LMH6732MFX

LMH6732 www.ti.com SNOSA47B – FEBRUARY 2003 – REVISED MARCH 2013 LMH6732 High Speed Op Amp with Adjustable Bandwidth Check for Samples: LMH6732 FEATURES APPLICATIONS • • • • • 1 2 • • • • • • • Exceptional Performance at Any Supply Current: VS = ±5V, TA = 25°C, AV = +2V/V, VOUT = 2VPP, Typical unless Noted: ICC (mA) -3dB BW (MHz) DG/DP (%/deg.) PAL Slew Rate (V/μs) THD 1MHz (dBc) Output Current (mA) 1.0 55 0.20 / 0.036 400 -70.0 9 3.4 180 0.022 / 0.017 2100 -78.5 45 9.0 540 0.025 / 0.010 2700 -79.6 115 Ultra High Speed (−3dB BW) 1.5GHz (ICC = 10mA, 0.25VPP) Single Resistor Adjustability of Supply Current Fast Enable/ Disable Capability 20ns (ICC = 9mA) "Popless" Output on "Enable" 15mV (ICC = 1mA) Ultra Low Disable Current 1MHz 2.5 nV/√Hz IN Input Referred Inverting Noise Current >1MHz 9.7 pA/√Hz INN Input Referred Non-Inverting Noise Current >1MHz 1.8 pA/√Hz SNF Noise Floor >1MHz −154 dBm1Hz INV Total Integrated Input Noise 1MHz to 200MHz 60 μV (1) (2) (3) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Min/Max ratings are based on production testing unless otherwise specified. Typical numbers are the most likely parametric norm. Bold numbers refer to over temperature limits. Slew Rate is the average of the rising and falling edges. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMH6732 3 LMH6732 SNOSA47B – FEBRUARY 2003 – REVISED MARCH 2013 www.ti.com Electrical Characteristics ICC = 9mA(1) (continued) AV = +2, RF = 700Ω, VS = ±5V, RL = 100Ω, RP = 39kΩ; Unless otherwise specified. Symbol Parameter Conditions Min (2) Typ (2) Max (2) Units ±3.0 ±8.0 9.9 mV Static, DC Performance VIO Input Offset Voltage DVIO Input Offset Voltage Average Drift See (4) μV/°C 16 (5) IBN Input Bias Current Non Inverting DIBN Input Bias Current Average Drift Non-Inverting (4) −2 ±11 ±12 5 (5) −9 μA nA/°C ±20 ± 30 μA IBI Input Bias Current Inverting DIBI Input Bias Current Average Drift Inverting (4) −14 nA/°C +PSRR Positive Power Supply Rejection Ratio DC 52 50 62 dB −PSRR Negative Power Supply Rejection Ratio DC 51 48 56 dB CMRR Common Mode Rejection Ratio DC 49 46 52 dB ICC Supply Current RL = ∞, RP = 39kΩ 7.5 6.6 9.0 ICCI Supply Current During Shutdown 10.5 11.7 mA 1MHz 8.8 pA/√Hz INN Input Referred Non-Inverting Noise Current >1MHz 1.1 pA/√Hz SNF Noise Floor >1MHz −151 dBm1Hz INV Total Integrated Input Noise 1MHz to 100MHz 60 μV (1) (2) (3) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Min/Max ratings are based on production testing unless otherwise specified. Typical numbers are the most likely parametric norm. Bold numbers refer to over temperature limits. Slew Rate is the average of the rising and falling edges. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMH6732 5 LMH6732 SNOSA47B – FEBRUARY 2003 – REVISED MARCH 2013 www.ti.com Electrical Characteristics ICC = 3.4mA(1) (continued) AV = +2, RF = 1kΩ, VS = ±5V, RL = 100Ω, RP = 137kΩ; Unless otherwise specified. Symbol Parameter Conditions Min (2) Typ Max Units ±2.5 ±7.0 ±8.5 mV (2) (2) Static, DC Performance VIO Input Offset Voltage DVIO Input Offset Voltage Average Drift See (4) IBN Input Bias Current Non Inverting (5) −0.4 DIBN Input Bias Current Average Drift Non-Inverting (4) 8 μV/°C 10 ±4 ±6 μA nA/°C (5) −1 −3 nA/°C ±12 ±16 μA IBI Input Bias Current Inverting DIBI Input Bias Current Average Drift Inverting (4) +PSRR Positive Power Supply Rejection Ratio DC 52 50 64 dB −PSRR Negative Power Supply Rejection Ratio DC 51 50 57 dB CMRR Common Mode Rejection Ratio DC 49 48 55 dB ICC Supply Current RL = ∞, RP = 137kΩ 2.8 2.6 3.4 ICCI Supply Current During Shutdown 3.9 4.1 mA 1MHz 9.0 pA/√Hz INN Input Referred Non-Inverting Noise Current >1MHz 0.8 pA/√Hz SNF Noise Floor >1MHz −147 dBm1Hz INV Total Integrated Input Noise 1MHz to 100MHz 29 μV (1) (2) (3) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Min/Max ratings are based on production testing unless otherwise specified. Typical numbers are the most likely parametric norm. Bold numbers refer to over temperature limits. Slew Rate is the average of the rising and falling edges. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMH6732 7 LMH6732 SNOSA47B – FEBRUARY 2003 – REVISED MARCH 2013 www.ti.com Electrical Characteristics ICC = 1.0mA(1) (continued) AV = +2, RF = 1kΩ, VS = ±5V, RL = 500Ω, RP = 412kΩ; Unless otherwise specified. Symbol Parameter Conditions Min (2) Typ Max Units ±1.6 ±6.0 ±7.3 mV (2) (2) Static, DC Performance VIO Input Offset Voltage DVIO Input Offset Voltage Average Drift See (4) IBN Input Bias Current Non Inverting (5) 0.04 DIBN Input Bias Current Average Drift Non-Inverting (4) −1 μV/°C 4 (5) IBI Input Bias Current Inverting DIBI Input Bias Current Average Drift Inverting (4) +PSRR Positive Power Supply Rejection Ratio DC −PSRR Negative Power Supply Rejection Ratio CMRR −0.1 ±2.0 ±2.5 μA nA/°C ±6 ±8 μA −3 nA/°C 52 51 64 dB DC 51 49 59 dB Common Mode Rejection Ratio DC 49 47 55 dB ICC Supply Current RL = ∞, RP = 412kΩ 0.70 0.66 1.0 ICCI Supply Current During Shutdown 1.3 1.4 mA