This evaluation board contains the LMP7312, along with a SPI command generator to program the registers
in the LMP7312
.Connectors,
JUMPERS
Jumpers, Test Point
The eval board has 6 jumpers:
POWER SUPPLY
+Vs
banana plug for the positive power
supply of the LMP7312 and the onboard SPI command generator.
VIO
banana plug to power the SPI of the
LMP7312 when an external micro is
used to program the SPI.
GND
banana plug for ground connection.
SIGNAL CONNECTORS
J1
connects the CSB pin of the LMP7312 to
either the onboard SPI commands generator
or to pin 1 of J7.
J2
connects the SCK pin of the LMP7312 to
either the onboard SPI commands generator
or to pin 3 of J7.
J3
connects the SDI pin of the LMP7312 to
either the onboard SPI commands generator
or to pin 5 of J7.
J4
connects the -VOUT/VR pin of the LMP7312
either to the VR reference or to the LOAD.
(see the Output Configuration section).
J5
connects the VOCM pin of the LMP7312 to
either the ground or to the VOCM reference.
(see the Output Configuration section).
J6
connects the VIO pin of the LMP7312 to
either the +Vs plug or to the VIO plug.
Input signals
+IN_CL
banana plug for non-inverting input of
the amplification pair.
-IN_CL
banana plug for inverting input of the
amplification pair.
+IN_LS
BNC for non-inverting input of the
attenuation pair.
-IN_LS
BNC for inverting
attenuation pair.
J7
14-pin
header
available
for
microcontroller connection. The pin out
is shown in Table 3.
input
of
TEST POINTS
the
The test points are connected as follows:
TP1
TP2
TP3
TP4
TP5
TP6
TP7
TP8
TP9
TP10
TP11
Reference Signals
Vocm
banana plug for the common mode
output signals and the output
configuration
(single
ended,
differential).
See
the
Output
Configuration section.
VR
banana plug for the output reference
when the output of the LMP7312 is
used in single ended mode.
Output signals
OUT-
BNC for the inverting Output in the
differential output configuration
OUT+
BNC for the non-inverting output.
DP
Differential Probe Header connector.
P1
5-pin header for ADC141S626 or
ADC161S626 Eval Board connection.
1
GND
-IN pin
-VIN pin
-VOUT/VR pin
+IN pin
+VIN pin
+VOUT pin
VR
VOCM
+Vs
VIO
LMP7312 Evaluation Board User Guide (551600360-001 REV A)
LMP7312 Evaluation Board User Guide (551600360-001 REV A)
•
REGISTER PROGRAMMING SETUP
Single ended mode
• Short jumper J4
• Short pin2 and pin3 of J5
• Connect a supply in the range between 0V
and 5V between VR and GND banana plugs
In order to use the on board SPI commands
generator to program the LMP7312 the following
jumpers need to be configured as follows:
J1
open
J2
open
J3
open
J6
short pin1 to pin 2
Connect a supply in the range between 1V
and 5V to the +Vocm and GND banana plugs
COMPONENTS
If the device is configured in the differential output
mode, the series resistances R2 and R3, RLd
and the capacitance CLd can be changed in
order to build a first order low pass filter with
desired bandwidth. In this configuration the
capacitance CLs and the resistance RLs should
be removed.
If the device is configured in the single-ended
output mode, the series resistance R3, RLs and
capacitance CLs can be changed in order to build
a first order low pass filter with desired
bandwidth. In this configuration the capacitance
CLd and the resistance RLd should be removed.
If the value of the shunt resistance R1 does not fit
the application needs, replace it as needed
In order to use a microcontroller to program the
LMP7312 the following jumpers need to be
configured as follows:
J1
short
J2
short
J3
short
J6
short pin2 to pin 3
Connect the external microcontroller to J7.
Refer to Table 3 for J7 pin out.
POWER SUPPLY SETUP
When the LMP7312 is programmed through the
onboard SPI command generator, a 5V supply is
needed to power the eval board:
• Connect a +5V supply to the +Vs and GND
banana plugs
Using the Board
INPUT AND OUTPUT SIGNALS
When the LMP7312 is programmed through a
microcontroller:
• Connect a +5V supply between +Vs and GND
banana plugs
• Connect a supply (2.7V – 5.5V) that matches
microcontroller voltage range between +VIO
and GND banana plugs
Attenuation mode
Connect a signal at +IN_LS and –IN_LS BNC;
refer to the Datasheet for the allowed amplitude
according to the set gain.
Amplification mode
Connect a signal at +IN_CL and –IN_CL banana;
refer to the Datasheet for the allowed amplitude
according to the set gain.
SOURCE SETUP
Attenuation input pair
If signal source impedance matching is desired,
solder the resistors R8 and R9 of appropriate
value.
PROGRAMMING THE LMP7312
The register in the LMP7312 can be programmed
using switches S1 and S2. S2 consists of five
switches labeled B0, B1, B2, B3, B4,
corresponding to the five bits of the LMP7312
register. If the switch is up a “0” is programmed to
the corresponding bit. S1 is used to load the data
into the register of the LMP7312.
For example, to load the gain of 0.384V/V set S2
as follows:
Gain_1 – Down 1
Gain_0 – Up
0
EN_CL
– Up
0
Null_SW – Up
0
HiZ
– Up
0
Then Push the switch S1 to load the data into the
register of the LMP7312.
Table 1 shows the allowed register values.
Amplification input pair
The 50Ω shunt resistor (R1) between the inputs
needs to be removed if the amplification input
pair is not used as a current loop receiver.
OUTPUT CONFIGURATION
The LMP7312 is able to work in both single
ended and differential output mode. The selection
of the output is made through the Vocm (output
common mode voltage) pin.
Differential mode
• Open jumper J4
• Short pin1 and pin2 of J5
2
LMP7312 Evaluation Board User Guide (551600360-001 REV A)
Hardware Setup
LSB
MSB
HI_Z
NULL_SW
EN_CL
Gain_0
Gain_1
Gain Value (V/V)
Mode of
Operation
0
0
0
0
0
0.096
Attenuation
0
0
0
1
0
0.192
Attenuation
0
0
0
0
1
0.384
Attenuation
0
0
0
1
1
0.768
Attenuation
0
0
1
0
1
1
Amplification
0
0
1
1
1
2
Amplification
1
x
x
x
x
-
High
Impedance
output
0
1
x
x
x
1
Null Switch
mode
Table 2 S2 Dip switch description
PINS
1-2
3-4
5-6
7-8
9-10
Table 3 J7 connector description
NAME
Hiz
Null_SW
EN_CL
Gain_0
Gain_1
PIN
1
2
3
4
5
6
7
WRITING TO THE REGISTER USING A
MICROCONTROLLER
NAME
CSB
GND
SCK
NC
SDI
NC
SDO
PIN
8
9
10
11
12
13
14
NAME
NC
NC
NC
NC
NC
NC
NC
Interfacing ADC Eval Board
A microcontroller can be used to program the
LMP7312. If the microcontroller is provided with a
TTL logic signal connect pin1 and pin2 of J6
together, otherwise, apply a voltage compliant
with the microcontroller logic value to the VIO
banana plug, and short pin2 and pin3 of J6. The
microcontroller signals are connected to the
LMP7312 through J7. More information on the
SPI configuration is provided in the SPI section of
the LMP7312 datasheet.
The LMP7312 Eval Board can be interfaced with
the ADC141S626 and ADC161S626 Eval Boards
through the P1 connector only when the
LMP7312 is configured in the differential output
mode (see Output Configuration section).
Table 4 P1 connector description
PIN
NAME
3
1
Vs
2
GND
3
OUT-
4
GND
5
OUT+
LMP7312 Evaluation Board User Guide (551600360-001 REV A)
Table 1 Register Values
LMP7312 Evaluation Board User Guide (551600360-001 REV A)
Schematic
4
Top layer
Bottom layer
5
LMP7312 Evaluation Board User Guide (551600360-001 REV A)
Board Layout
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated