (USBRXHUBPORTn) or the USB Transmit Hub Address Endpoint n (USBTXHUBADDRn) and USB Transmit Hub Port Endpoint n (USBTXHUBPORTn) registers. In addition, the speed at which the Device operates (full or low) must be recorded in the USB Type Endpoint 0 (USBTYPE0) (endpoint 0), USB Host Configure Transmit Type Endpoint n (USBTXTYPEn), or USB Host Configure Receive Type Endpoint n (USBRXTYPEn) registers for each endpoint that is accessed by the Device. For hub communications, the settings in these registers record the current allocation of the endpoints to the attached USB Devices. To maximize the number of Devices supported, the USB Host controller allows this allocation to be changed dynamically by simply updating the address and speed information recorded in these registers. Any changes in the allocation of endpoints to Device functions must be made following the completion of any on-going transactions on the endpoints affected. 18.3.2.6 Babble The USB Host controller does not start a transaction until the bus has been inactive for at least the minimum inter-packet delay. The controller also does not start a transaction unless it can be finished before the end of the frame. If the bus is still active at the end of a frame, then the USB Host controller assumes that the target Device to which it is connected has malfunctioned, and the USB controller suspends all transactions and generates a babble interrupt. 1134 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 18.3.2.7 Host SUSPEND If the SUSPEND bit in the USBPOWER register is set, the USB Host controller completes the current transaction then stops the transaction scheduler and frame counter. No further transactions are started and no SOF packets are generated. To exit SUSPEND mode, set the RESUME bit and clear the SUSPEND bit. While the RESUME bit is set, the USB Host controller generates RESUME signaling on the bus. After 20 ms, the RESUME bit must be cleared, at which point the frame counter and transaction scheduler start. The Host supports the detection of a remote wake-up. 18.3.2.8 USB RESET If the RESET bit in the USBPOWER register is set, the USB Host controller generates USB RESET signaling on the bus. The RESET bit must be set for at least 20 ms to ensure correct resetting of the target Device. After the CPU has cleared the bit, the USB Host controller starts its frame counter and transaction scheduler. 18.3.2.9 Connect/Disconnect A session is started by setting the SESSION bit in the USB Device Control (USBDEVCTL) register, enabling the USB controller to wait for a Device to be connected. When a Device is detected, a connect interrupt is generated. The speed of the Device that has been connected can be determined by reading the USBDEVCTL register where the FSDEV bit is set for a full-speed Device, and the LSDEV bit is set for a low-speed Device. The USB controller must generate a RESET to the Device, and then the USB Host controller can begin Device enumeration. If the Device is disconnected while a session is in progress, a disconnect interrupt is generated. 18.3.3 OTG Mode To conserve power, the USB On-The-Go (OTG) supplement allows VBUS to only be powered up when required and to be turned off when the bus is not in use. VBUS is always supplied by the A device on the bus. The USB OTG controller determines whether it is the A device or the B device by sampling the ID input from the PHY. This signal is pulled Low when an A-type plug is sensed (signifying that the USB OTG controller should act as the A device) but taken High when a B-type plug is sensed (signifying that the USB controller is a B device). Note that when switching between OTG A and OTG B, the USB controller retains all register contents. 18.3.3.1 Starting a Session When the USB OTG controller is ready to start a session, the SESSION bit must be set in the USBDEVCTL register. The USB OTG controller then enables ID pin sensing. The ID input is either taken Low if an A-type connection is detected or High if a B-type connection is detected. The DEV bit in the USBDEVCTL register is also set to indicate whether the USB OTG controller has adopted the role of the A device or the B device. The USB OTG controller also provides an interrupt to indicate that ID pin sensing has completed and the mode value in the USBDEVCTL register is valid. This interrupt is enabled in the USBIDVIM register, and the status is checked in the USBIDVISC register. As soon as the USB controller has detected that it is on the A side of the cable, it must enable VBUS power within 100ms or the USB controller reverts to Device mode. If the USB OTG controller is the A device, then the USB OTG controller enters Host mode (the A device is always the default Host), turns on VBUS, and waits for VBUS to go above the VBUS Valid threshold, as indicated by the VBUS bit in the USBDEVCTL register going to 0x3. The USB OTG controller then waits for a peripheral to be connected. When a peripheral is detected, a Connect interrupt is signaled and either the FSDEV or LSDEV bit in the USBDEVCTL register is set, depending whether a full-speed or a low-speed peripheral is detected. The USB controller then issues a RESET November 08, 2011 1135 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller to the connected Device. The SESSION bit in the USBDEVCTL register can be cleared to end a session. The USB OTG controller also automatically ends the session if babble is detected or if VBUS drops below session valid. Note: The USB OTG controller may not remain in Host mode when connected to high-current devices. Some devices draw enough current to momentarily drop VBUS below the VBUS-valid level causing the controller to drop out of Host mode. The only way to get back into Host mode is to allow VBUS to go below the Session End level. In this situation, the device is causing VBUS to drop repeatedly and pull VBUS back low the next time VBUS is enabled. In addition, the USB OTG controller may not remain in Host mode when a device is told that it can start using it's active configuration. At this point the device starts drawing more current and can also drop VBUS below VBUS valid. If the USB OTG controller is the B device, then the USB OTG controller requests a session using the session request protocol defined in the USB On-The-Go supplement, that is, it first discharges VBUS. Then when VBUS has gone below the Session End threshold (VBUS bit in the USBDEVCTL register goes to 0x0) and the line state has been a single-ended zero for > 2 ms, the USB OTG controller pulses the data line, then pulses VBUS. At the end of the session, the SESSION bit is cleared either by the USB OTG controller or by the application software. The USB OTG controller then causes the PHY to switch out the pull-up resistor on D+, signaling the A device to end the session. 18.3.3.2 Detecting Activity When the other device of the OTG setup wishes to start a session, it either raises VBUS above the Session Valid threshold if it is the A device, or if it is the B device, it pulses the data line then pulses VBUS. Depending on which of these actions happens, the USB controller can determine whether it is the A device or the B device in the current setup and act accordingly. If VBUS is raised above the Session Valid threshold, then the USB controller is the B device. The USB controller sets the SESSION bit in the USBDEVCTL register. When RESET signaling is detected on the bus, a RESET interrupt is signaled, which is interpreted as the start of a session. The USB controller is in Device mode as the B device is the default mode. At the end of the session, the A device turns off the power to VBUS. When VBUS drops below the Session Valid threshold, the USB controller detects this drop and clears the SESSION bit to indicate that the session has ended, causing a disconnect interrupt to be signaled. If data line and VBUS pulsing is detected, then the USB controller is the A device. The controller generates a SESSION REQUEST interrupt to indicate that the B device is requesting a session. The SESSION bit in the USBDEVCTL register must be set to start a session. 18.3.3.3 Host Negotiation When the USB controller is the A device, ID is Low, and the controller automatically enters Host mode when a session starts. When the USB controller is the B device, ID is High, and the controller automatically enters Device mode when a session starts. However, software can request that the USB controller become the Host by setting the HOSTREQ bit in the USBDEVCTL register. This bit can be set either at the same time as requesting a Session Start by setting the SESSION bit in the USBDEVCTL register or at any time after a session has started. When the USB controller next enters SUSPEND mode and if the HOSTREQ bit remains set, the controller enters Host mode and begins host negotiation (as specified in the USB On-The-Go supplement) by causing the PHY to disconnect the pull-up resistor on the D+ line, causing the A device to switch to Device mode and connect its own pull-up resistor. When the USB controller detects this, a Connect interrupt is generated and the RESET bit in the USBPOWER register is set to begin resetting the A device. The 1136 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller USB controller begins this reset sequence automatically to ensure that RESET is started as required within 1 ms of the A device connecting its pull-up resistor. The main processor should wait at least 20 ms, then clear the RESET bit and enumerate the A device. When the USB OTG controller B device has finished using the bus, the USB controller goes into SUSPEND mode by setting the SUSPEND bit in the USBPOWER register. The A device detects this and either terminates the session or reverts to Host mode. If the A device is USB OTG controller, it generates a Disconnect interrupt. 18.3.4 DMA Operation The USB peripheral provides an interface connected to the μDMA controller with separate channels for 3 transmit endpoints and 3 receive endpoints. Software selects which endpoints to service with the μDMA channels using the USB DMA Select (USBDMASEL) register. The μDMA operation of the USB is enabled through the USBTXCSRHn and USBRXCSRHn registers, for the TX and RX channels respectively. When μDMA operation is enabled, the USB asserts a μDMA request on the enabled receive or transmit channel when the associated FIFO can transfer data. When either FIFO can transfer data, the burst request for that channel is asserted. The μDMA channel must be configured to operate in Basic mode, and the size of the μDMA transfer must be restricted to whole multiples of the size of the USB FIFO. Both read and write transfers of the USB FIFOs using μDMA must be configured in this manner. For example, if the USB endpoint is configured with a FIFO size of 64 bytes, the μDMA channel can be used to transfer 64 bytes to or from the endpoint FIFO. If the number of bytes to transfer is less than 64, then a programmed I/O method must be used to copy the data to or from the FIFO. If the DMAMOD bit in the USBTXCSRHn/USBRXCSRHn register is clear, an interrupt is generated after every packet is transferred, but the μDMA continues transferring data. If the DMAMOD bit is set, an interrupt is generated only when the entire μDMA transfer is complete. The interrupt occurs on the USB interrupt vector. Therefore, if interrupts are used for USB operation and the μDMA is enabled, the USB interrupt handler must be designed to handle the μDMA completion interrupt. Care must be taken when using the μDMA to unload the receive FIFO as data is read from the receive FIFO in 4 byte chunks regardless of value of the MAXLOAD field in the USBRXCSRHn register. The RXRDY bit is cleared as follows. Table 18-2. Remainder (MAXLOAD/4) Value Description 0 MAXLOAD = 64 bytes 1 MAXLOAD = 61 bytes 2 MAXLOAD = 62 bytes 3 MAXLOAD = 63 bytes Table 18-3. Actual Bytes Read Value Description 0 MAXLOAD 1 MAXLOAD+3 2 MAXLOAD+2 3 MAXLOAD+1 November 08, 2011 1137 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Table 18-4. Packet Sizes That Clear RXRDY Value Description 0 MAXLOAD, MAXLOAD-1, MAXLOAD-2, MAXLOAD-3 1 MAXLOAD 2 MAXLOAD, MAXLOAD-1 3 MAXLOAD, MAXLOAD-1, MAXLOAD-2 To enable DMA operation for the endpoint receive channel, the DMAEN bit of the USBRXCSRHn register should be set. To enable DMA operation for the endpoint transmit channel, the DMAEN bit of the USBTXCSRHn register must be set. See “Micro Direct Memory Access (μDMA)” on page 610 for more details about programming the μDMA controller. 18.4 Initialization and Configuration To use the USB Controller, the peripheral clock must be enabled via the RCGCUSB register (see page 400). In addition, the clock to the appropriate GPIO module must be enabled via the RCGCGPIO register in the System Control module (see page 389). To find out which GPIO port to enable, refer to Table 23-4 on page 1387. Configure the PMCn fields in the GPIOPCTL register to assign the USB signals to the appropriate pins (see page 717 and Table 23-5 on page 1398). The initial configuration in all cases requires that the processor enable the USB controller and USB controller’s physical layer interface (PHY) before setting any registers. The next step is to enable the USB PLL so that the correct clocking is provided to the PHY. To ensure that voltage is not supplied to the bus incorrectly, the external power control signal, USB0EPEN, should be negated on start up by configuring the USB0EPEN and USB0PFLT pins to be controlled by the USB controller and not exhibit their default GPIO behavior. Note: 18.4.1 When used in OTG mode, USB0VBUS and USB0ID do not require any configuration as they are dedicated pins for the USB controller and directly connect to the USB connector's VBUS and ID signals. If the USB controller is used as either a dedicated Host or Device, the DEVMODOTG and DEVMOD bits in the USB General-Purpose Control and Status (USBGPCS) register can be used to connect the USB0VBUS and USB0ID inputs to fixed levels internally, freeing the PB0 and PB1 pins for GPIO use. For proper self-powered Device operation, the VBUS value must still be monitored to assure that if the Host removes VBUS, the self-powered Device disables the D+/D- pull-up resistors. This function can be accomplished by connecting a standard GPIO to VBUS. Pin Configuration When using the Device controller portion of the USB controller in a system that also provides Host functionality, the power to VBUS must be disabled to allow the external Host controller to supply power. Usually, the USB0EPEN signal is used to control the external regulator and should be negated to avoid having two devices driving the USB0VBUS power pin on the USB connector. When the USB controller is acting as a Host, it is in control of two signals that are attached to an external voltage supply that provides power to VBUS. The Host controller uses the USB0EPEN signal to enable or disable power to the USB0VBUS pin on the USB connector. An input pin, USB0PFLT, provides feedback when there has been a power fault on VBUS. The USB0PFLT signal can be configured to either automatically negate the USB0EPEN signal to disable power, and/or it can generate an interrupt to the interrupt controller to allow software to handle the power fault condition. The polarity and actions related to both USB0EPEN and USB0PFLT are fully configurable in the USB 1138 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller controller. The controller also provides interrupts on Device insertion and removal to allow the Host controller code to respond to these external events. 18.4.2 Endpoint Configuration To start communication in Host or Device mode, the endpoint registers must first be configured. In Host mode, this configuration establishes a connection between an endpoint register and an endpoint on a Device. In Device mode, an endpoint must be configured before enumerating to the Host controller. In both cases, the endpoint 0 configuration is limited because it is a fixed-function, fixed-FIFO-size endpoint. In Device and Host modes, the endpoint requires little setup but does require a software-based state machine to progress through the setup, data, and status phases of a standard control transaction. In Device mode, the configuration of the remaining endpoints is done once before enumerating and then only changed if an alternate configuration is selected by the Host controller. In Host mode, the endpoints must be configured to operate as control, bulk, interrupt or isochronous mode. Once the type of endpoint is configured, a FIFO area must be assigned to each endpoint. In the case of bulk, control and interrupt endpoints, each has a maximum of 64 bytes per transaction. Isochronous endpoints can have packets with up to 1023 bytes per packet. In either mode, the maximum packet size for the given endpoint must be set prior to sending or receiving data. Configuring each endpoint’s FIFO involves reserving a portion of the overall USB FIFO RAM to each endpoint. The total FIFO RAM available is 2 Kbytes with the first 64 bytes reserved for endpoint 0. The endpoint’s FIFO must be at least as large as the maximum packet size. The FIFO can also be configured as a double-buffered FIFO so that interrupts occur at the end of each packet and allow filling the other half of the FIFO. If operating as a Device, the USB Device controller's soft connect must be enabled when the Device is ready to start communications, indicating to the Host controller that the Device is ready to start the enumeration process. If operating as a Host controller, the Device soft connect must be disabled and power must be provided to VBUS via the USB0EPEN signal. 18.5 Register Map Table 18-5 on page 1139 lists the registers. All addresses given are relative to the USB base address of 0x4005.0000. Note that the USB controller clock must be enabled before the registers can be programmed (see page 400). There must be a delay of 3 system clocks after the USB module clock is enabled before any USB module registers are accessed. Table 18-5. Universal Serial Bus (USB) Controller Register Map Offset Name Type Reset Description See page 0x000 USBFADDR R/W 0x00 USB Device Functional Address 1146 0x001 USBPOWER R/W 0x20 USB Power 1147 0x002 USBTXIS RO 0x0000 USB Transmit Interrupt Status 1150 0x004 USBRXIS RO 0x0000 USB Receive Interrupt Status 1152 0x006 USBTXIE R/W 0xFFFF USB Transmit Interrupt Enable 1153 0x008 USBRXIE R/W 0xFFFE USB Receive Interrupt Enable 1155 0x00A USBIS RO 0x00 USB General Interrupt Status 1156 November 08, 2011 1139 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Table 18-5. Universal Serial Bus (USB) Controller Register Map (continued) Offset Name Type Reset Description See page 0x00B USBIE R/W 0x06 USB Interrupt Enable 1159 0x00C USBFRAME RO 0x0000 USB Frame Value 1162 0x00E USBEPIDX R/W 0x00 USB Endpoint Index 1163 0x00F USBTEST R/W 0x00 USB Test Mode 1164 0x020 USBFIFO0 R/W 0x0000.0000 USB FIFO Endpoint 0 1166 0x024 USBFIFO1 R/W 0x0000.0000 USB FIFO Endpoint 1 1166 0x028 USBFIFO2 R/W 0x0000.0000 USB FIFO Endpoint 2 1166 0x02C USBFIFO3 R/W 0x0000.0000 USB FIFO Endpoint 3 1166 0x030 USBFIFO4 R/W 0x0000.0000 USB FIFO Endpoint 4 1166 0x034 USBFIFO5 R/W 0x0000.0000 USB FIFO Endpoint 5 1166 0x038 USBFIFO6 R/W 0x0000.0000 USB FIFO Endpoint 6 1166 0x03C USBFIFO7 R/W 0x0000.0000 USB FIFO Endpoint 7 1166 0x060 USBDEVCTL R/W 0x80 USB Device Control 1167 0x062 USBTXFIFOSZ R/W 0x00 USB Transmit Dynamic FIFO Sizing 1169 0x063 USBRXFIFOSZ R/W 0x00 USB Receive Dynamic FIFO Sizing 1169 0x064 USBTXFIFOADD R/W 0x0000 USB Transmit FIFO Start Address 1170 0x066 USBRXFIFOADD R/W 0x0000 USB Receive FIFO Start Address 1170 0x07A USBCONTIM R/W 0x5C USB Connect Timing 1171 0x07B USBVPLEN R/W 0x3C USB OTG VBUS Pulse Timing 1172 0x07D USBFSEOF R/W 0x77 USB Full-Speed Last Transaction to End of Frame Timing 1173 0x07E USBLSEOF R/W 0x72 USB Low-Speed Last Transaction to End of Frame Timing 1174 0x080 USBTXFUNCADDR0 R/W 0x00 USB Transmit Functional Address Endpoint 0 1175 0x082 USBTXHUBADDR0 R/W 0x00 USB Transmit Hub Address Endpoint 0 1176 0x083 USBTXHUBPORT0 R/W 0x00 USB Transmit Hub Port Endpoint 0 1177 0x088 USBTXFUNCADDR1 R/W 0x00 USB Transmit Functional Address Endpoint 1 1175 0x08A USBTXHUBADDR1 R/W 0x00 USB Transmit Hub Address Endpoint 1 1176 0x08B USBTXHUBPORT1 R/W 0x00 USB Transmit Hub Port Endpoint 1 1177 0x08C USBRXFUNCADDR1 R/W 0x00 USB Receive Functional Address Endpoint 1 1178 0x08E USBRXHUBADDR1 R/W 0x00 USB Receive Hub Address Endpoint 1 1179 0x08F USBRXHUBPORT1 R/W 0x00 USB Receive Hub Port Endpoint 1 1180 0x090 USBTXFUNCADDR2 R/W 0x00 USB Transmit Functional Address Endpoint 2 1175 1140 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 18-5. Universal Serial Bus (USB) Controller Register Map (continued) Offset Name Type Reset Description See page 0x092 USBTXHUBADDR2 R/W 0x00 USB Transmit Hub Address Endpoint 2 1176 0x093 USBTXHUBPORT2 R/W 0x00 USB Transmit Hub Port Endpoint 2 1177 0x094 USBRXFUNCADDR2 R/W 0x00 USB Receive Functional Address Endpoint 2 1178 0x096 USBRXHUBADDR2 R/W 0x00 USB Receive Hub Address Endpoint 2 1179 0x097 USBRXHUBPORT2 R/W 0x00 USB Receive Hub Port Endpoint 2 1180 0x098 USBTXFUNCADDR3 R/W 0x00 USB Transmit Functional Address Endpoint 3 1175 0x09A USBTXHUBADDR3 R/W 0x00 USB Transmit Hub Address Endpoint 3 1176 0x09B USBTXHUBPORT3 R/W 0x00 USB Transmit Hub Port Endpoint 3 1177 0x09C USBRXFUNCADDR3 R/W 0x00 USB Receive Functional Address Endpoint 3 1178 0x09E USBRXHUBADDR3 R/W 0x00 USB Receive Hub Address Endpoint 3 1179 0x09F USBRXHUBPORT3 R/W 0x00 USB Receive Hub Port Endpoint 3 1180 0x0A0 USBTXFUNCADDR4 R/W 0x00 USB Transmit Functional Address Endpoint 4 1175 0x0A2 USBTXHUBADDR4 R/W 0x00 USB Transmit Hub Address Endpoint 4 1176 0x0A3 USBTXHUBPORT4 R/W 0x00 USB Transmit Hub Port Endpoint 4 1177 0x0A4 USBRXFUNCADDR4 R/W 0x00 USB Receive Functional Address Endpoint 4 1178 0x0A6 USBRXHUBADDR4 R/W 0x00 USB Receive Hub Address Endpoint 4 1179 0x0A7 USBRXHUBPORT4 R/W 0x00 USB Receive Hub Port Endpoint 4 1180 0x0A8 USBTXFUNCADDR5 R/W 0x00 USB Transmit Functional Address Endpoint 5 1175 0x0AA USBTXHUBADDR5 R/W 0x00 USB Transmit Hub Address Endpoint 5 1176 0x0AB USBTXHUBPORT5 R/W 0x00 USB Transmit Hub Port Endpoint 5 1177 0x0AC USBRXFUNCADDR5 R/W 0x00 USB Receive Functional Address Endpoint 5 1178 0x0AE USBRXHUBADDR5 R/W 0x00 USB Receive Hub Address Endpoint 5 1179 0x0AF USBRXHUBPORT5 R/W 0x00 USB Receive Hub Port Endpoint 5 1180 0x0B0 USBTXFUNCADDR6 R/W 0x00 USB Transmit Functional Address Endpoint 6 1175 0x0B2 USBTXHUBADDR6 R/W 0x00 USB Transmit Hub Address Endpoint 6 1176 0x0B3 USBTXHUBPORT6 R/W 0x00 USB Transmit Hub Port Endpoint 6 1177 0x0B4 USBRXFUNCADDR6 R/W 0x00 USB Receive Functional Address Endpoint 6 1178 0x0B6 USBRXHUBADDR6 R/W 0x00 USB Receive Hub Address Endpoint 6 1179 0x0B7 USBRXHUBPORT6 R/W 0x00 USB Receive Hub Port Endpoint 6 1180 0x0B8 USBTXFUNCADDR7 R/W 0x00 USB Transmit Functional Address Endpoint 7 1175 0x0BA USBTXHUBADDR7 R/W 0x00 USB Transmit Hub Address Endpoint 7 1176 0x0BB USBTXHUBPORT7 R/W 0x00 USB Transmit Hub Port Endpoint 7 1177 November 08, 2011 1141 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Table 18-5. Universal Serial Bus (USB) Controller Register Map (continued) Offset Name Type Reset Description See page 0x0BC USBRXFUNCADDR7 R/W 0x00 USB Receive Functional Address Endpoint 7 1178 0x0BE USBRXHUBADDR7 R/W 0x00 USB Receive Hub Address Endpoint 7 1179 0x0BF USBRXHUBPORT7 R/W 0x00 USB Receive Hub Port Endpoint 7 1180 0x102 USBCSRL0 W1C 0x00 USB Control and Status Endpoint 0 Low 1182 0x103 USBCSRH0 W1C 0x00 USB Control and Status Endpoint 0 High 1186 0x108 USBCOUNT0 RO 0x00 USB Receive Byte Count Endpoint 0 1188 0x10A USBTYPE0 R/W 0x00 USB Type Endpoint 0 1189 0x10B USBNAKLMT R/W 0x00 USB NAK Limit 1190 0x110 USBTXMAXP1 R/W 0x0000 USB Maximum Transmit Data Endpoint 1 1181 0x112 USBTXCSRL1 R/W 0x00 USB Transmit Control and Status Endpoint 1 Low 1191 0x113 USBTXCSRH1 R/W 0x00 USB Transmit Control and Status Endpoint 1 High 1195 0x114 USBRXMAXP1 R/W 0x0000 USB Maximum Receive Data Endpoint 1 1199 0x116 USBRXCSRL1 R/W 0x00 USB Receive Control and Status Endpoint 1 Low 1200 0x117 USBRXCSRH1 R/W 0x00 USB Receive Control and Status Endpoint 1 High 1205 0x118 USBRXCOUNT1 RO 0x0000 USB Receive Byte Count Endpoint 1 1209 0x11A USBTXTYPE1 R/W 0x00 USB Host Transmit Configure Type Endpoint 1 1210 0x11B USBTXINTERVAL1 R/W 0x00 USB Host Transmit Interval Endpoint 1 1212 0x11C USBRXTYPE1 R/W 0x00 USB Host Configure Receive Type Endpoint 1 1213 0x11D USBRXINTERVAL1 R/W 0x00 USB Host Receive Polling Interval Endpoint 1 1215 0x120 USBTXMAXP2 R/W 0x0000 USB Maximum Transmit Data Endpoint 2 1181 0x122 USBTXCSRL2 R/W 0x00 USB Transmit Control and Status Endpoint 2 Low 1191 0x123 USBTXCSRH2 R/W 0x00 USB Transmit Control and Status Endpoint 2 High 1195 0x124 USBRXMAXP2 R/W 0x0000 USB Maximum Receive Data Endpoint 2 1199 0x126 USBRXCSRL2 R/W 0x00 USB Receive Control and Status Endpoint 2 Low 1200 0x127 USBRXCSRH2 R/W 0x00 USB Receive Control and Status Endpoint 2 High 1205 0x128 USBRXCOUNT2 RO 0x0000 USB Receive Byte Count Endpoint 2 1209 0x12A USBTXTYPE2 R/W 0x00 USB Host Transmit Configure Type Endpoint 2 1210 0x12B USBTXINTERVAL2 R/W 0x00 USB Host Transmit Interval Endpoint 2 1212 0x12C USBRXTYPE2 R/W 0x00 USB Host Configure Receive Type Endpoint 2 1213 0x12D USBRXINTERVAL2 R/W 0x00 USB Host Receive Polling Interval Endpoint 2 1215 0x130 USBTXMAXP3 R/W 0x0000 USB Maximum Transmit Data Endpoint 3 1181 0x132 USBTXCSRL3 R/W 0x00 USB Transmit Control and Status Endpoint 3 Low 1191 1142 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 18-5. Universal Serial Bus (USB) Controller Register Map (continued) Offset Name Type Reset Description See page 0x133 USBTXCSRH3 R/W 0x00 USB Transmit Control and Status Endpoint 3 High 1195 0x134 USBRXMAXP3 R/W 0x0000 USB Maximum Receive Data Endpoint 3 1199 0x136 USBRXCSRL3 R/W 0x00 USB Receive Control and Status Endpoint 3 Low 1200 0x137 USBRXCSRH3 R/W 0x00 USB Receive Control and Status Endpoint 3 High 1205 0x138 USBRXCOUNT3 RO 0x0000 USB Receive Byte Count Endpoint 3 1209 0x13A USBTXTYPE3 R/W 0x00 USB Host Transmit Configure Type Endpoint 3 1210 0x13B USBTXINTERVAL3 R/W 0x00 USB Host Transmit Interval Endpoint 3 1212 0x13C USBRXTYPE3 R/W 0x00 USB Host Configure Receive Type Endpoint 3 1213 0x13D USBRXINTERVAL3 R/W 0x00 USB Host Receive Polling Interval Endpoint 3 1215 0x140 USBTXMAXP4 R/W 0x0000 USB Maximum Transmit Data Endpoint 4 1181 0x142 USBTXCSRL4 R/W 0x00 USB Transmit Control and Status Endpoint 4 Low 1191 0x143 USBTXCSRH4 R/W 0x00 USB Transmit Control and Status Endpoint 4 High 1195 0x144 USBRXMAXP4 R/W 0x0000 USB Maximum Receive Data Endpoint 4 1199 0x146 USBRXCSRL4 R/W 0x00 USB Receive Control and Status Endpoint 4 Low 1200 0x147 USBRXCSRH4 R/W 0x00 USB Receive Control and Status Endpoint 4 High 1205 0x148 USBRXCOUNT4 RO 0x0000 USB Receive Byte Count Endpoint 4 1209 0x14A USBTXTYPE4 R/W 0x00 USB Host Transmit Configure Type Endpoint 4 1210 0x14B USBTXINTERVAL4 R/W 0x00 USB Host Transmit Interval Endpoint 4 1212 0x14C USBRXTYPE4 R/W 0x00 USB Host Configure Receive Type Endpoint 4 1213 0x14D USBRXINTERVAL4 R/W 0x00 USB Host Receive Polling Interval Endpoint 4 1215 0x150 USBTXMAXP5 R/W 0x0000 USB Maximum Transmit Data Endpoint 5 1181 0x152 USBTXCSRL5 R/W 0x00 USB Transmit Control and Status Endpoint 5 Low 1191 0x153 USBTXCSRH5 R/W 0x00 USB Transmit Control and Status Endpoint 5 High 1195 0x154 USBRXMAXP5 R/W 0x0000 USB Maximum Receive Data Endpoint 5 1199 0x156 USBRXCSRL5 R/W 0x00 USB Receive Control and Status Endpoint 5 Low 1200 0x157 USBRXCSRH5 R/W 0x00 USB Receive Control and Status Endpoint 5 High 1205 0x158 USBRXCOUNT5 RO 0x0000 USB Receive Byte Count Endpoint 5 1209 0x15A USBTXTYPE5 R/W 0x00 USB Host Transmit Configure Type Endpoint 5 1210 0x15B USBTXINTERVAL5 R/W 0x00 USB Host Transmit Interval Endpoint 5 1212 0x15C USBRXTYPE5 R/W 0x00 USB Host Configure Receive Type Endpoint 5 1213 0x15D USBRXINTERVAL5 R/W 0x00 USB Host Receive Polling Interval Endpoint 5 1215 0x160 USBTXMAXP6 R/W 0x0000 USB Maximum Transmit Data Endpoint 6 1181 November 08, 2011 1143 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Table 18-5. Universal Serial Bus (USB) Controller Register Map (continued) Offset Name Type Reset Description See page 0x162 USBTXCSRL6 R/W 0x00 USB Transmit Control and Status Endpoint 6 Low 1191 0x163 USBTXCSRH6 R/W 0x00 USB Transmit Control and Status Endpoint 6 High 1195 0x164 USBRXMAXP6 R/W 0x0000 USB Maximum Receive Data Endpoint 6 1199 0x166 USBRXCSRL6 R/W 0x00 USB Receive Control and Status Endpoint 6 Low 1200 0x167 USBRXCSRH6 R/W 0x00 USB Receive Control and Status Endpoint 6 High 1205 0x168 USBRXCOUNT6 RO 0x0000 USB Receive Byte Count Endpoint 6 1209 0x16A USBTXTYPE6 R/W 0x00 USB Host Transmit Configure Type Endpoint 6 1210 0x16B USBTXINTERVAL6 R/W 0x00 USB Host Transmit Interval Endpoint 6 1212 0x16C USBRXTYPE6 R/W 0x00 USB Host Configure Receive Type Endpoint 6 1213 0x16D USBRXINTERVAL6 R/W 0x00 USB Host Receive Polling Interval Endpoint 6 1215 0x170 USBTXMAXP7 R/W 0x0000 USB Maximum Transmit Data Endpoint 7 1181 0x172 USBTXCSRL7 R/W 0x00 USB Transmit Control and Status Endpoint 7 Low 1191 0x173 USBTXCSRH7 R/W 0x00 USB Transmit Control and Status Endpoint 7 High 1195 0x174 USBRXMAXP7 R/W 0x0000 USB Maximum Receive Data Endpoint 7 1199 0x176 USBRXCSRL7 R/W 0x00 USB Receive Control and Status Endpoint 7 Low 1200 0x177 USBRXCSRH7 R/W 0x00 USB Receive Control and Status Endpoint 7 High 1205 0x178 USBRXCOUNT7 RO 0x0000 USB Receive Byte Count Endpoint 7 1209 0x17A USBTXTYPE7 R/W 0x00 USB Host Transmit Configure Type Endpoint 7 1210 0x17B USBTXINTERVAL7 R/W 0x00 USB Host Transmit Interval Endpoint 7 1212 0x17C USBRXTYPE7 R/W 0x00 USB Host Configure Receive Type Endpoint 7 1213 0x17D USBRXINTERVAL7 R/W 0x00 USB Host Receive Polling Interval Endpoint 7 1215 0x304 USBRQPKTCOUNT1 R/W 0x0000 USB Request Packet Count in Block Transfer Endpoint 1 1216 0x308 USBRQPKTCOUNT2 R/W 0x0000 USB Request Packet Count in Block Transfer Endpoint 2 1216 0x30C USBRQPKTCOUNT3 R/W 0x0000 USB Request Packet Count in Block Transfer Endpoint 3 1216 0x310 USBRQPKTCOUNT4 R/W 0x0000 USB Request Packet Count in Block Transfer Endpoint 4 1216 0x314 USBRQPKTCOUNT5 R/W 0x0000 USB Request Packet Count in Block Transfer Endpoint 5 1216 0x318 USBRQPKTCOUNT6 R/W 0x0000 USB Request Packet Count in Block Transfer Endpoint 6 1216 0x31C USBRQPKTCOUNT7 R/W 0x0000 USB Request Packet Count in Block Transfer Endpoint 7 1216 1144 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 18-5. Universal Serial Bus (USB) Controller Register Map (continued) Offset Name Type Reset Description See page 0x340 USBRXDPKTBUFDIS R/W 0x0000 USB Receive Double Packet Buffer Disable 1217 0x342 USBTXDPKTBUFDIS R/W 0x0000 USB Transmit Double Packet Buffer Disable 1218 0x400 USBEPC R/W 0x0000.0000 USB External Power Control 1219 0x404 USBEPCRIS RO 0x0000.0000 USB External Power Control Raw Interrupt Status 1222 0x408 USBEPCIM R/W 0x0000.0000 USB External Power Control Interrupt Mask 1223 0x40C USBEPCISC R/W 0x0000.0000 USB External Power Control Interrupt Status and Clear 1224 0x410 USBDRRIS RO 0x0000.0000 USB Device RESUME Raw Interrupt Status 1225 0x414 USBDRIM R/W 0x0000.0000 USB Device RESUME Interrupt Mask 1226 0x418 USBDRISC W1C 0x0000.0000 USB Device RESUME Interrupt Status and Clear 1227 0x41C USBGPCS R/W 0x0000.0003 USB General-Purpose Control and Status 1228 0x430 USBVDC R/W 0x0000.0000 USB VBUS Droop Control 1229 0x434 USBVDCRIS RO 0x0000.0000 USB VBUS Droop Control Raw Interrupt Status 1230 0x438 USBVDCIM R/W 0x0000.0000 USB VBUS Droop Control Interrupt Mask 1231 0x43C USBVDCISC R/W 0x0000.0000 USB VBUS Droop Control Interrupt Status and Clear 1232 0x444 USBIDVRIS RO 0x0000.0000 USB ID Valid Detect Raw Interrupt Status 1233 0x448 USBIDVIM R/W 0x0000.0000 USB ID Valid Detect Interrupt Mask 1234 0x44C USBIDVISC R/W1C 0x0000.0000 USB ID Valid Detect Interrupt Status and Clear 1235 0x450 USBDMASEL R/W 0x0033.2211 USB DMA Select 1236 0xFC0 USBPP RO 0x0000.08D0 USB Peripheral Properties 1238 18.6 Register Descriptions The LM4F232H5BB USB controller has On-The-Go (OTG) capabilities as specified in the USB0 bit field in the DC6 register (see page 257). OTG B / Device OTG A / Host OTG This icon indicates that the register is used in OTG B or Device mode. Some registers are used for both Host and Device mode and may have different bit definitions depending on the mode. This icon indicates that the register is used in OTG A or Host mode. Some registers are used for both Host and Device mode and may have different bit definitions depending on the mode. The USB controller is in OTG B or Device mode upon reset, so the reset values shown for these registers apply to the Device mode definition. This icon indicates that the register is used for OTG-specific functions such as ID detection and negotiation. Once OTG negotiation is complete, then the USB controller registers are used according to their Host or Device mode meanings depending on whether the OTG negotiations made the USB controller OTG A (Host) or OTG B (Device). November 08, 2011 1145 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 1: USB Device Functional Address (USBFADDR), offset 0x000 OTG B / Device USBFADDR is an 8-bit register that contains the 7-bit address of the Device part of the transaction. When the USB controller is being used in Device mode (the HOST bit in the USBDEVCTL register is clear), this register must be written with the address received through a SET_ADDRESS command, which is then used for decoding the function address in subsequent token packets. Important: See the section called “Setting the Device Address” on page 1130 for special considerations when writing this register. USB Device Functional Address (USBFADDR) Base 0x4005.0000 Offset 0x000 Type R/W, reset 0x00 7 6 5 4 Type Reset RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 FUNCADDR reserved R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 7 reserved RO 0 6:0 FUNCADDR R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Function Address Function Address of Device as received through SET_ADDRESS. 1146 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 2: USB Power (USBPOWER), offset 0x001 OTG A / USBPOWER is an 8-bit register used for controlling SUSPEND and RESUME signaling and some basic operational aspects of the USB controller. Host OTG B / Device OTG A / Host Mode USB Power (USBPOWER) Base 0x4005.0000 Offset 0x001 Type R/W, reset 0x20 7 6 5 4 reserved Type Reset RO 0 RO 0 3 2 RESET RO 1 RO 0 1 0 RESUME SUSPEND PWRDNPHY R/W 0 R/W 0 R/W1S 0 Bit/Field Name Type Reset 7:4 reserved RO 0x2 3 RESET R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. RESET Signaling Value Description 2 RESUME R/W 0 1 Enables RESET signaling on the bus. 0 Ends RESET signaling on the bus. RESUME Signaling Value Description 1 Enables RESUME signaling when the Device is in SUSPEND mode. 0 Ends RESUME signaling on the bus. This bit must be cleared by software 20 ms after being set. 1 SUSPEND R/W1S 0 SUSPEND Mode Value Description 1 Enables SUSPEND mode. 0 No effect. November 08, 2011 1147 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 0 PWRDNPHY R/W 0 Description Power Down PHY Value Description 1 Powers down the internal USB PHY. 0 No effect. OTG B / Device Mode USB Power (USBPOWER) Base 0x4005.0000 Offset 0x001 Type R/W, reset 0x20 Type Reset 7 6 ISOUP SOFTCONN R/W 0 R/W 0 5 4 reserved RO 1 RO 0 3 2 RESET 1 0 RESUME SUSPEND PWRDNPHY RO 0 R/W 0 RO 0 Bit/Field Name Type Reset 7 ISOUP R/W 0 R/W 0 Description Isochronous Update Value Description 1 The USB controller waits for an SOF token from the time the TXRDY bit is set in the USBTXCSRLn register before sending the packet. If an IN token is received before an SOF token, then a zero-length data packet is sent. 0 No effect. Note: 6 SOFTCONN R/W 0 This bit is only valid for isochronous transfers. Soft Connect/Disconnect Value Description 5:4 reserved RO 0x2 3 RESET RO 0 1 The USB D+/D- lines are enabled. 0 The USB D+/D- lines are tri-stated. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. RESET Signaling Value Description 1 RESET signaling is present on the bus. 0 RESET signaling is not present on the bus. 1148 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 2 RESUME R/W 0 Description RESUME Signaling Value Description 1 Enables RESUME signaling when the Device is in SUSPEND mode. 0 Ends RESUME signaling on the bus. This bit must be cleared by software 10 ms (a maximum of 15 ms) after being set. 1 SUSPEND RO 0 SUSPEND Mode Value Description 0 PWRDNPHY R/W 0 1 The USB controller is in SUSPEND mode. 0 This bit is cleared when software reads the interrupt register or sets the RESUME bit above. Power Down PHY Value Description 1 Powers down the internal USB PHY. 0 No effect. November 08, 2011 1149 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 3: USB Transmit Interrupt Status (USBTXIS), offset 0x002 Important: This register is read-sensitive. See the register description for details. OTG B / USBTXIS is a 16-bit read-only register that indicates which interrupts are currently active for endpoint 0 and the transmit endpoints 1–7. The meaning of the EPn bits in this register is based on the mode of the device. The EP1 through EP7 bits always indicate that the USB controller is sending data; however, in Host mode, the bits refer to OUT endpoints; while in Device mode, the bits refer to IN endpoints. The EP0 bit is special in Host and Device modes and indicates that either a control IN or control OUT endpoint has generated an interrupt. Device Note: OTG A / Host Bits relating to endpoints that have not been configured always return 0. Note also that all active interrupts are cleared when this register is read. USB Transmit Interrupt Status (USBTXIS) Base 0x4005.0000 Offset 0x002 Type RO, reset 0x0000 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 15:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 EP7 RO 0 TX Endpoint 7 Interrupt Value Description 6 EP6 RO 0 0 No interrupt. 1 The Endpoint 7 transmit interrupt is asserted. TX Endpoint 6 Interrupt Same description as EP7. 5 EP5 RO 0 TX Endpoint 5 Interrupt Same description as EP7. 4 EP4 RO 0 TX Endpoint 4 Interrupt Same description as EP7. 3 EP3 RO 0 TX Endpoint 3 Interrupt Same description as EP7. 2 EP2 RO 0 TX Endpoint 2 Interrupt Same description as EP7. 1 EP1 RO 0 TX Endpoint 1 Interrupt Same description as EP7. 1150 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 0 EP0 RO 0 Description TX and RX Endpoint 0 Interrupt Value Description 0 No interrupt. 1 The Endpoint 0 transmit and receive interrupt is asserted. November 08, 2011 1151 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 4: USB Receive Interrupt Status (USBRXIS), offset 0x004 Important: This register is read-sensitive. See the register description for details. OTG A / USBRXIS is a 16-bit read-only register that indicates which of the interrupts for receive endpoints 1–7 are currently active. Host Note: OTG B / Device 15 Bits relating to endpoints that have not been configured always return 0. Note also that all active interrupts are cleared when this register is read. USB Receive Interrupt Status (USBRXIS) Base 0x4005.0000 Offset 0x004 Type RO, reset 0x0000 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 reserved RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 15:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 EP7 RO 0 RX Endpoint 7 Interrupt Value Description 6 EP6 RO 0 0 No interrupt. 1 The Endpoint 7 transmit interrupt is asserted. RX Endpoint 6 Interrupt Same description as EP7. 5 EP5 RO 0 RX Endpoint 5 Interrupt Same description as EP7. 4 EP4 RO 0 RX Endpoint 4 Interrupt Same description as EP7. 3 EP3 RO 0 RX Endpoint 3 Interrupt Same description as EP7. 2 EP2 RO 0 RX Endpoint 2 Interrupt Same description as EP7. 1 EP1 RO 0 RX Endpoint 1 Interrupt Same description as EP7. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1152 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 5: USB Transmit Interrupt Enable (USBTXIE), offset 0x006 OTG A / Host USBTXIE is a 16-bit register that provides interrupt enable bits for the interrupts in the USBTXIS register. When a bit is set, the USB interrupt is asserted to the interrupt controller when the corresponding interrupt bit in the USBTXIS register is set. When a bit is cleared, the interrupt in the USBTXIS register is still set but the USB interrupt to the interrupt controller is not asserted. On reset, all interrupts are enabled. OTG B / Device USB Transmit Interrupt Enable (USBTXIE) Base 0x4005.0000 Offset 0x006 Type R/W, reset 0xFFFF 15 14 13 12 RO 0 RO 0 RO 0 RO 0 11 10 9 8 7 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 RO 0 RO 0 RO 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset RO 0 6 5 4 3 2 1 0 Bit/Field Name Type Reset Description 15:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 EP7 R/W 1 TX Endpoint 7 Interrupt Enable Value Description 6 EP6 R/W 1 1 An interrupt is sent to the interrupt controller when the EP7 bit in the USBTXIS register is set. 0 The EP7 transmit interrupt is suppressed and not sent to the interrupt controller. TX Endpoint 6 Interrupt Enable Same description as EP7. 5 EP5 R/W 1 TX Endpoint 5 Interrupt Enable Same description as EP7. 4 EP4 R/W 1 TX Endpoint 4 Interrupt Enable Same description as EP7. 3 EP3 R/W 1 TX Endpoint 3 Interrupt Enable Same description as EP7. 2 EP2 R/W 1 TX Endpoint 2 Interrupt Enable Same description as EP7. 1 EP1 R/W 1 TX Endpoint 1 Interrupt Enable Same description as EP7. November 08, 2011 1153 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 0 EP0 R/W 1 Description TX and RX Endpoint 0 Interrupt Enable Value Description 1 An interrupt is sent to the interrupt controller when the EP0 bit in the USBTXIS register is set. 0 The EP0 transmit and receive interrupt is suppressed and not sent to the interrupt controller. 1154 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 6: USB Receive Interrupt Enable (USBRXIE), offset 0x008 OTG A / Host USBRXIE is a 16-bit register that provides interrupt enable bits for the interrupts in the USBRXIS register. When a bit is set, the USB interrupt is asserted to the interrupt controller when the corresponding interrupt bit in the USBRXIS register is set. When a bit is cleared, the interrupt in the USBRXIS register is still set but the USB interrupt to the interrupt controller is not asserted. On reset, all interrupts are enabled. OTG B / Device USB Receive Interrupt Enable (USBRXIE) Base 0x4005.0000 Offset 0x008 Type R/W, reset 0xFFFE 15 14 13 12 RO 0 RO 0 RO 0 RO 0 11 10 9 8 7 EP7 EP6 EP5 EP4 EP3 RO 0 RO 0 RO 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset RO 0 6 5 4 3 2 1 0 EP2 EP1 reserved R/W 1 R/W 1 RO 0 Bit/Field Name Type Reset Description 15:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 EP7 R/W 1 RX Endpoint 7 Interrupt Enable Value Description 6 EP6 R/W 1 1 An interrupt is sent to the interrupt controller when the EP7 bit in the USBRXIS register is set. 0 The EP7 receive interrupt is suppressed and not sent to the interrupt controller. RX Endpoint 6 Interrupt Enable Same description as EP7. 5 EP5 R/W 1 RX Endpoint 5 Interrupt Enable Same description as EP7. 4 EP4 R/W 1 RX Endpoint 4 Interrupt Enable Same description as EP7. 3 EP3 R/W 1 RX Endpoint 3 Interrupt Enable Same description as EP7. 2 EP2 R/W 1 RX Endpoint 2 Interrupt Enable Same description as EP7. 1 EP1 R/W 1 RX Endpoint 1 Interrupt Enable Same description as EP7. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1155 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 7: USB General Interrupt Status (USBIS), offset 0x00A Important: This register is read-sensitive. See the register description for details. OTG A / USBIS is an 8-bit read-only register that indicates which USB interrupts are currently active. All active interrupts are cleared when this register is read. Host OTG B / Device OTG A / Host Mode USB General Interrupt Status (USBIS) Base 0x4005.0000 Offset 0x00A Type RO, reset 0x00 7 6 5 VBUSERR SESREQ DISCON Type Reset RO 0 RO 0 4 3 CONN SOF RO 0 RO 0 RO 0 2 1 BABBLE RESUME RO 0 RO 0 0 reserved RO 0 Bit/Field Name Type Reset Description 7 VBUSERR RO 0 VBUS Error Value Description 6 SESREQ RO 0 1 VBUS has dropped below the VBUS Valid threshold during a session. 0 No interrupt. SESSION REQUEST Value Description 5 DISCON RO 0 1 SESSION REQUEST signaling has been detected. 0 No interrupt. Session Disconnect Value Description 4 CONN RO 0 1 A Device disconnect has been detected. 0 No interrupt. Session Connect Value Description 1 A Device connection has been detected. 0 No interrupt. 1156 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 3 SOF RO 0 Description Start of Frame Value Description 2 BABBLE RO 0 1 A new frame has started. 0 No interrupt. Babble Detected Value Description 1 RESUME RO 0 1 Babble has been detected. This interrupt is active only after the first SOF has been sent. 0 No interrupt. RESUME Signaling Detected Value Description 1 RESUME signaling has been detected on the bus while the USB controller is in SUSPEND mode. 0 No interrupt. This interrupt can only be used if the USB controller's system clock is enabled. If the user disables the clock programming, the USBDRRIS, USBDRIM, and USBDRISC registers should be used. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 0 OTG B / Device Mode USB General Interrupt Status (USBIS) Base 0x4005.0000 Offset 0x00A Type RO, reset 0x00 7 6 reserved Type Reset RO 0 5 4 3 2 DISCON reserved SOF RESET RO 0 RO 0 RO 0 RO 0 RO 0 RESUME SUSPEND RO 0 Bit/Field Name Type Reset 7:6 reserved RO 0x0 5 DISCON RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Session Disconnect Value Description 1 The device has been disconnected from the host. 0 No interrupt. November 08, 2011 1157 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset Description 4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 SOF RO 0 Start of Frame Value Description 2 RESET RO 0 1 A new frame has started. 0 No interrupt. RESET Signaling Detected Value Description 1 RESUME RO 0 1 RESET signaling has been detected on the bus. 0 No interrupt. RESUME Signaling Detected Value Description 1 RESUME signaling has been detected on the bus while the USB controller is in SUSPEND mode. 0 No interrupt. This interrupt can only be used if the USB controller's system clock is enabled. If the user disables the clock programming, the USBDRRIS, USBDRIM, and USBDRISC registers should be used. 0 SUSPEND RO 0 SUSPEND Signaling Detected Value Description 1 SUSPEND signaling has been detected on the bus. 0 No interrupt. 1158 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 8: USB Interrupt Enable (USBIE), offset 0x00B OTG A / USBIE is an 8-bit register that provides interrupt enable bits for each of the interrupts in USBIS. At reset interrupts 1 and 2 are enabled in Device mode. Host OTG B / Device OTG A / Host Mode USB Interrupt Enable (USBIE) Base 0x4005.0000 Offset 0x00B Type R/W, reset 0x06 7 6 5 VBUSERR SESREQ DISCON Type Reset R/W 0 R/W 0 4 3 CONN SOF R/W 0 R/W 0 R/W 0 2 1 BABBLE RESUME R/W 1 R/W 1 Bit/Field Name Type Reset 7 VBUSERR R/W 0 0 reserved RO 0 Description Enable VBUS Error Interrupt Value Description 6 SESREQ R/W 0 1 An interrupt is sent to the interrupt controller when the VBUSERR bit in the USBIS register is set. 0 The VBUSERR interrupt is suppressed and not sent to the interrupt controller. Enable Session Request Value Description 5 DISCON R/W 0 1 An interrupt is sent to the interrupt controller when the SESREEQ bit in the USBIS register is set. 0 The SESREQ interrupt is suppressed and not sent to the interrupt controller. Enable Disconnect Interrupt Value Description 1 An interrupt is sent to the interrupt controller when the DISCON bit in the USBIS register is set. 0 The DISCON interrupt is suppressed and not sent to the interrupt controller. November 08, 2011 1159 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 4 CONN R/W 0 Description Enable Connect Interrupt Value Description 3 SOF R/W 0 1 An interrupt is sent to the interrupt controller when the CONN bit in the USBIS register is set. 0 The CONN interrupt is suppressed and not sent to the interrupt controller. Enable Start-of-Frame Interrupt Value Description 2 BABBLE R/W 1 1 An interrupt is sent to the interrupt controller when the SOF bit in the USBIS register is set. 0 The SOF interrupt is suppressed and not sent to the interrupt controller. Enable Babble Interrupt Value Description 1 RESUME R/W 1 1 An interrupt is sent to the interrupt controller when the BABBLE bit in the USBIS register is set. 0 The BABBLE interrupt is suppressed and not sent to the interrupt controller. Enable RESUME Interrupt Value Description 0 reserved RO 1 An interrupt is sent to the interrupt controller when the RESUME bit in the USBIS register is set. 0 The RESUME interrupt is suppressed and not sent to the interrupt controller. 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 0 OTG B / Device Mode USB Interrupt Enable (USBIE) Base 0x4005.0000 Offset 0x00B Type R/W, reset 0x06 7 6 reserved Type Reset RO 0 RO 0 5 4 3 2 DISCON reserved SOF RESET R/W 0 RO 0 R/W 0 R/W 1 RESUME SUSPEND R/W 1 R/W 0 1160 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 7:6 reserved RO 0x0 5 DISCON R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Enable Disconnect Interrupt Value Description 1 An interrupt is sent to the interrupt controller when the DISCON bit in the USBIS register is set. 0 The DISCON interrupt is suppressed and not sent to the interrupt controller. 4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 SOF R/W 0 Enable Start-of-Frame Interrupt Value Description 2 RESET R/W 1 1 An interrupt is sent to the interrupt controller when the SOF bit in the USBIS register is set. 0 The SOF interrupt is suppressed and not sent to the interrupt controller. Enable RESET Interrupt Value Description 1 RESUME R/W 1 1 An interrupt is sent to the interrupt controller when the RESET bit in the USBIS register is set. 0 The RESET interrupt is suppressed and not sent to the interrupt controller. Enable RESUME Interrupt Value Description 0 SUSPEND R/W 0 1 An interrupt is sent to the interrupt controller when the RESUME bit in the USBIS register is set. 0 The RESUME interrupt is suppressed and not sent to the interrupt controller. Enable SUSPEND Interrupt Value Description 1 An interrupt is sent to the interrupt controller when the SUSPEND bit in the USBIS register is set. 0 The SUSPEND interrupt is suppressed and not sent to the interrupt controller. November 08, 2011 1161 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 9: USB Frame Value (USBFRAME), offset 0x00C OTG A / Host USBFRAME is a 16-bit read-only register that holds the last received frame number. USB Frame Value (USBFRAME) Base 0x4005.0000 Offset 0x00C Type RO, reset 0x0000 OTG B / 15 14 RO 0 RO 0 Device 13 12 11 10 9 8 7 6 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 FRAME Bit/Field Name Type Reset 15:11 reserved RO 0x0 10:0 FRAME RO 0x000 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Frame Number 1162 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 10: USB Endpoint Index (USBEPIDX), offset 0x00E OTG A / Host Each endpoint's buffer can be accessed by configuring a FIFO size and starting address. The USBEPIDX 8-bit register is used with the USBTXFIFOSZ, USBRXFIFOSZ, USBTXFIFOADD, and USBRXFIFOADD registers. USB Endpoint Index (USBEPIDX) OTG B / Device Base 0x4005.0000 Offset 0x00E Type R/W, reset 0x00 7 6 RO 0 RO 0 5 4 3 2 RO 0 R/W 0 R/W 0 reserved Type Reset RO 0 1 0 R/W 0 R/W 0 EPIDX Bit/Field Name Type Reset Description 7:4 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3:0 EPIDX R/W 0x0 Endpoint Index This bit field configures which endpoint is accessed when reading or writing to one of the USB controller's indexed registers. A value of 0x0 corresponds to Endpoint 0 and a value of 0x7 corresponds to Endpoint 7. November 08, 2011 1163 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 11: USB Test Mode (USBTEST), offset 0x00F OTG A / Host USBTEST is an 8-bit register that is primarily used to put the USB controller into one of the four test modes for operation described in the USB 2.0 Specification, in response to a SET FEATURE: USBTESTMODE command. This register is not used in normal operation. Note: Only one of these bits should be set at any time. OTG B / Device OTG A / Host Mode USB Test Mode (USBTEST) Base 0x4005.0000 Offset 0x00F Type R/W, reset 0x00 7 6 5 4 3 FORCEH FIFOACC FORCEFS Type Reset R/W 0 R/W1S 0 R/W 0 2 1 0 RO 0 RO 0 reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset 7 FORCEH R/W 0 Description Force Host Mode Value Description 1 Forces the USB controller to enter Host mode when the SESSION bit is set, regardless of whether the USB controller is connected to any peripheral. The state of the USB0DP and USB0DM signals is ignored. The USB controller then remains in Host mode until the SESSION bit is cleared, even if a Device is disconnected. If the FORCEH bit remains set, the USB controller re-enters Host mode the next time the SESSION bit is set. 0 No effect. While in this mode, status of the bus connection may be read using the DEV bit of the USBDEVCTL register. The operating speed is determined from the FORCEFS bit. 6 FIFOACC R/W1S 0 FIFO Access Value Description 1 Transfers the packet in the endpoint 0 transmit FIFO to the endpoint 0 receive FIFO. 0 No effect. This bit is cleared automatically. 5 FORCEFS R/W 0 Force Full-Speed Mode Value Description 1 Forces the USB controller into Full-Speed mode upon receiving a USB RESET. 0 The USB controller operates at Low Speed. 1164 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 4:0 reserved RO 0x0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. OTG B / Device Mode USB Test Mode (USBTEST) Base 0x4005.0000 Offset 0x00F Type R/W, reset 0x00 7 reserved Type Reset RO 0 6 5 4 3 FIFOACC FORCEFS R/W1S 0 R/W 0 2 1 0 RO 0 RO 0 reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 7 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6 FIFOACC R/W1S 0 FIFO Access Value Description 1 Transfers the packet in the endpoint 0 transmit FIFO to the endpoint 0 receive FIFO. 0 No effect. This bit is cleared automatically. 5 FORCEFS R/W 0 Force Full-Speed Mode Value Description 4:0 reserved RO 0x0 1 Forces the USB controller into Full-Speed mode upon receiving a USB RESET. 0 The USB controller operates at Low Speed. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1165 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 12: USB FIFO Endpoint 0 (USBFIFO0), offset 0x020 Register 13: USB FIFO Endpoint 1 (USBFIFO1), offset 0x024 Register 14: USB FIFO Endpoint 2 (USBFIFO2), offset 0x028 Register 15: USB FIFO Endpoint 3 (USBFIFO3), offset 0x02C Register 16: USB FIFO Endpoint 4 (USBFIFO4), offset 0x030 Register 17: USB FIFO Endpoint 5 (USBFIFO5), offset 0x034 Register 18: USB FIFO Endpoint 6 (USBFIFO6), offset 0x038 Register 19: USB FIFO Endpoint 7 (USBFIFO7), offset 0x03C Important: This register is read-sensitive. See the register description for details. OTG A / Host OTG B / Device These 32-bit registers provide an address for CPU access to the FIFOs for each endpoint. Writing to these addresses loads data into the Transmit FIFO for the corresponding endpoint. Reading from these addresses unloads data from the Receive FIFO for the corresponding endpoint. Transfers to and from FIFOs may be 8-bit, 16-bit or 32-bit as required, and any combination of accesses is allowed provided the data accessed is contiguous. All transfers associated with one packet must be of the same width so that the data is consistently byte-, halfword- or word-aligned. However, the last transfer may contain fewer bytes than the previous transfers in order to complete an odd-byte or odd-word transfer. Depending on the size of the FIFO and the expected maximum packet size, the FIFOs support either single-packet or double-packet buffering (see the section called “Single-Packet Buffering” on page 1128). Burst writing of multiple packets is not supported as flags must be set after each packet is written. Following a STALL response or a transmit error on endpoint 1–7, the associated FIFO is completely flushed. USB FIFO Endpoint 0 (USBFIFO0) Base 0x4005.0000 Offset 0x020 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 EPDATA Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 EPDATA Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type 31:0 EPDATA R/W R/W 0 Reset R/W 0 Description 0x0000.0000 Endpoint Data Writing to this register loads the data into the Transmit FIFO and reading unloads data from the Receive FIFO. 1166 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 20: USB Device Control (USBDEVCTL), offset 0x060 OTG A / Host USBDEVCTL is an 8-bit register used for controlling and monitoring the USB VBUS line. If the PHY is suspended, no PHY clock is received and the VBUS is not sampled. In addition, in Host mode, USBDEVCTL provides the status information for the current operating mode (Host or Device) of the USB controller. If the USB controller is in Host mode, this register also indicates if a full- or low-speed Device has been connected. USB Device Control (USBDEVCTL) Base 0x4005.0000 Offset 0x060 Type R/W, reset 0x80 Type Reset 7 6 5 4 DEV FSDEV LSDEV RO 1 RO 0 RO 0 3 2 VBUS RO 0 HOST RO 0 RO 0 1 0 HOSTREQ SESSION R/W 0 Bit/Field Name Type Reset 7 DEV RO 1 R/W 0 Description Device Mode Value Description 0 The USB controller is operating on the OTG A side of the cable. 1 The USB controller is operating on the OTG B side of the cable. Note: 6 FSDEV RO 0 This value is only valid while a session is in progress. Full-Speed Device Detected Value Description 5 LSDEV RO 0 0 A full-speed Device has not been detected on the port. 1 A full-speed Device has been detected on the port. Low-Speed Device Detected Value Description 4:3 VBUS RO 0x0 0 A low-speed Device has not been detected on the port. 1 A low-speed Device has been detected on the port. VBUS Level Value Description 0x0 Below SessionEnd VBUS is detected as under 0.5 V. 0x1 Above SessionEnd, below AValid VBUS is detected as above 0.5 V and under 1.5 V. 0x2 Above AValid, below VBUSValid VBUS is detected as above 1.5 V and below 4.75 V. 0x3 Above VBUSValid VBUS is detected as above 4.75 V. November 08, 2011 1167 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset Description 2 HOST RO 0 Host Mode Value Description 0 The USB controller is acting as a Device. 1 The USB controller is acting as a Host. Note: 1 HOSTREQ R/W 0 This value is only valid while a session is in progress. Host Request Value Description 0 No effect. 1 Initiates the Host Negotiation when SUSPEND mode is entered. This bit is cleared when Host Negotiation is completed. 0 SESSION R/W 0 Session Start/End When operating as an OTG A device: Value Description 0 When cleared by software, this bit ends a session. 1 When set by software, this bit starts a session. When operating as an OTG B device: Value Description 0 The USB controller has ended a session. When the USB controller is in SUSPEND mode, this bit may be cleared by software to perform a software disconnect. 1 The USB controller has started a session. When set by software, the Session Request Protocol is initiated. Note: Clearing this bit when the USB controller is not suspended results in undefined behavior. 1168 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 21: USB Transmit Dynamic FIFO Sizing (USBTXFIFOSZ), offset 0x062 Register 22: USB Receive Dynamic FIFO Sizing (USBRXFIFOSZ), offset 0x063 OTG A / Host These 8-bit registers allow the selected TX/RX endpoint FIFOs to be dynamically sized. USBEPIDX is used to configure each transmit endpoint's FIFO size. USB Transmit Dynamic FIFO Sizing (USBTXFIFOSZ) OTG B / Base 0x4005.0000 Offset 0x062 Type R/W, reset 0x00 Device 7 6 5 reserved Type Reset RO 0 RO 0 4 3 2 R/W 0 R/W 0 DPB RO 0 R/W 0 1 0 R/W 0 R/W 0 SIZE Bit/Field Name Type Reset 7:5 reserved RO 0x0 4 DPB R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Double Packet Buffer Support Value Description 3:0 SIZE R/W 0x0 0 Only single-packet buffering is supported. 1 Double-packet buffering is supported. Max Packet Size Maximum packet size to be allowed. If DPB = 0, the FIFO also is this size; if DPB = 1, the FIFO is twice this size. Value Packet Size (Bytes) 0x0 8 0x1 16 0x2 32 0x3 64 0x4 128 0x5 256 0x6 512 0x7 1024 0x8 2048 0x9-0xF Reserved November 08, 2011 1169 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 23: USB Transmit FIFO Start Address (USBTXFIFOADD), offset 0x064 Register 24: USB Receive FIFO Start Address (USBRXFIFOADD), offset 0x066 OTG A / Host OTG B / USBTXFIFOADD and USBRXFIFOADD are 16-bit registers that control the start address of the selected transmit and receive endpoint FIFOs. USB Transmit FIFO Start Address (USBTXFIFOADD) Base 0x4005.0000 Offset 0x064 Type R/W, reset 0x0000 Device 15 14 13 RO 0 RO 0 RO 0 12 11 10 9 8 7 6 5 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 ADDR R/W 0 Bit/Field Name Type Reset Description 15:9 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 8:0 ADDR R/W 0x00 Transmit/Receive Start Address Start address of the endpoint FIFO. Value Start Address 0x0 0 0x1 8 0x2 16 0x3 24 0x4 32 0x5 40 0x6 48 0x7 56 0x8 64 ... ... 0x1FF 4095 1170 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 25: USB Connect Timing (USBCONTIM), offset 0x07A OTG A / Host This 8-bit configuration register specifies connection and negotiation delays. USB Connect Timing (USBCONTIM) Base 0x4005.0000 Offset 0x07A Type R/W, reset 0x5C OTG B / 7 6 R/W 0 R/W 1 Device 5 4 3 2 R/W 1 R/W 1 R/W 1 WTCON Type Reset R/W 0 1 0 R/W 0 R/W 0 WTID Bit/Field Name Type Reset 7:4 WTCON R/W 0x5 Description Connect Wait This field configures the wait required to allow for the user’s connect/disconnect filter, in units of 533.3 ns. The default corresponds to 2.667 µs. 3:0 WTID R/W 0xC Wait ID This field configures the delay required from the enable of the ID detection to when the ID value is valid, in units of 4.369 ms. The default corresponds to 52.43 ms. November 08, 2011 1171 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 26: USB OTG VBUS Pulse Timing (USBVPLEN), offset 0x07B This 8-bit configuration register specifies the duration of the VBUS pulsing charge. OTG USB OTG VBUS Pulse Timing (USBVPLEN) Base 0x4005.0000 Offset 0x07B Type R/W, reset 0x3C 7 6 5 4 R/W 0 R/W 0 R/W 1 R/W 1 3 2 1 0 R/W 1 R/W 1 R/W 0 R/W 0 VPLEN Type Reset Bit/Field Name Type Reset Description 7:0 VPLEN R/W 0x3C VBUS Pulse Length This field configures the duration of the VBUS pulsing charge in units of 546.1 µs. The default corresponds to 32.77 ms. 1172 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 27: USB Full-Speed Last Transaction to End of Frame Timing (USBFSEOF), offset 0x07D OTG A / Host OTG B / This 8-bit configuration register specifies the minimum time gap allowed between the start of the last transaction and the EOF for full-speed transactions. USB Full-Speed Last Transaction to End of Frame Timing (USBFSEOF) Base 0x4005.0000 Offset 0x07D Type R/W, reset 0x77 Device 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 FSEOFG Type Reset R/W 0 R/W 1 R/W 1 R/W 1 R/W 0 Bit/Field Name Type Reset Description 7:0 FSEOFG R/W 0x77 Full-Speed End-of-Frame Gap This field is used during full-speed transactions to configure the gap between the last transaction and the End-of-Frame (EOF), in units of 533.3 ns. The default corresponds to 63.46 µs. November 08, 2011 1173 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 28: USB Low-Speed Last Transaction to End of Frame Timing (USBLSEOF), offset 0x07E OTG A / Host OTG B / This 8-bit configuration register specifies the minimum time gap that is to be allowed between the start of the last transaction and the EOF for low-speed transactions. USB Low-Speed Last Transaction to End of Frame Timing (USBLSEOF) Base 0x4005.0000 Offset 0x07E Type R/W, reset 0x72 Device 7 6 5 4 3 2 1 0 R/W 0 R/W 1 R/W 0 LSEOFG Type Reset R/W 0 R/W 1 R/W 1 R/W 1 R/W 0 Bit/Field Name Type Reset Description 7:0 LSEOFG R/W 0x72 Low-Speed End-of-Frame Gap This field is used during low-speed transactions to set the gap between the last transaction and the End-of-Frame (EOF), in units of 1.067 µs. The default corresponds to 121.6 µs. 1174 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 29: USB Transmit Functional Address Endpoint 0 (USBTXFUNCADDR0), offset 0x080 Register 30: USB Transmit Functional Address Endpoint 1 (USBTXFUNCADDR1), offset 0x088 Register 31: USB Transmit Functional Address Endpoint 2 (USBTXFUNCADDR2), offset 0x090 Register 32: USB Transmit Functional Address Endpoint 3 (USBTXFUNCADDR3), offset 0x098 Register 33: USB Transmit Functional Address Endpoint 4 (USBTXFUNCADDR4), offset 0x0A0 Register 34: USB Transmit Functional Address Endpoint 5 (USBTXFUNCADDR5), offset 0x0A8 Register 35: USB Transmit Functional Address Endpoint 6 (USBTXFUNCADDR6), offset 0x0B0 Register 36: USB Transmit Functional Address Endpoint 7 (USBTXFUNCADDR7), offset 0x0B8 OTG A / Host USBTXFUNCADDRn is an 8-bit read/write register that records the address of the target function to be accessed through the associated endpoint (EPn). USBTXFUNCADDRn must be defined for each transmit endpoint that is used. Note: USBTXFUNCADDR0 is used for both receive and transmit for endpoint 0. USB Transmit Functional Address Endpoint 0 (USBTXFUNCADDR0) Base 0x4005.0000 Offset 0x080 Type R/W, reset 0x00 7 6 5 4 Type Reset RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 ADDR reserved R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 7 reserved RO 0 6:0 ADDR R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Device Address Specifies the USB bus address for the target Device. November 08, 2011 1175 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 37: USB Transmit Hub Address Endpoint 0 (USBTXHUBADDR0), offset 0x082 Register 38: USB Transmit Hub Address Endpoint 1 (USBTXHUBADDR1), offset 0x08A Register 39: USB Transmit Hub Address Endpoint 2 (USBTXHUBADDR2), offset 0x092 Register 40: USB Transmit Hub Address Endpoint 3 (USBTXHUBADDR3), offset 0x09A Register 41: USB Transmit Hub Address Endpoint 4 (USBTXHUBADDR4), offset 0x0A2 Register 42: USB Transmit Hub Address Endpoint 5 (USBTXHUBADDR5), offset 0x0AA Register 43: USB Transmit Hub Address Endpoint 6 (USBTXHUBADDR6), offset 0x0B2 Register 44: USB Transmit Hub Address Endpoint 7 (USBTXHUBADDR7), offset 0x0BA OTG A / Host USBTXHUBADDRn is an 8-bit read/write register that, like USBTXHUBPORTn, only must be written when a USB Device is connected to transmit endpoint EPn via a USB 2.0 hub. This register records the address of the USB 2.0 hub through which the target associated with the endpoint is accessed. Note: USBTXHUBADDR0 is used for both receive and transmit for endpoint 0. USB Transmit Hub Address Endpoint 0 (USBTXHUBADDR0) Base 0x4005.0000 Offset 0x082 Type R/W, reset 0x00 7 6 5 4 Type Reset RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 ADDR reserved R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 7 reserved RO 0 6:0 ADDR R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Hub Address This field specifies the USB bus address for the USB 2.0 hub. 1176 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 45: USB Transmit Hub Port Endpoint 0 (USBTXHUBPORT0), offset 0x083 Register 46: USB Transmit Hub Port Endpoint 1 (USBTXHUBPORT1), offset 0x08B Register 47: USB Transmit Hub Port Endpoint 2 (USBTXHUBPORT2), offset 0x093 Register 48: USB Transmit Hub Port Endpoint 3 (USBTXHUBPORT3), offset 0x09B Register 49: USB Transmit Hub Port Endpoint 4 (USBTXHUBPORT4), offset 0x0A3 Register 50: USB Transmit Hub Port Endpoint 5 (USBTXHUBPORT5), offset 0x0AB Register 51: USB Transmit Hub Port Endpoint 6 (USBTXHUBPORT6), offset 0x0B3 Register 52: USB Transmit Hub Port Endpoint 7 (USBTXHUBPORT7), offset 0x0BB OTG A / Host USBTXHUBPORTn is an 8-bit read/write register that, like USBTXHUBADDRn, only must be written when a full- or low-speed Device is connected to transmit endpoint EPn via a USB 2.0 hub. This register records the port of the USB 2.0 hub through which the target associated with the endpoint is accessed. Note: USBTXHUBPORT0 is used for both receive and transmit for endpoint 0. USB Transmit Hub Port Endpoint 0 (USBTXHUBPORT0) Base 0x4005.0000 Offset 0x083 Type R/W, reset 0x00 7 6 5 4 Type Reset RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 PORT reserved R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 7 reserved RO 0 6:0 PORT R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Hub Port This field specifies the USB hub port number. November 08, 2011 1177 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 53: USB Receive Functional Address Endpoint 1 (USBRXFUNCADDR1), offset 0x08C Register 54: USB Receive Functional Address Endpoint 2 (USBRXFUNCADDR2), offset 0x094 Register 55: USB Receive Functional Address Endpoint 3 (USBRXFUNCADDR3), offset 0x09C Register 56: USB Receive Functional Address Endpoint 4 (USBRXFUNCADDR4), offset 0x0A4 Register 57: USB Receive Functional Address Endpoint 5 (USBRXFUNCADDR5), offset 0x0AC Register 58: USB Receive Functional Address Endpoint 6 (USBRXFUNCADDR6), offset 0x0B4 Register 59: USB Receive Functional Address Endpoint 7 (USBRXFUNCADDR7), offset 0x0BC OTG A / Host USBRXFUNCADDRn is an 8-bit read/write register that records the address of the target function accessed through the associated endpoint (EPn). USBRXFUNCADDRn must be defined for each receive endpoint that is used. Note: USBTXFUNCADDR0 is used for both receive and transmit for endpoint 0. USB Receive Functional Address Endpoint 1 (USBRXFUNCADDR1) Base 0x4005.0000 Offset 0x08C Type R/W, reset 0x00 7 6 5 4 R/W 0 R/W 0 R/W 0 RO 0 2 1 0 R/W 0 R/W 0 R/W 0 ADDR reserved Type Reset 3 R/W 0 Bit/Field Name Type Reset 7 reserved RO 0 6:0 ADDR R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Device Address This field specifies the USB bus address for the target Device. 1178 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 60: USB Receive Hub Address Endpoint 1 (USBRXHUBADDR1), offset 0x08E Register 61: USB Receive Hub Address Endpoint 2 (USBRXHUBADDR2), offset 0x096 Register 62: USB Receive Hub Address Endpoint 3 (USBRXHUBADDR3), offset 0x09E Register 63: USB Receive Hub Address Endpoint 4 (USBRXHUBADDR4), offset 0x0A6 Register 64: USB Receive Hub Address Endpoint 5 (USBRXHUBADDR5), offset 0x0AE Register 65: USB Receive Hub Address Endpoint 6 (USBRXHUBADDR6), offset 0x0B6 Register 66: USB Receive Hub Address Endpoint 7 (USBRXHUBADDR7), offset 0x0BE OTG A / Host USBRXHUBADDRn is an 8-bit read/write register that, like USBRXHUBPORTn, only must be written when a full- or low-speed Device is connected to receive endpoint EPn via a USB 2.0 hub. This register records the address of the USB 2.0 hub through which the target associated with the endpoint is accessed. Note: USBTXHUBADDR0 is used for both receive and transmit for endpoint 0. USB Receive Hub Address Endpoint 1 (USBRXHUBADDR1) Base 0x4005.0000 Offset 0x08E Type R/W, reset 0x00 7 6 5 4 R/W 0 R/W 0 R/W 0 RO 0 2 1 0 R/W 0 R/W 0 R/W 0 ADDR reserved Type Reset 3 R/W 0 Bit/Field Name Type Reset 7 reserved RO 0 6:0 ADDR R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Hub Address This field specifies the USB bus address for the USB 2.0 hub. November 08, 2011 1179 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 67: USB Receive Hub Port Endpoint 1 (USBRXHUBPORT1), offset 0x08F Register 68: USB Receive Hub Port Endpoint 2 (USBRXHUBPORT2), offset 0x097 Register 69: USB Receive Hub Port Endpoint 3 (USBRXHUBPORT3), offset 0x09F Register 70: USB Receive Hub Port Endpoint 4 (USBRXHUBPORT4), offset 0x0A7 Register 71: USB Receive Hub Port Endpoint 5 (USBRXHUBPORT5), offset 0x0AF Register 72: USB Receive Hub Port Endpoint 6 (USBRXHUBPORT6), offset 0x0B7 Register 73: USB Receive Hub Port Endpoint 7 (USBRXHUBPORT7), offset 0x0BF OTG A / Host USBRXHUBPORTn is an 8-bit read/write register that, like USBRXHUBADDRn, only must be written when a full- or low-speed Device is connected to receive endpoint EPn via a USB 2.0 hub. This register records the port of the USB 2.0 hub through which the target associated with the endpoint is accessed. Note: USBTXHUBPORT0 is used for both receive and transmit for endpoint 0. USB Receive Hub Port Endpoint 1 (USBRXHUBPORT1) Base 0x4005.0000 Offset 0x08F Type R/W, reset 0x00 7 6 5 4 R/W 0 R/W 0 R/W 0 RO 0 2 1 0 R/W 0 R/W 0 R/W 0 PORT reserved Type Reset 3 R/W 0 Bit/Field Name Type Reset 7 reserved RO 0 6:0 PORT R/W 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Hub Port This field specifies the USB hub port number. 1180 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 74: USB Maximum Transmit Data Endpoint 1 (USBTXMAXP1), offset 0x110 Register 75: USB Maximum Transmit Data Endpoint 2 (USBTXMAXP2), offset 0x120 Register 76: USB Maximum Transmit Data Endpoint 3 (USBTXMAXP3), offset 0x130 Register 77: USB Maximum Transmit Data Endpoint 4 (USBTXMAXP4), offset 0x140 Register 78: USB Maximum Transmit Data Endpoint 5 (USBTXMAXP5), offset 0x150 Register 79: USB Maximum Transmit Data Endpoint 6 (USBTXMAXP6), offset 0x160 Register 80: USB Maximum Transmit Data Endpoint 7 (USBTXMAXP7), offset 0x170 OTG A / Host OTG B / Device The USBTXMAXPn 16-bit register defines the maximum amount of data that can be transferred through the transmit endpoint in a single operation. Bits 10:0 define (in bytes) the maximum payload transmitted in a single transaction. The value set can be up to 1024 bytes but is subject to the constraints placed by the USB Specification on packet sizes for bulk, interrupt and isochronous transfers in full-speed operation. The total amount of data represented by the value written to this register must not exceed the FIFO size for the transmit endpoint, and must not exceed half the FIFO size if double-buffering is required. If this register is changed after packets have been sent from the endpoint, the transmit endpoint FIFO must be completely flushed (using the FLUSH bit in USBTXCSRLn) after writing the new value to this register. Note: USBTXMAXPn must be set to an even number of bytes for proper interrupt generation in µDMA Basic Mode. USB Maximum Transmit Data Endpoint 1 (USBTXMAXP1) Base 0x4005.0000 Offset 0x110 Type R/W, reset 0x0000 15 14 13 12 11 10 9 8 7 6 reserved Type Reset RO 0 RO 0 RO 0 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 MAXLOAD RO 0 RO 0 R/W 0 R/W 0 Bit/Field Name Type Reset 15:11 reserved RO 0x0 10:0 MAXLOAD R/W 0x000 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Maximum Payload This field specifies the maximum payload in bytes per transaction. November 08, 2011 1181 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 81: USB Control and Status Endpoint 0 Low (USBCSRL0), offset 0x102 OTG A / USBCSRL0 is an 8-bit register that provides control and status bits for endpoint 0. Host OTG B / Device OTG A / Host Mode USB Control and Status Endpoint 0 Low (USBCSRL0) Base 0x4005.0000 Offset 0x102 Type W1C, reset 0x00 7 NAKTO Type Reset R/W 0 6 5 STATUS REQPKT R/W 0 4 3 2 1 0 ERROR SETUP STALLED TXRDY RXRDY R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 7 NAKTO R/W 0 Description NAK Timeout Value Description 0 No timeout. 1 Indicates that endpoint 0 is halted following the receipt of NAK responses for longer than the time set by the USBNAKLMT register. Software must clear this bit to allow the endpoint to continue. 6 STATUS R/W 0 STATUS Packet Value Description 0 No transaction. 1 Initiates a STATUS stage transaction. This bit must be set at the same time as the TXRDY or REQPKT bit is set. Setting this bit ensures that the DT bit is set in the USBCSRH0 register so that a DATA1 packet is used for the STATUS stage transaction. This bit is automatically cleared when the STATUS stage is over. 5 REQPKT R/W 0 Request Packet Value Description 0 No request. 1 Requests an IN transaction. This bit is cleared when the RXRDY bit is set. 1182 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 4 ERROR R/W 0 Description Error Value Description 0 No error. 1 Three attempts have been made to perform a transaction with no response from the peripheral. The EP0 bit in the USBTXIS register is also set in this situation. Software must clear this bit. 3 SETUP R/W 0 Setup Packet Value Description 0 Sends an OUT token. 1 Sends a SETUP token instead of an OUT token for the transaction. This bit should be set at the same time as the TXRDY bit is set. Setting this bit always clears the DT bit in the USBCSRH0 register to send a DATA0 packet. 2 STALLED R/W 0 Endpoint Stalled Value Description 0 No handshake has been received. 1 A STALL handshake has been received. Software must clear this bit. 1 TXRDY R/W 0 Transmit Packet Ready Value Description 0 No transmit packet is ready. 1 Software sets this bit after loading a data packet into the TX FIFO. The EP0 bit in the USBTXIS register is also set in this situation. If both the TXRDY and SETUP bits are set, a setup packet is sent. If just TXRDY is set, an OUT packet is sent. This bit is cleared automatically when the data packet has been transmitted. 0 RXRDY R/W 0 Receive Packet Ready Value Description 0 No received packet has been received. 1 Indicates that a data packet has been received in the RX FIFO. The EP0 bit in the USBTXIS register is also set in this situation. Software must clear this bit after the packet has been read from the FIFO to acknowledge that the data has been read from the FIFO. November 08, 2011 1183 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller OTG B / Device Mode USB Control and Status Endpoint 0 Low (USBCSRL0) Base 0x4005.0000 Offset 0x102 Type W1C, reset 0x00 7 6 SETENDC RXRDYC Type Reset W1C 0 W1C 0 5 STALL 4 3 2 SETEND DATAEND STALLED R/W 0 RO 0 R/W 0 R/W 0 1 0 TXRDY RXRDY R/W 0 RO 0 Bit/Field Name Type Reset 7 SETENDC W1C 0 Description Setup End Clear Writing a 1 to this bit clears the SETEND bit. 6 RXRDYC W1C 0 RXRDY Clear Writing a 1 to this bit clears the RXRDY bit. 5 STALL R/W 0 Send Stall Value Description 0 No effect. 1 Terminates the current transaction and transmits the STALL handshake. This bit is cleared automatically after the STALL handshake is transmitted. 4 SETEND RO 0 Setup End Value Description 0 A control transaction has not ended or ended after the DATAEND bit was set. 1 A control transaction has ended before the DATAEND bit has been set. The EP0 bit in the USBTXIS register is also set in this situation. This bit is cleared by writing a 1 to the SETENDC bit. 3 DATAEND R/W 0 Data End Value Description 0 No effect. 1 Set this bit in the following situations: ■ When setting TXRDY for the last data packet ■ When clearing RXRDY after unloading the last data packet ■ When setting TXRDY for a zero-length data packet This bit is cleared automatically. 1184 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 2 STALLED R/W 0 Description Endpoint Stalled Value Description 0 A STALL handshake has not been transmitted. 1 A STALL handshake has been transmitted. Software must clear this bit. 1 TXRDY R/W 0 Transmit Packet Ready Value Description 0 No transmit packet is ready. 1 Software sets this bit after loading an IN data packet into the TX FIFO. The EP0 bit in the USBTXIS register is also set in this situation. This bit is cleared automatically when the data packet has been transmitted. 0 RXRDY RO 0 Receive Packet Ready Value Description 0 No data packet has been received. 1 A data packet has been received. The EP0 bit in the USBTXIS register is also set in this situation. This bit is cleared by writing a 1 to the RXRDYC bit. November 08, 2011 1185 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 82: USB Control and Status Endpoint 0 High (USBCSRH0), offset 0x103 OTG A / USBSR0H is an 8-bit register that provides control and status bits for endpoint 0. Host OTG B / Device OTG A / Host Mode USB Control and Status Endpoint 0 High (USBCSRH0) Base 0x4005.0000 Offset 0x103 Type W1C, reset 0x00 7 6 RO 0 RO 0 5 4 3 RO 0 RO 0 2 reserved Type Reset RO 0 1 0 DTWE DT FLUSH R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 7:3 reserved RO 0x0 2 DTWE R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Data Toggle Write Enable Value Description 0 The DT bit cannot be written. 1 Enables the current state of the endpoint 0 data toggle to be written (see DT bit). This bit is automatically cleared once the new value is written. 1 DT R/W 0 Data Toggle When read, this bit indicates the current state of the endpoint 0 data toggle. If DTWE is set, this bit may be written with the required setting of the data toggle. If DTWE is Low, this bit cannot be written. Care should be taken when writing to this bit as it should only be changed to RESET USB endpoint 0. 1186 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset Description 0 FLUSH R/W 0 Flush FIFO Value Description 0 No effect. 1 Flushes the next packet to be transmitted/read from the endpoint 0 FIFO. The FIFO pointer is reset and the TXRDY/RXRDY bit is cleared. This bit is automatically cleared after the flush is performed. Important: This bit should only be set when TXRDY/RXRDY is set. At other times, it may cause data to be corrupted. OTG B / Device Mode USB Control and Status Endpoint 0 High (USBCSRH0) Base 0x4005.0000 Offset 0x103 Type W1C, reset 0x00 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 0 FLUSH RO 0 RO 0 RO 0 R/W 0 Bit/Field Name Type Reset Description 7:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 FLUSH R/W 0 Flush FIFO Value Description 0 No effect. 1 Flushes the next packet to be transmitted/read from the endpoint 0 FIFO. The FIFO pointer is reset and the TXRDY/RXRDY bit is cleared. This bit is automatically cleared after the flush is performed. Important: This bit should only be set when TXRDY/RXRDY is set. At other times, it may cause data to be corrupted. November 08, 2011 1187 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 83: USB Receive Byte Count Endpoint 0 (USBCOUNT0), offset 0x108 OTG A / Host USBCOUNT0 is an 8-bit read-only register that indicates the number of received data bytes in the endpoint 0 FIFO. The value returned changes as the contents of the FIFO change and is only valid while the RXRDY bit is set. USB Receive Byte Count Endpoint 0 (USBCOUNT0) OTG B / Device Base 0x4005.0000 Offset 0x108 Type RO, reset 0x00 7 6 5 4 RO 0 RO 0 RO 0 RO 0 2 1 0 RO 0 RO 0 RO 0 COUNT reserved Type Reset 3 RO 0 Bit/Field Name Type Reset 7 reserved RO 0 6:0 COUNT RO 0x00 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. FIFO Count COUNT is a read-only value that indicates the number of received data bytes in the endpoint 0 FIFO. 1188 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 84: USB Type Endpoint 0 (USBTYPE0), offset 0x10A OTG A / Host This is an 8-bit register that must be written with the operating speed of the targeted Device being communicated with using endpoint 0. USB Type Endpoint 0 (USBTYPE0) Base 0x4005.0000 Offset 0x10A Type R/W, reset 0x00 7 6 5 4 3 R/W 0 RO 0 RO 0 RO 0 SPEED Type Reset R/W 0 2 1 0 RO 0 RO 0 RO 0 reserved Bit/Field Name Type Reset 7:6 SPEED R/W 0x0 Description Operating Speed This field specifies the operating speed of the target Device. If selected, the target is assumed to have the same connection speed as the USB controller. Value Description 0x0 - 0x1 Reserved 5:0 reserved RO 0x0 0x2 Full 0x3 Low Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1189 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 85: USB NAK Limit (USBNAKLMT), offset 0x10B OTG A / Host USBNAKLMT is an 8-bit register that sets the number of frames after which endpoint 0 should time out on receiving a stream of NAK responses. (Equivalent settings for other endpoints can be made through their USBTXINTERVALn and USBRXINTERVALn registers.) (m-1) The number of frames selected is 2 (where m is the value set in the register, with valid values of 2–16). If the Host receives NAK responses from the target for more frames than the number represented by the limit set in this register, the endpoint is halted. Note: A value of 0 or 1 disables the NAK timeout function. USB NAK Limit (USBNAKLMT) Base 0x4005.0000 Offset 0x10B Type R/W, reset 0x00 7 6 5 4 3 2 RO 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 1 0 R/W 0 R/W 0 NAKLMT R/W 0 Bit/Field Name Type Reset Description 7:5 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4:0 NAKLMT R/W 0x0 EP0 NAK Limit This field specifies the number of frames after receiving a stream of NAK responses. 1190 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 86: USB Transmit Control and Status Endpoint 1 Low (USBTXCSRL1), offset 0x112 Register 87: USB Transmit Control and Status Endpoint 2 Low (USBTXCSRL2), offset 0x122 Register 88: USB Transmit Control and Status Endpoint 3 Low (USBTXCSRL3), offset 0x132 Register 89: USB Transmit Control and Status Endpoint 4 Low (USBTXCSRL4), offset 0x142 Register 90: USB Transmit Control and Status Endpoint 5 Low (USBTXCSRL5), offset 0x152 Register 91: USB Transmit Control and Status Endpoint 6 Low (USBTXCSRL6), offset 0x162 Register 92: USB Transmit Control and Status Endpoint 7 Low (USBTXCSRL7), offset 0x172 OTG A / USBTXCSRLn is an 8-bit register that provides control and status bits for transfers through the currently selected transmit endpoint. Host OTG B / Device OTG A / Host Mode USB Transmit Control and Status Endpoint 1 Low (USBTXCSRL1) Base 0x4005.0000 Offset 0x112 Type R/W, reset 0x00 Type Reset 7 6 5 4 3 2 1 0 NAKTO CLRDT STALLED SETUP FLUSH ERROR FIFONE TXRDY R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 7 NAKTO R/W 0 Description NAK Timeout Value Description 0 No timeout. 1 Bulk endpoints only: Indicates that the transmit endpoint is halted following the receipt of NAK responses for longer than the time set by the NAKLMT field in the USBTXINTERVALn register. Software must clear this bit to allow the endpoint to continue. November 08, 2011 1191 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 6 CLRDT R/W 0 Description Clear Data Toggle Writing a 1 to this bit clears the DT bit in the USBTXCSRHn register. 5 STALLED R/W 0 Endpoint Stalled Value Description 0 A STALL handshake has not been received. 1 Indicates that a STALL handshake has been received. When this bit is set, any µDMA request that is in progress is stopped, the FIFO is completely flushed, and the TXRDY bit is cleared. Software must clear this bit. 4 SETUP R/W 0 Setup Packet Value Description 0 No SETUP token is sent. 1 Sends a SETUP token instead of an OUT token for the transaction. This bit should be set at the same time as the TXRDY bit is set. Note: 3 FLUSH R/W 0 Setting this bit also clears the DT bit in the USBTXCSRHn register. Flush FIFO Value Description 0 No effect. 1 Flushes the latest packet from the endpoint transmit FIFO. The FIFO pointer is reset and the TXRDY bit is cleared. The EPn bit in the USBTXIS register is also set in this situation. This bit may be set simultaneously with the TXRDY bit to abort the packet that is currently being loaded into the FIFO. Note that if the FIFO is double-buffered, FLUSH may have to be set twice to completely clear the FIFO. Important: 2 ERROR R/W 0 This bit should only be set when the TXRDY bit is set. At other times, it may cause data to be corrupted. Error Value Description 0 No error. 1 Three attempts have been made to send a packet and no handshake packet has been received. The TXRDY bit is cleared, the EPn bit in the USBTXIS register is set, and the FIFO is completely flushed in this situation. Software must clear this bit. Note: This is valid only when the endpoint is operating in Bulk or Interrupt mode. 1192 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 FIFONE R/W 0 Description FIFO Not Empty Value Description 0 TXRDY R/W 0 0 The FIFO is empty. 1 At least one packet is in the transmit FIFO. Transmit Packet Ready Value Description 0 No transmit packet is ready. 1 Software sets this bit after loading a data packet into the TX FIFO. This bit is cleared automatically when a data packet has been transmitted. The EPn bit in the USBTXIS register is also set at this point. TXRDY is also automatically cleared prior to loading a second packet into a double-buffered FIFO. OTG B / Device Mode USB Transmit Control and Status Endpoint 1 Low (USBTXCSRL1) Base 0x4005.0000 Offset 0x112 Type R/W, reset 0x00 Type Reset 7 6 5 4 3 2 1 0 reserved CLRDT STALLED STALL FLUSH UNDRN FIFONE TXRDY RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 7 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6 CLRDT R/W 0 Clear Data Toggle Writing a 1 to this bit clears the DT bit in the USBTXCSRHn register. 5 STALLED R/W 0 Endpoint Stalled Value Description 0 A STALL handshake has not been transmitted. 1 A STALL handshake has been transmitted. The FIFO is flushed and the TXRDY bit is cleared. Software must clear this bit. November 08, 2011 1193 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset Description 4 STALL R/W 0 Send STALL Value Description 0 No effect. 1 Issues a STALL handshake to an IN token. Software clears this bit to terminate the STALL condition. Note: 3 FLUSH R/W 0 This bit has no effect in isochronous transfers. Flush FIFO Value Description 0 No effect. 1 Flushes the latest packet from the endpoint transmit FIFO. The FIFO pointer is reset and the TXRDY bit is cleared. The EPn bit in the USBTXIS register is also set in this situation. This bit may be set simultaneously with the TXRDY bit to abort the packet that is currently being loaded into the FIFO. Note that if the FIFO is double-buffered, FLUSH may have to be set twice to completely clear the FIFO. Important: 2 UNDRN R/W 0 This bit should only be set when the TXRDY bit is set. At other times, it may cause data to be corrupted. Underrun Value Description 0 No underrun. 1 An IN token has been received when TXRDY is not set. Software must clear this bit. 1 FIFONE R/W 0 FIFO Not Empty Value Description 0 TXRDY R/W 0 0 The FIFO is empty. 1 At least one packet is in the transmit FIFO. Transmit Packet Ready Value Description 0 No transmit packet is ready. 1 Software sets this bit after loading a data packet into the TX FIFO. This bit is cleared automatically when a data packet has been transmitted. The EPn bit in the USBTXIS register is also set at this point. TXRDY is also automatically cleared prior to loading a second packet into a double-buffered FIFO. 1194 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 93: USB Transmit Control and Status Endpoint 1 High (USBTXCSRH1), offset 0x113 Register 94: USB Transmit Control and Status Endpoint 2 High (USBTXCSRH2), offset 0x123 Register 95: USB Transmit Control and Status Endpoint 3 High (USBTXCSRH3), offset 0x133 Register 96: USB Transmit Control and Status Endpoint 4 High (USBTXCSRH4), offset 0x143 Register 97: USB Transmit Control and Status Endpoint 5 High (USBTXCSRH5), offset 0x153 Register 98: USB Transmit Control and Status Endpoint 6 High (USBTXCSRH6), offset 0x163 Register 99: USB Transmit Control and Status Endpoint 7 High (USBTXCSRH7), offset 0x173 OTG A / USBTXCSRHn is an 8-bit register that provides additional control for transfers through the currently selected transmit endpoint. Host OTG B / Device OTG A / Host Mode USB Transmit Control and Status Endpoint 1 High (USBTXCSRH1) Base 0x4005.0000 Offset 0x113 Type R/W, reset 0x00 7 6 AUTOSET reserved Type Reset R/W 0 5 4 3 2 1 MODE DMAEN FDT DMAMOD DTWE DT R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 Bit/Field Name Type Reset 7 AUTOSET R/W 0 0 Description Auto Set Value Description 0 The TXRDY bit must be set manually. 1 Enables the TXRDY bit to be automatically set when data of the maximum packet size (value in USBTXMAXPn) is loaded into the transmit FIFO. If a packet of less than the maximum packet size is loaded, then the TXRDY bit must be set manually. November 08, 2011 1195 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset Description 6 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5 MODE R/W 0 Mode Value Description 0 Enables the endpoint direction as RX. 1 Enables the endpoint direction as TX. Note: 4 DMAEN R/W 0 This bit only has an effect when the same endpoint FIFO is used for both transmit and receive transactions. DMA Request Enable Value Description 0 Disables the µDMA request for the transmit endpoint. 1 Enables the µDMA request for the transmit endpoint. Note: 3 FDT R/W 0 3 TX and 3 /RX endpoints can be connected to the µDMA module. If this bit is set for a particular endpoint, the DMAATX, DMABTX, or DMACTX field in the USB DMA Select (USBDMASEL) register must be programmed correspondingly. Force Data Toggle Value Description 2 DMAMOD R/W 0 0 No effect. 1 Forces the endpoint DT bit to switch and the data packet to be cleared from the FIFO, regardless of whether an ACK was received. This bit can be used by interrupt transmit endpoints that are used to communicate rate feedback for isochronous endpoints. DMA Request Mode Value Description 0 An interrupt is generated after every µDMA packet transfer. 1 An interrupt is generated only after the entire μDMA transfer is complete. Note: 1 DTWE R/W 0 This bit must not be cleared either before or in the same cycle as the above DMAEN bit is cleared. Data Toggle Write Enable Value Description 0 The DT bit cannot be written. 1 Enables the current state of the transmit endpoint data to be written (see DT bit). This bit is automatically cleared once the new value is written. 1196 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset Description 0 DT R/W 0 Data Toggle When read, this bit indicates the current state of the transmit endpoint data toggle. If DTWE is High, this bit may be written with the required setting of the data toggle. If DTWE is Low, any value written to this bit is ignored. Care should be taken when writing to this bit as it should only be changed to RESET the transmit endpoint. OTG B / Device Mode USB Transmit Control and Status Endpoint 1 High (USBTXCSRH1) Base 0x4005.0000 Offset 0x113 Type R/W, reset 0x00 7 Type Reset 6 5 4 3 2 AUTOSET ISO MODE DMAEN FDT DMAMOD R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 1 0 reserved RO 0 Bit/Field Name Type Reset 7 AUTOSET R/W 0 RO 0 Description Auto Set Value Description 6 ISO R/W 0 0 The TXRDY bit must be set manually. 1 Enables the TXRDY bit to be automatically set when data of the maximum packet size (value in USBTXMAXPn) is loaded into the transmit FIFO. If a packet of less than the maximum packet size is loaded, then the TXRDY bit must be set manually. Isochronous Transfers Value Description 5 MODE R/W 0 0 Enables the transmit endpoint for bulk or interrupt transfers. 1 Enables the transmit endpoint for isochronous transfers. Mode Value Description 0 Enables the endpoint direction as RX. 1 Enables the endpoint direction as TX. Note: This bit only has an effect where the same endpoint FIFO is used for both transmit and receive transactions. November 08, 2011 1197 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 4 DMAEN R/W 0 Description DMA Request Enable Value Description 0 Disables the µDMA request for the transmit endpoint. 1 Enables the µDMA request for the transmit endpoint. Note: 3 FDT R/W 0 3 TX and 3 RX endpoints can be connected to the µDMA module. If this bit is set for a particular endpoint, the DMAATX, DMABTX, or DMACTX field in the USB DMA Select (USBDMASEL) register must be programmed correspondingly. Force Data Toggle Value Description 2 DMAMOD R/W 0 0 No effect. 1 Forces the endpoint DT bit to switch and the data packet to be cleared from the FIFO, regardless of whether an ACK was received. This bit can be used by interrupt transmit endpoints that are used to communicate rate feedback for isochronous endpoints. DMA Request Mode Value Description 0 An interrupt is generated after every µDMA packet transfer. 1 An interrupt is generated only after the entire μDMA transfer is complete. Note: 1:0 reserved RO 0 This bit must not be cleared either before or in the same cycle as the above DMAEN bit is cleared. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1198 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 100: USB Maximum Receive Data Endpoint 1 (USBRXMAXP1), offset 0x114 Register 101: USB Maximum Receive Data Endpoint 2 (USBRXMAXP2), offset 0x124 Register 102: USB Maximum Receive Data Endpoint 3 (USBRXMAXP3), offset 0x134 Register 103: USB Maximum Receive Data Endpoint 4 (USBRXMAXP4), offset 0x144 Register 104: USB Maximum Receive Data Endpoint 5 (USBRXMAXP5), offset 0x154 Register 105: USB Maximum Receive Data Endpoint 6 (USBRXMAXP6), offset 0x164 Register 106: USB Maximum Receive Data Endpoint 7 (USBRXMAXP7), offset 0x174 OTG A / Host OTG B / Device The USBRXMAXPn is a 16-bit register which defines the maximum amount of data that can be transferred through the selected receive endpoint in a single operation. Bits 10:0 define (in bytes) the maximum payload transmitted in a single transaction. The value set can be up to 1024 bytes but is subject to the constraints placed by the USB Specification on packet sizes for bulk, interrupt and isochronous transfers in full-speed operations. The total amount of data represented by the value written to this register must not exceed the FIFO size for the receive endpoint, and must not exceed half the FIFO size if double-buffering is required. Note: USBRXMAXPn must be set to an even number of bytes for proper interrupt generation in µDMA Basic mode. USB Maximum Receive Data Endpoint 1 (USBRXMAXP1) Base 0x4005.0000 Offset 0x114 Type R/W, reset 0x0000 15 14 RO 0 RO 0 13 12 11 10 9 8 7 6 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 MAXLOAD Bit/Field Name Type Reset 15:11 reserved RO 0x0 10:0 MAXLOAD R/W 0x000 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Maximum Payload The maximum payload in bytes per transaction. November 08, 2011 1199 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 107: USB Receive Control and Status Endpoint 1 Low (USBRXCSRL1), offset 0x116 Register 108: USB Receive Control and Status Endpoint 2 Low (USBRXCSRL2), offset 0x126 Register 109: USB Receive Control and Status Endpoint 3 Low (USBRXCSRL3), offset 0x136 Register 110: USB Receive Control and Status Endpoint 4 Low (USBRXCSRL4), offset 0x146 Register 111: USB Receive Control and Status Endpoint 5 Low (USBRXCSRL5), offset 0x156 Register 112: USB Receive Control and Status Endpoint 6 Low (USBRXCSRL6), offset 0x166 Register 113: USB Receive Control and Status Endpoint 7 Low (USBRXCSRL7), offset 0x176 OTG A / USBRXCSRLn is an 8-bit register that provides control and status bits for transfers through the currently selected receive endpoint. Host OTG B / Device OTG A / Host Mode USB Receive Control and Status Endpoint 1 Low (USBRXCSRL1) Base 0x4005.0000 Offset 0x116 Type R/W, reset 0x00 7 CLRDT Type Reset W1C 0 6 5 STALLED REQPKT R/W 0 4 FLUSH R/W 0 R/W 0 3 DATAERR / NAKTO 2 1 0 ERROR FULL RXRDY R/W 0 RO 0 R/W 0 R/W 0 Bit/Field Name Type Reset 7 CLRDT W1C 0 Description Clear Data Toggle Writing a 1 to this bit clears the DT bit in the USBRXCSRHn register. 6 STALLED R/W 0 Endpoint Stalled Value Description 0 A STALL handshake has not been received. 1 A STALL handshake has been received. The EPn bit in the USBRXIS register is also set. Software must clear this bit. 1200 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 5 REQPKT R/W 0 Description Request Packet Value Description 0 No request. 1 Requests an IN transaction. This bit is cleared when RXRDY is set. 4 FLUSH R/W 0 Flush FIFO Value Description 0 No effect. 1 Flushes the next packet to be read from the endpoint receive FIFO. The FIFO pointer is reset and the RXRDY bit is cleared. Note that if the FIFO is double-buffered, FLUSH may have to be set twice to completely clear the FIFO. Important: 3 DATAERR / NAKTO R/W 0 This bit should only be set when the RXRDY bit is set. At other times, it may cause data to be corrupted. Data Error / NAK Timeout Value Description 0 Normal operation. 1 Isochronous endpoints only: Indicates that RXRDY is set and the data packet has a CRC or bit-stuff error. This bit is cleared when RXRDY is cleared. Bulk endpoints only: Indicates that the receive endpoint is halted following the receipt of NAK responses for longer than the time set by the NAKLMT field in the USBRXINTERVALn register. Software must clear this bit to allow the endpoint to continue. 2 ERROR R/W 0 Error Value Description 0 No error. 1 Three attempts have been made to receive a packet and no data packet has been received. The EPn bit in the USBRXIS register is set in this situation. Software must clear this bit. Note: 1 FULL RO 0 This bit is only valid when the receive endpoint is operating in Bulk or Interrupt mode. In Isochronous mode, it always returns zero. FIFO Full Value Description 0 The receive FIFO is not full. 1 No more packets can be loaded into the receive FIFO. November 08, 2011 1201 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 0 RXRDY R/W 0 Description Receive Packet Ready Value Description 0 No data packet has been received. 1 A data packet has been received. The EPn bit in the USBRXIS register is also set in this situation. If the AUTOCLR bit in the USBRXCSRHn register is set, then the this bit is automatically cleared when a packet of USBRXMAXPn bytes has been unloaded from the receive FIFO. If the AUTOCLR bit is clear, or if packets of less than the maximum packet size are unloaded, then software must clear this bit manually when the packet has been unloaded from the receive FIFO. OTG B / Device Mode USB Receive Control and Status Endpoint 1 Low (USBRXCSRL1) Base 0x4005.0000 Offset 0x116 Type R/W, reset 0x00 Type Reset 7 6 5 CLRDT STALLED STALL W1C 0 R/W 0 R/W 0 4 3 FLUSH DATAERR R/W 0 2 1 0 OVER FULL RXRDY R/W 0 RO 0 R/W 0 RO 0 Bit/Field Name Type Reset 7 CLRDT W1C 0 Description Clear Data Toggle Writing a 1 to this bit clears the DT bit in the USBRXCSRHn register. 6 STALLED R/W 0 Endpoint Stalled Value Description 0 A STALL handshake has not been transmitted. 1 A STALL handshake has been transmitted. Software must clear this bit. 5 STALL R/W 0 Send STALL Value Description 0 No effect. 1 Issues a STALL handshake. Software must clear this bit to terminate the STALL condition. Note: This bit has no effect where the endpoint is being used for isochronous transfers. 1202 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset Description 4 FLUSH R/W 0 Flush FIFO Value Description 0 No effect. 1 Flushes the next packet from the endpoint receive FIFO. The FIFO pointer is reset and the RXRDY bit is cleared. The CPU writes a 1 to this bit to flush the next packet to be read from the endpoint receive FIFO. The FIFO pointer is reset and the RXRDY bit is cleared. Note that if the FIFO is double-buffered, FLUSH may have to be set twice to completely clear the FIFO. Important: 3 DATAERR RO 0 This bit should only be set when the RXRDY bit is set. At other times, it may cause data to be corrupted. Data Error Value Description 0 Normal operation. 1 Indicates that RXRDY is set and the data packet has a CRC or bit-stuff error. This bit is cleared when RXRDY is cleared. Note: 2 OVER R/W 0 This bit is only valid when the endpoint is operating in Isochronous mode. In Bulk mode, it always returns zero. Overrun Value Description 0 No overrun error. 1 Indicates that an OUT packet cannot be loaded into the receive FIFO. Software must clear this bit. Note: 1 FULL RO 0 This bit is only valid when the endpoint is operating in Isochronous mode. In Bulk mode, it always returns zero. FIFO Full Value Description 0 The receive FIFO is not full. 1 No more packets can be loaded into the receive FIFO. November 08, 2011 1203 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 0 RXRDY R/W 0 Description Receive Packet Ready Value Description 0 No data packet has been received. 1 A data packet has been received. The EPn bit in the USBRXIS register is also set in this situation. If the AUTOCLR bit in the USBRXCSRHn register is set, then the this bit is automatically cleared when a packet of USBRXMAXPn bytes has been unloaded from the receive FIFO. If the AUTOCLR bit is clear, or if packets of less than the maximum packet size are unloaded, then software must clear this bit manually when the packet has been unloaded from the receive FIFO. 1204 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 114: USB Receive Control and Status Endpoint 1 High (USBRXCSRH1), offset 0x117 Register 115: USB Receive Control and Status Endpoint 2 High (USBRXCSRH2), offset 0x127 Register 116: USB Receive Control and Status Endpoint 3 High (USBRXCSRH3), offset 0x137 Register 117: USB Receive Control and Status Endpoint 4 High (USBRXCSRH4), offset 0x147 Register 118: USB Receive Control and Status Endpoint 5 High (USBRXCSRH5), offset 0x157 Register 119: USB Receive Control and Status Endpoint 6 High (USBRXCSRH6), offset 0x167 Register 120: USB Receive Control and Status Endpoint 7 High (USBRXCSRH7), offset 0x177 OTG A / USBRXCSRHn is an 8-bit register that provides additional control and status bits for transfers through the currently selected receive endpoint. Host OTG B / Device OTG A / Host Mode USB Receive Control and Status Endpoint 1 High (USBRXCSRH1) Base 0x4005.0000 Offset 0x117 Type R/W, reset 0x00 7 6 5 AUTOCL AUTORQ DMAEN Type Reset R/W 0 R/W 0 R/W 0 4 3 2 PIDERR DMAMOD RO 0 R/W 0 1 0 DTWE DT reserved RO 0 RO 0 RO 0 November 08, 2011 1205 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset Description 7 AUTOCL R/W 0 Auto Clear Value Description 6 AUTORQ R/W 0 0 No effect. 1 Enables the RXRDY bit to be automatically cleared when a packet of USBRXMAXPn bytes has been unloaded from the receive FIFO. When packets of less than the maximum packet size are unloaded, RXRDY must be cleared manually. Care must be taken when using µDMA to unload the receive FIFO as data is read from the receive FIFO in 4 byte chunks regardless of the value of the MAXLOAD field in the USBRXMAXPn register, see “DMA Operation” on page 1137. Auto Request Value Description 0 No effect. 1 Enables the REQPKT bit to be automatically set when the RXRDY bit is cleared. Note: 5 DMAEN R/W 0 This bit is automatically cleared when a short packet is received. DMA Request Enable Value Description 0 Disables the µDMA request for the receive endpoint. 1 Enables the µDMA request for the receive endpoint. Note: 4 PIDERR RO 0 3 TX and 3 RX endpoints can be connected to the µDMA module. If this bit is set for a particular endpoint, the DMAARX, DMABRX, or DMACRX field in the USB DMA Select (USBDMASEL) register must be programmed correspondingly. PID Error Value Description 0 No error. 1 Indicates a PID error in the received packet of an isochronous transaction. This bit is ignored in bulk or interrupt transactions. 3 DMAMOD R/W 0 DMA Request Mode Value Description 0 An interrupt is generated after every µDMA packet transfer. 1 An interrupt is generated only after the entire μDMA transfer is complete. Note: This bit must not be cleared either before or in the same cycle as the above DMAEN bit is cleared. 1206 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 2 DTWE RO 0 Description Data Toggle Write Enable Value Description 0 The DT bit cannot be written. 1 Enables the current state of the receive endpoint data to be written (see DT bit). This bit is automatically cleared once the new value is written. 1 DT RO 0 Data Toggle When read, this bit indicates the current state of the receive data toggle. If DTWE is High, this bit may be written with the required setting of the data toggle. If DTWE is Low, any value written to this bit is ignored. Care should be taken when writing to this bit as it should only be changed to RESET the receive endpoint. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. OTG B / Device Mode USB Receive Control and Status Endpoint 1 High (USBRXCSRH1) Base 0x4005.0000 Offset 0x117 Type R/W, reset 0x00 7 Type Reset 6 5 4 AUTOCL ISO DMAEN R/W 0 R/W 0 R/W 0 DISNYET / PIDERR R/W 0 3 2 DMAMOD R/W 0 1 0 reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 7 AUTOCL R/W 0 Auto Clear Value Description 6 ISO R/W 0 0 No effect. 1 Enables the RXRDY bit to be automatically cleared when a packet of USBRXMAXPn bytes has been unloaded from the receive FIFO. When packets of less than the maximum packet size are unloaded, RXRDY must be cleared manually. Care must be taken when using µDMA to unload the receive FIFO as data is read from the receive FIFO in 4 byte chunks regardless of the value of the MAXLOAD field in the USBRXMAXPn register, see “DMA Operation” on page 1137. Isochronous Transfers Value Description 0 Enables the receive endpoint for isochronous transfers. 1 Enables the receive endpoint for bulk/interrupt transfers. November 08, 2011 1207 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 5 DMAEN R/W 0 Description DMA Request Enable Value Description 0 Disables the µDMA request for the receive endpoint. 1 Enables the µDMA request for the receive endpoint. Note: 4 DISNYET / PIDERR R/W 0 3 TX and 3 RX endpoints can be connected to the µDMA module. If this bit is set for a particular endpoint, the DMAARX, DMABRX, or DMACRX field in the USB DMA Select (USBDMASEL) register must be programmed correspondingly. Disable NYET / PID Error Value Description 0 No effect. 1 For bulk or interrupt transactions: Disables the sending of NYET handshakes. When this bit is set, all successfully received packets are acknowledged, including at the point at which the FIFO becomes full. For isochronous transactions: Indicates a PID error in the received packet. 3 DMAMOD R/W 0 DMA Request Mode Value Description 0 An interrupt is generated after every µDMA packet transfer. 1 An interrupt is generated only after the entire μDMA transfer is complete. Note: 2:0 reserved RO 0x0 This bit must not be cleared either before or in the same cycle as the above DMAEN bit is cleared. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1208 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 121: USB Receive Byte Count Endpoint 1 (USBRXCOUNT1), offset 0x118 Register 122: USB Receive Byte Count Endpoint 2 (USBRXCOUNT2), offset 0x128 Register 123: USB Receive Byte Count Endpoint 3 (USBRXCOUNT3), offset 0x138 Register 124: USB Receive Byte Count Endpoint 4 (USBRXCOUNT4), offset 0x148 Register 125: USB Receive Byte Count Endpoint 5 (USBRXCOUNT5), offset 0x158 Register 126: USB Receive Byte Count Endpoint 6 (USBRXCOUNT6), offset 0x168 Register 127: USB Receive Byte Count Endpoint 7 (USBRXCOUNT7), offset 0x178 OTG A / Host Note: The value returned changes as the FIFO is unloaded and is only valid while the RXRDY bit in the USBRXCSRLn register is set. OTG B / USBRXCOUNTn is a 16-bit read-only register that holds the number of data bytes in the packet currently in line to be read from the receive FIFO. If the packet is transmitted as multiple bulk packets, the number given is for the combined packet. Device USB Receive Byte Count Endpoint 1 (USBRXCOUNT1) Base 0x4005.0000 Offset 0x118 Type RO, reset 0x0000 15 14 13 12 11 10 9 8 7 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 COUNT Bit/Field Name Type Reset 15:13 reserved RO 0x0 12:0 COUNT RO 0x000 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Receive Packet Count Indicates the number of bytes in the receive packet. November 08, 2011 1209 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 128: USB Host Transmit Configure Type Endpoint 1 (USBTXTYPE1), offset 0x11A Register 129: USB Host Transmit Configure Type Endpoint 2 (USBTXTYPE2), offset 0x12A Register 130: USB Host Transmit Configure Type Endpoint 3 (USBTXTYPE3), offset 0x13A Register 131: USB Host Transmit Configure Type Endpoint 4 (USBTXTYPE4), offset 0x14A Register 132: USB Host Transmit Configure Type Endpoint 5 (USBTXTYPE5), offset 0x15A Register 133: USB Host Transmit Configure Type Endpoint 6 (USBTXTYPE6), offset 0x16A Register 134: USB Host Transmit Configure Type Endpoint 7 (USBTXTYPE7), offset 0x17A OTG A / Host USBTXTYPEn is an 8-bit register that must be written with the endpoint number to be targeted by the endpoint, the transaction protocol to use for the currently selected transmit endpoint, and its operating speed. USB Host Transmit Configure Type Endpoint 1 (USBTXTYPE1) Base 0x4005.0000 Offset 0x11A Type R/W, reset 0x00 7 6 SPEED Type Reset R/W 0 R/W 0 5 4 3 2 PROTO R/W 0 R/W 0 1 0 R/W 0 R/W 0 TEP R/W 0 R/W 0 Bit/Field Name Type Reset 7:6 SPEED R/W 0x0 Description Operating Speed This bit field specifies the operating speed of the target Device: Value Description 0x0 Default The target is assumed to be using the same connection speed as the USB controller. 0x1 Reserved 0x2 Full 0x3 Low 1210 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 5:4 PROTO R/W 0x0 Description Protocol Software must configure this bit field to select the required protocol for the transmit endpoint: Value Description 3:0 TEP R/W 0x0 0x0 Control 0x1 Isochronous 0x2 Bulk 0x3 Interrupt Target Endpoint Number Software must configure this value to the endpoint number contained in the transmit endpoint descriptor returned to the USB controller during Device enumeration. November 08, 2011 1211 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 135: USB Host Transmit Interval Endpoint 1 (USBTXINTERVAL1), offset 0x11B Register 136: USB Host Transmit Interval Endpoint 2 (USBTXINTERVAL2), offset 0x12B Register 137: USB Host Transmit Interval Endpoint 3 (USBTXINTERVAL3), offset 0x13B Register 138: USB Host Transmit Interval Endpoint 4 (USBTXINTERVAL4), offset 0x14B Register 139: USB Host Transmit Interval Endpoint 5 (USBTXINTERVAL5), offset 0x15B Register 140: USB Host Transmit Interval Endpoint 6 (USBTXINTERVAL6), offset 0x16B Register 141: USB Host Transmit Interval Endpoint 7 (USBTXINTERVAL7), offset 0x17B OTG A / Host USBTXINTERVALn is an 8-bit register that, for interrupt and isochronous transfers, defines the polling interval for the currently selected transmit endpoint. For bulk endpoints, this register defines the number of frames after which the endpoint should time out on receiving a stream of NAK responses. The USBTXINTERVALn register value defines a number of frames, as follows: Transfer Type Interrupt Speed Valid values (m) Interpretation Low-Speed or Full-Speed 0x01 – 0xFF The polling interval is m frames. Isochronous Full-Speed 0x01 – 0x10 The polling interval is 2(m-1) frames. Bulk Full-Speed 0x02 – 0x10 The NAK Limit is 2(m-1) frames. A value of 0 or 1 disables the NAK timeout function. USB Host Transmit Interval Endpoint 1 (USBTXINTERVAL1) Base 0x4005.0000 Offset 0x11B Type R/W, reset 0x00 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 TXPOLL / NAKLMT Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 7:0 TXPOLL / NAKLMT R/W 0x00 TX Polling / NAK Limit The polling interval for interrupt/isochronous transfers; the NAK limit for bulk transfers. See table above for valid entries; other values are reserved. 1212 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 142: USB Host Configure Receive Type Endpoint 1 (USBRXTYPE1), offset 0x11C Register 143: USB Host Configure Receive Type Endpoint 2 (USBRXTYPE2), offset 0x12C Register 144: USB Host Configure Receive Type Endpoint 3 (USBRXTYPE3), offset 0x13C Register 145: USB Host Configure Receive Type Endpoint 4 (USBRXTYPE4), offset 0x14C Register 146: USB Host Configure Receive Type Endpoint 5 (USBRXTYPE5), offset 0x15C Register 147: USB Host Configure Receive Type Endpoint 6 (USBRXTYPE6), offset 0x16C Register 148: USB Host Configure Receive Type Endpoint 7 (USBRXTYPE7), offset 0x17C OTG A / Host USBRXTYPEn is an 8-bit register that must be written with the endpoint number to be targeted by the endpoint, the transaction protocol to use for the currently selected receive endpoint, and its operating speed. USB Host Configure Receive Type Endpoint 1 (USBRXTYPE1) Base 0x4005.0000 Offset 0x11C Type R/W, reset 0x00 7 6 SPEED Type Reset R/W 0 R/W 0 5 4 3 2 PROTO R/W 0 R/W 0 1 0 R/W 0 R/W 0 TEP R/W 0 R/W 0 Bit/Field Name Type Reset 7:6 SPEED R/W 0x0 Description Operating Speed This bit field specifies the operating speed of the target Device: Value Description 0x0 Default The target is assumed to be using the same connection speed as the USB controller. 0x1 Reserved 0x2 Full 0x3 Low November 08, 2011 1213 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 5:4 PROTO R/W 0x0 Description Protocol Software must configure this bit field to select the required protocol for the receive endpoint: Value Description 3:0 TEP R/W 0x0 0x0 Control 0x1 Isochronous 0x2 Bulk 0x3 Interrupt Target Endpoint Number Software must set this value to the endpoint number contained in the receive endpoint descriptor returned to the USB controller during Device enumeration. 1214 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 149: USB Host Receive Polling Interval Endpoint 1 (USBRXINTERVAL1), offset 0x11D Register 150: USB Host Receive Polling Interval Endpoint 2 (USBRXINTERVAL2), offset 0x12D Register 151: USB Host Receive Polling Interval Endpoint 3 (USBRXINTERVAL3), offset 0x13D Register 152: USB Host Receive Polling Interval Endpoint 4 (USBRXINTERVAL4), offset 0x14D Register 153: USB Host Receive Polling Interval Endpoint 5 (USBRXINTERVAL5), offset 0x15D Register 154: USB Host Receive Polling Interval Endpoint 6 (USBRXINTERVAL6), offset 0x16D Register 155: USB Host Receive Polling Interval Endpoint 7 (USBRXINTERVAL7), offset 0x17D OTG A / Host USBRXINTERVALn is an 8-bit register that, for interrupt and isochronous transfers, defines the polling interval for the currently selected receive endpoint. For bulk endpoints, this register defines the number of frames after which the endpoint should time out on receiving a stream of NAK responses. The USBRXINTERVALn register value defines a number of frames, as follows: Transfer Type Interrupt Speed Valid values (m) Interpretation Low-Speed or Full-Speed 0x01 – 0xFF The polling interval is m frames. Isochronous Full-Speed 0x01 – 0x10 The polling interval is 2(m-1) frames. Bulk Full-Speed 0x02 – 0x10 The NAK Limit is 2(m-1) frames. A value of 0 or 1 disables the NAK timeout function. USB Host Receive Polling Interval Endpoint 1 (USBRXINTERVAL1) Base 0x4005.0000 Offset 0x11D Type R/W, reset 0x00 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 TXPOLL / NAKLMT Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 7:0 TXPOLL / NAKLMT R/W 0x00 RX Polling / NAK Limit The polling interval for interrupt/isochronous transfers; the NAK limit for bulk transfers. See table above for valid entries; other values are reserved. November 08, 2011 1215 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 156: USB Request Packet Count in Block Transfer Endpoint 1 (USBRQPKTCOUNT1), offset 0x304 Register 157: USB Request Packet Count in Block Transfer Endpoint 2 (USBRQPKTCOUNT2), offset 0x308 Register 158: USB Request Packet Count in Block Transfer Endpoint 3 (USBRQPKTCOUNT3), offset 0x30C Register 159: USB Request Packet Count in Block Transfer Endpoint 4 (USBRQPKTCOUNT4), offset 0x310 Register 160: USB Request Packet Count in Block Transfer Endpoint 5 (USBRQPKTCOUNT5), offset 0x314 Register 161: USB Request Packet Count in Block Transfer Endpoint 6 (USBRQPKTCOUNT6), offset 0x318 Register 162: USB Request Packet Count in Block Transfer Endpoint 7 (USBRQPKTCOUNT7), offset 0x31C OTG A / Host This 16-bit read/write register is used in Host mode to specify the number of packets that are to be transferred in a block transfer of one or more bulk packets to receive endpoint n. The USB controller uses the value recorded in this register to determine the number of requests to issue where the AUTORQ bit in the USBRXCSRHn register has been set. See “IN Transactions as a Host” on page 1133. Note: Multiple packets combined into a single bulk packet within the FIFO count as one packet. USB Request Packet Count in Block Transfer Endpoint 1 (USBRQPKTCOUNT1) Base 0x4005.0000 Offset 0x304 Type R/W, reset 0x0000 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 COUNT Type Reset Bit/Field Name Type Reset 15:0 COUNT R/W 0x0000 Description Block Transfer Packet Count Sets the number of packets of the size defined by the MAXLOAD bit field that are to be transferred in a block transfer. Note: This is only used in Host mode when AUTORQ is set. The bit has no effect in Device mode or when AUTORQ is not set. 1216 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 163: USB Receive Double Packet Buffer Disable (USBRXDPKTBUFDIS), offset 0x340 OTG A / Host USBRXDPKTBUFDIS is a 16-bit register that indicates which of the receive endpoints have disabled the double-packet buffer functionality (see the section called “Double-Packet Buffering” on page 1129). USB Receive Double Packet Buffer Disable (USBRXDPKTBUFDIS) OTG B / Base 0x4005.0000 Offset 0x340 Type R/W, reset 0x0000 Device 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 reserved R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 Bit/Field Name Type Reset Description 15:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 EP7 R/W 0 EP7 RX Double-Packet Buffer Disable Value Description 6 EP6 R/W 0 0 Disables double-packet buffering. 1 Enables double-packet buffering. EP6 RX Double-Packet Buffer Disable Same description as EP7. 5 EP5 R/W 0 EP5 RX Double-Packet Buffer Disable Same description as EP7. 4 EP4 R/W 0 EP4 RX Double-Packet Buffer Disable Same description as EP7. 3 EP3 R/W 0 EP3 RX Double-Packet Buffer Disable Same description as EP7. 2 EP2 R/W 0 EP2 RX Double-Packet Buffer Disable Same description as EP7. 1 EP1 R/W 0 EP1 RX Double-Packet Buffer Disable Same description as EP7. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1217 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 164: USB Transmit Double Packet Buffer Disable (USBTXDPKTBUFDIS), offset 0x342 OTG A / Host USBTXDPKTBUFDIS is a 16-bit register that indicates which of the transmit endpoints have disabled the double-packet buffer functionality (see the section called “Double-Packet Buffering” on page 1128). USB Transmit Double Packet Buffer Disable (USBTXDPKTBUFDIS) OTG B / Base 0x4005.0000 Offset 0x342 Type R/W, reset 0x0000 Device 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 reserved R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 Bit/Field Name Type Reset Description 15:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 EP7 R/W 0 EP7 TX Double-Packet Buffer Disable Value Description 6 EP6 R/W 0 0 Disables double-packet buffering. 1 Enables double-packet buffering. EP6 TX Double-Packet Buffer Disable Same description as EP7. 5 EP5 R/W 0 EP5 TX Double-Packet Buffer Disable Same description as EP7. 4 EP4 R/W 0 EP4 TX Double-Packet Buffer Disable Same description as EP7. 3 EP3 R/W 0 EP3 TX Double-Packet Buffer Disable Same description as EP7. 2 EP2 R/W 0 EP2 TX Double-Packet Buffer Disable Same description as EP7. 1 EP1 R/W 0 EP1 TX Double-Packet Buffer Disable Same description as EP7. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1218 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 165: USB External Power Control (USBEPC), offset 0x400 OTG A / Host This 32-bit register specifies the function of the two-pin external power interface (USB0EPEN and USB0PFLT). The assertion of the power fault input may generate an automatic action, as controlled by the hardware configuration registers. The automatic action is necessary because the fault condition may require a response faster than one provided by firmware. OTG B / USB External Power Control (USBEPC) Device Base 0x4005.0000 Offset 0x400 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved EPENDE RO 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 PFLTACT Bit/Field Name Type Reset 31:10 reserved RO 0x0000.0 9:8 PFLTACT R/W 0x0 reserved R/W 0 PFLTAEN PFLTSEN PFLTEN RO 0 R/W 0 R/W 0 R/W 0 EPEN R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Power Fault Action This bit field specifies how the USB0EPEN signal is changed when detecting a USB power fault. Value Description 0x0 Unchanged USB0EPEN is controlled by the combination of the EPEN and EPENDE bits. 0x1 Tristate USB0EPEN is undriven (tristate). 0x2 Low USB0EPEN is driven Low. 0x3 High USB0EPEN is driven High. 7 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1219 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Bit/Field Name Type Reset 6 PFLTAEN R/W 0 Description Power Fault Action Enable This bit specifies whether a USB power fault triggers any automatic corrective action regarding the driven state of the USB0EPEN signal. Value Description 0 Disabled USB0EPEN is controlled by the combination of the EPEN and EPENDE bits. 1 Enabled The USB0EPEN output is automatically changed to the state specified by the PFLTACT field. 5 PFLTSEN R/W 0 Power Fault Sense This bit specifies the logical sense of the USB0PFLT input signal that indicates an error condition. The complementary state is the inactive state. Value Description 0 Low Fault If USB0PFLT is driven Low, the power fault is signaled internally (if enabled by the PFLTEN bit). 1 High Fault If USB0PFLT is driven High, the power fault is signaled internally (if enabled by the PFLTEN bit). 4 PFLTEN R/W 0 Power Fault Input Enable This bit specifies whether the USB0PFLT input signal is used in internal logic. Value Description 0 Not Used The USB0PFLT signal is ignored. 1 Used The USB0PFLT signal is used internally. 3 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1220 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 2 EPENDE R/W 0 Description EPEN Drive Enable This bit specifies whether the USB0EPEN signal is driven or undriven (tristate). When driven, the signal value is specified by the EPEN field. When not driven, the EPEN field is ignored and the USB0EPEN signal is placed in a high-impedance state. Value Description 0 Not Driven The USB0EPEN signal is high impedance. 1 Driven The USB0EPEN signal is driven to the logical value specified by the value of the EPEN field. The USB0EPEN signal is undriven at reset because the sense of the external power supply enable is unknown. By adding the high-impedance state, system designers may bias the power supply enable to the disabled state using a large resistor (100 kΩ) and later configure and drive the output signal to enable the power supply. 1:0 EPEN R/W 0x0 External Power Supply Enable Configuration This bit field specifies and controls the logical value driven on the USB0EPEN signal. Value Description 0x0 Power Enable Active Low The USB0EPEN signal is driven Low if the EPENDE bit is set. 0x1 Power Enable Active High The USB0EPEN signal is driven High if the EPENDE bit is set. 0x2 Power Enable High if VBUS Low The USB0EPEN signal is driven High when the A device is not recognized. 0x3 Power Enable High if VBUS High The USB0EPEN signal is driven High when the A device is recognized. November 08, 2011 1221 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 166: USB External Power Control Raw Interrupt Status (USBEPCRIS), offset 0x404 OTG A / This 32-bit register specifies the unmasked interrupt status of the two-pin external power interface. USB External Power Control Raw Interrupt Status (USBEPCRIS) Host Base 0x4005.0000 Offset 0x404 Type RO, reset 0x0000.0000 OTG B / 31 30 29 28 27 26 25 Device 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 PF RO 0 RO 0 RO 0 0 PF RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. USB Power Fault Interrupt Status Value Description 1 A Power Fault status has been detected. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the PF bit in the USBEPCISC register. 1222 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 167: USB External Power Control Interrupt Mask (USBEPCIM), offset 0x408 OTG A / This 32-bit register specifies the interrupt mask of the two-pin external power interface. USB External Power Control Interrupt Mask (USBEPCIM) Host Base 0x4005.0000 Offset 0x408 Type R/W, reset 0x0000.0000 OTG B / 31 30 29 28 27 26 25 Device 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 PF R/W 0 RO 0 RO 0 PF RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. USB Power Fault Interrupt Mask Value Description 1 The raw interrupt signal from a detected power fault is sent to the interrupt controller. 0 A detected power fault does not affect the interrupt status. November 08, 2011 1223 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 168: USB External Power Control Interrupt Status and Clear (USBEPCISC), offset 0x40C OTG A / Host This 32-bit register specifies the masked interrupt status of the two-pin external power interface. It also provides a method to clear the interrupt state. USB External Power Control Interrupt Status and Clear (USBEPCISC) OTG B / Base 0x4005.0000 Offset 0x40C Type R/W, reset 0x0000.0000 Device 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 PF R/W1C 0 RO 0 RO 0 0 PF RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. USB Power Fault Interrupt Status and Clear Value Description 1 The PF bits in the USBEPCRIS and USBEPCIM registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the PF bit in the USBEPCRIS register. 1224 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 169: USB Device RESUME Raw Interrupt Status (USBDRRIS), offset 0x410 OTG A / Host The USBDRRIS 32-bit register is the raw interrupt status register. On a read, this register gives the current raw status value of the corresponding interrupt prior to masking. A write has no effect. USB Device RESUME Raw Interrupt Status (USBDRRIS) OTG B / Base 0x4005.0000 Offset 0x410 Type RO, reset 0x0000.0000 Device 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 RESUME RO 0 RO 0 RO 0 0 RESUME RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. RESUME Interrupt Status Value Description 1 A RESUME status has been detected. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the RESUME bit in the USBDRISC register. November 08, 2011 1225 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 170: USB Device RESUME Interrupt Mask (USBDRIM), offset 0x414 OTG A / Host The USBDRIM 32-bit register is the masked interrupt status register. On a read, this register gives the current value of the mask on the corresponding interrupt. Setting a bit sets the mask, preventing the interrupt from being signaled to the interrupt controller. Clearing a bit clears the corresponding mask, enabling the interrupt to be sent to the interrupt controller. OTG B / USB Device RESUME Interrupt Mask (USBDRIM) Device Base 0x4005.0000 Offset 0x414 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 RESUME R/W 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 RESUME R/W 0 RESUME Interrupt Mask Value Description 1 The raw interrupt signal from a detected RESUME is sent to the interrupt controller. This bit should only be set when a SUSPEND has been detected (the SUSPEND bit in the USBIS register is set). 0 A detected RESUME does not affect the interrupt status. 1226 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 171: USB Device RESUME Interrupt Status and Clear (USBDRISC), offset 0x418 OTG A / Host The USBDRISC 32-bit register is the interrupt clear register. On a write of 1, the corresponding interrupt is cleared. A write of 0 has no effect. USB Device RESUME Interrupt Status and Clear (USBDRISC) OTG B / Base 0x4005.0000 Offset 0x418 Type W1C, reset 0x0000.0000 Device 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 RESUME R/W1C 0 RO 0 RO 0 0 RESUME RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. RESUME Interrupt Status and Clear Value Description 1 The RESUME bits in the USBDRRIS and USBDRCIM registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the RESUME bit in the USBDRCRIS register. November 08, 2011 1227 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 172: USB General-Purpose Control and Status (USBGPCS), offset 0x41C OTG A / USBGPCS provides the state of the internal ID signal. Note: Host OTG B / Device When used in OTG mode, USB0VBUS and USB0ID do not require any configuration as they are dedicated pins for the USB controller and directly connect to the USB connector's VBUS and ID signals. If the USB controller is used as either a dedicated Host or Device, the DEVMODOTG and DEVMOD bits in the USB General-Purpose Control and Status (USBGPCS) register can be used to connect the USB0VBUS and USB0ID inputs to fixed levels internally, freeing the PB0 and PB1 pins for GPIO use. For proper self-powered Device operation, the VBUS value must still be monitored to assure that if the Host removes VBUS, the self-powered Device disables the D+/D- pull-up resistors. This function can be accomplished by connecting a standard GPIO to VBUS. USB General-Purpose Control and Status (USBGPCS) Base 0x4005.0000 Offset 0x41C Type R/W, reset 0x0000.0003 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 DEVMODOTG DEVMOD RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 1 R/W 1 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1 DEVMODOTG R/W 1 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Enable Device Mode This bit enables the DEVMOD bit to control the state of the internal ID signal in OTG mode. Value Description 0 DEVMOD R/W 1 0 The mode is specified by the state of the internal ID signal. 1 This bit enables the DEVMOD bit to control the internal ID signal. Device Mode This bit specifies the state of the internal ID signal in Host mode and in OTG mode when the DEVMODOTG bit is set. In Device mode this bit is ignored (assumed set). Value Description 0 Host mode 1 Device mode 1228 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 173: USB VBUS Droop Control (USBVDC), offset 0x430 OTG A / Host This 32-bit register enables a controlled masking of VBUS to compensate for any in-rush current by a Device that is connected to the Host controller. The in-rush current can cause VBUS to droop, causing the USB controller's behavior to be unexpected. The USB Host controller allows VBUS to fall lower than the VBUS Valid level (4.75 V) but not below AValid (2.0 V) for 65 microseconds without signaling a VBUSERR interrupt in the controller. Without this, any glitch on VBUS would force the USB Host controller to remove power from VBUS and then re-enumerate the Device. USB VBUS Droop Control (USBVDC) Base 0x4005.0000 Offset 0x430 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 VBDEN R/W 0 RO 0 VBDEN R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. VBUS Droop Enable Value Description 0 No effect. 1 Any changes from VBUSVALID are masked when VBUS goes below 4.75 V but not lower than 2.0 V for 65 microseconds. During this time, the VBUS state indicates VBUSVALID. November 08, 2011 1229 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 174: USB VBUS Droop Control Raw Interrupt Status (USBVDCRIS), offset 0x434 OTG A / Host This 32-bit register specifies the unmasked interrupt status of the VBUS droop limit of 65 microseconds. USB VBUS Droop Control Raw Interrupt Status (USBVDCRIS) Base 0x4005.0000 Offset 0x434 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 VD RO 0 RO 0 0 VD RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. VBUS Droop Raw Interrupt Status Value Description 1 A VBUS droop lasting for 65 microseconds has been detected. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the VD bit in the USBVDCISC register. 1230 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 175: USB VBUS Droop Control Interrupt Mask (USBVDCIM), offset 0x438 OTG A / This 32-bit register specifies the interrupt mask of the VBUS droop. USB VBUS Droop Control Interrupt Mask (USBVDCIM) Host Base 0x4005.0000 Offset 0x438 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 VD R/W 0 RO 0 0 VD RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. VBUS Droop Interrupt Mask Value Description 1 The raw interrupt signal from a detected VBUS droop is sent to the interrupt controller. 0 A detected VBUS droop does not affect the interrupt status. November 08, 2011 1231 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 176: USB VBUS Droop Control Interrupt Status and Clear (USBVDCISC), offset 0x43C OTG A / Host This 32-bit register specifies the masked interrupt status of the VBUS droop and provides a method to clear the interrupt state. USB VBUS Droop Control Interrupt Status and Clear (USBVDCISC) Base 0x4005.0000 Offset 0x43C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 VD R/W1C 0 RO 0 0 VD RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. VBUS Droop Interrupt Status and Clear Value Description 1 The VD bits in the USBVDCRIS and USBVDCIM registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the VD bit in the USBVDCRIS register. 1232 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 177: USB ID Valid Detect Raw Interrupt Status (USBIDVRIS), offset 0x444 This 32-bit register specifies whether the unmasked interrupt status of the ID value is valid. OTG USB ID Valid Detect Raw Interrupt Status (USBIDVRIS) Base 0x4005.0000 Offset 0x444 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 ID RO 0 RO 0 0 ID RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. ID Valid Detect Raw Interrupt Status Value Description 1 A valid ID has been detected. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the ID bit in the USBIDVISC register. November 08, 2011 1233 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 178: USB ID Valid Detect Interrupt Mask (USBIDVIM), offset 0x448 This 32-bit register specifies the interrupt mask of the ID valid detection. OTG USB ID Valid Detect Interrupt Mask (USBIDVIM) Base 0x4005.0000 Offset 0x448 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 ID R/W 0 RO 0 ID Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. ID Valid Detect Interrupt Mask Value Description 1 The raw interrupt signal from a detected ID valid is sent to the interrupt controller. 0 A detected ID valid does not affect the interrupt status. 1234 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 179: USB ID Valid Detect Interrupt Status and Clear (USBIDVISC), offset 0x44C This 32-bit register specifies the masked interrupt status of the ID valid detect. It also provides a method to clear the interrupt state. OTG USB ID Valid Detect Interrupt Status and Clear (USBIDVISC) Base 0x4005.0000 Offset 0x44C Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 ID R/W1C 0 RO 0 0 ID RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. ID Valid Detect Interrupt Status and Clear Value Description 1 The ID bits in the USBIDVRIS and USBIDVIM registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the ID bit in the USBIDVRIS register. November 08, 2011 1235 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 180: USB DMA Select (USBDMASEL), offset 0x450 OTG A / Host OTG B / This 32-bit register specifies which endpoints are mapped to the 6 allocated µDMA channels, see Table 9-1 on page 612 for more information on channel assignments. USB DMA Select (USBDMASEL) Base 0x4005.0000 Offset 0x450 Type R/W, reset 0x0033.2211 Device 31 30 29 28 RO 0 RO 0 RO 0 RO 0 15 14 13 R/W 0 R/W 0 27 26 25 24 23 22 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 12 11 10 9 8 7 6 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset R/W 1 20 19 18 R/W 1 R/W 1 R/W 0 R/W 0 R/W 1 R/W 1 5 4 3 2 1 0 R/W 1 R/W 0 R/W 0 DMACTX DMABTX Type Reset 21 DMABRX R/W 1 16 DMACRX DMAATX R/W 0 17 DMAARX R/W 0 R/W 1 Bit/Field Name Type Reset Description 31:24 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23:20 DMACTX R/W 0x3 DMA C TX Select Specifies the TX mapping of the third USB endpoint on µDMA channel 5 (primary assignment). Value Description 0x0 reserved 0x1 Endpoint 1 TX 0x2 Endpoint 2 TX 0x3 Endpoint 3 TX 0x4 Endpoint 4 TX 0x5 Endpoint 5 TX 0x6 Endpoint 6 TX 0x7 Endpoint 7 TX 0x8 - 0xF reserved 1236 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 19:16 DMACRX R/W 0x3 Description DMA C RX Select Specifies the RX and TX mapping of the third USB endpoint on µDMA channel 4 (primary assignment). Value Description 0x0 reserved 0x1 Endpoint 1 RX 0x2 Endpoint 2 RX 0x3 Endpoint 3 RX 0x4 Endpoint 4 RX 0x5 Endpoint 5 RX 0x6 Endpoint 6 RX 0x7 Endpoint 7 RX 0x8 - 0xF reserved 15:12 DMABTX R/W 0x2 DMA B TX Select Specifies the TX mapping of the second USB endpoint on µDMA channel 3 (primary assignment). Same bit definitions as the DMACTX field. 11:8 DMABRX R/W 0x2 DMA B RX Select Specifies the RX mapping of the second USB endpoint on µDMA channel 2 (primary assignment). Same bit definitions as the DMACRX field. 7:4 DMAATX R/W 0x1 DMA A TX Select Specifies the TX mapping of the first USB endpoint on µDMA channel 1 (primary assignment). Same bit definitions as the DMACTX field. 3:0 DMAARX R/W 0x1 DMA A RX Select Specifies the RX mapping of the first USB endpoint on µDMA channel 0 (primary assignment). Same bit definitions as the DMACRX field. November 08, 2011 1237 Texas Instruments-Advance Information Universal Serial Bus (USB) Controller Register 181: USB Peripheral Properties (USBPP), offset 0xFC0 The USBPP register provides information regarding the properties of the USB module. USB Peripheral Properties (USBPP) Base 0x4005.0000 Offset 0xFC0 Type RO, reset 0x0000.08D0 31 30 29 28 27 26 25 24 0 0 0 0 0 0 0 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 0 23 22 21 20 19 18 17 16 0 0 0 0 0 0 0 0 8 7 6 5 4 3 2 1 0 reserved PHY RO 0 RO 1 RO 0 RO 1 RO 0 RO 0 RO 0 RO 0 reserved Type Reset ECNT Type Reset USB RO 1 TYPE Bit/Field Name Type Reset Description 31:16 reserved - 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:8 ECNT RO 0x8 Endpoint Count This field encodes the number of endpoints provided 7:6 USB RO 0x3 USB Capability Value Description 0x0 NA USB is not present. 0x1 DEVICE Device Only 0x2 HOST Device or Host 0x3 OTG Device, Host, or OTG 5 reserved RO 0 4 PHY RO 0x1 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. PHY Present Value Description 3:0 TYPE RO 0x0 1 A PHY is integrated with the USB MAC. 0 A PHY is not integrated with the USB MAC. Controller Type Value Description 0x0 The first-generation USB controller. 0x1 - 0xF Reserved 1238 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 19 Analog Comparators An analog comparator is a peripheral that compares two analog voltages and provides a logical output that signals the comparison result. Note: Not all comparators have the option to drive an output pin. See “Signal Description” on page 1240 for more information. The comparator can provide its output to a device pin, acting as a replacement for an analog comparator on the board. In addition, the comparator can signal the application via interrupts or trigger the start of a sample sequence in the ADC. The interrupt generation and ADC triggering logic is separate and independent. This flexibility means, for example, that an interrupt can be generated on a rising edge and the ADC triggered on a falling edge. ® The Stellaris LM4F232H5BB microcontroller provides three independent integrated analog comparators with the following functions: ■ Compare external pin input to external pin input or to internal programmable voltage reference ■ Compare a test voltage against any one of the following voltages: – An individual external reference voltage – A shared single external reference voltage – A shared internal reference voltage November 08, 2011 1239 Texas Instruments-Advance Information Analog Comparators 19.1 Block Diagram Figure 19-1. Analog Comparator Module Block Diagram C2- -ve input C2+ +ve input Comparator 2 output +ve input (alternate) ACCTL2 trigger ACSTAT2 C2o trigger interrupt reference input C1- -ve input C1+ +ve input Comparator 1 output C1o +ve input (alternate) ACCTL1 trigger trigger ACSTAT1 interrupt reference input C0- -ve input C0+ +ve input Comparator 0 output C0o +ve input (alternate) ACCTL0 trigger ACSTAT0 trigger interrupt reference input Voltage Ref Interrupt Control ACRIS Internal Bus Interrupt ACREFCTL ACMIS ACINTEN Module Status ACMPPP 19.2 Signal Description The following table lists the external signals of the Analog Comparators and describes the function of each. The Analog Comparator output signals are alternate functions for some GPIO signals and default to be GPIO signals at reset. The column in the table below titled "Pin Mux/Pin Assignment" lists the possible GPIO pin placements for the Analog Comparator signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 698) should be set to choose the Analog Comparator function. The number in parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control (GPIOPCTL) register (page 717) to assign the Analog Comparator signal to the specified GPIO port pin. The positive and negative input signals are configured by clearing the DEN bit in the GPIO Digital Enable (GPIODEN) register. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 674. Table 19-1. Analog Comparators Signals (157BGA) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description C0+ K1 PC6 I Analog Analog comparator 0 positive input. C0- K2 PC7 I Analog Analog comparator 0 negative input. C0o M9 B11 PF0 (9) PK4 (8) O TTL Analog comparator 0 output. 1240 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 19-1. Analog Comparators Signals (157BGA) (continued) Pin Name Pin Number Pin Mux / Pin Assignment L1 C1+ PC5 a Pin Type Buffer Type Description I Analog Analog comparator 1 positive input. Analog comparator 1 negative input. C1- L2 PC4 I Analog C1o N9 B12 PF1 (9) PK5 (8) O TTL C2+ D5 PJ4 I Analog Analog comparator 2 positive input. C2- C5 PJ5 I Analog Analog comparator 2 negative input. C2o L10 C11 PF2 (9) PK6 (8) O TTL Analog comparator 1 output. Analog comparator 2 output. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 19.3 Functional Description The comparator compares the VIN- and VIN+ inputs to produce an output, VOUT. VIN- < VIN+, VOUT = 1 VIN- > VIN+, VOUT = 0 As shown in Figure 19-2 on page 1241, the input source for VIN- is an external input, Cn-. In addition to an external input, Cn+, input sources for VIN+ can be the C0+ or an internal reference, VIREF. Figure 19-2. Structure of Comparator Unit - ve input + ve input (alternate) reference input 0 output CINV 1 IntGen 2 TrigGen internal bus ACCTL ACSTAT trigger interrupt + ve input A comparator is configured through two status/control registers, Analog Comparator Control (ACCTL) and Analog Comparator Status (ACSTAT). The internal reference is configured through one control register, Analog Comparator Reference Voltage Control (ACREFCTL). Interrupt status and control are configured through three registers, Analog Comparator Masked Interrupt Status (ACMIS), Analog Comparator Raw Interrupt Status (ACRIS), and Analog Comparator Interrupt Enable (ACINTEN). Typically, the comparator output is used internally to generate an interrupt as controlled by the ISEN bit in the ACCTL register. The output may also be used to drive an external pin, Co or generate an analog-to-digital converter (ADC) trigger. Important: The ASRCP bits in the ACCTL register must be set before using the analog comparators. November 08, 2011 1241 Texas Instruments-Advance Information Analog Comparators 19.3.1 Internal Reference Programming The structure of the internal reference is shown in Figure 19-3 on page 1242. The internal reference is controlled by a single configuration register (ACREFCTL). Table 19-2 on page 1242 shows the programming options to develop specific internal reference values, to compare an external voltage against a particular voltage generated internally (VIREF). Figure 19-3. Comparator Internal Reference Structure Table 19-2. Internal Reference Voltage and ACREFCTL Field Values ACREFCTL Register EN Bit Value EN=0 RNG Bit Value Output Reference Voltage Based on VREF Field Value RNG=X 0 V (GND) for any value of VREF; however, it is recommended that RNG=1 and VREF=0 for the least noisy ground reference. 1242 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 19-2. Internal Reference Voltage and ACREFCTL Field Values (continued) ACREFCTL Register EN Bit Value RNG Bit Value Output Reference Voltage Based on VREF Field Value RNG=0 Total resistance in ladder is 29.23 R. VIREF = VDDA × VIREF = VDDA × V IREF EN=1 RNG=1 RVREF RT (VREF + 8) V DDA u 31 VREF  7 . 11  V = 0.85 +R0VREF .106 × 31 VREF IREF = VDDA × VIREF RVREF RT VIREF = VDDA × RVREF IREF = VDDA × RT0 . 1128 u VREF VV IREF 0 . 802 ( VREF + 8) RT VIREF = VDDA × (VREF 31 + 8) Vrange × VREF IREF = VDDAreference The in this mode is 0.802 - 2.494 V. VIREF of=internal VDDA × 31 Total resistance in. ladder is 22.11 R. VIREF = 0 85 + 023 .106 × VREF VIREF = 0.85 + 0.106 × VREF VIREF = 0.143 R ×VREF VREF VIREF = VDDA × RVREF VIREF = VDDA × RT RT VREF V IREF = VDDA × V IREF 0 . 149 u VREF VREF VIREF = VDDA × 23 23 VIREF = 0.143 × VREF VIREF = 0.143 × VREF The range of internal reference for this mode is 0-2.238 V. 19.4 Initialization and Configuration The following example shows how to configure an analog comparator to read back its output value from an internal register. 1. Enable the analog comparator clock by writing a value of 0x0000.0001 to the RCGCACMP register in the System Control module (see page 403). 2. Enable the clock to the appropriate GPIO modules via the RCGCGPIO register (see page 389). To find out which GPIO ports to enable, refer to Table 23-5 on page 1398. 3. In the GPIO module, enable the GPIO port/pin associated with the input signals as GPIO inputs. To determine which GPIO to configure, see Table 23-4 on page 1387. 4. Configure the PMCn fields in the GPIOPCTL register to assign the analog comparator output signals to the appropriate pins (see page 717 and Table 23-5 on page 1398). November 08, 2011 1243 Texas Instruments-Advance Information Analog Comparators 5. Configure the internal voltage reference to 1.65 V by writing the ACREFCTL register with the value 0x0000.030C. 6. Configure the comparator to use the internal voltage reference and to not invert the output by writing the ACCTLn register with the value of 0x0000.040C. 7. Delay for 10 µs. 8. Read the comparator output value by reading the ACSTATn register’s OVAL value. Change the level of the comparator negative input signal C- to see the OVAL value change. 19.5 Register Map Table 19-3 on page 1244 lists the comparator registers. The offset listed is a hexadecimal increment to the register’s address, relative to the Analog Comparator base address of 0x4003.C000. Note that the analog comparator clock must be enabled before the registers can be programmed (see page 403). There must be a delay of 3 system clocks after the analog comparator module clock is enabled before any analog comparator module registers are accessed. Table 19-3. Analog Comparators Register Map Description See page 0x0000.0000 Analog Comparator Masked Interrupt Status 1245 RO 0x0000.0000 Analog Comparator Raw Interrupt Status 1246 ACINTEN R/W 0x0000.0000 Analog Comparator Interrupt Enable 1247 0x010 ACREFCTL R/W 0x0000.0000 Analog Comparator Reference Voltage Control 1248 0x020 ACSTAT0 RO 0x0000.0000 Analog Comparator Status 0 1249 0x024 ACCTL0 R/W 0x0000.0000 Analog Comparator Control 0 1250 0x040 ACSTAT1 RO 0x0000.0000 Analog Comparator Status 1 1249 0x044 ACCTL1 R/W 0x0000.0000 Analog Comparator Control 1 1250 0x060 ACSTAT2 RO 0x0000.0000 Analog Comparator Status 2 1249 0x064 ACCTL2 R/W 0x0000.0000 Analog Comparator Control 2 1250 0xFC0 ACMPPP RO 0x0007.0007 Analog Comparator Peripheral Properties 1252 Offset Name Type Reset 0x000 ACMIS R/W1C 0x004 ACRIS 0x008 19.6 Register Descriptions The remainder of this section lists and describes the Analog Comparator registers, in numerical order by address offset. 1244 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 1: Analog Comparator Masked Interrupt Status (ACMIS), offset 0x000 This register provides a summary of the interrupt status (masked) of the comparators. Analog Comparator Masked Interrupt Status (ACMIS) Base 0x4003.C000 Offset 0x000 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 IN2 IN1 IN0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:3 reserved RO 0x0000.000 2 IN2 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Comparator 2 Masked Interrupt Status Value Description 1 The IN2 bits in the ACRIS register and the ACINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the IN2 bit in the ACRIS register. 1 IN1 R/W1C 0 Comparator 1 Masked Interrupt Status Value Description 1 The IN1 bits in the ACRIS register and the ACINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the IN1 bit in the ACRIS register. 0 IN0 R/W1C 0 Comparator 0 Masked Interrupt Status Value Description 1 The IN0 bits in the ACRIS register and the ACINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the IN0 bit in the ACRIS register. November 08, 2011 1245 Texas Instruments-Advance Information Analog Comparators Register 2: Analog Comparator Raw Interrupt Status (ACRIS), offset 0x004 This register provides a summary of the interrupt status (raw) of the comparators. The bits in this register must be enabled to generate interrupts using the ACINTEN register. Analog Comparator Raw Interrupt Status (ACRIS) Base 0x4003.C000 Offset 0x004 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 IN2 IN1 IN0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:3 reserved RO 0x0000.000 2 IN2 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Comparator 2 Interrupt Status Value Description 1 Comparator 2 has generated an interrupt for an event as configured by the ISEN bit in the ACCTL2 register. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the IN2 bit in the ACMIS register. 1 IN1 RO 0 Comparator 1 Interrupt Status Value Description 1 Comparator 1 has generated an interruptfor an event as configured by the ISEN bit in the ACCTL1 register. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the IN1 bit in the ACMIS register. 0 IN0 RO 0 Comparator 0 Interrupt Status Value Description 1 Comparator 0 has generated an interrupt for an event as configured by the ISEN bit in the ACCTL0 register. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the IN0 bit in the ACMIS register. 1246 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 3: Analog Comparator Interrupt Enable (ACINTEN), offset 0x008 This register provides the interrupt enable for the comparators. Analog Comparator Interrupt Enable (ACINTEN) Base 0x4003.C000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 IN2 IN1 IN0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 IN2 R/W 0 Comparator 2 Interrupt Enable Value Description 1 IN1 R/W 0 1 The raw interrupt signal comparator 2 is sent to the interrupt controller. 0 A comparator 2 interrupt does not affect the interrupt status. Comparator 1 Interrupt Enable Value Description 0 IN0 R/W 0 1 The raw interrupt signal comparator 1 is sent to the interrupt controller. 0 A comparator 1 interrupt does not affect the interrupt status. Comparator 0 Interrupt Enable Value Description 1 The raw interrupt signal comparator 0 is sent to the interrupt controller. 0 A comparator 0 interrupt does not affect the interrupt status. November 08, 2011 1247 Texas Instruments-Advance Information Analog Comparators Register 4: Analog Comparator Reference Voltage Control (ACREFCTL), offset 0x010 This register specifies whether the resistor ladder is powered on as well as the range and tap. Analog Comparator Reference Voltage Control (ACREFCTL) Base 0x4003.C000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 1 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 9 8 EN RNG R/W 0 R/W 0 Bit/Field Name Type Reset 31:10 reserved RO 0x0000.0 9 EN R/W 0 reserved RO 0 RO 0 RO 0 VREF RO 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Resistor Ladder Enable Value Description 0 The resistor ladder is unpowered. 1 Powers on the resistor ladder. The resistor ladder is connected to VDDA. This bit is cleared at reset so that the internal reference consumes the least amount of power if it is not used. 8 RNG R/W 0 Resistor Ladder Range Value Description 0 The resistor ladder has a total resistance of 29.23 R. 1 The resistor ladder has a total resistance of 22.11 R. 7:4 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3:0 VREF R/W 0x0 Resistor Ladder Voltage Ref The VREF bit field specifies the resistor ladder tap that is passed through an analog multiplexer. The voltage corresponding to the tap position is the internal reference voltage available for comparison. See Table 19-2 on page 1242 for some output reference voltage examples. 1248 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 5: Analog Comparator Status 0 (ACSTAT0), offset 0x020 Register 6: Analog Comparator Status 1 (ACSTAT1), offset 0x040 Register 7: Analog Comparator Status 2 (ACSTAT2), offset 0x060 These registers specify the current output value of the comparator. Analog Comparator Status 0 (ACSTAT0) Base 0x4003.C000 Offset 0x020 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 OVAL reserved RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1 OVAL RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Comparator Output Value Value Description 0 VIN- > VIN+ 1 VIN- < VIN+ VIN - is the voltage on the Cn- pin. VIN+ is the voltage on the Cn+ pin, the C0+ pin, or the internal voltage reference (VIREF) as defined by the ASRCP bit in the ACCTL register. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1249 Texas Instruments-Advance Information Analog Comparators Register 8: Analog Comparator Control 0 (ACCTL0), offset 0x024 Register 9: Analog Comparator Control 1 (ACCTL1), offset 0x044 Register 10: Analog Comparator Control 2 (ACCTL2), offset 0x064 These registers configure the comparator’s input and output. Analog Comparator Control 0 (ACCTL0) Base 0x4003.C000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 reserved TSLVAL CINV reserved RO 0 R/W 0 R/W 0 RO 0 reserved Type Reset reserved Type Reset TOEN RO 0 RO 0 ASRCP R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:12 reserved RO 0x0000.0 11 TOEN R/W 0 TSEN R/W 0 ISLVAL R/W 0 R/W 0 ISEN R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Trigger Output Enable Value Description 10:9 ASRCP R/W 0x0 0 ADC events are suppressed and not sent to the ADC. 1 ADC events are sent to the ADC. Analog Source Positive The ASRCP field specifies the source of input voltage to the VIN+ terminal of the comparator. The encodings for this field are as follows: Value Description 0x0 Pin value of Cn+ 0x1 Pin value of C0+ 0x2 Internal voltage reference (VIREF) 0x3 Reserved 8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 TSLVAL R/W 0 Trigger Sense Level Value Value Description 0 An ADC event is generated if the comparator output is Low. 1 An ADC event is generated if the comparator output is High. 1250 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 6:5 TSEN R/W 0x0 Description Trigger Sense The TSEN field specifies the sense of the comparator output that generates an ADC event. The sense conditioning is as follows: Value Description 4 ISLVAL R/W 0 0x0 Level sense, see TSLVAL 0x1 Falling edge 0x2 Rising edge 0x3 Either edge Interrupt Sense Level Value Value Description 3:2 ISEN R/W 0x0 0 An interrupt is generated if the comparator output is Low. 1 An interrupt is generated if the comparator output is High. Interrupt Sense The ISEN field specifies the sense of the comparator output that generates an interrupt. The sense conditioning is as follows: Value Description 1 CINV R/W 0 0x0 Level sense, see ISLVAL 0x1 Falling edge 0x2 Rising edge 0x3 Either edge Comparator Output Invert Value Description 0 reserved RO 0 0 The output of the comparator is unchanged. 1 The output of the comparator is inverted prior to being processed by hardware. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1251 Texas Instruments-Advance Information Analog Comparators Register 11: Analog Comparator Peripheral Properties (ACMPPP), offset 0xFC0 The ACMPPP register provides information regarding the properties of the analog comparator module. Analog Comparator Peripheral Properties (ACMPPP) Base 0x4003.C000 Offset 0xFC0 Type RO, reset 0x0007.0007 31 30 29 28 27 26 0 0 0 0 0 0 15 14 13 12 11 10 0 0 0 0 0 0 25 24 23 22 21 20 19 0 0 0 0 0 0 0 9 8 7 6 5 4 3 0 0 0 0 0 0 reserved Type Reset reserved Type Reset 0 18 17 16 C2O C1O C0O RO 1 RO 1 RO 1 2 1 0 CMP2 CMP1 CMP0 RO 1 RO 1 RO 1 Bit/Field Name Type Reset Description 31:19 reserved - 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 18 C2O RO 0x1 Comparator Output 2 Present Value Description 17 C1O RO 0x1 1 Comparator output 2 is present. 0 Comparator output 2 is not present. Comparator Output 1 Present Value Description 16 C0O RO 0x1 1 Comparator output 1 is present. 0 Comparator output 1 is not present. Comparator Output 0 Present Value Description 1 Comparator output 0 is present. 0 Comparator output 0 is not present. 15:3 reserved - 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 CMP2 RO 0x1 Comparator 2 Present Value Description 1 Comparator 2 is present. 0 Comparator 2 is not present. 1252 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1 CMP1 RO 0x1 Description Comparator 1 Present Value Description 0 CMP0 RO 0x1 1 Comparator 1 is present. 0 Comparator 1 is not present. Comparator 0 Present Value Description 1 Comparator 0 is present. 0 Comparator 0 is not present. November 08, 2011 1253 Texas Instruments-Advance Information Pulse Width Modulator (PWM) 20 Pulse Width Modulator (PWM) Pulse width modulation (PWM) is a powerful technique for digitally encoding analog signal levels. High-resolution counters are used to generate a square wave, and the duty cycle of the square wave is modulated to encode an analog signal. Typical applications include switching power supplies and motor control. ® The Stellaris microcontroller contains two PWM modules, each with four PWM generator blocks and a control block, for a total of 16 PWM outputs. The control block determines the polarity of the PWM signals, and which signals are passed through to the pins. Each PWM generator block produces two PWM signals that share the same timer and frequency and can either be programmed with independent actions or as a single pair of complementary signals with dead-band delays inserted. The output signals, pwmA' and pwmB', of the PWM generation blocks are managed by the output control block before being passed to the device pins as MnPWM0 and MnPWM1 or MnPWM2 and MnPWM3, and so on. Each Stellaris PWM module provides a great deal of flexibility and can generate simple PWM signals, such as those required by a simple charge pump as well as paired PWM signals with dead-band delays, such as those required by a half-H bridge driver. Three generator blocks can also generate the full six channels of gate controls required by a 3-phase inverter bridge. Each PWM generator block has the following features: ■ Four fault-condition handling inputs to quickly provide low-latency shutdown and prevent damage to the motor being controlled, for a total of eight inputs ■ One 16-bit counter – Runs in Down or Up/Down mode – Output frequency controlled by a 16-bit load value – Load value updates can be synchronized – Produces output signals at zero and load value ■ Two PWM comparators – Comparator value updates can be synchronized – Produces output signals on match ■ PWM signal generator – Output PWM signal is constructed based on actions taken as a result of the counter and PWM comparator output signals – Produces two independent PWM signals ■ Dead-band generator – Produces two PWM signals with programmable dead-band delays suitable for driving a half-H bridge – Can be bypassed, leaving input PWM signals unmodified 1254 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Can initiate an ADC sample sequence The control block determines the polarity of the PWM signals and which signals are passed through to the pins. The output of the PWM generation blocks are managed by the output control block before being passed to the device pins. The PWM control block has the following options: ■ PWM output enable of each PWM signal ■ Optional output inversion of each PWM signal (polarity control) ■ Optional fault handling for each PWM signal ■ Synchronization of timers in the PWM generator blocks ■ Synchronization of timer/comparator updates across the PWM generator blocks ■ Extended PWM synchronization of timer/comparator updates across the PWM generator blocks ■ Interrupt status summary of the PWM generator blocks ■ Extended PWM fault handling, with multiple fault signals, programmable polarities, and filtering ■ PWM generators can be operated independently or synchronized with other generators 20.1 Block Diagram Figure 20-1 on page 1256 provides the Stellaris PWM module diagram and Figure 20-2 on page 1256 provides a more detailed diagram of a Stellaris PWM generator. The LM4F232H5BB controller contains two PWM modules, each with four generator blocks that generate eight independent PWM signals or four paired PWM signals with dead-band delays inserted. November 08, 2011 1255 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Figure 20-1. PWM Module Diagram PWM Clock pwm0A’ Triggers / Faults System Clock PWM Generator 0 Control and Status PWMCTL PWMSYNC PWMSTATUS PWM 0 pwm0B’ PWM 1 pwm0fault pwm1A’ PWM Generator 1 PWM 2 pwm1B’ PWM PWM 3 pwm1fault Output Interrupt pwm2A’ Interrupts PWMINTEN PWMRIS PWMISC PWM Generator 2 Output PWM Generator 3 pwm2B’ Control PWM 4 Logic PWM 5 pwm2fault Triggers pwm3A’ PWMENABLE PWMINVERT PWMFAULT PWMFAULTVAL PWMENUPD PWM 6 pwm3B’ PWM 7 pwm3fault Figure 20-2. PWM Generator Block Diagram PWM Generator Block Interrupts / Triggers Control PWMnLOAD PWMnCOUNT PWMnFLTSRC0 PWMnFLTSRC1 PWMnMINFLTPER PWMnFLTSEN PWMnFLTSTAT0 PWMnFLTSTAT1 PWMnINTEN PWMnRIS PWMnISC PWMnCTL Timer Fault Condition Interrupt and Trigger Generator load dir pwmfault Signal Generator pwmA pwmB PWM Clock 20.2 Fault(s) zero Comparators PWMnCMPA PWMnCMPB Digital Trigger(s) cmpA cmpB PWMnGENA PWMnGENB Dead-Band Generator PWMnDBCTL PWMnDBRISE PWMnDBFALL pwmA’ pwmB’ Signal Description The following table lists the external signals of the PWM modules and describes the function of each. The PWM controller signals are alternate functions for some GPIO signals and default to be 1256 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller GPIO signals at reset. The column in the table below titled "Pin Mux/Pin Assignment" lists the possible GPIO pin placements for these PWM signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 698) should be set to choose the PWM function. The number in parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control (GPIOPCTL) register (page 717) to assign the PWM signal to the specified GPIO port pin. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 674. Table 20-1. PWM Signals (157BGA) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description M0FAULT0 C2 A3 L10 K3 B11 PD2 (4) PD6 (4) PF2 (4) PH0 (6) PK4 (6) I TTL Motion Control Module 0 PWM Fault 0. M0FAULT1 B3 K10 N7 K4 B12 PD7 (4) PF3 (4) PG2 (4) PH1 (6) PK5 (6) I TTL Motion Control Module 0 PWM Fault 1. M0FAULT2 L9 M7 J4 C11 PF4 (4) PG3 (4) PH2 (6) PK6 (6) I TTL Motion Control Module 0 PWM Fault 2. M0FAULT3 K9 J2 A12 PF5 (4) PH3 (6) PK7 (6) I TTL Motion Control Module 0 PWM Fault 3. M0PWM0 F4 K3 M13 PB6 (4) PH0 (4) PP0 (1) O TTL Motion Control Module 0 PWM 0. This signal is controlled by Module 0 PWM Generator 0. M0PWM1 F3 K4 L12 PB7 (4) PH1 (4) PP1 (1) O TTL Motion Control Module 0 PWM 1. This signal is controlled by Module 0 PWM Generator 0. M0PWM2 B6 J4 M5 PB4 (4) PH2 (4) PP2 (1) O TTL Motion Control Module 0 PWM 2. This signal is controlled by Module 0 PWM Generator 1. M0PWM3 A6 J2 J12 PB5 (4) PH3 (4) PP3 (1) O TTL Motion Control Module 0 PWM 3. This signal is controlled by Module 0 PWM Generator 1. M0PWM4 A5 K7 J3 H11 J13 PE4 (4) PG4 (4) PH4 (4) PM6 (2) PP4 (1) O TTL Motion Control Module 0 PWM 4. This signal is controlled by Module 0 PWM Generator 2. M0PWM5 B5 L7 H4 L13 L5 PE5 (4) PG5 (4) PH5 (4) PM7 (2) PP5 (1) O TTL Motion Control Module 0 PWM 5. This signal is controlled by Module 0 PWM Generator 2. November 08, 2011 1257 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Table 20-1. PWM Signals (157BGA) (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description M0PWM6 L2 B2 N4 H3 G3 D8 PC4 (4) PD0 (4) PG6 (4) PH6 (4) PN2 (2) PP6 (1) O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. M0PWM7 L1 B1 N3 G4 D10 K6 PC5 (4) PD1 (4) PG7 (4) PH7 (4) PN3 (2) PP7 (1) O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. M1FAULT0 L9 M8 G2 PF4 (5) PF7 (5) PK0 (6) I TTL Motion Control Module 1 PWM Fault 0. M1FAULT1 L8 G1 PG0 (5) PK1 (6) I TTL Motion Control Module 1 PWM Fault 1. M1FAULT2 K8 H1 PG1 (5) PK2 (6) I TTL Motion Control Module 1 PWM Fault 2. M1FAULT3 H2 PK3 (6) I TTL Motion Control Module 1 PWM Fault 3. M1PWM0 B2 N7 D4 PD0 (5) PG2 (5) PQ0 (1) O TTL Motion Control Module 1 PWM 0. This signal is controlled by Module 1 PWM Generator 0. M1PWM1 B1 M7 E4 PD1 (5) PG3 (5) PQ1 (1) O TTL Motion Control Module 1 PWM 1. This signal is controlled by Module 1 PWM Generator 0. M1PWM2 M4 A5 K7 F5 PA6 (5) PE4 (5) PG4 (5) PQ2 (1) O TTL Motion Control Module 1 PWM 2. This signal is controlled by Module 1 PWM Generator 1. M1PWM3 N2 B5 L7 N5 PA7 (5) PE5 (5) PG5 (5) PQ3 (1) O TTL Motion Control Module 1 PWM 3. This signal is controlled by Module 1 PWM Generator 1. M1PWM4 M9 L11 N6 PF0 (5) PN4 (2) PQ4 (1) O TTL Motion Control Module 1 PWM 4. This signal is controlled by Module 1 PWM Generator 2. M1PWM5 N9 N12 K5 PF1 (5) PN5 (2) PQ5 (1) O TTL Motion Control Module 1 PWM 5. This signal is controlled by Module 1 PWM Generator 2. M1PWM6 L10 N11 M6 PF2 (5) PN6 (2) PQ6 (1) O TTL Motion Control Module 1 PWM 6. This signal is controlled by Module 1 PWM Generator 3. M1PWM7 K10 M11 L6 PF3 (5) PN7 (2) PQ7 (1) O TTL Motion Control Module 1 PWM 7. This signal is controlled by Module 1 PWM Generator 3. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 1258 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 20.3 Functional Description 20.3.1 PWM Timer The timer in each PWM generator runs in one of two modes: Count-Down mode or Count-Up/Down mode. In Count-Down mode, the timer counts from the load value to zero, goes back to the load value, and continues counting down. In Count-Up/Down mode, the timer counts from zero up to the load value, back down to zero, back up to the load value, and so on. Generally, Count-Down mode is used for generating left- or right-aligned PWM signals, while the Count-Up/Down mode is used for generating center-aligned PWM signals. The timers output three signals that are used in the PWM generation process: the direction signal (this is always Low in Count-Down mode, but alternates between Low and High in Count-Up/Down mode), a single-clock-cycle-width High pulse when the counter is zero, and a single-clock-cycle-width High pulse when the counter is equal to the load value. Note that in Count-Down mode, the zero pulse is immediately followed by the load pulse. In the figures in this chapter, these signals are labelled "dir," "zero," and "load." 20.3.2 PWM Comparators Each PWM generator has two comparators that monitor the value of the counter; when either comparator matches the counter, they output a single-clock-cycle-width High pulse, labelled "cmpA" and "cmpB" in the figures in this chapter. When in Count-Up/Down mode, these comparators match both when counting up and when counting down, and thus are qualified by the counter direction signal. These qualified pulses are used in the PWM generation process. If either comparator match value is greater than the counter load value, then that comparator never outputs a High pulse. Figure 20-3 on page 1260 shows the behavior of the counter and the relationship of these pulses when the counter is in Count-Down mode. Figure 20-4 on page 1260 shows the behavior of the counter and the relationship of these pulses when the counter is in Count-Up/Down mode. In these figures, the following definitions apply: ■ LOAD is the value in the PWMnLOAD register ■ COMPA is the value in the PWMnCMPA register ■ COMPB is the value in the PWMnCMPB register ■ 0 is the value zero ■ load is the internal signal that has a single-clock-cycle-width High pulse when the counter is equal to the load value ■ zero is the internal signal that has a single-clock-cycle-width High pulse when the counter is zero ■ cmpA is the internal signal that has a single-clock-cycle-width High pulse when the counter is equal to COMPA ■ cmpB is the internal signal that has a single-clock-cycle-width High pulse when the counter is equal to COMPB ■ dir is the internal signal that indicates the count direction November 08, 2011 1259 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Figure 20-3. PWM Count-Down Mode LOAD COMPA COMPB 0 load zero cmpA cmpB dir BDown ADown Figure 20-4. PWM Count-Up/Down Mode LOAD COMPA COMPB 0 load zero cmpA cmpB dir BUp AUp 20.3.3 BDown ADown PWM Signal Generator Each PWM generator takes the load, zero, cmpA, and cmpB pulses (qualified by the dir signal) and generates two internal PWM signals, pwmA and pwmB. In Count-Down mode, there are four events that can affect these signals: zero, load, match A down, and match B down. In Count-Up/Down mode, there are six events that can affect these signals: zero, load, match A down, match A up, match B down, and match B up. The match A or match B events are ignored when they coincide with the zero or load events. If the match A and match B events coincide, the first signal, pwmA, is generated based only on the match A event, and the second signal, pwmB, is generated based only on the match B event. For each event, the effect on each output PWM signal is programmable: it can be left alone (ignoring the event), it can be toggled, it can be driven Low, or it can be driven High. These actions can be used to generate a pair of PWM signals of various positions and duty cycles, which do or do not overlap. Figure 20-5 on page 1261 shows the use of Count-Up/Down mode to generate a pair of 1260 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller center-aligned, overlapped PWM signals that have different duty cycles. This figure shows the pwmA and pwmB signals before they have passed through the dead-band generator. Figure 20-5. PWM Generation Example In Count-Up/Down Mode LOAD COMPA COMPB 0 pwmA pwmB In this example, the first generator is set to drive High on match A up, drive Low on match A down, and ignore the other four events. The second generator is set to drive High on match B up, drive Low on match B down, and ignore the other four events. Changing the value of comparator A changes the duty cycle of the pwmA signal, and changing the value of comparator B changes the duty cycle of the pwmB signal. 20.3.4 Dead-Band Generator The pwmA and pwmB signals produced by each PWM generator are passed to the dead-band generator. If the dead-band generator is disabled, the PWM signals simply pass through to the pwmA' and pwmB' signals unmodified. If the dead-band generator is enabled, the pwmB signal is lost and two PWM signals are generated based on the pwmA signal. The first output PWM signal, pwmA' is the pwmA signal with the rising edge delayed by a programmable amount. The second output PWM signal, pwmB', is the inversion of the pwmA signal with a programmable delay added between the falling edge of the pwmA signal and the rising edge of the pwmB' signal. The resulting signals are a pair of active High signals where one is always High, except for a programmable amount of time at transitions where both are Low. These signals are therefore suitable for driving a half-H bridge, with the dead-band delays preventing shoot-through current from damaging the power electronics. Figure 20-6 on page 1261 shows the effect of the dead-band generator on the pwmA signal and the resulting pwmA' and pwmB' signals that are transmitted to the output control block. Figure 20-6. PWM Dead-Band Generator pwmA pwmA’ pwmB’ Rising Edge Delay 20.3.5 Falling Edge Delay Interrupt/ADC-Trigger Selector Each PWM generator also takes the same four (or six) counter events and uses them to generate an interrupt or an ADC trigger. Any of these events or a set of these events can be selected as a source for an interrupt; when any of the selected events occur, an interrupt is generated. Additionally, the same event, a different event, the same set of events, or a different set of events can be selected as a source for an ADC trigger; when any of these selected events occur, an ADC trigger pulse is generated. The selection of events allows the interrupt or ADC trigger to occur at a specific position November 08, 2011 1261 Texas Instruments-Advance Information Pulse Width Modulator (PWM) within the pwmA or pwmB signal. Note that interrupts and ADC triggers are based on the raw events; delays in the PWM signal edges caused by the dead-band generator are not taken into account. 20.3.6 Synchronization Methods Each PWM module provides four PWM generators, each providing two PWM outputs that may be used in a wide variety of applications. Generally speaking, the PWM is used in one of two categories of operation: ■ Unsynchronized. The PWM generator and its two output signals are used alone, independent of other PWM generators. ■ Synchronized. The PWM generator and its two outputs signals are used in conjunction with other PWM generators using a common, unified time base. If multiple PWM generators are configured with the same counter load value, synchronization can be used to guarantee that they also have the same count value (the PWM generators must be configured before they are synchronized). With this feature, more than two MnPWMn signals can be produced with a known relationship between the edges of those signals because the counters always have the same values. Other states in the module provide mechanisms to maintain the common time base and mutual synchronization. The counter in a PWM generator can be reset to zero by writing the PWM Time Base Sync (PWMSYNC) register and setting the SYNCn bit associated with the generator. Multiple PWM generators can be synchronized together by setting all necessary SYNCn bits in one access. For example, setting the SYNC0 and SYNC1 bits in the PWMSYNC register causes the counters in PWM generators 0 and 1 to reset together. Additional synchronization can occur between multiple PWM generators by updating register contents in one of the following three ways: ■ Immediately. The write value has immediate effect, and the hardware reacts immediately. ■ Locally Synchronized. The write value does not affect the logic until the counter reaches the value zero at the end of the PWM cycle. In this case, the effect of the write is deferred, providing a guaranteed defined behavior and preventing overly short or overly long output PWM pulses. ■ Globally Synchronized. The write value does not affect the logic until two sequential events have occurred: (1) the Update mode for the generator function is programmed for global synchronization in the PWMnCTL register, and (2) the counter reaches zero at the end of the PWM cycle. In this case, the effect of the write is deferred until the end of the PWM cycle following the end of all updates. This mode allows multiple items in multiple PWM generators to be updated simultaneously without odd effects during the update; everything runs from the old values until a point at which they all run from the new values. The Update mode of the load and comparator match values can be individually configured in each PWM generator block. It typically makes sense to use the synchronous update mechanism across PWM generator blocks when the timers in those blocks are synchronized, although this is not required in order for this mechanism to function properly. The following registers provide either local or global synchronization based on the state of various Update mode bits and fields in the PWMnCTL register (LOADUPD; CMPAUPD; CMPBUPD): ■ Generator Registers: PWMnLOAD, PWMnCMPA, and PWMnCMPB The following registers default to immediate update, but are provided with the optional functionality of synchronously updating rather than having all updates take immediate effect: 1262 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Module-Level Register: PWMENABLE (based on the state of the ENUPDn bits in the PWMENUPD register). ■ Generator Register: PWMnGENA, PWMnGENB, PWMnDBCTL, PWMnDBRISE, and PWMnDBFALL (based on the state of various Update mode bits and fields in the PWMnCTL register (GENAUPD; GENBUPD; DBCTLUPD; DBRISEUPD; DBFALLUPD)). All other registers are considered statically provisioned for the execution of an application or are used dynamically for purposes unrelated to maintaining synchronization and therefore do not need synchronous update functionality. 20.3.7 Fault Conditions A fault condition is one in which the controller must be signaled to stop normal PWM function and then set the MnPWMn signals to a safe state. Two basic situations cause fault conditions: ■ The microcontroller is stalled and cannot perform the necessary computation in the time required for motion control ■ An external error or event is detected Each PWM generator can use the following inputs to generate a fault condition, including: ■ MnFAULTn pin assertion ■ A stall of the controller generated by the debugger ■ The trigger of an ADC digital comparator Fault conditions are calculated on a per-PWM generator basis. Each PWM generator configures the necessary conditions to indicate a fault condition exists. This method allows the development of applications with dependent and independent control. Eight fault input pins (MnFAULTn) are available. These inputs may be used with circuits that generate an active High or active Low signal to indicate an error condition. A MnFAULTn pins may be individually programmed for the appropriate logic sense using the PWMnFLTSEN register. The PWM generator's mode control, including fault condition handling, is provided in the PWMnCTL register. The PWMnCTL register also selects whether the fault condition is maintained as long as the external condition lasts or if it is latched until the fault condition until cleared by software. Finally, this register also enables a counter that may be used to extend the period of a fault condition for external events to assure that the duration is a minimum length. The minimum fault period count is specified in the PWMnMINFLTPER register. Status regarding the specific fault cause is provided in the PWMnFLTSTAT0 and PWMnFLTSTAT1 registers. PWM generator fault conditions may be promoted to a controller interrupt using the PWMINTEN register. 20.3.8 Output Control Block The output control block takes care of the final conditioning of the pwmA' and pwmB' signals before they go to the pins as the MnPWMn signals. Via a single register, the PWM Output Enable (PWNENABLE) register, the set of PWM signals that are actually enabled to the pins can be modified. This function can be used, for example, to perform commutation of a brushless DC motor with a single register write (and without modifying the individual PWM generators, which are modified by November 08, 2011 1263 Texas Instruments-Advance Information Pulse Width Modulator (PWM) the feedback control loop). In addition, the updating of the bits in the PWMENABLE register can be configured to be immediate or locally or globally synchronized to the next synchronous update using the PWM Enable Update (PWMENUPD) register. During fault conditions, the PWM output signals, MnPWMn, usually must be driven to safe values so that external equipment may be safely controlled. The PWMFAULT register specifies whether during a fault condition, the generated signal continues to be passed driven or to an encoding specified in the PWMFAULTVAL register. A final inversion can be applied to any of the MnPWMn signals, making them active Low instead of the default active High using the PWM Output Inversion (PWMINVERT). The inversion is applied even if a value has been enabled in the PWMFAULT register and specified in the PWMFAULTVAL register. In other words, if a bit is set in the PWMFAULT, PWMFAULTVAL, and PWMINVERT registers, the output on the MnPWMn signal is 0, not 1 as specified in the PWMFAULTVAL register. 20.4 Initialization and Configuration The following example shows how to initialize PWM Generator 0 with a 25-kHz frequency, a 25% duty cycle on the MnPWM0 pin, and a 75% duty cycle on the MnPWM1 pin. This example assumes the system clock is 20 MHz. 1. Enable the PWM clock by writing a value of 0x0010.0000 to the RCGC0 register in the System Control module (see page 293). 2. Enable the clock to the appropriate GPIO module via the RCGC2 register in the System Control module (see page 300). 3. In the GPIO module, enable the appropriate pins for their alternate function using the GPIOAFSEL register. To determine which GPIOs to configure, see Table 23-4 on page 1387. 4. Configure the PMCn fields in the GPIOPCTL register to assign the PWM signals to the appropriate pins (see page 717 and Table 23-5 on page 1398). 5. Configure the Run-Mode Clock Configuration (RCC) register in the System Control module to use the PWM divide (USEPWMDIV) and set the divider (PWMDIV) to divide by 2 (000). 6. Configure the PWM generator for countdown mode with immediate updates to the parameters. ■ Write the PWM0CTL register with a value of 0x0000.0000. ■ Write the PWM0GENA register with a value of 0x0000.008C. ■ Write the PWM0GENB register with a value of 0x0000.080C. 7. Set the period. For a 25-KHz frequency, the period = 1/25,000, or 40 microseconds. The PWM clock source is 10 MHz; the system clock divided by 2. Thus there are 400 clock ticks per period. Use this value to set the PWM0LOAD register. In Count-Down mode, set the LOAD field in the PWM0LOAD register to the requested period minus one. ■ Write the PWM0LOAD register with a value of 0x0000.018F. 8. Set the pulse width of the MnPWM0 pin for a 25% duty cycle. ■ Write the PWM0CMPA register with a value of 0x0000.012B. 9. Set the pulse width of the MnPWM1 pin for a 75% duty cycle. 1264 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller ■ Write the PWM0CMPB register with a value of 0x0000.0063. 10. Start the timers in PWM generator 0. ■ Write the PWM0CTL register with a value of 0x0000.0001. 11. Enable PWM outputs. ■ Write the PWMENABLE register with a value of 0x0000.0003. 20.5 Register Map Table 20-2 on page 1265 lists the PWM registers. The offset listed is a hexadecimal increment to the register's address, relative to the PWM module's base address: ■ PWM0: 0x4002.8000 ■ PWM1: 0x4002.9000 Note that the PWM module clock must be enabled before the registers can be programmed (see page 293). There must be a delay of 3 system clocks after the PWM module clock is enabled before any PWM module registers are accessed. Table 20-2. PWM Register Map Description See page 0x0000.0000 PWM Master Control 1269 R/W 0x0000.0000 PWM Time Base Sync 1271 PWMENABLE R/W 0x0000.0000 PWM Output Enable 1272 0x00C PWMINVERT R/W 0x0000.0000 PWM Output Inversion 1274 0x010 PWMFAULT R/W 0x0000.0000 PWM Output Fault 1276 0x014 PWMINTEN R/W 0x0000.0000 PWM Interrupt Enable 1278 0x018 PWMRIS RO 0x0000.0000 PWM Raw Interrupt Status 1280 0x01C PWMISC R/W1C 0x0000.0000 PWM Interrupt Status and Clear 1283 0x020 PWMSTATUS RO 0x0000.0000 PWM Status 1286 0x024 PWMFAULTVAL R/W 0x0000.0000 PWM Fault Condition Value 1288 0x028 PWMENUPD R/W 0x0000.0000 PWM Enable Update 1290 0x040 PWM0CTL R/W 0x0000.0000 PWM0 Control 1294 0x044 PWM0INTEN R/W 0x0000.0000 PWM0 Interrupt and Trigger Enable 1299 0x048 PWM0RIS RO 0x0000.0000 PWM0 Raw Interrupt Status 1302 0x04C PWM0ISC R/W1C 0x0000.0000 PWM0 Interrupt Status and Clear 1304 0x050 PWM0LOAD R/W 0x0000.0000 PWM0 Load 1306 0x054 PWM0COUNT RO 0x0000.0000 PWM0 Counter 1307 0x058 PWM0CMPA R/W 0x0000.0000 PWM0 Compare A 1308 Offset Name Type Reset 0x000 PWMCTL R/W 0x004 PWMSYNC 0x008 November 08, 2011 1265 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Table 20-2. PWM Register Map (continued) Description See page 0x0000.0000 PWM0 Compare B 1309 R/W 0x0000.0000 PWM0 Generator A Control 1310 PWM0GENB R/W 0x0000.0000 PWM0 Generator B Control 1313 0x068 PWM0DBCTL R/W 0x0000.0000 PWM0 Dead-Band Control 1316 0x06C PWM0DBRISE R/W 0x0000.0000 PWM0 Dead-Band Rising-Edge Delay 1317 0x070 PWM0DBFALL R/W 0x0000.0000 PWM0 Dead-Band Falling-Edge-Delay 1318 0x074 PWM0FLTSRC0 R/W 0x0000.0000 PWM0 Fault Source 0 1319 0x078 PWM0FLTSRC1 R/W 0x0000.0000 PWM0 Fault Source 1 1321 0x07C PWM0MINFLTPER R/W 0x0000.0000 PWM0 Minimum Fault Period 1324 0x080 PWM1CTL R/W 0x0000.0000 PWM1 Control 1294 0x084 PWM1INTEN R/W 0x0000.0000 PWM1 Interrupt and Trigger Enable 1299 0x088 PWM1RIS RO 0x0000.0000 PWM1 Raw Interrupt Status 1302 0x08C PWM1ISC R/W1C 0x0000.0000 PWM1 Interrupt Status and Clear 1304 0x090 PWM1LOAD R/W 0x0000.0000 PWM1 Load 1306 0x094 PWM1COUNT RO 0x0000.0000 PWM1 Counter 1307 0x098 PWM1CMPA R/W 0x0000.0000 PWM1 Compare A 1308 0x09C PWM1CMPB R/W 0x0000.0000 PWM1 Compare B 1309 0x0A0 PWM1GENA R/W 0x0000.0000 PWM1 Generator A Control 1310 0x0A4 PWM1GENB R/W 0x0000.0000 PWM1 Generator B Control 1313 0x0A8 PWM1DBCTL R/W 0x0000.0000 PWM1 Dead-Band Control 1316 0x0AC PWM1DBRISE R/W 0x0000.0000 PWM1 Dead-Band Rising-Edge Delay 1317 0x0B0 PWM1DBFALL R/W 0x0000.0000 PWM1 Dead-Band Falling-Edge-Delay 1318 0x0B4 PWM1FLTSRC0 R/W 0x0000.0000 PWM1 Fault Source 0 1319 0x0B8 PWM1FLTSRC1 R/W 0x0000.0000 PWM1 Fault Source 1 1321 0x0BC PWM1MINFLTPER R/W 0x0000.0000 PWM1 Minimum Fault Period 1324 0x0C0 PWM2CTL R/W 0x0000.0000 PWM2 Control 1294 0x0C4 PWM2INTEN R/W 0x0000.0000 PWM2 Interrupt and Trigger Enable 1299 0x0C8 PWM2RIS RO 0x0000.0000 PWM2 Raw Interrupt Status 1302 0x0CC PWM2ISC R/W1C 0x0000.0000 PWM2 Interrupt Status and Clear 1304 0x0D0 PWM2LOAD R/W 0x0000.0000 PWM2 Load 1306 0x0D4 PWM2COUNT RO 0x0000.0000 PWM2 Counter 1307 0x0D8 PWM2CMPA R/W 0x0000.0000 PWM2 Compare A 1308 Offset Name Type Reset 0x05C PWM0CMPB R/W 0x060 PWM0GENA 0x064 1266 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 20-2. PWM Register Map (continued) Description See page 0x0000.0000 PWM2 Compare B 1309 R/W 0x0000.0000 PWM2 Generator A Control 1310 PWM2GENB R/W 0x0000.0000 PWM2 Generator B Control 1313 0x0E8 PWM2DBCTL R/W 0x0000.0000 PWM2 Dead-Band Control 1316 0x0EC PWM2DBRISE R/W 0x0000.0000 PWM2 Dead-Band Rising-Edge Delay 1317 0x0F0 PWM2DBFALL R/W 0x0000.0000 PWM2 Dead-Band Falling-Edge-Delay 1318 0x0F4 PWM2FLTSRC0 R/W 0x0000.0000 PWM2 Fault Source 0 1319 0x0F8 PWM2FLTSRC1 R/W 0x0000.0000 PWM2 Fault Source 1 1321 0x0FC PWM2MINFLTPER R/W 0x0000.0000 PWM2 Minimum Fault Period 1324 0x100 PWM3CTL R/W 0x0000.0000 PWM3 Control 1294 0x104 PWM3INTEN R/W 0x0000.0000 PWM3 Interrupt and Trigger Enable 1299 0x108 PWM3RIS RO 0x0000.0000 PWM3 Raw Interrupt Status 1302 0x10C PWM3ISC R/W1C 0x0000.0000 PWM3 Interrupt Status and Clear 1304 0x110 PWM3LOAD R/W 0x0000.0000 PWM3 Load 1306 0x114 PWM3COUNT RO 0x0000.0000 PWM3 Counter 1307 0x118 PWM3CMPA R/W 0x0000.0000 PWM3 Compare A 1308 0x11C PWM3CMPB R/W 0x0000.0000 PWM3 Compare B 1309 0x120 PWM3GENA R/W 0x0000.0000 PWM3 Generator A Control 1310 0x124 PWM3GENB R/W 0x0000.0000 PWM3 Generator B Control 1313 0x128 PWM3DBCTL R/W 0x0000.0000 PWM3 Dead-Band Control 1316 0x12C PWM3DBRISE R/W 0x0000.0000 PWM3 Dead-Band Rising-Edge Delay 1317 0x130 PWM3DBFALL R/W 0x0000.0000 PWM3 Dead-Band Falling-Edge-Delay 1318 0x134 PWM3FLTSRC0 R/W 0x0000.0000 PWM3 Fault Source 0 1319 0x138 PWM3FLTSRC1 R/W 0x0000.0000 PWM3 Fault Source 1 1321 0x13C PWM3MINFLTPER R/W 0x0000.0000 PWM3 Minimum Fault Period 1324 0x800 PWM0FLTSEN R/W 0x0000.0000 PWM0 Fault Pin Logic Sense 1325 0x804 PWM0FLTSTAT0 - 0x0000.0000 PWM0 Fault Status 0 1326 0x808 PWM0FLTSTAT1 - 0x0000.0000 PWM0 Fault Status 1 1328 0x880 PWM1FLTSEN R/W 0x0000.0000 PWM1 Fault Pin Logic Sense 1325 0x884 PWM1FLTSTAT0 - 0x0000.0000 PWM1 Fault Status 0 1326 0x888 PWM1FLTSTAT1 - 0x0000.0000 PWM1 Fault Status 1 1328 0x900 PWM2FLTSEN R/W 0x0000.0000 PWM2 Fault Pin Logic Sense 1325 Offset Name Type Reset 0x0DC PWM2CMPB R/W 0x0E0 PWM2GENA 0x0E4 November 08, 2011 1267 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Table 20-2. PWM Register Map (continued) Description See page 0x0000.0000 PWM2 Fault Status 0 1326 - 0x0000.0000 PWM2 Fault Status 1 1328 R/W 0x0000.0000 PWM3 Fault Pin Logic Sense 1325 PWM3FLTSTAT0 - 0x0000.0000 PWM3 Fault Status 0 1326 0x988 PWM3FLTSTAT1 - 0x0000.0000 PWM3 Fault Status 1 1328 0xFC0 PWMPP RO 0x0000.0344 PWM Peripheral Properties 1331 0xFC4 PWMPC R/W 0x0000.0000 PWM Peripheral Configuration 1333 Offset Name Type Reset 0x904 PWM2FLTSTAT0 - 0x908 PWM2FLTSTAT1 0x980 PWM3FLTSEN 0x984 20.6 Register Descriptions The remainder of this section lists and describes the PWM registers, in numerical order by address offset. 1268 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 1: PWM Master Control (PWMCTL), offset 0x000 This register provides master control over the PWM generation blocks. PWM Master Control (PWMCTL) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved Type Reset reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 GLOBALSYNC3 GLOBALSYNC2 GLOBALSYNC1 GLOBALSYNC0 RO 0 Bit/Field Name Type Reset 31:4 reserved RO 0x0000 3 GLOBALSYNC3 R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Update PWM Generator 3 Value Description 1 Any queued update to a load or comparator register in PWM generator 3 is applied the next time the corresponding counter becomes zero. 0 No effect. This bit automatically clears when the updates have completed; it cannot be cleared by software. 2 GLOBALSYNC2 R/W 0 Update PWM Generator 2 Value Description 1 Any queued update to a load or comparator register in PWM generator 2 is applied the next time the corresponding counter becomes zero. 0 No effect. This bit automatically clears when the updates have completed; it cannot be cleared by software. 1 GLOBALSYNC1 R/W 0 Update PWM Generator 1 Value Description 1 Any queued update to a load or comparator register in PWM generator 1 is applied the next time the corresponding counter becomes zero. 0 No effect. This bit automatically clears when the updates have completed; it cannot be cleared by software. November 08, 2011 1269 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 0 GLOBALSYNC0 R/W 0 Description Update PWM Generator 0 Value Description 1 Any queued update to a load or comparator register in PWM generator 0 is applied the next time the corresponding counter becomes zero. 0 No effect. This bit automatically clears when the updates have completed; it cannot be cleared by software. 1270 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 2: PWM Time Base Sync (PWMSYNC), offset 0x004 This register provides a method to perform synchronization of the counters in the PWM generation blocks. Setting a bit in this register causes the specified counter to reset back to 0; setting multiple bits resets multiple counters simultaneously. The bits auto-clear after the reset has occurred; reading them back as zero indicates that the synchronization has completed. PWM Time Base Sync (PWMSYNC) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x004 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 SYNC3 SYNC2 SYNC1 SYNC0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 SYNC3 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Reset Generator 3 Counter Value Description 2 SYNC2 R/W 0 1 Resets the PWM generator 3 counter. 0 No effect. Reset Generator 2 Counter Value Description 1 SYNC1 R/W 0 1 Resets the PWM generator 2 counter. 0 No effect. Reset Generator 1 Counter Value Description 0 SYNC0 R/W 0 1 Resets the PWM generator 1 counter. 0 No effect. Reset Generator 0 Counter Value Description 1 Resets the PWM generator 0 counter. 0 No effect. November 08, 2011 1271 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 3: PWM Output Enable (PWMENABLE), offset 0x008 This register provides a master control of which generated pwmA' and pwmB' signals are output to the MnPWMn pins. By disabling a PWM output, the generation process can continue (for example, when the time bases are synchronized) without driving PWM signals to the pins. When bits in this register are set, the corresponding pwmA' or pwmB' signal is passed through to the output stage. When bits are clear, the pwmA' or pwmB' signal is replaced by a zero value which is also passed to the output stage. The PWMINVERT register controls the output stage, so if the corresponding bit is set in that register, the value seen on the MnPWMn signal is inverted from what is configured by the bits in this register. Updates to the bits in this register can be immediate or locally or globally synchronized to the next synchronous update as controlled by the ENUPDn fields in the PWMENUPD register. PWM Output Enable (PWMENABLE) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved Type Reset reserved Type Reset PWM7EN PWM6EN PWM5EN PWM4EN PWM3EN PWM2EN PWM1EN PWM0EN RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 PWM7EN R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. MnPWM7 Output Enable Value Description 6 PWM6EN R/W 0 1 The generated pwm3B' signal is passed to the MnPWM7 pin. 0 The MnPWM7 signal has a zero value. MnPWM6 Output Enable Value Description 5 PWM5EN R/W 0 1 The generated pwm3A' signal is passed to the MnPWM6 pin. 0 The MnPWM6 signal has a zero value. MnPWM5 Output Enable Value Description 1 The generated pwm2B' signal is passed to the MnPWM5 pin. 0 The MnPWM5 signal has a zero value. 1272 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 4 PWM4EN R/W 0 Description MnPWM4 Output Enable Value Description 3 PWM3EN R/W 0 1 The generated pwm2A' signal is passed to the MnPWM4 pin. 0 The MnPWM4 signal has a zero value. MnPWM3 Output Enable Value Description 2 PWM2EN R/W 0 1 The generated pwm1B' signal is passed to the MnPWM3 pin. 0 The MnPWM3 signal has a zero value. MnPWM2 Output Enable Value Description 1 PWM1EN R/W 0 1 The generated pwm1A' signal is passed to the MnPWM2 pin. 0 The MnPWM2 signal has a zero value. MnPWM1 Output Enable Value Description 0 PWM0EN R/W 0 1 The generated pwm0B' signal is passed to the MnPWM1 pin. 0 The MnPWM1 signal has a zero value. MnPWM0 Output Enable Value Description 1 The generated pwm0A' signal is passed to the MnPWM0 pin. 0 The MnPWM0 signal has a zero value. November 08, 2011 1273 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 4: PWM Output Inversion (PWMINVERT), offset 0x00C This register provides a master control of the polarity of the MnPWMn signals on the device pins. The pwmA' and pwmB' signals generated by the PWM generator are active High; but can be made active Low via this register. Disabled PWM channels are also passed through the output inverter (if so configured) so that inactive signals can be High. In addition, if the PWMFAULT register enables a specific value to be placed on the MnPWMn signals during a fault condition, that value is inverted if the corresponding bit in this register is set. PWM Output Inversion (PWMINVERT) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x00C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved Type Reset reserved Type Reset PWM7INV PWM6INV PWM5INV PWM4INV PWM3INV PWM2INV PWM1INV PWM0INV RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 PWM7INV R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Invert MnPWM7 Signal Value Description 6 PWM6INV R/W 0 1 The MnPWM7 signal is inverted. 0 The MnPWM7 signal is not inverted. Invert MnPWM6 Signal Value Description 5 PWM5INV R/W 0 1 The MnPWM6 signal is inverted. 0 The MnPWM6 signal is not inverted. Invert MnPWM5 Signal Value Description 4 PWM4INV R/W 0 1 The MnPWM5 signal is inverted. 0 The MnPWM5 signal is not inverted. Invert MnPWM4 Signal Value Description 1 The MnPWM4 signal is inverted. 0 The MnPWM4 signal is not inverted. 1274 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 3 PWM3INV R/W 0 Description Invert MnPWM3 Signal Value Description 2 PWM2INV R/W 0 1 The MnPWM3 signal is inverted. 0 The MnPWM3 signal is not inverted. Invert MnPWM2 Signal Value Description 1 PWM1INV R/W 0 1 The MnPWM2 signal is inverted. 0 The MnPWM2 signal is not inverted. Invert MnPWM1 Signal Value Description 0 PWM0INV R/W 0 1 The MnPWM1 signal is inverted. 0 The MnPWM1 signal is not inverted. Invert MnPWM0 Signal Value Description 1 The MnPWM0 signal is inverted. 0 The MnPWM0 signal is not inverted. November 08, 2011 1275 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 5: PWM Output Fault (PWMFAULT), offset 0x010 This register controls the behavior of the MnPWMn outputs in the presence of fault conditions. Both the fault inputs (MnFAULTn pins and digital comparator outputs) and debug events are considered fault conditions. On a fault condition, each pwmA' or pwmB' signal can be passed through unmodified or driven to the value specified by the corresponding bit in the PWMFAULTVAL register. For outputs that are configured for pass-through, the debug event handling on the corresponding PWM generator also determines if the pwmA' or pwmB' signal continues to be generated. Fault condition control occurs before the output inverter, so PWM signals driven to a specified value on fault are inverted if the channel is configured for inversion (therefore, the pin is driven to the logical complement of the specified value on a fault condition). PWM Output Fault (PWMFAULT) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 FAULT7 R/W 0 RO 0 RO 0 7 6 5 4 3 2 1 0 FAULT7 FAULT6 FAULT5 FAULT4 FAULT3 FAULT2 FAULT1 FAULT0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. MnPWM7 Fault Value Description 6 FAULT6 R/W 0 1 The MnPWM7 output signal is driven to the value specified by the PWM7 bit in the PWMFAULTVAL register. 0 The generated pwm3B' signal is passed to the MnPWM7 pin. MnPWM6 Fault Value Description 5 FAULT5 R/W 0 1 The MnPWM6 output signal is driven to the value specified by the PWM6 bit in the PWMFAULTVAL register. 0 The generated pwm3A' signal is passed to the MnPWM6 pin. MnPWM5 Fault Value Description 1 The MnPWM5 output signal is driven to the value specified by the PWM5 bit in the PWMFAULTVAL register. 0 The generated pwm2B' signal is passed to the MnPWM5 pin. 1276 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 4 FAULT4 R/W 0 Description MnPWM4 Fault Value Description 3 FAULT3 R/W 0 1 The MnPWM4 output signal is driven to the value specified by the PWM4 bit in the PWMFAULTVAL register. 0 The generated pwm2A' signal is passed to the MnPWM4 pin. MnPWM3 Fault Value Description 2 FAULT2 R/W 0 1 The MnPWM3 output signal is driven to the value specified by the PWM3 bit in the PWMFAULTVAL register. 0 The generated pwm1B' signal is passed to the MnPWM3 pin. MnPWM2 Fault Value Description 1 FAULT1 R/W 0 1 The MnPWM2 output signal is driven to the value specified by the PWM2 bit in the PWMFAULTVAL register. 0 The generated pwm1A' signal is passed to the MnPWM2 pin. MnPWM1 Fault Value Description 0 FAULT0 R/W 0 1 The MnPWM1 output signal is driven to the value specified by the PWM1 bit in the PWMFAULTVAL register. 0 The generated pwm0B' signal is passed to the MnPWM1 pin. MnPWM0 Fault Value Description 1 The MnPWM0 output signal is driven to the value specified by the PWM0 bit in the PWMFAULTVAL register. 0 The generated pwm0A' signal is passed to the MnPWM0 pin. November 08, 2011 1277 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 6: PWM Interrupt Enable (PWMINTEN), offset 0x014 This register controls the global interrupt generation capabilities of the PWM module. The events that can cause an interrupt are the fault input and the individual interrupts from the PWM generators. PWM Interrupt Enable (PWMINTEN) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x014 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 25 24 23 22 21 20 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset 18 17 16 INTFAULT3 INTFAULT2 INTFAULT1 INTFAULT0 reserved Type Reset 19 INTPWM3 INTPWM2 INTPWM1 INTPWM0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:20 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 19 INTFAULT3 R/W 0 Interrupt Fault 3 Value Description 18 INTFAULT2 R/W 0 1 An interrupt is sent to the interrupt controller when the fault condition for PWM generator 3 is asserted. 0 The fault condition for PWM generator 3 is suppressed and not sent to the interrupt controller. Interrupt Fault 2 Value Description 17 INTFAULT1 R/W 0 1 An interrupt is sent to the interrupt controller when the fault condition for PWM generator 2 is asserted. 0 The fault condition for PWM generator 2 is suppressed and not sent to the interrupt controller. Interrupt Fault 1 Value Description 1 An interrupt is sent to the interrupt controller when the fault condition for PWM generator 1 is asserted. 0 The fault condition for PWM generator 1 is suppressed and not sent to the interrupt controller. 1278 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 16 INTFAULT0 R/W 0 Description Interrupt Fault 0 Value Description 15:4 reserved RO 0x000 3 INTPWM3 R/W 0 1 An interrupt is sent to the interrupt controller when the fault condition for PWM generator 0 is asserted. 0 The fault condition for PWM generator 0 is suppressed and not sent to the interrupt controller. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. PWM3 Interrupt Enable Value Description 2 INTPWM2 R/W 0 1 An interrupt is sent to the interrupt controller when the PWM generator 3 block asserts an interrupt. 0 The PWM generator 3 interrupt is suppressed and not sent to the interrupt controller. PWM2 Interrupt Enable Value Description 1 INTPWM1 R/W 0 1 An interrupt is sent to the interrupt controller when the PWM generator 2 block asserts an interrupt. 0 The PWM generator 2 interrupt is suppressed and not sent to the interrupt controller. PWM1 Interrupt Enable Value Description 0 INTPWM0 R/W 0 1 An interrupt is sent to the interrupt controller when the PWM generator 1 block asserts an interrupt. 0 The PWM generator 1 interrupt is suppressed and not sent to the interrupt controller. PWM0 Interrupt Enable Value Description 1 An interrupt is sent to the interrupt controller when the PWM generator 0 block asserts an interrupt. 0 The PWM generator 0 interrupt is suppressed and not sent to the interrupt controller. November 08, 2011 1279 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 7: PWM Raw Interrupt Status (PWMRIS), offset 0x018 This register provides the current set of interrupt sources that are asserted, regardless of whether they are enabled to cause an interrupt to be asserted to the interrupt controller. The fault interrupt is asserted based on the fault condition source that is specified by the PWMnCTL, PWMnFLTSRC0 and PWMnFLTSRC1 registers. The fault interrupt is latched on detection and must be cleared through the PWM Interrupt Status and Clear (PWMISC) register. The actual value of the MnFAULTn signals can be observed using the PWMSTATUS register. The PWM generator interrupts simply reflect the status of the PWM generators and are cleared via the interrupt status register in the PWM generator blocks. If a bit is set, the event is active; if a bit is clear the event is not active. PWM Raw Interrupt Status (PWMRIS) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x018 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 19 18 17 16 INTFAULT3 INTFAULT2 INTFAULT1 INTFAULT0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 INTPWM3 INTPWM2 INTPWM1 INTPWM0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:20 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 19 INTFAULT3 RO 0 Interrupt Fault PWM 3 Value Description 1 The fault condition for PWM generator 3 is asserted. 0 The fault condition for PWM generator 3 has not been asserted. This bit is cleared by writing a 1 to the INTFAULT3 bit in the PWMISC register. 18 INTFAULT2 RO 0 Interrupt Fault PWM 2 Value Description 1 The fault condition for PWM generator 2 is asserted. 0 The fault condition for PWM generator 2 has not been asserted. This bit is cleared by writing a 1 to the INTFAULT2 bit in the PWMISC register. 1280 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 17 INTFAULT1 RO 0 Description Interrupt Fault PWM 1 Value Description 1 The fault condition for PWM generator 1 is asserted. 0 The fault condition for PWM generator 1 has not been asserted. This bit is cleared by writing a 1 to the INTFAULT1 bit in the PWMISC register. 16 INTFAULT0 RO 0 Interrupt Fault PWM 0 Value Description 1 The fault condition for PWM generator 0 is asserted. 0 The fault condition for PWM generator 0 has not been asserted. This bit is cleared by writing a 1 to the INTFAULT0 bit in the PWMISC register. 15:4 reserved RO 0x000 3 INTPWM3 RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. PWM3 Interrupt Asserted Value Description 1 The PWM generator 3 block interrupt is asserted. 0 The PWM generator 3 block interrupt has not been asserted. The PWM3RIS register shows the source of this interrupt. This bit is cleared by writing a 1 to the corresponding bit in the PWM3ISC register. 2 INTPWM2 RO 0 PWM2 Interrupt Asserted Value Description 1 The PWM generator 2 block interrupt is asserted. 0 The PWM generator 2 block interrupt has not been asserted. The PWM2RIS register shows the source of this interrupt. This bit is cleared by writing a 1 to the corresponding bit in the PWM2ISC register. 1 INTPWM1 RO 0 PWM1 Interrupt Asserted Value Description 1 The PWM generator 1 block interrupt is asserted. 0 The PWM generator 1 block interrupt has not been asserted. The PWM1RIS register shows the source of this interrupt. This bit is cleared by writing a 1 to the corresponding bit in the PWM1ISC register. November 08, 2011 1281 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 0 INTPWM0 RO 0 Description PWM0 Interrupt Asserted Value Description 1 The PWM generator 0 block interrupt is asserted. 0 The PWM generator 0 block interrupt has not been asserted. The PWM0RIS register shows the source of this interrupt. This bit is cleared by writing a 1 to the corresponding bit in the PWM0ISC register. 1282 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 8: PWM Interrupt Status and Clear (PWMISC), offset 0x01C This register provides a summary of the interrupt status of the individual PWM generator blocks. If a fault interrupt is set, the corresponding MnFAULTn input has caused an interrupt. For the fault interrupt, a write of 1 to that bit position clears the latched interrupt status. If an block interrupt bit is set, the corresponding generator block is asserting an interrupt. The individual interrupt status registers, PWMnISC, in each block must be consulted to determine the reason for the interrupt and used to clear the interrupt. PWM Interrupt Status and Clear (PWMISC) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x01C Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 25 24 23 22 21 20 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset 18 17 16 INTFAULT3 INTFAULT2 INTFAULT1 INTFAULT0 reserved Type Reset 19 INTPWM3 INTPWM2 INTPWM1 INTPWM0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:20 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 19 INTFAULT3 R/W1C 0 FAULT3 Interrupt Asserted Value Description 1 An enabled interrupt for the fault condition for PWM generator 3 is asserted or is latched. 0 The fault condition for PWM generator 3 has not been asserted or is not enabled. Writing a 1 to this bit clears it and the INTFAULT3 bit in the PWMRIS register. 18 INTFAULT2 R/W1C 0 FAULT2 Interrupt Asserted Value Description 1 An enabled interrupt for the fault condition for PWM generator 2 is asserted or is latched. 0 The fault condition for PWM generator 2 has not been asserted or is not enabled. Writing a 1 to this bit clears it and the INTFAULT2 bit in the PWMRIS register. November 08, 2011 1283 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 17 INTFAULT1 R/W1C 0 Description FAULT1 Interrupt Asserted Value Description 1 An enabled interrupt for the fault condition for PWM generator 1 is asserted or is latched. 0 The fault condition for PWM generator 1 has not been asserted or is not enabled. Writing a 1 to this bit clears it and the INTFAULT1 bit in the PWMRIS register. 16 INTFAULT0 R/W1C 0 FAULT0 Interrupt Asserted Value Description 1 An enabled interrupt for the fault condition for PWM generator 0 is asserted or is latched. 0 The fault condition for PWM generator 0 has not been asserted or is not enabled. Writing a 1 to this bit clears it and the INTFAULT0 bit in the PWMRIS register. 15:4 reserved RO 0x000 3 INTPWM3 RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. PWM3 Interrupt Status Value Description 1 An enabled interrupt for the PWM generator 3 block is asserted. 0 The PWM generator 3 block interrupt is not asserted or is not enabled. The PWM3RIS register shows the source of this interrupt. This bit is cleared by writing a 1 to the corresponding bit in the PWM3ISC register. 2 INTPWM2 RO 0 PWM2 Interrupt Status Value Description 1 An enabled interrupt for the PWM generator 2 block is asserted. 0 The PWM generator 2 block interrupt is not asserted or is not enabled. The PWM2RIS register shows the source of this interrupt. This bit is cleared by writing a 1 to the corresponding bit in the PWM2ISC register. 1 INTPWM1 RO 0 PWM1 Interrupt Status Value Description 1 An enabled interrupt for the PWM generator 1 block is asserted. 0 The PWM generator 1 block interrupt is not asserted or is not enabled. The PWM1RIS register shows the source of this interrupt. This bit is cleared by writing a 1 to the corresponding bit in the PWM1ISC register. 1284 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 0 INTPWM0 RO 0 Description PWM0 Interrupt Status Value Description 1 An enabled interrupt for the PWM generator 0 block is asserted. 0 The PWM generator 0 block interrupt is not asserted or is not enabled. The PWM0RIS register shows the source of this interrupt. This bit is cleared by writing a 1 to the corresponding bit in the PWM0ISC register. November 08, 2011 1285 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 9: PWM Status (PWMSTATUS), offset 0x020 This register provides the unlatched status of the PWM generator fault condition. PWM Status (PWMSTATUS) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x020 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 FAULT3 FAULT2 FAULT1 FAULT0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 FAULT3 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Generator 3 Fault Status Value Description 1 The fault condition for PWM generator 3 is asserted. If the FLTSRC bit in the PWM3CTL register is clear, the input is the source of the fault condition, and is therefore asserted. 0 2 FAULT2 RO 0 The fault condition for PWM generator 3 is not asserted. Generator 2 Fault Status Value Description 1 The fault condition for PWM generator 2 is asserted. If the FLTSRC bit in the PWM2CTL register is clear, the input is the source of the fault condition, and is therefore asserted. 0 1 FAULT1 RO 0 The fault condition for PWM generator 2 is not asserted. Generator 1 Fault Status Value Description 1 The fault condition for PWM generator 1 is asserted. If the FLTSRC bit in the PWM1CTL register is clear, the input is the source of the fault condition, and is therefore asserted. 0 The fault condition for PWM generator 1 is not asserted. 1286 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 0 FAULT0 RO 0 Description Generator 0 Fault Status Value Description 1 The fault condition for PWM generator 0 is asserted. If the FLTSRC bit in the PWM0CTL register is clear, the input is the source of the fault condition, and is therefore asserted. 0 The fault condition for PWM generator 0 is not asserted. November 08, 2011 1287 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 10: PWM Fault Condition Value (PWMFAULTVAL), offset 0x024 This register specifies the output value driven on the MnPWMn signals during a fault condition if enabled by the corresponding bit in the PWMFAULT register. Note that if the corresponding bit in the PWMINVERT register is set, the output value is driven to the logical NOT of the bit value in this register. PWM Fault Condition Value (PWMFAULTVAL) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 PWM7 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. MnPWM7 Fault Value Value Description 6 PWM6 R/W 0 1 The MnPWM7 output signal is driven High during fault conditions if the FAULT7 bit in the PWMFAULT register is set. 0 The MnPWM7 output signal is driven Low during fault conditions if the FAULT7 bit in the PWMFAULT register is set. MnPWM6 Fault Value Value Description 5 PWM5 R/W 0 1 The MnPWM6 output signal is driven High during fault conditions if the FAULT6 bit in the PWMFAULT register is set. 0 The MnPWM6 output signal is driven Low during fault conditions if the FAULT6 bit in the PWMFAULT register is set. MnPWM5 Fault Value Value Description 1 The MnPWM5 output signal is driven High during fault conditions if the FAULT5 bit in the PWMFAULT register is set. 0 The MnPWM5 output signal is driven Low during fault conditions if the FAULT5 bit in the PWMFAULT register is set. 1288 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 4 PWM4 R/W 0 Description MnPWM4 Fault Value Value Description 3 PWM3 R/W 0 1 The MnPWM4 output signal is driven High during fault conditions if the FAULT4 bit in the PWMFAULT register is set. 0 The MnPWM4 output signal is driven Low during fault conditions if the FAULT4 bit in the PWMFAULT register is set. MnPWM3 Fault Value Value Description 1 0 2 PWM2 R/W 0 The MnPWM3 output signal is driven High during fault conditions if the FAULT3 bit in the PWMFAULT register is set. The MnPWM3 output signal is driven Low during fault conditions if the FAULT3 bit in the PWMFAULT register is set. MnPWM2 Fault Value Value Description 1 PWM1 R/W 0 1 The MnPWM2 output signal is driven High during fault conditions if the FAULT2 bit in the PWMFAULT register is set. 0 The MnPWM2 output signal is driven Low during fault conditions if the FAULT2 bit in the PWMFAULT register is set. MnPWM1 Fault Value Value Description 0 PWM0 R/W 0 1 The MnPWM1 output signal is driven High during fault conditions if the FAULT1 bit in the PWMFAULT register is set. 0 The MnPWM1 output signal is driven Low during fault conditions if the FAULT1 bit in the PWMFAULT register is set. MnPWM0 Fault Value Value Description 1 The MnPWM0 output signal is driven High during fault conditions if the FAULT0 bit in the PWMFAULT register is set. 0 The MnPWM0 output signal is driven Low during fault conditions if the FAULT0 bit in the PWMFAULT register is set. November 08, 2011 1289 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 11: PWM Enable Update (PWMENUPD), offset 0x028 This register specifies when updates to the PWMnEN bit in the PWMENABLE register are performed. The PWMnEN bit enables the pwmA' or pwmB' output to be passed to the microcontroller's pin. Updates can be immediate or locally or globally synchronized to the next synchronous update. PWM Enable Update (PWMENUPD) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x028 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset ENUPD7 Type Reset R/W 0 R/W 0 ENUPD6 R/W 0 R/W 0 ENUPD5 R/W 0 R/W 0 ENUPD4 R/W 0 ENUPD3 ENUPD2 ENUPD1 ENUPD0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:14 ENUPD7 R/W 0 MnPWM07 Enable Update Mode Value Description 0x0 Immediate Writes to the PWM7EN bit in the PWMENABLE register are used by the PWM generator immediately. 0x1 Reserved 0x2 Locally Synchronized Writes to the PWM7EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0. 0x3 Globally Synchronized Writes to the PWM7EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0 after a synchronous update has been requested through the PWM Master Control (PWMCTL) register. 1290 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 13:12 ENUPD6 R/W 0 Description MnPWM6 Enable Update Mode Value Description 0x0 Immediate Writes to the PWM6EN bit in the PWMENABLE register are used by the PWM generator immediately. 0x1 Reserved 0x2 Locally Synchronized Writes to the PWM6EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0. 0x3 Globally Synchronized Writes to the PWM6EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0 after a synchronous update has been requested through the PWM Master Control (PWMCTL) register. 11:10 ENUPD5 R/W 0 MnPWM5 Enable Update Mode Value Description 0x0 Immediate Writes to the PWM5EN bit in the PWMENABLE register are used by the PWM generator immediately. 0x1 Reserved 0x2 Locally Synchronized Writes to the PWM5EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0. 0x3 Globally Synchronized Writes to the PWM5EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0 after a synchronous update has been requested through the PWM Master Control (PWMCTL) register. 9:8 ENUPD4 R/W 0 MnPWM4 Enable Update Mode Value Description 0x0 Immediate Writes to the PWM4EN bit in the PWMENABLE register are used by the PWM generator immediately. 0x1 Reserved 0x2 Locally Synchronized Writes to the PWM4EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0. 0x3 Globally Synchronized Writes to the PWM4EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0 after a synchronous update has been requested through the PWM Master Control (PWMCTL) register. November 08, 2011 1291 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 7:6 ENUPD3 R/W 0 Description MnPWM3 Enable Update Mode Value Description 0x0 Immediate Writes to the PWM3EN bit in the PWMENABLE register are used by the PWM generator immediately. 0x1 Reserved 0x2 Locally Synchronized Writes to the PWM3EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0. 0x3 Globally Synchronized Writes to the PWM3EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0 after a synchronous update has been requested through the PWM Master Control (PWMCTL) register. 5:4 ENUPD2 R/W 0 MnPWM2 Enable Update Mode Value Description 0x0 Immediate Writes to the PWM2EN bit in the PWMENABLE register are used by the PWM generator immediately. 0x1 Reserved 0x2 Locally Synchronized Writes to the PWM2EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0. 0x3 Globally Synchronized Writes to the PWM2EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0 after a synchronous update has been requested through the PWM Master Control (PWMCTL) register. 3:2 ENUPD1 R/W 0 MnPWM1 Enable Update Mode Value Description 0x0 Immediate Writes to the PWM1EN bit in the PWMENABLE register are used by the PWM generator immediately. 0x1 Reserved 0x2 Locally Synchronized Writes to the PWM1EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0. 0x3 Globally Synchronized Writes to the PWM1EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0 after a synchronous update has been requested through the PWM Master Control (PWMCTL) register. 1292 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 1:0 ENUPD0 R/W 0 Description MnPWM0 Enable Update Mode Value Description 0x0 Immediate Writes to the PWM0EN bit in the PWMENABLE register are used by the PWM generator immediately. 0x1 Reserved 0x2 Locally Synchronized Writes to the PWM0EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0. 0x3 Globally Synchronized Writes to the PWM0EN bit in the PWMENABLE register are used by the PWM generator the next time the counter is 0 after a synchronous update has been requested through the PWM Master Control (PWMCTL) register. November 08, 2011 1293 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 12: PWM0 Control (PWM0CTL), offset 0x040 Register 13: PWM1 Control (PWM1CTL), offset 0x080 Register 14: PWM2 Control (PWM2CTL), offset 0x0C0 Register 15: PWM3 Control (PWM3CTL), offset 0x100 These registers configure the PWM signal generation blocks (PWM0CTL controls the PWM generator 0 block, and so on). The Register Update mode, Debug mode, Counting mode, and Block Enable mode are all controlled via these registers. The blocks produce the PWM signals, which can be either two independent PWM signals (from the same counter), or a paired set of PWM signals with dead-band delays added. The PWM0 block produces the MnPWM0 and MnPWM1 outputs, the PWM1 block produces the MnPWM2 and MnPWM3 outputs, the PWM2 block produces the MnPWM4 and MnPWM5 outputs, and the PWM3 block produces the MnPWM6 and MnPWM7 outputs. PWM0 Control (PWM0CTL) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x040 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 DBFALLUPD Type Reset R/W 0 R/W 0 DBRISEUPD R/W 0 R/W 0 DBCTLUPD R/W 0 R/W 0 GENBUPD R/W 0 18 17 16 LATCH MINFLTPER FLTSRC GENAUPD R/W 0 R/W 0 R/W 0 RO 0 RO 0 RO 0 R/W 0 5 4 3 2 CMPBUPD CMPAUPD LOADUPD DEBUG R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 1 0 MODE ENABLE R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:19 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 18 LATCH R/W 0 Latch Fault Input Value Description 0 Fault Condition Not Latched A fault condition is in effect for as long as the generating source is asserting. 1 Fault Condition Latched A fault condition is set as the result of the assertion of the faulting source and is held (latched) while the PWMISC INTFAULTn bit is set. Clearing the INTFAULTn bit clears the fault condition. 1294 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 17 MINFLTPER R/W 0 Description Minimum Fault Period This bit specifies that the PWM generator enables a one-shot counter to provide a minimum fault condition period. The timer begins counting on the rising edge of the fault condition to extend the condition for a minimum duration of the count value. The timer ignores the state of the fault condition while counting. The minimum fault delay is in effect only when the MINFLTPER bit is set. If a detected fault is in the process of being extended when the MINFLTPER bit is cleared, the fault condition extension is aborted. The delay time is specified by the PWMnMINFLTPER register MFP field value. The effect of this is to pulse stretch the fault condition input. The delay value is defined by the PWM clock period. Because the fault input is not synchronized to the PWM clock, the period of the time is PWMClock * (MFP value + 1) or PWMClock * (MFP value + 2). The delay function makes sense only if the fault source is unlatched. A latched fault source makes the fault condition appear asserted until cleared by software and negates the utility of the extend feature. It applies to all fault condition sources as specified in the FLTSRC field. Value Description 16 FLTSRC R/W 0 0 The FAULT input deassertion is unaffected. 1 The PWMnMINFLTPER one-shot counter is active and extends the period of the fault condition to a minimum period. Fault Condition Source Value Description 15:14 DBFALLUPD R/W 0x0 0 The Fault condition is determined by the Fault0 input. 1 The Fault condition is determined by the configuration of the PWMnFLTSRC0 and PWMnFLTSRC1 registers. PWMnDBFALL Update Mode Value Description 0x0 Immediate The PWMnDBFALL register value is immediately updated on a write. 0x1 Reserved 0x2 Locally Synchronized Updates to the register are reflected to the generator the next time the counter is 0. 0x3 Globally Synchronized Updates to the register are delayed until the next time the counter is 0 after a synchronous update has been requested through the PWMCTL register. November 08, 2011 1295 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 13:12 DBRISEUPD R/W 0x0 Description PWMnDBRISE Update Mode Value Description 0x0 Immediate The PWMnDBRISE register value is immediately updated on a write. 0x1 Reserved 0x2 Locally Synchronized Updates to the register are reflected to the generator the next time the counter is 0. 0x3 Globally Synchronized Updates to the register are delayed until the next time the counter is 0 after a synchronous update has been requested through the PWMCTL register. 11:10 DBCTLUPD R/W 0x0 PWMnDBCTL Update Mode Value Description 0x0 Immediate The PWMnDBCTL register value is immediately updated on a write. 0x1 Reserved 0x2 Locally Synchronized Updates to the register are reflected to the generator the next time the counter is 0. 0x3 Globally Synchronized Updates to the register are delayed until the next time the counter is 0 after a synchronous update has been requested through the PWMCTL register. 9:8 GENBUPD R/W 0x0 PWMnGENB Update Mode Value Description 0x0 Immediate The PWMnGENB register value is immediately updated on a write. 0x1 Reserved 0x2 Locally Synchronized Updates to the register are reflected to the generator the next time the counter is 0. 0x3 Globally Synchronized Updates to the register are delayed until the next time the counter is 0 after a synchronous update has been requested through the PWMCTL register. 1296 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 7:6 GENAUPD R/W 0x0 Description PWMnGENA Update Mode Value Description 0x0 Immediate The PWMnGENA register value is immediately updated on a write. 0x1 Reserved 0x2 Locally Synchronized Updates to the register are reflected to the generator the next time the counter is 0. 0x3 Globally Synchronized Updates to the register are delayed until the next time the counter is 0 after a synchronous update has been requested through the PWMCTL register. 5 CMPBUPD R/W 0 Comparator B Update Mode Value Description 0 Locally Synchronized Updates to the PWMnCMPB register are reflected to the generator the next time the counter is 0. 1 Globally Synchronized Updates to the register are delayed until the next time the counter is 0 after a synchronous update has been requested through the PWMCTL register. 4 CMPAUPD R/W 0 Comparator A Update Mode Value Description 0 Locally Synchronized Updates to the PWMnCMPA register are reflected to the generator the next time the counter is 0. 1 Globally Synchronized Updates to the register are delayed until the next time the counter is 0 after a synchronous update has been requested through the PWMCTL register. 3 LOADUPD R/W 0 Load Register Update Mode Value Description 0 Locally Synchronized Updates to the PWMnLOAD register are reflected to the generator the next time the counter is 0. 1 Globally Synchronized Updates to the register are delayed until the next time the counter is 0 after a synchronous update has been requested through the PWMCTL register. November 08, 2011 1297 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 2 DEBUG R/W 0 Description Debug Mode Value Description 1 MODE R/W 0 0 The counter stops running when it next reaches 0 and continues running again when no longer in Debug mode. 1 The counter always runs when in Debug mode. Counter Mode Value Description 0 ENABLE R/W 0 0 The counter counts down from the load value to 0 and then wraps back to the load value (Count-Down mode). 1 The counter counts up from 0 to the load value, back down to 0, and then repeats (Count-Up/Down mode). PWM Block Enable Value Description 0 The entire PWM generation block is disabled and not clocked. 1 The PWM generation block is enabled and produces PWM signals. 1298 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 16: PWM0 Interrupt and Trigger Enable (PWM0INTEN), offset 0x044 Register 17: PWM1 Interrupt and Trigger Enable (PWM1INTEN), offset 0x084 Register 18: PWM2 Interrupt and Trigger Enable (PWM2INTEN), offset 0x0C4 Register 19: PWM3 Interrupt and Trigger Enable (PWM3INTEN), offset 0x104 These registers control the interrupt and ADC trigger generation capabilities of the PWM generators (PWM0INTEN controls the PWM generator 0 block, and so on). The events that can cause an interrupt, or an ADC trigger are: ■ The counter being equal to the load register ■ The counter being equal to zero ■ The counter being equal to the PWMnCMPA register while counting up ■ The counter being equal to the PWMnCMPA register while counting down ■ The counter being equal to the PWMnCMPB register while counting up ■ The counter being equal to the PWMnCMPB register while counting down Any combination of these events can generate either an interrupt or an ADC trigger, though no determination can be made as to the actual event that caused an ADC trigger if more than one is specified. The PWMnRIS register provides information about which events have caused raw interrupts. PWM0 Interrupt and Trigger Enable (PWM0INTEN) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x044 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 5 4 3 2 1 0 reserved Type Reset RO 0 RO 0 15 14 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 13 12 11 10 9 8 7 6 TRCMPBD TRCMPBU TRCMPAD TRCMPAU TRCNTLOAD TRCNTZERO RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved RO 0 RO 0 INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:14 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 13 TRCMPBD R/W 0 Trigger for Counter=PWMnCMPB Down Value Description 1 An ADC trigger pulse is output when the counter matches the value in the PWMnCMPB register value while counting down. 0 No ADC trigger is output. November 08, 2011 1299 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 12 TRCMPBU R/W 0 Description Trigger for Counter=PWMnCMPB Up Value Description 11 TRCMPAD R/W 0 1 An ADC trigger pulse is output when the counter matches the value in the PWMnCMPB register value while counting up. 0 No ADC trigger is output. Trigger for Counter=PWMnCMPA Down Value Description 10 TRCMPAU R/W 0 1 An ADC trigger pulse is output when the counter matches the value in the PWMnCMPA register value while counting down. 0 No ADC trigger is output. Trigger for Counter=PWMnCMPA Up Value Description 9 TRCNTLOAD R/W 0 1 An ADC trigger pulse is output when the counter matches the value in the PWMnCMPA register value while counting up. 0 No ADC trigger is output. Trigger for Counter=PWMnLOAD Value Description 8 TRCNTZERO R/W 0 1 An ADC trigger pulse is output when the counter matches the PWMnLOAD register. 0 No ADC trigger is output. Trigger for Counter=0 Value Description 7:6 reserved RO 0x0 5 INTCMPBD R/W 0 1 An ADC trigger pulse is output when the counter is 0. 0 No ADC trigger is output. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Interrupt for Counter=PWMnCMPB Down Value Description 1 A raw interrupt occurs when the counter matches the value in the PWMnCMPB register value while counting down. 0 No interrupt. 1300 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 4 INTCMPBU R/W 0 Description Interrupt for Counter=PWMnCMPB Up Value Description 3 INTCMPAD R/W 0 1 A raw interrupt occurs when the counter matches the value in the PWMnCMPB register value while counting up. 0 No interrupt. Interrupt for Counter=PWMnCMPA Down Value Description 2 INTCMPAU R/W 0 1 A raw interrupt occurs when the counter matches the value in the PWMnCMPA register value while counting down. 0 No interrupt. Interrupt for Counter=PWMnCMPA Up Value Description 1 INTCNTLOAD R/W 0 1 A raw interrupt occurs when the counter matches the value in the PWMnCMPA register value while counting up. 0 No interrupt. Interrupt for Counter=PWMnLOAD Value Description 0 INTCNTZERO R/W 0 1 A raw interrupt occurs when the counter matches the value in the PWMnLOAD register value. 0 No interrupt. Interrupt for Counter=0 Value Description 1 A raw interrupt occurs when the counter is zero. 0 No interrupt. November 08, 2011 1301 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 20: PWM0 Raw Interrupt Status (PWM0RIS), offset 0x048 Register 21: PWM1 Raw Interrupt Status (PWM1RIS), offset 0x088 Register 22: PWM2 Raw Interrupt Status (PWM2RIS), offset 0x0C8 Register 23: PWM3 Raw Interrupt Status (PWM3RIS), offset 0x108 These registers provide the current set of interrupt sources that are asserted, regardless of whether they cause an interrupt to be asserted to the controller (PWM0RIS controls the PWM generator 0 block, and so on). If a bit is set, the event has occurred; if a bit is clear, the event has not occurred. Bits in this register are cleared by writing a 1 to the corresponding bit in the PWMnISC register. PWM0 Raw Interrupt Status (PWM0RIS) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x048 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved Type Reset reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:6 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5 INTCMPBD RO 0 Comparator B Down Interrupt Status Value Description 1 The counter has matched the value in the PWMnCMPB register while counting down. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTCMPBD bit in the PWMnISC register. 4 INTCMPBU RO 0 Comparator B Up Interrupt Status Value Description 1 The counter has matched the value in the PWMnCMPB register while counting up. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTCMPBU bit in the PWMnISC register. 1302 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 3 INTCMPAD RO 0 Description Comparator A Down Interrupt Status Value Description 1 The counter has matched the value in the PWMnCMPA register while counting down. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTCMPAD bit in the PWMnISC register. 2 INTCMPAU RO 0 Comparator A Up Interrupt Status Value Description 1 The counter has matched the value in the PWMnCMPA register while counting up. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTCMPAU bit in the PWMnISC register. 1 INTCNTLOAD RO 0 Counter=Load Interrupt Status Value Description 1 The counter has matched the value in the PWMnLOAD register. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTCNTLOAD bit in the PWMnISC register. 0 INTCNTZERO RO 0 Counter=0 Interrupt Status Value Description 1 The counter has matched zero. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTCNTZERO bit in the PWMnISC register. November 08, 2011 1303 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 24: PWM0 Interrupt Status and Clear (PWM0ISC), offset 0x04C Register 25: PWM1 Interrupt Status and Clear (PWM1ISC), offset 0x08C Register 26: PWM2 Interrupt Status and Clear (PWM2ISC), offset 0x0CC Register 27: PWM3 Interrupt Status and Clear (PWM3ISC), offset 0x10C These registers provide the current set of interrupt sources that are asserted to the interrupt controller (PWM0ISC controls the PWM generator 0 block, and so on). A bit is set if the event has occurred and is enabled in the PWMnINTEN register; if a bit is clear, the event has not occurred or is not enabled. These are R/W1C registers; writing a 1 to a bit position clears the corresponding interrupt reason. PWM0 Interrupt Status and Clear (PWM0ISC) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x04C Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved Type Reset reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO RO 0 RO 0 RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 Bit/Field Name Type Reset Description 31:6 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5 INTCMPBD R/W1C 0 Comparator B Down Interrupt Value Description 1 The INTCMPBD bits in the PWMnRIS and PWMnINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTCMPBD bit in the PWMnRIS register. 4 INTCMPBU R/W1C 0 Comparator B Up Interrupt Value Description 1 The INTCMPBU bits in the PWMnRIS and PWMnINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTCMPBU bit in the PWMnRIS register. 1304 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 3 INTCMPAD R/W1C 0 Description Comparator A Down Interrupt Value Description 1 The INTCMPAD bits in the PWMnRIS and PWMnINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTCMPAD bit in the PWMnRIS register. 2 INTCMPAU R/W1C 0 Comparator A Up Interrupt Value Description 1 The INTCMPAU bits in the PWMnRIS and PWMnINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTCMPAU bit in the PWMnRIS register. 1 INTCNTLOAD R/W1C 0 Counter=Load Interrupt Value Description 1 The INTCNTLOAD bits in the PWMnRIS and PWMnINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTCNTLOAD bit in the PWMnRIS register. 0 INTCNTZERO R/W1C 0 Counter=0 Interrupt Value Description 1 The INTCNTZERO bits in the PWMnRIS and PWMnINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTCNTZERO bit in the PWMnRIS register. November 08, 2011 1305 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 28: PWM0 Load (PWM0LOAD), offset 0x050 Register 29: PWM1 Load (PWM1LOAD), offset 0x090 Register 30: PWM2 Load (PWM2LOAD), offset 0x0D0 Register 31: PWM3 Load (PWM3LOAD), offset 0x110 These registers contain the load value for the PWM counter (PWM0LOAD controls the PWM generator 0 block, and so on). Based on the counter mode configured by the MODE bit in the PWMnCTL register, this value is either loaded into the counter after it reaches zero or is the limit of up-counting after which the counter decrements back to zero. When this value matches the counter, a pulse is output which can be configured to drive the generation of the pwmA and/or pwmB signal (via the PWMnGENA/PWMnGENB register) or drive an interruptor ADC trigger (via the PWMnINTEN register). If the Load Value Update mode is locally synchronized (based on the LOADUPD field encoding in the PWMnCTL register), the 16-bit LOAD value is used the next time the counter reaches zero. If the update mode is globally synchronized, it is used the next time the counter reaches zero after a synchronous update has been requested through the PWM Master Control (PWMCTL) register (see page 1269). If this register is re-written before the actual update occurs, the previous value is never used and is lost. PWM0 Load (PWM0LOAD) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x050 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 LOAD Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 LOAD R/W 0x0000 Counter Load Value The counter load value. 1306 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 32: PWM0 Counter (PWM0COUNT), offset 0x054 Register 33: PWM1 Counter (PWM1COUNT), offset 0x094 Register 34: PWM2 Counter (PWM2COUNT), offset 0x0D4 Register 35: PWM3 Counter (PWM3COUNT), offset 0x114 These registers contain the current value of the PWM counter (PWM0COUNT is the value of the PWM generator 0 block, and so on). When this value matches zero or the value in the PWMnLOAD, PWMnCMPA, or PWMnCMPB registers, a pulse is output which can be configured to drive the generation of a PWM signal or drive an interrupt or ADC trigger. PWM0 Counter (PWM0COUNT) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x054 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset COUNT Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 COUNT RO 0x0000 Counter Value The current value of the counter. November 08, 2011 1307 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 36: PWM0 Compare A (PWM0CMPA), offset 0x058 Register 37: PWM1 Compare A (PWM1CMPA), offset 0x098 Register 38: PWM2 Compare A (PWM2CMPA), offset 0x0D8 Register 39: PWM3 Compare A (PWM3CMPA), offset 0x118 These registers contain a value to be compared against the counter (PWM0CMPA controls the PWM generator 0 block, and so on). When this value matches the counter, a pulse is output which can be configured to drive the generation of the pwmA and pwmB signals (via the PWMnGENA and PWMnGENB registers) or drive an interrupt or ADC trigger (via the PWMnINTEN register). If the value of this register is greater than the PWMnLOAD register (see page 1306), then no pulse is ever output. If the comparator A update mode is locally synchronized (based on the CMPAUPD bit in the PWMnCTL register), the 16-bit COMPA value is used the next time the counter reaches zero. If the update mode is globally synchronized, it is used the next time the counter reaches zero after a synchronous update has been requested through the PWM Master Control (PWMCTL) register (see page 1269). If this register is rewritten before the actual update occurs, the previous value is never used and is lost. PWM0 Compare A (PWM0CMPA) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x058 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 COMPA Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 COMPA R/W 0x00 Comparator A Value The value to be compared against the counter. 1308 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 40: PWM0 Compare B (PWM0CMPB), offset 0x05C Register 41: PWM1 Compare B (PWM1CMPB), offset 0x09C Register 42: PWM2 Compare B (PWM2CMPB), offset 0x0DC Register 43: PWM3 Compare B (PWM3CMPB), offset 0x11C These registers contain a value to be compared against the counter (PWM0CMPB controls the PWM generator 0 block, and so on). When this value matches the counter, a pulse is output which can be configured to drive the generation of the pwmA and pwmB signals (via the PWMnGENA and PWMnGENB registers) or drive an interrupt or ADC trigger (via the PWMnINTEN register). If the value of this register is greater than the PWMnLOAD register, no pulse is ever output. If the comparator B update mode is locally synchronized (based on the CMPBUPD bit in the PWMnCTL register), the 16-bit COMPB value is used the next time the counter reaches zero. If the update mode is globally synchronized, it is used the next time the counter reaches zero after a synchronous update has been requested through the PWM Master Control (PWMCTL) register (see page 1269). If this register is rewritten before the actual update occurs, the previous value is never used and is lost. PWM0 Compare B (PWM0CMPB) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x05C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 COMPB Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 COMPB R/W 0x0000 Comparator B Value The value to be compared against the counter. November 08, 2011 1309 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 44: PWM0 Generator A Control (PWM0GENA), offset 0x060 Register 45: PWM1 Generator A Control (PWM1GENA), offset 0x0A0 Register 46: PWM2 Generator A Control (PWM2GENA), offset 0x0E0 Register 47: PWM3 Generator A Control (PWM3GENA), offset 0x120 These registers control the generation of the pwmA signal based on the load and zero output pulses from the counter, as well as the compare A and compare B pulses from the comparators (PWM0GENA controls the PWM generator 0 block, and so on). When the counter is running in Count-Down mode, only four of these events occur; when running in Count-Up/Down mode, all six occur. These events provide great flexibility in the positioning and duty cycle of the resulting PWM signal. The PWM0GENA register controls generation of the pwm0A signal; PWM1GENA, the pwm1A signal; PWM2GENA, the pwm2A signal; and PWM3GENA, the pwm3A signal. If a zero or load event coincides with a compare A or compare B event, the zero or load action is taken and the compare A or compare B action is ignored. If a compare A event coincides with a compare B event, the compare A action is taken and the compare B action is ignored. If the Generator A update mode is immediate (based on the GENAUPD field encoding in the PWMnCTL register), the ACTCMPBD, ACTCMPBU, ACTCMPAD, ACTCMPAU, ACTLOAD, and ACTZERO values are used immediately. If the update mode is locally synchronized, these values are used the next time the counter reaches zero. If the update mode is globally synchronized, these values are used the next time the counter reaches zero after a synchronous update has been requested through the PWM Master Control (PWMCTL) register (see page 1269). If this register is rewritten before the actual update occurs, the previous value is never used and is lost. PWM0 Generator A Control (PWM0GENA) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x060 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 reserved Type Reset RO 0 RO 0 ACTCMPBD RO 0 RO 0 R/W 0 R/W 0 RO 0 RO 0 9 8 ACTCMPBU R/W 0 Bit/Field Name Type Reset 31:12 reserved RO 0x0000.0 R/W 0 ACTCMPAD R/W 0 R/W 0 ACTCMPAU R/W 0 R/W 0 ACTLOAD R/W 0 R/W 0 ACTZERO R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1310 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 11:10 ACTCMPBD R/W 0x0 Description Action for Comparator B Down This field specifies the action to be taken when the counter matches comparator B while counting down. Value Description 9:8 ACTCMPBU R/W 0x0 0x0 Do nothing. 0x1 Invert pwmA. 0x2 Drive pwmA Low. 0x3 Drive pwmA High. Action for Comparator B Up This field specifies the action to be taken when the counter matches comparator B while counting up. This action can only occur when the MODE bit in the PWMnCTL register is set. Value Description 7:6 ACTCMPAD R/W 0x0 0x0 Do nothing. 0x1 Invert pwmA. 0x2 Drive pwmA Low. 0x3 Drive pwmA High. Action for Comparator A Down This field specifies the action to be taken when the counter matches comparator A while counting down. Value Description 5:4 ACTCMPAU R/W 0x0 0x0 Do nothing. 0x1 Invert pwmA. 0x2 Drive pwmA Low. 0x3 Drive pwmA High. Action for Comparator A Up This field specifies the action to be taken when the counter matches comparator A while counting up. This action can only occur when the MODE bit in the PWMnCTL register is set. Value Description 0x0 Do nothing. 0x1 Invert pwmA. 0x2 Drive pwmA Low. 0x3 Drive pwmA High. November 08, 2011 1311 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 3:2 ACTLOAD R/W 0x0 Description Action for Counter=LOAD This field specifies the action to be taken when the counter matches the value in the PWMnLOAD register. Value Description 1:0 ACTZERO R/W 0x0 0x0 Do nothing. 0x1 Invert pwmA. 0x2 Drive pwmA Low. 0x3 Drive pwmA High. Action for Counter=0 This field specifies the action to be taken when the counter is zero. Value Description 0x0 Do nothing. 0x1 Invert pwmA. 0x2 Drive pwmA Low. 0x3 Drive pwmA High. 1312 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 48: PWM0 Generator B Control (PWM0GENB), offset 0x064 Register 49: PWM1 Generator B Control (PWM1GENB), offset 0x0A4 Register 50: PWM2 Generator B Control (PWM2GENB), offset 0x0E4 Register 51: PWM3 Generator B Control (PWM3GENB), offset 0x124 These registers control the generation of the pwmB signal based on the load and zero output pulses from the counter, as well as the compare A and compare B pulses from the comparators (PWM0GENB controls the PWM generator 0 block, and so on). When the counter is running in Count-Down mode, only four of these events occur; when running in Count-Up/Down mode, all six occur. These events provide great flexibility in the positioning and duty cycle of the resulting PWM signal. The PWM0GENB register controls generation of the pwm0B signal; PWM1GENB, the pwm1B signal; PWM2GENB, the pwm2B signal; and PWM3GENB, the pwm3B signal. If a zero or load event coincides with a compare A or compare B event, the zero or load action is taken and the compare A or compare B action is ignored. If a compare A event coincides with a compare B event, the compare B action is taken and the compare A action is ignored. If the Generator B update mode is immediate (based on the GENBUPD field encoding in the PWMnCTL register), the ACTCMPBD, ACTCMPBU, ACTCMPAD, ACTCMPAU, ACTLOAD, and ACTZERO values are used immediately. If the update mode is locally synchronized, these values are used the next time the counter reaches zero. If the update mode is globally synchronized, these values are used the next time the counter reaches zero after a synchronous update has been requested through the PWM Master Control (PWMCTL) register (see page 1269). If this register is rewritten before the actual update occurs, the previous value is never used and is lost. PWM0 Generator B Control (PWM0GENB) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x064 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 reserved Type Reset RO 0 RO 0 ACTCMPBD RO 0 RO 0 R/W 0 R/W 0 RO 0 RO 0 9 8 ACTCMPBU R/W 0 Bit/Field Name Type Reset 31:12 reserved RO 0x0000.0 R/W 0 ACTCMPAD R/W 0 R/W 0 ACTCMPAU R/W 0 R/W 0 ACTLOAD R/W 0 R/W 0 ACTZERO R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. November 08, 2011 1313 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 11:10 ACTCMPBD R/W 0x0 Description Action for Comparator B Down This field specifies the action to be taken when the counter matches comparator B while counting down. Value Description 9:8 ACTCMPBU R/W 0x0 0x0 Do nothing. 0x1 Invert pwmB. 0x2 Drive pwmB Low. 0x3 Drive pwmB High. Action for Comparator B Up This field specifies the action to be taken when the counter matches comparator B while counting up. This action can only occur when the MODE bit in the PWMnCTL register is set. Value Description 7:6 ACTCMPAD R/W 0x0 0x0 Do nothing. 0x1 Invert pwmB. 0x2 Drive pwmB Low. 0x3 Drive pwmB High. Action for Comparator A Down This field specifies the action to be taken when the counter matches comparator A while counting down. Value Description 5:4 ACTCMPAU R/W 0x0 0x0 Do nothing. 0x1 Invert pwmB. 0x2 Drive pwmB Low. 0x3 Drive pwmB High. Action for Comparator A Up This field specifies the action to be taken when the counter matches comparator A while counting up. This action can only occur when the MODE bit in the PWMnCTL register is set. Value Description 0x0 Do nothing. 0x1 Invert pwmB. 0x2 Drive pwmB Low. 0x3 Drive pwmB High. 1314 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 3:2 ACTLOAD R/W 0x0 Description Action for Counter=LOAD This field specifies the action to be taken when the counter matches the load value. Value Description 1:0 ACTZERO R/W 0x0 0x0 Do nothing. 0x1 Invert pwmB. 0x2 Drive pwmB Low. 0x3 Drive pwmB High. Action for Counter=0 This field specifies the action to be taken when the counter is 0. Value Description 0x0 Do nothing. 0x1 Invert pwmB. 0x2 Drive pwmB Low. 0x3 Drive pwmB High. November 08, 2011 1315 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 52: PWM0 Dead-Band Control (PWM0DBCTL), offset 0x068 Register 53: PWM1 Dead-Band Control (PWM1DBCTL), offset 0x0A8 Register 54: PWM2 Dead-Band Control (PWM2DBCTL), offset 0x0E8 Register 55: PWM3 Dead-Band Control (PWM3DBCTL), offset 0x128 The PWMnDBCTL register controls the dead-band generator, which produces the MnPWMn signals based on the pwmA and pwmB signals. When disabled, the pwmA signal passes through to the pwmA' signal and the pwmB signal passes through to the pwmB' signal. When dead-band control is enabled, the pwmB signal is ignored, the pwmA' signal is generated by delaying the rising edge(s) of the pwmA signal by the value in the PWMnDBRISE register (see page 1317), and the pwmB' signal is generated by inverting the pwmA signal and delaying the falling edge(s) of the pwmA signal by the value in the PWMnDBFALL register (see page 1318). The Output Control block outputs the pwm0A' signal on the MnPWM0 signal and the pwm0B' signal on the MnPWM1 signal. In a similar manner, MnPWM2 and MnPWM3 are produced from the pwm1A' and pwm1B' signals, MnPWM4 and MnPWM5 are produced from the pwm2A' and pwm2B' signals, and MnPWM6 and MnPWM7 are produced from the pwm3A' and pwm3B' signals. If the Dead-Band Control mode is immediate (based on the DBCTLUPD field encoding in the PWMnCTL register), the ENABLE bit value is used immediately. If the update mode is locally synchronized, this value is used the next time the counter reaches zero. If the update mode is globally synchronized, this value is used the next time the counter reaches zero after a synchronous update has been requested through the PWM Master Control (PWMCTL) register (see page 1269). If this register is rewritten before the actual update occurs, the previous value is never used and is lost. PWM0 Dead-Band Control (PWM0DBCTL) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x068 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 ENABLE R/W 0 RO 0 0 ENABLE RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Dead-Band Generator Enable Value Description 1 The dead-band generator modifies the pwmA signal by inserting dead bands into the pwmA' and pwmB' signals. 0 The pwmA and pwmB signals pass through to the pwmA' and pwmB' signals unmodified. 1316 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 56: PWM0 Dead-Band Rising-Edge Delay (PWM0DBRISE), offset 0x06C Register 57: PWM1 Dead-Band Rising-Edge Delay (PWM1DBRISE), offset 0x0AC Register 58: PWM2 Dead-Band Rising-Edge Delay (PWM2DBRISE), offset 0x0EC Register 59: PWM3 Dead-Band Rising-Edge Delay (PWM3DBRISE), offset 0x12C The PWMnDBRISE register contains the number of clock cycles to delay the rising edge of the pwmA signal when generating the pwmA' signal. If the dead-band generator is disabled through the PWMnDBCTL register, this register is ignored. If the value of this register is larger than the width of a High pulse on the pwmA signal, the rising-edge delay consumes the entire High time of the signal, resulting in no High time on the output. Care must be taken to ensure that the pwmA High time always exceeds the rising-edge delay. If the Dead-Band Rising-Edge Delay mode is immediate (based on the DBRISEUPD field encoding in the PWMnCTL register), the 12-bit RISEDELAY value is used immediately. If the update mode is locally synchronized, this value is used the next time the counter reaches zero. If the update mode is globally synchronized, this value is used the next time the counter reaches zero after a synchronous update has been requested through the PWM Master Control (PWMCTL) register (see page 1269). If this register is rewritten before the actual update occurs, the previous value is never used and is lost. PWM0 Dead-Band Rising-Edge Delay (PWM0DBRISE) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x06C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 reserved Type Reset RO 0 RO 0 RISEDELAY RO 0 RO 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:12 reserved RO 0x0000.0 11:0 RISEDELAY R/W 0x000 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Dead-Band Rise Delay The number of clock cycles to delay the rising edge of pwmA' after the rising edge of pwmA. November 08, 2011 1317 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 60: PWM0 Dead-Band Falling-Edge-Delay (PWM0DBFALL), offset 0x070 Register 61: PWM1 Dead-Band Falling-Edge-Delay (PWM1DBFALL), offset 0x0B0 Register 62: PWM2 Dead-Band Falling-Edge-Delay (PWM2DBFALL), offset 0x0F0 Register 63: PWM3 Dead-Band Falling-Edge-Delay (PWM3DBFALL), offset 0x130 The PWMnDBFALL register contains the number of clock cycles to delay the rising edge of the pwmB' signal from the falling edge of the pwmA signal. If the dead-band generator is disabled through the PWMnDBCTL register, this register is ignored. If the value of this register is larger than the width of a Low pulse on the pwmA signal, the falling-edge delay consumes the entire Low time of the signal, resulting in no Low time on the output. Care must be taken to ensure that the pwmA Low time always exceeds the falling-edge delay. If the Dead-Band Falling-Edge-Delay mode is immediate (based on the DBFALLUP field encoding in the PWMnCTL register), the 12-bit FALLDELAY value is used immediately. If the update mode is locally synchronized, this value is used the next time the counter reaches zero. If the update mode is globally synchronized, this value is used the next time the counter reaches zero after a synchronous update has been requested through the PWM Master Control (PWMCTL) register (see page 1269). If this register is rewritten before the actual update occurs, the previous value is never used and is lost. PWM0 Dead-Band Falling-Edge-Delay (PWM0DBFALL) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x070 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 reserved Type Reset RO 0 RO 0 FALLDELAY RO 0 RO 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:12 reserved RO 0x0000.0 11:0 FALLDELAY R/W 0x000 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Dead-Band Fall Delay The number of clock cycles to delay the falling edge of pwmB' from the rising edge of pwmA. 1318 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 64: PWM0 Fault Source 0 (PWM0FLTSRC0), offset 0x074 Register 65: PWM1 Fault Source 0 (PWM1FLTSRC0), offset 0x0B4 Register 66: PWM2 Fault Source 0 (PWM2FLTSRC0), offset 0x0F4 Register 67: PWM3 Fault Source 0 (PWM3FLTSRC0), offset 0x134 This register specifies which fault pin inputs are used to generate a fault condition. Each bit in the following register indicates whether the corresponding fault pin is included in the fault condition. All enabled fault pins are ORed together to form the PWMnFLTSRC0 portion of the fault condition. The PWMnFLTSRC0 fault condition is then ORed with the PWMnFLTSRC1 fault condition to generate the final fault condition for the PWM generator. If the FLTSRC bit in the PWMnCTL register (see page 1294) is clear, only the Fault0 signal affects the fault condition generated. Otherwise, sources defined in PWMnFLTSRC0 and PWMnFLTSRC1 affect the fault condition generated. PWM0 Fault Source 0 (PWM0FLTSRC0) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x074 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:4 reserved RO 0x0000 3 FAULT3 R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 FAULT3 FAULT2 FAULT1 FAULT0 R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Fault3 Input Value Description 0 The Fault3 signal is suppressed and cannot generate a fault condition. 1 The Fault3 signal value is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. November 08, 2011 1319 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 2 FAULT2 R/W 0 Description Fault2 Input Value Description 0 The Fault2 signal is suppressed and cannot generate a fault condition. 1 The Fault2 signal value is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: 1 FAULT1 R/W 0 The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. Fault1 Input Value Description 0 The Fault1 signal is suppressed and cannot generate a fault condition. 1 The Fault1 signal value is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: 0 FAULT0 R/W 0 The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. Fault0 Input Value Description 0 The Fault0 signal is suppressed and cannot generate a fault condition. 1 The Fault0 signal value is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. 1320 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 68: PWM0 Fault Source 1 (PWM0FLTSRC1), offset 0x078 Register 69: PWM1 Fault Source 1 (PWM1FLTSRC1), offset 0x0B8 Register 70: PWM2 Fault Source 1 (PWM2FLTSRC1), offset 0x0F8 Register 71: PWM3 Fault Source 1 (PWM3FLTSRC1), offset 0x138 This register specifies which digital comparator triggers from the ADC are used to generate a fault condition. Each bit in the following register indicates whether the corresponding digital comparator trigger is included in the fault condition. All enabled digital comparator triggers are ORed together to form the PWMnFLTSRC1 portion of the fault condition. The PWMnFLTSRC1 fault condition is then ORed with the PWMnFLTSRC0 fault condition to generate the final fault condition for the PWM generator. If the FLTSRC bit in the PWMnCTL register (see page 1294) is clear, only the PWM Fault0 pin affects the fault condition generated. Otherwise, sources defined in PWMnFLTSRC0 and PWMnFLTSRC1 affect the fault condition generated. PWM0 Fault Source 1 (PWM0FLTSRC1) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x078 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 DCMP7 R/W 0 RO 0 7 6 5 4 3 2 1 0 DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Digital Comparator 7 Value Description 0 The trigger from digital comparator 7 is suppressed and cannot generate a fault condition. 1 The trigger from digital comparator 7 is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. November 08, 2011 1321 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 6 DCMP6 R/W 0 Description Digital Comparator 6 Value Description 0 The trigger from digital comparator 6 is suppressed and cannot generate a fault condition. 1 The trigger from digital comparator 6 is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: 5 DCMP5 R/W 0 The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. Digital Comparator 5 Value Description 0 The trigger from digital comparator 5 is suppressed and cannot generate a fault condition. 1 The trigger from digital comparator 5 is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: 4 DCMP4 R/W 0 The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. Digital Comparator 4 Value Description 0 The trigger from digital comparator 4 is suppressed and cannot generate a fault condition. 1 The trigger from digital comparator 4 is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: 3 DCMP3 R/W 0 The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. Digital Comparator 3 Value Description 0 The trigger from digital comparator 3 is suppressed and cannot generate a fault condition. 1 The trigger from digital comparator 3 is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. 1322 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 2 DCMP2 R/W 0 Description Digital Comparator 2 Value Description 0 The trigger from digital comparator 2 is suppressed and cannot generate a fault condition. 1 The trigger from digital comparator 2 is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: 1 DCMP1 R/W 0 The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. Digital Comparator 1 Value Description 0 The trigger from digital comparator 1 is suppressed and cannot generate a fault condition. 1 The trigger from digital comparator 1 is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: 0 DCMP0 R/W 0 The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. Digital Comparator 0 Value Description 0 The trigger from digital comparator 0 is suppressed and cannot generate a fault condition. 1 The trigger from digital comparator 0 is ORed with all other fault condition generation inputs (Faultn signals and digital comparators). Note: The FLTSRC bit in the PWMnCTL register must be set for this bit to affect fault condition generation. November 08, 2011 1323 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 72: PWM0 Minimum Fault Period (PWM0MINFLTPER), offset 0x07C Register 73: PWM1 Minimum Fault Period (PWM1MINFLTPER), offset 0x0BC Register 74: PWM2 Minimum Fault Period (PWM2MINFLTPER), offset 0x0FC Register 75: PWM3 Minimum Fault Period (PWM3MINFLTPER), offset 0x13C If the MINFLTPER bit in the PWMnCTL register is set, this register specifies the 16-bit time-extension value to be used in extending the fault condition. The value is loaded into a 16-bit down counter, and the counter value is used to extend the fault condition. The fault condition is released in the clock immediately after the counter value reaches 0. The fault condition is asynchronous to the PWM clock; and the delay value is the product of the PWM clock period and the (MFP field value + 1) or (MFP field value + 2) depending on when the fault condition asserts with respect to the PWM clock. The counter decrements at the PWM clock rate, without pause or condition. PWM0 Minimum Fault Period (PWM0MINFLTPER) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x07C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset MFP Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 MFP R/W 0x0000 Minimum Fault Period The number of PWM clocks by which a fault condition is extended when the delay is enabled by PWMnCTL MINFLTPER. 1324 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 76: PWM0 Fault Pin Logic Sense (PWM0FLTSEN), offset 0x800 Register 77: PWM1 Fault Pin Logic Sense (PWM1FLTSEN), offset 0x880 Register 78: PWM2 Fault Pin Logic Sense (PWM2FLTSEN), offset 0x900 Register 79: PWM3 Fault Pin Logic Sense (PWM3FLTSEN), offset 0x980 This register defines the PWM fault pin logic sense. PWM0 Fault Pin Logic Sense (PWM0FLTSEN) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x800 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 FAULT3 FAULT2 FAULT1 FAULT0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 FAULT3 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Fault3 Sense Value Description 2 FAULT2 R/W 0 0 An error is indicated if the Fault3 signal is High. 1 An error is indicated if the Fault3 signal is Low. Fault2 Sense Value Description 1 FAULT1 R/W 0 0 An error is indicated if the Fault2 signal is High. 1 An error is indicated if the Fault2 signal is Low. Fault1 Sense Value Description 0 FAULT0 R/W 0 0 An error is indicated if the Fault1 signal is High. 1 An error is indicated if the Fault1 signal is Low. Fault0 Sense Value Description 0 An error is indicated if the Fault0 signal is High. 1 An error is indicated if the Fault0 signal is Low. November 08, 2011 1325 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 80: PWM0 Fault Status 0 (PWM0FLTSTAT0), offset 0x804 Register 81: PWM1 Fault Status 0 (PWM1FLTSTAT0), offset 0x884 Register 82: PWM2 Fault Status 0 (PWM2FLTSTAT0), offset 0x904 Register 83: PWM3 Fault Status 0 (PWM3FLTSTAT0), offset 0x984 Along with the PWMnFLTSTAT1 register, this register provides status regarding the fault condition inputs. If the LATCH bit in the PWMnCTL register is clear, the contents of the PWMnFLTSTAT0 register are read-only (RO) and provide the current state of the MnFAULTn inputs. If the LATCH bit in the PWMnCTL register is set, the contents of the PWMnFLTSTAT0 register are read / write 1 to clear (R/W1C) and provide a latched version of the MnFAULTn inputs. In this mode, the register bits are cleared by writing a 1 to a set bit. The MnFAULTn inputs are recorded after their sense is adjusted in the generator. The contents of this register can only be written if the fault source extensions are enabled (the FLTSRC bit in the PWMnCTL register is set). PWM0 Fault Status 0 (PWM0FLTSTAT0) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x804 Type -, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:4 reserved RO 0x0000 3 FAULT3 - 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 FAULT3 FAULT2 FAULT1 FAULT0 0 0 0 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Fault Input 3 If the PWMnCTL register LATCH bit is clear, this bit is RO and represents the current state of the MnFAULT3 input signal after the logic sense adjustment. If the PWMnCTL register LATCH bit is set, this bit is R/W1C and represents a sticky version of the MnFAULT3 input signal after the logic sense adjustment. ■ If FAULT3 is set, the input transitioned to the active state previously. ■ If FAULT3 is clear, the input has not transitioned to the active state since the last time it was cleared. ■ The FAULT3 bit is cleared by writing it with the value 1. 1326 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset Description 2 FAULT2 - 0 Fault Input 2 If the PWMnCTL register LATCH bit is clear, this bit is RO and represents the current state of the MnFAULT2 input signal after the logic sense adjustment. If the PWMnCTL register LATCH bit is set, this bit is R/W1C and represents a sticky version of the MnFAULT2 input signal after the logic sense adjustment. 1 FAULT1 - 0 ■ If FAULT2 is set, the input transitioned to the active state previously. ■ If FAULT2 is clear, the input has not transitioned to the active state since the last time it was cleared. ■ The FAULT2 bit is cleared by writing it with the value 1. Fault Input 1 If the PWMnCTL register LATCH bit is clear, this bit is RO and represents the current state of the MnFAULT1 input signal after the logic sense adjustment. If the PWMnCTL register LATCH bit is set, this bit is R/W1C and represents a sticky version of the MnFAULT1 input signal after the logic sense adjustment. 0 FAULT0 - 0 ■ If FAULT1 is set, the input transitioned to the active state previously. ■ If FAULT1 is clear, the input has not transitioned to the active state since the last time it was cleared. ■ The FAULT1 bit is cleared by writing it with the value 1. Fault Input 0 If the PWMnCTL register LATCH bit is clear, this bit is RO and represents the current state of the input signal after the logic sense adjustment. If the PWMnCTL register LATCH bit is set, this bit is R/W1C and represents a sticky version of the input signal after the logic sense adjustment. ■ If FAULT0 is set, the input transitioned to the active state previously. ■ If FAULT0 is clear, the input has not transitioned to the active state since the last time it was cleared. ■ The FAULT0 bit is cleared by writing it with the value 1. November 08, 2011 1327 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Register 84: PWM0 Fault Status 1 (PWM0FLTSTAT1), offset 0x808 Register 85: PWM1 Fault Status 1 (PWM1FLTSTAT1), offset 0x888 Register 86: PWM2 Fault Status 1 (PWM2FLTSTAT1), offset 0x908 Register 87: PWM3 Fault Status 1 (PWM3FLTSTAT1), offset 0x988 Along with the PWMnFLTSTAT0 register, this register provides status regarding the fault condition inputs. If the LATCH bit in the PWMnCTL register is clear, the contents of the PWMnFLTSTAT1 register are read-only (RO) and provide the current state of the digital comparator triggers. If the LATCH bit in the PWMnCTL register is set, the contents of the PWMnFLTSTAT1 register are read / write 1 to clear (R/W1C) and provide a latched version of the digital comparator triggers. In this mode, the register bits are cleared by writing a 1 to a set bit. The contents of this register can only be written if the fault source extensions are enabled (the FLTSRC bit in the PWMnCTL register is set). PWM0 Fault Status 1 (PWM0FLTSTAT1) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0x808 Type -, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 0 0 0 0 0 0 0 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7 DCMP7 - 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Digital Comparator 7 Trigger If the PWMnCTL register LATCH bit is clear, this bit represents the current state of the Digital Comparator 7 trigger input. If the PWMnCTL register LATCH bit is set, this bit represents a sticky version of the trigger. ■ If DCMP7 is set, the trigger transitioned to the active state previously. ■ If DCMP7 is clear, the trigger has not transitioned to the active state since the last time it was cleared. ■ The DCMP7 bit is cleared by writing it with the value 1. 1328 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 6 DCMP6 - 0 Description Digital Comparator 6 Trigger If the PWMnCTL register LATCH bit is clear, this bit represents the current state of the Digital Comparator 6 trigger input. If the PWMnCTL register LATCH bit is set, this bit represents a sticky version of the trigger. 5 DCMP5 - 0 ■ If DCMP6 is set, the trigger transitioned to the active state previously. ■ If DCMP6 is clear, the trigger has not transitioned to the active state since the last time it was cleared. ■ The DCMP6 bit is cleared by writing it with the value 1. Digital Comparator 5 Trigger If the PWMnCTL register LATCH bit is clear, this bit represents the current state of the Digital Comparator 5 trigger input. If the PWMnCTL register LATCH bit is set, this bit represents a sticky version of the trigger. 4 DCMP4 - 0 ■ If DCMP5 is set, the trigger transitioned to the active state previously. ■ If DCMP5 is clear, the trigger has not transitioned to the active state since the last time it was cleared. ■ The DCMP5 bit is cleared by writing it with the value 1. Digital Comparator 4 Trigger If the PWMnCTL register LATCH bit is clear, this bit represents the current state of the Digital Comparator 4 trigger input. If the PWMnCTL register LATCH bit is set, this bit represents a sticky version of the trigger. 3 DCMP3 - 0 ■ If DCMP4 is set, the trigger transitioned to the active state previously. ■ If DCMP4 is clear, the trigger has not transitioned to the active state since the last time it was cleared. ■ The DCMP4 bit is cleared by writing it with the value 1. Digital Comparator 3 Trigger If the PWMnCTL register LATCH bit is clear, this bit represents the current state of the Digital Comparator 3 trigger input. If the PWMnCTL register LATCH bit is set, this bit represents a sticky version of the trigger. ■ If DCMP3 is set, the trigger transitioned to the active state previously. ■ If DCMP3 is clear, the trigger has not transitioned to the active state since the last time it was cleared. ■ The DCMP3 bit is cleared by writing it with the value 1. November 08, 2011 1329 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset 2 DCMP2 - 0 Description Digital Comparator 2 Trigger If the PWMnCTL register LATCH bit is clear, this bit represents the current state of the Digital Comparator 2 trigger input. If the PWMnCTL register LATCH bit is set, this bit represents a sticky version of the trigger. 1 DCMP1 - 0 ■ If DCMP2 is set, the trigger transitioned to the active state previously. ■ If DCMP2 is clear, the trigger has not transitioned to the active state since the last time it was cleared. ■ The DCMP2 bit is cleared by writing it with the value 1. Digital Comparator 1 Trigger If the PWMnCTL register LATCH bit is clear, this bit represents the current state of the Digital Comparator 1 trigger input. If the PWMnCTL register LATCH bit is set, this bit represents a sticky version of the trigger. 0 DCMP0 - 0 ■ If DCMP1 is set, the trigger transitioned to the active state previously. ■ If DCMP1 is clear, the trigger has not transitioned to the active state since the last time it was cleared. ■ The DCMP1 bit is cleared by writing it with the value 1. Digital Comparator 0 Trigger If the PWMnCTL register LATCH bit is clear, this bit represents the current state of the Digital Comparator 0 trigger input. If the PWMnCTL register LATCH bit is set, this bit represents a sticky version of the trigger. ■ If DCMP0 is set, the trigger transitioned to the active state previously. ■ If DCMP0 is clear, the trigger has not transitioned to the active state since the last time it was cleared. ■ The DCMP0 bit is cleared by writing it with the value 1. 1330 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 88: PWM Peripheral Properties (PWMPP), offset 0xFC0 The PWMPP register provides information regarding the properties of the PWM module. PWM Peripheral Properties (PWMPP) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0xFC0 Type RO, reset 0x0000.0344 31 30 29 28 27 26 25 24 0 0 0 0 0 0 0 0 15 14 13 12 11 10 9 8 ONE EFAULT ESYNC 0 0 0 0 RO 0 RO 1 RO 1 23 22 21 20 19 18 17 16 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 RO 0 RO 1 RO 0 RO 0 RO 0 RO 1 RO 0 RO 0 reserved Type Reset reserved Type Reset 0 FCNT GCNT Bit/Field Name Type Reset Description 31:11 reserved - 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 ONE RO 0x0 One-Shot Mode Value Description 9 EFAULT RO 0x1 1 One-shot modes are available. 0 One-shot modes are not available. Extended Fault Value Description 8 ESYNC RO 0x1 1 Extended fault capabilities are available. 0 Extended fault capabilities are not available. Extended Synchronization Value Description 7:4 FCNT RO 0x4 1 Extended synchronization is available. 0 Extended synchronization is not available. Fault Inputs Value Description 0x0 No fault inputs. 0x1 1 fault input. 0x2 2 fault input. 0x3 3 fault input. 0x4 4 fault input. 0x5 - 0xF reserved November 08, 2011 1331 Texas Instruments-Advance Information Pulse Width Modulator (PWM) Bit/Field Name Type Reset Description 3:0 GCNT RO 0x4 Generators Value Description 0x0 No generators. 0x1 1 generator 0x2 2 generators 0x3 3 generators 0x4 4 generators 0x5 - 0xF reserved The number of PWM outputs is 2 times the number of PWM generators. 1332 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 89: PWM Peripheral Configuration (PWMPC), offset 0xFC4 The PWMPC register provides information regarding the configuration of the PWM module.. PWM Peripheral Configuration (PWMPC) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 Offset 0xFC4 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 1 R/W 1 R/W 1 reserved Type Reset reserved Type Reset RO 0 PWMDIV USEPWMDIV Bit/Field Name Type Reset 31:9 reserved RO 0x0000.0 8 USEPWMDIV R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Enable PWM Clock Divisor Value Description 1 The PWM clock divider is the source for the PWM clock. 0 The system clock is the source for the PWM clock. This bit has the same function as the legacy USEPWMDIV bit in the RCC register. 7:0 PWMDIV R/W 0x7 PWM Clock Divisor This field specifies the binary divisor used to predivide the system clock down for use as the timing reference for the PWM module. The rising edge of this clock is synchronous with the system clock. Value Description 0x0 /2 0x1 /4 0x2 /8 0x3 /16 0x4 /32 0x5 /64 0x6 /64 0x7 /64 (default) 0x8 - 0xF reserved This bit has the same function as the legacy PWMDIV bit in the RCC register. November 08, 2011 1333 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) 21 Quadrature Encoder Interface (QEI) A quadrature encoder, also known as a 2-channel incremental encoder, converts linear displacement into a pulse signal. By monitoring both the number of pulses and the relative phase of the two signals, you can track the position, direction of rotation, and speed. In addition, a third channel, or index signal, can be used to reset the position counter. The LM4F232H5BB microcontroller includes two quadrature encoder interface (QEI) modules. Each QEI module interprets the code produced by a quadrature encoder wheel to integrate position over time and determine direction of rotation. In addition, it can capture a running estimate of the velocity of the encoder wheel. ® The Stellaris LM4F232H5BB microcontroller includes two QEI modules providing control of two motors at the same time with the following features: ■ Position integrator that tracks the encoder position ■ Programmable noise filter on the inputs ■ Velocity capture using built-in timer ■ The input frequency of the QEI inputs may be as high as 1/4 of the processor frequency (for example, 12.5 MHz for a 50-MHz system) ■ Interrupt generation on: – Index pulse – Velocity-timer expiration – Direction change – Quadrature error detection 21.1 Block Diagram Figure 21-1 on page 1335 provides a block diagram of a Stellaris QEI module. 1334 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 21-1. QEI Block Diagram QEILOAD Control & Status Velocity Timer QEITIME QEICTL QEISTAT Velocity Accumulator Velocity Predivider clk PhA PhB QEICOUNT QEISPEED QEIMAXPOS Quadrature Encoder dir Position Integrator QEIPOS IDX QEIINTEN Interrupt Control Interrupt QEIRIS QEIISC 21.2 Signal Description The following table lists the external signals of the QEI module and describes the function of each. The QEI signals are alternate functions for some GPIO signals and default to be GPIO signals at reset. The column in the table below titled "Pin Mux/Pin Assignment" lists the possible GPIO pin placements for these QEI signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 698) should be set to choose the QEI function. The number in parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control (GPIOPCTL) register (page 717) to assign the QEI signal to the specified GPIO port pin. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 674. Table 21-1. QEI Signals (157BGA) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description IDX0 C1 L9 K4 A9 PD3 (6) PF4 (6) PH1 (5) PJ2 (5) I TTL QEI module 0 index. IDX1 L2 L7 N3 PC4 (6) PG5 (6) PG7 (5) I TTL QEI module 1 index. PhA0 A3 M9 J3 PD6 (6) PF0 (6) PH4 (5) I TTL QEI module 0 phase A. PhA1 L1 L8 M7 PC5 (6) PG0 (6) PG3 (6) I TTL QEI module 1 phase A. November 08, 2011 1335 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Table 21-1. QEI Signals (157BGA) (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description PhB0 B3 N9 H4 PD7 (6) PF1 (6) PH5 (5) I TTL QEI module 0 phase B. PhB1 K1 K8 K7 PC6 (6) PG1 (6) PG4 (6) I TTL QEI module 1 phase B. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 21.3 Functional Description The QEI module interprets the two-bit gray code produced by a quadrature encoder wheel to integrate position over time and determine direction of rotation. In addition, it can capture a running estimate of the velocity of the encoder wheel. The position integrator and velocity capture can be independently enabled, though the position integrator must be enabled before the velocity capture can be enabled. The two phase signals, PhA and PhB, can be swapped before being interpreted by the QEI module to change the meaning of forward and backward and to correct for miswiring of the system. Alternatively, the phase signals can be interpreted as a clock and direction signal as output by some encoders. The QEI module input signals have a digital noise filter on them that can be enabled to prevent spurious operation. The noise filter requires that the inputs be stable for a specified number of consecutive clock cycles before updating the edge detector. The filter is enabled by the FILTEN bit in the QEI Control (QEICTL) register. The frequency of the input update is programmable using the FILTCNT bit field in the QEICTL register. The QEI module supports two modes of signal operation: quadrature phase mode and clock/direction mode. In quadrature phase mode, the encoder produces two clocks that are 90 degrees out of phase; the edge relationship is used to determine the direction of rotation. In clock/direction mode, the encoder produces a clock signal to indicate steps and a direction signal to indicate the direction of rotation. This mode is determined by the SIGMODE bit of the QEICTL register (see page 1340). When the QEI module is set to use the quadrature phase mode (SIGMODE bit is clear), the capture mode for the position integrator can be set to update the position counter on every edge of the PhA signal or to update on every edge of both PhA and PhB. Updating the position counter on every PhA and PhB edge provides more positional resolution at the cost of less range in the positional counter. When edges on PhA lead edges on PhB, the position counter is incremented. When edges on PhB lead edges on PhA, the position counter is decremented. When a rising and falling edge pair is seen on one of the phases without any edges on the other, the direction of rotation has changed. The positional counter is automatically reset on one of two conditions: sensing the index pulse or reaching the maximum position value. The reset mode is determined by the RESMODE bit of the QEICTL register. When RESMODE is set, the positional counter is reset when the index pulse is sensed. This mode limits the positional counter to the values [0:N-1], where N is the number of phase edges in a full revolution of the encoder wheel. The QEI Maximum Position (QEIMAXPOS) register must be programmed with N-1 so that the reverse direction from position 0 can move the position counter to N-1. In this mode, the position register contains the absolute position of the encoder relative to the index (or home) position once an index pulse has been seen. 1336 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller When RESMODE is clear, the positional counter is constrained to the range [0:M], where M is the programmable maximum value. The index pulse is ignored by the positional counter in this mode. Velocity capture uses a configurable timer and a count register. The timer counts the number of phase edges (using the same configuration as for the position integrator) in a given time period. The edge count from the previous time period is available to the controller via the QEI Velocity (QEISPEED) register, while the edge count for the current time period is being accumulated in the QEI Velocity Counter (QEICOUNT) register. As soon as the current time period is complete, the total number of edges counted in that time period is made available in the QEISPEED register (overwriting the previous value), the QEICOUNT register is cleared, and counting commences on a new time period. The number of edges counted in a given time period is directly proportional to the velocity of the encoder. Figure 21-2 on page 1337 shows how the Stellaris quadrature encoder converts the phase input signals into clock pulses, the direction signal, and how the velocity predivider operates (in Divide by 4 mode). Figure 21-2. Quadrature Encoder and Velocity Predivider Operation PhA PhB clk clkdiv dir pos rel -1 -1 -1 -1 -1 -1 -1 -1 -1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 +1 +1 +1 The period of the timer is configurable by specifying the load value for the timer in the QEI Timer Load (QEILOAD) register. When the timer reaches zero, an interrupt can be triggered, and the hardware reloads the timer with the QEILOAD value and continues to count down. At lower encoder speeds, a longer timer period is required to be able to capture enough edges to have a meaningful result. At higher encoder speeds, both a shorter timer period and/or the velocity predivider can be used. The following equation converts the velocity counter value into an rpm value: rpm = (clock * (2 ^ VELDIV) * SPEED * 60) ÷ (LOAD * ppr * edges) where: clock is the controller clock rate ppr is the number of pulses per revolution of the physical encoder edges is 2 or 4, based on the capture mode set in the QEICTL register (2 for CAPMODE clear and 4 for CAPMODE set) For example, consider a motor running at 600 rpm. A 2048 pulse per revolution quadrature encoder is attached to the motor, producing 8192 phase edges per revolution. With a velocity predivider of ÷1 (VELDIV is clear) and clocking on both PhA and PhB edges, this results in 81,920 pulses per second (the motor turns 10 times per second). If the timer were clocked at 10,000 Hz, and the load value was 2,500 (¼ of a second), it would count 20,480 pulses per update. Using the above equation: rpm = (10000 * 1 * 20480 * 60) ÷ (2500 * 2048 * 4) = 600 rpm Now, consider that the motor is sped up to 3000 rpm. This results in 409,600 pulses per second, or 102,400 every ¼ of a second. Again, the above equation gives: November 08, 2011 1337 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) rpm = (10000 * 1 * 102400 * 60) ÷ (2500 * 2048 * 4) = 3000 rpm Care must be taken when evaluating this equation because intermediate values may exceed the capacity of a 32-bit integer. In the above examples, the clock is 10,000 and the divider is 2,500; both could be predivided by 100 (at compile time if they are constants) and therefore be 100 and 25. In fact, if they were compile-time constants, they could also be reduced to a simple multiply by 4, cancelled by the ÷4 for the edge-count factor. Important: Reducing constant factors at compile time is the best way to control the intermediate values of this equation and reduce the processing requirement of computing this equation. The division can be avoided by selecting a timer load value such that the divisor is a power of 2; a simple shift can therefore be done in place of the division. For encoders with a power of 2 pulses per revolution, the load value can be a power of 2. For other encoders, a load value must be selected such that the product is very close to a power of 2. For example, a 100 pulse-per-revolution encoder could use a load value of 82, resulting in 32,800 as the divisor, which is 0.09% above 214. In this case a shift by 15 would be an adequate approximation of the divide in most cases. If absolute accuracy were required, the microcontroller’s divide instruction could be used. The QEI module can produce a controller interrupt on several events: phase error, direction change, reception of the index pulse, and expiration of the velocity timer. Standard masking, raw interrupt status, interrupt status, and interrupt clear capabilities are provided. 21.4 Initialization and Configuration The following example shows how to configure the Quadrature Encoder module to read back an absolute position: 1. Enable the QEI clock using the RCGCQEI register in the System Control module (see page 405). 2. Enable the clock to the appropriate GPIO module via the RCGCGPIO register in the System Control module (see page 389). 3. In the GPIO module, enable the appropriate pins for their alternate function using the GPIOAFSEL register. To determine which GPIOs to configure, see Table 23-4 on page 1387. 4. Configure the PMCn fields in the GPIOPCTL register to assign the QEI signals to the appropriate pins (see page 717 and Table 23-5 on page 1398). 5. Configure the quadrature encoder to capture edges on both signals and maintain an absolute position by resetting on index pulses. A 1000-line encoder with four edges per line, results in 4000 pulses per revolution; therefore, set the maximum position to 3999 (0xF9F) as the count is zero-based. ■ Write the QEICTL register with the value of 0x0000.0018. ■ Write the QEIMAXPOS register with the value of 0x0000.0F9F. 6. Enable the quadrature encoder by setting bit 0 of the QEICTL register. 7. Delay until the encoder position is required. 8. Read the encoder position by reading the QEI Position (QEIPOS) register value. 1338 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 21.5 Register Map Table 21-2 on page 1339 lists the QEI registers. The offset listed is a hexadecimal increment to the register’s address, relative to the module’s base address: ■ QEI0: 0x4002.C000 ■ QEI1: 0x4002.D000 Note that the QEI module clock must be enabled before the registers can be programmed (see page 405). There must be a delay of 3 system clocks after the QEI module clock is enabled before any QEI module registers are accessed. Table 21-2. QEI Register Map Offset Name Type Reset Description See page 0x000 QEICTL R/W 0x0000.0000 QEI Control 1340 0x004 QEISTAT RO 0x0000.0000 QEI Status 1343 0x008 QEIPOS R/W 0x0000.0000 QEI Position 1344 0x00C QEIMAXPOS R/W 0x0000.0000 QEI Maximum Position 1345 0x010 QEILOAD R/W 0x0000.0000 QEI Timer Load 1346 0x014 QEITIME RO 0x0000.0000 QEI Timer 1347 0x018 QEICOUNT RO 0x0000.0000 QEI Velocity Counter 1348 0x01C QEISPEED RO 0x0000.0000 QEI Velocity 1349 0x020 QEIINTEN R/W 0x0000.0000 QEI Interrupt Enable 1350 0x024 QEIRIS RO 0x0000.0000 QEI Raw Interrupt Status 1352 0x028 QEIISC R/W1C 0x0000.0000 QEI Interrupt Status and Clear 1354 21.6 Register Descriptions The remainder of this section lists and describes the QEI registers, in numerical order by address offset. November 08, 2011 1339 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Register 1: QEI Control (QEICTL), offset 0x000 This register contains the configuration of the QEI module. Separate enables are provided for the quadrature encoder and the velocity capture blocks; the quadrature encoder must be enabled in order to capture the velocity, but the velocity does not need to be captured in applications that do not need it. The phase signal interpretation, phase swap, Position Update mode, Position Reset mode, and velocity predivider are all set via this register. QEI Control (QEICTL) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 FILTEN STALLEN R/W 0 R/W 0 25 24 23 22 21 20 19 18 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 10 9 8 7 6 5 4 3 2 1 0 INVI INVB INVA SWAP ENABLE R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 RO 0 17 16 FILTCNT VELDIV R/W 0 R/W 0 VELEN RESMODE CAPMODE SIGMODE R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:20 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 19:16 FILTCNT R/W 0x0 Input Filter Prescale Count This field controls the frequency of the input update. When this field is clear, the input is sampled after 2 system clocks. When this field ix 0x1, the input is sampled after 3 system clocks. Similarly, when this field is 0xF, the input is sampled after 17 clocks. 15:14 reserved RO 0x0 13 FILTEN R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Enable Input Filter Value Description 12 STALLEN R/W 0 0 The QEI inputs are not filtered. 1 Enables the digital noise filter on the QEI input signals. Inputs must be stable for 3 consecutive clock edges before the edge detector is updated. Stall QEI Value Description 0 The QEI module does not stall when the microcontroller is stopped by a debugger. 1 The QEI module stalls when the microcontroller is stopped by a debugger. 1340 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 11 INVI R/W 0 Description Invert Index Pulse Value Description 10 INVB R/W 0 0 No effect. 1 Inverts the IDX input. Invert PhB Value Description 9 INVA R/W 0 0 No effect. 1 Inverts the PhB input. Invert PhA Value Description 8:6 VELDIV R/W 0x0 0 No effect. 1 Inverts the PhA input. Predivide Velocity This field defines the predivider of the input quadrature pulses before being applied to the QEICOUNT accumulator. Value Predivider 5 VELEN R/W 0 0x0 ÷1 0x1 ÷2 0x2 ÷4 0x3 ÷8 0x4 ÷16 0x5 ÷32 0x6 ÷64 0x7 ÷128 Capture Velocity Value Description 4 RESMODE R/W 0 0 No effect. 1 Enables capture of the velocity of the quadrature encoder. Reset Mode Value Description 0 The position counter is reset when it reaches the maximum as defined by the MAXPOS field in the QEIMAXPOS register. 1 The position counter is reset when the index pulse is captured. November 08, 2011 1341 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Bit/Field Name Type Reset 3 CAPMODE R/W 0 Description Capture Mode Value Description 2 SIGMODE R/W 0 0 Only the PhA edges are counted. 1 The PhA and PhB edges are counted, providing twice the positional resolution but half the range. Signal Mode Value Description 1 SWAP R/W 0 0 The PhA and PhB signals operate as quadrature phase signals. 1 The PhA and PhB signals operate as clock and direction. Swap Signals Value Description 0 ENABLE R/W 0 0 No effect. 1 Swaps the PhA and PhB signals. Enable QEI Value Description 0 No effect. 1 Enables the quadrature encoder module. 1342 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 2: QEI Status (QEISTAT), offset 0x004 This register provides status about the operation of the QEI module. QEI Status (QEISTAT) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x004 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 DIRECTION ERROR RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1 DIRECTION RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Direction of Rotation Indicates the direction the encoder is rotating. Value Description 0 ERROR RO 0 0 The encoder is rotating forward. 1 The encoder is rotating in reverse. Error Detected Value Description 0 No error. 1 An error was detected in the gray code sequence (that is, both signals changing at the same time). November 08, 2011 1343 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Register 3: QEI Position (QEIPOS), offset 0x008 This register contains the current value of the position integrator. The value is updated by the status of the QEI phase inputs and can be set to a specific value by writing to it. QEI Position (QEIPOS) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 POSITION Type Reset POSITION Type Reset Bit/Field Name Type 31:0 POSITION R/W Reset R/W 0 Description 0x0000.0000 Current Position Integrator Value The current value of the position integrator. 1344 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 4: QEI Maximum Position (QEIMAXPOS), offset 0x00C This register contains the maximum value of the position integrator. When moving forward, the position register resets to zero when it increments past this value. When moving in reverse, the position register resets to this value when it decrements from zero. QEI Maximum Position (QEIMAXPOS) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x00C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 MAXPOS Type Reset MAXPOS Type Reset Bit/Field Name Type 31:0 MAXPOS R/W Reset Description 0x0000.0000 Maximum Position Integrator Value The maximum value of the position integrator. November 08, 2011 1345 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Register 5: QEI Timer Load (QEILOAD), offset 0x010 This register contains the load value for the velocity timer. Because this value is loaded into the timer on the clock cycle after the timer is zero, this value should be one less than the number of clocks in the desired period. So, for example, to have 2000 decimal clocks per timer period, this register should contain 1999 decimal. QEI Timer Load (QEILOAD) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 LOAD Type Reset LOAD Type Reset Bit/Field Name Type 31:0 LOAD R/W Reset Description 0x0000.0000 Velocity Timer Load Value The load value for the velocity timer. 1346 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 6: QEI Timer (QEITIME), offset 0x014 This register contains the current value of the velocity timer. This counter does not increment when the VELEN bit in the QEICTL register is clear. QEI Timer (QEITIME) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x014 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 TIME Type Reset TIME Type Reset Bit/Field Name Type 31:0 TIME RO Reset Description 0x0000.0000 Velocity Timer Current Value The current value of the velocity timer. November 08, 2011 1347 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Register 7: QEI Velocity Counter (QEICOUNT), offset 0x018 This register contains the running count of velocity pulses for the current time period. Because this count is a running total, the time period to which it applies cannot be known with precision (that is, a read of this register does not necessarily correspond to the time returned by the QEITIME register because there is a small window of time between the two reads, during which either value may have changed). The QEISPEED register should be used to determine the actual encoder velocity; this register is provided for information purposes only. This counter does not increment when the VELEN bit in the QEICTL register is clear. QEI Velocity Counter (QEICOUNT) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x018 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 COUNT Type Reset COUNT Type Reset Bit/Field Name Type 31:0 COUNT RO Reset Description 0x0000.0000 Velocity Pulse Count The running total of encoder pulses during this velocity timer period. 1348 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Register 8: QEI Velocity (QEISPEED), offset 0x01C This register contains the most recently measured velocity of the quadrature encoder. This value corresponds to the number of velocity pulses counted in the previous velocity timer period. This register does not update when the VELEN bit in the QEICTL register is clear. QEI Velocity (QEISPEED) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x01C Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 SPEED Type Reset SPEED Type Reset Bit/Field Name Type 31:0 SPEED RO Reset Description 0x0000.0000 Velocity The measured speed of the quadrature encoder in pulses per period. November 08, 2011 1349 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Register 9: QEI Interrupt Enable (QEIINTEN), offset 0x020 This register contains enables for each of the QEI module interrupts. An interrupt is asserted to the interrupt controller if the corresponding bit in this register is set. QEI Interrupt Enable (QEIINTEN) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x020 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 INTERROR INTDIR INTTIMER INTINDEX RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 INTERROR R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Phase Error Interrupt Enable Value Description 2 INTDIR R/W 0 1 An interrupt is sent to the interrupt controller when the INTERROR bit in the QEIRIS register is set. 0 The INTERROR interrupt is suppressed and not sent to the interrupt controller. Direction Change Interrupt Enable Value Description 1 INTTIMER R/W 0 1 An interrupt is sent to the interrupt controller when the INTDIR bit in the QEIRIS register is set. 0 The INTDIR interrupt is suppressed and not sent to the interrupt controller. Timer Expires Interrupt Enable Value Description 1 An interrupt is sent to the interrupt controller when the INTTIMER bit in the QEIRIS register is set. 0 The INTTIMER interrupt is suppressed and not sent to the interrupt controller. 1350 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 0 INTINDEX R/W 0 Description Index Pulse Detected Interrupt Enable Value Description 1 An interrupt is sent to the interrupt controller when the INTINDEX bit in the QEIRIS register is set. 0 The INTINDEX interrupt is suppressed and not sent to the interrupt controller. November 08, 2011 1351 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Register 10: QEI Raw Interrupt Status (QEIRIS), offset 0x024 This register provides the current set of interrupt sources that are asserted, regardless of whether they cause an interrupt to be asserted to the controller (configured through the QEIINTEN register). If a bit is set, the latched event has occurred; if a bit is clear, the event in question has not occurred. QEI Raw Interrupt Status (QEIRIS) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x024 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 INTERROR INTDIR INTTIMER INTINDEX RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 INTERROR RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Phase Error Detected Value Description 1 A phase error has been detected. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTERROR bit in the QEIISC register. 2 INTDIR RO 0 Direction Change Detected Value Description 1 The rotation direction has changed 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTDIR bit in the QEIISC register. 1 INTTIMER RO 0 Velocity Timer Expired Value Description 1 The velocity timer has expired. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTTIMER bit in the QEIISC register. 1352 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 0 INTINDEX RO 0 Description Index Pulse Asserted Value Description 1 The index pulse has occurred. 0 An interrupt has not occurred. This bit is cleared by writing a 1 to the INTINDEX bit in the QEIISC register. November 08, 2011 1353 Texas Instruments-Advance Information Quadrature Encoder Interface (QEI) Register 11: QEI Interrupt Status and Clear (QEIISC), offset 0x028 This register provides the current set of interrupt sources that are asserted to the controller. If a bit is set, the latched event has occurred and is enabled to generate an interrupt; if a bit is clear the event in question has not occurred or is not enabled to generate an interrupt. This register is R/W1C; writing a 1 to a bit position clears the bit and the corresponding interrupt reason. QEI Interrupt Status and Clear (QEIISC) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 Offset 0x028 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 INTERROR INTDIR INTTIMER INTINDEX RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:4 reserved RO 0x0000.000 3 INTERROR R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Phase Error Interrupt Value Description 1 The INTERROR bits in the QEIRIS register and the QEIINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTERROR bit in the QEIRIS register. 2 INTDIR R/W1C 0 Direction Change Interrupt Value Description 1 The INTDIR bits in the QEIRIS register and the QEIINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTDIR bit in the QEIRIS register. 1 INTTIMER R/W1C 0 Velocity Timer Expired Interrupt Value Description 1 The INTTIMER bits in the QEIRIS register and the QEIINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTTIMER bit in the QEIRIS register. 1354 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Bit/Field Name Type Reset 0 INTINDEX R/W1C 0 Description Index Pulse Interrupt Value Description 1 The INTINDEX bits in the QEIRIS register and the QEIINTEN registers are set, providing an interrupt to the interrupt controller. 0 No interrupt has occurred or the interrupt is masked. This bit is cleared by writing a 1. Clearing this bit also clears the INTINDEX bit in the QEIRIS register. November 08, 2011 1355 Texas Instruments-Advance Information Pin Diagram 22 Pin Diagram The LM4F232H5BB microcontroller pin diagram is shown below. Each GPIO signal is identified by its GPIO port unless it defaults to an alternate function on reset. In this case, the GPIO port name is followed by the default alternate function. To see a complete list of possible functions for each pin, see Table 23-5 on page 1398. Figure 22-1. 157-Ball BGA Package Pin Diagram (Top View) 1356 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 23 Signal Tables The following tables list the signals available for each pin. Signals are configured as GPIOs on reset, except for those noted below. Use the GPIOAMSEL register (see page 715) to select analog mode. For a GPIO pin to be used for an alternate digital function, the corresponding bit in the GPIOAFSEL register (see page 698) must be set. Further pin muxing options are provided through the PMCx bit field in the GPIOPCTL register (see page 717), which selects one of several available peripheral functions for that GPIO. Important: All GPIO pins are configured as GPIOs by default with the exception of the pins shown in the table below. A Power-On-Reset (POR) or asserting RST puts the pins back to their default state. Table 23-1. GPIO Pins With Default Alternate Functions GPIO Pin Default State GPIOAFSEL Bit GPIOPCTL PMCx Bit Field PA[1:0] UART0 0 0x1 PA[5:2] SSI0 0 0x1 PB[3:2] I2C0 0 0x1 PC[3:0] JTAG/SWD 1 0x3 Table 23-2 on page 1358 shows the pin-to-signal-name mapping, including functional characteristics of the signals. Each possible alternate analog and digital function is listed for each pin. Table 23-3 on page 1374 lists the signals in alphabetical order by signal name. If it is possible for a signal to be on multiple pins, each possible pin assignment is listed. The "Pin Mux" column indicates the GPIO and the encoding needed in the PMCx bit field in the GPIOPCTL register. Table 23-4 on page 1387 groups the signals by functionality, except for GPIOs. If it is possible for a signal to be on multiple pins, each possible pin assignment is listed. Table 23-5 on page 1398 lists the GPIO pins and their analog and digital alternate functions. The AINx analog signals are not 5-V tolerant and go through an isolation circuit before reaching their circuitry. These signals are configured by clearing the corresponding DEN bit in the GPIO Digital Enable (GPIODEN) register and setting the corresponding AMSEL bit in the GPIO Analog Mode Select (GPIOAMSEL) register. Other analog signals are 5-V tolerant and are connected directly to their circuitry (C0-, C0+, C1-, C1+, C2-, C2+, USB0VBUS, USB0ID). These signals are configured by clearing the DEN bit in the GPIO Digital Enable (GPIODEN) register. The digital signals are enabled by setting the appropriate bit in the GPIO Alternate Function Select (GPIOAFSEL) and GPIODEN registers and configuring the PMCx bit field in the GPIO Port Control (GPIOPCTL) register to the numeric enoding shown in the table below. Table entries that are shaded gray are the default values for the corresponding GPIO pin. Table 23-6 on page 1402 lists the signals based on number of possible pin assignments. This table can be used to plan how to configure the pins for a particular functionality. Application Note AN01274 ® Configuring Stellaris Microcontrollers with Pin Multiplexing provides an overview of the pin muxing implementation, an explanation of how a system designer defines a pin configuration, and examples of the pin configuration process. Note: All digital inputs are Schmitt triggered. November 08, 2011 1357 Texas Instruments-Advance Information Signal Tables Table 23-2. Signals by Pin Number a Pin Number Pin Name Pin Type Buffer Type A1 GND - Power A2 NC - - PD6 I/O TTL GPIO port D bit 6. I Analog I TTL Motion Control Module 0 PWM Fault 0. PhA0 I TTL QEI module 0 phase A. U2Rx I TTL UART module 2 receive. WT5CCP0 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 0. PD4 I/O TTL GPIO port D bit 4. AIN7 I Analog Analog-to-digital converter input 5. Analog-to-digital converter input 7. U6Rx I TTL UART module 6 receive. WT4CCP0 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 0. PE4 I/O TTL GPIO port E bit 4. AIN9 I Analog CAN0Rx I TTL CAN module 0 receive. I2C2SCL I/O OD I2C module 2 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. M0PWM4 O TTL Motion Control Module 0 PWM 4. This signal is controlled by Module 0 PWM Generator 2. M1PWM2 O TTL Motion Control Module 1 PWM 2. This signal is controlled by Module 1 PWM Generator 1. U5Rx I TTL UART module 5 receive. GPIO port B bit 5. A5 A8 No connect. Leave the pin electrically unconnected/isolated. AIN5 A4 A7 Ground reference for logic and I/O pins. M0FAULT0 A3 A6 Description Analog-to-digital converter input 9. PB5 I/O TTL AIN11 I Analog CAN0Tx O TTL CAN module 0 transmit. M0PWM3 O TTL Motion Control Module 0 PWM 3. This signal is controlled by Module 0 PWM Generator 1. SSI2Fss I/O TTL SSI module 2 frame. T1CCP1 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 1. GPIO port E bit 6. Analog-to-digital converter input 11. PE6 I/O TTL AIN21 I Analog CAN1Rx I TTL CAN module 1 receive. GPIO port N bit 0. Analog-to-digital converter input 21. PN0 I/O TTL AIN23 I Analog CAN0Rx I TTL CAN module 0 receive. Analog-to-digital converter input 23. PJ2 I/O TTL GPIO port J bit 2. IDX0 I TTL QEI module 0 index. T2CCP0 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 0. U5Rx I TTL UART module 5 receive. A9 1358 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-2. Signals by Pin Number (continued) Pin Number Pin Type Buffer Type Description PC1 I/O TTL GPIO port C bit 1. SWDIO I/O TTL JTAG TMS and SWDIO. T4CCP1 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 1. TMS I TTL JTAG TMS and SWDIO. PC3 I/O TTL GPIO port C bit 3. A10 SWO O TTL JTAG TDO and SWO. T5CCP1 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 1. TDO O TTL JTAG TDO and SWO. A11 A12 a Pin Name PK7 I/O TTL GPIO port K bit 7. M0FAULT3 I TTL Motion Control Module 0 PWM Fault 3. WT1CCP1 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 1. PL2 I/O TTL GPIO port L bit 2. T1CCP0 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 0. WT1CCP0 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 0. PD1 I/O TTL GPIO port D bit 1. A13 AIN14 I Analog I2C3SDA I/O OD I2C module 3 data. M0PWM7 O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. M1PWM1 O TTL Motion Control Module 1 PWM 1. This signal is controlled by Module 1 PWM Generator 0. SSI1Fss I/O TTL SSI module 1 frame. SSI3Fss I/O TTL SSI module 3 frame. WT2CCP1 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 1. PD0 I/O TTL GPIO port D bit 0. B1 Analog-to-digital converter input 14. AIN15 I Analog I2C3SCL I/O OD I2C module 3 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. M0PWM6 O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. M1PWM0 O TTL Motion Control Module 1 PWM 0. This signal is controlled by Module 1 PWM Generator 0. SSI1Clk I/O TTL SSI module 1 clock. SSI3Clk I/O TTL SSI module 3 clock. WT2CCP0 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 0. PD7 I/O TTL GPIO port D bit 7. AIN4 I Analog M0FAULT1 I TTL Motion Control Module 0 PWM Fault 1. NMI I TTL Non-maskable interrupt. PhB0 I TTL QEI module 0 phase B. U2Tx O TTL UART module 2 transmit. WT5CCP1 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 1. B2 B3 Analog-to-digital converter input 15. Analog-to-digital converter input 4. November 08, 2011 1359 Texas Instruments-Advance Information Signal Tables Table 23-2. Signals by Pin Number (continued) Pin Number Pin Name Pin Type B6 PD5 I/O TTL I Analog U6Tx O TTL UART module 6 transmit. WT4CCP1 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 1. PE5 I/O TTL GPIO port E bit 5. B9 B10 B11 GPIO port D bit 5. Analog-to-digital converter input 6. AIN8 I Analog CAN0Tx O TTL CAN module 0 transmit. I2C2SDA I/O OD I2C module 2 data. M0PWM5 O TTL Motion Control Module 0 PWM 5. This signal is controlled by Module 0 PWM Generator 2. M1PWM3 O TTL Motion Control Module 1 PWM 3. This signal is controlled by Module 1 PWM Generator 1. U5Tx O TTL UART module 5 transmit. PB4 I/O TTL GPIO port B bit 4. AIN10 I Analog CAN0Rx I TTL CAN module 0 receive. M0PWM2 O TTL Motion Control Module 0 PWM 2. This signal is controlled by Module 0 PWM Generator 1. SSI2Clk I/O TTL SSI module 2 clock. T1CCP0 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 0. Analog-to-digital converter input 8. GPIO port E bit 7. Analog-to-digital converter input 10. PE7 I/O TTL AIN20 I Analog CAN1Tx O TTL CAN module 1 transmit. U1RI I TTL UART module 1 Ring Indicator modem status input signal. PN1 I/O TTL GPIO port N bit 1. B7 B8 Description AIN6 B4 B5 a Buffer Type Analog-to-digital converter input 20. AIN22 I Analog CAN0Tx O TTL Analog-to-digital converter input 22. CAN module 0 transmit. PJ1 I/O TTL GPIO port J bit 1. T1CCP1 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 1. U4Tx O TTL UART module 4 transmit. PC2 I/O TTL GPIO port C bit 2. T5CCP0 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 0. TDI I TTL JTAG TDI. PK4 I/O TTL GPIO port K bit 4. C0o O TTL Analog comparator 0 output. M0FAULT0 I TTL Motion Control Module 0 PWM Fault 0. RTCCLK O TTL Buffered version of the Hibernation module's 32.768-kHz clock. This signal is not output when the part is in Hibernation mode. U7Rx I TTL UART module 7 receive. 1360 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-2. Signals by Pin Number (continued) Pin Number a Pin Name Pin Type Buffer Type PK5 I/O TTL GPIO port K bit 5. C1o O TTL Analog comparator 1 output. M0FAULT1 I TTL Motion Control Module 0 PWM Fault 1. U7Tx O TTL UART module 7 transmit. PL3 I/O TTL GPIO port L bit 3. B12 Description T1CCP1 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 1. WT1CCP1 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 1. PD3 I/O TTL GPIO port D bit 3. AIN12 I Analog IDX0 I TTL QEI module 0 index. SSI1Tx O TTL SSI module 1 transmit. SSI3Tx O TTL SSI module 3 transmit. USB0PFLT I TTL Optionally used in Host mode by an external power source to indicate an error state by that power source. WT3CCP1 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 1. GPIO port D bit 2. B13 C1 Analog-to-digital converter input 12. PD2 I/O TTL AIN13 I Analog M0FAULT0 I TTL Motion Control Module 0 PWM Fault 0. SSI1Rx I TTL SSI module 1 receive. SSI3Rx I TTL SSI module 3 receive. USB0EPEN O TTL Optionally used in Host mode to control an external power source to supply power to the USB bus. WT3CCP0 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 0. GNDA - Power PJ7 I/O TTL GPIO port J bit 7. PJ5 I/O TTL GPIO port J bit 5. C2 C3 C4 Analog-to-digital converter input 13. The ground reference for the analog circuits (ADC, Analog Comparators, etc.). These are separated from GND to minimize the electrical noise contained on VDD from affecting the analog functions. C2- I Analog T3CCP1 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 1. U6Tx O TTL UART module 6 transmit. C6 PJ6 I/O TTL GPIO port J bit 6. C7 GND - Power PJ3 I/O TTL GPIO port J bit 3. C8 T2CCP1 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 1. U5Tx O TTL UART module 5 transmit. C5 C9 Analog comparator 2 negative input. Ground reference for logic and I/O pins. PJ0 I/O TTL GPIO port J bit 0. T1CCP0 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 0. U4Rx I TTL UART module 4 receive. November 08, 2011 1361 Texas Instruments-Advance Information Signal Tables Table 23-2. Signals by Pin Number (continued) Pin Number Pin Type Buffer Type PC0 I/O TTL GPIO port C bit 0. I TTL JTAG/SWD CLK. T4CCP0 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 0. TCK I TTL JTAG/SWD CLK. PK6 I/O TTL GPIO port K bit 6. C2o O TTL Analog comparator 2 output. M0FAULT2 I TTL Motion Control Module 0 PWM Fault 2. WT1CCP0 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 0. C11 PL1 I/O TTL GPIO port L bit 1. T0CCP1 I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 1. WT0CCP1 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 1. PL5 I/O TTL GPIO port L bit 5. LPC0RESET I TTL LPC Bus reset signal. C13 T2CCP1 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 1. WT2CCP1 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 1. VREFA- - Analog A reference voltage used to specify the input voltage at which the ADC converts to a minimum value. This pin is used in conjunction with VREFA+ which specifies the maximum value. In other words, the voltage that is applied to VREFA- is the voltage with which an AINn signal is converted to 0, while the voltage that is applied to VREFA+ is the voltage with which an AINn signal is converted to 4095. The VREFA- voltage is limited to the range specified in Table 25-24 on page 1422. VREFA+ - Analog A reference voltage used to specify the voltage at which the ADC converts to a maximum value. This pin is used in conjunction with VREFA- which specifies the minimum value. In other words, the voltage that is applied to VREFA+ is the voltage with which an AINn signal is converted to 4095. The VREFA+ voltage is limited to the range specified in Table 25-24 on page 1422. VDDA - Power The positive supply (3.3 V) for the analog circuits (ADC, Analog Comparators, etc.). These are separated from VDD to minimize the electrical noise contained on VDD from affecting the analog functions. VDDA pins must be connected to 3.3 V, regardless of system implementation. PQ0 I/O TTL GPIO port Q bit 0. M1PWM0 O TTL Motion Control Module 1 PWM 0. This signal is controlled by Module 1 PWM Generator 0. WT2CCP0 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 0. PJ4 I/O TTL GPIO port J bit 4. D1 D2 D3 D4 C2+ I Analog T3CCP0 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 0. U6Rx I TTL UART module 6 receive. VDDC - Power Positive supply for most of the logic function, including the processor core and most peripherals. VDD - Power Positive supply for I/O and some logic. D5 D6 D7 Description SWCLK C10 C12 a Pin Name Analog comparator 2 positive input. 1362 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-2. Signals by Pin Number (continued) Pin Number a Pin Name Pin Type Buffer Type D8 D9 D10 D11 Description PP6 I/O TTL GPIO port P bit 6. M0PWM6 O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. WT1CCP0 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 0. GND - Power Ground reference for logic and I/O pins. PN3 I/O TTL GPIO port N bit 3. M0PWM7 O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. WT2CCP1 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 1. PL0 I/O TTL GPIO port L bit 0. T0CCP0 I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 0. WT0CCP0 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 0. PL4 I/O TTL GPIO port L bit 4. LPC0FRAME I TTL This input signals the start or abort of a transaction. T2CCP0 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 0. WT2CCP0 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 0. PB3 I/O TTL GPIO port B bit 3. I2C0SDA I/O OD I2C module 0 data. T3CCP1 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 1. PE2 I/O TTL GPIO port E bit 2. AIN1 I Analog PE3 I/O TTL AIN0 I Analog Analog-to-digital converter input 0. GNDA - Power The ground reference for the analog circuits (ADC, Analog Comparators, etc.). These are separated from GND to minimize the electrical noise contained on VDD from affecting the analog functions. D12 D13 E1 E2 E3 Analog-to-digital converter input 1. GPIO port E bit 3. PQ1 I/O TTL GPIO port Q bit 1. M1PWM1 O TTL Motion Control Module 1 PWM 1. This signal is controlled by Module 1 PWM Generator 0. WT2CCP1 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 1. E5 GND - Power Ground reference for logic and I/O pins. E6 VDD - Power Positive supply for I/O and some logic. E8 VDD - Power Positive supply for I/O and some logic. E9 VDD - Power Positive supply for I/O and some logic. PB2 I/O TTL GPIO port B bit 2. I2C0SCL I/O OD I2C module 0 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. T3CCP0 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 0. E4 E10 November 08, 2011 1363 Texas Instruments-Advance Information Signal Tables Table 23-2. Signals by Pin Number (continued) Pin Number E11 E12 E13 F1 F2 a Pin Name Pin Type Buffer Type Description PB1 I/O TTL GPIO port B bit 1. This pin is not 5-V tolerant. T2CCP1 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 1. U1Tx O TTL UART module 1 transmit. USB0VBUS I/O Analog PL6 I/O TTL GPIO port L bit 6. T3CCP0 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 0. USB0DP I/O Analog WT3CCP0 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 0. PL7 I/O TTL GPIO port L bit 7. T3CCP1 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 1. USB0DM I/O Analog WT3CCP1 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 1. PE0 I/O TTL GPIO port E bit 0. AIN3 I Analog U7Rx I TTL UART module 7 receive. GPIO port E bit 1. This signal is used during the session request protocol. This signal allows the USB PHY to both sense the voltage level of VBUS, and pull up VBUS momentarily during VBUS pulsing. Bidirectional differential data pin (D+ per USB specification) for USB0. Bidirectional differential data pin (D- per USB specification) for USB0. Analog-to-digital converter input 3. PE1 I/O TTL AIN2 I Analog U7Tx O TTL UART module 7 transmit. Analog-to-digital converter input 2. PB7 I/O TTL GPIO port B bit 7. I2C5SDA I/O OD I2C module 5 data. M0PWM1 O TTL Motion Control Module 0 PWM 1. This signal is controlled by Module 0 PWM Generator 0. SSI2Tx O TTL SSI module 2 transmit. T0CCP1 I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 1. PB6 I/O TTL GPIO port B bit 6. I2C5SCL I/O OD I2C module 5 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. M0PWM0 O TTL Motion Control Module 0 PWM 0. This signal is controlled by Module 0 PWM Generator 0. SSI2Rx I TTL SSI module 2 receive. T0CCP0 I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 0. PQ2 I/O TTL GPIO port Q bit 2. M1PWM2 O TTL Motion Control Module 1 PWM 2. This signal is controlled by Module 1 PWM Generator 1. WT3CCP0 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 0. F9 GND - Power Ground reference for logic and I/O pins. F10 VDD - Power Positive supply for I/O and some logic. F3 F4 F5 1364 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-2. Signals by Pin Number (continued) Pin Number a Pin Name Pin Type Buffer Type F11 Description PB0 I/O TTL GPIO port B bit 0. This pin is not 5-V tolerant. T2CCP0 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 0. U1Rx I TTL UART module 1 receive. USB0ID I Analog This signal senses the state of the USB ID signal. The USB PHY enables an integrated pull-up, and an external element (USB connector) indicates the initial state of the USB controller (pulled down is the A side of the cable and pulled up is the B side). PM1 I/O TTL GPIO port M bit 1. LPC0SCI O TTL Optional SCI interrupt for ACPI or other uses. F12 T4CCP1 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 1. WT4CCP1 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 1. PM0 I/O TTL GPIO port M bit 0. LPC0PD I TTL Power down and sleep signal from host. T4CCP0 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 0. WT4CCP0 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 0. PK1 I/O TTL GPIO port K bit 1. AIN17 I Analog M1FAULT1 I TTL Motion Control Module 1 PWM Fault 1. SSI3Fss I/O TTL SSI module 3 frame. PK0 I/O TTL GPIO port K bit 0. F13 G1 Analog-to-digital converter input 17. AIN16 I Analog M1FAULT0 I TTL Motion Control Module 1 PWM Fault 0. SSI3Clk I/O TTL SSI module 3 clock. PN2 I/O TTL GPIO port N bit 2. M0PWM6 O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. WT2CCP0 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 0. G2 G3 Analog-to-digital converter input 16. PH7 I/O TTL GPIO port H bit 7. M0PWM7 O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. SSI2Tx O TTL SSI module 2 transmit. WT4CCP1 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 1. G4 RST I TTL System reset input. PM2 I/O TTL GPIO port M bit 2. LPC0CLKRUN O TTL Application may optionally connect this pin to drive CLKRUN to wake a sleeping bus when wanted (or to prevent it from sleeping). G10 G11 G12 G13 T5CCP0 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 0. WT5CCP0 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 0. OSC0 I Analog Main oscillator crystal input or an external clock reference input. OSC1 O Analog Main oscillator crystal output. Leave unconnected when using a single-ended clock source. November 08, 2011 1365 Texas Instruments-Advance Information Signal Tables Table 23-2. Signals by Pin Number (continued) Pin Number Pin Name Pin Type a Buffer Type Description PK2 I/O TTL AIN18 I Analog M1FAULT2 I TTL Motion Control Module 1 PWM Fault 2. SSI3Rx I TTL SSI module 3 receive. PK3 I/O TTL GPIO port K bit 3. H1 GPIO port K bit 2. Analog-to-digital converter input 18. AIN19 I Analog M1FAULT3 I TTL Motion Control Module 1 PWM Fault 3. SSI3Tx O TTL SSI module 3 transmit. H2 Analog-to-digital converter input 19. PH6 I/O TTL GPIO port H bit 6. M0PWM6 O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. SSI2Rx I TTL SSI module 2 receive. WT4CCP0 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 0. H3 PH5 I/O TTL GPIO port H bit 5. M0PWM5 O TTL Motion Control Module 0 PWM 5. This signal is controlled by Module 0 PWM Generator 2. PhB0 I TTL QEI module 0 phase B. SSI2Fss I/O TTL SSI module 2 frame. WT3CCP1 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 1. H5 GND - Power Ground reference for logic and I/O pins. H9 GND - Power Ground reference for logic and I/O pins. PM3 I/O TTL GPIO port M bit 3. H4 H10 H11 T5CCP1 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 1. WT5CCP1 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 1. PM6 I/O TTL GPIO port M bit 6. M0PWM4 O TTL Motion Control Module 0 PWM 4. This signal is controlled by Module 0 PWM Generator 2. WT0CCP0 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 0. H12 PM5 I/O TTL GPIO port M bit 5. H13 PM4 I/O TTL GPIO port M bit 4. VDDC - Power J1 J2 Positive supply for most of the logic function, including the processor core and most peripherals. PH3 I/O TTL GPIO port H bit 3. M0FAULT3 I TTL Motion Control Module 0 PWM Fault 3. M0PWM3 O TTL Motion Control Module 0 PWM 3. This signal is controlled by Module 0 PWM Generator 1. SSI3Tx O TTL SSI module 3 transmit. WT5CCP1 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 1. 1366 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-2. Signals by Pin Number (continued) Pin Number a Pin Name Pin Type Buffer Type Description PH4 I/O TTL GPIO port H bit 4. M0PWM4 O TTL Motion Control Module 0 PWM 4. This signal is controlled by Module 0 PWM Generator 2. PhA0 I TTL QEI module 0 phase A. SSI2Clk I/O TTL SSI module 2 clock. WT3CCP0 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 0. PH2 I/O TTL GPIO port H bit 2. M0FAULT2 I TTL Motion Control Module 0 PWM Fault 2. M0PWM2 O TTL Motion Control Module 0 PWM 2. This signal is controlled by Module 0 PWM Generator 1. J3 J4 SSI3Rx I TTL SSI module 3 receive. WT5CCP0 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 0. GND - Power Ground reference for logic and I/O pins. VDDC - Power Positive supply for most of the logic function, including the processor core and most peripherals. J7 VDD - Power Positive supply for I/O and some logic. J8 GND - Power Ground reference for logic and I/O pins. J5 J6 J9 VDD - Power Positive supply for I/O and some logic. J10 VDD - Power Positive supply for I/O and some logic. J11 GND - Power Ground reference for logic and I/O pins. PP3 I/O TTL GPIO port P bit 3. M0PWM3 O TTL Motion Control Module 0 PWM 3. This signal is controlled by Module 0 PWM Generator 1. T5CCP1 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 1. J12 J13 K1 PP4 I/O TTL GPIO port P bit 4. M0PWM4 O TTL Motion Control Module 0 PWM 4. This signal is controlled by Module 0 PWM Generator 2. WT0CCP0 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 0. PC6 I/O TTL GPIO port C bit 6. C0+ I Analog PhB1 I TTL QEI module 1 phase B. Analog comparator 0 positive input. U3Rx I TTL UART module 3 receive. USB0EPEN O TTL Optionally used in Host mode to control an external power source to supply power to the USB bus. WT1CCP0 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 0. PC7 I/O TTL GPIO port C bit 7. C0- I Analog U3Tx O TTL UART module 3 transmit. USB0PFLT I TTL Optionally used in Host mode by an external power source to indicate an error state by that power source. WT1CCP1 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 1. K2 Analog comparator 0 negative input. November 08, 2011 1367 Texas Instruments-Advance Information Signal Tables Table 23-2. Signals by Pin Number (continued) Pin Number K3 K4 K5 K6 K7 K8 K9 a Pin Name Pin Type Buffer Type Description PH0 I/O TTL GPIO port H bit 0. M0FAULT0 I TTL Motion Control Module 0 PWM Fault 0. M0PWM0 O TTL Motion Control Module 0 PWM 0. This signal is controlled by Module 0 PWM Generator 0. SSI3Clk I/O TTL SSI module 3 clock. WT2CCP0 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 0. PH1 I/O TTL GPIO port H bit 1. IDX0 I TTL QEI module 0 index. M0FAULT1 I TTL Motion Control Module 0 PWM Fault 1. M0PWM1 O TTL Motion Control Module 0 PWM 1. This signal is controlled by Module 0 PWM Generator 0. SSI3Fss I/O TTL SSI module 3 frame. WT2CCP1 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 1. PQ5 I/O TTL GPIO port Q bit 5. M1PWM5 O TTL Motion Control Module 1 PWM 5. This signal is controlled by Module 1 PWM Generator 2. WT4CCP1 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 1. PP7 I/O TTL GPIO port P bit 7. M0PWM7 O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. WT1CCP1 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 1. PG4 I/O TTL GPIO port G bit 4. I2C1SCL I/O OD I2C module 1 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. M0PWM4 O TTL Motion Control Module 0 PWM 4. This signal is controlled by Module 0 PWM Generator 2. M1PWM2 O TTL Motion Control Module 1 PWM 2. This signal is controlled by Module 1 PWM Generator 1. PhB1 I TTL QEI module 1 phase B. U2Rx I TTL UART module 2 receive. USB0EPEN O TTL Optionally used in Host mode to control an external power source to supply power to the USB bus. WT0CCP0 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 0. PG1 I/O TTL GPIO port G bit 1. I2C3SDA I/O OD I2C module 3 data. M1FAULT2 I TTL Motion Control Module 1 PWM Fault 2. PhB1 I TTL QEI module 1 phase B. T4CCP1 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 1. PF5 I/O TTL GPIO port F bit 5. M0FAULT3 I TTL Motion Control Module 0 PWM Fault 3. T2CCP1 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 1. USB0PFLT I TTL Optionally used in Host mode by an external power source to indicate an error state by that power source. 1368 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-2. Signals by Pin Number (continued) Pin Number a Pin Name Pin Type Buffer Type Description PF3 I/O TTL GPIO port F bit 3. CAN0Tx O TTL CAN module 0 transmit. M0FAULT1 I TTL Motion Control Module 0 PWM Fault 1. M1PWM7 O TTL Motion Control Module 1 PWM 7. This signal is controlled by Module 1 PWM Generator 3. SSI1Fss I/O TTL SSI module 1 frame. T1CCP1 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 1. TRCLK O TTL Trace clock. U1DSR I TTL UART module 1 Data Set Ready modem output control line. GNDX - Power GND for the Hibernation oscillator. When using a crystal clock source, this pin should only be connected to the crystal load capacitors to improve oscillator immunity to system noise. When using an external oscillator, this pin should be connected to GND. VBAT - Power Power source for the Hibernation module. It is normally connected to the positive terminal of a battery and serves as the battery backup/Hibernation module power-source supply. VDDC - Power Positive supply for most of the logic function, including the processor core and most peripherals. PC5 I/O TTL C1+ I Analog M0PWM7 O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. PhA1 I TTL QEI module 1 phase A. U1CTS I TTL UART module 1 Clear To Send modem flow control input signal. U1Tx O TTL UART module 1 transmit. U4Tx O TTL UART module 4 transmit. WT0CCP1 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 1. PC4 I/O TTL GPIO port C bit 4. K10 K11 K12 K13 L1 Analog comparator 1 positive input. C1- I Analog IDX1 I TTL QEI module 1 index. M0PWM6 O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. U1RTS O TTL UART module 1 Request to Send modem flow control output line. U1Rx I TTL UART module 1 receive. U4Rx I TTL UART module 4 receive. WT0CCP0 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 0. PA0 I/O TTL GPIO port A bit 0. CAN1Rx I TTL CAN module 1 receive. U0Rx I TTL UART module 0 receive. PA4 I/O TTL GPIO port A bit 4. SSI0Rx I TTL SSI module 0 receive. L2 L3 GPIO port C bit 5. L4 Analog comparator 1 negative input. November 08, 2011 1369 Texas Instruments-Advance Information Signal Tables Table 23-2. Signals by Pin Number (continued) Pin Number L5 L6 L7 L8 L9 a Pin Name Pin Type Buffer Type Description PP5 I/O TTL GPIO port P bit 5. M0PWM5 O TTL Motion Control Module 0 PWM 5. This signal is controlled by Module 0 PWM Generator 2. WT0CCP1 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 1. PQ7 I/O TTL GPIO port Q bit 7. M1PWM7 O TTL Motion Control Module 1 PWM 7. This signal is controlled by Module 1 PWM Generator 3. WT5CCP1 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 1. PG5 I/O TTL GPIO port G bit 5. I2C1SDA I/O OD I2C module 1 data. IDX1 I TTL QEI module 1 index. M0PWM5 O TTL Motion Control Module 0 PWM 5. This signal is controlled by Module 0 PWM Generator 2. M1PWM3 O TTL Motion Control Module 1 PWM 3. This signal is controlled by Module 1 PWM Generator 1. U2Tx O TTL UART module 2 transmit. USB0PFLT I TTL Optionally used in Host mode by an external power source to indicate an error state by that power source. WT0CCP1 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 1. PG0 I/O TTL GPIO port G bit 0. I2C3SCL I/O OD I2C module 3 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. M1FAULT1 I TTL Motion Control Module 1 PWM Fault 1. PhA1 I TTL QEI module 1 phase A. T4CCP0 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 0. PF4 I/O TTL GPIO port F bit 4. IDX0 I TTL QEI module 0 index. M0FAULT2 I TTL Motion Control Module 0 PWM Fault 2. M1FAULT0 I TTL Motion Control Module 1 PWM Fault 0. T2CCP0 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 0. TRD3 O TTL Trace data 3. U1DTR O TTL UART module 1 Data Terminal Ready modem status input signal. USB0EPEN O TTL Optionally used in Host mode to control an external power source to supply power to the USB bus. PF2 I/O TTL GPIO port F bit 2. C2o O TTL Analog comparator 2 output. M0FAULT0 I TTL Motion Control Module 0 PWM Fault 0. M1PWM6 O TTL Motion Control Module 1 PWM 6. This signal is controlled by Module 1 PWM Generator 3. SSI1Clk I/O TTL SSI module 1 clock. T1CCP0 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 0. TRD0 O TTL Trace data 0. U1DCD I TTL UART module 1 Data Carrier Detect modem status input signal. L10 1370 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-2. Signals by Pin Number (continued) Pin Number a Pin Name Pin Type Buffer Type L11 L12 L13 M1 Description PN4 I/O TTL GPIO port N bit 4. M1PWM4 O TTL Motion Control Module 1 PWM 4. This signal is controlled by Module 1 PWM Generator 2. WT3CCP0 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 0. PP1 I/O TTL GPIO port P bit 1. M0PWM1 O TTL Motion Control Module 0 PWM 1. This signal is controlled by Module 0 PWM Generator 0. T4CCP1 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 1. PM7 I/O TTL GPIO port M bit 7. M0PWM5 O TTL Motion Control Module 0 PWM 5. This signal is controlled by Module 0 PWM Generator 2. WT0CCP1 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 1. PA1 I/O TTL GPIO port A bit 1. CAN1Tx O TTL CAN module 1 transmit. U0Tx O TTL UART module 0 transmit. PA2 I/O TTL GPIO port A bit 2. SSI0Clk I/O TTL SSI module 0 clock. M2 PA3 I/O TTL GPIO port A bit 3. SSI0Fss I/O TTL SSI module 0 frame. M3 PA6 I/O TTL GPIO port A bit 6. I2C1SCL I/O OD I2C module 1 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. M1PWM2 O TTL Motion Control Module 1 PWM 2. This signal is controlled by Module 1 PWM Generator 1. M4 PP2 I/O TTL GPIO port P bit 2. M0PWM2 O TTL Motion Control Module 0 PWM 2. This signal is controlled by Module 0 PWM Generator 1. T5CCP0 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 0. PQ6 I/O TTL GPIO port Q bit 6. M1PWM6 O TTL Motion Control Module 1 PWM 6. This signal is controlled by Module 1 PWM Generator 3. WT5CCP0 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 0. PG3 I/O TTL GPIO port G bit 3. I2C4SDA I/O OD I2C module 4 data. M0FAULT2 I TTL Motion Control Module 0 PWM Fault 2. M1PWM1 O TTL Motion Control Module 1 PWM 1. This signal is controlled by Module 1 PWM Generator 0. PhA1 I TTL QEI module 1 phase A. T5CCP1 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 1. PF7 I/O TTL GPIO port F bit 7. I2C2SDA I/O OD I2C module 2 data. M1FAULT0 I TTL Motion Control Module 1 PWM Fault 0. T3CCP1 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 1. M5 M6 M7 M8 November 08, 2011 1371 Texas Instruments-Advance Information Signal Tables Table 23-2. Signals by Pin Number (continued) Pin Number M9 a Pin Name Pin Type Buffer Type PF0 I/O TTL GPIO port F bit 0. C0o O TTL Analog comparator 0 output. CAN0Rx I TTL CAN module 0 receive. M1PWM4 O TTL Motion Control Module 1 PWM 4. This signal is controlled by Module 1 PWM Generator 2. NMI I TTL Non-maskable interrupt. PhA0 I TTL QEI module 0 phase A. SSI1Rx I TTL SSI module 1 receive. T0CCP0 I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 0. TRD2 O TTL Trace data 2. U1RTS O TTL UART module 1 Request to Send modem flow control output line. XOSC0 I Analog Hibernation module oscillator crystal input or an external clock reference input. Note that this is either a 32.768-kHz crystal or a 32.768-kHz oscillator for the Hibernation module RTC. M10 M11 M12 M13 PN7 I/O TTL GPIO port N bit 7. M1PWM7 O TTL Motion Control Module 1 PWM 7. This signal is controlled by Module 1 PWM Generator 3. WT4CCP1 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 1. HIB O TTL An output that indicates the processor is in Hibernate mode. PP0 I/O TTL GPIO port P bit 0. M0PWM0 O TTL Motion Control Module 0 PWM 0. This signal is controlled by Module 0 PWM Generator 0. T4CCP0 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 0. PA5 I/O TTL GPIO port A bit 5. SSI0Tx O TTL SSI module 0 transmit. PA7 I/O TTL GPIO port A bit 7. I2C1SDA I/O OD I2C module 1 data. M1PWM3 O TTL Motion Control Module 1 PWM 3. This signal is controlled by Module 1 PWM Generator 1. N1 N2 N3 Description PG7 I/O TTL GPIO port G bit 7. I2C5SDA I/O OD I2C module 5 data. IDX1 I TTL QEI module 1 index. M0PWM7 O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. WT1CCP1 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 1. PG6 I/O TTL GPIO port G bit 6. I2C5SCL I/O OD I2C module 5 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. M0PWM6 O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. WT1CCP0 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 0. N4 1372 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-2. Signals by Pin Number (continued) Pin Number Pin Type Buffer Type Description PQ3 I/O TTL GPIO port Q bit 3. M1PWM3 O TTL Motion Control Module 1 PWM 3. This signal is controlled by Module 1 PWM Generator 1. WT3CCP1 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 1. PQ4 I/O TTL GPIO port Q bit 4. M1PWM4 O TTL Motion Control Module 1 PWM 4. This signal is controlled by Module 1 PWM Generator 2. WT4CCP0 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 0. PG2 I/O TTL GPIO port G bit 2. I2C4SCL I/O OD I2C module 4 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. M0FAULT1 I TTL Motion Control Module 0 PWM Fault 1. M1PWM0 O TTL Motion Control Module 1 PWM 0. This signal is controlled by Module 1 PWM Generator 0. T5CCP0 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 0. PF6 I/O TTL GPIO port F bit 6. I2C2SCL I/O OD I2C module 2 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. T3CCP0 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 0. PF1 I/O TTL GPIO port F bit 1. C1o O TTL Analog comparator 1 output. M1PWM5 O TTL Motion Control Module 1 PWM 5. This signal is controlled by Module 1 PWM Generator 2. PhB0 I TTL QEI module 0 phase B. SSI1Tx O TTL SSI module 1 transmit. T0CCP1 I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 1. TRD1 O TTL Trace data 1. N5 N6 N7 a Pin Name N8 N9 N10 N11 N12 N13 U1CTS I TTL UART module 1 Clear To Send modem flow control input signal. XOSC1 O Analog Hibernation module oscillator crystal output. Leave unconnected when using a single-ended clock source. PN6 I/O TTL GPIO port N bit 6. M1PWM6 O TTL Motion Control Module 1 PWM 6. This signal is controlled by Module 1 PWM Generator 3. WT4CCP0 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 0. PN5 I/O TTL GPIO port N bit 5. M1PWM5 O TTL Motion Control Module 1 PWM 5. This signal is controlled by Module 1 PWM Generator 2. WT3CCP1 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 1. WAKE I TTL An external input that brings the processor out of Hibernate mode when asserted. a. The TTL designation indicates the pin has TTL-compatible voltage levels. November 08, 2011 1373 Texas Instruments-Advance Information Signal Tables Table 23-3. Signals by Signal Name Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description AIN0 E2 PE3 I Analog Analog-to-digital converter input 0. AIN1 E1 PE2 I Analog Analog-to-digital converter input 1. AIN2 F2 PE1 I Analog Analog-to-digital converter input 2. AIN3 F1 PE0 I Analog Analog-to-digital converter input 3. AIN4 B3 PD7 I Analog Analog-to-digital converter input 4. AIN5 A3 PD6 I Analog Analog-to-digital converter input 5. AIN6 B4 PD5 I Analog Analog-to-digital converter input 6. AIN7 A4 PD4 I Analog Analog-to-digital converter input 7. AIN8 B5 PE5 I Analog Analog-to-digital converter input 8. AIN9 A5 PE4 I Analog Analog-to-digital converter input 9. AIN10 B6 PB4 I Analog Analog-to-digital converter input 10. AIN11 A6 PB5 I Analog Analog-to-digital converter input 11. AIN12 C1 PD3 I Analog Analog-to-digital converter input 12. AIN13 C2 PD2 I Analog Analog-to-digital converter input 13. AIN14 B1 PD1 I Analog Analog-to-digital converter input 14. AIN15 B2 PD0 I Analog Analog-to-digital converter input 15. AIN16 G2 PK0 I Analog Analog-to-digital converter input 16. AIN17 G1 PK1 I Analog Analog-to-digital converter input 17. AIN18 H1 PK2 I Analog Analog-to-digital converter input 18. AIN19 H2 PK3 I Analog Analog-to-digital converter input 19. AIN20 B7 PE7 I Analog Analog-to-digital converter input 20. AIN21 A7 PE6 I Analog Analog-to-digital converter input 21. AIN22 B8 PN1 I Analog Analog-to-digital converter input 22. AIN23 A8 PN0 I Analog Analog-to-digital converter input 23. C0+ K1 PC6 I Analog Analog comparator 0 positive input. C0- K2 PC7 I Analog Analog comparator 0 negative input. C0o M9 B11 PF0 (9) PK4 (8) O TTL C1+ L1 PC5 I Analog Analog comparator 1 positive input. Analog comparator 1 negative input. Analog comparator 0 output. C1- L2 PC4 I Analog C1o N9 B12 PF1 (9) PK5 (8) O TTL C2+ D5 PJ4 I Analog Analog comparator 2 positive input. C2- C5 PJ5 I Analog Analog comparator 2 negative input. C2o L10 C11 PF2 (9) PK6 (8) O TTL Analog comparator 2 output. CAN0Rx B6 A5 M9 A8 PB4 (8) PE4 (8) PF0 (3) PN0 (1) I TTL CAN module 0 receive. Analog comparator 1 output. 1374 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description CAN0Tx A6 B5 K10 B8 PB5 (8) PE5 (8) PF3 (3) PN1 (1) O TTL CAN module 0 transmit. CAN1Rx L3 A7 PA0 (8) PE6 (8) I TTL CAN module 1 receive. CAN1Tx M1 B7 PA1 (8) PE7 (8) O TTL CAN module 1 transmit. GND A1 J5 H5 J8 H9 J11 F9 D9 C7 E5 fixed - Power Ground reference for logic and I/O pins. GNDA C3 E3 fixed - Power The ground reference for the analog circuits (ADC, Analog Comparators, etc.). These are separated from GND to minimize the electrical noise contained on VDD from affecting the analog functions. GNDX K11 fixed - Power GND for the Hibernation oscillator. When using a crystal clock source, this pin should only be connected to the crystal load capacitors to improve oscillator immunity to system noise. When using an external oscillator, this pin should be connected to GND. HIB M12 fixed O TTL An output that indicates the processor is in Hibernate mode. I2C0SCL E10 PB2 (3) I/O OD I2C module 0 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C0SDA D13 PB3 (3) I/O OD I2C module 0 data. I2C1SCL M4 K7 PA6 (3) PG4 (3) I/O OD I2C module 1 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C1SDA N2 L7 PA7 (3) PG5 (3) I/O OD I2C module 1 data. I2C2SCL A5 N8 PE4 (3) PF6 (3) I/O OD I2C module 2 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C2SDA B5 M8 PE5 (3) PF7 (3) I/O OD I2C module 2 data. I2C3SCL B2 L8 PD0 (3) PG0 (3) I/O OD I2C module 3 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C3SDA B1 K8 PD1 (3) PG1 (3) I/O OD I2C module 3 data. I2C4SCL N7 PG2 (3) I/O OD I2C module 4 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. November 08, 2011 1375 Texas Instruments-Advance Information Signal Tables Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description I2C4SDA M7 PG3 (3) I/O OD I2C module 4 data. I2C5SCL F4 N4 PB6 (3) PG6 (3) I/O OD I2C module 5 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C5SDA F3 N3 PB7 (3) PG7 (3) I/O OD I2C module 5 data. IDX0 C1 L9 K4 A9 PD3 (6) PF4 (6) PH1 (5) PJ2 (5) I TTL QEI module 0 index. IDX1 L2 L7 N3 PC4 (6) PG5 (6) PG7 (5) I TTL QEI module 1 index. LPC0CLKRUN G11 PM2 (15) O TTL Application may optionally connect this pin to drive CLKRUN to wake a sleeping bus when wanted (or to prevent it from sleeping). LPC0FRAME D12 PL4 (15) I TTL This input signals the start or abort of a transaction. LPC0PD F13 PM0 (15) I TTL Power down and sleep signal from host. LPC0RESET C13 PL5 (15) I TTL LPC Bus reset signal. LPC0SCI F12 PM1 (15) O TTL Optional SCI interrupt for ACPI or other uses. M0FAULT0 C2 A3 L10 K3 B11 PD2 (4) PD6 (4) PF2 (4) PH0 (6) PK4 (6) I TTL Motion Control Module 0 PWM Fault 0. M0FAULT1 B3 K10 N7 K4 B12 PD7 (4) PF3 (4) PG2 (4) PH1 (6) PK5 (6) I TTL Motion Control Module 0 PWM Fault 1. M0FAULT2 L9 M7 J4 C11 PF4 (4) PG3 (4) PH2 (6) PK6 (6) I TTL Motion Control Module 0 PWM Fault 2. M0FAULT3 K9 J2 A12 PF5 (4) PH3 (6) PK7 (6) I TTL Motion Control Module 0 PWM Fault 3. M0PWM0 F4 K3 M13 PB6 (4) PH0 (4) PP0 (1) O TTL Motion Control Module 0 PWM 0. This signal is controlled by Module 0 PWM Generator 0. M0PWM1 F3 K4 L12 PB7 (4) PH1 (4) PP1 (1) O TTL Motion Control Module 0 PWM 1. This signal is controlled by Module 0 PWM Generator 0. M0PWM2 B6 J4 M5 PB4 (4) PH2 (4) PP2 (1) O TTL Motion Control Module 0 PWM 2. This signal is controlled by Module 0 PWM Generator 1. M0PWM3 A6 J2 J12 PB5 (4) PH3 (4) PP3 (1) O TTL Motion Control Module 0 PWM 3. This signal is controlled by Module 0 PWM Generator 1. 1376 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description M0PWM4 A5 K7 J3 H11 J13 PE4 (4) PG4 (4) PH4 (4) PM6 (2) PP4 (1) O TTL Motion Control Module 0 PWM 4. This signal is controlled by Module 0 PWM Generator 2. M0PWM5 B5 L7 H4 L13 L5 PE5 (4) PG5 (4) PH5 (4) PM7 (2) PP5 (1) O TTL Motion Control Module 0 PWM 5. This signal is controlled by Module 0 PWM Generator 2. M0PWM6 L2 B2 N4 H3 G3 D8 PC4 (4) PD0 (4) PG6 (4) PH6 (4) PN2 (2) PP6 (1) O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. M0PWM7 L1 B1 N3 G4 D10 K6 PC5 (4) PD1 (4) PG7 (4) PH7 (4) PN3 (2) PP7 (1) O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. M1FAULT0 L9 M8 G2 PF4 (5) PF7 (5) PK0 (6) I TTL Motion Control Module 1 PWM Fault 0. M1FAULT1 L8 G1 PG0 (5) PK1 (6) I TTL Motion Control Module 1 PWM Fault 1. M1FAULT2 K8 H1 PG1 (5) PK2 (6) I TTL Motion Control Module 1 PWM Fault 2. M1FAULT3 H2 PK3 (6) I TTL Motion Control Module 1 PWM Fault 3. M1PWM0 B2 N7 D4 PD0 (5) PG2 (5) PQ0 (1) O TTL Motion Control Module 1 PWM 0. This signal is controlled by Module 1 PWM Generator 0. M1PWM1 B1 M7 E4 PD1 (5) PG3 (5) PQ1 (1) O TTL Motion Control Module 1 PWM 1. This signal is controlled by Module 1 PWM Generator 0. M1PWM2 M4 A5 K7 F5 PA6 (5) PE4 (5) PG4 (5) PQ2 (1) O TTL Motion Control Module 1 PWM 2. This signal is controlled by Module 1 PWM Generator 1. M1PWM3 N2 B5 L7 N5 PA7 (5) PE5 (5) PG5 (5) PQ3 (1) O TTL Motion Control Module 1 PWM 3. This signal is controlled by Module 1 PWM Generator 1. M1PWM4 M9 L11 N6 PF0 (5) PN4 (2) PQ4 (1) O TTL Motion Control Module 1 PWM 4. This signal is controlled by Module 1 PWM Generator 2. M1PWM5 N9 N12 K5 PF1 (5) PN5 (2) PQ5 (1) O TTL Motion Control Module 1 PWM 5. This signal is controlled by Module 1 PWM Generator 2. November 08, 2011 1377 Texas Instruments-Advance Information Signal Tables Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description M1PWM6 L10 N11 M6 PF2 (5) PN6 (2) PQ6 (1) O TTL Motion Control Module 1 PWM 6. This signal is controlled by Module 1 PWM Generator 3. M1PWM7 K10 M11 L6 PF3 (5) PN7 (2) PQ7 (1) O TTL Motion Control Module 1 PWM 7. This signal is controlled by Module 1 PWM Generator 3. NC A2 fixed - - NMI B3 M9 PD7 (8) PF0 (8) I TTL OSC0 G12 fixed I Analog Main oscillator crystal input or an external clock reference input. OSC1 G13 fixed O Analog Main oscillator crystal output. Leave unconnected when using a single-ended clock source. No connect. Leave the pin electrically unconnected/isolated. Non-maskable interrupt. PA0 L3 - I/O TTL GPIO port A bit 0. PA1 M1 - I/O TTL GPIO port A bit 1. PA2 M2 - I/O TTL GPIO port A bit 2. PA3 M3 - I/O TTL GPIO port A bit 3. PA4 L4 - I/O TTL GPIO port A bit 4. PA5 N1 - I/O TTL GPIO port A bit 5. PA6 M4 - I/O TTL GPIO port A bit 6. PA7 N2 - I/O TTL GPIO port A bit 7. PB0 F11 - I/O TTL GPIO port B bit 0. This pin is not 5-V tolerant. PB1 E11 - I/O TTL GPIO port B bit 1. This pin is not 5-V tolerant. PB2 E10 - I/O TTL GPIO port B bit 2. PB3 D13 - I/O TTL GPIO port B bit 3. PB4 B6 - I/O TTL GPIO port B bit 4. PB5 A6 - I/O TTL GPIO port B bit 5. PB6 F4 - I/O TTL GPIO port B bit 6. PB7 F3 - I/O TTL GPIO port B bit 7. PC0 C10 - I/O TTL GPIO port C bit 0. PC1 A10 - I/O TTL GPIO port C bit 1. PC2 B10 - I/O TTL GPIO port C bit 2. PC3 A11 - I/O TTL GPIO port C bit 3. PC4 L2 - I/O TTL GPIO port C bit 4. PC5 L1 - I/O TTL GPIO port C bit 5. PC6 K1 - I/O TTL GPIO port C bit 6. PC7 K2 - I/O TTL GPIO port C bit 7. PD0 B2 - I/O TTL GPIO port D bit 0. PD1 B1 - I/O TTL GPIO port D bit 1. PD2 C2 - I/O TTL GPIO port D bit 2. PD3 C1 - I/O TTL GPIO port D bit 3. PD4 A4 - I/O TTL GPIO port D bit 4. 1378 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-3. Signals by Signal Name (continued) Pin Name PD5 Pin Number Pin Mux / Pin Assignment B4 - a Pin Type Buffer Type I/O TTL Description GPIO port D bit 5. PD6 A3 - I/O TTL GPIO port D bit 6. PD7 B3 - I/O TTL GPIO port D bit 7. PE0 F1 - I/O TTL GPIO port E bit 0. PE1 F2 - I/O TTL GPIO port E bit 1. PE2 E1 - I/O TTL GPIO port E bit 2. PE3 E2 - I/O TTL GPIO port E bit 3. PE4 A5 - I/O TTL GPIO port E bit 4. PE5 B5 - I/O TTL GPIO port E bit 5. PE6 A7 - I/O TTL GPIO port E bit 6. PE7 B7 - I/O TTL GPIO port E bit 7. PF0 M9 - I/O TTL GPIO port F bit 0. PF1 N9 - I/O TTL GPIO port F bit 1. PF2 L10 - I/O TTL GPIO port F bit 2. PF3 K10 - I/O TTL GPIO port F bit 3. PF4 L9 - I/O TTL GPIO port F bit 4. PF5 K9 - I/O TTL GPIO port F bit 5. PF6 N8 - I/O TTL GPIO port F bit 6. PF7 M8 - I/O TTL GPIO port F bit 7. PG0 L8 - I/O TTL GPIO port G bit 0. PG1 K8 - I/O TTL GPIO port G bit 1. PG2 N7 - I/O TTL GPIO port G bit 2. PG3 M7 - I/O TTL GPIO port G bit 3. PG4 K7 - I/O TTL GPIO port G bit 4. PG5 L7 - I/O TTL GPIO port G bit 5. PG6 N4 - I/O TTL GPIO port G bit 6. PG7 N3 - I/O TTL GPIO port G bit 7. PH0 K3 - I/O TTL GPIO port H bit 0. PH1 K4 - I/O TTL GPIO port H bit 1. PH2 J4 - I/O TTL GPIO port H bit 2. PH3 J2 - I/O TTL GPIO port H bit 3. PH4 J3 - I/O TTL GPIO port H bit 4. PH5 H4 - I/O TTL GPIO port H bit 5. PH6 H3 - I/O TTL GPIO port H bit 6. PH7 G4 - I/O TTL GPIO port H bit 7. PhA0 A3 M9 J3 PD6 (6) PF0 (6) PH4 (5) I TTL QEI module 0 phase A. PhA1 L1 L8 M7 PC5 (6) PG0 (6) PG3 (6) I TTL QEI module 1 phase A. November 08, 2011 1379 Texas Instruments-Advance Information Signal Tables Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description PhB0 B3 N9 H4 PD7 (6) PF1 (6) PH5 (5) I TTL QEI module 0 phase B. PhB1 K1 K8 K7 PC6 (6) PG1 (6) PG4 (6) I TTL QEI module 1 phase B. PJ0 C9 - I/O TTL GPIO port J bit 0. PJ1 B9 - I/O TTL GPIO port J bit 1. PJ2 A9 - I/O TTL GPIO port J bit 2. PJ3 C8 - I/O TTL GPIO port J bit 3. PJ4 D5 - I/O TTL GPIO port J bit 4. PJ5 C5 - I/O TTL GPIO port J bit 5. PJ6 C6 - I/O TTL GPIO port J bit 6. PJ7 C4 - I/O TTL GPIO port J bit 7. PK0 G2 - I/O TTL GPIO port K bit 0. PK1 G1 - I/O TTL GPIO port K bit 1. PK2 H1 - I/O TTL GPIO port K bit 2. PK3 H2 - I/O TTL GPIO port K bit 3. PK4 B11 - I/O TTL GPIO port K bit 4. PK5 B12 - I/O TTL GPIO port K bit 5. PK6 C11 - I/O TTL GPIO port K bit 6. PK7 A12 - I/O TTL GPIO port K bit 7. PL0 D11 - I/O TTL GPIO port L bit 0. PL1 C12 - I/O TTL GPIO port L bit 1. PL2 A13 - I/O TTL GPIO port L bit 2. PL3 B13 - I/O TTL GPIO port L bit 3. PL4 D12 - I/O TTL GPIO port L bit 4. PL5 C13 - I/O TTL GPIO port L bit 5. PL6 E12 - I/O TTL GPIO port L bit 6. PL7 E13 - I/O TTL GPIO port L bit 7. PM0 F13 - I/O TTL GPIO port M bit 0. PM1 F12 - I/O TTL GPIO port M bit 1. PM2 G11 - I/O TTL GPIO port M bit 2. PM3 H10 - I/O TTL GPIO port M bit 3. PM4 H13 - I/O TTL GPIO port M bit 4. PM5 H12 - I/O TTL GPIO port M bit 5. PM6 H11 - I/O TTL GPIO port M bit 6. PM7 L13 - I/O TTL GPIO port M bit 7. PN0 A8 - I/O TTL GPIO port N bit 0. PN1 B8 - I/O TTL GPIO port N bit 1. PN2 G3 - I/O TTL GPIO port N bit 2. PN3 D10 - I/O TTL GPIO port N bit 3. 1380 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment PN4 L11 - a Pin Type Buffer Type I/O TTL Description GPIO port N bit 4. PN5 N12 - I/O TTL GPIO port N bit 5. PN6 N11 - I/O TTL GPIO port N bit 6. PN7 M11 - I/O TTL GPIO port N bit 7. PP0 M13 - I/O TTL GPIO port P bit 0. PP1 L12 - I/O TTL GPIO port P bit 1. PP2 M5 - I/O TTL GPIO port P bit 2. PP3 J12 - I/O TTL GPIO port P bit 3. PP4 J13 - I/O TTL GPIO port P bit 4. PP5 L5 - I/O TTL GPIO port P bit 5. PP6 D8 - I/O TTL GPIO port P bit 6. PP7 K6 - I/O TTL GPIO port P bit 7. PQ0 D4 - I/O TTL GPIO port Q bit 0. PQ1 E4 - I/O TTL GPIO port Q bit 1. PQ2 F5 - I/O TTL GPIO port Q bit 2. PQ3 N5 - I/O TTL GPIO port Q bit 3. PQ4 N6 - I/O TTL GPIO port Q bit 4. PQ5 K5 - I/O TTL GPIO port Q bit 5. PQ6 M6 - I/O TTL GPIO port Q bit 6. PQ7 L6 - I/O TTL GPIO port Q bit 7. RST G10 fixed I TTL System reset input. RTCCLK B11 PK4 (7) O TTL Buffered version of the Hibernation module's 32.768-kHz clock. This signal is not output when the part is in Hibernation mode. SSI0Clk M2 PA2 (2) I/O TTL SSI module 0 clock. SSI0Fss M3 PA3 (2) I/O TTL SSI module 0 frame. SSI0Rx L4 PA4 (2) I TTL SSI module 0 receive. SSI0Tx N1 PA5 (2) O TTL SSI module 0 transmit. SSI1Clk B2 L10 PD0 (2) PF2 (2) I/O TTL SSI module 1 clock. SSI1Fss B1 K10 PD1 (2) PF3 (2) I/O TTL SSI module 1 frame. SSI1Rx C2 M9 PD2 (2) PF0 (2) I TTL SSI module 1 receive. SSI1Tx C1 N9 PD3 (2) PF1 (2) O TTL SSI module 1 transmit. SSI2Clk B6 J3 PB4 (2) PH4 (2) I/O TTL SSI module 2 clock. SSI2Fss A6 H4 PB5 (2) PH5 (2) I/O TTL SSI module 2 frame. SSI2Rx F4 H3 PB6 (2) PH6 (2) I TTL SSI module 2 receive. SSI2Tx F3 G4 PB7 (2) PH7 (2) O TTL SSI module 2 transmit. November 08, 2011 1381 Texas Instruments-Advance Information Signal Tables Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description SSI3Clk B2 K3 G2 PD0 (1) PH0 (2) PK0 (2) I/O TTL SSI module 3 clock. SSI3Fss B1 K4 G1 PD1 (1) PH1 (2) PK1 (2) I/O TTL SSI module 3 frame. SSI3Rx C2 J4 H1 PD2 (1) PH2 (2) PK2 (2) I TTL SSI module 3 receive. SSI3Tx C1 J2 H2 PD3 (1) PH3 (2) PK3 (2) O TTL SSI module 3 transmit. SWCLK C10 PC0 (1) I TTL JTAG/SWD CLK. SWDIO A10 PC1 (1) I/O TTL JTAG TMS and SWDIO. SWO A11 PC3 (1) O TTL JTAG TDO and SWO. T0CCP0 F4 M9 D11 PB6 (7) PF0 (7) PL0 (7) I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 0. T0CCP1 F3 N9 C12 PB7 (7) PF1 (7) PL1 (7) I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 1. T1CCP0 B6 L10 C9 A13 PB4 (7) PF2 (7) PJ0 (7) PL2 (7) I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 0. T1CCP1 A6 K10 B9 B13 PB5 (7) PF3 (7) PJ1 (7) PL3 (7) I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 1. T2CCP0 F11 L9 A9 D12 PB0 (7) PF4 (7) PJ2 (7) PL4 (7) I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 0. T2CCP1 E11 K9 C8 C13 PB1 (7) PF5 (7) PJ3 (7) PL5 (7) I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 1. T3CCP0 E10 N8 D5 E12 PB2 (7) PF6 (7) PJ4 (7) PL6 (7) I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 0. T3CCP1 D13 M8 C5 E13 PB3 (7) PF7 (7) PJ5 (7) PL7 (7) I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 1. T4CCP0 C10 L8 F13 M13 PC0 (7) PG0 (7) PM0 (7) PP0 (7) I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 0. 1382 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description T4CCP1 A10 K8 F12 L12 PC1 (7) PG1 (7) PM1 (7) PP1 (7) I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 1. T5CCP0 B10 N7 G11 M5 PC2 (7) PG2 (7) PM2 (7) PP2 (7) I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 0. T5CCP1 A11 M7 H10 J12 PC3 (7) PG3 (7) PM3 (7) PP3 (7) I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 1. TCK C10 PC0 (1) I TTL JTAG/SWD CLK. TDI B10 PC2 (1) I TTL JTAG TDI. TDO A11 PC3 (1) O TTL JTAG TDO and SWO. TMS A10 PC1 (1) I TTL JTAG TMS and SWDIO. TRCLK K10 PF3 (14) O TTL Trace clock. TRD0 L10 PF2 (14) O TTL Trace data 0. TRD1 N9 PF1 (14) O TTL Trace data 1. TRD2 M9 PF0 (14) O TTL Trace data 2. TRD3 L9 PF4 (14) O TTL Trace data 3. U0Rx L3 PA0 (1) I TTL UART module 0 receive. U0Tx M1 PA1 (1) O TTL UART module 0 transmit. U1CTS L1 N9 PC5 (8) PF1 (1) I TTL UART module 1 Clear To Send modem flow control input signal. U1DCD L10 PF2 (1) I TTL UART module 1 Data Carrier Detect modem status input signal. U1DSR K10 PF3 (1) I TTL UART module 1 Data Set Ready modem output control line. U1DTR L9 PF4 (1) O TTL UART module 1 Data Terminal Ready modem status input signal. U1RI B7 PE7 (1) I TTL UART module 1 Ring Indicator modem status input signal. U1RTS L2 M9 PC4 (8) PF0 (1) O TTL UART module 1 Request to Send modem flow control output line. U1Rx F11 L2 PB0 (1) PC4 (2) I TTL UART module 1 receive. U1Tx E11 L1 PB1 (1) PC5 (2) O TTL UART module 1 transmit. U2Rx A3 K7 PD6 (1) PG4 (1) I TTL UART module 2 receive. U2Tx B3 L7 PD7 (1) PG5 (1) O TTL UART module 2 transmit. U3Rx K1 PC6 (1) I TTL UART module 3 receive. U3Tx K2 PC7 (1) O TTL UART module 3 transmit. U4Rx L2 C9 PC4 (1) PJ0 (1) I TTL UART module 4 receive. November 08, 2011 1383 Texas Instruments-Advance Information Signal Tables Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description U4Tx L1 B9 PC5 (1) PJ1 (1) O TTL UART module 4 transmit. U5Rx A5 A9 PE4 (1) PJ2 (1) I TTL UART module 5 receive. U5Tx B5 C8 PE5 (1) PJ3 (1) O TTL UART module 5 transmit. U6Rx A4 D5 PD4 (1) PJ4 (1) I TTL UART module 6 receive. U6Tx B4 C5 PD5 (1) PJ5 (1) O TTL UART module 6 transmit. U7Rx F1 B11 PE0 (1) PK4 (1) I TTL UART module 7 receive. U7Tx F2 B12 PE1 (1) PK5 (1) O TTL UART module 7 transmit. USB0DM E13 PL7 I/O Analog Bidirectional differential data pin (D- per USB specification) for USB0. USB0DP E12 PL6 I/O Analog Bidirectional differential data pin (D+ per USB specification) for USB0. USB0EPEN K1 C2 L9 K7 PC6 (8) PD2 (8) PF4 (8) PG4 (8) O TTL Optionally used in Host mode to control an external power source to supply power to the USB bus. USB0ID F11 PB0 I Analog This signal senses the state of the USB ID signal. The USB PHY enables an integrated pull-up, and an external element (USB connector) indicates the initial state of the USB controller (pulled down is the A side of the cable and pulled up is the B side). USB0PFLT K2 C1 K9 L7 PC7 (8) PD3 (8) PF5 (8) PG5 (8) I TTL Optionally used in Host mode by an external power source to indicate an error state by that power source. USB0VBUS E11 PB1 I/O Analog This signal is used during the session request protocol. This signal allows the USB PHY to both sense the voltage level of VBUS, and pull up VBUS momentarily during VBUS pulsing. VBAT K12 fixed - Power Power source for the Hibernation module. It is normally connected to the positive terminal of a battery and serves as the battery backup/Hibernation module power-source supply. VDD E6 J7 J9 J10 F10 E9 E8 D7 fixed - Power Positive supply for I/O and some logic. 1384 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description VDDA D3 fixed - Power The positive supply (3.3 V) for the analog circuits (ADC, Analog Comparators, etc.). These are separated from VDD to minimize the electrical noise contained on VDD from affecting the analog functions. VDDA pins must be connected to 3.3 V, regardless of system implementation. VDDC J1 J6 K13 D6 fixed - Power Positive supply for most of the logic function, including the processor core and most peripherals. VREFA+ D2 fixed - Analog A reference voltage used to specify the voltage at which the ADC converts to a maximum value. This pin is used in conjunction with VREFA- which specifies the minimum value. In other words, the voltage that is applied to VREFA+ is the voltage with which an AINn signal is converted to 4095. The VREFA+ voltage is limited to the range specified in Table 25-24 on page 1422. VREFA- D1 fixed - Analog A reference voltage used to specify the input voltage at which the ADC converts to a minimum value. This pin is used in conjunction with VREFA+ which specifies the maximum value. In other words, the voltage that is applied to VREFA- is the voltage with which an AINn signal is converted to 0, while the voltage that is applied to VREFA+ is the voltage with which an AINn signal is converted to 4095. The VREFA- voltage is limited to the range specified in Table 25-24 on page 1422. WAKE N13 fixed I TTL An external input that brings the processor out of Hibernate mode when asserted. WT0CCP0 L2 K7 D11 H11 J13 PC4 (7) PG4 (7) PL0 (8) PM6 (7) PP4 (7) I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 0. WT0CCP1 L1 L7 C12 L13 L5 PC5 (7) PG5 (7) PL1 (8) PM7 (7) PP5 (7) I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 1. WT1CCP0 K1 N4 C11 A13 D8 PC6 (7) PG6 (7) PK6 (7) PL2 (8) PP6 (7) I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 0. WT1CCP1 K2 N3 A12 B13 K6 PC7 (7) PG7 (7) PK7 (7) PL3 (8) PP7 (7) I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 1. November 08, 2011 1385 Texas Instruments-Advance Information Signal Tables Table 23-3. Signals by Signal Name (continued) Pin Name Pin Number Pin Mux / Pin Assignment a Pin Type Buffer Type Description WT2CCP0 B2 K3 D12 G3 D4 PD0 (7) PH0 (7) PL4 (8) PN2 (7) PQ0 (7) I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 0. WT2CCP1 B1 K4 C13 D10 E4 PD1 (7) PH1 (7) PL5 (8) PN3 (7) PQ1 (7) I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 1. WT3CCP0 C2 J3 E12 L11 F5 PD2 (7) PH4 (7) PL6 (8) PN4 (7) PQ2 (7) I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 0. WT3CCP1 C1 H4 E13 N12 N5 PD3 (7) PH5 (7) PL7 (8) PN5 (7) PQ3 (7) I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 1. WT4CCP0 A4 H3 F13 N11 N6 PD4 (7) PH6 (7) PM0 (8) PN6 (7) PQ4 (7) I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 0. WT4CCP1 B4 G4 F12 M11 K5 PD5 (7) PH7 (7) PM1 (8) PN7 (7) PQ5 (7) I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 1. WT5CCP0 A3 J4 G11 M6 PD6 (7) PH2 (7) PM2 (8) PQ6 (7) I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 0. WT5CCP1 B3 J2 H10 L6 PD7 (7) PH3 (7) PM3 (8) PQ7 (7) I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 1. XOSC0 M10 fixed I Analog Hibernation module oscillator crystal input or an external clock reference input. Note that this is either a 32.768-kHz crystal or a 32.768-kHz oscillator for the Hibernation module RTC. XOSC1 N10 fixed O Analog Hibernation module oscillator crystal output. Leave unconnected when using a single-ended clock source. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 1386 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-4. Signals by Function, Except for GPIO Function ADC Pin Name a Pin Number Pin Type Buffer Type Description AIN0 E2 I Analog Analog-to-digital converter input 0. AIN1 E1 I Analog Analog-to-digital converter input 1. AIN2 F2 I Analog Analog-to-digital converter input 2. AIN3 F1 I Analog Analog-to-digital converter input 3. AIN4 B3 I Analog Analog-to-digital converter input 4. AIN5 A3 I Analog Analog-to-digital converter input 5. AIN6 B4 I Analog Analog-to-digital converter input 6. AIN7 A4 I Analog Analog-to-digital converter input 7. AIN8 B5 I Analog Analog-to-digital converter input 8. AIN9 A5 I Analog Analog-to-digital converter input 9. AIN10 B6 I Analog Analog-to-digital converter input 10. AIN11 A6 I Analog Analog-to-digital converter input 11. AIN12 C1 I Analog Analog-to-digital converter input 12. AIN13 C2 I Analog Analog-to-digital converter input 13. AIN14 B1 I Analog Analog-to-digital converter input 14. AIN15 B2 I Analog Analog-to-digital converter input 15. AIN16 G2 I Analog Analog-to-digital converter input 16. AIN17 G1 I Analog Analog-to-digital converter input 17. AIN18 H1 I Analog Analog-to-digital converter input 18. AIN19 H2 I Analog Analog-to-digital converter input 19. AIN20 B7 I Analog Analog-to-digital converter input 20. AIN21 A7 I Analog Analog-to-digital converter input 21. AIN22 B8 I Analog Analog-to-digital converter input 22. AIN23 A8 I Analog Analog-to-digital converter input 23. VREFA+ D2 - Analog A reference voltage used to specify the voltage at which the ADC converts to a maximum value. This pin is used in conjunction with VREFA- which specifies the minimum value. In other words, the voltage that is applied to VREFA+ is the voltage with which an AINn signal is converted to 4095. The VREFA+ voltage is limited to the range specified in Table 25-24 on page 1422. VREFA- D1 - Analog A reference voltage used to specify the input voltage at which the ADC converts to a minimum value. This pin is used in conjunction with VREFA+ which specifies the maximum value. In other words, the voltage that is applied to VREFA- is the voltage with which an AINn signal is converted to 0, while the voltage that is applied to VREFA+ is the voltage with which an AINn signal is converted to 4095. The VREFA- voltage is limited to the range specified in Table 25-24 on page 1422. November 08, 2011 1387 Texas Instruments-Advance Information Signal Tables Table 23-4. Signals by Function, Except for GPIO (continued) Function Analog Comparators Pin Name Pin Type Buffer Type C0+ K1 I Analog Analog comparator 0 positive input. C0- K2 I Analog Analog comparator 0 negative input. C0o M9 B11 O TTL C1+ L1 I Analog Analog comparator 1 positive input. Description Analog comparator 1 negative input. Analog comparator 0 output. C1- L2 I Analog C1o N9 B12 O TTL C2+ D5 I Analog Analog comparator 2 positive input. C2- C5 I Analog Analog comparator 2 negative input. C2o L10 C11 O TTL Analog comparator 2 output. CAN0Rx B6 A5 M9 A8 I TTL CAN module 0 receive. CAN0Tx A6 B5 K10 B8 O TTL CAN module 0 transmit. CAN1Rx L3 A7 I TTL CAN module 1 receive. CAN1Tx M1 B7 O TTL CAN module 1 transmit. TRCLK K10 O TTL Trace clock. TRD0 L10 O TTL Trace data 0. TRD1 N9 O TTL Trace data 1. TRD2 M9 O TTL Trace data 2. TRD3 L9 O TTL Trace data 3. Controller Area Network Core a Pin Number Analog comparator 1 output. 1388 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-4. Signals by Function, Except for GPIO (continued) Function General-Purpose Timers Pin Name a Pin Number Pin Type Buffer Type T0CCP0 F4 M9 D11 I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 0. T0CCP1 F3 N9 C12 I/O TTL 16/32-Bit Timer 0 Capture/Compare/PWM 1. T1CCP0 B6 L10 C9 A13 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 0. T1CCP1 A6 K10 B9 B13 I/O TTL 16/32-Bit Timer 1 Capture/Compare/PWM 1. T2CCP0 F11 L9 A9 D12 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 0. T2CCP1 E11 K9 C8 C13 I/O TTL 16/32-Bit Timer 2 Capture/Compare/PWM 1. T3CCP0 E10 N8 D5 E12 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 0. T3CCP1 D13 M8 C5 E13 I/O TTL 16/32-Bit Timer 3 Capture/Compare/PWM 1. T4CCP0 C10 L8 F13 M13 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 0. T4CCP1 A10 K8 F12 L12 I/O TTL 16/32-Bit Timer 4 Capture/Compare/PWM 1. T5CCP0 B10 N7 G11 M5 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 0. T5CCP1 A11 M7 H10 J12 I/O TTL 16/32-Bit Timer 5 Capture/Compare/PWM 1. WT0CCP0 L2 K7 D11 H11 J13 I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 0. I/O TTL 32/64-Bit Wide Timer 0 Capture/Compare/PWM 1. WT0CCP1 Description November 08, 2011 1389 Texas Instruments-Advance Information Signal Tables Table 23-4. Signals by Function, Except for GPIO (continued) Function Pin Name Pin Number a Pin Type Buffer Type Description L1 L7 C12 L13 L5 WT1CCP0 K1 N4 C11 A13 D8 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 0. WT1CCP1 K2 N3 A12 B13 K6 I/O TTL 32/64-Bit Wide Timer 1 Capture/Compare/PWM 1. WT2CCP0 B2 K3 D12 G3 D4 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 0. WT2CCP1 B1 K4 C13 D10 E4 I/O TTL 32/64-Bit Wide Timer 2 Capture/Compare/PWM 1. WT3CCP0 C2 J3 E12 L11 F5 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 0. WT3CCP1 C1 H4 E13 N12 N5 I/O TTL 32/64-Bit Wide Timer 3 Capture/Compare/PWM 1. WT4CCP0 A4 H3 F13 N11 N6 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 0. WT4CCP1 B4 G4 F12 M11 K5 I/O TTL 32/64-Bit Wide Timer 4 Capture/Compare/PWM 1. WT5CCP0 A3 J4 G11 M6 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 0. WT5CCP1 B3 J2 H10 L6 I/O TTL 32/64-Bit Wide Timer 5 Capture/Compare/PWM 1. 1390 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-4. Signals by Function, Except for GPIO (continued) Function Hibernate Pin Name a Pin Number Pin Type Buffer Type Description GNDX K11 - Power GND for the Hibernation oscillator. When using a crystal clock source, this pin should only be connected to the crystal load capacitors to improve oscillator immunity to system noise. When using an external oscillator, this pin should be connected to GND. HIB M12 O TTL An output that indicates the processor is in Hibernate mode. RTCCLK B11 O TTL Buffered version of the Hibernation module's 32.768-kHz clock. This signal is not output when the part is in Hibernation mode. VBAT K12 - Power Power source for the Hibernation module. It is normally connected to the positive terminal of a battery and serves as the battery backup/Hibernation module power-source supply. WAKE N13 I TTL An external input that brings the processor out of Hibernate mode when asserted. XOSC0 M10 I Analog Hibernation module oscillator crystal input or an external clock reference input. Note that this is either a 32.768-kHz crystal or a 32.768-kHz oscillator for the Hibernation module RTC. XOSC1 N10 O Analog Hibernation module oscillator crystal output. Leave unconnected when using a single-ended clock source. November 08, 2011 1391 Texas Instruments-Advance Information Signal Tables Table 23-4. Signals by Function, Except for GPIO (continued) Function Pin Name LPC Pin Type a Buffer Type Description I2C0SCL E10 I/O OD I2C I2C0SDA D13 I/O OD I2C module 0 data. I2C1SCL M4 K7 I/O OD I2C module 1 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C1SDA N2 L7 I/O OD I2C module 1 data. I2C2SCL A5 N8 I/O OD I2C module 2 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C2SDA B5 M8 I/O OD I2C module 2 data. I2C3SCL B2 L8 I/O OD I2C module 3 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C3SDA B1 K8 I/O OD I2C module 3 data. I2C4SCL N7 I/O OD I2C module 4 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C4SDA M7 I/O OD I2C module 4 data. I2C5SCL F4 N4 I/O OD I2C module 5 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. I2C5SDA F3 N3 I/O OD I2C module 5 data. SWCLK C10 I TTL JTAG/SWD CLK. SWDIO A10 I/O TTL JTAG TMS and SWDIO. I2C JTAG/SWD/SWO Pin Number module 0 clock. Note that this signal has an active pull-up. The corresponding port pin should not be configured as open drain. SWO A11 O TTL JTAG TDO and SWO. TCK C10 I TTL JTAG/SWD CLK. TDI B10 I TTL JTAG TDI. TDO A11 O TTL JTAG TDO and SWO. TMS A10 I TTL JTAG TMS and SWDIO. LPC0CLKRUN G11 O TTL Application may optionally connect this pin to drive CLKRUN to wake a sleeping bus when wanted (or to prevent it from sleeping). LPC0FRAME D12 I TTL This input signals the start or abort of a transaction. LPC0PD F13 I TTL Power down and sleep signal from host. LPC0RESET C13 I TTL LPC Bus reset signal. LPC0SCI F12 O TTL Optional SCI interrupt for ACPI or other uses. 1392 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-4. Signals by Function, Except for GPIO (continued) Function PWM Pin Name a Pin Number Pin Type Buffer Type Description M0FAULT0 C2 A3 L10 K3 B11 I TTL Motion Control Module 0 PWM Fault 0. M0FAULT1 B3 K10 N7 K4 B12 I TTL Motion Control Module 0 PWM Fault 1. M0FAULT2 L9 M7 J4 C11 I TTL Motion Control Module 0 PWM Fault 2. M0FAULT3 K9 J2 A12 I TTL Motion Control Module 0 PWM Fault 3. M0PWM0 F4 K3 M13 O TTL Motion Control Module 0 PWM 0. This signal is controlled by Module 0 PWM Generator 0. M0PWM1 F3 K4 L12 O TTL Motion Control Module 0 PWM 1. This signal is controlled by Module 0 PWM Generator 0. M0PWM2 B6 J4 M5 O TTL Motion Control Module 0 PWM 2. This signal is controlled by Module 0 PWM Generator 1. M0PWM3 A6 J2 J12 O TTL Motion Control Module 0 PWM 3. This signal is controlled by Module 0 PWM Generator 1. M0PWM4 A5 K7 J3 H11 J13 O TTL Motion Control Module 0 PWM 4. This signal is controlled by Module 0 PWM Generator 2. M0PWM5 B5 L7 H4 L13 L5 O TTL Motion Control Module 0 PWM 5. This signal is controlled by Module 0 PWM Generator 2. M0PWM6 L2 B2 N4 H3 G3 D8 O TTL Motion Control Module 0 PWM 6. This signal is controlled by Module 0 PWM Generator 3. M0PWM7 L1 B1 N3 G4 D10 K6 O TTL Motion Control Module 0 PWM 7. This signal is controlled by Module 0 PWM Generator 3. M1FAULT0 L9 M8 G2 I TTL Motion Control Module 1 PWM Fault 0. November 08, 2011 1393 Texas Instruments-Advance Information Signal Tables Table 23-4. Signals by Function, Except for GPIO (continued) Function Pin Name a Pin Number Pin Type Buffer Type Description M1FAULT1 L8 G1 I TTL Motion Control Module 1 PWM Fault 1. M1FAULT2 K8 H1 I TTL Motion Control Module 1 PWM Fault 2. M1FAULT3 H2 I TTL Motion Control Module 1 PWM Fault 3. M1PWM0 B2 N7 D4 O TTL Motion Control Module 1 PWM 0. This signal is controlled by Module 1 PWM Generator 0. M1PWM1 B1 M7 E4 O TTL Motion Control Module 1 PWM 1. This signal is controlled by Module 1 PWM Generator 0. M1PWM2 M4 A5 K7 F5 O TTL Motion Control Module 1 PWM 2. This signal is controlled by Module 1 PWM Generator 1. M1PWM3 N2 B5 L7 N5 O TTL Motion Control Module 1 PWM 3. This signal is controlled by Module 1 PWM Generator 1. M1PWM4 M9 L11 N6 O TTL Motion Control Module 1 PWM 4. This signal is controlled by Module 1 PWM Generator 2. M1PWM5 N9 N12 K5 O TTL Motion Control Module 1 PWM 5. This signal is controlled by Module 1 PWM Generator 2. M1PWM6 L10 N11 M6 O TTL Motion Control Module 1 PWM 6. This signal is controlled by Module 1 PWM Generator 3. M1PWM7 K10 M11 L6 O TTL Motion Control Module 1 PWM 7. This signal is controlled by Module 1 PWM Generator 3. 1394 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-4. Signals by Function, Except for GPIO (continued) Function Pin Name a Pin Number Pin Type Buffer Type GND A1 J5 H5 J8 H9 J11 F9 D9 C7 E5 - Power Ground reference for logic and I/O pins. GNDA C3 E3 - Power The ground reference for the analog circuits (ADC, Analog Comparators, etc.). These are separated from GND to minimize the electrical noise contained on VDD from affecting the analog functions. VDD E6 J7 J9 J10 F10 E9 E8 D7 - Power Positive supply for I/O and some logic. VDDA D3 - Power The positive supply (3.3 V) for the analog circuits (ADC, Analog Comparators, etc.). These are separated from VDD to minimize the electrical noise contained on VDD from affecting the analog functions. VDDA pins must be connected to 3.3 V, regardless of system implementation. VDDC J1 J6 K13 D6 - Power Positive supply for most of the logic function, including the processor core and most peripherals. IDX0 C1 L9 K4 A9 I TTL QEI module 0 index. IDX1 L2 L7 N3 I TTL QEI module 1 index. PhA0 A3 M9 J3 I TTL QEI module 0 phase A. PhA1 L1 L8 M7 I TTL QEI module 1 phase A. PhB0 B3 N9 H4 I TTL QEI module 0 phase B. PhB1 K1 K8 K7 I TTL QEI module 1 phase B. Power QEI Description November 08, 2011 1395 Texas Instruments-Advance Information Signal Tables Table 23-4. Signals by Function, Except for GPIO (continued) Function Pin Name a Pin Number Pin Type Buffer Type SSI0Clk M2 I/O TTL SSI module 0 clock. SSI0Fss M3 I/O TTL SSI module 0 frame. SSI0Rx L4 I TTL SSI module 0 receive. SSI0Tx N1 O TTL SSI module 0 transmit. SSI1Clk B2 L10 I/O TTL SSI module 1 clock. SSI1Fss B1 K10 I/O TTL SSI module 1 frame. SSI1Rx C2 M9 I TTL SSI module 1 receive. SSI1Tx C1 N9 O TTL SSI module 1 transmit. SSI2Clk B6 J3 I/O TTL SSI module 2 clock. SSI2Fss A6 H4 I/O TTL SSI module 2 frame. SSI2Rx F4 H3 I TTL SSI module 2 receive. SSI2Tx F3 G4 O TTL SSI module 2 transmit. SSI3Clk B2 K3 G2 I/O TTL SSI module 3 clock. SSI3Fss B1 K4 G1 I/O TTL SSI module 3 frame. SSI3Rx C2 J4 H1 I TTL SSI module 3 receive. SSI3Tx C1 J2 H2 O TTL SSI module 3 transmit. NMI B3 M9 I TTL Non-maskable interrupt. OSC0 G12 I Analog Main oscillator crystal input or an external clock reference input. OSC1 G13 O Analog Main oscillator crystal output. Leave unconnected when using a single-ended clock source. RST G10 I TTL SSI System Control & Clocks Description System reset input. 1396 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-4. Signals by Function, Except for GPIO (continued) Function Pin Name Pin Number a Pin Type Buffer Type Description U0Rx L3 I TTL UART module 0 receive. U0Tx M1 O TTL UART module 0 transmit. U1CTS L1 N9 I TTL UART module 1 Clear To Send modem flow control input signal. U1DCD L10 I TTL UART module 1 Data Carrier Detect modem status input signal. U1DSR K10 I TTL UART module 1 Data Set Ready modem output control line. U1DTR L9 O TTL UART module 1 Data Terminal Ready modem status input signal. U1RI B7 I TTL UART module 1 Ring Indicator modem status input signal. U1RTS L2 M9 O TTL UART module 1 Request to Send modem flow control output line. U1Rx F11 L2 I TTL UART module 1 receive. U1Tx E11 L1 O TTL UART module 1 transmit. U2Rx A3 K7 I TTL UART module 2 receive. U2Tx B3 L7 O TTL UART module 2 transmit. U3Rx K1 I TTL UART module 3 receive. U3Tx K2 O TTL UART module 3 transmit. U4Rx L2 C9 I TTL UART module 4 receive. U4Tx L1 B9 O TTL UART module 4 transmit. U5Rx A5 A9 I TTL UART module 5 receive. U5Tx B5 C8 O TTL UART module 5 transmit. U6Rx A4 D5 I TTL UART module 6 receive. U6Tx B4 C5 O TTL UART module 6 transmit. U7Rx F1 B11 I TTL UART module 7 receive. U7Tx F2 B12 O TTL UART module 7 transmit. UART November 08, 2011 1397 Texas Instruments-Advance Information Signal Tables Table 23-4. Signals by Function, Except for GPIO (continued) Function Pin Name a Pin Number Pin Type Buffer Type USB0DM E13 I/O Analog Bidirectional differential data pin (D- per USB specification) for USB0. USB0DP E12 I/O Analog Bidirectional differential data pin (D+ per USB specification) for USB0. USB0EPEN K1 C2 L9 K7 O TTL Optionally used in Host mode to control an external power source to supply power to the USB bus. USB0ID F11 I Analog This signal senses the state of the USB ID signal. The USB PHY enables an integrated pull-up, and an external element (USB connector) indicates the initial state of the USB controller (pulled down is the A side of the cable and pulled up is the B side). USB0PFLT K2 C1 K9 L7 I TTL Optionally used in Host mode by an external power source to indicate an error state by that power source. USB0VBUS E11 I/O Analog This signal is used during the session request protocol. This signal allows the USB PHY to both sense the voltage level of VBUS, and pull up VBUS momentarily during VBUS pulsing. USB Description a. The TTL designation indicates the pin has TTL-compatible voltage levels. Table 23-5. GPIO Pins and Alternate Functions a Digital Function (GPIOPCTL PMCx Bit Field Encoding) IO Pin Analog Function 1 2 3 4 5 6 7 8 9 14 15 PA0 L3 - U0Rx - - - - - - CAN1Rx - - - PA1 M1 - U0Tx - - - - - - CAN1Tx - - - PA2 M2 - - SSI0Clk - - - - - - - - - PA3 M3 - - SSI0Fss - - - - - - - - - PA4 L4 - - SSI0Rx - - - - - - - - - PA5 N1 - - SSI0Tx - - - - - - - - - PA6 M4 - - - I2C1SCL - M1PWM2 - - - - - - PA7 N2 - - - I2C1SDA - M1PWM3 - - - - - - PB0 F11 USB0ID U1Rx - - - - - T2CCP0 - - - - PB1 E11 USB0VBUS U1Tx - - - - - T2CCP1 - - - - PB2 E10 - - - I2C0SCL - - - T3CCP0 - - - - PB3 D13 - - - I2C0SDA - - - T3CCP1 - - - - PB4 B6 AIN10 - SSI2Clk - M0PWM2 - - T1CCP0 CAN0Rx - - - PB5 A6 AIN11 - SSI2Fss - M0PWM3 - - T1CCP1 CAN0Tx - - - PB6 F4 - - SSI2Rx I2C5SCL M0PWM0 - - T0CCP0 - - - - PB7 F3 - - SSI2Tx I2C5SDA M0PWM1 - - T0CCP1 - - - - PC0 C10 - TCK SWCLK - - - - - T4CCP0 - - - - PC1 A10 - TMS SWDIO - - - - - T4CCP1 - - - - PC2 B10 - TDI - - - - - T5CCP0 - - - - 1398 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-5. GPIO Pins and Alternate Functions (continued) a Digital Function (GPIOPCTL PMCx Bit Field Encoding) IO Pin Analog Function 1 2 3 4 5 6 7 8 9 14 15 PC3 A11 - TDO SWO - - - - - T5CCP1 - - - - PC4 L2 C1- U4Rx U1Rx - M0PWM6 - IDX1 WT0CCP0 U1RTS - - - PC5 L1 C1+ U4Tx U1Tx - M0PWM7 - PhA1 WT0CCP1 U1CTS - - - PC6 K1 C0+ U3Rx - - - - PhB1 WT1CCP0 USB0EPEN - - - PC7 K2 C0- U3Tx - - - - - WT1CCP1 USB0PFLT - - - PD0 B2 AIN15 SSI3Clk SSI1Clk I2C3SCL M0PWM6 M1PWM0 - WT2CCP0 - - - - - PD1 B1 AIN14 SSI3Fss SSI1Fss I2C3SDA M0PWM7 M1PWM1 - WT2CCP1 - - - PD2 C2 AIN13 SSI3Rx SSI1Rx - M0FAULT0 - - WT3CCP0 USB0EPEN - - - PD3 C1 AIN12 SSI3Tx SSI1Tx - - - IDX0 WT3CCP1 USB0PFLT - - - PD4 A4 AIN7 U6Rx - - - - - WT4CCP0 - - - - PD5 B4 AIN6 U6Tx - - - - - WT4CCP1 - - - - PD6 A3 AIN5 U2Rx - - M0FAULT0 - PhA0 WT5CCP0 - - - - PD7 B3 AIN4 U2Tx - - M0FAULT1 - PhB0 WT5CCP1 NMI - - - PE0 F1 AIN3 U7Rx - - - - - - - - - - PE1 F2 AIN2 U7Tx - - - - - - - - - - PE2 E1 AIN1 - - - - - - - - - - - - - - PE3 E2 AIN0 - - PE4 A5 AIN9 U5Rx - I2C2SCL M0PWM4 M1PWM2 PE5 B5 AIN8 U5Tx - I2C2SDA M0PWM5 M1PWM3 - - CAN0Tx - - - PE6 A7 AIN21 - - - - - - - CAN1Rx - - - PE7 B7 AIN20 U1RI - - - - - - CAN1Tx - - - PF0 M9 - U1RTS SSI1Rx CAN0Rx - M1PWM4 PhA0 T0CCP0 NMI C0o TRD2 - PF1 N9 - U1CTS SSI1Tx - - M1PWM5 PhB0 T0CCP1 - C1o TRD1 - PF2 L10 - U1DCD SSI1Clk - M0FAULT0 M1PWM6 - T1CCP0 - C2o TRD0 - PF3 K10 - U1DSR SSI1Fss CAN0Tx M0FAULT1 M1PWM7 - T1CCP1 - - TRCLK - PF4 L9 - U1DTR - - M0FAULT2 M1FAULT0 - - - - - - - - CAN0Rx - - - IDX0 T2CCP0 USB0EPEN - TRD3 - PF5 K9 - - - - M0FAULT3 - - T2CCP1 USB0PFLT - - - PF6 N8 - - - I2C2SCL - - - T3CCP0 - - - - PF7 M8 - - - I2C2SDA - M1FAULT0 - T3CCP1 - - - - PG0 L8 - - - I2C3SCL - M1FAULT1 PhA1 T4CCP0 - - - - PG1 K8 - - - I2C3SDA - M1FAULT2 PhB1 T4CCP1 - - - - PG2 N7 - - - I2C4SCL M0FAULT1 M1PWM0 - T5CCP0 - - - - PG3 M7 - - - I2C4SDA M0FAULT2 M1PWM1 PhA1 T5CCP1 - - - - PG4 K7 - U2Rx - I2C1SCL M0PWM4 M1PWM2 PhB1 WT0CCP0 USB0EPEN - - - IDX1 WT0CCP1 USB0PFLT PG5 L7 - U2Tx - I2C1SDA M0PWM5 M1PWM3 PG6 N4 - - - I2C5SCL M0PWM6 - - - - - WT1CCP0 - - - - PG7 N3 - - - I2C5SDA M0PWM7 IDX1 PH0 K3 - - SSI3Clk - M0PWM0 - - WT1CCP1 - - - - M0FAULT0 WT2CCP0 - - - - PH1 K4 - - SSI3Fss - M0PWM1 IDX0 M0FAULT1 WT2CCP1 - - - - November 08, 2011 1399 Texas Instruments-Advance Information Signal Tables Table 23-5. GPIO Pins and Alternate Functions (continued) a Digital Function (GPIOPCTL PMCx Bit Field Encoding) IO Pin Analog Function 1 2 3 4 5 8 9 14 15 PH2 J4 - - SSI3Rx - M0PWM2 - M0FAULT2 WT5CCP0 - - - - PH3 J2 - - SSI3Tx - M0PWM3 - M0FAULT3 WT5CCP1 - - - - PH4 J3 - - SSI2Clk - M0PWM4 PhA0 - WT3CCP0 - - - - PH5 H4 - - SSI2Fss - M0PWM5 PhB0 - WT3CCP1 - - - - PH6 H3 - - SSI2Rx - M0PWM6 - - WT4CCP0 - - - - PH7 G4 - - SSI2Tx - M0PWM7 - - WT4CCP1 - - - - PJ0 C9 - U4Rx - - - - - T1CCP0 - - - - 6 7 PJ1 B9 - U4Tx - - - - - T1CCP1 - - - - PJ2 A9 - U5Rx - - - IDX0 - T2CCP0 - - - - PJ3 C8 - U5Tx - - - - - T2CCP1 - - - - PJ4 D5 C2+ U6Rx - - - - - T3CCP0 - - - - PJ5 C5 C2- U6Tx - - - - - T3CCP1 - - - - PJ6 C6 - - - - - - - - - - - - PJ7 C4 - - - - - - - - - - - - PK0 G2 AIN16 - SSI3Clk - - - M1FAULT0 - - - - - PK1 G1 AIN17 - SSI3Fss - - - M1FAULT1 - - - - - PK2 H1 AIN18 - SSI3Rx - - - M1FAULT2 - - - - - PK3 H2 AIN19 - SSI3Tx - - - M1FAULT3 - PK4 B11 - U7Rx - - - - M0FAULT0 RTCCLK - - - - - C0o - - - PK5 B12 - U7Tx - - - - M0FAULT1 C1o - - - PK6 C11 - - - - - - M0FAULT2 WT1CCP0 C2o - - - PK7 A12 - - - - - - M0FAULT3 WT1CCP1 - - - - PL0 D11 - - - - - - - T0CCP0 WT0CCP0 - - - PL1 C12 - - - - - - - T0CCP1 WT0CCP1 - - - PL2 A13 - - - - - - - T1CCP0 WT1CCP0 - - - PL3 B13 - - - - - - - T1CCP1 WT1CCP1 - - - PL4 D12 - - - - - - - T2CCP0 WT2CCP0 - - LPC0FRAME PL5 C13 - - - - - - - T2CCP1 WT2CCP1 - - LPC0RESET PL6 E12 USB0DP - - - - - - T3CCP0 WT3CCP0 - - - PL7 E13 USB0DM - - - - - - T3CCP1 WT3CCP1 - - - PM0 F13 - - - - - - - T4CCP0 WT4CCP0 - - LPC0PD PM1 F12 - - - - - - - T4CCP1 WT4CCP1 - - LPC0SCI PM2 G11 - - - - - - - T5CCP0 WT5CCP0 - - LPC0CLKRUN PM3 H10 - - - - - - - T5CCP1 WT5CCP1 - - - PM4 H13 - - - - - - - PM5 H12 - - - - - - PM6 H11 - - M0PWM4 - - - - - - - - - - - - - - - WT0CCP0 - - - - PM7 L13 - - M0PWM5 - - - - WT0CCP1 - - - - PN0 A8 AIN23 CAN0Rx - - - - - - - - - - PN1 B8 AIN22 CAN0Tx - - - - - - - - - - 1400 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-5. GPIO Pins and Alternate Functions (continued) a Digital Function (GPIOPCTL PMCx Bit Field Encoding) IO Pin Analog Function 1 2 3 4 5 6 7 8 9 14 15 PN2 G3 - - M0PWM6 - - - - WT2CCP0 - - - - PN3 D10 - - M0PWM7 - - - - WT2CCP1 - - - - PN4 L11 - - M1PWM4 - - - - WT3CCP0 - - - - PN5 N12 - - M1PWM5 - - - - WT3CCP1 - - - - PN6 N11 - - M1PWM6 - - - - WT4CCP0 - - - - PN7 M11 - - M1PWM7 - - - - WT4CCP1 - - - - PP0 M13 - M0PWM0 - - - - - T4CCP0 - - - - PP1 L12 - M0PWM1 - - - - - T4CCP1 - - - - PP2 M5 - M0PWM2 - - - - - T5CCP0 - - - - PP3 J12 - M0PWM3 - - - - - T5CCP1 - - - - PP4 J13 - M0PWM4 - - - - - WT0CCP0 - - - - PP5 L5 - M0PWM5 - - - - - WT0CCP1 - - - - PP6 D8 - M0PWM6 - - - - - WT1CCP0 - - - - PP7 K6 - M0PWM7 - - - - - WT1CCP1 - - - - PQ0 D4 - M1PWM0 - - - - - WT2CCP0 - - - - PQ1 E4 - M1PWM1 - - - - - WT2CCP1 - - - - PQ2 F5 - M1PWM2 - - - - - WT3CCP0 - - - - PQ3 N5 - M1PWM3 - - - - - WT3CCP1 - - - - PQ4 N6 - M1PWM4 - - - - - WT4CCP0 - - - - PQ5 K5 - M1PWM5 - - - - - WT4CCP1 - - - - PQ6 M6 - M1PWM6 - - - - - WT5CCP0 - - - - PQ7 L6 - M1PWM7 - - - - - WT5CCP1 - - - - a. The digital signals that are shaded gray are the power-on default values for the corresponding GPIO pin. Encodings 10-13 are not used on this device. November 08, 2011 1401 Texas Instruments-Advance Information Signal Tables Table 23-6. Possible Pin Assignments for Alternate Functions # of Possible Assignments one Alternate Function GPIO Function AIN0 PE3 AIN1 PE2 AIN10 PB4 AIN11 PB5 AIN12 PD3 AIN13 PD2 AIN14 PD1 AIN15 PD0 AIN16 PK0 AIN17 PK1 AIN18 PK2 AIN19 PK3 AIN2 PE1 AIN20 PE7 AIN21 PE6 AIN22 PN1 AIN23 PN0 AIN3 PE0 AIN4 PD7 AIN5 PD6 AIN6 PD5 AIN7 PD4 AIN8 PE5 AIN9 PE4 C0+ PC6 C0- PC7 C1+ PC5 C1- PC4 C2+ PJ4 C2- PJ5 I2C0SCL PB2 I2C0SDA PB3 I2C4SCL PG2 I2C4SDA PG3 LPC0CLKRUN PM2 LPC0FRAME PL4 LPC0PD PM0 LPC0RESET PL5 LPC0SCI PM1 M1FAULT3 PK3 RTCCLK PK4 1402 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-6. Possible Pin Assignments for Alternate Functions (continued) # of Possible Assignments Alternate Function GPIO Function SSI0Clk PA2 SSI0Fss PA3 SSI0Rx PA4 SSI0Tx PA5 SWCLK PC0 SWDIO PC1 SWO PC3 TCK PC0 TDI PC2 TDO PC3 TMS PC1 TRCLK PF3 TRD0 PF2 TRD1 PF1 TRD2 PF0 TRD3 PF4 U0Rx PA0 U0Tx PA1 U1DCD PF2 U1DSR PF3 U1DTR PF4 U1RI PE7 U3Rx PC6 U3Tx PC7 USB0DM PL7 USB0DP PL6 USB0ID PB0 USB0VBUS PB1 November 08, 2011 1403 Texas Instruments-Advance Information Signal Tables Table 23-6. Possible Pin Assignments for Alternate Functions (continued) # of Possible Assignments Alternate Function GPIO Function C0o PF0 PK4 C1o PF1 PK5 C2o PF2 PK6 CAN1Rx PA0 PE6 CAN1Tx PA1 PE7 I2C1SCL PA6 PG4 I2C1SDA PA7 PG5 I2C2SCL PE4 PF6 I2C2SDA PE5 PF7 I2C3SCL PD0 PG0 I2C3SDA PD1 PG1 I2C5SCL PB6 PG6 I2C5SDA PB7 PG7 M1FAULT1 PG0 PK1 M1FAULT2 PG1 PK2 NMI PD7 PF0 SSI1Clk PD0 PF2 SSI1Fss PD1 PF3 SSI1Rx PD2 PF0 SSI1Tx PD3 PF1 SSI2Clk PB4 PH4 SSI2Fss PB5 PH5 SSI2Rx PB6 PH6 SSI2Tx PB7 PH7 U1CTS PC5 PF1 two U1RTS PC4 PF0 U1Rx PB0 PC4 U1Tx PB1 PC5 U2Rx PD6 PG4 U2Tx PD7 PG5 U4Rx PC4 PJ0 U4Tx PC5 PJ1 U5Rx PE4 PJ2 U5Tx PE5 PJ3 U6Rx PD4 PJ4 U6Tx PD5 PJ5 U7Rx PE0 PK4 U7Tx PE1 PK5 1404 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 23-6. Possible Pin Assignments for Alternate Functions (continued) # of Possible Assignments three Alternate Function GPIO Function IDX1 PC4 PG5 PG7 M0FAULT3 PF5 PH3 PK7 M0PWM0 PB6 PH0 PP0 M0PWM1 PB7 PH1 PP1 M0PWM2 PB4 PH2 PP2 M0PWM3 PB5 PH3 PP3 M1FAULT0 PF4 PF7 PK0 M1PWM0 PD0 PG2 PQ0 M1PWM1 PD1 PG3 PQ1 M1PWM4 PF0 PN4 PQ4 M1PWM5 PF1 PN5 PQ5 M1PWM6 PF2 PN6 PQ6 M1PWM7 PF3 PN7 PQ7 PhA0 PD6 PF0 PH4 PhA1 PC5 PG0 PG3 PhB0 PD7 PF1 PH5 PhB1 PC6 PG1 PG4 SSI3Clk PD0 PH0 PK0 SSI3Fss PD1 PH1 PK1 SSI3Rx PD2 PH2 PK2 SSI3Tx PD3 PH3 PK3 T0CCP0 PB6 PF0 PL0 T0CCP1 PB7 PF1 PL1 November 08, 2011 1405 Texas Instruments-Advance Information Signal Tables Table 23-6. Possible Pin Assignments for Alternate Functions (continued) # of Possible Assignments Alternate Function GPIO Function CAN0Rx PB4 PE4 PF0 PN0 CAN0Tx PB5 PE5 PF3 PN1 IDX0 PD3 PF4 PH1 PJ2 M0FAULT2 PF4 PG3 PH2 PK6 M1PWM2 PA6 PE4 PG4 PQ2 M1PWM3 PA7 PE5 PG5 PQ3 T1CCP0 PB4 PF2 PJ0 PL2 T1CCP1 PB5 PF3 PJ1 PL3 T2CCP0 PB0 PF4 PJ2 PL4 T2CCP1 PB1 PF5 PJ3 PL5 T3CCP0 PB2 PF6 PJ4 PL6 T3CCP1 PB3 PF7 PJ5 PL7 T4CCP0 PC0 PG0 PM0 PP0 T4CCP1 PC1 PG1 PM1 PP1 T5CCP0 PC2 PG2 PM2 PP2 four T5CCP1 PC3 PG3 PM3 PP3 USB0EPEN PC6 PD2 PF4 PG4 USB0PFLT PC7 PD3 PF5 PG5 WT5CCP0 PD6 PH2 PM2 PQ6 WT5CCP1 PD7 PH3 PM3 PQ7 M0FAULT0 PD2 PD6 PF2 PH0 PK4 M0FAULT1 PD7 PF3 PG2 PH1 PK5 M0PWM4 PE4 PG4 PH4 PM6 PP4 M0PWM5 PE5 PG5 PH5 PM7 PP5 WT0CCP0 PC4 PG4 PL0 PM6 PP4 WT0CCP1 PC5 PG5 PL1 PM7 PP5 WT1CCP0 PC6 PG6 PK6 PL2 PP6 WT1CCP1 PC7 PG7 PK7 PL3 PP7 WT2CCP0 PD0 PH0 PL4 PN2 PQ0 WT2CCP1 PD1 PH1 PL5 PN3 PQ1 WT3CCP0 PD2 PH4 PL6 PN4 PQ2 WT3CCP1 PD3 PH5 PL7 PN5 PQ3 WT4CCP0 PD4 PH6 PM0 PN6 PQ4 five WT4CCP1 PD5 PH7 PM1 PN7 PQ5 M0PWM6 PC4 PD0 PG6 PH6 PN2 PP6 M0PWM7 PC5 PD1 PG7 PH7 PN3 PP7 six 23.1 Connections for Unused Signals Table 23-7 on page 1407 show how to handle signals for functions that are not used in a particular system implementation for devices that are in a 157-ball BGA package. Two options are shown in the table: an acceptable practice and a preferred practice for reduced power consumption and improved EMC characteristics. If a module is not used in a system, and its inputs are grounded, it 1406 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller is important that the clock to the module is never enabled by setting the corresponding bit in the RCGCx register. Table 23-7. Connections for Unused Signals (157-Ball BGA) Function GPIO Signal Name System Control Acceptable Practice Preferred Practice All unused GPIOs - NC GND HIB M12 NC NC VBAT K12 NC VDD WAKE N13 NC GND XOSC0 M10 NC GND XOSC1 N10 NC NC GNDX K11 GND GND Hibernate No Connects Pin Number NC - NC NC OSC0 G12 NC GND OSC1 G13 NC NC RST G10 USB0DM E13 NC GND USB0DP E12 NC GND USB Pull up as shown in Figure Connect through a capacitor to 5-1 on page 217 GND as close to pin as possible November 08, 2011 1407 Texas Instruments-Advance Information Operating Characteristics 24 Operating Characteristics Table 24-1. Temperature Characteristics Characteristic Symbol Value Unit Industrial operating temperature range TA -40 to +85 °C Unpowered storage temperature range TS -65 to +150 °C Table 24-2. Thermal Characteristics Characteristic Symbol Value a c Junction temperature, -40 to +125 Maximum power dissipation Unit b Thermal resistance (junction to ambient) ΘJA 50 TJ °C/W TA + (P • ΘJA) °C d P 560 mW a. Junction to ambient thermal resistance θJA numbers are determined by a package simulator. b. Preliminary. c. Power dissipation is a function of temperature. d. Preliminary, pending characterization. a Table 24-3. ESD Absolute Maximum Ratings Parameter Name Min Nom Max Unit VESDHBM - VESDCDM - - 2.0 kV - 500 V ® a. All Stellaris parts are ESD tested following the JEDEC standard. 1408 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 25 Electrical Characteristics 25.1 Maximum Ratings The maximum ratings are the limits to which the device can be subjected without permanently damaging the device. Device reliability may be adversely affected by exposure to absolute-maximum ratings for extended periods. Note: The device is not guaranteed to operate properly at the maximum ratings. Table 25-1. Maximum Ratings Value a Parameter Parameter Name VDD Unit Min Max VDD supply voltage 0 4 V VDDA VDDA supply voltage 0 4 V VBAT VBAT battery supply voltage 0 4 V b Input voltage -0.3 5.5 V Input voltage for PB0 and PB1 when configured as GPIO -0.3 VDD + 0.3 V - 25 mA VIN IGPIOMAX INON Maximum current per output pin Maximum current into or out of a non-power pin when the microcontroller is unpowered - c pending mA a. Voltages are measured with respect to GND. b. Applies to static and dynamic signals including overshoot. c. Pending characterization. Important: This device contains circuitry to protect the inputs against damage due to high-static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are connected to an appropriate logic voltage level (see “Connections for Unused Signals” on page 1406). 25.2 Recommended Operating Conditions For special high-current applications, the GPIO output buffers may be used with the following restrictions. With the GPIO pins configured as 8-mA output drivers, a total of four GPIO outputs may be used to sink current loads up to 18 mA each. At 18-mA sink current loading, the VOL value is specified as 1.2 V. The high-current GPIO package pins must be selected such that there are only a maximum of two per side of the physical package or BGA pin group with the total number of high-current GPIO outputs not exceeding four for the entire package. Table 25-2. Recommended DC Operating Conditions Parameter Parameter Name Min Nom Max Unit VDD VDD supply voltage 2.97 3.3 3.63 V VDDA VDDA supply voltage 2.97 3.3 3.63 V VDDC VDDC supply voltage 1.08 1.2 1.32 V High-level input voltage 2.1 - 5.0 V VIH November 08, 2011 1409 Texas Instruments-Advance Information Electrical Characteristics Table 25-2. Recommended DC Operating Conditions (continued) Parameter Parameter Name Min Nom Max Unit VIL Low-level input voltage -0.3 - 1.2 V VOH High-level output voltage 2.4 - - V VOL Low-level output voltage - - 0.4 V 2-mA Drive 2.0 - - mA 4-mA Drive 4.0 - - mA 8-mA Drive 8.0 - - mA 2-mA Drive 2.0 - - mA 4-mA Drive 4.0 - - mA 8-mA Drive 8.0 - - mA 8-mA Drive, VOL=1.2 V 18.0 - - mA High-level source current, VOH=2.4 V IOH Low-level sink current, VOL=0.4 V IOL Table 25-3. GPIO Current Restrictions Parameter Parameter Name Min a IMAXL Cumulative maximum GPIO current per side, left Nom a - Max Unit b mA b mA b mA b mA 170 IMAXB Cumulative maximum GPIO current per side, bottom - - 150 IMAXR Cumulative maximum GPIO current per side, right a - - 140 IMAXT a Cumulative maximum GPIO current per side, top - - 160 a. Sum of sink and source current for GPIOs as shown in Table 25-4 on page 1410. b. Preliminary, pending characterization. Table 25-4. GPIO Package Side Assignments Side GPIOs Left PB[4-5], PC[0-3], PD[4-7], PE[4-7], PJ[0-7], PK[4-7], PN[0-1,3], PP6 Bottom PB[6-7], PC[4-7], PD[0-3], PE[0-3], PH[0-7], PK[0-3], PN2, PQ[0-2] Right PA[0-7], PF[0-7], PG[0-7], PN[4-7], PP[2,5,7], PQ[3-7], Top 25.3 PB[0-3], PL[0-7], PM[0-7], PP[0-3] Load Conditions Unless otherwise specified, the following conditions are true for all timing measurements. Figure 25-1. Load Conditions CL = 50 pF pin GND 1410 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 25.4 JTAG and Boundary Scan Table 25-5. JTAG Characteristics Parameter No. Parameter Parameter Name J1 FTCK TCK operational clock frequency J2 TTCK TCK operational clock period a Min Nom Max Unit 0 - 10 MHz 100 - - ns J3 TTCK_LOW TCK clock Low time - tTCK - ns J4 TTCK_HIGH TCK clock High time - tTCK - ns J5 TTCK_R TCK rise time 0 - 10 ns J6 TTCK_F TCK fall time 0 - 10 ns J7 TTMS_SU TMS setup time to TCK rise 8 - - ns J8 TTMS_HLD TMS hold time from TCK rise 4 - - ns J9 TTDI_SU TDI setup time to TCK rise 18 - - ns J10 TTDI_HLD TDI hold time from TCK rise 4 TCK fall to Data Valid from High-Z, 2-mA drive TCK fall to Data Valid from High-Z, 4-mA drive J11 TTDO_ZDV TCK fall to Data Valid from High-Z, 8-mA drive - TTDO_DV TTDO_DVZ ns ns 9 26 ns 8 26 ns 10 29 ns TCK fall to Data Valid from Data Valid, 2-mA drive 14 20 ns 10 26 ns 8 21 ns TCK fall to Data Valid from Data Valid, 8-mA drive with slew rate control 10 26 ns TCK fall to High-Z from Data Valid, 2-mA drive 7 16 ns 7 16 ns 7 16 ns 8 19 ns TCK fall to Data Valid from Data Valid, 8-mA drive - TCK fall to High-Z from Data Valid, 4-mA drive J13 35 TCK fall to Data Valid from High-Z, 8-mA drive with slew rate control TCK fall to Data Valid from Data Valid, 4-mA drive J12 13 TCK fall to High-Z from Data Valid, 8-mA drive - TCK fall to High-Z from Data Valid, 8-mA drive with slew rate control a. A ratio of at least 8:1 must be kept between the system clock and TCK. Figure 25-2. JTAG Test Clock Input Timing J2 J3 J4 TCK J6 J5 November 08, 2011 1411 Texas Instruments-Advance Information Electrical Characteristics Figure 25-3. JTAG Test Access Port (TAP) Timing TCK J7 TMS TDI J8 TMS Input Valid J9 J9 J10 TDI Input Valid TDO J8 TMS Input Valid J11 25.5 J7 J10 TDI Input Valid J12 J13 TDO Output Valid TDO Output Valid Power and Brown-Out Table 25-6. Power Characteristics Parameter No. P1 P2 Parameter Parameter Name TVDDRISE VTH Supply voltage (VDD) rise time VBTH - Nom Max Unit - ∞ ms b pending V b pending V b pending V b Power-On Reset threshold (rising edge) a pending 2.92 Power-On Reset threshold (falling edge) pending 2.35 Brown-Out Reset threshold (rising edge) P3 Min Brown-Out Reset threshold (falling edge) pending 2.92 pending 2.92 pending V P4 TPOR Power-On Reset timeout - - 500 µs P5 TBOR Brown-Out Reset timeout 1 - - c µs a. Pending characterization. b. Preliminary, pending characterization. c. After the minimum timeout, BOR stays active as long as the power supply is below VBTH. The voltage level is checked every clock cycle after the initial countdown completes. BOR is deasserted on the next clock cycle after the BOR condition goes away. 1412 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 25-4. Power-On and Brown-Out Reset and Voltage Parameters P1 VDD P2R = P3R P3F P2F P4 1 /POR 0 1 /BOR 0 Figure 25-5. Brown-Out Reset Timing P3 VDD P5 /Reset (Internal) 25.6 Reset Table 25-7. Reset Characteristics Parameter No. Parameter Parameter Name Min Nom Max Unit 20 - a - µs R1 TIRHWR Internal reset timeout after hardware reset (RST pin) R2 TIRSWR Internal reset timeout after software-initiated system reset - 1 - µs R3 TIRWDR Internal reset timeout after watchdog reset - 1 - µs R4 TIRMFR Internal reset timeout after MOSC failure reset - 1 - µs November 08, 2011 1413 Texas Instruments-Advance Information Electrical Characteristics Table 25-7. Reset Characteristics (continued) Parameter No. Parameter R5 TMIN Parameter Name Min Nom Max Unit Minimum RST pulse width 100 - - ns a. After the minimum timeout, internal reset stays active as long as the RST pin is asserted, and is released when the RST pin is deasserted. Figure 25-6. External Reset Timing (RST) RST R5 R1 /Reset (Internal) Figure 25-7. Software Reset Timing SW Reset R2 /Reset (Internal) Figure 25-8. Watchdog Reset Timing WDOG Reset (Internal) R3 /Reset (Internal) Figure 25-9. MOSC Failure Reset Timing MOSC Fail Reset (Internal) R4 /Reset (Internal) 25.7 On-Chip Low Drop-Out (LDO) Regulator Table 25-8. LDO Regulator Characteristics Parameter Parameter Name Min Nom Max Unit CLDO External filter capacitor size for internal power a supply 2.5 - 4.0 µF ESR Filter capacitor equivalent series resistance 10 - 100 mΩ 1414 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 25-8. LDO Regulator Characteristics (continued) Parameter Parameter Name Min ESL Filter capacitor equivalent series inductance VLDO LDO output voltage IINRUSH Inrush current Nom Max Unit - - 0.5 nH 1.08 1.2 1.32 V 50 - 250 mA a. The capacitor should be connected as close as possible to pin D6. 25.8 Clocks The following sections provide specifications on the various clock sources and mode. 25.8.1 PLL Specifications The following tables provide specifications for using the PLL. Table 25-9. Phase Locked Loop (PLL) Characteristics Parameter Parameter Name Min FREF_XTAL Crystal reference 5 FREF_EXT External clock referencea FPLL TREADY b Nom Max Unit a - 25 MHz 5 a - 25 MHz PLL frequency - 400 - PLL lock time, enabling the PLL - - 512 * (N+1) MHz PLL lock time, changing the XTAL field in the RCC/RCC2 register or changing the OSCSRC between MOSC and PIOSC - - 128 * (N+1) c reference clocks d c reference clocks d a. If the PLL is not used, the minimum input frequency can be 4 MHz. b. PLL frequency is automatically calculated by the hardware based on the XTAL field of the RCC register. c. N is the value in the N field in the PLLFREQ1 register. d. A reference clock is the clock period of the crystal being used, which can be MOSC or PIOSC. For example, a 16-MHz crystal connected to MOSC yields a reference clock of 62.5 ns. Table 25-10 on page 1415 shows the actual frequency of the PLL based on the crystal frequency used (defined by the XTAL field in the RCC register). Table 25-10. Actual PLL Frequency XTAL Crystal Frequency (MHz) MINT MFRAC Q N PLL Multiplier PLL Frequency (MHz) Error 0x09 5.0 0x50 0x0 0x0 0x0 80 400 - 0x0A 5.12 0x9C 0x100 0x0 0x1 156.25 400 - 0x0B 6.0 0xC8 0x0 0x0 0x2 200 400 - 0x0C 6.144 0xC3 0x140 0x0 0x2 195.3125 400 - 0x0D 7.3728 0xA2 0x30A 0x0 0x2 162.7598 399.9984 0.0004% 0x0E 8.0 0x32 0x0 0x0 0x0 50 400 - 0x0F 8.192 0xC3 0x140 0x0 0x3 195.3125 400 - 0x10 10.0 0x50 0x0 0x0 0x1 80 400 - 0x11 12.0 0xC8 0x0 0x0 0x5 200 400 - 0x12 12.288 0xC3 0x140 0x0 0x5 195.3125 400 - 0x13 13.56 0xB0 0x3F6 0x0 0x5 176.9902 399.9979 0.0005% November 08, 2011 1415 Texas Instruments-Advance Information Electrical Characteristics Table 25-10. Actual PLL Frequency (continued) 25.8.2 XTAL Crystal Frequency (MHz) MINT MFRAC Q N PLL Multiplier PLL Frequency (MHz) Error 0x14 14.318 0xC3 0x238 0x0 0x6 195.5547 399.9982 0.0005% 0x15 16.0 0x32 0x0 0x0 0x1 50 400 - 0x16 16.384 0xC3 0x140 0x0 0x7 195.3125 400 - 0x17 18 0xC8 0x0 0x0 0x8 200 400 - 0x18 20 0x50 0x0 0x0 0x3 80 400 - 0x19 24 0x32 0x0 0x0 0x2 50 400 - 0x1A 25 0x50 0x0 0x0 0x4 80 400 - PIOSC Specifications Table 25-11. PIOSC Clock Characteristics Parameter Min Nom FPIOSC25 Parameter Name Internal 16-MHz precision oscillator frequency variance, factory calibrated at 25 °C - ±0.25% ±1% Max FPIOSCT Internal 16-MHz precision oscillator frequency variance, factory calibrated at 25 °C, across specified temperature range - - ±3% FPIOSCUCAL Internal 16-MHz precision oscillator frequency variance, user calibrated at a chosen temperature - ±0.25% a a Unit a - a - a - ±1% a. Preliminary, pending characterization. 25.8.3 Internal 30-kHz Oscillator Specifications Table 25-12. 30-kHz Clock Characteristics Parameter FIOSC30KHZ Parameter Name Min Nom a Internal 30-KHz oscillator frequency 10 30 Max Unit a KHz 50 a. Preliminary, pending characterization. 25.8.4 Hibernation Clock Source Specifications Table 25-13. HIB Oscillator Input Characteristics Parameter FHIBOSC C1, C2 CPKG CPCB C0 CSHUNT Parameter Name Parallel resonance frequency a External load capacitance on XOSC0, XOSC1 pins a Device package stray shunt capacitance a PCB stray shunt capacitance a Crystal shunt capacitance a Total shunt capacitance DL TSTART Nom Max Unit - 32.768 - KHz 12 - 24 pF - 0.5 - pF - 0.5 - pF - 3 - pF - - 4 pF b - - 50 kΩ Crystal effective series resistance, OSCDRV = 1 b - - 75 kΩ Oscillator output drive level - - 0.25 Crystal effective series resistance, OSCDRV = 0 ESR Min c Oscillator startup time, when using a crystal - 1416 600 µW d pending ms November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 25-13. HIB Oscillator Input Characteristics (continued) Parameter Parameter Name Min Nom Max Unit VIH CMOS input high level, when using an external e oscillator Supply 0.4 - Supply V VIL CMOS input low level, when using an external oscillator GND - GND + 0.4 V VHYS CMOS input buffer hysteresis, when using an external oscillator - 600 - mV 45 - 55 % DCHIBOSC_EXT External clock reference duty cycle a. See information below table. b. Crystal ESR specified by crystal manufacturer. c. Oscillator startup time is specified from the time the oscillator is enabled to when it reaches a stable point of oscillation such that the internal clock is valid. d. Pending characterization. e. Maximum VIH is relative to the larger of VDD or VBAT. The load capacitors added on the board, C1 and C2, should be chosen such that the following equation is satisfied (see Table 25-13 on page 1416 for typical values). ■ CL = load capacitance specified by crystal manufacturer ■ CL = (C1*C2)/(C1+C2) + CPKG + CPCB ■ CSHUNT = CPKG + CPCB + C0 (total shunt capacitance seen across XOSC0, XOSC1) ■ CPKG, CPCB as measured across the XOSC0, XOSC1 pins excluding the crystal ■ Clear the OSCDRV bit in the Hibernation Control (HIBCTL) register for C1,2 ≤ 18 pF; set the OSCDRV bit for C1,2 > 18 pF. ■ C0 = Shunt capacitance of crystal specified by the crystal manufacturer 25.8.5 Main Oscillator Specifications Table 25-14. Main Oscillator Input Characteristics Parameter FMOSC Parameter Name Min Nom Max Unit - 25 MHz 12 - 24 pF - 0.5 - pF - 0.5 - pF - 4 - pF - - 4 pF dc - - 300 Ω dc - - 200 Ω dc a Parallel resonance frequency 4 b C1, C2 External load capacitance on OSC0, OSC1 pins CPKG Device package stray shunt capacitance CPCB C0 CSHUNT b b PCB stray shunt capacitance bc Crystal shunt capacitance b Total shunt capacitance Crystal effective series resistance, 4 MHz Crystal effective series resistance, 6 MHz Crystal effective series resistance, 8 MHz ESR - - 130 Ω dc - - 120 Ω dc - - 100 Ω dc - - 50 Ω - - OSCPWR mW Crystal effective series resistance, 12 MHz Crystal effective series resistance, 16 MHz Crystal effective series resistance, 25 MHz DL e Oscillator output drive level November 08, 2011 1417 Texas Instruments-Advance Information Electrical Characteristics Table 25-14. Main Oscillator Input Characteristics (continued) Parameter TSTART Parameter Name Min f Oscillator startup time, when using a crystal Nom Max Unit - - 18 ms 0.65 * VDD - VDD V CMOS input low level, when using an external oscillator GND - 0.35 * VDD V CMOS input buffer hysteresis, when using an external oscillator 150 - - mV 45 - 55 % VIH CMOS input high level, when using an external oscillator VIL VHYS DCHIBOSC_EXT External clock reference duty cycle a. 5 MHz is the minimum when using the PLL. b. See information below table. c. Crystal vendors can be contacted to confirm these specifications are met for a specific crystal part number if the vendors generic crystal datasheet show limits outside of these specifications. d. Crystal ESR specified by crystal manufacturer. e. OSCPWR = (2 * pi * FP * CL * 2.5)2 * ESR / 2. MOSC is capable of supplying over 1 mW of power. The maximum power delivered to the crystal is based on the CL, FP and ESR parameters of the crystal in the circuit as calculated by the OSCPWR equation. Ensure that the value calculated for OSCPWR does not exceed the crystal's drive-level maximum. f. Oscillator startup time is specified from the time the oscillator is enabled to when it reaches a stable point of oscillation such that the internal clock is valid. The load capacitors added on the board, C1 and C2, should be chosen such that the following equation is satisfied (see Table 25-14 on page 1417 for typical values). ■ CL = load capacitance specified by crystal manufacturer ■ CL = (C1*C2)/(C1+C2) + CSHUNT ■ CSHUNT = C0 + CPKG + CPCB (total shunt capacitance seen across OSC0, OSC1 crystal inputs) ■ CPKG, CPCB = the mutual caps as measured across the OSC0,OSC1 pins excluding the crystal. ■ C0 = Shunt capacitance of crystal specified by the crystal manufacturer a Table 25-15. Supported MOSC Crystal Frequencies Value Crystal Frequency (MHz) Not Using the PLL 0x00-0x5 Crystal Frequency (MHz) Using the PLL reserved 0x06 4 MHz reserved 0x07 4.096 MHz reserved 0x08 4.9152 MHz reserved 0x09 5 MHz (USB) 0x0A 5.12 MHz 0x0B 6 MHz (USB) 0x0C 6.144 MHz 0x0D 7.3728 MHz 0x0E 8 MHz (USB) 0x0F 8.192 MHz 0x10 10.0 MHz (USB) 0x11 12.0 MHz (USB) 0x12 12.288 MHz 1418 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 25-15. Supported MOSC Crystal Frequencies (continued) Value Crystal Frequency (MHz) Not Using the PLL Crystal Frequency (MHz) Using the PLL 0x13 13.56 MHz 0x14 14.31818 MHz 0x15 16.0 MHz (reset value)(USB) 0x16 16.384 MHz 0x17 18.0 MHz (USB) 0x18 20.0 MHz (USB) 0x19 24.0 MHz (USB) 0x1A 25.0 MHz (USB) a. Frequencies that may be used with the USB interface are indicated in the table. 25.8.6 System Clock Specification with ADC Operation Table 25-16. System Clock Characteristics with ADC Operation Parameter Fsysadc Parameter Name System clock frequency when the ADC a module is operating (when PLL is bypassed). Min Nom Max Unit 15.9952 16 16.0048 MHz a. Clock frequency (plus jitter) must be stable inside specified range. ADC can be clocked from the PLL, directly from an external clock source, or from the PIOSC, as long as frequency absolute precision is inside specified range. 25.8.7 System Clock Specification with USB Operation Table 25-17. System Clock Characteristics with USB Operation Parameter Fsysusb 25.9 Parameter Name Min Nom Max Unit 30 - - MHz Min Nom Max Unit Time to wake from interrupt in sleep mode - - 2 system clocks Time to wake from interrupt in deep-sleep mode, using PIOSC for both Run mode and Deep-sleep bc mode - 1.25 - µs Time to wake from interrupt in deep-sleep mode, using PIOSC for Run mode and IOSC for Deep-sleep cb mode mode - 350 - µs - - TREADY ms System clock frequency when the USB module is operating (note that MOSC must be the clock source, either with or without using the PLL) Sleep Modes a Table 25-18. Sleep Modes AC Characteristics Parameter No Parameter TWAKE_S D1 TWAKE_DS D2 Parameter Name b TWAKE_PLL_DS Time to wake from interrupt in deep-sleep mode b when using the PLL a. Values in this table assume the IOSC is the clock source during sleep or deep-sleep mode. b. Specified from registering the interrupt to first instruction. c. If the main oscillator is used for run mode, add the main oscillator startup time, TSTART. November 08, 2011 1419 Texas Instruments-Advance Information Electrical Characteristics 25.10 Hibernation Module The Hibernation module requires special system implementation considerations because it is intended to power down all other sections of its host device, refer to “Hibernation Module” on page 522. Table 25-19. Hibernation Module Battery Characteristics Parameter Parameter Name VBAT VLOWBAT Min Nominal Max Unit Battery supply voltage 1.8 3.0 3.6 V Low battery detect voltage, VBATSEL=0x0 1.85 1.9 1.95 V Low battery detect voltage, VBATSEL=0x1 2.05 2.1 2.15 V Low battery detect voltage, VBATSEL=0x2 2.25 2.3 2.35 V Low battery detect voltage, VBATSEL=0x3 2.45 2.5 2.55 V Table 25-20. Hibernation Module AC Characteristics Parameter No Parameter Parameter Name Min Nom Max Unit H1 TWAKE 100 - - ns H2 TWAKE_TO_HIB WAKE assert to HIB desassert (wake up time) - - 31 μs H3 TVDD_RAMP VDD ramp to 3.0 V - Depends on characteristics of power supply - μs H4 TVDD_CODE VDD at 3.0 V to internal POR deassert; first instruction executes - - 500 μs WAKE assertion time Figure 25-10. Hibernation Module Timing H1 WAKE H2 HIB H3 VDD H4 POR 1420 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 25.11 Flash Memory and EEPROM Table 25-21. Flash Memory Characteristics Parameter PECYC TRET TPROG64 TERASE TME Parameter Name Number of guaranteed program/erase cycles before a failure Data retention, -40˚C to +85˚C Min Nom Max Unit 100,000 - - cycles 10 - - years c Program time for double-word-aligned 64 bits of b data 30 50 150 µs Page erase time, 1. b. If programming fewer than 64 bits of data, the programming time is the same. For example, if only 32 bits of data need to be programmed, the other 32 bits are masked off. c. The memory controller will complete the operation within this specified maximum. It is possible under extreme conditions on previous endurance cycling that a verification failure flag will be issued upon completion. In the event that this flag is generated, issue the same operation again to extend the high-voltage operation. a Table 25-22. EEPROM Characteristics Parameter Parameter Name EPECYC ETRET ETPROG ETREAD ETME Min Nom Max Unit Number of guaranteed mass program/erase cycles of a single 500,000 b word before failure - - cycles Data retention, -40˚C to +85˚C 10 - - years Program time for 32 bits of data - space available - 110 600 μs Program time for 32 bits of data - requires a copy to the copy buffer, copy buffer has space and less than 10% of EEPROM endurance used - 30 - ms Program time for 32 bits of data - requires a copy to the copy buffer, copy buffer has space and greater than 90% of EEPROM endurance used - - 900 ms Program time for 32 bits of data - requires a copy to the copy buffer, copy buffer requires an erase and less than 10% of EEPROM endurance used - 60 - ms Program time for 32 bits of data - requires a copy to the copy buffer, copy buffer requires an erase and greater than 90% of EEPROM endurance used - - 1800 ms Read access time - 4 - system clocks Mass erase time, 0 -> 1. 25.12 GPIO Module Note: All GPIOs are 5-V tolerant, except PB0 and PB1. See “Signal Description” on page 675 for more information on GPIO configuration. November 08, 2011 1421 Texas Instruments-Advance Information Electrical Characteristics Table 25-23. GPIO Module Characteristics Parameter Parameter Name Min Nom Max Unit RGPIOPU GPIO internal pull-up resistor 13 20 30 kΩ RGPIOPD GPIO internal pull-down resistor 13 20 35 kΩ - - 1.0 µA a ILKG GPIO input leakage current, VIN = 3.3 V ± 10% a GPIO input leakage current, VIN = 5.0 VIN ± 10% - - TGPIOR c µA 14 pending d ns b c pending ns GPIO Rise Time, 4-mA drive 6 - b GPIO Rise Time, 8-mA drive c pending ns c pending ns 4 b GPIO Rise Time, 8-mA drive with slew rate control 5 e 20 c pending ns e c pending ns GPIO Fall Time, 2-mA drive TGPIOF 60 b GPIO Rise Time, 2-mA drive GPIO Fall Time, 4-mA drive 9 - e GPIO Fall Time, 8-mA drive c pending ns c pending ns 4 e GPIO Fall Time, 8-mA drive with slew rate control 6 a. The leakage current is measured with GND or VDD applied to the corresponding pin(s). The leakage of digital port pins is measured individually. The port pin is configured as an input and the pullup/pulldown resistor is disabled. b. Time measured from 20% to 80% of VDD. c. Preliminary, pending characterization. d. Pending characterization. e. Time measured from 80% to 20% of VDD. 25.13 Analog-to-Digital Converter (ADC) a Table 25-24. ADC Electrical Characteristics Parameter Parameter Name Min Nom Max Unit POWER SUPPLY REQUIREMENTS VDDA ADC supply voltage 2.9 3.3 3.6 V GNDA ADC ground voltage - 0 - V - 1.0 // 0.01 - μF VDDA / GNDA VOLTAGE REFERENCE CREF Voltage reference decoupling capacitance b EXTERNAL VOLTAGE REFERENCE INPUT VREF+ Positive external voltage reference for ADC, when VREF field in the ADCCTL register is not c 0x0 - 2.4 VDDA VDDA V VREF- Negative external voltage reference for ADC, when VREF field in the ADCCTL register is not c 0x0 GNDA GNDA 0.3 V IVREF Current on VREF+ input, using external VREF+ = 3.3 V - 330.5 440 µA ILVREF DC leakage current on VREF+ input when external VREF disabled - - 2.0 µA CREF External reference decoupling capacitance - 1.0 // 0.01 - μF c d ANALOG INPUT 1422 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 25-24. ADC Electrical Characteristics (continued) Parameter Parameter Name Min Nom Max Unit 0 - VDDA V Differential, full-scale analog input voltage, eg internal reference -VDDA - VVDDA V Single-ended, full-scale analog input voltage, cf external reference VREFA- - VREFA+ V - (VREFA+ VREFA-) - VREFA+ VREFA- V - - 2.0 µA - - 2.5 kΩ - - 10 pF - - 500 Ω - 16 - MHz - 250 Single-ended, full- scale analog input voltage, ef internal reference VADCIN Differential, full-scale analog input voltage, ch external reference IL i ADC input leakage current i RADC ADC equivalent input resistance CADC ADC equivalent input capacitance RS i i Analog source resistance SAMPLING DYNAMICS j FADC ADC conversion clock frequency FCONV ADC conversion rate TS ADC sample time TC ADC conversion time TLT Latency from trigger to start of conversion 1 MSPS - ns 1 - µs 2 - ADC clocks kl SYSTEM PERFORMANCE N Resolution 12 bits m INL Integral nonlinearity error, over full input range - ±1.5 DNL Differential nonlinearity error, over full input range - ±0.8 ±1.0 LSB EO Offset error - ±1.0 pending LSB EG n - ±2.0 pending LSB - ±3.5 pending LSB ET Gain error o Total unadjusted error, over full input range pending LSB TEMPERATURE SENSOR VTSENS Temperature sensor voltage, junction temperature 25 °C - 1.633 - V STSENS Temperature sensor slope, ambient temperature --40 °C to 85 °C - -13.3 - mV/°C ETSENS Temperature sensor accuracy, ambient p temperature --40 °C to 85 °C - - ±5 °C a. At ambient temperature= -40 °C to 85 °C, VREF= 3.3V, FADC=16 MHz unless otherwise noted. b. Two capacitors in parallel. c. Assumes external filtering network between VREF+ and VREF- as shown in Figure 25-11 on page 1424. External reference noise level must be under 12bit (-74 dB) of Full Scale input, over input bandwidth, measured at VREF+ - VREF-. d. Two capacitors in parallel. e. Internal reference is connected directly between VDDA and GNDA (VREFi = VDDA - GNDA). Dynamic characteristics can not be ensured when internal reference is used due to potential high noise coupling through VDDA. Use only when data can be averaged over many samples. Internal reference voltage is selected when VREF field in the ADCCTL register is 0x0. f. VADCIN = VINP - VINN g. With signal common mode as VDDA/2. h. With signal common mode as (VREF+ + VREF-)/2. November 08, 2011 1423 Texas Instruments-Advance Information Electrical Characteristics i. As shown in Figure 25-12 on page 1425, RADC is the total equivalent resistance in the input line all the way up to the sampling node at the input of the ADC. j. See “System Clock Specification with ADC Operation” on page 1419 for full ADC clock frequency specification. k. Low noise environment is assumed in order to obtain values close to spec. Board must have good ground isolation between analog and digital grounds, a clean reference voltage is assumed, and input signal must be bandlimited to Nyquist bandwidth. No anti-aliasing filter is provided internally. l. ADC static measurements taken by averaging over several samples. At least 20-sample averaging is assumed to obtain expected typical or maximum spec values. m. Pending characterization. n. Gain error is measured at max code after compensating for offset. Gain error is equivalent to "Full Scale Error." It can be given in % of slope error, or in LSB, as done here. o. Total Unadjusted Error is the maximum error at any one code versus the ideal ADC curve. It includes all other errors (offset error, gain error and INL) at any given ADC code. p. Note that this parameter does not include ADC error. Figure 25-11. ADC External Reference Filtering Stellaris® Microcontroller IVREF VREF+ VREF+ CREF VREF‐ VREF VREF‐ 1424 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 25-12. ADC Input Equivalency Diagram VDD Zs ESD  Clamp Rs VS Input PAD  Equivalent  Circuit Stellaris® Microcontroller ZADC RADC Pin VADCIN Cs ESD  Clamp 12‐bit SAR ADC Converter 12‐bit Word ILK G Pin Input PAD  Equivalent  Circuit Pin Input PAD  Equivalent  Circuit RADC RADC CADC 25.14 Synchronous Serial Interface (SSI) Table 25-25. SSI Characteristics Parameter No. Parameter Parameter Name Min Nom Max Unit S1 TCLK_PER SSIClk cycle time 40 - - ns S2 S3 TCLK_HIGH SSIClk high time - 0.5 - t clk_per TCLK_LOW SSIClk low time - 0.5 - S4 TCLKRF a b SSIClk rise/fall time - t clk_per c 4 pending ns S5 TDMD Data from master valid delay time 0 - 1 system clocks S6 TDMS Data from master setup time 1 - - system clocks S7 TDMH Data from master hold time 2 - - system clocks S8 TDSS Data from slave setup time 1 - - system clocks S9 TDSH Data from slave hold time 2 - - system clocks a. In master mode, the system clock must be at least twice as fast as the SSIClk; in slave mode, the system clock must be at least 6 times faster than the SSIClk. b. Note that the delays shown are using 8-mA drive strength. c. Pending characterization. November 08, 2011 1425 Texas Instruments-Advance Information Electrical Characteristics Figure 25-13. SSI Timing for TI Frame Format (FRF=01), Single Transfer Timing Measurement S1 S4 S2 SSIClk S3 SSIFss SSITx SSIRx MSB LSB 4 to 16 bits Figure 25-14. SSI Timing for MICROWIRE Frame Format (FRF=10), Single Transfer S2 S1 SSIClk S3 SSIFss SSITx MSB LSB 8-bit control SSIRx 0 MSB LSB 4 to 16 bits output data 1426 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure 25-15. SSI Timing for SPI Frame Format (FRF=00), with SPH=1 S1 S4 S2 SSIClk (SPO=1) S3 SSIClk (SPO=0) S6 SSITx (master) S7 MSB S5 SSIRx (slave) S8 LSB S9 MSB LSB SSIFss 25.15 Inter-Integrated Circuit (I2C) Interface Table 25-26. I2C Characteristics Parameter No. Parameter Parameter Name Min Nom Max Unit a TSCH Start condition hold time 36 - - system clocks a TLP Clock Low period 36 - - system clocks b TSRT I2CSCL/I2CSDA rise time (VIL =0.5 V to V IH =2.4 V) - - (see note b) ns a TDH Data hold time 2 - - system clocks c TSFT I2CSCL/I2CSDA fall time (VIH =2.4 V to V IL =0.5 V) - 9 10 ns a THT Clock High time 24 - - system clocks a TDS Data setup time 18 - - system clocks a TSCSR Start condition setup time (for repeated start condition only) 36 - - system clocks a TSCS Stop condition setup time 24 - - system clocks I1 I2 I3 I4 I5 I6 I7 I8 I9 a. Values depend on the value programmed into the TPR bit in the I2C Master Timer Period (I2CMTPR) register; a TPR programmed for the maximum I2CSCL frequency (TPR=0x2) results in a minimum output timing as shown in the table above. The I 2C interface is designed to scale the actual data transition time to move it to the middle of the I2CSCL Low period. The actual position is affected by the value programmed into the TPR; however, the numbers given in the above values are minimum values. b. Because I2CSCL and I2CSDA are open-drain-type outputs, which the controller can only actively drive Low, the time I2CSCL or I2CSDA takes to reach a high level depends on external signal capacitance and pull-up resistor values. c. Specified at a nominal 50 pF load. November 08, 2011 1427 Texas Instruments-Advance Information Electrical Characteristics Figure 25-16. I2C Timing I2 I6 I5 I2CSCL I1 I4 I7 I8 I3 I9 I2CSDA 25.16 Universal Serial Bus (USB) Controller ® The Stellaris USB controller electrical specifications are compliant with the Universal Serial Bus Specification Rev. 2.0 (full-speed and low-speed support) and the On-The-Go Supplement to the USB 2.0 Specification Rev. 1.0. Some components of the USB system are integrated within the LM4F232H5BB microcontroller and specific to the Stellaris microcontroller design. 25.17 Analog Comparator Table 25-27. Analog Comparator Characteristics Parameter VINP,VINN VCM VOS Min Nom Max Unit Input voltage range Parameter Name GNDA - VDDA V Input common mode voltage range GNDA - VDDA Input offset voltage - Input leakage current over full voltage range Common mode rejection ratio TRT TMC IINP,IINN CMRR V a ±10 pending mV - - 2.0 µA - 50 - dB Response time - - 1 µs Comparator mode change to Output Valid - - 10 µs a. Pending characterization. Table 25-28. Analog Comparator Voltage Reference Characteristics Parameter Min Nom Max Unit RHR Parameter Name Resolution high range - VDDA/29.23 - V RLR Resolution low range - VDDA/22.11 - V AHR Absolute accuracy high range, LSB = VDDA/29.23 - - ±1/2 LSB ALR Absolute accuracy low range, LSB = VDDA/22.11 - - ±1/4 LSB 25.18 Current Consumption 25.18.1 Preliminary Current Consumption The following table provides preliminary figures for current consumption while ongoing characterization is completed. 1428 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Table 25-29. Preliminary Current Consumption Parameter Parameter Name Conditions Nom Max Unit Run mode 1 (Flash loop) VDD = 3.3 V 50 - mA 40 - mA 30 - mA 20 - mA 12 - mA 4.5 - mA 3.8 - mA VDDA = 3.3 V a Test Configuration: Typical system configuration Peripherals = All ON System Clock = 80 MHz (with PLL) Temp = 25°C Run mode 1 (SRAM loop) VDD = 3.3 V VDDA = 3.3 V a Test Configuration: Typical system configuration Peripherals = All ON System Clock = 80 MHz (with PLL) IDD_RUN Temp = 25°C Run mode 2 (Flash loop) VDD = 3.3 V VDDA = 3.3 V a Test Configuration: Typical system configuration Peripherals = All OFF System Clock = 80 MHz (with PLL) Temp = 25°C Run mode 2 (SRAM loop) VDD = 3.3 V VDDA = 3.3 V a Test Configuration: Typical system configuration Peripherals = All OFF System Clock = 80 MHz (with PLL) Temp = 25°C VDD = 3.3 V VDDA = 3.3 V a Test Configuration: Typical system configuration Peripherals = All OFF System Clock = 80 MHz (with PLL) Temp = 25°C VDD = 3.3 V VDDA = 3.3 V a IDD_SLEEP Sleep mode Test Configuration: Typical system configuration Peripherals = All OFF b System Clock =16 MHz (with PIOSC) Temp = 25°C VDD = 3.3 V VDDA = 3.3 V a Test Configuration: Typical system configuration Peripherals = All OFF b System Clock =1 MHz (with PIOSC/16) Temp = 25°C November 08, 2011 1429 Texas Instruments-Advance Information Electrical Characteristics Table 25-29. Preliminary Current Consumption (continued) Parameter Parameter Name IDD_DEEPSLEEP Deep-sleep mode Conditions Nom Max Unit pending - µA 1.6 - µA 1.7 - µA 5.0 - µA c VDD = 3.3 V VDDA = 3.3 V a Test Configuration: Typical system configuration Peripherals = All OFF System Clock = IOSC30KHZ Temp = 25°C IHIB_NORTC Hibernate mode (external wake, RTC disabled) VBAT = 3.0 V VDD = 0 V VDDA = 0 V a Test Configuration: Typical system configuration System Clock = OFF Hibernate Module = 32.768 kHz IHIB_RTC Hibernate mode (RTC VBAT = 3.0 V enabled) VDD = 0 V VDDA = 0 V a Test Configuration: Typical system configuration System Clock = OFF Hibernate Module = 32.768 kHz IHIB_VDD3ON Hibernate mode (VDD3ON mode) VBAT = 3.0 V VDD = 3.3 V VDDA = 3.3 V a Test Configuration: Typical system configuration System Clock = OFF Hibernate Module = 32.768 kHz a. Will be updated with specific details upon further characterization. b. Note that if the MOSC is the source of the Run-mode system clock and is powered down in Sleep mode, wake time is increased by TMOSC_SETTLE. c. Pending characterization. 1430 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller A Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 The Cortex-M4F Processor R0, type R/W, , reset - (see page 77) DATA DATA R1, type R/W, , reset - (see page 77) DATA DATA R2, type R/W, , reset - (see page 77) DATA DATA R3, type R/W, , reset - (see page 77) DATA DATA R4, type R/W, , reset - (see page 77) DATA DATA R5, type R/W, , reset - (see page 77) DATA DATA R6, type R/W, , reset - (see page 77) DATA DATA R7, type R/W, , reset - (see page 77) DATA DATA R8, type R/W, , reset - (see page 77) DATA DATA R9, type R/W, , reset - (see page 77) DATA DATA R10, type R/W, , reset - (see page 77) DATA DATA R11, type R/W, , reset - (see page 77) DATA DATA R12, type R/W, , reset - (see page 77) DATA DATA SP, type R/W, , reset - (see page 78) SP SP LR, type R/W, , reset 0xFFFF.FFFF (see page 79) LINK LINK PC, type R/W, , reset - (see page 80) PC PC November 08, 2011 1431 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PSR, type R/W, , reset 0x0100.0000 (see page 81) N Z C V Q ICI / IT THUMB GE ICI / IT ISRNUM PRIMASK, type R/W, , reset 0x0000.0000 (see page 85) PRIMASK FAULTMASK, type R/W, , reset 0x0000.0000 (see page 86) FAULTMASK BASEPRI, type R/W, , reset 0x0000.0000 (see page 87) BASEPRI CONTROL, type R/W, , reset 0x0000.0000 (see page 88) FPCA ASP TMPL OFC DZC IOC CLK_SRC INTEN ENABLE FPSC, type R/W, , reset - (see page 90) N Z C V AHP DN FZ RMODE IDC IXC UFC Cortex-M4 Peripherals System Timer (SysTick) Registers Base 0xE000.E000 STCTRL, type R/W, offset 0x010, reset 0x0000.0004 COUNT STRELOAD, type R/W, offset 0x014, reset RELOAD RELOAD STCURRENT, type R/WC, offset 0x018, reset CURRENT CURRENT Cortex-M4 Peripherals Nested Vectored Interrupt Controller (NVIC) Registers Base 0xE000.E000 EN0, type R/W, offset 0x100, reset 0x0000.0000 INT INT EN1, type R/W, offset 0x104, reset 0x0000.0000 INT INT EN2, type R/W, offset 0x108, reset 0x0000.0000 INT INT EN3, type R/W, offset 0x10C, reset 0x0000.0000 INT INT EN4, type R/W, offset 0x110, reset 0x0000.0000 INT DIS0, type R/W, offset 0x180, reset 0x0000.0000 INT INT 1432 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DIS1, type R/W, offset 0x184, reset 0x0000.0000 INT INT DIS2, type R/W, offset 0x188, reset 0x0000.0000 INT INT DIS3, type R/W, offset 0x18C, reset 0x0000.0000 INT INT DIS4, type R/W, offset 0x190, reset 0x0000.0000 INT PEND0, type R/W, offset 0x200, reset 0x0000.0000 INT INT PEND1, type R/W, offset 0x204, reset 0x0000.0000 INT INT PEND2, type R/W, offset 0x208, reset 0x0000.0000 INT INT PEND3, type R/W, offset 0x20C, reset 0x0000.0000 INT INT PEND4, type R/W, offset 0x210, reset 0x0000.0000 INT UNPEND0, type R/W, offset 0x280, reset 0x0000.0000 INT INT UNPEND1, type R/W, offset 0x284, reset 0x0000.0000 INT INT UNPEND2, type R/W, offset 0x288, reset 0x0000.0000 INT INT UNPEND3, type R/W, offset 0x28C, reset 0x0000.0000 INT INT UNPEND4, type R/W, offset 0x290, reset 0x0000.0000 INT ACTIVE0, type RO, offset 0x300, reset 0x0000.0000 INT INT ACTIVE1, type RO, offset 0x304, reset 0x0000.0000 INT INT ACTIVE2, type RO, offset 0x308, reset 0x0000.0000 INT INT November 08, 2011 1433 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ACTIVE3, type RO, offset 0x30C, reset 0x0000.0000 INT INT ACTIVE4, type RO, offset 0x310, reset 0x0000.0000 INT PRI0, type R/W, offset 0x400, reset 0x0000.0000 INTD INTC INTB INTA PRI1, type R/W, offset 0x404, reset 0x0000.0000 INTD INTC INTB INTA PRI2, type R/W, offset 0x408, reset 0x0000.0000 INTD INTC INTB INTA PRI3, type R/W, offset 0x40C, reset 0x0000.0000 INTD INTC INTB INTA PRI4, type R/W, offset 0x410, reset 0x0000.0000 INTD INTC INTB INTA PRI5, type R/W, offset 0x414, reset 0x0000.0000 INTD INTC INTB INTA PRI6, type R/W, offset 0x418, reset 0x0000.0000 INTD INTC INTB INTA PRI7, type R/W, offset 0x41C, reset 0x0000.0000 INTD INTC INTB INTA PRI8, type R/W, offset 0x420, reset 0x0000.0000 INTD INTC INTB INTA PRI9, type R/W, offset 0x424, reset 0x0000.0000 INTD INTC INTB INTA PRI10, type R/W, offset 0x428, reset 0x0000.0000 INTD INTC INTB INTA PRI11, type R/W, offset 0x42C, reset 0x0000.0000 INTD INTC INTB INTA PRI12, type R/W, offset 0x430, reset 0x0000.0000 INTD INTC INTB INTA PRI13, type R/W, offset 0x434, reset 0x0000.0000 INTD INTC INTB INTA PRI14, type R/W, offset 0x438, reset 0x0000.0000 INTD INTC INTB INTA 1434 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PRI15, type R/W, offset 0x43C, reset 0x0000.0000 INTD INTC INTB INTA PRI16, type R/W, offset 0x440, reset 0x0000.0000 INTD INTC INTB INTA PRI17, type R/W, offset 0x444, reset 0x0000.0000 INTD INTC INTB INTA PRI18, type R/W, offset 0x448, reset 0x0000.0000 INTD INTC INTB INTA PRI19, type R/W, offset 0x44C, reset 0x0000.0000 INTD INTC INTB INTA PRI20, type R/W, offset 0x450, reset 0x0000.0000 INTD INTC INTB INTA PRI21, type R/W, offset 0x454, reset 0x0000.0000 INTD INTC INTB INTA PRI22, type R/W, offset 0x458, reset 0x0000.0000 INTD INTC INTB INTA PRI23, type R/W, offset 0x45C, reset 0x0000.0000 INTD INTC INTB INTA PRI24, type R/W, offset 0x460, reset 0x0000.0000 INTD INTC INTB INTA PRI25, type R/W, offset 0x464, reset 0x0000.0000 INTD INTC INTB INTA PRI26, type R/W, offset 0x468, reset 0x0000.0000 INTD INTC INTB INTA PRI27, type R/W, offset 0x46C, reset 0x0000.0000 INTD INTC INTB INTA PRI28, type R/W, offset 0x470, reset 0x0000.0000 INTD INTC INTB INTA PRI29, type R/W, offset 0x474, reset 0x0000.0000 INTD INTC INTB INTA PRI30, type R/W, offset 0x478, reset 0x0000.0000 INTD INTC INTB INTA PRI31, type R/W, offset 0x47C, reset 0x0000.0000 INTD INTC INTB INTA November 08, 2011 1435 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PRI32, type R/W, offset 0x480, reset 0x0000.0000 INTD INTC INTB INTA SWTRIG, type WO, offset 0xF00, reset 0x0000.0000 INTID Cortex-M4 Peripherals System Control Block (SCB) Registers Base 0xE000.E000 ACTLR, type R/W, offset 0x008, reset 0x0000.0000 DISOOFP DISFPCA DISFOLD DISWBUF DISMCYC CPUID, type RO, offset 0xD00, reset 0x410F.C241 IMP VAR CON PARTNO REV INTCTRL, type R/W, offset 0xD04, reset 0x0000.0000 NMISET PENDSV UNPENDSV PENDSTSET PENDSTCLR VECPEND ISRPRE ISRPEND VECPEND RETBASE VECACT VTABLE, type R/W, offset 0xD08, reset 0x0000.0000 BASE OFFSET OFFSET APINT, type R/W, offset 0xD0C, reset 0xFA05.0000 VECTKEY PRIGROUP ENDIANESS SYSRESREQ VECTCLRACT VECTRESET SYSCTRL, type R/W, offset 0xD10, reset 0x0000.0000 SEVONPEND SLEEPDEEP SLEEPEXIT CFGCTRL, type R/W, offset 0xD14, reset 0x0000.0200 DIV0 STKALIGN BFHFNMIGN UNALIGNED MAINPEND BASETHR SYSPRI1, type R/W, offset 0xD18, reset 0x0000.0000 USAGE BUS MEM SYSPRI2, type R/W, offset 0xD1C, reset 0x0000.0000 SVC SYSPRI3, type R/W, offset 0xD20, reset 0x0000.0000 TICK PENDSV DEBUG SYSHNDCTRL, type R/W, offset 0xD24, reset 0x0000.0000 USAGE SVC BUSP MEMP USAGEP TICK PNDSV MON SVCA USGA BUS MEM BUSA MEMA INVSTAT UNDEF DERR IERR FAULTSTAT, type R/W1C, offset 0xD28, reset 0x0000.0000 BFARV BLSPERR BSTKE BUSTKE IMPRE DIV0 UNALIGN PRECISE IBUS NOCP MMARV MLSPERR MSTKE MUSTKE INVPC HFAULTSTAT, type R/W1C, offset 0xD2C, reset 0x0000.0000 DBG FORCED VECT MMADDR, type R/W, offset 0xD34, reset ADDR ADDR 1436 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 FAULTADDR, type R/W, offset 0xD38, reset ADDR ADDR Cortex-M4 Peripherals Memory Protection Unit (MPU) Registers Base 0xE000.E000 MPUTYPE, type RO, offset 0xD90, reset 0x0000.0800 IREGION DREGION SEPARATE MPUCTRL, type R/W, offset 0xD94, reset 0x0000.0000 PRIVDEFEN HFNMIENA ENABLE MPUNUMBER, type R/W, offset 0xD98, reset 0x0000.0000 NUMBER MPUBASE, type R/W, offset 0xD9C, reset 0x0000.0000 ADDR ADDR VALID REGION VALID REGION VALID REGION VALID REGION MPUBASE1, type R/W, offset 0xDA4, reset 0x0000.0000 ADDR ADDR MPUBASE2, type R/W, offset 0xDAC, reset 0x0000.0000 ADDR ADDR MPUBASE3, type R/W, offset 0xDB4, reset 0x0000.0000 ADDR ADDR MPUATTR, type R/W, offset 0xDA0, reset 0x0000.0000 XN AP TEX SRD S C SIZE B ENABLE MPUATTR1, type R/W, offset 0xDA8, reset 0x0000.0000 XN AP TEX SRD S C SIZE B ENABLE MPUATTR2, type R/W, offset 0xDB0, reset 0x0000.0000 XN AP TEX SRD S C SIZE B ENABLE MPUATTR3, type R/W, offset 0xDB8, reset 0x0000.0000 XN AP TEX SRD S C SIZE B ENABLE Cortex-M4 Peripherals Floating-Point Unit (FPU) Registers Base 0xE000.E000 CPAC, type R/W, offset 0xD88, reset 0x0000.0000 CP11 CP10 FPCC, type R/W, offset 0xF34, reset 0xC000.0000 ASPEN LSPEN MONRDY BFRDY MMRDY HFRDY THREAD USER LSPACT FPCA, type R/W, offset 0xF38, reset ADDRESS ADDRESS November 08, 2011 1437 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 AHP DN FZ FPDSC, type R/W, offset 0xF3C, reset 0x0000.0000 RMODE System Control Base 0x400F.E000 DID0, type RO, offset 0x000, reset - (see page 237) VER CLASS MAJOR MINOR DID1, type RO, offset 0x004, reset - (see page 239) VER FAM PARTNO PINCOUNT TEMP PKG ROHS QUAL DC0, type RO, offset 0x008, reset 0x007F.007F (see page 241) SRAMSZ FLASHSZ DC1, type RO, offset 0x010, reset 0x1333.2FFF (see page 242) WDT1 MINSYSDIV CAN1 MAXADC1SPD CAN0 MAXADC0SPD MPU HIB PWM1 PWM0 TEMPSNS PLL SSI1 SSI0 ADC0AIN5 ADC0AIN4 PWM5 PWM4 GPIOF GPIOE ADC1 ADC0 WDT0 SWO SWD JTAG TIMER3 TIMER2 TIMER1 TIMER0 UART2 UART1 UART0 ADC0AIN3 ADC0AIN2 ADC0AIN1 ADC0AIN0 PWM3 PWM2 PWM1 PWM0 GPIOD GPIOC GPIOB GPIOA PWM3 PWM2 PWM1 PWM0 DC2, type RO, offset 0x014, reset 0x070F.F337 (see page 245) EPI0 I2C1HS I2C1 I2S0 I2C0HS COMP2 I2C0 COMP1 COMP0 QEI1 QEI0 CCP1 CCP0 DC3, type RO, offset 0x018, reset 0xBFFF.FFFF (see page 248) 32KHZ PWMFAULT CCP5 C2O CCP4 C2PLUS C2MINUS CCP3 C1O CCP2 C1PLUS C1MINUS C0O ADC0AIN7 ADC0AIN6 C0PLUS C0MINUS DC4, type RO, offset 0x01C, reset 0x0004.F1FF (see page 252) EPHY0 CCP7 CCP6 UDMA EMAC0 E1588 ROM GPIOJ PICAL GPIOH GPIOG PWM7 PWM6 DC5, type RO, offset 0x020, reset 0x0F30.00FF (see page 255) PWMEFLT PWMESYNC PWMFAULT3 PWMFAULT2 PWMFAULT1 PWMFAULT0 PWM5 PWM4 DC6, type RO, offset 0x024, reset 0x0000.0013 (see page 257) USB0PHY USB0 DC7, type RO, offset 0x028, reset 0xFFFF.FFFF (see page 258) DMACH30 DMACH29 DMACH28 DMACH27 DMACH26 DMACH25 DMACH24 DMACH23 DMACH22 DMACH21 DMACH20 DMACH19 DMACH18 DMACH17 DMACH16 DMACH15 DMACH14 DMACH13 DMACH12 DMACH11 DMACH10 DMACH9 DMACH8 DMACH7 DMACH6 DMACH5 DMACH4 DMACH3 DMACH2 DMACH1 DMACH0 DC8, type RO, offset 0x02C, reset 0xFFFF.FFFF (see page 261) ADC1AIN15 ADC1AIN14 ADC1AIN13 ADC1AIN12 ADC1AIN11 ADC1AIN10 ADC1AIN9 ADC1AIN8 ADC1AIN7 ADC1AIN6 ADC1AIN5 ADC1AIN4 ADC1AIN3 ADC1AIN2 ADC1AIN1 ADC1AIN0 ADC0AIN15 ADC0AIN14 ADC0AIN13 ADC0AIN12 ADC0AIN11 ADC0AIN10 ADC0AIN9 ADC0AIN8 ADC0AIN7 ADC0AIN6 ADC0AIN5 ADC0AIN4 ADC0AIN3 ADC0AIN2 ADC0AIN1 ADC0AIN0 PBORCTL, type R/W, offset 0x030, reset 0x0000.0000 (see page 264) BORIOR SRCR0, type RO, offset 0x040, reset 0x0000.0000 (see page 265) WDT1 CAN1 CAN0 PWM0 HIB ADC1 ADC0 TIMER2 TIMER1 TIMER0 UART2 UART1 UART0 GPIOC GPIOB GPIOA WDT0 SRCR1, type RO, offset 0x044, reset 0x0000.0000 (see page 267) COMP2 I2C1 I2C0 COMP1 COMP0 QEI1 QEI0 TIMER3 SSI1 SSI0 GPIOF GPIOE SRCR2, type RO, offset 0x048, reset 0x0000.0000 (see page 270) USB0 UDMA GPIOJ GPIOH GPIOG GPIOD RIS, type RO, offset 0x050, reset 0x0000.0000 (see page 272) MOSCPUPRIS USBPLLLRIS PLLLRIS 1438 MOFRIS BORRIS November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 IMC, type R/W, offset 0x054, reset 0x0000.0000 (see page 274) MOSCPUPIM USBPLLLIM PLLLIM MOFIM BORIM MOSCPUPMIS USBPLLLMIS PLLLMIS MOFMIS BORMIS MISC, type R/W1C, offset 0x058, reset 0x0000.0000 (see page 276) RESC, type R/W, offset 0x05C, reset - (see page 278) MOSCFAIL WDT1 SW WDT0 BOR POR EXT RCC, type R/W, offset 0x060, reset 0x078E.3D51 (see page 280) ACG PWRDN SYSDIV BYPASS USESYSDIV XTAL PWMDIV USEPWMDIV OSCSRC IOSCDIS MOSCDIS GPIOHBCTL, type R/W, offset 0x06C, reset 0x0000.7E00 (see page 285) PORTQ PORTP PORTN PORTM PORTL PORTK PORTJ PORTH PORTG PORTF PORTE PORTD PORTC PORTB PORTA NOXTAL MOSCIM CVAL ADC1 ADC0 TIMER2 TIMER1 TIMER0 UART2 UART1 UART0 GPIOC GPIOB GPIOA ADC1 ADC0 TIMER2 TIMER1 TIMER0 UART2 UART1 UART0 GPIOC GPIOB GPIOA ADC1 ADC0 TIMER2 TIMER1 TIMER0 UART2 UART1 UART0 GPIOC GPIOB GPIOA RCC2, type R/W, offset 0x070, reset 0x07C0.6810 (see page 289) USERCC2 DIV400 USBPWRDN SYSDIV2 PWRDN2 SYSDIV2LSB BYPASS2 OSCSRC2 MOSCCTL, type R/W, offset 0x07C, reset 0x0000.0000 (see page 292) RCGC0, type RO, offset 0x100, reset 0x0000.0040 (see page 293) WDT1 CAN1 MAXADC1SPD CAN0 PWM0 MAXADC0SPD HIB WDT0 RCGC1, type RO, offset 0x104, reset 0x0000.0000 (see page 296) COMP2 I2C1 I2C0 COMP1 COMP0 QEI1 QEI0 TIMER3 SSI1 SSI0 GPIOF GPIOE RCGC2, type RO, offset 0x108, reset 0x0000.0000 (see page 300) USB0 UDMA GPIOJ GPIOH GPIOG GPIOD SCGC0, type RO, offset 0x110, reset 0x0000.0040 (see page 303) WDT1 CAN1 CAN0 PWM0 HIB WDT0 SCGC1, type RO, offset 0x114, reset 0x0000.0000 (see page 306) COMP2 I2C1 I2C0 COMP1 COMP0 QEI1 QEI0 TIMER3 SSI1 SSI0 GPIOF GPIOE SCGC2, type RO, offset 0x118, reset 0x0000.0000 (see page 310) USB0 UDMA GPIOJ GPIOH GPIOG GPIOD DCGC0, type RO, offset 0x120, reset 0x0000.0040 (see page 313) WDT1 CAN1 CAN0 PWM0 HIB WDT0 DCGC1, type RO, offset 0x124, reset 0x0000.0000 (see page 316) COMP2 I2C1 I2C0 COMP1 COMP0 QEI1 QEI0 TIMER3 SSI1 SSI0 GPIOF GPIOE DCGC2, type RO, offset 0x128, reset 0x0000.0000 (see page 320) USB0 UDMA GPIOJ GPIOH GPIOG GPIOD DSLPCLKCFG, type R/W, offset 0x144, reset 0x0780.0000 (see page 323) DSDIVORIDE DSOSCSRC November 08, 2011 1439 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 SYSPROP, type RO, offset 0x14C, reset 0x0000.1D31 (see page 325) FPU PIOSCCAL, type R/W, offset 0x150, reset 0x0000.0000 (see page 326) UTEN CAL UPDATE UT PIOSCSTAT, type RO, offset 0x154, reset 0x0000.0040 (see page 328) DT RESULT CT PLLFREQ0, type RO, offset 0x160, reset 0x0000.0032 (see page 329) MFRAC MFRAC MINT PLLFREQ1, type RO, offset 0x164, reset 0x0000.0001 (see page 330) Q N PLLSTAT, type RO, offset 0x168, reset 0x0000.0000 (see page 331) LOCK DC9, type RO, offset 0x190, reset 0x00FF.00FF (see page 332) ADC1DC7 ADC1DC6 ADC1DC5 ADC1DC4 ADC1DC3 ADC1DC2 ADC1DC1 ADC1DC0 ADC0DC7 ADC0DC6 ADC0DC5 ADC0DC4 ADC0DC3 ADC0DC2 ADC0DC1 ADC0DC0 NVMSTAT, type RO, offset 0x1A0, reset 0x0000.0001 (see page 334) FWB PPWD, type RO, offset 0x300, reset 0x0000.0003 (see page 335) P1 P0 PPTIMER, type RO, offset 0x304, reset 0x0000.003F (see page 336) P5 P4 P3 P2 P1 P0 P5 P4 P3 P2 P1 P0 PPGPIO, type RO, offset 0x308, reset 0x0000.7FFF (see page 338) P14 P13 P12 P11 P10 P9 P8 P7 P6 PPDMA, type RO, offset 0x30C, reset 0x0000.0001 (see page 341) P0 PPHIB, type RO, offset 0x314, reset 0x0000.0001 (see page 342) P0 PPUART, type RO, offset 0x318, reset 0x0000.00FF (see page 343) P7 P6 P5 P4 P3 P2 P1 P0 P3 P2 P1 P0 P3 P2 P1 P0 PPSSI, type RO, offset 0x31C, reset 0x0000.000F (see page 345) PPI2C, type RO, offset 0x320, reset 0x0000.003F (see page 347) P5 P4 PPUSB, type RO, offset 0x328, reset 0x0000.0001 (see page 349) P0 1440 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 P1 P0 P1 P0 PPCAN, type RO, offset 0x334, reset 0x0000.0003 (see page 350) PPADC, type RO, offset 0x338, reset 0x0000.0003 (see page 351) PPACMP, type RO, offset 0x33C, reset 0x0000.0001 (see page 352) P0 PPPWM, type RO, offset 0x340, reset 0x0000.0003 (see page 353) P1 P0 P1 P0 PPQEI, type RO, offset 0x344, reset 0x0000.0003 (see page 354) PPEEPROM, type RO, offset 0x358, reset 0x0000.0001 (see page 355) P0 PPWTIMER, type RO, offset 0x35C, reset 0x0000.003F (see page 356) P5 P4 P3 P2 P1 P0 R1 R0 SRWD, type R/W, offset 0x500, reset 0x0000.0000 (see page 358) SRTIMER, type R/W, offset 0x504, reset 0x0000.0000 (see page 360) R5 R4 R3 R2 R1 R0 R5 R4 R3 R2 R1 R0 SRGPIO, type R/W, offset 0x508, reset 0x0000.0000 (see page 362) R14 R13 R12 R11 R10 R9 R8 R7 R6 SRDMA, type R/W, offset 0x50C, reset 0x0000.0000 (see page 365) R0 SRHIB, type R/W, offset 0x514, reset 0x0000.0000 (see page 366) R0 SRUART, type R/W, offset 0x518, reset 0x0000.0000 (see page 367) R7 R6 R5 R4 R3 R2 R1 R0 R3 R2 R1 R0 R3 R2 R1 R0 SRSSI, type R/W, offset 0x51C, reset 0x0000.0000 (see page 369) SRI2C, type R/W, offset 0x520, reset 0x0000.0000 (see page 371) R5 R4 SRUSB, type R/W, offset 0x528, reset 0x0000.0000 (see page 373) R0 SRCAN, type R/W, offset 0x534, reset 0x0000.0000 (see page 374) R1 November 08, 2011 R0 1441 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R1 R0 SRADC, type R/W, offset 0x538, reset 0x0000.0000 (see page 376) SRACMP, type R/W, offset 0x53C, reset 0x0000.0000 (see page 378) R0 SRPWM, type R/W, offset 0x540, reset 0x0000.0000 (see page 379) R1 R0 R1 R0 SRQEI, type R/W, offset 0x544, reset 0x0000.0000 (see page 381) SREEPROM, type R/W, offset 0x558, reset 0x0000.0000 (see page 383) R0 SRWTIMER, type R/W, offset 0x55C, reset 0x0000.0000 (see page 384) R5 R4 R3 R2 R1 R0 R1 R0 RCGCWD, type R/W, offset 0x600, reset 0x0000.0000 (see page 386) RCGCTIMER, type R/W, offset 0x604, reset 0x0000.0000 (see page 387) R5 R4 R3 R2 R1 R0 R5 R4 R3 R2 R1 R0 RCGCGPIO, type R/W, offset 0x608, reset 0x0000.0000 (see page 389) R14 R13 R12 R11 R10 R9 R8 R7 R6 RCGCDMA, type R/W, offset 0x60C, reset 0x0000.0000 (see page 392) R0 RCGCHIB, type R/W, offset 0x614, reset 0x0000.0001 (see page 393) R0 RCGCUART, type R/W, offset 0x618, reset 0x0000.0000 (see page 394) R7 R6 R5 R4 R3 R2 R1 R0 R3 R2 R1 R0 R3 R2 R1 R0 RCGCSSI, type R/W, offset 0x61C, reset 0x0000.0000 (see page 396) RCGCI2C, type R/W, offset 0x620, reset 0x0000.0000 (see page 398) R5 R4 RCGCUSB, type R/W, offset 0x628, reset 0x0000.0000 (see page 400) R0 RCGCCAN, type R/W, offset 0x634, reset 0x0000.0000 (see page 401) R1 R0 R1 R0 RCGCADC, type R/W, offset 0x638, reset 0x0000.0000 (see page 402) 1442 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RCGCACMP, type R/W, offset 0x63C, reset 0x0000.0000 (see page 403) R0 RCGCPWM, type R/W, offset 0x640, reset 0x0000.0000 (see page 404) R1 R0 R1 R0 RCGCQEI, type R/W, offset 0x644, reset 0x0000.0000 (see page 405) RCGCEEPROM, type R/W, offset 0x658, reset 0x0000.0000 (see page 406) R0 RCGCWTIMER, type R/W, offset 0x65C, reset 0x0000.0000 (see page 407) R5 R4 R3 R2 R1 R0 S1 S0 SCGCWD, type R/W, offset 0x700, reset 0x0000.0000 (see page 409) SCGCTIMER, type R/W, offset 0x704, reset 0x0000.0000 (see page 410) S5 S4 S3 S2 S1 S0 S5 S4 S3 S2 S1 S0 SCGCGPIO, type R/W, offset 0x708, reset 0x0000.0000 (see page 412) S14 S13 S12 S11 S10 S9 S8 S7 S6 SCGCDMA, type R/W, offset 0x70C, reset 0x0000.0000 (see page 415) S0 SCGCHIB, type R/W, offset 0x714, reset 0x0000.0001 (see page 416) S0 SCGCUART, type R/W, offset 0x718, reset 0x0000.0000 (see page 417) S7 S6 S5 S4 S3 S2 S1 S0 S3 S2 S1 S0 S3 S2 S1 S0 SCGCSSI, type R/W, offset 0x71C, reset 0x0000.0000 (see page 419) SCGCI2C, type R/W, offset 0x720, reset 0x0000.0000 (see page 421) S5 S4 SCGCUSB, type R/W, offset 0x728, reset 0x0000.0000 (see page 423) S0 SCGCCAN, type R/W, offset 0x734, reset 0x0000.0000 (see page 424) S1 S0 S1 S0 SCGCADC, type R/W, offset 0x738, reset 0x0000.0000 (see page 425) SCGCACMP, type R/W, offset 0x73C, reset 0x0000.0000 (see page 426) S0 November 08, 2011 1443 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 S1 S0 S1 S0 SCGCPWM, type R/W, offset 0x740, reset 0x0000.0000 (see page 427) SCGCQEI, type R/W, offset 0x744, reset 0x0000.0000 (see page 428) SCGCEEPROM, type R/W, offset 0x758, reset 0x0000.0000 (see page 429) S0 SCGCWTIMER, type R/W, offset 0x75C, reset 0x0000.0000 (see page 430) S5 S4 S3 S2 S1 S0 D1 D0 DCGCWD, type R/W, offset 0x800, reset 0x0000.0000 (see page 432) DCGCTIMER, type R/W, offset 0x804, reset 0x0000.0000 (see page 433) D5 D4 D3 D2 D1 D0 D5 D4 D3 D2 D1 D0 DCGCGPIO, type R/W, offset 0x808, reset 0x0000.0000 (see page 435) D14 D13 D12 D11 D10 D9 D8 D7 D6 DCGCDMA, type R/W, offset 0x80C, reset 0x0000.0000 (see page 438) D0 DCGCHIB, type R/W, offset 0x814, reset 0x0000.0001 (see page 439) D0 DCGCUART, type R/W, offset 0x818, reset 0x0000.0000 (see page 440) D7 D6 D5 D4 D3 D2 D1 D0 D3 D2 D1 D0 D3 D2 D1 D0 DCGCSSI, type R/W, offset 0x81C, reset 0x0000.0000 (see page 442) DCGCI2C, type R/W, offset 0x820, reset 0x0000.0000 (see page 444) D5 D4 DCGCUSB, type R/W, offset 0x828, reset 0x0000.0000 (see page 446) D0 DCGCCAN, type R/W, offset 0x834, reset 0x0000.0000 (see page 447) D1 D0 D1 D0 DCGCADC, type R/W, offset 0x838, reset 0x0000.0000 (see page 448) DCGCACMP, type R/W, offset 0x83C, reset 0x0000.0000 (see page 449) D0 DCGCPWM, type R/W, offset 0x840, reset 0x0000.0000 (see page 450) D1 1444 D0 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 D1 D0 DCGCQEI, type R/W, offset 0x844, reset 0x0000.0000 (see page 451) DCGCEEPROM, type R/W, offset 0x858, reset 0x0000.0000 (see page 452) D0 DCGCWTIMER, type R/W, offset 0x85C, reset 0x0000.0000 (see page 453) D5 D4 D3 D2 D1 D0 P1 P0 PCWD, type R/W, offset 0x900, reset 0x0000.0003 (see page 455) PCTIMER, type R/W, offset 0x904, reset 0x0000.003F (see page 457) P5 P4 P3 P2 P1 P0 P5 P4 P3 P2 P1 P0 PCGPIO, type R/W, offset 0x908, reset 0x0000.7FFF (see page 460) P14 P13 P12 P11 P10 P9 P8 P7 P6 PCDMA, type R/W, offset 0x90C, reset 0x0000.0001 (see page 466) P0 PCHIB, type R/W, offset 0x914, reset 0x0000.0001 (see page 467) P0 PCUART, type R/W, offset 0x918, reset 0x0000.00FF (see page 468) P7 P6 P5 P4 P3 P2 P1 P0 P3 P2 P1 P0 P3 P2 P1 P0 PCSSI, type R/W, offset 0x91C, reset 0x0000.000F (see page 472) PCI2C, type R/W, offset 0x920, reset 0x0000.003F (see page 474) P5 P4 PCUSB, type R/W, offset 0x928, reset 0x0000.0001 (see page 477) P0 PCCAN, type R/W, offset 0x934, reset 0x0000.0003 (see page 478) P1 P0 P1 P0 PCADC, type R/W, offset 0x938, reset 0x0000.0003 (see page 480) PCACMP, type R/W, offset 0x93C, reset 0x0000.0001 (see page 482) P0 PCPWM, type R/W, offset 0x940, reset 0x0000.0003 (see page 483) P1 P0 P1 P0 PCQEI, type R/W, offset 0x944, reset 0x0000.0003 (see page 485) November 08, 2011 1445 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PCEEPROM, type R/W, offset 0x958, reset 0x0000.0001 (see page 487) P0 PCWTIMER, type R/W, offset 0x95C, reset 0x0000.0000 (see page 488) P5 P4 P3 P2 P1 P0 R1 R0 PRWD, type R/W, offset 0xA00, reset 0x0000.0000 (see page 491) PRTIMER, type R/W, offset 0xA04, reset 0x0000.0000 (see page 492) R5 R4 R3 R2 R1 R0 R5 R4 R3 R2 R1 R0 PRGPIO, type R/W, offset 0xA08, reset 0x0000.0000 (see page 494) R14 R13 R12 R11 R10 R9 R8 R7 R6 PRDMA, type R/W, offset 0xA0C, reset 0x0000.0000 (see page 497) R0 PRHIB, type R/W, offset 0xA14, reset 0x0000.0001 (see page 498) R0 PRUART, type R/W, offset 0xA18, reset 0x0000.0000 (see page 499) R7 R6 R5 R4 R3 R2 R1 R0 R3 R2 R1 R0 R3 R2 R1 R0 PRSSI, type R/W, offset 0xA1C, reset 0x0000.0000 (see page 501) PRI2C, type R/W, offset 0xA20, reset 0x0000.0000 (see page 503) R5 R4 PRUSB, type R/W, offset 0xA28, reset 0x0000.0000 (see page 505) R0 PRCAN, type R/W, offset 0xA34, reset 0x0000.0000 (see page 506) R1 R0 R1 R0 PRADC, type R/W, offset 0xA38, reset 0x0000.0000 (see page 507) PRACMP, type R/W, offset 0xA3C, reset 0x0000.0000 (see page 508) R0 PRPWM, type R/W, offset 0xA40, reset 0x0000.0000 (see page 509) R1 R0 R1 R0 PRQEI, type R/W, offset 0xA44, reset 0x0000.0000 (see page 510) PREEPROM, type R/W, offset 0xA58, reset 0x0000.0000 (see page 511) R0 1446 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R5 R4 R3 R2 R1 R0 FPIXCRIS FPOFCRIS FPUFCRIS FPIOCRIS FPDZCRIS FPIDCRIS PRWTIMER, type R/W, offset 0xA5C, reset 0x0000.0000 (see page 512) System Exception Module Base 0x400F.9000 SYSEXCRIS, type RO, offset 0x000, reset 0x0000.0000 (see page 515) SYSEXCIM, type R/W, offset 0x004, reset 0x0000.0000 (see page 517) FPIXCIM FPOFCIM FPUFCIM FPIOCIM FPDZCIM FPIDCIM SYSEXCMIS, type RO, offset 0x008, reset 0x0000.0000 (see page 519) FPIXCMIS FPOFCMIS FPUFCMIS FPIOCMIS FPDZCMIS FPIDCMIS SYSEXCIC, type W1C, offset 0x00C, reset 0x0000.0000 (see page 521) FPIXCIC FPOFCIC FPUFCIC FPIOCIC FPDZCIC FPIDCIC Hibernation Module Base 0x400F.C000 HIBRTCC, type RO, offset 0x000, reset 0x0000.0000 (see page 535) RTCC RTCC HIBRTCM0, type R/W, offset 0x004, reset 0xFFFF.FFFF (see page 536) RTCM0 RTCM0 HIBRTCLD, type R/W, offset 0x00C, reset 0x0000.0000 (see page 537) RTCLD RTCLD HIBCTL, type R/W, offset 0x010, reset 0x8000.0000 (see page 538) WRC OSCHYS OSCDRV OSCBYP VBATSEL BATCHK BATWKEN VDD3ON VABORT CLK32EN LOWBATEN PINWEN RTCWEN HIBREQ RTCEN HIBIM, type R/W, offset 0x014, reset 0x0000.0000 (see page 542) WC EXTW LOWBAT RTCALT0 WC EXTW LOWBAT RTCALT0 WC EXTW LOWBAT RTCALT0 WC EXTW LOWBAT RTCALT0 HIBRIS, type RO, offset 0x018, reset 0x0000.0000 (see page 544) HIBMIS, type RO, offset 0x01C, reset 0x0000.0000 (see page 546) HIBIC, type R/W1C, offset 0x020, reset 0x0000.0000 (see page 548) HIBRTCT, type R/W, offset 0x024, reset 0x0000.7FFF (see page 549) TRIM HIBRTCSS, type R/W, offset 0x028, reset 0x7FFF.0000 (see page 550) RTCSSM RTCSSC HIBDATA, type R/W, offset 0x030-0x06F, reset - (see page 551) RTD RTD November 08, 2011 1447 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Internal Memory Flash Memory Registers (Flash Control Offset) Base 0x400F.D000 FMA, type R/W, offset 0x000, reset 0x0000.0000 OFFSET OFFSET FMD, type R/W, offset 0x004, reset 0x0000.0000 DATA DATA FMC, type R/W, offset 0x008, reset 0x0000.0000 WRKEY COMT MERASE ERASE WRITE ERIS PRIS ARIS EMASK PMASK AMASK EMISC PMISC AMISC FCRIS, type RO, offset 0x00C, reset 0x0000.0000 PROGRIS ERRIS INVDRIS VOLTRIS FCIM, type R/W, offset 0x010, reset 0x0000.0000 PROGMASK ERMASK INVDMASK VOLTMASK FCMISC, type R/W1C, offset 0x014, reset 0x0000.0000 PROGMISC ERMISC INVDMISC VOLTMISC FMC2, type R/W, offset 0x020, reset 0x0000.0000 WRKEY WRBUF FWBVAL, type R/W, offset 0x030, reset 0x0000.0000 FWB[n] FWB[n] FWBn, type R/W, offset 0x100 - 0x17C, reset 0x0000.0000 DATA DATA FSIZE, type RO, offset 0xFC0, reset 0x0000.007F SIZE SSIZE, type RO, offset 0xFC4, reset 0x0000.007F SIZE ROMSWMAP, type RO, offset 0xFCC, reset 0x0000.0000 SAFERTOS Internal Memory EEPROM Registers (EEPROM Control Offset) Base 0x400A.F000 EESIZE, type RO, offset 0x000, reset 0x0020.0200 BLKCNT WORDCNT EEBLOCK, type R/W, offset 0x004, reset 0x0000.0000 BLOCK EEOFFSET, type R/W, offset 0x008, reset 0x0000.0000 OFFSET 1448 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 EERDWR, type R/W, offset 0x010, reset VALUE VALUE EERDWRINC, type R/W, offset 0x014, reset VALUE VALUE EEDONE, type RO, offset 0x018, reset 0x0000.0000 INVPL WRBUSY NOPERM WKCOPY WKERASE WORKING EESUPP, type R/W, offset 0x01C, reset - PRETRY ERETRY EREQ START EEUNLOCK, type R/W, offset 0x020, reset UNLOCK UNLOCK EEPROT, type R/W, offset 0x030, reset 0x0000.0000 ACC PROT EEPASS0, type R/W, offset 0x034, reset PASS PASS EEPASS1, type R/W, offset 0x038, reset PASS PASS EEPASS2, type R/W, offset 0x03C, reset PASS PASS EEINT, type R/W, offset 0x040, reset 0x0000.0000 INT EEHIDE, type R/W, offset 0x050, reset 0x0000.0000 Hn Hn EEDBGME, type R/W, offset 0x080, reset 0x0000.0000 KEY ME EEPROMPP, type RO, offset 0xFC0, reset 0x0000.001F SIZE Internal Memory Memory Registers (System Control Offset) Base 0x400F.E000 RMCTL, type R/W1C, offset 0x0F0, reset - BA FMPRE0, type R/W, offset 0x130 and 0x200, reset 0xFFFF.FFFF READ_ENABLE READ_ENABLE FMPRE1, type R/W, offset 0x204, reset 0xFFFF.FFFF READ_ENABLE READ_ENABLE November 08, 2011 1449 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DBG1 DBG0 FMPRE2, type R/W, offset 0x208, reset 0xFFFF.FFFF READ_ENABLE READ_ENABLE FMPRE3, type R/W, offset 0x20C, reset 0xFFFF.FFFF READ_ENABLE READ_ENABLE FMPPE0, type R/W, offset 0x134 and 0x400, reset 0xFFFF.FFFF PROG_ENABLE PROG_ENABLE FMPPE1, type R/W, offset 0x404, reset 0xFFFF.FFFF PROG_ENABLE PROG_ENABLE FMPPE2, type R/W, offset 0x408, reset 0xFFFF.FFFF PROG_ENABLE PROG_ENABLE FMPPE3, type R/W, offset 0x40C, reset 0xFFFF.FFFF PROG_ENABLE PROG_ENABLE BOOTCFG, type RO, offset 0x1D0, reset 0xFFFF.FFFE NW PORT PIN POL EN USER_REG0, type R/W, offset 0x1E0, reset 0xFFFF.FFFF DATA DATA USER_REG1, type R/W, offset 0x1E4, reset 0xFFFF.FFFF DATA DATA USER_REG2, type R/W, offset 0x1E8, reset 0xFFFF.FFFF DATA DATA USER_REG3, type R/W, offset 0x1EC, reset 0xFFFF.FFFF DATA DATA Micro Direct Memory Access (μDMA) μDMA Channel Control Structure (Offset from Channel Control Table Base) Base n/a DMASRCENDP, type R/W, offset 0x000, reset ADDR ADDR DMADSTENDP, type R/W, offset 0x004, reset ADDR ADDR DMACHCTL, type R/W, offset 0x008, reset DSTINC DSTSIZE SRCINC ARBSIZE SRCSIZE ARBSIZE XFERSIZE NXTUSEBURST XFERMODE Micro Direct Memory Access (μDMA) μDMA Registers (Offset from μDMA Base Address) Base 0x400F.F000 DMASTAT, type RO, offset 0x000, reset 0x001F.0000 DMACHANS STATE 1450 MASTEN November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DMACFG, type WO, offset 0x004, reset - MASTEN DMACTLBASE, type R/W, offset 0x008, reset 0x0000.0000 ADDR ADDR DMAALTBASE, type RO, offset 0x00C, reset 0x0000.0200 ADDR ADDR DMAWAITSTAT, type RO, offset 0x010, reset 0xFFFF.FFC0 WAITREQ[n] WAITREQ[n] DMASWREQ, type WO, offset 0x014, reset SWREQ[n] SWREQ[n] DMAUSEBURSTSET, type R/W, offset 0x018, reset 0x0000.0000 SET[n] SET[n] DMAUSEBURSTCLR, type WO, offset 0x01C, reset CLR[n] CLR[n] DMAREQMASKSET, type R/W, offset 0x020, reset 0x0000.0000 SET[n] SET[n] DMAREQMASKCLR, type WO, offset 0x024, reset CLR[n] CLR[n] DMAENASET, type R/W, offset 0x028, reset 0x0000.0000 SET[n] SET[n] DMAENACLR, type WO, offset 0x02C, reset CLR[n] CLR[n] DMAALTSET, type R/W, offset 0x030, reset 0x0000.0000 SET[n] SET[n] DMAALTCLR, type WO, offset 0x034, reset CLR[n] CLR[n] DMAPRIOSET, type R/W, offset 0x038, reset 0x0000.0000 SET[n] SET[n] DMAPRIOCLR, type WO, offset 0x03C, reset CLR[n] CLR[n] DMAERRCLR, type R/W, offset 0x04C, reset 0x0000.0000 ERRCLR DMACHASGN, type R/W, offset 0x500, reset 0x0000.0000 CHASGN[n] CHASGN[n] November 08, 2011 1451 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DMACHIS, type R/W1C, offset 0x504, reset 0x0000.0000 CHIS[n] CHIS[n] DMACHMAP0, type R/W, offset 0x510, reset 0x0000.0000 CH7SEL CH6SEL CH5SEL CH4SEL CH3SEL CH2SEL CH1SEL CH0SEL CH15SEL CH14SEL CH13SEL CH12SEL CH11SEL CH10SEL CH9SEL CH8SEL CH23SEL CH22SEL CH21SEL CH20SEL CH19SEL CH18SEL CH17SEL CH16SEL CH31SEL CH30SEL CH29SEL CH28SEL CH27SEL CH26SEL CH25SEL CH24SEL DMACHMAP1, type R/W, offset 0x514, reset 0x0000.0000 DMACHMAP2, type R/W, offset 0x518, reset 0x0000.0000 DMACHMAP3, type R/W, offset 0x51C, reset 0x0000.0000 DMAPeriphID0, type RO, offset 0xFE0, reset 0x0000.0030 PID0 DMAPeriphID1, type RO, offset 0xFE4, reset 0x0000.00B2 PID1 DMAPeriphID2, type RO, offset 0xFE8, reset 0x0000.000B PID2 DMAPeriphID3, type RO, offset 0xFEC, reset 0x0000.0000 PID3 DMAPeriphID4, type RO, offset 0xFD0, reset 0x0000.0004 PID4 DMAPCellID0, type RO, offset 0xFF0, reset 0x0000.000D CID0 DMAPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 CID1 DMAPCellID2, type RO, offset 0xFF8, reset 0x0000.0005 CID2 DMAPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 CID3 1452 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 General-Purpose Input/Outputs (GPIOs) GPIO Port A (APB) base: 0x4000.4000 GPIO Port A (AHB) base: 0x4005.8000 GPIO Port B (APB) base: 0x4000.5000 GPIO Port B (AHB) base: 0x4005.9000 GPIO Port C (APB) base: 0x4000.6000 GPIO Port C (AHB) base: 0x4005.A000 GPIO Port D (APB) base: 0x4000.7000 GPIO Port D (AHB) base: 0x4005.B000 GPIO Port E (APB) base: 0x4002.4000 GPIO Port E (AHB) base: 0x4005.C000 GPIO Port F (APB) base: 0x4002.5000 GPIO Port F (AHB) base: 0x4005.D000 GPIO Port G (APB) base: 0x4002.6000 GPIO Port G (AHB) base: 0x4005.E000 GPIO Port H (APB) base: 0x4002.7000 GPIO Port H (AHB) base: 0x4005.F000 GPIO Port J (APB) base: 0x4003.D000 GPIO Port J (AHB) base: 0x4006.0000 GPIO Port K (AHB) base: 0x4006.1000 GPIO Port L (AHB) base: 0x4006.2000 GPIO Port M (AHB) base: 0x4006.3000 GPIO Port N (AHB) base: 0x4006.4000 GPIO Port P (AHB) base: 0x4006.5000 GPIO Port Q (AHB) base: 0x4006.6000 GPIODATA, type R/W, offset 0x000, reset 0x0000.0000 (see page 688) DATA GPIODIR, type R/W, offset 0x400, reset 0x0000.0000 (see page 690) DIR GPIOIS, type R/W, offset 0x404, reset 0x0000.0000 (see page 691) IS GPIOIBE, type R/W, offset 0x408, reset 0x0000.0000 (see page 692) IBE GPIOIEV, type R/W, offset 0x40C, reset 0x0000.0000 (see page 693) IEV GPIOIM, type R/W, offset 0x410, reset 0x0000.0000 (see page 694) IME GPIORIS, type RO, offset 0x414, reset 0x0000.0000 (see page 695) RIS GPIOMIS, type RO, offset 0x418, reset 0x0000.0000 (see page 696) MIS GPIOICR, type W1C, offset 0x41C, reset 0x0000.0000 (see page 697) IC GPIOAFSEL, type R/W, offset 0x420, reset - (see page 698) AFSEL GPIODR2R, type R/W, offset 0x500, reset 0x0000.00FF (see page 700) DRV2 November 08, 2011 1453 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 GPIODR4R, type R/W, offset 0x504, reset 0x0000.0000 (see page 701) DRV4 GPIODR8R, type R/W, offset 0x508, reset 0x0000.0000 (see page 702) DRV8 GPIOODR, type R/W, offset 0x50C, reset 0x0000.0000 (see page 704) ODE GPIOPUR, type R/W, offset 0x510, reset - (see page 705) PUE GPIOPDR, type R/W, offset 0x514, reset 0x0000.0000 (see page 707) PDE GPIOSLR, type R/W, offset 0x518, reset 0x0000.0000 (see page 709) SRL GPIODEN, type R/W, offset 0x51C, reset - (see page 710) DEN GPIOLOCK, type R/W, offset 0x520, reset 0x0000.0001 (see page 712) LOCK LOCK GPIOCR, type -, offset 0x524, reset - (see page 713) CR GPIOAMSEL, type R/W, offset 0x528, reset 0x0000.0000 (see page 715) GPIOAMSEL GPIOPCTL, type R/W, offset 0x52C, reset - (see page 717) PMC7 PMC6 PMC5 PMC4 PMC3 PMC2 PMC1 PMC0 GPIOADCCTL, type R/W, offset 0x530, reset 0x0000.0000 (see page 719) ADCEN GPIODMACTL, type R/W, offset 0x534, reset 0x0000.0000 (see page 720) DMAEN GPIOSI, type R/W, offset 0x538, reset 0x0000.0000 (see page 721) SUM GPIOPeriphID4, type RO, offset 0xFD0, reset 0x0000.0000 (see page 722) PID4 GPIOPeriphID5, type RO, offset 0xFD4, reset 0x0000.0000 (see page 723) PID5 GPIOPeriphID6, type RO, offset 0xFD8, reset 0x0000.0000 (see page 724) PID6 1454 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 GPIOPeriphID7, type RO, offset 0xFDC, reset 0x0000.0000 (see page 725) PID7 GPIOPeriphID0, type RO, offset 0xFE0, reset 0x0000.0061 (see page 726) PID0 GPIOPeriphID1, type RO, offset 0xFE4, reset 0x0000.0000 (see page 727) PID1 GPIOPeriphID2, type RO, offset 0xFE8, reset 0x0000.0018 (see page 728) PID2 GPIOPeriphID3, type RO, offset 0xFEC, reset 0x0000.0001 (see page 729) PID3 GPIOPCellID0, type RO, offset 0xFF0, reset 0x0000.000D (see page 730) CID0 GPIOPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 (see page 731) CID1 GPIOPCellID2, type RO, offset 0xFF8, reset 0x0000.0005 (see page 732) CID2 GPIOPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 (see page 733) CID3 General-Purpose Timers 16/32-bit Timer 0 base: 0x4003.0000 16/32-bit Timer 1 base: 0x4003.1000 16/32-bit Timer 2 base: 0x4003.2000 16/32-bit Timer 3 base: 0x4003.3000 16/32-bit Timer 4 base: 0x4003.4000 16/32-bit Timer 5 base: 0x4003.5000 32/64-bit Wide Timer 0 base: 0x4003.6000 32/64-bit Wide Timer 1 base: 0x4003.7000 32/64-bit Wide Timer 2 base: 0x4004.C000 32/64-bit Wide Timer 3 base: 0x4004.D000 32/64-bit Wide Timer 4 base: 0x4004.E000 32/64-bit Wide Timer 5 base: 0x4004.F000 GPTMCFG, type R/W, offset 0x000, reset 0x0000.0000 (see page 758) GPTMCFG GPTMTAMR, type R/W, offset 0x004, reset 0x0000.0000 (see page 760) TAPLO TAMRSU TAPWMIE TAILD TASNAPS TAWOT TAMIE TACDIR TAAMS TACMR TAMR TBILD TBSNAPS TBWOT TBMIE TBCDIR TBAMS TBCMR TBMR TAPWML TAOTE RTCEN GPTMTBMR, type R/W, offset 0x008, reset 0x0000.0000 (see page 764) TBPLO TBMRSU TBPWMIE GPTMCTL, type R/W, offset 0x00C, reset 0x0000.0000 (see page 768) TBPWML TBOTE TBEVENT TBSTALL TBEN TAEVENT TASTALL TAEN GPTMSYNC, type R/W, offset 0x010, reset 0x0000.0000 (see page 771) SYNCWT1 SYNCWT0 SYNCT5 SYNCT4 SYNCWT5 SYNCWT4 SYNCWT3 SYNCWT2 SYNCT3 SYNCT2 SYNCT1 SYNCT0 November 08, 2011 1455 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CBMIM TBTOIM TAMIM RTCIM CAEIM CAMIM TATOIM CBMRIS TBTORIS TAMRIS RTCRIS CAERIS CAMRIS TATORIS TAMMIS RTCMIS CAEMIS CAMMIS TATOMIS GPTMIMR, type R/W, offset 0x018, reset 0x0000.0000 (see page 775) WUEIM TBMIM CBEIM GPTMRIS, type RO, offset 0x01C, reset 0x0000.0000 (see page 778) WUERIS TBMRIS CBERIS GPTMMIS, type RO, offset 0x020, reset 0x0000.0000 (see page 781) WUEMIS TBMMIS CBEMIS CBMMIS TBTOMIS GPTMICR, type W1C, offset 0x024, reset 0x0000.0000 (see page 784) WUECINT TBMCINT CBECINT CBMCINT TBTOCINT TAMCINT RTCCINT CAECINT CAMCINT TATOCINT GPTMTAILR, type R/W, offset 0x028, reset 0xFFFF.FFFF (see page 786) TAILR TAILR GPTMTBILR, type R/W, offset 0x02C, reset - (see page 787) TBILR TBILR GPTMTAMATCHR, type R/W, offset 0x030, reset 0xFFFF.FFFF (see page 788) TAMR TAMR GPTMTBMATCHR, type R/W, offset 0x034, reset - (see page 789) TBMR TBMR GPTMTAPR, type R/W, offset 0x038, reset 0x0000.0000 (see page 790) TAPSRH TAPSR GPTMTBPR, type R/W, offset 0x03C, reset 0x0000.0000 (see page 791) TBPSRH TBPSR GPTMTAPMR, type R/W, offset 0x040, reset 0x0000.0000 (see page 792) TAPSMRH TAPSMR GPTMTBPMR, type R/W, offset 0x044, reset 0x0000.0000 (see page 793) TBPSMRH TBPSMR GPTMTAR, type RO, offset 0x048, reset 0xFFFF.FFFF (see page 794) TAR TAR GPTMTBR, type RO, offset 0x04C, reset - (see page 795) TBR TBR GPTMTAV, type RW, offset 0x050, reset 0xFFFF.FFFF (see page 796) TAV TAV GPTMTBV, type RW, offset 0x054, reset - (see page 797) TBV TBV GPTMRTCPD, type RO, offset 0x058, reset 0x0000.7FFF (see page 798) RTCPD 1456 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RESEN INTEN GPTMTAPS, type RO, offset 0x05C, reset 0x0000.0000 (see page 799) PSS GPTMTBPS, type RO, offset 0x060, reset 0x0000.0000 (see page 800) PSS GPTMTAPV, type RO, offset 0x064, reset 0x0000.0000 (see page 801) PSV GPTMTBPV, type RO, offset 0x068, reset 0x0000.0000 (see page 802) PSV GPTMPP, type RO, offset 0xFC0, reset 0x0000.0000 (see page 803) SIZE Watchdog Timers WDT0 base: 0x4000.0000 WDT1 base: 0x4000.1000 WDTLOAD, type R/W, offset 0x000, reset 0xFFFF.FFFF (see page 808) WDTLOAD WDTLOAD WDTVALUE, type RO, offset 0x004, reset 0xFFFF.FFFF (see page 809) WDTVALUE WDTVALUE WDTCTL, type R/W, offset 0x008, reset 0x0000.0000 (WDT0) and 0x8000.0000 (WDT1) (see page 810) WRC INTTYPE WDTICR, type WO, offset 0x00C, reset - (see page 812) WDTINTCLR WDTINTCLR WDTRIS, type RO, offset 0x010, reset 0x0000.0000 (see page 813) WDTRIS WDTMIS, type RO, offset 0x014, reset 0x0000.0000 (see page 814) WDTMIS WDTTEST, type R/W, offset 0x418, reset 0x0000.0000 (see page 815) STALL WDTLOCK, type R/W, offset 0xC00, reset 0x0000.0000 (see page 816) WDTLOCK WDTLOCK WDTPeriphID4, type RO, offset 0xFD0, reset 0x0000.0000 (see page 817) PID4 WDTPeriphID5, type RO, offset 0xFD4, reset 0x0000.0000 (see page 818) PID5 WDTPeriphID6, type RO, offset 0xFD8, reset 0x0000.0000 (see page 819) PID6 November 08, 2011 1457 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ASEN3 ASEN2 ASEN1 ASEN0 INR3 INR2 INR1 WDTPeriphID7, type RO, offset 0xFDC, reset 0x0000.0000 (see page 820) PID7 WDTPeriphID0, type RO, offset 0xFE0, reset 0x0000.0005 (see page 821) PID0 WDTPeriphID1, type RO, offset 0xFE4, reset 0x0000.0018 (see page 822) PID1 WDTPeriphID2, type RO, offset 0xFE8, reset 0x0000.0018 (see page 823) PID2 WDTPeriphID3, type RO, offset 0xFEC, reset 0x0000.0001 (see page 824) PID3 WDTPCellID0, type RO, offset 0xFF0, reset 0x0000.000D (see page 825) CID0 WDTPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 (see page 826) CID1 WDTPCellID2, type RO, offset 0xFF8, reset 0x0000.0006 (see page 827) CID2 WDTPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 (see page 828) CID3 Analog-to-Digital Converter (ADC) ADC0 base: 0x4003.8000 ADC1 base: 0x4003.9000 ADCACTSS, type R/W, offset 0x000, reset 0x0000.0000 (see page 850) ADCRIS, type RO, offset 0x004, reset 0x0000.0000 (see page 851) INRDC INR0 ADCIM, type R/W, offset 0x008, reset 0x0000.0000 (see page 853) DCONSS3 DCONSS2 DCONSS1 DCONSS0 MASK3 MASK2 MASK1 MASK0 ADCISC, type R/W1C, offset 0x00C, reset 0x0000.0000 (see page 855) DCINSS3 DCINSS2 DCINSS1 DCINSS0 IN3 IN2 IN1 IN0 OV3 OV2 OV1 OV0 UV1 UV0 ADCOSTAT, type R/W1C, offset 0x010, reset 0x0000.0000 (see page 858) ADCEMUX, type R/W, offset 0x014, reset 0x0000.0000 (see page 860) EM3 EM2 EM1 EM0 ADCUSTAT, type R/W1C, offset 0x018, reset 0x0000.0000 (see page 865) UV3 1458 UV2 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ADCTSSEL, type R/W, offset 0x01C, reset 0x0000.0000 (see page 866) PS3 PS2 PS1 PS0 ADCSSPRI, type R/W, offset 0x020, reset 0x0000.3210 (see page 868) SS3 SS2 SS1 SS0 ADCSPC, type R/W, offset 0x024, reset 0x0000.0000 (see page 870) PHASE ADCPSSI, type R/W, offset 0x028, reset - (see page 872) GSYNC SYNCWAIT SS3 SS2 SS1 SS0 ADCSAC, type R/W, offset 0x030, reset 0x0000.0000 (see page 874) AVG ADCDCISC, type R/W1C, offset 0x034, reset 0x0000.0000 (see page 875) DCINT7 DCINT6 DCINT5 DCINT4 DCINT3 DCINT2 DCINT1 DCINT0 ADCCTL, type R/W, offset 0x038, reset 0x0000.0000 (see page 877) VREF ADCSSMUX0, type R/W, offset 0x040, reset 0x0000.0000 (see page 878) MUX7 MUX6 MUX5 MUX4 MUX3 MUX2 MUX1 MUX0 ADCSSCTL0, type R/W, offset 0x044, reset 0x0000.0000 (see page 880) TS7 IE7 END7 D7 TS6 IE6 END6 D6 TS5 IE5 END5 D5 TS4 IE4 END4 D4 TS3 IE3 END3 D3 TS2 IE2 END2 D2 TS1 IE1 END1 D1 TS0 IE0 END0 D0 ADCSSFIFO0, type RO, offset 0x048, reset - (see page 883) DATA ADCSSFIFO1, type RO, offset 0x068, reset - (see page 883) DATA ADCSSFIFO2, type RO, offset 0x088, reset - (see page 883) DATA ADCSSFIFO3, type RO, offset 0x0A8, reset - (see page 883) DATA ADCSSFSTAT0, type RO, offset 0x04C, reset 0x0000.0100 (see page 884) FULL EMPTY HPTR TPTR EMPTY HPTR TPTR EMPTY HPTR TPTR EMPTY HPTR TPTR ADCSSFSTAT1, type RO, offset 0x06C, reset 0x0000.0100 (see page 884) FULL ADCSSFSTAT2, type RO, offset 0x08C, reset 0x0000.0100 (see page 884) FULL ADCSSFSTAT3, type RO, offset 0x0AC, reset 0x0000.0100 (see page 884) FULL November 08, 2011 1459 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ADCSSOP0, type R/W, offset 0x050, reset 0x0000.0000 (see page 886) S7DCOP S6DCOP S5DCOP S4DCOP S3DCOP S2DCOP S1DCOP S0DCOP ADCSSDC0, type R/W, offset 0x054, reset 0x0000.0000 (see page 888) S7DCSEL S6DCSEL S5DCSEL S4DCSEL S3DCSEL S2DCSEL S1DCSEL S0DCSEL ADCSSEMUX0, type R/W, offset 0x058, reset 0x0000.0000 (see page 890) EMUX7 EMUX6 EMUX5 EMUX4 EMUX3 EMUX2 EMUX1 EMUX0 ADCSSMUX1, type R/W, offset 0x060, reset 0x0000.0000 (see page 892) MUX3 MUX2 MUX1 MUX0 MUX1 MUX0 ADCSSMUX2, type R/W, offset 0x080, reset 0x0000.0000 (see page 892) MUX3 MUX2 ADCSSCTL1, type R/W, offset 0x064, reset 0x0000.0000 (see page 893) TS3 IE3 END3 D3 TS2 IE2 END2 D2 TS1 IE1 END1 D1 TS0 IE0 END0 D0 D2 TS1 IE1 END1 D1 TS0 IE0 END0 D0 ADCSSCTL2, type R/W, offset 0x084, reset 0x0000.0000 (see page 893) TS3 IE3 END3 D3 TS2 IE2 END2 ADCSSOP1, type R/W, offset 0x070, reset 0x0000.0000 (see page 895) S3DCOP S2DCOP S1DCOP S0DCOP S2DCOP S1DCOP S0DCOP ADCSSOP2, type R/W, offset 0x090, reset 0x0000.0000 (see page 895) S3DCOP ADCSSDC1, type R/W, offset 0x074, reset 0x0000.0000 (see page 896) S3DCSEL S2DCSEL S1DCSEL S0DCSEL S1DCSEL S0DCSEL ADCSSDC2, type R/W, offset 0x094, reset 0x0000.0000 (see page 896) S3DCSEL S2DCSEL ADCSSEMUX1, type R/W, offset 0x078, reset 0x0000.0000 (see page 898) EMUX3 EMUX2 EMUX1 EMUX0 EMUX2 EMUX1 EMUX0 ADCSSEMUX2, type R/W, offset 0x098, reset 0x0000.0000 (see page 898) EMUX3 ADCSSMUX3, type R/W, offset 0x0A0, reset 0x0000.0000 (see page 900) MUX0 ADCSSCTL3, type R/W, offset 0x0A4, reset 0x0000.0002 (see page 901) TS0 IE0 END0 D0 ADCSSOP3, type R/W, offset 0x0B0, reset 0x0000.0000 (see page 902) S0DCOP ADCSSDC3, type R/W, offset 0x0B4, reset 0x0000.0000 (see page 903) S0DCSEL 1460 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ADCSSEMUX3, type R/W, offset 0x0B8, reset 0x0000.0000 (see page 904) EMUX0 ADCDCRIC, type R/W, offset 0xD00, reset 0x0000.0000 (see page 905) DCTRIG7 DCTRIG6 DCTRIG5 DCTRIG4 DCTRIG3 DCTRIG2 DCTRIG1 DCTRIG0 DCINT7 DCINT6 DCINT5 DCINT4 DCINT3 DCINT2 DCINT1 DCINT0 ADCDCCTL0, type R/W, offset 0xE00, reset 0x0000.0000 (see page 910) CTE CTC CTM CIE CIC CIM CTM CIE CIC CIM CTM CIE CIC CIM CTM CIE CIC CIM CTM CIE CIC CIM CTM CIE CIC CIM CTM CIE CIC CIM CTM CIE CIC CIM ADCDCCTL1, type R/W, offset 0xE04, reset 0x0000.0000 (see page 910) CTE CTC ADCDCCTL2, type R/W, offset 0xE08, reset 0x0000.0000 (see page 910) CTE CTC ADCDCCTL3, type R/W, offset 0xE0C, reset 0x0000.0000 (see page 910) CTE CTC ADCDCCTL4, type R/W, offset 0xE10, reset 0x0000.0000 (see page 910) CTE CTC ADCDCCTL5, type R/W, offset 0xE14, reset 0x0000.0000 (see page 910) CTE CTC ADCDCCTL6, type R/W, offset 0xE18, reset 0x0000.0000 (see page 910) CTE CTC ADCDCCTL7, type R/W, offset 0xE1C, reset 0x0000.0000 (see page 910) CTE CTC ADCDCCMP0, type R/W, offset 0xE40, reset 0x0000.0000 (see page 913) COMP1 COMP0 ADCDCCMP1, type R/W, offset 0xE44, reset 0x0000.0000 (see page 913) COMP1 COMP0 ADCDCCMP2, type R/W, offset 0xE48, reset 0x0000.0000 (see page 913) COMP1 COMP0 ADCDCCMP3, type R/W, offset 0xE4C, reset 0x0000.0000 (see page 913) COMP1 COMP0 ADCDCCMP4, type R/W, offset 0xE50, reset 0x0000.0000 (see page 913) COMP1 COMP0 ADCDCCMP5, type R/W, offset 0xE54, reset 0x0000.0000 (see page 913) COMP1 COMP0 ADCDCCMP6, type R/W, offset 0xE58, reset 0x0000.0000 (see page 913) COMP1 COMP0 November 08, 2011 1461 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ADCDCCMP7, type R/W, offset 0xE5C, reset 0x0000.0000 (see page 913) COMP1 COMP0 ADCPP, type RO, offset 0xFC0, reset 0x00B0.2187 (see page 914) TS DC RSL TYPE CH MSR ADCPC, type R/W, offset 0xFC4, reset 0x0000.0007 (see page 916) SR ADCCC, type R/W, offset 0xFC8, reset 0x0000.0000 (see page 917) CS Universal Asynchronous Receivers/Transmitters (UARTs) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UART2 base: 0x4000.E000 UART3 base: 0x4000.F000 UART4 base: 0x4001.0000 UART5 base: 0x4001.1000 UART6 base: 0x4001.2000 UART7 base: 0x4001.3000 UARTDR, type R/W, offset 0x000, reset 0x0000.0000 (see page 932) OE BE PE FE DATA UARTRSR/UARTECR, type RO, offset 0x004, reset 0x0000.0000 (Read-Only Status Register) (see page 934) OE BE PE FE BUSY DCD DSR CTS UARTRSR/UARTECR, type WO, offset 0x004, reset 0x0000.0000 (Write-Only Error Clear Register) (see page 934) DATA UARTFR, type RO, offset 0x018, reset 0x0000.0090 (see page 937) RI TXFE RXFF TXFF RXFE UARTILPR, type R/W, offset 0x020, reset 0x0000.0000 (see page 940) ILPDVSR UARTIBRD, type R/W, offset 0x024, reset 0x0000.0000 (see page 941) DIVINT UARTFBRD, type R/W, offset 0x028, reset 0x0000.0000 (see page 942) DIVFRAC UARTLCRH, type R/W, offset 0x02C, reset 0x0000.0000 (see page 943) SPS WLEN FEN STP2 EPS PEN BRK EOT SMART SIRLP SIREN UARTEN UARTCTL, type R/W, offset 0x030, reset 0x0000.0300 (see page 945) CTSEN RTSEN RTS DTR RXE TXE LBE LIN HSE UARTIFLS, type R/W, offset 0x034, reset 0x0000.0012 (see page 949) RXIFLSEL TXIFLSEL UARTIM, type R/W, offset 0x038, reset 0x0000.0000 (see page 951) LME5IM LME1IM LMSBIM 9BITIM OEIM BEIM PEIM FEIM RTIM TXIM 1462 RXIM DSRIM DCDIM CTSIM RIIM November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 BERIS PERIS FERIS RTRIS TXRIS RXRIS DSRRIS DCDRIS CTSRIS RIRIS PEMIS FEMIS RTMIS TXMIS RXMIS DSRMIS DCDMIS CTSMIS RIMIS PEIC FEIC RTIC TXIC RXIC DSRMIC DCDMIC CTSMIC RIMIC UARTRIS, type RO, offset 0x03C, reset 0x0000.000F (see page 955) LME5RIS LME1RIS LMSBRIS 9BITRIS OERIS UARTMIS, type RO, offset 0x040, reset 0x0000.0000 (see page 959) LME5MIS LME1MIS LMSBMIS 9BITMIS OEMIS BEMIS UARTICR, type W1C, offset 0x044, reset 0x0000.0000 (see page 963) LME5IC LME1IC LMSBIC 9BITIC OEIC BEIC UARTDMACTL, type R/W, offset 0x048, reset 0x0000.0000 (see page 965) DMAERR TXDMAE RXDMAE UARTLCTL, type R/W, offset 0x090, reset 0x0000.0000 (see page 966) BLEN MASTER UARTLSS, type RO, offset 0x094, reset 0x0000.0000 (see page 967) TSS UARTLTIM, type RO, offset 0x098, reset 0x0000.0000 (see page 968) TIMER UART9BITADDR, type R/W, offset 0x0A4, reset 0x0000.0000 (see page 969) 9BITEN ADDR UART9BITAMASK, type R/W, offset 0x0A8, reset 0x0000.00FF (see page 970) RANGE MASK UARTPP, type RO, offset 0xFC0, reset 0x0000.0003 (see page 971) NB SC UARTCC, type R/W, offset 0xFC8, reset 0x0000.0000 (see page 972) CS UARTPeriphID4, type RO, offset 0xFD0, reset 0x0000.0000 (see page 973) PID4 UARTPeriphID5, type RO, offset 0xFD4, reset 0x0000.0000 (see page 974) PID5 UARTPeriphID6, type RO, offset 0xFD8, reset 0x0000.0000 (see page 975) PID6 UARTPeriphID7, type RO, offset 0xFDC, reset 0x0000.0000 (see page 976) PID7 UARTPeriphID0, type RO, offset 0xFE0, reset 0x0000.0060 (see page 977) PID0 UARTPeriphID1, type RO, offset 0xFE4, reset 0x0000.0000 (see page 978) PID1 November 08, 2011 1463 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 UARTPeriphID2, type RO, offset 0xFE8, reset 0x0000.0018 (see page 979) PID2 UARTPeriphID3, type RO, offset 0xFEC, reset 0x0000.0001 (see page 980) PID3 UARTPCellID0, type RO, offset 0xFF0, reset 0x0000.000D (see page 981) CID0 UARTPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 (see page 982) CID1 UARTPCellID2, type RO, offset 0xFF8, reset 0x0000.0005 (see page 983) CID2 UARTPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 (see page 984) CID3 Synchronous Serial Interface (SSI) SSI0 base: 0x4000.8000 SSI1 base: 0x4000.9000 SSI2 base: 0x4000.A000 SSI3 base: 0x4000.B000 SSICR0, type R/W, offset 0x000, reset 0x0000.0000 (see page 1000) SCR SPH SPO FRF DSS SSICR1, type R/W, offset 0x004, reset 0x0000.0000 (see page 1002) EOT SOD MS SSE LBM BSY RFF RNE TNF TFE TXIM RXIM RTIM RORIM TXRIS RXRIS RTRIS RORRIS TXMIS RXMIS RTMIS RORMIS RTIC RORIC SSIDR, type R/W, offset 0x008, reset 0x0000.0000 (see page 1004) DATA SSISR, type RO, offset 0x00C, reset 0x0000.0003 (see page 1005) SSICPSR, type R/W, offset 0x010, reset 0x0000.0000 (see page 1007) CPSDVSR SSIIM, type R/W, offset 0x014, reset 0x0000.0000 (see page 1008) SSIRIS, type RO, offset 0x018, reset 0x0000.0008 (see page 1009) SSIMIS, type RO, offset 0x01C, reset 0x0000.0000 (see page 1011) SSIICR, type W1C, offset 0x020, reset 0x0000.0000 (see page 1013) SSIDMACTL, type R/W, offset 0x024, reset 0x0000.0000 (see page 1014) TXDMAE RXDMAE 1464 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 SSICC, type R/W, offset 0xFC8, reset 0x0000.0000 (see page 1015) CS SSIPeriphID4, type RO, offset 0xFD0, reset 0x0000.0000 (see page 1016) PID4 SSIPeriphID5, type RO, offset 0xFD4, reset 0x0000.0000 (see page 1017) PID5 SSIPeriphID6, type RO, offset 0xFD8, reset 0x0000.0000 (see page 1018) PID6 SSIPeriphID7, type RO, offset 0xFDC, reset 0x0000.0000 (see page 1019) PID7 SSIPeriphID0, type RO, offset 0xFE0, reset 0x0000.0022 (see page 1020) PID0 SSIPeriphID1, type RO, offset 0xFE4, reset 0x0000.0000 (see page 1021) PID1 SSIPeriphID2, type RO, offset 0xFE8, reset 0x0000.0018 (see page 1022) PID2 SSIPeriphID3, type RO, offset 0xFEC, reset 0x0000.0001 (see page 1023) PID3 SSIPCellID0, type RO, offset 0xFF0, reset 0x0000.000D (see page 1024) CID0 SSIPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 (see page 1025) CID1 SSIPCellID2, type RO, offset 0xFF8, reset 0x0000.0005 (see page 1026) CID2 SSIPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 (see page 1027) CID3 Inter-Integrated Circuit (I2C) Interface I2C Master I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 I2CMSA, type R/W, offset 0x000, reset 0x0000.0000 SA R/S I2CMCS, type RO, offset 0x004, reset 0x0000.0020 (Read-Only Status Register) CLKTO BUSBSY IDLE November 08, 2011 ARBLST DATACK ADRACK ERROR BUSY 1465 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 HS ACK STOP START RUN CLKIM IM CLKRIS RIS CLKMIS MIS CLKIC IC I2CMCS, type WO, offset 0x004, reset 0x0000.0020 (Write-Only Control Register) I2CMDR, type R/W, offset 0x008, reset 0x0000.0000 DATA I2CMTPR, type R/W, offset 0x00C, reset 0x0000.0001 HS TPR I2CMIMR, type R/W, offset 0x010, reset 0x0000.0000 I2CMRIS, type RO, offset 0x014, reset 0x0000.0000 I2CMMIS, type RO, offset 0x018, reset 0x0000.0000 I2CMICR, type WO, offset 0x01C, reset 0x0000.0000 I2CMCR, type R/W, offset 0x020, reset 0x0000.0000 SFE MFE LPBK I2CMCLKOCNT, type R/W, offset 0x024, reset 0x0000.0000 CNTL I2CMBMON, type RO, offset 0x02C, reset 0x0000.0000 Inter-Integrated Circuit (I2C) SDA SCL TREQ RREQ Interface I2C Slave I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 I2CSOAR, type R/W, offset 0x800, reset 0x0000.0000 OAR I2CSCSR, type RO, offset 0x804, reset 0x0000.0000 (Read-Only Status Register) OAR2SEL FBR I2CSCSR, type WO, offset 0x804, reset 0x0000.0000 (Write-Only Control Register) DA I2CSDR, type R/W, offset 0x808, reset 0x0000.0000 DATA I2CSIMR, type R/W, offset 0x80C, reset 0x0000.0000 STOPIM 1466 STARTIM DATAIM November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 I2CSRIS, type RO, offset 0x810, reset 0x0000.0000 STOPRIS STARTRIS DATARIS I2CSMIS, type RO, offset 0x814, reset 0x0000.0000 STOPMIS STARTMIS DATAMIS I2CSICR, type WO, offset 0x818, reset 0x0000.0000 STOPIC STARTIC DATAIC I2CSOAR2, type R/W, offset 0x81C, reset 0x0000.0000 OAR2EN OAR2 I2CSACKCTL, type R/W, offset 0x820, reset 0x0000.0000 ACKOVAL ACKOEN Inter-Integrated Circuit (I2C) Interface I2C Status and Control I2C 0 base: 0x4002.0000 I2C 1 base: 0x4002.1000 I2C 2 base: 0x4002.2000 I2C 3 base: 0x4002.3000 I2C 4 base: 0x400C.0000 I2C 5 base: 0x400C.1000 I2CPP, type RO, offset 0xFC0, reset 0x0000.0001 HS I2CPC, type RO, offset 0xFC4, reset 0x0000.0000 HS Controller Area Network (CAN) Module CAN0 base: 0x4004.0000 CAN1 base: 0x4004.1000 CANCTL, type R/W, offset 0x000, reset 0x0000.0001 (see page 1095) TEST CCE DAR BOFF EWARN EPASS EIE SIE IE INIT CANSTS, type R/W, offset 0x004, reset 0x0000.0000 (see page 1097) RXOK TXOK LEC CANERR, type RO, offset 0x008, reset 0x0000.0000 (see page 1100) RP REC TEC CANBIT, type R/W, offset 0x00C, reset 0x0000.2301 (see page 1101) TSEG2 TSEG1 SJW BRP CANINT, type RO, offset 0x010, reset 0x0000.0000 (see page 1102) INTID CANTST, type R/W, offset 0x014, reset 0x0000.0000 (see page 1103) RX TX LBACK SILENT BASIC CANBRPE, type R/W, offset 0x018, reset 0x0000.0000 (see page 1105) BRPE November 08, 2011 1467 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DATAA DATAB DATAA DATAB CANIF1CRQ, type R/W, offset 0x020, reset 0x0000.0001 (see page 1106) BUSY MNUM CANIF2CRQ, type R/W, offset 0x080, reset 0x0000.0001 (see page 1106) BUSY MNUM CANIF1CMSK, type R/W, offset 0x024, reset 0x0000.0000 (see page 1107) WRNRD MASK ARB CONTROL CLRINTPND WRNRD MASK ARB CONTROL CLRINTPND NEWDAT / TXRQST CANIF2CMSK, type R/W, offset 0x084, reset 0x0000.0000 (see page 1107) NEWDAT / TXRQST CANIF1MSK1, type R/W, offset 0x028, reset 0x0000.FFFF (see page 1110) MSK CANIF2MSK1, type R/W, offset 0x088, reset 0x0000.FFFF (see page 1110) MSK CANIF1MSK2, type R/W, offset 0x02C, reset 0x0000.FFFF (see page 1111) MXTD MDIR MSK CANIF2MSK2, type R/W, offset 0x08C, reset 0x0000.FFFF (see page 1111) MXTD MDIR MSK CANIF1ARB1, type R/W, offset 0x030, reset 0x0000.0000 (see page 1113) ID CANIF2ARB1, type R/W, offset 0x090, reset 0x0000.0000 (see page 1113) ID CANIF1ARB2, type R/W, offset 0x034, reset 0x0000.0000 (see page 1114) MSGVAL XTD DIR ID CANIF2ARB2, type R/W, offset 0x094, reset 0x0000.0000 (see page 1114) MSGVAL XTD DIR ID CANIF1MCTL, type R/W, offset 0x038, reset 0x0000.0000 (see page 1116) NEWDAT MSGLST INTPND UMASK TXIE RXIE RMTEN TXRQST EOB DLC TXRQST EOB DLC CANIF2MCTL, type R/W, offset 0x098, reset 0x0000.0000 (see page 1116) NEWDAT MSGLST INTPND UMASK TXIE RXIE RMTEN CANIF1DA1, type R/W, offset 0x03C, reset 0x0000.0000 (see page 1119) DATA CANIF1DA2, type R/W, offset 0x040, reset 0x0000.0000 (see page 1119) DATA CANIF1DB1, type R/W, offset 0x044, reset 0x0000.0000 (see page 1119) DATA 1468 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CANIF1DB2, type R/W, offset 0x048, reset 0x0000.0000 (see page 1119) DATA CANIF2DA1, type R/W, offset 0x09C, reset 0x0000.0000 (see page 1119) DATA CANIF2DA2, type R/W, offset 0x0A0, reset 0x0000.0000 (see page 1119) DATA CANIF2DB1, type R/W, offset 0x0A4, reset 0x0000.0000 (see page 1119) DATA CANIF2DB2, type R/W, offset 0x0A8, reset 0x0000.0000 (see page 1119) DATA CANTXRQ1, type RO, offset 0x100, reset 0x0000.0000 (see page 1120) TXRQST CANTXRQ2, type RO, offset 0x104, reset 0x0000.0000 (see page 1120) TXRQST CANNWDA1, type RO, offset 0x120, reset 0x0000.0000 (see page 1121) NEWDAT CANNWDA2, type RO, offset 0x124, reset 0x0000.0000 (see page 1121) NEWDAT CANMSG1INT, type RO, offset 0x140, reset 0x0000.0000 (see page 1122) INTPND CANMSG2INT, type RO, offset 0x144, reset 0x0000.0000 (see page 1122) INTPND CANMSG1VAL, type RO, offset 0x160, reset 0x0000.0000 (see page 1123) MSGVAL CANMSG2VAL, type RO, offset 0x164, reset 0x0000.0000 (see page 1123) MSGVAL Universal Serial Bus (USB) Controller Base 0x4005.0000 USBFADDR, type R/W, offset 0x000, reset 0x00 (see page 1146) FUNCADDR USBPOWER, type R/W, offset 0x001, reset 0x20 (OTG A / Host Mode) (see page 1147) RESET RESUME SUSPEND PWRDNPHY RESET RESUME SUSPEND PWRDNPHY USBPOWER, type R/W, offset 0x001, reset 0x20 (OTG B / Device Mode) (see page 1147) ISOUP SOFTCONN EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP7 EP6 EP5 EP4 EP3 EP2 EP1 USBTXIS, type RO, offset 0x002, reset 0x0000 (see page 1150) EP0 USBRXIS, type RO, offset 0x004, reset 0x0000 (see page 1152) November 08, 2011 1469 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 DISCON CONN SOF BABBLE RESUME SOF RESET SOF BABBLE RESUME SOF RESET USBTXIE, type R/W, offset 0x006, reset 0xFFFF (see page 1153) USBRXIE, type R/W, offset 0x008, reset 0xFFFE (see page 1155) USBIS, type RO, offset 0x00A, reset 0x00 (OTG A / Host Mode) (see page 1156) VBUSERR SESREQ USBIS, type RO, offset 0x00A, reset 0x00 (OTG B / Device Mode) (see page 1156) DISCON RESUME SUSPEND USBIE, type R/W, offset 0x00B, reset 0x06 (OTG A / Host Mode) (see page 1159) VBUSERR SESREQ DISCON CONN USBIE, type R/W, offset 0x00B, reset 0x06 (OTG B / Device Mode) (see page 1159) DISCON RESUME SUSPEND USBFRAME, type RO, offset 0x00C, reset 0x0000 (see page 1162) FRAME USBEPIDX, type R/W, offset 0x00E, reset 0x00 (see page 1163) EPIDX USBTEST, type R/W, offset 0x00F, reset 0x00 (OTG A / Host Mode) (see page 1164) FORCEH FIFOACC FORCEFS USBTEST, type R/W, offset 0x00F, reset 0x00 (OTG B / Device Mode) (see page 1164) FIFOACC FORCEFS USBFIFO0, type R/W, offset 0x020, reset 0x0000.0000 (see page 1166) EPDATA EPDATA USBFIFO1, type R/W, offset 0x024, reset 0x0000.0000 (see page 1166) EPDATA EPDATA USBFIFO2, type R/W, offset 0x028, reset 0x0000.0000 (see page 1166) EPDATA EPDATA USBFIFO3, type R/W, offset 0x02C, reset 0x0000.0000 (see page 1166) EPDATA EPDATA USBFIFO4, type R/W, offset 0x030, reset 0x0000.0000 (see page 1166) EPDATA EPDATA USBFIFO5, type R/W, offset 0x034, reset 0x0000.0000 (see page 1166) EPDATA EPDATA USBFIFO6, type R/W, offset 0x038, reset 0x0000.0000 (see page 1166) EPDATA EPDATA USBFIFO7, type R/W, offset 0x03C, reset 0x0000.0000 (see page 1166) EPDATA EPDATA USBDEVCTL, type R/W, offset 0x060, reset 0x80 (see page 1167) DEV FSDEV LSDEV VBUS HOST HOSTREQ SESSION USBTXFIFOSZ, type R/W, offset 0x062, reset 0x00 (see page 1169) DPB SIZE DPB SIZE USBRXFIFOSZ, type R/W, offset 0x063, reset 0x00 (see page 1169) USBTXFIFOADD, type R/W, offset 0x064, reset 0x0000 (see page 1170) ADDR 1470 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 USBRXFIFOADD, type R/W, offset 0x066, reset 0x0000 (see page 1170) ADDR USBCONTIM, type R/W, offset 0x07A, reset 0x5C (see page 1171) WTCON WTID USBVPLEN, type R/W, offset 0x07B, reset 0x3C (see page 1172) VPLEN USBFSEOF, type R/W, offset 0x07D, reset 0x77 (see page 1173) FSEOFG USBLSEOF, type R/W, offset 0x07E, reset 0x72 (see page 1174) LSEOFG USBTXFUNCADDR0, type R/W, offset 0x080, reset 0x00 (see page 1175) ADDR USBTXFUNCADDR1, type R/W, offset 0x088, reset 0x00 (see page 1175) ADDR USBTXFUNCADDR2, type R/W, offset 0x090, reset 0x00 (see page 1175) ADDR USBTXFUNCADDR3, type R/W, offset 0x098, reset 0x00 (see page 1175) ADDR USBTXFUNCADDR4, type R/W, offset 0x0A0, reset 0x00 (see page 1175) ADDR USBTXFUNCADDR5, type R/W, offset 0x0A8, reset 0x00 (see page 1175) ADDR USBTXFUNCADDR6, type R/W, offset 0x0B0, reset 0x00 (see page 1175) ADDR USBTXFUNCADDR7, type R/W, offset 0x0B8, reset 0x00 (see page 1175) ADDR USBTXHUBADDR0, type R/W, offset 0x082, reset 0x00 (see page 1176) ADDR USBTXHUBADDR1, type R/W, offset 0x08A, reset 0x00 (see page 1176) ADDR USBTXHUBADDR2, type R/W, offset 0x092, reset 0x00 (see page 1176) ADDR USBTXHUBADDR3, type R/W, offset 0x09A, reset 0x00 (see page 1176) ADDR USBTXHUBADDR4, type R/W, offset 0x0A2, reset 0x00 (see page 1176) ADDR USBTXHUBADDR5, type R/W, offset 0x0AA, reset 0x00 (see page 1176) ADDR USBTXHUBADDR6, type R/W, offset 0x0B2, reset 0x00 (see page 1176) ADDR USBTXHUBADDR7, type R/W, offset 0x0BA, reset 0x00 (see page 1176) ADDR USBTXHUBPORT0, type R/W, offset 0x083, reset 0x00 (see page 1177) PORT USBTXHUBPORT1, type R/W, offset 0x08B, reset 0x00 (see page 1177) PORT USBTXHUBPORT2, type R/W, offset 0x093, reset 0x00 (see page 1177) PORT USBTXHUBPORT3, type R/W, offset 0x09B, reset 0x00 (see page 1177) PORT USBTXHUBPORT4, type R/W, offset 0x0A3, reset 0x00 (see page 1177) PORT November 08, 2011 1471 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 USBTXHUBPORT5, type R/W, offset 0x0AB, reset 0x00 (see page 1177) PORT USBTXHUBPORT6, type R/W, offset 0x0B3, reset 0x00 (see page 1177) PORT USBTXHUBPORT7, type R/W, offset 0x0BB, reset 0x00 (see page 1177) PORT USBRXFUNCADDR1, type R/W, offset 0x08C, reset 0x00 (see page 1178) ADDR USBRXFUNCADDR2, type R/W, offset 0x094, reset 0x00 (see page 1178) ADDR USBRXFUNCADDR3, type R/W, offset 0x09C, reset 0x00 (see page 1178) ADDR USBRXFUNCADDR4, type R/W, offset 0x0A4, reset 0x00 (see page 1178) ADDR USBRXFUNCADDR5, type R/W, offset 0x0AC, reset 0x00 (see page 1178) ADDR USBRXFUNCADDR6, type R/W, offset 0x0B4, reset 0x00 (see page 1178) ADDR USBRXFUNCADDR7, type R/W, offset 0x0BC, reset 0x00 (see page 1178) ADDR USBRXHUBADDR1, type R/W, offset 0x08E, reset 0x00 (see page 1179) ADDR USBRXHUBADDR2, type R/W, offset 0x096, reset 0x00 (see page 1179) ADDR USBRXHUBADDR3, type R/W, offset 0x09E, reset 0x00 (see page 1179) ADDR USBRXHUBADDR4, type R/W, offset 0x0A6, reset 0x00 (see page 1179) ADDR USBRXHUBADDR5, type R/W, offset 0x0AE, reset 0x00 (see page 1179) ADDR USBRXHUBADDR6, type R/W, offset 0x0B6, reset 0x00 (see page 1179) ADDR USBRXHUBADDR7, type R/W, offset 0x0BE, reset 0x00 (see page 1179) ADDR USBRXHUBPORT1, type R/W, offset 0x08F, reset 0x00 (see page 1180) PORT USBRXHUBPORT2, type R/W, offset 0x097, reset 0x00 (see page 1180) PORT USBRXHUBPORT3, type R/W, offset 0x09F, reset 0x00 (see page 1180) PORT USBRXHUBPORT4, type R/W, offset 0x0A7, reset 0x00 (see page 1180) PORT USBRXHUBPORT5, type R/W, offset 0x0AF, reset 0x00 (see page 1180) PORT USBRXHUBPORT6, type R/W, offset 0x0B7, reset 0x00 (see page 1180) PORT USBRXHUBPORT7, type R/W, offset 0x0BF, reset 0x00 (see page 1180) PORT USBTXMAXP1, type R/W, offset 0x110, reset 0x0000 (see page 1181) MAXLOAD USBTXMAXP2, type R/W, offset 0x120, reset 0x0000 (see page 1181) MAXLOAD 1472 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ERROR SETUP STALLED TXRDY RXRDY SETEND DATAEND STALLED TXRDY RXRDY DT FLUSH USBTXMAXP3, type R/W, offset 0x130, reset 0x0000 (see page 1181) MAXLOAD USBTXMAXP4, type R/W, offset 0x140, reset 0x0000 (see page 1181) MAXLOAD USBTXMAXP5, type R/W, offset 0x150, reset 0x0000 (see page 1181) MAXLOAD USBTXMAXP6, type R/W, offset 0x160, reset 0x0000 (see page 1181) MAXLOAD USBTXMAXP7, type R/W, offset 0x170, reset 0x0000 (see page 1181) MAXLOAD USBCSRL0, type W1C, offset 0x102, reset 0x00 (OTG A / Host Mode) (see page 1182) NAKTO STATUS REQPKT USBCSRL0, type W1C, offset 0x102, reset 0x00 (OTG B / Device Mode) (see page 1182) SETENDC RXRDYC STALL USBCSRH0, type W1C, offset 0x103, reset 0x00 (OTG A / Host Mode) (see page 1186) DTWE USBCSRH0, type W1C, offset 0x103, reset 0x00 (OTG B / Device Mode) (see page 1186) FLUSH USBCOUNT0, type RO, offset 0x108, reset 0x00 (see page 1188) COUNT USBTYPE0, type R/W, offset 0x10A, reset 0x00 (see page 1189) SPEED USBNAKLMT, type R/W, offset 0x10B, reset 0x00 (see page 1190) NAKLMT USBTXCSRL1, type R/W, offset 0x112, reset 0x00 (OTG A / Host Mode) (see page 1191) NAKTO CLRDT STALLED SETUP FLUSH ERROR FIFONE TXRDY NAKTO CLRDT STALLED SETUP FLUSH ERROR FIFONE TXRDY NAKTO CLRDT STALLED SETUP FLUSH ERROR FIFONE TXRDY NAKTO CLRDT STALLED SETUP FLUSH ERROR FIFONE TXRDY NAKTO CLRDT STALLED SETUP FLUSH ERROR FIFONE TXRDY NAKTO CLRDT STALLED SETUP FLUSH ERROR FIFONE TXRDY NAKTO CLRDT STALLED SETUP FLUSH ERROR FIFONE TXRDY CLRDT STALLED STALL FLUSH UNDRN FIFONE TXRDY CLRDT STALLED STALL FLUSH UNDRN FIFONE TXRDY CLRDT STALLED STALL FLUSH UNDRN FIFONE TXRDY CLRDT STALLED STALL FLUSH UNDRN FIFONE TXRDY CLRDT STALLED STALL FLUSH UNDRN FIFONE TXRDY CLRDT STALLED STALL FLUSH UNDRN FIFONE TXRDY CLRDT STALLED STALL FLUSH UNDRN FIFONE TXRDY USBTXCSRL2, type R/W, offset 0x122, reset 0x00 (OTG A / Host Mode) (see page 1191) USBTXCSRL3, type R/W, offset 0x132, reset 0x00 (OTG A / Host Mode) (see page 1191) USBTXCSRL4, type R/W, offset 0x142, reset 0x00 (OTG A / Host Mode) (see page 1191) USBTXCSRL5, type R/W, offset 0x152, reset 0x00 (OTG A / Host Mode) (see page 1191) USBTXCSRL6, type R/W, offset 0x162, reset 0x00 (OTG A / Host Mode) (see page 1191) USBTXCSRL7, type R/W, offset 0x172, reset 0x00 (OTG A / Host Mode) (see page 1191) USBTXCSRL1, type R/W, offset 0x112, reset 0x00 (OTG B / Device Mode) (see page 1191) USBTXCSRL2, type R/W, offset 0x122, reset 0x00 (OTG B / Device Mode) (see page 1191) USBTXCSRL3, type R/W, offset 0x132, reset 0x00 (OTG B / Device Mode) (see page 1191) USBTXCSRL4, type R/W, offset 0x142, reset 0x00 (OTG B / Device Mode) (see page 1191) USBTXCSRL5, type R/W, offset 0x152, reset 0x00 (OTG B / Device Mode) (see page 1191) USBTXCSRL6, type R/W, offset 0x162, reset 0x00 (OTG B / Device Mode) (see page 1191) USBTXCSRL7, type R/W, offset 0x172, reset 0x00 (OTG B / Device Mode) (see page 1191) November 08, 2011 1473 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 MODE DMAEN FDT DMAMOD DTWE DT MODE DMAEN FDT DMAMOD DTWE DT MODE DMAEN FDT DMAMOD DTWE DT MODE DMAEN FDT DMAMOD DTWE DT MODE DMAEN FDT DMAMOD DTWE DT MODE DMAEN FDT DMAMOD DTWE DT MODE DMAEN FDT DMAMOD DTWE DT ISO MODE DMAEN FDT DMAMOD ISO MODE DMAEN FDT DMAMOD ISO MODE DMAEN FDT DMAMOD ISO MODE DMAEN FDT DMAMOD ISO MODE DMAEN FDT DMAMOD ISO MODE DMAEN FDT DMAMOD ISO MODE DMAEN FDT DMAMOD ERROR FULL RXRDY ERROR FULL RXRDY ERROR FULL RXRDY USBTXCSRH1, type R/W, offset 0x113, reset 0x00 (OTG A / Host Mode) (see page 1195) AUTOSET USBTXCSRH2, type R/W, offset 0x123, reset 0x00 (OTG A / Host Mode) (see page 1195) AUTOSET USBTXCSRH3, type R/W, offset 0x133, reset 0x00 (OTG A / Host Mode) (see page 1195) AUTOSET USBTXCSRH4, type R/W, offset 0x143, reset 0x00 (OTG A / Host Mode) (see page 1195) AUTOSET USBTXCSRH5, type R/W, offset 0x153, reset 0x00 (OTG A / Host Mode) (see page 1195) AUTOSET USBTXCSRH6, type R/W, offset 0x163, reset 0x00 (OTG A / Host Mode) (see page 1195) AUTOSET USBTXCSRH7, type R/W, offset 0x173, reset 0x00 (OTG A / Host Mode) (see page 1195) AUTOSET USBTXCSRH1, type R/W, offset 0x113, reset 0x00 (OTG B / Device Mode) (see page 1195) AUTOSET USBTXCSRH2, type R/W, offset 0x123, reset 0x00 (OTG B / Device Mode) (see page 1195) AUTOSET USBTXCSRH3, type R/W, offset 0x133, reset 0x00 (OTG B / Device Mode) (see page 1195) AUTOSET USBTXCSRH4, type R/W, offset 0x143, reset 0x00 (OTG B / Device Mode) (see page 1195) AUTOSET USBTXCSRH5, type R/W, offset 0x153, reset 0x00 (OTG B / Device Mode) (see page 1195) AUTOSET USBTXCSRH6, type R/W, offset 0x163, reset 0x00 (OTG B / Device Mode) (see page 1195) AUTOSET USBTXCSRH7, type R/W, offset 0x173, reset 0x00 (OTG B / Device Mode) (see page 1195) AUTOSET USBRXMAXP1, type R/W, offset 0x114, reset 0x0000 (see page 1199) MAXLOAD USBRXMAXP2, type R/W, offset 0x124, reset 0x0000 (see page 1199) MAXLOAD USBRXMAXP3, type R/W, offset 0x134, reset 0x0000 (see page 1199) MAXLOAD USBRXMAXP4, type R/W, offset 0x144, reset 0x0000 (see page 1199) MAXLOAD USBRXMAXP5, type R/W, offset 0x154, reset 0x0000 (see page 1199) MAXLOAD USBRXMAXP6, type R/W, offset 0x164, reset 0x0000 (see page 1199) MAXLOAD USBRXMAXP7, type R/W, offset 0x174, reset 0x0000 (see page 1199) MAXLOAD USBRXCSRL1, type R/W, offset 0x116, reset 0x00 (OTG A / Host Mode) (see page 1200) CLRDT STALLED REQPKT FLUSH CLRDT STALLED REQPKT FLUSH CLRDT STALLED REQPKT FLUSH DATAERR / NAKTO USBRXCSRL2, type R/W, offset 0x126, reset 0x00 (OTG A / Host Mode) (see page 1200) DATAERR / NAKTO USBRXCSRL3, type R/W, offset 0x136, reset 0x00 (OTG A / Host Mode) (see page 1200) 1474 DATAERR / NAKTO November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ERROR FULL RXRDY ERROR FULL RXRDY ERROR FULL RXRDY ERROR FULL RXRDY USBRXCSRL4, type R/W, offset 0x146, reset 0x00 (OTG A / Host Mode) (see page 1200) DATAERR / CLRDT STALLED REQPKT FLUSH CLRDT STALLED REQPKT FLUSH CLRDT STALLED REQPKT FLUSH CLRDT STALLED REQPKT FLUSH STALLED STALL FLUSH DATAERR OVER FULL RXRDY STALLED STALL FLUSH DATAERR OVER FULL RXRDY STALLED STALL FLUSH DATAERR OVER FULL RXRDY STALLED STALL FLUSH DATAERR OVER FULL RXRDY STALLED STALL FLUSH DATAERR OVER FULL RXRDY STALLED STALL FLUSH DATAERR OVER FULL RXRDY STALLED STALL FLUSH DATAERR OVER FULL RXRDY DMAEN PIDERR DMAMOD DTWE DT DMAEN PIDERR DMAMOD DTWE DT DMAEN PIDERR DMAMOD DTWE DT DMAEN PIDERR DMAMOD DTWE DT DMAEN PIDERR DMAMOD DTWE DT DMAEN PIDERR DMAMOD DTWE DT DMAEN PIDERR DMAMOD DTWE DT NAKTO USBRXCSRL5, type R/W, offset 0x156, reset 0x00 (OTG A / Host Mode) (see page 1200) DATAERR / NAKTO USBRXCSRL6, type R/W, offset 0x166, reset 0x00 (OTG A / Host Mode) (see page 1200) DATAERR / NAKTO USBRXCSRL7, type R/W, offset 0x176, reset 0x00 (OTG A / Host Mode) (see page 1200) DATAERR / NAKTO USBRXCSRL1, type R/W, offset 0x116, reset 0x00 (OTG B / Device Mode) (see page 1200) CLRDT USBRXCSRL2, type R/W, offset 0x126, reset 0x00 (OTG B / Device Mode) (see page 1200) CLRDT USBRXCSRL3, type R/W, offset 0x136, reset 0x00 (OTG B / Device Mode) (see page 1200) CLRDT USBRXCSRL4, type R/W, offset 0x146, reset 0x00 (OTG B / Device Mode) (see page 1200) CLRDT USBRXCSRL5, type R/W, offset 0x156, reset 0x00 (OTG B / Device Mode) (see page 1200) CLRDT USBRXCSRL6, type R/W, offset 0x166, reset 0x00 (OTG B / Device Mode) (see page 1200) CLRDT USBRXCSRL7, type R/W, offset 0x176, reset 0x00 (OTG B / Device Mode) (see page 1200) CLRDT USBRXCSRH1, type R/W, offset 0x117, reset 0x00 (OTG A / Host Mode) (see page 1205) AUTOCL AUTORQ USBRXCSRH2, type R/W, offset 0x127, reset 0x00 (OTG A / Host Mode) (see page 1205) AUTOCL AUTORQ USBRXCSRH3, type R/W, offset 0x137, reset 0x00 (OTG A / Host Mode) (see page 1205) AUTOCL AUTORQ USBRXCSRH4, type R/W, offset 0x147, reset 0x00 (OTG A / Host Mode) (see page 1205) AUTOCL AUTORQ USBRXCSRH5, type R/W, offset 0x157, reset 0x00 (OTG A / Host Mode) (see page 1205) AUTOCL AUTORQ USBRXCSRH6, type R/W, offset 0x167, reset 0x00 (OTG A / Host Mode) (see page 1205) AUTOCL AUTORQ USBRXCSRH7, type R/W, offset 0x177, reset 0x00 (OTG A / Host Mode) (see page 1205) AUTOCL AUTORQ USBRXCSRH1, type R/W, offset 0x117, reset 0x00 (OTG B / Device Mode) (see page 1205) AUTOCL ISO DMAEN ISO DMAEN ISO DMAEN ISO DMAEN ISO DMAEN DISNYET / PIDERR DMAMOD USBRXCSRH2, type R/W, offset 0x127, reset 0x00 (OTG B / Device Mode) (see page 1205) AUTOCL DISNYET / PIDERR DMAMOD USBRXCSRH3, type R/W, offset 0x137, reset 0x00 (OTG B / Device Mode) (see page 1205) AUTOCL DISNYET / PIDERR DMAMOD USBRXCSRH4, type R/W, offset 0x147, reset 0x00 (OTG B / Device Mode) (see page 1205) AUTOCL DISNYET / PIDERR DMAMOD USBRXCSRH5, type R/W, offset 0x157, reset 0x00 (OTG B / Device Mode) (see page 1205) AUTOCL November 08, 2011 DISNYET / PIDERR DMAMOD 1475 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 AUTOCL ISO DMAEN ISO DMAEN USBRXCSRH6, type R/W, offset 0x167, reset 0x00 (OTG B / Device Mode) (see page 1205) DISNYET / PIDERR DMAMOD USBRXCSRH7, type R/W, offset 0x177, reset 0x00 (OTG B / Device Mode) (see page 1205) AUTOCL DISNYET / PIDERR DMAMOD USBRXCOUNT1, type RO, offset 0x118, reset 0x0000 (see page 1209) COUNT USBRXCOUNT2, type RO, offset 0x128, reset 0x0000 (see page 1209) COUNT USBRXCOUNT3, type RO, offset 0x138, reset 0x0000 (see page 1209) COUNT USBRXCOUNT4, type RO, offset 0x148, reset 0x0000 (see page 1209) COUNT USBRXCOUNT5, type RO, offset 0x158, reset 0x0000 (see page 1209) COUNT USBRXCOUNT6, type RO, offset 0x168, reset 0x0000 (see page 1209) COUNT USBRXCOUNT7, type RO, offset 0x178, reset 0x0000 (see page 1209) COUNT USBTXTYPE1, type R/W, offset 0x11A, reset 0x00 (see page 1210) SPEED PROTO TEP SPEED PROTO TEP SPEED PROTO TEP SPEED PROTO TEP SPEED PROTO TEP SPEED PROTO TEP SPEED PROTO TEP USBTXTYPE2, type R/W, offset 0x12A, reset 0x00 (see page 1210) USBTXTYPE3, type R/W, offset 0x13A, reset 0x00 (see page 1210) USBTXTYPE4, type R/W, offset 0x14A, reset 0x00 (see page 1210) USBTXTYPE5, type R/W, offset 0x15A, reset 0x00 (see page 1210) USBTXTYPE6, type R/W, offset 0x16A, reset 0x00 (see page 1210) USBTXTYPE7, type R/W, offset 0x17A, reset 0x00 (see page 1210) USBTXINTERVAL1, type R/W, offset 0x11B, reset 0x00 (see page 1212) TXPOLL / NAKLMT USBTXINTERVAL2, type R/W, offset 0x12B, reset 0x00 (see page 1212) TXPOLL / NAKLMT USBTXINTERVAL3, type R/W, offset 0x13B, reset 0x00 (see page 1212) TXPOLL / NAKLMT USBTXINTERVAL4, type R/W, offset 0x14B, reset 0x00 (see page 1212) TXPOLL / NAKLMT USBTXINTERVAL5, type R/W, offset 0x15B, reset 0x00 (see page 1212) TXPOLL / NAKLMT USBTXINTERVAL6, type R/W, offset 0x16B, reset 0x00 (see page 1212) TXPOLL / NAKLMT USBTXINTERVAL7, type R/W, offset 0x17B, reset 0x00 (see page 1212) TXPOLL / NAKLMT USBRXTYPE1, type R/W, offset 0x11C, reset 0x00 (see page 1213) SPEED PROTO TEP SPEED PROTO TEP USBRXTYPE2, type R/W, offset 0x12C, reset 0x00 (see page 1213) 1476 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 USBRXTYPE3, type R/W, offset 0x13C, reset 0x00 (see page 1213) SPEED PROTO TEP SPEED PROTO TEP SPEED PROTO TEP SPEED PROTO TEP SPEED PROTO TEP USBRXTYPE4, type R/W, offset 0x14C, reset 0x00 (see page 1213) USBRXTYPE5, type R/W, offset 0x15C, reset 0x00 (see page 1213) USBRXTYPE6, type R/W, offset 0x16C, reset 0x00 (see page 1213) USBRXTYPE7, type R/W, offset 0x17C, reset 0x00 (see page 1213) USBRXINTERVAL1, type R/W, offset 0x11D, reset 0x00 (see page 1215) TXPOLL / NAKLMT USBRXINTERVAL2, type R/W, offset 0x12D, reset 0x00 (see page 1215) TXPOLL / NAKLMT USBRXINTERVAL3, type R/W, offset 0x13D, reset 0x00 (see page 1215) TXPOLL / NAKLMT USBRXINTERVAL4, type R/W, offset 0x14D, reset 0x00 (see page 1215) TXPOLL / NAKLMT USBRXINTERVAL5, type R/W, offset 0x15D, reset 0x00 (see page 1215) TXPOLL / NAKLMT USBRXINTERVAL6, type R/W, offset 0x16D, reset 0x00 (see page 1215) TXPOLL / NAKLMT USBRXINTERVAL7, type R/W, offset 0x17D, reset 0x00 (see page 1215) TXPOLL / NAKLMT USBRQPKTCOUNT1, type R/W, offset 0x304, reset 0x0000 (see page 1216) COUNT USBRQPKTCOUNT2, type R/W, offset 0x308, reset 0x0000 (see page 1216) COUNT USBRQPKTCOUNT3, type R/W, offset 0x30C, reset 0x0000 (see page 1216) COUNT USBRQPKTCOUNT4, type R/W, offset 0x310, reset 0x0000 (see page 1216) COUNT USBRQPKTCOUNT5, type R/W, offset 0x314, reset 0x0000 (see page 1216) COUNT USBRQPKTCOUNT6, type R/W, offset 0x318, reset 0x0000 (see page 1216) COUNT USBRQPKTCOUNT7, type R/W, offset 0x31C, reset 0x0000 (see page 1216) COUNT USBRXDPKTBUFDIS, type R/W, offset 0x340, reset 0x0000 (see page 1217) EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP7 EP6 EP5 EP4 EP3 EP2 EP1 USBTXDPKTBUFDIS, type R/W, offset 0x342, reset 0x0000 (see page 1218) USBEPC, type R/W, offset 0x400, reset 0x0000.0000 (see page 1219) PFLTACT PFLTAEN PFLTSEN PFLTEN EPENDE EPEN USBEPCRIS, type RO, offset 0x404, reset 0x0000.0000 (see page 1222) PF USBEPCIM, type R/W, offset 0x408, reset 0x0000.0000 (see page 1223) PF November 08, 2011 1477 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 USBEPCISC, type R/W, offset 0x40C, reset 0x0000.0000 (see page 1224) PF USBDRRIS, type RO, offset 0x410, reset 0x0000.0000 (see page 1225) RESUME USBDRIM, type R/W, offset 0x414, reset 0x0000.0000 (see page 1226) RESUME USBDRISC, type W1C, offset 0x418, reset 0x0000.0000 (see page 1227) RESUME USBGPCS, type R/W, offset 0x41C, reset 0x0000.0003 (see page 1228) DEVMODOTG DEVMOD USBVDC, type R/W, offset 0x430, reset 0x0000.0000 (see page 1229) VBDEN USBVDCRIS, type RO, offset 0x434, reset 0x0000.0000 (see page 1230) VD USBVDCIM, type R/W, offset 0x438, reset 0x0000.0000 (see page 1231) VD USBVDCISC, type R/W, offset 0x43C, reset 0x0000.0000 (see page 1232) VD USBIDVRIS, type RO, offset 0x444, reset 0x0000.0000 (see page 1233) ID USBIDVIM, type R/W, offset 0x448, reset 0x0000.0000 (see page 1234) ID USBIDVISC, type R/W1C, offset 0x44C, reset 0x0000.0000 (see page 1235) ID USBDMASEL, type R/W, offset 0x450, reset 0x0033.2211 (see page 1236) DMABTX DMABRX DMACTX DMACRX DMAATX DMAARX USBPP, type RO, offset 0xFC0, reset 0x0000.08D0 (see page 1238) ECNT USB PHY TYPE Analog Comparators Base 0x4003.C000 ACMIS, type R/W1C, offset 0x000, reset 0x0000.0000 (see page 1245) IN2 IN1 IN0 IN2 IN1 IN0 IN2 IN1 IN0 ACRIS, type RO, offset 0x004, reset 0x0000.0000 (see page 1246) ACINTEN, type R/W, offset 0x008, reset 0x0000.0000 (see page 1247) 1478 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ACREFCTL, type R/W, offset 0x010, reset 0x0000.0000 (see page 1248) EN RNG VREF ACSTAT0, type RO, offset 0x020, reset 0x0000.0000 (see page 1249) OVAL ACSTAT1, type RO, offset 0x040, reset 0x0000.0000 (see page 1249) OVAL ACSTAT2, type RO, offset 0x060, reset 0x0000.0000 (see page 1249) OVAL ACCTL0, type R/W, offset 0x024, reset 0x0000.0000 (see page 1250) TOEN ASRCP TSLVAL TSEN ISLVAL ISEN CINV TSLVAL TSEN ISLVAL ISEN CINV TSLVAL TSEN ISLVAL ISEN CINV ACCTL1, type R/W, offset 0x044, reset 0x0000.0000 (see page 1250) TOEN ASRCP ACCTL2, type R/W, offset 0x064, reset 0x0000.0000 (see page 1250) TOEN ASRCP ACMPPP, type RO, offset 0xFC0, reset 0x0007.0007 (see page 1252) C2O C1O C0O CMP2 CMP1 CMP0 Pulse Width Modulator (PWM) PWM0 base: 0x4002.8000 PWM1 base: 0x4002.9000 PWMCTL, type R/W, offset 0x000, reset 0x0000.0000 (see page 1269) GLOBALSYNC3 GLOBALSYNC2 GLOBALSYNC1 GLOBALSYNC0 PWMSYNC, type R/W, offset 0x004, reset 0x0000.0000 (see page 1271) SYNC3 SYNC2 SYNC1 SYNC0 PWMENABLE, type R/W, offset 0x008, reset 0x0000.0000 (see page 1272) PWM7EN PWM6EN PWM5EN PWM4EN PWM3EN PWM2EN PWM1EN PWM0EN PWMINVERT, type R/W, offset 0x00C, reset 0x0000.0000 (see page 1274) PWM7INV PWM6INV PWM5INV PWM4INV PWM3INV PWM2INV PWM1INV PWM0INV PWMFAULT, type R/W, offset 0x010, reset 0x0000.0000 (see page 1276) FAULT7 FAULT6 FAULT5 FAULT4 FAULT3 FAULT2 FAULT1 FAULT0 PWMINTEN, type R/W, offset 0x014, reset 0x0000.0000 (see page 1278) INTFAULT3 INTFAULT2 INTFAULT1 INTFAULT0 INTPWM3 INTPWM2 INTPWM1 INTPWM0 PWMRIS, type RO, offset 0x018, reset 0x0000.0000 (see page 1280) INTFAULT3 INTFAULT2 INTFAULT1 INTFAULT0 INTPWM3 INTPWM2 INTPWM1 INTPWM0 PWMISC, type R/W1C, offset 0x01C, reset 0x0000.0000 (see page 1283) INTFAULT3 INTFAULT2 INTFAULT1 INTFAULT0 INTPWM3 INTPWM2 INTPWM1 INTPWM0 November 08, 2011 1479 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 FAULT3 FAULT2 FAULT1 FAULT0 PWM3 PWM2 PWM1 PWM0 PWMSTATUS, type RO, offset 0x020, reset 0x0000.0000 (see page 1286) PWMFAULTVAL, type R/W, offset 0x024, reset 0x0000.0000 (see page 1288) PWM7 PWM6 PWM5 PWM4 PWMENUPD, type R/W, offset 0x028, reset 0x0000.0000 (see page 1290) ENUPD7 ENUPD6 ENUPD5 ENUPD4 ENUPD3 ENUPD2 ENUPD1 ENUPD0 LATCH MINFLTPER FLTSRC GENBUPD GENAUPD CMPBUPD CMPAUPD LOADUPD DEBUG MODE ENABLE LATCH MINFLTPER FLTSRC GENAUPD CMPBUPD CMPAUPD LOADUPD DEBUG MODE ENABLE LATCH MINFLTPER FLTSRC GENAUPD CMPBUPD CMPAUPD LOADUPD DEBUG MODE ENABLE LATCH MINFLTPER FLTSRC GENAUPD CMPBUPD CMPAUPD LOADUPD DEBUG MODE ENABLE PWM0CTL, type R/W, offset 0x040, reset 0x0000.0000 (see page 1294) DBFALLUPD DBRISEUPD DBCTLUPD PWM1CTL, type R/W, offset 0x080, reset 0x0000.0000 (see page 1294) DBFALLUPD DBRISEUPD DBCTLUPD GENBUPD PWM2CTL, type R/W, offset 0x0C0, reset 0x0000.0000 (see page 1294) DBFALLUPD DBRISEUPD DBCTLUPD GENBUPD PWM3CTL, type R/W, offset 0x100, reset 0x0000.0000 (see page 1294) DBFALLUPD DBRISEUPD DBCTLUPD GENBUPD PWM0INTEN, type R/W, offset 0x044, reset 0x0000.0000 (see page 1299) TRCMPBD TRCMPBU TRCMPAD TRCMPAU TRCNTLOAD TRCNTZERO INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM1INTEN, type R/W, offset 0x084, reset 0x0000.0000 (see page 1299) TRCMPBD TRCMPBU TRCMPAD TRCMPAU TRCNTLOAD TRCNTZERO INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM2INTEN, type R/W, offset 0x0C4, reset 0x0000.0000 (see page 1299) TRCMPBD TRCMPBU TRCMPAD TRCMPAU TRCNTLOAD TRCNTZERO INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM3INTEN, type R/W, offset 0x104, reset 0x0000.0000 (see page 1299) TRCMPBD TRCMPBU TRCMPAD TRCMPAU TRCNTLOAD TRCNTZERO INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM0RIS, type RO, offset 0x048, reset 0x0000.0000 (see page 1302) INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM1RIS, type RO, offset 0x088, reset 0x0000.0000 (see page 1302) INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM2RIS, type RO, offset 0x0C8, reset 0x0000.0000 (see page 1302) INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM3RIS, type RO, offset 0x108, reset 0x0000.0000 (see page 1302) INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM0ISC, type R/W1C, offset 0x04C, reset 0x0000.0000 (see page 1304) INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM1ISC, type R/W1C, offset 0x08C, reset 0x0000.0000 (see page 1304) INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO 1480 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PWM2ISC, type R/W1C, offset 0x0CC, reset 0x0000.0000 (see page 1304) INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM3ISC, type R/W1C, offset 0x10C, reset 0x0000.0000 (see page 1304) INTCMPBD INTCMPBU INTCMPAD INTCMPAU INTCNTLOAD INTCNTZERO PWM0LOAD, type R/W, offset 0x050, reset 0x0000.0000 (see page 1306) LOAD PWM1LOAD, type R/W, offset 0x090, reset 0x0000.0000 (see page 1306) LOAD PWM2LOAD, type R/W, offset 0x0D0, reset 0x0000.0000 (see page 1306) LOAD PWM3LOAD, type R/W, offset 0x110, reset 0x0000.0000 (see page 1306) LOAD PWM0COUNT, type RO, offset 0x054, reset 0x0000.0000 (see page 1307) COUNT PWM1COUNT, type RO, offset 0x094, reset 0x0000.0000 (see page 1307) COUNT PWM2COUNT, type RO, offset 0x0D4, reset 0x0000.0000 (see page 1307) COUNT PWM3COUNT, type RO, offset 0x114, reset 0x0000.0000 (see page 1307) COUNT PWM0CMPA, type R/W, offset 0x058, reset 0x0000.0000 (see page 1308) COMPA PWM1CMPA, type R/W, offset 0x098, reset 0x0000.0000 (see page 1308) COMPA PWM2CMPA, type R/W, offset 0x0D8, reset 0x0000.0000 (see page 1308) COMPA PWM3CMPA, type R/W, offset 0x118, reset 0x0000.0000 (see page 1308) COMPA PWM0CMPB, type R/W, offset 0x05C, reset 0x0000.0000 (see page 1309) COMPB PWM1CMPB, type R/W, offset 0x09C, reset 0x0000.0000 (see page 1309) COMPB PWM2CMPB, type R/W, offset 0x0DC, reset 0x0000.0000 (see page 1309) COMPB November 08, 2011 1481 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PWM3CMPB, type R/W, offset 0x11C, reset 0x0000.0000 (see page 1309) COMPB PWM0GENA, type R/W, offset 0x060, reset 0x0000.0000 (see page 1310) ACTCMPBD ACTCMPBU ACTCMPAD ACTCMPAU ACTLOAD ACTZERO ACTCMPAD ACTCMPAU ACTLOAD ACTZERO ACTCMPAD ACTCMPAU ACTLOAD ACTZERO ACTCMPAD ACTCMPAU ACTLOAD ACTZERO ACTCMPAD ACTCMPAU ACTLOAD ACTZERO ACTCMPAD ACTCMPAU ACTLOAD ACTZERO ACTCMPAD ACTCMPAU ACTLOAD ACTZERO ACTCMPAD ACTCMPAU ACTLOAD ACTZERO PWM1GENA, type R/W, offset 0x0A0, reset 0x0000.0000 (see page 1310) ACTCMPBD ACTCMPBU PWM2GENA, type R/W, offset 0x0E0, reset 0x0000.0000 (see page 1310) ACTCMPBD ACTCMPBU PWM3GENA, type R/W, offset 0x120, reset 0x0000.0000 (see page 1310) ACTCMPBD ACTCMPBU PWM0GENB, type R/W, offset 0x064, reset 0x0000.0000 (see page 1313) ACTCMPBD ACTCMPBU PWM1GENB, type R/W, offset 0x0A4, reset 0x0000.0000 (see page 1313) ACTCMPBD ACTCMPBU PWM2GENB, type R/W, offset 0x0E4, reset 0x0000.0000 (see page 1313) ACTCMPBD ACTCMPBU PWM3GENB, type R/W, offset 0x124, reset 0x0000.0000 (see page 1313) ACTCMPBD ACTCMPBU PWM0DBCTL, type R/W, offset 0x068, reset 0x0000.0000 (see page 1316) ENABLE PWM1DBCTL, type R/W, offset 0x0A8, reset 0x0000.0000 (see page 1316) ENABLE PWM2DBCTL, type R/W, offset 0x0E8, reset 0x0000.0000 (see page 1316) ENABLE PWM3DBCTL, type R/W, offset 0x128, reset 0x0000.0000 (see page 1316) ENABLE PWM0DBRISE, type R/W, offset 0x06C, reset 0x0000.0000 (see page 1317) RISEDELAY PWM1DBRISE, type R/W, offset 0x0AC, reset 0x0000.0000 (see page 1317) RISEDELAY PWM2DBRISE, type R/W, offset 0x0EC, reset 0x0000.0000 (see page 1317) RISEDELAY PWM3DBRISE, type R/W, offset 0x12C, reset 0x0000.0000 (see page 1317) RISEDELAY 1482 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 PWM0DBFALL, type R/W, offset 0x070, reset 0x0000.0000 (see page 1318) FALLDELAY PWM1DBFALL, type R/W, offset 0x0B0, reset 0x0000.0000 (see page 1318) FALLDELAY PWM2DBFALL, type R/W, offset 0x0F0, reset 0x0000.0000 (see page 1318) FALLDELAY PWM3DBFALL, type R/W, offset 0x130, reset 0x0000.0000 (see page 1318) FALLDELAY PWM0FLTSRC0, type R/W, offset 0x074, reset 0x0000.0000 (see page 1319) PWM1FLTSRC0, type R/W, offset 0x0B4, reset 0x0000.0000 (see page 1319) PWM2FLTSRC0, type R/W, offset 0x0F4, reset 0x0000.0000 (see page 1319) PWM3FLTSRC0, type R/W, offset 0x134, reset 0x0000.0000 (see page 1319) PWM0FLTSRC1, type R/W, offset 0x078, reset 0x0000.0000 (see page 1321) DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 FAULT3 FAULT2 FAULT1 FAULT0 PWM1FLTSRC1, type R/W, offset 0x0B8, reset 0x0000.0000 (see page 1321) PWM2FLTSRC1, type R/W, offset 0x0F8, reset 0x0000.0000 (see page 1321) PWM3FLTSRC1, type R/W, offset 0x138, reset 0x0000.0000 (see page 1321) PWM0MINFLTPER, type R/W, offset 0x07C, reset 0x0000.0000 (see page 1324) MFP PWM1MINFLTPER, type R/W, offset 0x0BC, reset 0x0000.0000 (see page 1324) MFP PWM2MINFLTPER, type R/W, offset 0x0FC, reset 0x0000.0000 (see page 1324) MFP PWM3MINFLTPER, type R/W, offset 0x13C, reset 0x0000.0000 (see page 1324) MFP PWM0FLTSEN, type R/W, offset 0x800, reset 0x0000.0000 (see page 1325) November 08, 2011 1483 Texas Instruments-Advance Information Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 FAULT3 FAULT2 FAULT1 FAULT0 PWM1FLTSEN, type R/W, offset 0x880, reset 0x0000.0000 (see page 1325) PWM2FLTSEN, type R/W, offset 0x900, reset 0x0000.0000 (see page 1325) PWM3FLTSEN, type R/W, offset 0x980, reset 0x0000.0000 (see page 1325) PWM0FLTSTAT0, type -, offset 0x804, reset 0x0000.0000 (see page 1326) PWM1FLTSTAT0, type -, offset 0x884, reset 0x0000.0000 (see page 1326) PWM2FLTSTAT0, type -, offset 0x904, reset 0x0000.0000 (see page 1326) PWM3FLTSTAT0, type -, offset 0x984, reset 0x0000.0000 (see page 1326) PWM0FLTSTAT1, type -, offset 0x808, reset 0x0000.0000 (see page 1328) DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 DCMP7 DCMP6 DCMP5 DCMP4 DCMP3 DCMP2 DCMP1 DCMP0 PWM1FLTSTAT1, type -, offset 0x888, reset 0x0000.0000 (see page 1328) PWM2FLTSTAT1, type -, offset 0x908, reset 0x0000.0000 (see page 1328) PWM3FLTSTAT1, type -, offset 0x988, reset 0x0000.0000 (see page 1328) PWMPP, type RO, offset 0xFC0, reset 0x0000.0344 (see page 1331) ONE EFAULT ESYNC FCNT GCNT PWMPC, type R/W, offset 0xFC4, reset 0x0000.0000 (see page 1333) PWMDIV USEPWMDIV Quadrature Encoder Interface (QEI) QEI0 base: 0x4002.C000 QEI1 base: 0x4002.D000 QEICTL, type R/W, offset 0x000, reset 0x0000.0000 (see page 1340) FILTCNT FILTEN STALLEN INVI INVB INVA VELDIV VELEN RESMODE CAPMODE SIGMODE SWAP ENABLE DIRECTION ERROR QEISTAT, type RO, offset 0x004, reset 0x0000.0000 (see page 1343) QEIPOS, type R/W, offset 0x008, reset 0x0000.0000 (see page 1344) POSITION POSITION 1484 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 INTERROR INTDIR INTTIMER INTINDEX INTERROR INTDIR INTTIMER INTINDEX INTERROR INTDIR INTTIMER INTINDEX QEIMAXPOS, type R/W, offset 0x00C, reset 0x0000.0000 (see page 1345) MAXPOS MAXPOS QEILOAD, type R/W, offset 0x010, reset 0x0000.0000 (see page 1346) LOAD LOAD QEITIME, type RO, offset 0x014, reset 0x0000.0000 (see page 1347) TIME TIME QEICOUNT, type RO, offset 0x018, reset 0x0000.0000 (see page 1348) COUNT COUNT QEISPEED, type RO, offset 0x01C, reset 0x0000.0000 (see page 1349) SPEED SPEED QEIINTEN, type R/W, offset 0x020, reset 0x0000.0000 (see page 1350) QEIRIS, type RO, offset 0x024, reset 0x0000.0000 (see page 1352) QEIISC, type R/W1C, offset 0x028, reset 0x0000.0000 (see page 1354) November 08, 2011 1485 Texas Instruments-Advance Information Ordering and Contact Information B Ordering and Contact Information B.1 Ordering Information LM CCNNN XY PPS I GR Core 4F = ARM® Cortex™-M4F Shipping Medium R = Tape-and-reel Omitted = Default shipping (tray or tube) Part Number NNN = Series part number Internal Use Only Flash Size H = 256 KB Temperature I = –40°C to +85°C SRAM Size 5 = 32 KB Speed C = 40 MHz Package BB = 157-ball BGA Table B-1. Part Ordering Information B.2 Orderable Part Number Description LM4F232H5BBFIG Stellaris LM4F232H5BB Microcontroller Industrial Temperature 157-ball BGA LM4F232H5BBFIGR Stellaris LM4F232H5BB Microcontroller Industrial Temperature 157-ball BGA Tape-and-reel ® Part Markings The Stellaris microcontrollers are marked with an identifying number. This code contains the following information: ■ The first and second lines indicate the part number. For example, LM4F232H5QDFIGA0. The second letter in the part number indicates the product status. An M indicates the part is fully qualified and released to production. An X, for example, LX4F232H5QDFIGA0, indicates the part is experimental and requires a waiver ■ The third line contains internal tracking numbers. B.3 Kits The Stellaris Family provides the hardware and software tools that engineers need to begin development quickly. ■ Reference Design Kits accelerate product development by providing ready-to-run hardware and comprehensive documentation including hardware design files ■ Evaluation Kits provide a low-cost and effective means of evaluating Stellaris microcontrollers before purchase ■ Development Kits provide you with all the tools you need to develop and prototype embedded applications right out of the box See the website at www.ti.com/stellaris for the latest tools available, or ask your distributor. 1486 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller B.4 Support Information For support on Stellaris products, contact the TI Worldwide Product Information Center nearest you: http://www-k.ext.ti.com/sc/technical-support/product-information-centers.htm. November 08, 2011 1487 Texas Instruments-Advance Information Package Information C Package Information C.1 157-Ball BGA Package C.1.1 Package Dimensions Note: The center is depopulated on the 157-ball BGA package. 1488 November 08, 2011 Texas Instruments-Advance Information ® Stellaris LM4F232H5BB Microcontroller Figure C-1. Stellaris LM4F232H5BB 157-Ball BGA Package Dimensions November 08, 2011 1489 Texas Instruments-Advance Information PACKAGE OPTION ADDENDUM www.ti.com 25-Jan-2012 PACKAGING INFORMATION Orderable Device LM4F232H5BB Status (1) PREVIEW Package Type Package Drawing XCEPT BGA Pins Package Qty Eco Plan 157 TBD (2) Lead/ Ball Finish Call TI MSL Peak Temp (3) Samples (Requires Login) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated