Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM8272
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
LM8272 Dual RRIO, High Output Current & Unlimited Cap Load
Op Amp in Miniature Package
1 Features
3 Description
(VS = 12V, TA = 25°C, Typical values unless
specified).
1
•
•
•
•
•
•
•
•
•
•
GBWP 15MHz
Wide supply voltage range 2.5 V to 24 V
Slew rate 15 V/µs
Supply current/channel 0.95 mA
Cap load tolerance Unlimited
Output short circuit current ±13 0mA
Output current (1 V from rails) ±65 mA
Input common mode voltage 0.3 V beyond rails
Input voltage noise 15 nV/√Hz
Input current noise 1.4 pA/√Hz
2 Applications
•
•
•
•
TFT-LCD flat panel VCOM driver
A/D converter buffer
High side/low side sensing
Headphone amplifier
The LM8272 is a Rail-to-Rail input and output Op
Amp which can operate with a wide supply voltage
range. This device has high output current drive,
greater than Rail-to-Rail input common mode voltage
range, and unlimited capacitive load drive capability,
while requiring only 0.95mA/channel supply current. It
is specifically designed to handle the requirements of
flat panel TFT panel VCOM driver applications as well
as being suitable for other low power and medium
speed applications which require ease of use and
enhanced performance over existing devices.
Greater than Rail-to-Rail input common mode voltage
range with 50 dB of Common Mode Rejection allows
high side and low side sensing among many
applications without concerns for exceeding the range
and with no compromise in accuracy. An
exceptionally wide operating supply voltage range of
2.5 V to 24 V removes any concerns over
functionality under extreme conditions and offers
flexibility of use in multitude of applications. In
addition, most device parameters are insensitive to
power supply variations. This design enhancement is
yet another step in simplifying its usage.
The LM8272 is offered in the 8-pin VSSOP package.
Device Information(1)
PART NUMBER
LM8272
PACKAGE
VSSOP (8)
BODY SIZE (NOM)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
Large Signal Step Response
for Various Cap. Load
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM8272
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
4
4
5
6
8
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
5V Electrical Characteristics .....................................
12V Electrical Characteristics ...................................
Typical Performance Characteristics ........................
Application and Implementation ........................ 14
7.1 Block Diagram and Operational Description
A) Input Stage: .........................................................
B) Output Stage: .....................................................
C) Output Voltage Swing Close to V−: ....................
Driving Capactive Loads: ........................................
Estimating the Output Voltage Swing .....................
Output Short Circuit Current and Dissipation
Issues:......................................................................
7.7 Other Application Hints: ..........................................
7.8 LM8272 Advantages: ..............................................
7.2
7.3
7.4
7.5
7.6
8
17
18
18
Device and Documentation Support.................. 19
8.1
8.2
8.3
8.4
9
14
15
15
16
16
Community Resources............................................
Trademarks .............................................................
Electrostatic Discharge Caution ..............................
Glossary ..................................................................
19
19
19
19
Mechanical, Packaging, and Orderable
Information ........................................................... 19
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (August 2014) to Revision F
Page
•
Changed pin 5 From: -IN B To: +IN B Non-Inverting Input B in the Pin Functions table ....................................................... 3
•
Changed pin 6 From: +IN B To: -IN B Inverting Input B in the Pin Functions table............................................................... 3
•
Moved "Storage temperature range" to the Absolute Maximum Ratings (1) (2) ........................................................................ 4
•
Changed Handling Ratings To: ESD Ratings ........................................................................................................................ 4
Changes from Revision D (March 2013) to Revision E
Page
•
Changed data sheet structure and organization. Added, updated, or renamed the following sections: Device
Information Table, Application and Implementation; Power Supply Recommendations; Mechanical, Packaging, and
Ordering Information. ............................................................................................................................................................. 1
•
Deleted TJ = 25°C................................................................................................................................................................... 5
•
Deleted TJ = 25°C .................................................................................................................................................................. 6
Changes from Revision C (March 2013) to Revision D
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 18
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
5 Pin Configuration and Functions
8-Pin VSSOP
Top View
Pin Functions
PIN
I/O
DESCRIPTION
NUMBER
NAME
1
OUT A
O
Output A
2
-IN A
I
Inverting Input A
3
+IN A
I
Non-Inverting Input A
4
V-
I
Negative Supply
5
+IN B
I
Non-Inverting Input B
6
-IN B
I
Inverting Input B
7
OUT B
O
Output B
8
V+
I
Positive Supply
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
3
LM8272
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings (1) (2)
over operating free-air temperature range (unless otherwise noted)
MIN
VIN Differential
Output Short Circuit Duration
MAX
UNIT
+/−10
V
See
(3) (4)
Supply Voltage (V+ - V−)
27
V
V+ +0.3, V− −0.3
V
+150
°C
+150
°C
Infrared or Convection (20 sec.)
235
°C
Wave Soldering (10 sec.)
260
°C
Voltage at Input/Output pins
Junction Temperature
(5)
−65
Storage temperature range, Tstg
Soldering Information:
(1)
(2)
(3)
(4)
(5)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Rating indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C.
Output short circuit duration is infinite for VS ≤ 6 V at room temperature and below. For VS > 6 V, allowable short circuit duration is 1.5
ms.
The maximum power dissipation is a function of TJ(max), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/ RθJA. All numbers apply for packages soldered directly onto a PC board.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
(3)
Electrostatic discharge (1)
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (2)
±2000
Machine Model (MM) (3)
±200
UNIT
V
Human body model, 1.5 kΩ in series with 100 pF. Machine Model, 0 Ω is series with 200 pF.
JEDEC document JEP155 states that 2000-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 200-V MM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
Supply Voltage (V+ - V−)
Operating Temperature Range (1)
(1)
NOM
MAX
UNIT
2.5
24
V
−40
+85
°C
The maximum power dissipation is a function of TJ(max), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/ RθJA. All numbers apply for packages soldered directly onto a PC board.
6.4 Thermal Information
THERMAL METRIC (1)
RθJA
(1)
(2)
4
Junction-to-ambient thermal resistance (2)
DGK
8 Pins
235
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
The maximum power dissipation is a function of TJ(max), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) - TA)/ RθJA. All numbers apply for packages soldered directly onto a PC board.
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
6.5 5V Electrical Characteristics
Unless otherwise specified, all limited ensured for V+ = 5V, V− = 0V, VCM = 0.5V, VO = V+/2, and RL > 1MΩ to V−. Boldface
limits apply at the temperature extremes.
PARAMETER
TEST CONDITIONS
VOS
Input Offset Voltage
VCM = 0.5V & VCM = 4.5V
TC VOS
Input Offset Average Drift
VCM = 0.5V & VCM = 4.5V (3)
IB
Input Bias Current
See
IOS
Input Offset Current
CMRR
Common Mode Rejection Ratio
VCM stepped from 0V to 5V
+PSRR
Positive Power Supply Rejection Ratio
V+ from 4.5V to 13V
CMVR
Input Common-Mode Voltage Range
CMRR > 50dB
TYP (1)
LIMIT (2)
UNIT
+/−0.7
+/−5
+/− 7
mV
max
+/−2
—
—
±2.00
±2.70
µA
max
20
250
400
nA
max
80
64
61
dB
min
100
78
74
dB
min
−0.3
−0.1
0.0
V
max
5.3
5.1
5.0
V
min
80
64
60
dB
min
V
min
(4)
AVOL
Large Signal Voltage Gain
VO = 0.5 to 4.5V,
RL = 10kΩ to V+/2
VO
Output Swing
High
RL = 10kΩ to V−
4.93
4.85
ISOURCE = 5mA
4.85
4.70
Output Swing
Low
RL = 10kΩ to V+
215
250
ISINK = 5mA
300
350
Output Short Circuit Current
Sourcing to V−
VID = 200mV (5)
100
—
Sinking to V+
VID = −200mV (5)
100
—
ISC
µV/°C
mV
max
mA
IOUT
Output Current
VID = ±200mV, VO = 1V from rails
±55
—
mA
IS
Supply Current (Both Channel)
No load, VCM = 0.5V
1.8
2.3
2.8
mA
max
SR
Slew Rate (6)
AV = +1, VI = 5VPP
12
—
V/µs
fu
Unity Gain Frequency
VI = 10mVp, RL = 2KΩ to V+/2
7.5
—
MHz
GBWP
Gain-Bandwidth Product
f = 50KHz
13
—
MHz
Phim
Phase Margin
VI = 10mVp, RL = 2kΩ to V+/2
55
—
deg
en
Input-Referred Voltage Noise
f = 2KHz, RS = 50Ω
15
—
nV/√Hz
in
Input-Referred Current Noise
f = 2KHz
1.4
—
pA/√Hz
fmax
Full Power Bandwidth
ZL = (20pF || 10kΩ) to V+/2
700
—
kHz
(1)
(2)
(3)
(4)
(5)
(6)
Typical Values represent the most likely parametric norm.
All limits are ensured by testing or statistical analysis.
Offset voltage average drift determined by dividing the change in VOS at temperature extremes into the total temperature change.
Positive current corresponds to current flowing into the device.
Short circuit test is a momentary test. Output short circuit duration is infinite for VS ≤ 6V at room temperature and below. For VS > 6V,
allowable short circuit duration is 1.5ms.
Slew rate is the slower of the rising and falling slew rates. Connected as a Voltage Follower.
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
5
LM8272
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
www.ti.com
6.6 12V Electrical Characteristics
Unless otherwise specified, all limited ensured for V+ = 12V, V− = 0V, VCM = 6V, VO = 6V, and RL > 1MΩ to V−. Boldface
limits apply at the temperature extremes.
PARAMETER
TEST CONDITIONS
VOS
Input Offset Voltage
VCM = 0.5V & VCM = 11.5V
TC VOS
Input Offset Average Drift
VCM = 0.5V & VCM = 11.5V (3)
IB
Input Bias Current
See
IOS
Input Offset Current
CMRR
Common Mode Rejection Ratio
VCM stepped from 0V to 12V
+PSRR
Positive Power Supply Rejection Ratio
V+ from 4.5V to 13V, VCM = 0.5V
−PSRR
Negative Power Supply Rejection Ratio
CMVR
Input Common-Mode Voltage Range
TYP (1)
LIMIT (2)
UNIT
+/−0.7
+/−7
+/− 9
mV
max
+/−2
—
—
±2.00
±2.80
µA
max
30
275
550
nA
max
88
74
72
dB
min
100
78
74
dB
min
85
—
dB
−0.3
−0.1
0
V
max
12.3
12.1
12.0
V
min
83
74
70
dB
min
V
min
(4)
CMRR > 50dB
AVOL
Large Signal Voltage Gain
VO = 1V to 11V
RL = 10kΩ to V+/2
VO
Output Swing
High
RL 10kΩ to V+/2
11.8
11.7
ISOURCE = 5mA
11.6
11.5
Output Swing
Low
RL = 10kΩ to V+/2
0.25
0.3
.40
.45
Output Short Circuit Current
Sourcing to V−
VID = 200mV (5)
130
110
130
110
ISC
ISINK = 5mA
+
Sinking to V
VID = 200mV
(5)
µV/°C
V
max
mA
min
IOUT
Output Current
VID = ±200mV, VO = 1V from rails
±65
—
mA
IS
Supply Current (Both Channel)
No load, VCM = 0.5V
1.9
2.4
2.9
mA
max
SR
Slew Rate (6)
AV = +1, VI = 10VPP, CL = 10pF
15
—
AV = +1, VI = 10VPP, CL = 0.1µF
1
—
V/µs
ROUT
Close Loop Output Resistance
AV = +1, f = 100KHz
3
—
Ω
fu
Unity Gain Frequency
VI = 10mVp, RL = 2kΩ to V+/2
8
—
MHz
GBWP
Gain-Bandwidth Product
f = 50KHz
15
—
MHz
Phim
Phase Margin
VI = 10mVp, RL = 2kΩ to V+/2
57
—
Deg
GM
Gain Margin
VI = 10mVp, RL = 2kΩ to V+/2
20
—
dB
AV = +1, RL = 2kΩ to V /2
12.5
—
AV = +1, RL = 600Ω to V+/2
10.5
—
AV = +10, RL = 600Ω to V+/2
1.0
—
−3dB BW
(1)
(2)
(3)
(4)
(5)
(6)
6
Small Signal -3db Bandwidth
+
MHz
Typical Values represent the most likely parametric norm.
All limits are ensured by testing or statistical analysis.
Offset voltage average drift determined by dividing the change in VOS at temperature extremes into the total temperature change.
Positive current corresponds to current flowing into the device.
Short circuit test is a momentary test. Output short circuit duration is infinite for VS ≤ 6V at room temperature and below. For VS > 6V,
allowable short circuit duration is 1.5ms.
Slew rate is the slower of the rising and falling slew rates. Connected as a Voltage Follower.
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
12V Electrical Characteristics (continued)
Unless otherwise specified, all limited ensured for V+ = 12V, V− = 0V, VCM = 6V, VO = 6V, and RL > 1MΩ to V−. Boldface
limits apply at the temperature extremes.
PARAMETER
TEST CONDITIONS
TYP (1)
LIMIT (2)
15
—
nV/√Hz
UNIT
en
Input-Referred Voltage Noise
f = 2KHz, RS = 50Ω
in
Input-Referred Current Noise
f = 2KHz
1.4
—
pA/√Hz
fmax
Full Power Bandwidth
ZL = (20pF || 10kΩ) to V+/2
300
—
kHz
THD+N
Total Harmonic Distortion +Noise
AV = +2, RL = 2kΩ to V+/2
VO = 8VPP, VS = ±5V
0.02%
—
CT Rej.
Cross-Talk Rejection
f = 5MHz, Driver RL = 10kΩ to V+/2
68
—
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
dB
7
LM8272
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
www.ti.com
6.7 Typical Performance Characteristics
Figure 1. VOS Distribution
Figure 2. VOS vs. VCM for 3 Representative Units
Figure 3. VOS vs. VCM for 3 Representative Units
Figure 4. VOS vs. VCM for 3 Representative Units
Figure 5. VOS vs. VS for 3 Representative Units
8
Figure 6. VOS vs. VS for 3 Representative Units
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
Typical Performance Characteristics (continued)
Figure 7. VOS vs. VS for 3 Representative Units
Figure 8. IB vs. VS
Figure 9. IB vs. VS
Figure 10. IS vs. VCM
Figure 12. IS vs. VS
Figure 11. IS vs. VCM
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
9
LM8272
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
www.ti.com
Typical Performance Characteristics (continued)
10
Figure 13. IS vs. VS
Figure 14. CMRR vs. Frequency
Figure 15. +PSRR vs. Frequency
Figure 16. −PSRR vs. Frequency
Figure 17. Open Loop Gain/Phase
for Various Supplies
Figure 18. Closed Loop Frequency Response
for Various Gains
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
Typical Performance Characteristics (continued)
Figure 19. Closed Loop Frequency Response
for Various Gains
Figure 20. Closed Loop Frequency Response
for Various RL
Figure 21. Maximum Output Swing vs. Load
(1% Distortion)
Figure 22. Maximum Output Swing vs. Frequency
(1% Distortion)
Figure 23. Closed Loop Small Signal Frequency Response
for Various CL
Figure 24. Overshoot vs. Cap Load
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
11
LM8272
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
www.ti.com
Typical Performance Characteristics (continued)
12
Figure 25. Settling Time (±1%) & Slew Rate vs. Cap Load
Figure 26. VOUT from V+ vs. ISOURCE
Figure 27. VOUT from V− vs. ISINK
Figure 28. Step Response for Various Amplitudes
Figure 29. Step Response for Various Amplitudes
Figure 30. Large Signal Step Response
for Various Cap Loads
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
Typical Performance Characteristics (continued)
Figure 31. THD+N vs. Input Amplitude
for Various Frequency
Figure 32. Input Referred Noise Density
Figure 33. Closed Loop Output Impedance vs. Frequency
Figure 34. Crosstalk Rejection vs. Frequency
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
13
LM8272
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
www.ti.com
7 Application and Implementation
7.1 Block Diagram and Operational Description
A) Input Stage:
As seen in Figure 35, the input stage consists of two distinct differential pairs (Q1-Q2 and Q3-Q4) in order to
accommodate the full Rail-to-Rail input common mode voltage range. The voltage drop across R5, R6, R7 and
R8 is kept to less than 200 mV in order to allow the input to exceed the supply rails. Q13 acts as a switch to
steer current away from Q3-Q4 and into Q1-Q2, as the input increases beyond 1.4 of V+. This in turn shifts the
signal path from the bottom stage differential pair to the top one and causes a subsequent increase in the supply
current.
In transitioning from one stage to another, certain input stage parameters (VOS, Ib, IOS, en, and in) are determined
based on which differential pair is “on” at the time. Input Bias current, Ib, will change in value and polarity as the
input crosses the transition region. In addition, parameter such as PSRR and CMRR which involve the input
offset voltage will also be effected by changes in VCM across the differential pair transition region.
Figure 35. Simplified Schematic Diagram
14
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
Block Diagram and Operational Description
A) Input Stage: (continued)
The input stage is protected with the combination of R9-R10 and D1, D2, D3 and D4 against differential input
over-voltages. This fault condition could otherwise harm the differential pairs or cause offset voltage shift in case
of prolonged over voltage. As shown in Figure 36, if this voltage reaches approximately ±1.4V at 25°C, the
diodes turn on and current flow is limited by the internal series resistors (R9 and R10). The Absolute Maximum
Rating of ±10V differential on VIN still needs to be observed. With temperature variation, the point were the
diodes turn on will change at the rate of 5mV/°C
Figure 36. Input Stage Current vs. Differential Input Voltage
7.2 B) Output Stage:
The output stage (see Figure 35) is comprised of complimentary NPN and PNP common-emitter stages to permit
voltage swing to within a Vce(sat) of either supply rail. Q9 supplies the sourcing and Q10 supplies the sinking
current load. Output current limiting is achieved by limiting the Vce of Q9 and Q10. Using this approach to current
limiting alleviates the drawback to the conventional scheme which requires one Vbe reduction in output swing.
The frequency compensation circuit includes Miller capacitors from collector to base of each output transistor
(see Figure 35, Ccomp9 and Ccomp10). At light capacitive loads, the high frequency gain of the output transistors is
high, and the Miller effect increases the effective value of the capacitors thereby stabilizing the Op Amp. Large
capacitive loads greatly decrease the high frequency gain of the output transistors thus lowering the effective
internal Miller capacitance - the internal pole frequency increases at the same time a low frequency pole is
created at the Op Amp output due to the large load capacitor. In this fashion, the internal dominant pole
compensation, which works by reducing the loop gain to less than 0dB when the phase shift around the feedback
loop is more than 180°, varies with the amount of capacitive load and becomes less dominant when the load
capacitor has increased enough. Hence the Op Amp is very stable even at high values of load capacitance
resulting in the uncharacteristic feature of stability under all capacitive loads.
7.3 C) Output Voltage Swing Close to V−:
The LM8272's output stage design allows voltage swings to within millivolts of either supply rail for maximum
flexibility and improved useful range. Because of this design architecture, as can be seen from Figure 35
diagram, with Output approaching either supply rail, either Q9 or Q10 Collector-Base junction reverse bias will
decrease. With output less than a Vbe from either rail, the corresponding output transistor operates near
saturation. In this mode of operation, the transistor will exhibit higher junction capacitance and lower ft which will
reduce Phase Margin. With the Noise Gain (NG = 1 + Rf/Rg, Rf & Rg are external gain setting resistors) of 2 or
higher, there is sufficient Phase Margin that this reduction (in Phase Margin) is of no consequence. However,
with lower Noise Gain ( 4.7µF). The large capacitor can be shared by more than one device if necessary. The small
ceramic capacitor maintains low supply impedance at high frequencies while the large capacitor will act as the
charge “bucket” for fast load current spikes at the Op Amp output. The combination of these capacitors will
provide supply decoupling and will help keep the Op Amp oscillation free under any load.
7.8 LM8272 Advantages:
Compared to other Rail-to-Rail Input/Output devices, the LM8272 offers several advantages such as:
• Improved cross over distortion
• Nearly constant supply current throughout the output voltage swing range and close to either rail.
• Nearly constant Unity gain frequency (fu) and Phase Margin (Phim) for all operating supplies and load
conditions.
• No output phase reversal under input overload condition.
18
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
LM8272
www.ti.com
SNOS515F – OCTOBER 2000 – REVISED AUGUST 2015
8 Device and Documentation Support
8.1 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
8.2 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
8.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
8.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
9 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2000–2015, Texas Instruments Incorporated
Product Folder Links: LM8272
19
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM8272MM
NRND
VSSOP
DGK
8
1000
Non-RoHS
& Green
Call TI
Level-1-260C-UNLIM
-40 to 85
A60
LM8272MM/NOPB
ACTIVE
VSSOP
DGK
8
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 85
A60
LM8272MMX/NOPB
ACTIVE
VSSOP
DGK
8
3500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 85
A60
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of