Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
LMT84 1.5-V, SC70/TO-92/TO-92S,
Analog Temperature Sensors
1 Features
3 Description
•
The LMT84 is a precision CMOS temperature sensor
with ±0.4°C typical accuracy (±2.7°C maximum) and
a linear analog output voltage that is inversely
proportional to temperature. The 1.5-V supply voltage
operation, 5.4-μA quiescent current, and 0.7-ms
power-on time enable effective power-cycling
architectures to minimize power consumption for
battery-powered applications such as drones and
sensor nodes. The LMT84LPG through-hole TO-92S
package fast thermal time constant supports offboard time-temperature sensitive applications such
as smoke and heat detectors. The accuracy over the
wide operating range and other features make the
LMT84 an excellent alternative to thermistors.
1
•
•
•
•
•
•
•
•
•
LMT84LPG (TO-92S package) has a Fast
Thermal Time Constant, 10-s Typical (1.2 m/s
Airflow)
Very Accurate: ±0.4°C Typical
Low 1.5-V Operation
Average Sensor Gain of -5.5 mV/°C
Low 5.4-µA Quiescent Current
Wide Temperature Range: –50°C to 150°C
Output is Short-Circuit Protected
Push-Pull Output With ±50-µA Drive Capability
Footprint Compatible With the Industry-Standard
LM20/19 and LM35 Temperature Sensors
Cost-Effective Alternative to Thermistors
2 Applications
•
•
•
•
•
Infotainment and Cluster
Powertrain Systems
Smoke and Heat Detectors
Drones
Appliances
For devices with different average sensor gains and
comparable
accuracy,
refer
to
Comparable
Alternative Devices for alternative devices in the
LMT8x family.
Device Information (1)
PART NUMBER
LMT84
(1)
PACKAGE
BODY SIZE (NOM)
SOT (5)
2.00 mm x 1.25 mm
TO-92 (3)
4.30 mm x 3.50 mm
TO-92S (3)
4.00 mm x 3.15 mm
For all available packages, see the orderable addendum
addendum at the end of the data sheet.
Thermal Time Constant
Output Voltage vs Temperature
100%
VDD (+1.5V to +5.5V)
FINAL TEMPERATURE
90%
VDD
80%
70%
LMT84
60%
CBP
50%
OUT
40%
30%
GND
20%
LMT8xLPG
Thermistor
10%
0
0
20
40
60
TIME (s)
80
100
Copyright © 2016, Texas Instruments Incorporated
D003
* Fast thermal response NTC
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Tables...................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
5
7.1
7.2
7.3
7.4
7.5
7.6
7.7
5
5
5
5
6
6
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Accuracy Characteristics...........................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
8.1 Overview ................................................................... 9
8.2 Functional Block Diagram ......................................... 9
8.3 Feature Description................................................... 9
8.4 Device Functional Modes........................................ 11
9
Application and Implementation ........................ 13
9.1 Applications Information.......................................... 13
9.2 Typical Applications ................................................ 13
10 Power Supply Recommendations ..................... 14
11 Layout................................................................... 15
11.1 Layout Guidelines ................................................. 15
11.2 Layout Examples................................................... 15
12 Device and Documentation Support ................. 16
12.1
12.2
12.3
12.4
12.5
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
16
16
16
16
16
13 Mechanical, Packaging, and Orderable
Information ........................................................... 16
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (June 2017) to Revision E
Page
•
Moved the automotive device to a standalone data sheet (SNIS178) ................................................................................... 1
•
Changed TO-92 GND pin number from: 1 to: 3 .................................................................................................................... 4
•
Changed TO-92 VDD pin number from: 3 to: 1 ...................................................................................................................... 4
Changes from Revision C (October 2015) to Revision D
Page
•
Updated data sheet text to the latest documentation and translations standards ................................................................. 1
•
Added AEC-Q100 automotive qualification bullets to Features ............................................................................................. 1
•
Added Time Constant graph................................................................................................................................................... 1
•
Removed disk drivers, games, wireless transceivers, and cell phones from Applications..................................................... 1
•
Added LPG (TO-92S) package .............................................................................................................................................. 4
•
Added Figure 10 to Typical Characteristics............................................................................................................................ 7
Changes from Revision B (May 2014) to Revision C
Page
•
Deleted all mentions of TO-126 package .............................................................................................................................. 1
•
Added TO-92 LPM pin configuration graphic ......................................................................................................................... 4
•
Changed Handling Ratings to ESD Ratings and moved Storage Temperature to Absolute Maximum Ratings table........... 5
•
Changed KV to V ................................................................................................................................................................... 5
•
Added layout recommendation for TO-92 LP and LPM packages....................................................................................... 15
Changes from Revision A (June 2013) to Revision B
Page
•
Changed data sheet flow and layout to conform with new TI standards. Added the following sections: Application
and Implementation, Power Supply Recommendations, Layout, Device and Documentation Support, Mechanical,
Packaging, and Orderable Information. ................................................................................................................................. 1
•
Added TO-92 and TO-126 package information throughout document. ................................................................................ 1
2
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
LMT84
www.ti.com
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
•
Changed from 450°C/W to 275 °C/W. New specification is derived using TI ' s latest methodology. .................................. 5
•
Deleted Note: The input current is leakage only and is highest at high temperature. It is typically only 0.001 µA. The
1 µA limit is solely based on a testing limitation and does not reflect the actual performance of the part. .......................... 6
5 Device Comparison Tables
Table 1. Available Device Packages
ORDER NUMBER
(1)
PACKAGE
PIN
BODY SIZE (NOM)
MOUNTING TYPE
LMT84DCK
SOT (AKA (2): SC70, DCK)
5
2.00 mm × 1.25 mm
Surface Mount
LMT84LP
TO-92 (AKA (2): LP)
3
4.30 mm × 3.50 mm
Through-hole; straight leads
(2)
LMT84LPG
TO-92S (AKA
3
4.00 mm × 3.15 mm
Through-hole; straight leads
LMT84LPM
TO-92 (AKA (2): LPM)
3
4.30 mm × 3.50 mm
Through-hole; formed leads
LMT84DCK-Q1
SOT (AKA (2): SC70, DCK)
5
2.00 mm × 1.25 mm
Surface Mount
(1)
(2)
: LPG)
For all available packages and complete order numbers, see the Package Option addendum at the end of the data sheet.
AKA = Also Known As
Table 2. Comparable Alternative Devices
DEVICE NAME
AVERAGE OUTPUT SENSOR GAIN
POWER SUPPLY RANGE
LMT84
–5.5 mV/°C
1.5 V to 5.5 V
LMT85
–8.2 mV/°C
1.8 V to 5.5 V
LMT86
–10.9 mV/°C
2.2 V to 5.5 V
LMT87
–13.6 mV/°C
2.7 V to 5.5 V
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
3
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
www.ti.com
6 Pin Configuration and Functions
LP Package
3-Pin TO-92
(Top View)
DCK Package
5-Pin SOT (SC70)
(Top View)
1
5
GND
GND
2
LMT84
GND
4
3
OUT
VDD
1
D
VD
G
3 D
N
2 T
U
O
LPG Package
3-Pin TO-92S
(Top View)
Scale: 4:1
1
2
3
LPM Package
3-Pin TO-92
(Top View)
1 T
U
O
3
D
VD
2 D
N
G
Scale: 4:1
1
D
VD
2 T
U
O
3 D
N
G
Scale: 4:1
Pin Functions
PIN
NAME
GND
SOT (SC70)
TO-92
TO-92S
1, 2 (1) , 5
3
2
TYPE
DESCRIPTION
EQUIVALENT CIRCUIT
Ground
N/A
FUNCTION
Power Supply Ground
VDD
OUT
3
2
1
Analog
Output
Outputs a voltage that is inversely
proportional to temperature
GND
VDD
(1)
4
4
1
3
Power
N/A
Positive Supply Voltage
Direct connection to the back side of the die
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
LMT84
www.ti.com
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
7 Specifications
7.1 Absolute Maximum Ratings
See
(1) (2)
MIN
MAX
UNIT
Supply voltage
–0.3
6
V
Voltage at output pin
–0.3
(VDD + 0.5)
V
Output current
–7
7
mA
Input current at any pin (3)
–5
5
mA
150
°C
150
°C
Maximum junction temperature (TJMAX)
Storage temperature Tstg
(1)
(2)
(3)
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Soldering process must comply with Reflow Temperature Profile specifications. Refer to www.ti.com/packaging.
When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > V), the current at that pin should be limited to 5 mA.
7.2 ESD Ratings
VALUE
UNIT
LMT84LP in TO-92/TO-92S package
V(ESD)
Electrostatic
discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) (2)
±2500
Charged-device model (CDM), per JEDEC specification JESD22-C101 (3)
±1000
Human-body model (HBM), per JESD22-A114 (2)
±2500
Charged-device model (CDM), per JEDEC specification JESD22-C101 (3)
±1000
V
LMT84DCK in SC70 package
V(ESD)
(1)
(2)
(3)
Electrostatic
discharge
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
The human body model is a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
MIN
Specified temperature
MAX
UNIT
TMIN ≤ TA ≤ TMAX
°C
−50 ≤ TA ≤ 150
°C
Supply voltage (VDD)
1.5
5.5
V
7.4 Thermal Information (1)
THERMAL METRIC (2)
(3) (4)
LMT84/
LMT84-Q1
LMT84LP
LMT84LPG
DCK (SOT/SC70)
LP/LPM (TO-92)
LPG (TO-92S)
5 PINS
3 PINS
3 PINS
275
167
UNIT
RθJA
Junction-to-ambient thermal resistance
130.4
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
84
90
64.2
°C/W
RθJB
Junction-to-board thermal resistance
56
146
106.2
°C/W
ψJT
Junction-to-top characterization parameter
1.2
35
14.6
°C/W
ψJB
Junction-to-board characterization parameter
55
146
106.2
°C/W
(1)
(2)
(3)
(4)
For information on self-heating and thermal response time see section Mounting and Thermal Conductivity.
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report.
The junction to ambient thermal resistance (RθJA) under natural convection is obtained in a simulation on a JEDEC-standard, High-K
board as specified in JESD51-7, in an environment described in JESD51-2. Exposed pad packages assume that thermal vias are
included in the PCB, per JESD 51-5.
Changes in output due to self heating can be computed by multiplying the internal dissipation by the thermal resistance.
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
5
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
www.ti.com
7.5 Accuracy Characteristics
These limits do not include DC load regulation. These stated accuracy limits are with reference to the values in Table 3.
MIN (1)
TYP (2)
MAX (1)
70°C to 150°C; VDD = 1.5 V to 5.5 V
–2.7
±0.6
2.7
°C
0°C to 70°C; VDD = 1.5 V to 5.5 V
–2.7
±0.9
2.7
°C
–50°C to +0°C; VDD = 1.6 V to 5.5 V
–2.7
±0.9
2.7
°C
PARAMETER
Temperature accuracy
(3)
TEST CONDITIONS
–50°C to +150°C; VDD = 2.3 V to 5.5 V
(1)
(2)
(3)
±0.4
UNIT
°C
Limits are specified to TI's AOQL (Average Outgoing Quality Level).
Typicals are at TJ = TA = 25°C and represent most likely parametric norm.
Accuracy is defined as the error between the measured and reference output voltages, tabulated in Table 3 at the specified conditions of
supply gain setting, voltage, and temperature (expressed in °C). Accuracy limits include line regulation within the specified conditions.
Accuracy limits do not include load regulation; they assume no DC load.
7.6 Electrical Characteristics
Unless otherwise noted, these specifications apply for VDD = +1.5 V to +5.5 V. minimum and maximum limits apply for TA = TJ
= TMIN to TMAX; typical values apply for TA = TJ = 25°C.
PARAMETER
TEST CONDITIONS
MIN (1)
TYP (2)
–1
–0.22
Sensor gain
(3)
Source ≤ 50 μA, (VDD – VOUT) ≥ 200 mV
Sink ≤ 50 μA, VOUT ≥ 200 mV
(4)
IS
Supply current
CL
Output load capacitance
Power-on time
(5)
(5)
6
0.26
UNIT
mV/°C
mV
1
200
mV
μV/V
TA = 30°C to 150°C, (VDD – VOUT) ≥ 100 mV
5.4
8.1
μA
TA = –50°C to 150°C, (VDD – VOUT) ≥ 100 mV
5.4
9
μA
1.9
ms
1100
CL= 0 pF to 1100 pF
Output drive
(1)
(2)
(3)
(4)
(1)
–5.5
Load regulation
Line regulation
MAX
0.7
±50
pF
µA
Limits are specific to TI's AOQL (Average Outgoing Quality Level).
Typicals are at TJ = TA = 25°C and represent most likely parametric norm.
Source currents are flowing out of the LMT84-xx. Sink currents are flowing into the LMT84-xx.
Line regulation (DC) is calculated by subtracting the output voltage at the highest supply voltage from the output voltage at the lowest
supply voltage. The typical DC line regulation specification does not include the output voltage shift discussed in Output Voltage Shift.
Specified by design and characterization.
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
LMT84
www.ti.com
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
7.7 Typical Characteristics
4
TEMPERATURE ERROR (ºC)
3
2
1
0
-1
-2
-3
-4
-50
-25
0
25
50
75
100 125 150
TEMPERATURE (ºC)
Figure 1. Temperature Error vs Temperature
Figure 2. Minimum Operating Temperature vs
Supply Voltage
Figure 3. Supply Current vs Temperature
Figure 4. Supply Current vs Supply Voltage
100
Figure 5. Load Regulation, Sourcing Current
Figure 6. Load Regulation, Sinking Current
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
7
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
www.ti.com
Typical Characteristics (continued)
1000
Figure 7. Change in Vout vs Overhead Voltage
Figure 8. Supply-Noise Gain vs Frequency
100%
FINAL TEMPERATURE
90%
80%
70%
60%
50%
40%
30%
20%
LMT8xLPG
Thermistor
10%
0
0
Figure 9. Output Voltage vs Supply Voltage
8
20
40
60
TIME (s)
80
100
D003
Figure 10. LMT84LPG Thermal Response vs Common
Leaded Thermistor With 1.2-m/s Airflow
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
LMT84
www.ti.com
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
8 Detailed Description
8.1 Overview
The LMT84 is an analog output temperature sensor. The temperature-sensing element is comprised of a simple
base emitter junction that is forward biased by a current source. The temperature-sensing element is then
buffered by an amplifier and provided to the OUT pin. The amplifier has a simple push-pull output stage thus
providing a low impedance output source.
8.2 Functional Block Diagram
Full-Range Celsius Temperature Sensor (−50°C to +150°C)
VDD
OUT
Thermal Diodes
GND
8.3 Feature Description
8.3.1 LMT84 Transfer Function
The output voltage of the LMT84, across the complete operating temperature range, is shown in Table 3. This
table is the reference from which the LMT84 accuracy specifications (listed in the Accuracy Characteristics
section) are determined. This table can be used, for example, in a host processor look-up table. A file containing
this data is available for download at the LMT84 product folder under Tools and Software Models.
Table 3. LMT84 Transfer Table
TEMP
(°C)
VOUT
(mV)
TEMP
(°C)
VOUT
(mV)
TEMP
(°C)
VOUT
(mV)
TEMP
(°C)
VOUT
(mV)
TEMP
(°C)
VOUT
(mV)
–50
1299
-10
1088
30
871
70
647
110
419
–49
1294
-9
1082
31
865
71
642
111
413
–48
1289
-8
1077
32
860
72
636
112
407
–47
1284
-7
1072
33
854
73
630
113
401
–46
1278
-6
1066
34
849
74
625
114
396
–45
1273
-5
1061
35
843
75
619
115
390
–44
1268
-4
1055
36
838
76
613
116
384
–43
1263
-3
1050
37
832
77
608
117
378
–42
1257
-2
1044
38
827
78
602
118
372
–41
1252
-1
1039
39
821
79
596
119
367
–40
1247
0
1034
40
816
80
591
120
361
–39
1242
1
1028
41
810
81
585
121
355
–38
1236
2
1023
42
804
82
579
122
349
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
9
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
www.ti.com
Feature Description (continued)
Table 3. LMT84 Transfer Table (continued)
TEMP
(°C)
VOUT
(mV)
TEMP
(°C)
VOUT
(mV)
TEMP
(°C)
VOUT
(mV)
TEMP
(°C)
VOUT
(mV)
TEMP
(°C)
VOUT
(mV)
–37
1231
3
1017
43
799
83
574
123
343
–36
1226
4
1012
44
793
84
568
124
337
–35
1221
5
1007
45
788
85
562
125
332
–34
1215
6
1001
46
782
86
557
126
326
–33
1210
7
996
47
777
87
551
127
320
–32
1205
8
990
48
771
88
545
128
314
–31
1200
9
985
49
766
89
539
129
308
–30
1194
10
980
50
760
90
534
130
302
–29
1189
11
974
51
754
91
528
131
296
–28
1184
12
969
52
749
92
522
132
291
–27
1178
13
963
53
743
93
517
133
285
–26
1173
14
958
54
738
94
511
134
279
–25
1168
15
952
55
732
95
505
135
273
–24
1162
16
947
56
726
96
499
136
267
–23
1157
17
941
57
721
97
494
137
261
–22
1152
18
936
58
715
98
488
138
255
–21
1146
19
931
59
710
99
482
139
249
–20
1141
20
925
60
704
100
476
140
243
–19
1136
21
920
61
698
101
471
141
237
–18
1130
22
914
62
693
102
465
142
231
–17
1125
23
909
63
687
103
459
143
225
–16
1120
24
903
64
681
104
453
144
219
–15
1114
25
898
65
676
105
448
145
213
–14
1109
26
892
66
670
106
442
146
207
–13
1104
27
887
67
664
107
436
147
201
–12
1098
28
882
68
659
108
430
148
195
–11
1093
29
876
69
653
109
425
149
189
150
183
Although the LMT84 is very linear, the response does have a slight umbrella parabolic shape. This shape is very
accurately reflected in Table 3. The transfer table can be calculated by using the parabolic equation (Equation 1).
VTEMP mV
870.6mV
mV
ª
º
«5.506 qC T 30qC »
¬
¼
mV
ª
2º
«0.00176 2 T 30qC »
qC
¬
¼
(1)
The parabolic equation is an approximation of the transfer table and the accuracy of the equation degrades
slightly at the temperature range extremes. Equation 1 can be solved for T, resulting in:
T
5.506
5.506 2
4 u 0.00176 u 870.6
2 u ( 0.00176)
VTEMP mV
30
(2)
For an even less accurate linear approximation, a line can easily be calculated over the desired temperature
range from the table using the two-point equation (Equation 3):
·
¹
V - V1 =
V2 - V1
T2 - T1
· u (T - T1)
¹
where
•
•
•
•
10
V is in mV,
T is in °C,
T1 and V1 are the coordinates of the lowest temperature,
and T2 and V2 are the coordinates of the highest temperature.
Submit Documentation Feedback
(3)
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
LMT84
www.ti.com
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
For example, if the user wanted to resolve this equation, over a temperature range of 20°C to 50°C, they would
proceed as follows:
760 mV - 925 mV ·
u (T - 20oC)
50oC - 20oC ¹
·
¹
V - 925 mV =
(4)
o
o
V - 925 mV = (-5.50 mV / C) u (T - 20 C)
(5)
o
V = (-5.50 mV / C) u T + 1035 mV
(6)
Using this method of linear approximation, the transfer function can be approximated for one or more
temperature ranges of interest.
8.4 Device Functional Modes
8.4.1 Mounting and Thermal Conductivity
The LMT84 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be
glued or cemented to a surface.
To ensure good thermal conductivity, the backside of the LMT84 die is directly attached to the GND pin. The
temperatures of the lands and traces to the other leads of the LMT84 will also affect the temperature reading.
Alternatively, the LMT84 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or
screwed into a threaded hole in a tank. As with any IC, the LMT84 and accompanying wiring and circuits must be
kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold
temperatures where condensation can occur. If moisture creates a short circuit from the output to ground or VDD,
the output from the LMT84 will not be correct. Printed-circuit coatings are often used to ensure that moisture
cannot corrode the leads or circuit traces.
The thermal resistance junction to ambient (RθJA or θJA) is the parameter used to calculate the rise of a device
junction temperature due to its power dissipation. Use Equation 7 to calculate the rise in the LMT84 die
temperature:
TJ = TA + TJA ª¬(VDDIS ) + (VDD - VO ) IL º¼
where
•
•
•
•
TA is the ambient temperature,
IS is the supply current,
ILis the load current on the output,
and VO is the output voltage.
(7)
For example, in an application where TA = 30°C, VDD = 5 V, IS = 5.4 μA, VOUT = 871 mV, and IL = 2 μA, the
junction temperature would be 30.015°C, showing a self-heating error of only 0.015°C. Because the junction
temperature of the LMT84 device is the actual temperature being measured, take care to minimize the load
current that the LMT84 is required to drive. Thermal Information shows the thermal resistance of the LMT84.
8.4.2 Output Noise Considerations
A push-pull output gives the LMT84 the ability to sink and source significant current. This is beneficial when, for
example, driving dynamic loads like an input stage on an analog-to-digital converter (ADC). In these applications
the source current is required to quickly charge the input capacitor of the ADC. The LMT84 is ideal for this and
other applications which require strong source or sink current.
The LMT84 supply-noise gain (the ratio of the AC signal on VOUT to the AC signal on VDD) was measured during
bench tests. The typical attenuation is shown in Figure 8 found in the Typical Characteristics section. A load
capacitor on the output can help to filter noise.
For operation in very noisy environments, some bypass capacitance should be present on the supply within
approximately 5 centimeters of the LMT84.
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
11
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
www.ti.com
Device Functional Modes (continued)
8.4.3 Capacitive Loads
The LMT84 handles capacitive loading well. In an extremely noisy environment, or when driving a switched
sampling input on an ADC, it may be necessary to add some filtering to minimize noise coupling. Without any
precautions, the LMT84 can drive a capacitive load less than or equal to 1100 pF as shown in Figure 11. For
capacitive loads greater than 1100 pF, a series resistor may be required on the output, as shown in Figure 12.
VDD
LMT84
OPTIONAL
BYPASS
CAPACITANCE
OUT
GND
CLOAD ” 1100 pF
Figure 11. LMT84 No Decoupling Required for Capacitive Loads Less Than 1100 pF
VDD
RS
LMT84
OUT
OPTIONAL
BYPASS
CAPACITANCE
GND
CLOAD > 1100 pF
Figure 12. LMT84 With Series Resistor for Capacitive Loading Greater Than 1100 pF
Table 4. Recommended Series Resistor Values
CLOAD
MINIMUM RS
1.1 nF to 99 nF
3 kΩ
100 nF to 999 nF
1.5 kΩ
1 μF
800 Ω
8.4.4 Output Voltage Shift
The LMT84 is very linear over temperature and supply voltage range. Due to the intrinsic behavior of an NMOS
or PMOS rail-to-rail buffer, a slight shift in the output can occur when the supply voltage is ramped over the
operating range of the device. The location of the shift is determined by the relative levels of VDD and VOUT. The
shift typically occurs when VDD – VOUT = 1 V.
This slight shift (a few millivolts) takes place over a wide change (approximately 200 mV) in VDD or VOUT.
Because the shift takes place over a wide temperature change of 5°C to 20°C, VOUT is always monotonic. The
accuracy specifications in the Accuracy Characteristics table already include this possible shift.
12
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
LMT84
www.ti.com
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Applications Information
The LMT84 features make it suitable for many general temperature-sensing applications. It can operate down to
1.5-V supply with 5.4-µA power consumption, making it ideal for battery-powered devices. Package options like
the through-hole TO-92 package allow the LMT84 to be mounted onboard, off-board, to a heat sink, or on
multiple unique locations in the same application.
9.2 Typical Applications
9.2.1 Connection to an ADC
Simplified Input Circuit of
SAR Analog-to-Digital Converter
Reset
+1.5V to +5.5V
Input
Pin
LMT84
VDD
CBP
RMUX
RSS
Sample
OUT
GND
CFILTER
CMUX
CSAMPLE
Figure 13. Suggested Connection to a Sampling Analog-to-Digital Converter Input Stage
9.2.1.1 Design Requirements
Most CMOS ADCs found in microcontrollers and ASICs have a sampled data comparator input structure. When
the ADC charges the sampling cap, it requires instantaneous charge from the output of the analog source such
as the LMT84 temperature sensor and many op amps. This requirement is easily accommodated by the addition
of a capacitor (CFILTER).
9.2.1.2 Detailed Design Procedure
The size of CFILTER depends on the size of the sampling capacitor and the sampling frequency. Because not all
ADCs have identical input stages, the charge requirements will vary. This general ADC application is shown as
an example only.
9.2.1.3 Application Curve
Figure 14. Analog Output Transfer Function
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
13
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
www.ti.com
Typical Applications (continued)
9.2.2 Conserving Power Dissipation With Shutdown
VDD
SHUTDOWN
VOUT
LMT84
Any logic
device output
Figure 15. Simple Shutdown Connection of the LMT84
9.2.2.1 Design Requirements
Because the power consumption of the LMT84 is less than 9 µA, it can simply be powered directly from any logic
gate output and therefore not require a specific shutdown pin. The device can even be powered directly from a
microcontroller GPIO. In this way, it can easily be turned off for cases such as battery-powered systems where
power savings are critical.
9.2.2.2 Detailed Design Procedure
Simply connect the VDD pin of the LMT84 directly to the logic shutdown signal from a microcontroller.
9.2.2.3 Application Curves
Time: 500 µs/div; Top trace: VDD 1 V/div;
Bottom trace: OUT 1 V/div
Figure 16. Output Turnon Response Time Without a
Capacitive Load and VDD= 3.3 V
Time: 500 µs/div; Top trace: VDD 2 V/div;
Bottom trace: OUT 1 V/div
Figure 17. Output Turnon Response Time Without a
Capacitive Load and VDD= 5 V
Time: 500 µs/div; Top trace: VDD 1 V/div;
Bottom trace: OUT 1 V/div
Figure 18. Output Turnon Response Time With 1.1-Nf
Capacitive Load and VDD= 3.3 V
Time: 500 µs/div; Top trace: VDD 2 V/div;
Bottom trace: OUT 1 V/div
Figure 19. Output Turnon Response Time With 1.1-Nf
Capacitive Load and VDD= 5 V
10 Power Supply Recommendations
The low supply current and supply range (1.5 V to 5.5 V) of the LMT84 allow the device to easily be powered
from many sources. Power supply bypassing is optional and is mainly dependent on the noise on the power
supply used. In noisy systems, it may be necessary to add bypass capacitors to lower the noise that is coupled
to the output of the LMT84.
14
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
LMT84
www.ti.com
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
11 Layout
11.1 Layout Guidelines
The LMT84 is extremely simple to layout. If a power-supply bypass capacitor is used, is should be connected as
shown in the Layout Examples.
11.2 Layout Examples
VIA to ground plane
VIA to power plane
GND
GND
GND
0.01µ F
OUT
VDD
Figure 20. SC70 Package Recommended Layout
GND
OUT
VDD
Figure 21. TO-92 LP Package Recommended Layout
GND
OUT
VDD
Figure 22. TO-92 LPM Package Recommended Layout
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
15
LMT84
SNIS167E – MARCH 2013 – REVISED OCTOBER 2017
www.ti.com
12 Device and Documentation Support
12.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
16
Submit Documentation Feedback
Copyright © 2013–2017, Texas Instruments Incorporated
Product Folder Links: LMT84
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LMT84DCKR
ACTIVE
SC70
DCK
5
3000
RoHS & Green
SN
Level-1-260C-UNLIM
-50 to 150
BNA
LMT84DCKT
ACTIVE
SC70
DCK
5
250
RoHS & Green
SN
Level-1-260C-UNLIM
-50 to 150
BNA
LMT84LP
ACTIVE
TO-92
LP
3
1800
RoHS & Green
SN
N / A for Pkg Type
-50 to 150
LMT84
LMT84LPG
ACTIVE
TO-92
LPG
3
1000
RoHS & Green
SN
N / A for Pkg Type
-50 to 150
LMT84
LMT84LPGM
ACTIVE
TO-92
LPG
3
3000
RoHS & Green
SN
N / A for Pkg Type
-50 to 150
LMT84
LMT84LPM
ACTIVE
TO-92
LP
3
2000
RoHS & Green
SN
N / A for Pkg Type
-50 to 150
LMT84
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
