LMV331, LMV393, LMV339
LMV393,
LMV339
SLCS136U – AUGUSTLMV331,
1999 – REVISED
OCTOBER
2020
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
www.ti.com
LMV331 Single, LMV393 Dual, LMV339 Quad General-purpose Low-voltage
Comparators
1 Features
3 Description
•
•
The LMV393 and LMV339 devices are low-voltage
(2.7 V to 5.5 V) versions of the dual and quad
comparators, LM393 and LM339, which operate from
5 V to 30 V. The LMV331 is the single-comparator
version.
•
•
•
2.7-V and 5-V Performance
Low Supply Current
– LMV331 130 μA Typ
– LMV393 210 μA Typ
– LMV339 410 μA Typ
Input Common-Mode Voltage Range Includes
Ground
Low Output Saturation Voltage 200 mV Typical
Open-Collector Output for Maximum Flexibility
The LMV331, LMV339, and LMV393 are the most
cost-effective solutions for applications where lowvoltage operation, low power, and space saving are
the primary specifications in circuit design for portable
consumer
products.
These
devices
offer
specifications that meet or exceed the familiar LM339
and LM393 devices at a fraction of the supply current.
2 Applications
•
•
•
•
•
Hysteresis Comparators
Oscillators
Window Comparators
Industrial Equipment
Test and Measurement
Device Information
PART NUMBER
BODY SIZE (NOM)
LMV339
SOIC (14)
8.65 mm x 3.90 mm
LMV393
SOIC (8)
4.90 mm x 3.90 mm
LMV331
SC70 (5)
2.00 mm x 1.25 mm
(1)
For all available packages, see the orderable addendum at
the end of the datasheet.
–
IN–
PACKAGE (PIN)(1)
OUT
+
IN+
Simplified Schematic
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
Submit Document Feedback
Copyright
© 2020 Texas
Instruments
Incorporated
intellectual
property
matters
and other important disclaimers. PRODUCTION DATA.
Product Folder Links: LMV331 LMV393 LMV339
1
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
Table of Contents
1 Features............................................................................1
2 Applications..................................................................... 1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings........................................ 4
6.2 ESD Ratings............................................................... 4
6.3 Recommended Operating Conditions.........................4
6.4 Thermal Information....................................................4
6.5 Electrical Characteristics, VCC+ = 2.7 V...................... 5
6.6 Electrical Characteristics, VCC+ = 5 V......................... 6
6.7 Switching Characteristics, VCC+ = 2.7 V..................... 6
6.8 Switching Characteristics, VCC+ = 5 V........................ 7
6.9 Typical Characteristics................................................ 7
7 Detailed Description........................................................9
7.1 Overview..................................................................... 9
7.2 Functional Block Diagram........................................... 9
7.3 Feature Description.....................................................9
7.4 Device Functional Modes............................................9
8 Application and Implementation.................................. 10
8.1 Application Information............................................. 10
8.2 Typical Application.................................................... 10
9 Power Supply Recommendations................................12
10 Layout...........................................................................12
10.1 Layout Guidelines................................................... 12
10.2 Layout Example...................................................... 12
11 Device and Documentation Support..........................13
11.1 Related Links.......................................................... 13
11.2 Trademarks............................................................. 13
11.3 Electrostatic Discharge Caution.............................. 13
11.4 Glossary.................................................................. 13
12 Mechanical, Packaging, and Orderable
Information.................................................................... 13
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision T (January 2015) to Revision U (October 2020)
Page
• Updated the numbering format for tables, figures and cross-references throughout the document...................1
Changes from Revision S (October 2012) to Revision T (January 2015)
Page
• Added Applications, Device Information table, Pin Functions table, ESD Ratings table, Thermal Information
table, Typical Characteristics, Feature Description section, Device Functional Modes, Application and
Implementation section, Power Supply Recommendations section, Layout section, Device and
Documentation Support section, and Mechanical, Packaging, and Orderable Information section................... 1
• Deleted Ordering Information table.....................................................................................................................1
Changes from Revision R (May 2012) to Revision S (October 2012)
Page
• Updated operating temperature range................................................................................................................4
Changes from Revision N (April 2011) to Revision O (February 2012)
Page
• Changed VI in the Absolute Maximum Ratings from 5.5 V to VCC+ ................................................................... 4
Changes from Revision M (November 2005) to Revision N (April 2011)
Page
• Changed document format from Quicksilver to DocZone...................................................................................1
• Added RUC package pin out drawing.................................................................................................................3
2
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
5 Pin Configuration and Functions
13
3
12
4
11
5
10
6
9
7
8
3OUT
4OUT
GND
4IN+
4IN–
3IN+
3IN–
LMV393 . . . D, DDU, DGK OR PW PACKAGE
(TOP VIEW)
1OUT
1IN–
1IN+
GND
1
VCC+
2OUT
2IN–
2IN+
8
2
7
3
6
4
5
3OUT
14
2
14
13
12
4OUT
2
11
GND
1IN–
3
10
4IN+
1IN+
4
9
4IN–
2IN–
5
8
3IN+
1OUT
1
VCC+
6
7
3IN–
1
2IN+
2OUT
1OUT
VCC+
1IN–
1IN+
2IN–
2IN+
2OUT
LMV339 . . . RUC PACKAGE
(TOP VIEW)
LMV339 . . . D OR PW PACKAGE
(TOP VIEW)
LMV331 . . . DBV OR DCK PACKAGE
(TOP VIEW)
1IN+
1
GND
2
1IN–
3
5
VCC+
4
OUT
Table 5-1. Pin Functions
PIN
NAME
LMV331
LMV393
DBV or
DCK
D, DDU,
DGK or PW
LMV339
D or PW
TYPE
DESCRIPTION
RUC
1IN– ,
2IN–,
3IN–,
4IN–
3
2, 6
4, 6, 8, 10
3, 5, 7, 9
I
Comparator(s) negative input pin(s)
1IN+ ,
2IN+,
3IN+,
4IN+
1
3, 5
5, 7, 9, 11
4, 6, 8, 10
I
Comparator(s) positive input pin(s)
GND
2
4
12
11
I
Ground
1OUT,
2OUT,
3OUT,
4OUT
4
1, 7
2, 1, 14, 13
1, 14, 13, 12
O
Comparator(s) output pin(s)
VCC+
5
8
3
2
I
Supply Pin
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
3
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
Supply voltage(2)
VCC
5.5
voltage(3)
VID
Differential input
VI
Input voltage range (either input)
0
At or below TA = 25°C,
VCC ≤ 5.5 V
Duration of output short circuit (one amplifier) to ground(4)
TJ
Operating virtual junction temperature
Tstg
Storage temperature range
(1)
UNIT
V
±5.5
V
VCC+
V
Unlimited
–65
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Section 6.3 is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values (except differential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
Differential voltages are at IN+ with respect to IN–.
Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
(2)
(3)
(4)
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(1)
±2000
Charged device model (CDM), per JEDEC specification JESD22-C101,
all pins(2)
±1000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
MIN
VCC
Supply voltage (single-supply operation)
VOUT
Output voltage
TA
Operating free-air temperature
MAX
2.7
UNIT
5.5
V
VCC+ + 0.3
V
125
°C
–40
6.4 Thermal Information
LMV339
THERMAL METRIC(1)
D
PW
LMV393
RUC
D
DDU
14 PINS
RθJA
Junction-to-ambient
thermal resistance
RθJC(top) Junction-to-case (top)
thermal resistance
PW
DBV
8 PINS
DCK
UNIT
5 PINS
86
113
216
97
210
172
149
206
252
—
—
51.3
—
—
—
—
—
—
—
59.0
—
—
—
—
—
—
RθJB
Junction-to-board
thermal resistance
—
ψJT
Junction-to-top
characterization
parameter
—
—
1.2
—
—
—
—
—
—
ψJB
Junction-to-board
characterization
parameter
—
—
59.0
—
—
—
—
—
—
(1)
4
LMV331
DGK
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
6.5 Electrical Characteristics, VCC+ = 2.7 V
VCC+ = 2.7 V, GND = 0 V, at specified free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VIO
Input offset voltage
αVIO
Average temperature
coefficient of input offset
voltage
IIB
Input bias current
–40°C to
125°C
IIO
Input offset current
–40°C to
125°C
IO
Output current (sinking)
MIN
25°C
VICR
Common-mode input
voltage range
VSAT
Saturation voltage
ICC
Supply current
1.7
7
5
25°C
15
25°C
25°C
Output Leakage Current
MAX
–40°C to
125°C
5
mV
250
nA
50
150
5
UNIT
μV/°C
400
25°C
VO ≤ 1.5 V
TYP
23
nA
mA
0.003
–40°C to
125°C
1
25°C
–0.1 to 2
IO ≤ 1.5 mA
25°C
200
LMV331
25°C
40
100
µA
V
mV
LMV393 (both comparators)
25°C
70
140
LMV339 (all four comparators)
25°C
140
200
μA
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
5
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
6.6 Electrical Characteristics, VCC+ = 5 V
VCC+ = 5 V, GND = 0 V, at specified free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
MIN
25°C
VIO
Input offset voltage
αVIO
Average temperature
coefficient of input offset
voltage
IIB
Input bias current
–40°C to
125°C
IIO
Input offset current
–40°C to
125°C
IO
Output current (sinking)
VO ≤ 1.5 V
1.7
7
9
25°C
5
25°C
25
25°C
2
Common-mode input
voltage range
25°C
AVD
Large-signal differential
voltage gain
25°C
VSAT
Saturation voltage
25°C
IO ≤ 4 mA
84
25°C
mA
1
–0.1 to 4.2
20
200
25°C
–40°C to
125°C
LMV339 (all four comparators)
–40°C to
125°C
25°C
V/mV
400
700
60
µA
V
50
–40°C to
125°C
LMV393 (both comparators)
nA
0.003
–40°C to
125°C
LMV331
nA
50
–40°C to
125°C
VICR
mV
250
150
10
UNIT
μV/°C
400
25°C
Output Leakage Current
Supply current
MAX
–40°C to
125°C
25°C
ICC
TYP
mV
120
150
100
200
250
170
μA
300
350
6.7 Switching Characteristics, VCC+ = 2.7 V
TA = 25°C, VCC+ = 2.7 V, RL = 5.1 kΩ, GND = 0 V (unless otherwise noted)
PARAMETER
6
TEST CONDITIONS
tPHL
Propagation delay high to low level output
switching
tPLH
Propagation delay low to high level output
switching
TYP
Input overdrive = 10 mV
1000
Input overdrive = 100 mV
350
Input overdrive = 10 mV
500
Input overdrive = 100 mV
400
Submit Document Feedback
UNIT
ns
ns
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
6.8 Switching Characteristics, VCC+ = 5 V
TA = 25°C, VCC+ = 5 V, RL = 5.1 kΩ, GND = 0 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TYP
tPHL
Propagation delay high to low level output
switching
Input overdrive = 10 mV
600
Input overdrive = 100 mV
200
tPLH
Propagation delay low to high level output
switching
Input overdrive = 10 mV
450
Input overdrive = 100 mV
300
UNIT
ns
ns
6.9 Typical Characteristics
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0
-40C
25C
85C
Suppply Current (PA)
Suppply Current (PA)
Unless otherwise specified, VS = +5V, single supply, TA = 25°C
1
1.5
2
2.5
3
3.5
Volts (V)
4
4.5
5
Figure 6-1. Supply Current vs Supply Voltage
Output High (LMV33x)
-40C
25C
85C
1
1.5
2
2.5
3
3.5
Volts (V)
4
4.5
5
Figure 6-2. Supply Current vs Supply Voltage
Output Low (LMV33x)
700
55
-40C
25C
85C
650
600
50
550
500
450
400
350
300
250
47.5
45
42.5
40
37.5
35
32.5
200
30
150
27.5
100
0
5
10
15
-40C
25C
85C
52.5
Input Bias Current (nA)
Output Voltage (mV)
95
90
85
80
75
70
65
60
55
50
45
40
35
30
25
20
25
30
35
Output Current (mA)
40
45
50
Figure 6-3. Output Voltage vs Output Current
25
2.4
2.7
3
3.3
3.6 3.9 4.2 4.5
Supply Voltage (V)
4.8
5.1
5.4
5.7
Figure 6-4. Input Bias Current vs Supply Voltage
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
7
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
310
176.1
175.8
305
175.2
295
174.9
Time (ns)
Time (ns)
175.5
300
290
285
174
173.4
275
173.1
270
172.8
265
172.5
0
10
20
30
40
50
60
Overdrive (mV)
70
80
90
0
100
Figure 6-5. Response Time vs Input Overdrives
Negative Transition (VCC=5 V)
648
189
645
188.7
642
188.4
639
188.1
636
187.8
633
630
627
10
20
30
40
50
60
Overdrive (mV)
70
80
90
100
Figure 6-6. Response Time vs Input Overdrives
Positive Transition (VCC = 5 V)
Time (ns)
Time (ns)
174.3
173.7
280
187.5
187.2
186.9
624
186.6
621
186.3
618
186
615
185.7
185.4
612
0
10
20
30
40
50
60
Overdrive (mV)
70
80
90
100
Figure 6-7. Response Time vs Input Overdrives
Negative Transition (VCC = 2.7 V)
8
174.6
0
10
20
30
40
50
60
Overdrive (mV)
70
80
90
100
Figure 6-8. Response Time vs Input Overdrives
Positive Transition (VCC = 2.7 V)
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
7 Detailed Description
7.1 Overview
The LMV331, LMV393 and LMV339 family of comparators have the ability to operate up to 5 V on the supply
pin. This standard device has proven ubiquity and versatility across a wide range of applications. This is due to
it's low Iq and fast response.
The open-drain output allows the user to configure the output's logic low voltage (VOL) and can be utilized to
enable the comparator to be used in AND functionality.
7.2 Functional Block Diagram
VCC+
Q6
Q7
Q8
OUT
IN+
Q1
Q2
Q3
Q4
Q5
Q9
IN−
R1
R3
R2
GND
7.3 Feature Description
The LMV331, LMV393 and LMV339 consists of a PNP input, whose Vbe creates a limit on the input common
mode voltage capability, allowing LMV33x to accurately function from ground to VCC–Vbe(~700mV) differential
input. This enables much head room for modern day supplies of 3.3 V and 5.0 V.
The output consists of an open drain NPN (pull-down or low side) transistor. The output NPN will sink current
when the positive input voltage is higher than the negative input voltage and the offset voltage. The VOL is
resistive and will scale with the output current. Please see Figure 6-3 for VOL values with respect to the output
current.
7.4 Device Functional Modes
7.4.1 Voltage Comparison
The LMV33x operates solely as a voltage comparator, comparing the differential voltage between the positive
and negative pins and outputs a logic low or high impedance (logic high with pull-up) based on the input
differential polarity.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
9
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
8 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
8.1 Application Information
LMV331, LMV393, and LMV339 will typically be used to compare a single signal to a reference or two signals
against each other. Many users take advantage of the open drain output to drive the comparison logic output to
a logic voltage level to an MCU or logic device. The wide supply range and high voltage capability makes
LMV331, LMV393, and LMV33 optimal for level shifting to a higher or lower voltage.
8.2 Typical Application
VLOGIC
VLOGIC
VSUP
Vin
VSUP
Rpullup
+
Vin+
LMV33x
Rpullup
+
LMV33x
Vin-
Vref
CL
CL
Figure 8-1. Typical Application Schematic
8.2.1 Design Requirements
For this design example, use the parameters listed in Table 8-1 as the input parameters.
Table 8-1. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Input Voltage Range
0 V to 4.2 V
Supply Voltage
2.7 V to 5V
Logic Supply Voltage (RPULLUP Voltage)
1 V to 5 V
Output Current (VLOGIC/RPULLUP)
1 µA to 20 mA
Input Overdrive Voltage
100 mV
Reference Voltage
2.5 V
Load Capacitance (CL)
15 pF
8.2.2 Detailed Design Procedure
When using LMV331, LMV393, and LMV33 in a general comparator application, determine the following:
•
•
•
•
10
Input Voltage Range
Minimum Overdrive Voltage
Output and Drive Current
Response Time
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
8.2.2.1 Input Voltage Range
When choosing the input voltage range, the input common mode voltage range (VICR) must be taken in to
account. If operating temperature is above or below 25°C the VICR can range from 0 V to VCC– 0.7 V. This limits
the input voltage range to as high as VCC– 0.7 V and as low as 0 V. Operation outside of this range can yield
incorrect comparisons.
Below is a possible list of input voltage situation and their outcomes:
1. When both IN- and IN+ are both within the common mode range:
a. If IN- is higher than IN+ and the offset voltage, the output is low and the output transistor is sinking current
b. If IN- is lower than IN+ and the offset voltage, the output is high impedance and the output transistor is not
conducting
2. When IN- is higher than common mode and IN+ is within common mode, the output is low and the output
transistor is sinking current
3. When IN+ is higher than common mode and IN- is within common mode, the output is high impedance and
the output transistor is not conducting
4. When IN- and IN+ are both higher than common mode, the output is low and the output transistor is sinking
current
8.2.2.2 Minimum Overdrive Voltage
Overdrive Voltage is the differential voltage produced between the positive and negative inputs of the
comparator over the offset voltage (VIO). In order to make an accurate comparison; the Overdrive Voltage (VOD)
should be higher than the input offset voltage (VIO). Overdrive voltage can also determine the response time of
the comparator, with the response time decreasing with increasing overdrive. Figure 8-2 show positive and
negative response times with respect to overdrive voltage.
8.2.2.3 Output and Drive Current
Output current is determined by the pull-up resistance (Rpullup) and Vlogic voltage, refer to Figure 8-1. The
output current will produce a output low voltage (VOL) from the comparator. In which VOL is proportional to the
output current. Use Figure 6-3 to determine VOL based on the output current.
The output current can also effect the transient response. More will be explained in the next section.
8.2.2.4 Response Time
The transient response can be determined by the load capacitance (CL), load/pull-up resistance (RPULLUP) and
equivalent collector-emitter resistance (RCE).
•
•
The positive response time (τp) is approximately τP ~ RPULLUP × CL
The negative response time (τN) is approximately τN ~ RCE × CL
– RCE can be determine by taking the slope of Figure 6-3 in it's linear region at the desired temperature, or
by dividing the VOL by Iout
8.2.3 Application Curves
The following curves were generated with 5 V on VCC and VLogic, RPULLUP = 5.1 kΩ, and 50 pF scope probe.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
11
LMV331, LMV393, LMV339
www.ti.com
Voltage (V)
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
6
5.5
5
4.5
4
3.5
3
2.5
2
1.5
1
0.5
0
-0.5
-1
0.2
5mV OD
20mV OD
100mV OD
0.22 0.24 0.26 0.28 0.3 0.32 0.34 0.36 0.38
Time (uS)
0.4
Figure 8-2. Response Time for Various Overdrives (Negative Transition)
9 Power Supply Recommendations
For fast response and comparison applications with noisy or AC inputs, it is recommended to use a bypass
capacitor on the supply pin to reject any variation on the supply voltage. This variation cause temporary
fluctuations in the comparator's input common mode range and create an inaccurate comparison.
10 Layout
10.1 Layout Guidelines
For accurate comparator applications without hysteresis it is important maintain a stable power supply with
minimized noise and glitches, which can affect the high level input common mode voltage range. In order to
achieve this, it is best to add a bypass capacitor between the supply voltage and ground. This should be
implemented on the positive power supply and negative supply (if available). If a negative supply is not being
used, do not put a capacitor between the IC's GND pin and system ground.
10.2 Layout Example
Ground
Bypass
Capacitor
0.1 μF
Negative Supply or Ground
Only needed
for dual power
supplies
IN–
1
GND
IN+
3
5
V CC
4
OUT
Positive Supply
2
0.1 μF
Ground
Figure 10-1. LMV331 Layout Example
12
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
LMV331, LMV393, LMV339
www.ti.com
SLCS136U – AUGUST 1999 – REVISED OCTOBER 2020
11 Device and Documentation Support
11.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 11-1. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LMV331
Click here
Click here
Click here
Click here
Click here
LMV393
Click here
Click here
Click here
Click here
Click here
LMV339
Click here
Click here
Click here
Click here
Click here
11.2 Trademarks
All other trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.4 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: LMV331 LMV393 LMV339
13
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
LMV331IDBVR
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R1IF, R1IK)
Samples
LMV331IDBVRE4
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R1IF, R1IK)
Samples
LMV331IDBVRG4
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R1IF, R1IK)
Samples
LMV331IDBVT
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R1IF, R1IK)
Samples
LMV331IDBVTG4
ACTIVE
SOT-23
DBV
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R1IF, R1IK)
Samples
LMV331IDCKR
ACTIVE
SC70
DCK
5
3000
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
(R2F, R2K, R2R)
Samples
LMV331IDCKRE4
ACTIVE
SC70
DCK
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R2F, R2K, R2R)
Samples
LMV331IDCKRG4
ACTIVE
SC70
DCK
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R2F, R2K, R2R)
Samples
LMV331IDCKT
ACTIVE
SC70
DCK
5
250
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
(R2C, R2F, R2R)
Samples
LMV331IDCKTE4
ACTIVE
SC70
DCK
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R2C, R2F, R2R)
Samples
LMV331IDCKTG4
ACTIVE
SC70
DCK
5
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R2C, R2F, R2R)
Samples
LMV339ID
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV339I
Samples
LMV339IDR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV339I
Samples
LMV339IPW
ACTIVE
TSSOP
PW
14
90
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV339I
Samples
LMV339IPWR
ACTIVE
TSSOP
PW
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV339I
Samples
LMV339IPWRG4
ACTIVE
TSSOP
PW
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV339I
Samples
LMV339IRUCR
ACTIVE
QFN
RUC
14
3000
RoHS & Green
NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
(RT, RTR)
Samples
LMV393ID
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV393I
Samples
LMV393IDDUR
ACTIVE
VSSOP
DDU
8
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
RABR
Samples
LMV393IDGKR
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green NIPDAU | NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
(R9B, R9Q, R9R)
Samples
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
LMV393IDGKRG4
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R9B, R9Q, R9R)
Samples
LMV393IDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU | SN
Level-1-260C-UNLIM
-40 to 125
MV393I
Samples
LMV393IDRG4
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV393I
Samples
LMV393IPW
ACTIVE
TSSOP
PW
8
150
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV393I
Samples
LMV393IPWG4
ACTIVE
TSSOP
PW
8
150
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV393I
Samples
LMV393IPWR
ACTIVE
TSSOP
PW
8
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV393I
Samples
LMV393IPWRG4
ACTIVE
TSSOP
PW
8
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV393I
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
