Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM8262
SNOS975G – MAY 2001 – REVISED AUGUST 2015
LM8262 Dual RRIO, High Output Current and Unlimited Cap Load Op Amp in VSSOP
1 Features
(VS = 5V, TA = 25°C, Typical Values Unless
Specified).
1
•
•
•
•
•
•
•
•
•
•
•
GBWP 21MHz
Wide Supply Voltage Range 2.5 V to 22 V
Slew Rate 12V/µs
Supply Current/channel 1.15 mA
Cap Load Limit Unlimited
Output Short Circuit Current +53mA/−75 mA
+/−5% Settling Time 400ns (500 pF, 100 mVPP
step)
Input Common Mode Voltage 0.3 V Beyond Rails
Input Voltage Noise 15nV/√Hz
Input Current Noise 1pA/√Hz
THD+N < 0.05%
2 Applications
•
•
•
•
TFT-LCD Flat Panel VCOM driver
A/D Converter Buffer
High Side/low Side Sensing
Headphone Amplifier
3 Description
The LM8262 is a Rail-to-Rail input and output Op
Amp which can operate with a wide supply voltage
range. This device has high output current drive,
greater than Rail-to-Rail input common mode voltage
range, unlimited capacitive load drive capability, and
provides tested and ensured high speed and slew
rate. It is specifically designed to handle the
requirements of flat panel TFT panel VCOM driver
applications as well as being suitable for other low
power and medium speed applications which require
ease of use and enhanced performance over existing
devices.
Greater than Rail-to-Rail input common mode voltage
range with 50 dB of Common Mode Rejection allows
high side and low side sensing for many applications
without concern for exceeding the range and with no
compromise in accuracy. In addition, most device
parameters are insensitive to power supply variations.
This design enhancement is yet another step in
simplifying its usage. The output stage has low
distortion (0.05% THD+N) and can supply a
respectable amount of current (15 mA) with minimal
headroom from either rail (300 mV).
The LM8262 is offered in the space saving VSSOP
package.
Device Information(1)
PART NUMBER
LM8262
PACKAGE
VSSOP (8)
BODY SIZE (NOM)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Gain/Phase vs. Frequency
Output Response with Heavy Capacitive Load
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM8262
SNOS975G – MAY 2001 – REVISED AUGUST 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
4
4
4
4
Absolute Maximum Ratings .....................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
6.5 2.7V Electrical Characteristics .................................
6.6 5V Electrical Characteristics ....................................
6.7 +/−11V Electrical Characteristics .............................
6.8 Typical Performance Characteristics ........................
7
Device and Documentation Support.................. 12
7.1
7.2
7.3
7.4
8
5
6
7
9
Community Resources............................................
Trademarks .............................................................
Electrostatic Discharge Caution ..............................
Glossary ..................................................................
12
12
12
12
Mechanical, Packaging, and Orderable
Information ........................................................... 12
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision F (August 2014) to Revision G
Page
•
Changed pin 5 From: -IN B To: +IN B Non-Inverting Input B in the Pin Functions table ....................................................... 3
•
Changed pin 6 From: +IN B To: -IN B Inverting Input B in the Pin Functions table............................................................... 3
•
Moved "Storage temperature range" to the Absolute Maximum Ratings
•
Changed Handling Ratings To: ESD Ratings ........................................................................................................................ 4
(1) (2)
Changes from Revision E (April 2013) to Revision F
....................................................................... 4
Page
•
Changed data sheet structure and organization. Added, updated, or renamed the following sections: Device and
Documentation Support; Mechanical, Packaging, and Ordering Information......................................................................... 1
•
Changed from "Junction Temperature Range" to "Operating Temperature Range".............................................................. 4
•
Deleted TJ = 25°C, ................................................................................................................................................................. 5
•
Deleted TJ = 25°C, ................................................................................................................................................................. 6
•
Deleted TJ = 25°C................................................................................................................................................................... 7
Changes from Revision D (April 2013) to Revision E
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 10
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
LM8262
www.ti.com
SNOS975G – MAY 2001 – REVISED AUGUST 2015
5 Pin Configuration and Functions
8-Pin
VSSOP
Top View
Pin Functions
PIN
I/O
DESCRIPTION
NUMBER
NAME
1
OUT A
O
Output A
2
-IN A
I
Inverting Input A
3
+IN A
I
Non-Inverting Input A
4
V-
I
Negative Supply
5
+IN B
I
Non-Inverting Input B
6
-IN B
I
Inverting Input B
7
OUT B
O
Output B
8
V+
I
Positive Supply
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
3
LM8262
SNOS975G – MAY 2001 – REVISED AUGUST 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
(1) (2)
over operating free-air temperature range (unless otherwise noted)
(3)
MIN
VIN Differential
Output Short Circuit Duration
MAX
UNIT
+/−10
V
(4) (5)
See
Supply Voltage (V+ - V−)
24
V
V+ +0.8, V− −0.8
V
+150
°C
+150
°C
Infrared or Convection (20 sec.)
235
°C
Wave Soldering (10 sec.)
260
°C
Voltage at Input/Output pins
Junction Temperature
(6)
−65
Storage temperature range, Tstg
Soldering Information:
(1)
(2)
(3)
(4)
(5)
(6)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Rating indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C.
Output short circuit duration is infinite for VS ≤ 6V at room temperature and below. For VS > 6V, allowable short circuit duration is 1.5ms.
The maximum power dissipation is a function of TJ(max), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/RθJA. All numbers apply for packages soldered directly onto a PC board.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
(3)
Electrostatic discharge (1)
Human Body Model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (2)
±2000
Machine Model (MM) (3)
±200
UNIT
V
Human Body Model, 1.5 kΩ in series with 100 pF. Machine Model, 0 Ω is series with 200 pF.
JEDEC document JEP155 states that 2000-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 200-V MM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Supply Voltage (V+ - V−)
Operating Temperature Range
(1)
(1)
MIN
MAX
2.5
22
UNIT
V
−40
+85
°C
The maximum power dissipation is a function of TJ(max), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/RθJA. All numbers apply for packages soldered directly onto a PC board.
6.4 Thermal Information
THERMAL METRIC (1)
RθJA
(1)
(2)
4
Junction-to-ambient thermal resistance (2)
DGK
8 PINS
235
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
The maximum power dissipation is a function of TJ(max),RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/RθJA. All numbers apply for packages soldered directly onto a PC board.
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
LM8262
www.ti.com
6.5
SNOS975G – MAY 2001 – REVISED AUGUST 2015
2.7V Electrical Characteristics
Unless otherwise specified, all limits ensured for V+ = 2.7V, V− = 0V, VCM = 0.5V, VO = V+/2, and RL > 1MΩ to V−. Boldface
limits apply at the temperature extremes.
PARAMETER
TEST CONDITIONS
MIN (1)
TYP (2)
MAX (1)
VOS
Input Offset Voltage
VCM = 0.5V & VCM = 2.2V
–
+/−0.7
+/−5
+/−7
TC VOS
Input Offset Average Drift
VCM = 0.5V & VCM = 2.2V
–
+/−2
–
IB
Input Bias Current
VCM = 0.5V
–
−1.20
−2.00
−2.70
VCM = 2.2V
–
+0.49
+1.00
+1.60
–
20
250
400
76
60
100
–
(3)
(4)
(4)
IOS
Input Offset Current
VCM = 0.5V & VCM = 2.2V
CMRR
Common Mode Rejection Ratio
VCM stepped from 0V to 1.0V
VCM stepped from 1.7V to 2.7V
–
100
–
VCM stepped from 0V to 2.7V
58
50
70
–
78
74
104
–
–
−0.3
−0.1
0.0
2.8
2.7
3.0
–
VO = 0.5 to 2.2V,
RL = 10k to V−
70
67
78
–
VO = 0.5 to 2.2V,
RL = 2k to V−
67
63
73
–
RL = 10k to V−
2.49
2.46
2.59
–
RL = 2k to V−
2.45
2.41
2.53
–
–
90
100
120
+PSRR
Positive Power Supply Rejection
Ratio
V+ = 2.7V to 5V
CMVR
Input Common-Mode Voltage
Range
CMRR > 50dB
AVOL
VO
Large Signal Voltage Gain
Output Swing
High
ISC
UNIT
mV
µV/C
µA
nA
dB
dB
V
V
dB
dB
V
Output Swing
Low
RL = 10k to V−
Output Short Circuit Current
Sourcing to V−
VID = 200mV (5) (6)
30
20
48
–
Sinking to V+
VID = −200mV
50
30
65
–
–
2.0
2.5
3.0
mA
–
9
–
V/µs
MHz
IS
Supply Current (both amps)
SR
Slew Rate
(7)
(5) (6)
No load, VCM = 0.5V
AV = +1,VI = 2VPP
+
mV
mA
fu
Unity Gain-Frequency
VI = 10mV, RL = 2kΩ to V /2
–
10
–
GBWP
Gain Bandwidth Product
f = 50KHz
15.5
14
21
–
Phim
Phase Margin
VI = 10mV
–
50
–
Deg
en
Input-Referred Voltage Noise
f = 2KHz, RS = 50Ω
–
15
–
nV/ √Hz
in
Input-Referred Current Noise
f = 2KHz
–
1
–
pA/ √Hz
–
1
–
MHz
fmax
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Full Power Bandwidth
+
ZL = (20pF || 10kΩ) to V /2
MHz
All limits are ensured by testing or statistical analysis.
Typical Values represent the most likely parametric norm.
Offset voltage average drift determined by dividing the change in VOS at temperature extremes into the total temperature change.
Positive current corresponds to current flowing into the device.
Short circuit test is a momentary test.
Output short circuit duration is infinite for VS ≤ 6V at room temperature and below. For VS > 6V, allowable short circuit duration is 1.5ms.
Slew rate is the slower of the rising and falling slew rates. Connected as a Voltage Follower.
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
5
LM8262
SNOS975G – MAY 2001 – REVISED AUGUST 2015
6.6
www.ti.com
5V Electrical Characteristics
Unless otherwise specified, all limits ensured for V+ = 5V, V− = 0V, VCM = 1V, VO = V+/2, and RL > 1MΩ to V−. Boldface limits
apply at the temperature extremes.
PARAMETER
TEST CONDITIONS
MIN (1)
TYP (2)
MAX (1)
VOS
Input Offset Voltage
VCM = 1V & VCM = 4.5V
–
+/−0.7
+/−5
+/− 7
TC VOS
Input Offset Average Drift
VCM = 1V & VCM = 4.5V
–
+/−2
–
IB
Input Bias Current
VCM = 1V
–
−1.18
−2.00
−2.70
VCM = 4.5V
–
+0.49
+1.00
+1.60
–
20
250
400
84
72
110
–
VCM stepped from 4V to 5V
–
100
–
VCM stepped from 0V to 5V
64
61
80
–
78
74
104
–
–
−0.3
−0.1
0.0
5.1
5.0
5.3
–
VO = 0.5 to 4.5V,
RL = 10k to V−
74
70
84
–
VO = 0.5 to 4.5V,
RL = 2k to V−
70
66
80
–
RL = 10k to V−
4.75
4.72
4.87
–
RL = 2k to V−
4.70
4.66
4.81
–
–
86
125
135
(3)
(4)
(4)
IOS
Input Offset Current
VCM = 1V & VCM = 4.5V
CMRR
Common Mode Rejection Ratio
VCM stepped from 0V to 3.3V
+PSRR
Positive Power Supply Rejection
Ratio
V+ = 2.7V to 5V, VCM = 0.5V
CMVR
Input Common-Mode Voltage
Range
CMRR > 50dB
AVOL
VO
Large Signal Voltage Gain
Output Swing
High
ISC
mV
µV/°C
µA
nA
dB
dB
V
V
dB
V
Output Swing
Low
RL = 10k to V−
Output Short Circuit Current
Sourcing to V−
VID = 200mV (5) (6)
35
20
53
–
Sinking to V+
VID = −200mV
60
50
75
–
No load, VCM = 1V
–
2.3
2.8
3.5
AV = +1, VI = 5VPP
10
7
12
–
–
10.5
–
(5) (6)
UNIT
mV
mA
IS
Supply Current (both amps)
SR
Slew Rate
fu
Unity Gain Frequency
VI = 10mV,
RL = 2kΩ to V+/2
GBWP
Gain-Bandwidth Product
f = 50KHz
16
15
21
–
Phim
Phase Margin
VI = 10mV
–
53
–
Deg
en
Input-Referred Voltage Noise
f = 2KHz, RS = 50Ω
–
15
–
nV/ √Hz
in
Input-Referred Current Noise
f = 2KHz
–
1
–
pA/ √Hz
(1)
(2)
(3)
(4)
(5)
(6)
(7)
6
(7)
mA
V/µs
MHz
MHz
All limits are ensured by testing or statistical analysis.
Typical Values represent the most likely parametric norm.
Offset voltage average drift determined by dividing the change in VOS at temperature extremes into the total temperature change.
Positive current corresponds to current flowing into the device.
Short circuit test is a momentary test.
Output short circuit duration is infinite for VS ≤ 6V at room temperature and below. For VS > 6V, allowable short circuit duration is 1.5ms.
Slew rate is the slower of the rising and falling slew rates. Connected as a Voltage Follower.
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
LM8262
www.ti.com
SNOS975G – MAY 2001 – REVISED AUGUST 2015
5V Electrical Characteristics (continued)
Unless otherwise specified, all limits ensured for V+ = 5V, V− = 0V, VCM = 1V, VO = V+/2, and RL > 1MΩ to V−. Boldface limits
apply at the temperature extremes.
PARAMETER
TEST CONDITIONS
MIN (1)
TYP (2)
MAX (1)
UNIT
fmax
Full Power Bandwidth
ZL = (20pF || 10kΩ) to V+/2
–
900
–
KHz
tS
Settling Time (+/−5%)
100mVPP Step, 500pF load
–
400
–
ns
THD+N
Total Harmonic Distortion + Noise
RL = 1kΩ to V+/2
f = 10KHz to AV= +2, 4VPP swing
–
0.05%
–
6.7
+/−11V Electrical Characteristics
Unless otherwise specified, all limits ensured for V+ = 11V, V− = −11V, VCM = 0V, VO = 0V, and RL > 1MΩ to 0V. Boldface
limits apply at the temperature extremes.
PARAMETER
TEST CONDITIONS
MIN (1)
TYP (2)
MAX (1)
VOS
Input Offset Voltage
VCM = −10.5V & VCM = 10.5V
–
+/−0.7
+/−7
+/− 9
TC VOS
Input Offset Average Drift
VCM = −10.5V & VCM = 10.5V
–
+/−2
–
IB
Input Bias Current
VCM = −10.5V
–
−1.05
−2.00
−2.80
VCM = 10.5V
–
+0.49
+1.00
+1.50
(3)
(4)
(4)
IOS
Input Offset Current
VCM = −10.5V & VCM = 10.5V
–
30
275
550
CMRR
Common Mode Rejection Ratio
VCM stepped from −11V to 9V
84
80
100
–
VCM stepped from 10V to 11V
–
100
–
VCM stepped from −11V to 11V
74
72
88
–
70
66
100
–
70
66
100
–
–
−11.3
−11.1
−11.0
11.1
11.0
11.3
–
VO = 0V to +/−9V,
RL = 10kΩ
78
74
85
–
VO = 0V to +/−9V,
RL = 2kΩ
72
66
79
–
RL = 10kΩ
10.65
10.61
10.77
–
RL = 2kΩ
10.6
10.55
10.69
–
RL = 10kΩ
–
−10.98
−10.75
−10.65
RL = 2kΩ
–
−10.91
−10.65
−10.6
+
+PSRR
Positive Power Supply Rejection
Ratio
−PSRR
Negative Power Supply Rejection V− = −9V to −11V
Ratio
CMVR
Input Common-Mode Voltage
Range
AVOL
VO
Large Signal Voltage Gain
Output Swing
High
Output Swing
Low
(1)
(2)
(3)
(4)
V = 9V to 11V
CMRR > 50dB
UNIT
mV
µV/°C
µA
nA
dB
dB
dB
V
V
dB
V
V
All limits are ensured by testing or statistical analysis.
Typical Values represent the most likely parametric norm.
Offset voltage average drift determined by dividing the change in VOS at temperature extremes into the total temperature change.
Positive current corresponds to current flowing into the device.
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
7
LM8262
SNOS975G – MAY 2001 – REVISED AUGUST 2015
www.ti.com
+/−11V Electrical Characteristics (continued)
Unless otherwise specified, all limits ensured for V+ = 11V, V− = −11V, VCM = 0V, VO = 0V, and RL > 1MΩ to 0V. Boldface
limits apply at the temperature extremes.
MIN (1)
TYP (2)
MAX (1)
Sourcing to ground
VID = 200mV (5) (6)
40
25
60
–
Sinking to ground
VID = 200mV (5) (6)
65
55
100
–
–
2.5
4
5
10
8
15
–
PARAMETER
ISC
Output Short Circuit Current
TEST CONDITIONS
UNIT
mA
IS
Supply Current
No load, VCM = 0V
SR
Slew Rate
AV = +1, VI = 16VPP
fU
Unity Gain Frequency
VI = 10mV, RL = 2kΩ
–
13
–
GBWP
Gain-Bandwidth Product
f = 50KHz
18
16
24
–
Phim
Phase Margin
VI = 10mV
–
58
–
Deg
en
Input-Referred Voltage Noise
f = 2KHz, RS = 50Ω
–
15
–
nV/ √Hz
in
Input-Referred Current Noise
f = 2KHz
–
1
–
pA/ √Hz
tS
Settling Time (+/−1%, AV = +1)
Positive Step, 5VPP
–
320
–
Negative Step, 5VPP
–
600
–
(7)
THD+N
Total Harmonic Distortion +Noise
RL = 1kΩ, f = 10KHz,
AV = +2, 15VPP swing
–
0.01%
–
CTREJ
Cross-Talk Rejection
f = 5MHz, Driver
RL = 10kΩ
–
68
–
(5)
(6)
(7)
8
mA
V/µs
MHz
MHz
ns
dB
Short circuit test is a momentary test.
Output short circuit duration is infinite for VS ≤ 6V at room temperature and below. For VS > 6V, allowable short circuit duration is 1.5ms.
Slew rate is the slower of the rising and falling slew rates. Connected as a Voltage Follower.
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
LM8262
www.ti.com
SNOS975G – MAY 2001 – REVISED AUGUST 2015
6.8 Typical Performance Characteristics
TA = 25°C, Unless Otherwise Noted
Figure 1. VOS vs. VCM for 3 Representative Units
Figure 2. VOS vs. VCM for 3 Representative Units
Figure 3. VOS vs. VCM for 3 Representative Units
Figure 4. VOS vs. VS for 3 Representative Units
Figure 5. VOS vs. VS for 3 Representative Units
Figure 6. VOS vs. VS for 3 Representative Units
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
9
LM8262
SNOS975G – MAY 2001 – REVISED AUGUST 2015
www.ti.com
Typical Performance Characteristics (continued)
TA = 25°C, Unless Otherwise Noted
10
Figure 7. IB vs. VCM
Figure 8. IB vs. VS
Figure 9. IS vs. VCM
Figure 10. IS vs. VCM
Figure 11. IS vs. VCM
Figure 12. IS vs. VS (PNP side)
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
LM8262
www.ti.com
SNOS975G – MAY 2001 – REVISED AUGUST 2015
Typical Performance Characteristics (continued)
TA = 25°C, Unless Otherwise Noted
Figure 13. IS vs. VS (NPN side)
Figure 14. Gain/Phase vs. Frequency
Figure 15. Unity Gain Frequency vs. VS
Figure 16. Phase Margin vs. VS
Figure 17. Unity Gain Freq. and Phase Margin vs. VS
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
11
LM8262
SNOS975G – MAY 2001 – REVISED AUGUST 2015
www.ti.com
7 Device and Documentation Support
7.1 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
7.2 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
7.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
7.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
8 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
12
Submit Documentation Feedback
Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM8262
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM8262MM
NRND
VSSOP
DGK
8
1000
Non-RoHS
& Green
Call TI
Level-1-260C-UNLIM
-40 to 85
A46
LM8262MM/NOPB
ACTIVE
VSSOP
DGK
8
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 85
A46
LM8262MMX/NOPB
ACTIVE
VSSOP
DGK
8
3500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 85
A46
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of