LM675T/LF02

LM675 www.ti.com SNOSBP3E – MAY 1999 – REVISED MARCH 2013 LM675 Power Operational Amplifier Check for Samples: LM675 FEATURES 1 • • • • • • • • 2 • • • • • 3A Current Capability AVO Typically 90 dB 5.5 MHz Gain Bandwidth Product 8 V/μs Slew Rate Wide Power Bandwidth 70 kHz 1 mV Typical Offset Voltage Short Circuit Protection Thermal Protection with Parole Circuit (100% Tested) 16V–60V Supply Range Wide Common Mode Range Internal Output Protection Diodes 90 dB Ripple Rejection Plastic Power Package TO-220 Connection Diagram *The tab is internally connected to pin 3 (−VEE) Figure 1. Front View TO-220 Power Package (NDH) See Package Number NDH0005D Typical Applications APPLICATIONS • • • • • High Performance Power Op Amp Bridge Amplifiers Motor Speed Controls Servo Amplifiers Instrument Systems DESCRIPTION The LM675 is a monolithic power operational amplifier featuring wide bandwidth and low input offset voltage, making it equally suitable for AC and DC applications. The LM675 is capable of delivering output currents in excess of 3 amps, operating at supply voltages of up to 60V. The device overload protection consists of both internal current limiting and thermal shutdown. The amplifier is also internally compensated for gains of 10 or greater. Figure 2. Non-Inverting Amplifier 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1999–2013, Texas Instruments Incorporated LM675 SNOSBP3E – MAY 1999 – REVISED MARCH 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS (1) (2) Supply Voltage ±30V −VEE to VCC Input Voltage Operating Temperature 0°C to +70°C Storage Temperature −65°C to +150°C Junction Temperature 150°C Power Dissipation (3) 30W Lead Temperature (Soldering, 10 seconds) 260°C ESD rating to be determined. (1) (2) (3) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. Assumes TA equal to 70°C. For operation at higher tab temperatures, the LM675 must be derated based on a maximum junction temperature of 150°C. ELECTRICAL CHARACTERISTICS VS=±25V, TA=25°C unless otherwise specified. Parameter Conditions Typical Tested Limit Units 18 50 (max) mA VCM = 0V 1 10 (max) mV VCM = 0V 0.2 2 (max) μA Input Offset Current VCM = 0V 50 500 (max) nA Open Loop Gain RL = ∞Ω 90 70 (min) dB PSRR ΔVS = ±5V 90 70 (min) dB CMRR VIN = ±20V 90 70 (min) dB Output Voltage Swing RL = 8Ω ±21 ±18 (min) V Offset Voltage Drift Versus Temperature RS < 100 kΩ 25 Supply Current POUT = 0W Input Offset Voltage Input Bias Current Offset Voltage Drift Versus Output Power Output Power THD = 1%, fO = 1 kHz, RL = 8Ω 25 Gain Bandwidth Product fO = 20 kHz, AVCL = 1000 5.5 Max Slew Rate μV/W 20 ±22 Submit Documentation Feedback W MHz 8 Input Common Mode Range 2 μV/°C 25 V/μs ±20 (min) V Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 LM675 www.ti.com SNOSBP3E – MAY 1999 – REVISED MARCH 2013 TYPICAL APPLICATIONS VS = ±8V → ±30V Figure 3. Generating a Split Supply From a Single Supply Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 3 LM675 SNOSBP3E – MAY 1999 – REVISED MARCH 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS THD vs Power Output Input Common Mode Range vs Supply Voltage Figure 4. Figure 5. Supply Current vs Supply Voltage PSRR vs Frequency Figure 6. Figure 7. Device Dissipation vs Ambient Temperature† Current Limit vs Output Voltage* †θ INTERFACE = 1° C/W See APPLICATION HINTS. *VS = ±25V Figure 8. 4 Figure 9. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 LM675 www.ti.com SNOSBP3E – MAY 1999 – REVISED MARCH 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) IB vs Supply Voltage Output Voltage Swing vs Supply Voltage Figure 10. Figure 11. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 5 LM675 SNOSBP3E – MAY 1999 – REVISED MARCH 2013 www.ti.com SCHEMATIC DIAGRAM 6 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 LM675 www.ti.com SNOSBP3E – MAY 1999 – REVISED MARCH 2013 APPLICATION HINTS STABILITY The LM675 is designed to be stable when operated at a closed-loop gain of 10 or greater, but, as with any other high-current amplifier, the LM675 can be made to oscillate under certain conditions. These usually involve printed circuit board layout or output/input coupling. When designing a printed circuit board layout, it is important to return the load ground, the output compensation ground, and the low level (feedback and input) grounds to the circuit board ground point through separate paths. Otherwise, large currents flowing along a ground conductor will generate voltages on the conductor which can effectively act as signals at the input, resulting in high frequency oscillation or excessive distortion. It is advisable to keep the output compensation components and the 0.1 μF supply decoupling capacitors as close as possible to the LM675 to reduce the effects of PCB trace resistance and inductance. For the same reason, the ground return paths for these components should be as short as possible. Occasionally, current in the output leads (which function as antennas) can be coupled through the air to the amplifier input, resulting in high-frequency oscillation. This normally happens when the source impedance is high or the input leads are long. The problem can be eliminated by placing a small capacitor (on the order of 50 pF to 500 pF) across the circuit input. Most power amplifiers do not drive highly capacitive loads well, and the LM675 is no exception. If the output of the LM675 is connected directly to a capacitor with no series resistance, the square wave response will exhibit ringing if the capacitance is greater than about 0.1 μF. The amplifier can typically drive load capacitances up to 2 μF or so without oscillating, but this is not recommended. If highly capacitive loads are expected, a resistor (at least 1Ω) should be placed in series with the output of the LM675. A method commonly employed to protect amplifiers from low impedances at high frequencies is to couple to the load through a 10Ω resistor in parallel with a 5 μH inductor. CURRENT LIMIT AND SAFE OPERATING AREA (SOA) PROTECTION A power amplifier's output transistors can be damaged by excessive applied voltage, current flow, or power dissipation. The voltage applied to the amplifier is limited by the design of the external power supply, while the maximum current passed by the output devices is usually limited by internal circuitry to some fixed value. Shortterm power dissipation is usually not limited in monolithic operational power amplifiers, and this can be a problem when driving reactive loads, which may draw large currents while high voltages appear on the output transistors. The LM675 not only limits current to around 4A, but also reduces the value of the limit current when an output transistor has a high voltage across it. When driving nonlinear reactive loads such as motors or loudspeakers with built-in protection relays, there is a possibility that an amplifier output will be connected to a load whose terminal voltage may attempt to swing beyond the power supply voltages applied to the amplifier. This can cause degradation of the output transistors or catastrophic failure of the whole circuit. The standard protection for this type of failure mechanism is a pair of diodes connected between the output of the amplifier and the supply rails. These are part of the internal circuitry of the LM675, and needn't be added externally when standard reactive loads are driven. THERMAL PROTECTION The LM675 has a sophisticated thermal protection scheme to prevent long-term thermal stress to the device. When the temperature on the die reaches 170°C, the LM675 shuts down. It starts operating again when the die temperature drops to about 145°C, but if the temperature again begins to rise, shutdown will occur at only 150°C. Therefore, the device is allowed to heat up to a relatively high temperature if the fault condition is temporary, but a sustained fault will limit the maximum die temperature to a lower value. This greatly reduces the stresses imposed on the IC by thermal cycling, which in turn improves its reliability under sustained fault conditions. This circuitry is 100% tested without a heat sink. Since the die temperature is directly dependent upon the heat sink, the heat sink should be chosen for thermal resistance low enough that thermal shutdown will not be reached during normal operaton. Using the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of any power semiconductor. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 7 LM675 SNOSBP3E – MAY 1999 – REVISED MARCH 2013 www.ti.com POWER DISSIPATION AND HEAT SINKING The LM675 should always be operated with a heat sink, even though at idle worst case power dissipation will be only 1.8W (30 mA × 60V) which corresponds to a rise in die temperature of 97°C above ambient assuming θjA = 54°C/W for a TO-220 package. This in itself will not cause the thermal protection circuitry to shut down the amplifier when operating at room temperature, but a mere 0.9W of additional power dissipation will shut the amplifier down since TJ will then increase from 122°C (97°C + 25°C) to 170°C. In order to determine the appropriate heat sink for a given application, the power dissipation of the LM675 in that application must be known. When the load is resistive, the maximum average power that the IC will be required to dissipate is approximately: where • • • VS is the total power supply voltage across the LM675 RL is the load resistance PQ is the quiescent power dissipation of the amplifier The above equation is only an approximation which assumes an “ideal” class B output stage and constant power dissipation in all other parts of the circuit. As an example, if the LM675 is operated on a 50V power supply with a resistive load of 8Ω, it can develop up to 19W of internal power dissipation. If the die temperature is to remain below 150°C for ambient temperatures up to 70°C, the total junction-to-ambient thermal resistance must be less than Using θJC = 2°C/W, the sum of the case-to-heat sink interface thermal resistance and the heat-sink-to-ambient thermal resistance must be less than 2.2°C/W. The case-to-heat-sink thermal resistance of the TO-220 package varies with the mounting method used. A metal-to-metal interface will be about 1°C/W if lubricated, and about 1.2°C/W if dry. If a mica insulator is used, the thermal resistance will be about 1.6°C/W lubricated and 3.4°C/W dry. For this example, we assume a lubricated mica insulator between the LM675 and the heat sink. The heat sink thermal resistance must then be less than 4.2°C/W − 2°C/W − 1.6°C/W = 0.6°C/W. (1) This is a rather large heat sink and may not be practical in some applications. If a smaller heat sink is required for reasons of size or cost, there are two alternatives. The maximum ambient operating temperature can be restricted to 50°C (122°F), resulting in a 1.6°C/W heat sink, or the heat sink can be isolated from the chassis so the mica washer is not needed. This will change the required heat sink to a 1.2°C/W unit if the case-to-heat-sink interface is lubricated. The thermal requirements can become more difficult when an amplifier is driving a reactive load. For a given magnitude of load impedance, a higher degree of reactance will cause a higher level of power dissipation within the amplifier. As a general rule, the power dissipation of an amplifier driving a 60° reactive load will be roughly that of the same amplifier driving the resistive part of that load. For example, some reactive loads may at some frequency have an impedance with a magnitude of 8Ω and a phase angle of 60°. The real part of this load will then be 8Ω × cos 60° or 4Ω, and the amplifier power dissipation will roughly follow the curve of power dissipation with a 4Ω load. 8 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 LM675 www.ti.com SNOSBP3E – MAY 1999 – REVISED MARCH 2013 Typical Applications Figure 12. Non-Inverting Unity Gain Operation Figure 13. Inverting Unity Gain Operation Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 9 LM675 SNOSBP3E – MAY 1999 – REVISED MARCH 2013 www.ti.com Figure 14. Servo Motor Control IOUT = VIN × 2.5 amps/volt i.e. IOUT = 1A when VIN = 400 mV Trim pot for max ROUT Figure 15. High Current Source/Sink 10 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 LM675 www.ti.com SNOSBP3E – MAY 1999 – REVISED MARCH 2013 REVISION HISTORY Changes from Revision D (March 2013) to Revision E • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 10 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LM675 11 PACKAGE OPTION ADDENDUM www.ti.com 30-Sep-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) LM675T ACTIVE TO-220 NDH 5 45 Non-RoHS & Green Call TI Level-1-NA-UNLIM 0 to 70 LM675T LM675T/LF02 ACTIVE TO-220 NEB 5 45 RoHS & Green SN Level-1-NA-UNLIM 0 to 70 LM675T LM675T/LF05 ACTIVE TO-220 NEB 5 45 RoHS & Green SN Level-1-NA-UNLIM 0 to 70 LM675T LM675T/NOPB ACTIVE TO-220 NDH 5 45 RoHS & Green SN Level-1-NA-UNLIM 0 to 70 LM675T (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of