LOG112

OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 Precision, High-Speed Transimpedance Amplifier FEATURES D D D D D D D D D D D D D D D > 1MHz TRANSIMPEDANCE BANDWIDTH EXCELLENT LONG-TERM VOS STABILITY BIAS CURRENT: 50pA (max) OFFSET VOLTAGE: 25µV (max) INPUT CURRENT RANGE: 10nA to 1mA DRIFT: 0.1µV/°C (max) GAIN BANDWIDTH: 90MHz QUIESCENT CURRENT: 6.5mA SUPPLY RANGE: 2.7V to 5.5V SINGLE AND DUAL VERSIONS MicroSize PACKAGE: MSOP-8 DESCRIPTION The OPA380 family of transimpedance amplifiers provides high-speed (90MHz Gain Bandwidth [GBW]) operation, with extremely high precision, excellent long-term stability, and very low 1/f noise. It is ideally suited for high-speed photodiode applications. The OPA380 features an offset voltage of 25µV, offset drift of 0.1µV/°C, and bias current of 50pA. The OPA380 far exceeds the offset, drift, and noise performance that conventional JFET op amps provide. The signal bandwidth of a transimpedance amplifier depends largely on the GBW of the amplifier and the parasitic capacitance of the photodiode, as well as the feedback resistor. The 90MHz GBW of the OPA380 enables a transimpedance bandwidth of > 1MHz in most configurations. The OPA380 is ideally suited for fast control loops for power level on an optical fiber. As a result of the high precision and low-noise characteristics of the OPA380, a dynamic range of 5 decades can be achieved. This capability allows the measurement of signal currents in the order of 10nA, and up to 1mA in a single I/V conversion stage. In contrast to logarithmic amplifiers, the OPA380 provides very wide bandwidth throughout the full dynamic range. By using an external pulldown resistor to –5V, the output voltage range can be extended to include 0V. The OPA380 (single) is available in MSOP-8 and SO-8 packages. The OPA2380 (dual) is available in the miniature MSOP-8 package. They are specified from –40°C to +125°C. APPLICATIONS PHOTODIODE MONITORING PRECISION I/V CONVERSION OPTICAL AMPLIFIERS CAT-SCANNER FRONT-END RF +5V 7 2 OPA380 6 VOUT (0V to 4.4V) Photodiode 1MΩ 67pF −5V 100kΩ 3 75pF RP (Optional Pulldown Resistor) OPA380 RELATED DEVICES PRODUCT OPA300 OPA350 OPA335 OPA132 OPA656/7 LOG112 LOG114 IVC102 DDC112 FEATURES 150MHz CMOS, 2.7V to 5.5V Supply 500µV VOS, 38MHz, 2.5V to 5V Supply 10µV VOS, Zero-Drift, 2.5V to 5V Supply 16MHz GBW, Precision FET Op Amp, ±15V 230MHz, Precision FET, ±5V LOG amp, 7.5 decades, ±4.5V to ±18V Supply LOG amp, 7.5 decades, ±2.25V to ±5.5V Supply Precision Switched Integrator Dual Current Input, 20-Bit ADC 4 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright  2003-2004, Texas Instruments Incorporated www.ti.com OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 www.ti.com ABSOLUTE MAXIMUM RATINGS(1) Voltage Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V Signal Input Terminals(2), Voltage . . . . . . . . . . −0.5V to (V+) + 0.5V Current . . . . . . . . . . . . . . . . . . . . . ±10mA Short-Circuit Current(3) . . . . . . . . . . . . . . . . . . . . . . . . Continuous Operating Temperature Range . . . . . . . . . . . . . . . −40°C to +125°C Storage Temperature Range . . . . . . . . . . . . . . . . . −65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . +300°C ESD Rating (Human Body Model) . . . . . . . . . . . . . . . . . . . . . . . 2000V (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) Input terminals are diode clamped to the power-supply rails. Input signals that can swing more than 0.5V beyond the supply rails should be current limited to 10mA or less. (3) Short-circuit to ground; one amplifier per package. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION(1) PRODUCT OPA380 OPA380 PACKAGE-LEAD MSOP-8 SO-8 PACKAGE MARKING AUN OPA380A OPA2380 MSOP-8 BBX (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet. PIN ASSIGNMENTS Top View OPA380 NC (1) − In +In V− OPA2380 8 7 6 5 NC (1) V+ Out NC (1) 1 2 3 4 MSOP− SO− 8, 8 Out A − In A 1 2 3 4 MSOP− 8 8 7 6 5 V+ Out B − In B +In A V− +In B NOTES: (1) NC indicates no internal connection. 2 www.ti.com OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 ELECTRICAL CHARACTERISTICS: OPA380 (SINGLE), VS = 2.7V to 5.5V Boldface limits apply over the temperature range, TA = −40°C to +125°C. All specifications at TA = +25°C, RL = 2kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted. OPA380 PARAMETER CONDITION MIN TYP MAX UNITS OFFSET VOLTAGE Input Offset Voltage Drift vs Power Supply Over Temperature Long-Term Stability(1) Channel Separation, dc INPUT BIAS CURRENT Input Bias Current Over Temperature Input Offset Current NOISE Input Voltage Noise, f = 0.1Hz to 10Hz Input Voltage Noise Density, f = 10kHz Input Voltage Noise Density, f > 1MHz Input Current Noise Density, f = 10kHz INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio INPUT IMPEDANCE Differential Capacitance Common-Mode Resistance and Inverting Input Capacitance OPEN-LOOP GAIN Open-Loop Voltage Gain VOS dVOS/dT PSRR VS = +5V, VCM = 0V VS = +2.7V to +5.5V, VCM = 0V VS = +2.7V to +5.5V, VCM = 0V 4 0.03 2.4 See Note (1) 1 25 0.1 10 10 µV µV/°C µV/V µV/V µV/V pA pA µVPP nV/√Hz nV/√Hz fA/√Hz IB IOS en en en in VCM CMRR VCM = VS/2 VCM = VS/2 VS = +5V, VCM = 0V VS = +5V, VCM = 0V VS = +5V, VCM = 0V VS = +5V, VCM = 0V V− 100 3 ±50 Typical Characteristics 6 ±100 3 67 5.8 10 (V+) − 1.8V 110 1.1 1013 || 3 (V−) < VCM < (V+) – 1.8V V dB pF Ω || pF AOL 0.1V < VO < (V+) − 0.7V, VS = 5V, VCM = VS/2 0.1V < VO < (V+) − 0.6V, VS = 5V, VCM = VS/2, TA = -40°C to +85°C 0V < VO < (V+) − 0.7V, VS = 5V, VCM = 0V, RP = 2kΩ to −5V(2) 0V < VO < (V+) − 0.6V, VS = 5V, VCM = 0V, RP = 2kΩ to −5V(2), TA = -40°C to +85°C CL = 50pF 110 110 106 106 130 130 120 120 dB dB dB dB FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Settling Time, 0.01%(3) Overload Recovery Time(4)(5) OUTPUT Voltage Output Swing from Positive Rail Voltage Output Swing from Negative Rail Voltage Output Swing from Positive Rail Voltage Output Swing from Negative Rail Output Current Short-Circuit Current Capacitive Load Drive Open-Loop Output Impedance POWER SUPPLY Specified Voltage Range Quiescent Current Over Temperature TEMPERATURE RANGE Specified and Operating Range Storage Range Thermal Resistance MSOP-8, SO-8 GBW SR tS G = +1 VS = +5V, 4V Step, G = +1 VIN • G = > VS RL = 2kΩ RL = 2kΩ RP = 2kΩ to −5V(2) RP = 2kΩ to −5V(2) 90 80 2 100 400 600 60 100 400 600 −20 0 See Typical Characteristics 150 See Typical Characteristics 40 2.7 5.5 8.3 8.8 +125 +150 150 MHz V/µs µs ns mV mV mV mV mA Ω V mA mA °C °C °C/W IOUT ISC CLOAD RO VS IQ f = 1MHz, IO = 0A IO = 0A 6.5 −40 −65 qJA (1) 300-hour life test at 150°C demonstrated randomly distributed variation approximately equal to measurement repeatability of 1µV. (2) Tested with output connected only to R , a pulldown resistor connected between V P OUT and −5V, as shown in Figure 5. See also applications section, Achieving Output Swing to Ground. (3) Transimpedance frequency of 1MHz. (4) Time required to return to linear operation. (5) From positive rail. 3 OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 www.ti.com ELECTRICAL CHARACTERISTICS: OPA2380 (DUAL), VS = 2.7V to 5.5V Boldface limits apply over the temperature range, TA = −40°C to +125°C. All specifications at TA = +25°C, RL = 2kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted. OPA2380 PARAMETER CONDITION MIN TYP MAX UNITS OFFSET VOLTAGE Input Offset Voltage Drift vs Power Supply Over Temperature Long-Term Stability(1) Channel Separation, dc INPUT BIAS CURRENT Input Bias Current, Inverting Input Noninverting Input Over Temperature NOISE Input Voltage Noise, f = 0.1Hz to 10Hz Input Voltage Noise Density, f = 10kHz Input Voltage Noise Density, f > 1MHz Input Current Noise Density, f = 10kHz INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio INPUT IMPEDANCE Differential Capacitance Common-Mode Resistance and Inverting Input Capacitance OPEN-LOOP GAIN Open-Loop Voltage Gain VOS dVOS/dT PSRR VS = +5V, VCM = 0V VS = +2.7V to +5.5V, VCM = 0V VS = +2.7V to +5.5V, VCM = 0V 4 0.03 2.4 See Note (1) 1 25 0.1 10 10 µV µV/°C µV/V µV/V µV/V pA pA IB IB VCM = VS/2 VCM = VS/2 3 ±50 3 ±200 Typical Characteristics 3 67 5.8 10 V− 95 (V+) − 1.8V 105 1.1 1013 || 3 en en en in VCM CMRR VS = +5V, VCM = 0V VS = +5V, VCM = 0V VS = +5V, VCM = 0V VS = +5V, VCM = 0V µVPP nV/√Hz nV/√Hz fA/√Hz V dB pF Ω || pF (V−) < VCM < (V+) – 1.8V AOL 0.12V < VO < (V+) − 0.7V, VS = 5V, VCM = VS/2 0.12V < VO < (V+) − 0.6V, VS = 5V, VCM = VS/2, TA = -40°C to +85°C 0V < VO < (V+) − 0.7V, VS = 5V, VCM = 0V, RP = 2kΩ to −5V(2) 0V < VO < (V+) − 0.6V, VS = 5V, VCM = 0V, RP = 2kΩ to −5V(2), TA = -40°C to +85°C CL = 50pF 110 110 106 106 130 130 120 120 dB dB dB dB FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Settling Time, 0.01%(3) Overload Recovery Time(4), (5) OUTPUT Voltage Output Swing from Positive Rail Voltage Output Swing from Negative Rail Voltage Output Swing from Positive Rail Voltage Output Swing from Negative Rail Output Current Short-Circuit Current Capacitive Load Drive Open-Loop Output Impedance POWER SUPPLY Specified Voltage Range Quiescent Current (per amplifier) Over Temperature TEMPERATURE RANGE Specified and Operating Range Storage Range Thermal Resistance MSOP-8 GBW SR tS G = +1 VS = +5V, 4V Step, G = +1 VIN • G = > VS RL = 2kΩ RL = 2kΩ RP = 2kΩ to −5V(2) RP = 2kΩ to −5V(2) 90 80 2 100 400 600 80 120 400 600 −20 0 See Typical Characteristics 150 See Typical Characteristics 40 2.7 5.5 9.5 10 +125 +150 150 MHz V/µs µs ns mV mV mV mV mA Ω V mA mA °C °C °C/W IOUT ISC CLOAD RO VS IQ f = 1MHz, IO = 0A IO = 0A 7.5 −40 −65 qJA (1) 300-hour life test at 150°C demonstrated randomly distributed variation approximately equal to measurement repeatability of 1µV. (2) Tested with output connected only to R , a pulldown resistor connected between V P OUT and −5V, as shown in Figure 5. See also applications section, Achieving Output Swing to Ground. (3) Transimpedance frequency of 1MHz. (4) Time required to return to linear operation. (5) From positive rail. 4 www.ti.com OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 TYPICAL CHARACTERISTICS: VS = +2.7V to +5.5V All specifications at TA = +25°C, RL = 2kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted. OPEN−LOOP GAIN AND PHASE vs FREQUENCY 140 120 Open− Loop Gain (dB) 100 80 60 40 20 0 − 20 10 100 1k 10k 100k 1M 10M Frequency (Hz) Phase Gain 90 45 PSRR, CMRR (dB) 0 Phase (_ ) − 45 − 90 − 135 − 180 − 225 − 270 100M 160 140 120 100 80 POWER−SUPPLY REJECTION RATIO AND COMMON−MODE REJECTION vs FREQUENCY PSRR 60 40 20 0 − 20 0.1 1 10 100 1k 10k Frequency (Hz) CMRR 100k 1M 10M 100M INPUT VOLTAGE NOISE SPECTRAL DENSITY 1000 Input Voltage Noise (nV/√ (Hz) 8 7 Quiescent Current (mA) 6 5 4 3 2 1 1 10 100 1k 10k 100k 1M 10M Frequency (Hz) 0 QUIESCENT CURRENT vs TEMPERATURE 100 VS = +5.5V VS = +2.7V 10 − 40 − 25 0 25 50 75 100 125 Temperature (_ C) QUIESCENT CURRENT vs SUPPLY VOLTAGE 7 6 Quiescent Current (mA) 5 4 3 2 1 0 2.7 3.0 3.5 4.0 4.5 5.0 5.5 Supply Voltage (V) 1 Input Bias Current (pA) 100 1000 INPUT BIAS CURRENT vs TEMPERATURE 10 − 40 − 25 0 25 50 75 100 125 Temperature (_ C) 5 OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 www.ti.com TYPICAL CHARACTERISTICS: VS = +2.7V to +5.5V (continued) All specifications at TA = +25°C, RL = 2kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted. INPUT BIAS CURRENT vs INPUT COMMON−MODE VOLTAGE 25 20 Input Bias Current (pA) 15 − IB Output Swing (V) 10 5 0 −5 − 10 − 15 − 20 − 25 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 Input Common− Mode Voltage (V) (V− ) 0 + IB (V+) − 1 (V+) − 2 (V− ) +2 (V− ) +1 (V+) OUTPUT VOLTAGE SWING vs OUTPUT CURRENT +125_ C +25_ C − 40_ C 50 100 150 Output Current (mA) SHORT−CIRCUIT CURRENT vs TEMPERATURE 200 VS = 5V Short−Circuit Current (mA) 150 100 50 0 − 50 − 100 − 150 − 40 − 25 Population +ISC OFFSET VOLTAGE PRODUCTION DISTRIBUTION − ISC 0 25 50 75 100 125 − 25 − 20 − 15 − 10 Temperature (_ C) −5 0 5 10 Offset Voltage (µV) 15 20 25 OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 95 GAIN BANDWIDTH vs POWER SUPPLY VOLTAGE Gain Bandwidth (MHz) 90 Population 85 80 75 70 − 0.10 − 0.08 − 0.06 − 0.04 − 0.02 0 0.02 0.04 0.06 0.08 0.1 2.5 3.5 4.5 5.5 Offset Voltage Drift (µV/ _ C) Power Supply Voltage (V) 6 www.ti.com OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 TYPICAL CHARACTERISTICS: VS = +2.7V to +5.5V (continued) All specifications at TA = +25°C, RL = 2kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted. TRANSIMPEDANCE AMP CHARACTERISTIC Circuit for Transimpedance Amplifier Characteristic curves on this page. CF RF CSTRAY Transimpedance Gain (V/A in dB) 140 130 120 110 100 90 80 70 60 50 40 30 R F = 100kΩ RF = 10kΩ RF = 1kΩ RF = 10MΩ RF = 1MΩ CF = 0.5pF CF = 2pF CF = 5pF CF = 18pF CDIODE = 100pF OPA380 CDIODE CSTRAY (parasitic) = 0.2pF 20 100 1k 10k 100k 1M Frequency (Hz) 10M 100M TRANSIMPEDANCE AMP CHARACTERISTIC 140 Transimpedance Gain (V/A in dB) 120 110 100 90 80 70 60 50 40 30 R F = 100kΩ RF = 10kΩ RF = 1kΩ CSTRAY (parasitic) = 0.2pF 1k 10k 100k 1M Frequency (Hz) 10M 100M Transimpedance Gain (V/A in dB) 130 RF = 10MΩ RF = 1MΩ CF = 0.5pF CF = 1.5pF CF = 4pF CF = 12pF CDIODE = 50pF 140 130 120 110 100 90 80 70 60 50 40 30 100 TRANSIMPEDANCE AMP CHARACTERISTIC RF = 10MΩ RF = 1MΩ R F = 100kΩ RF = 10kΩ RF = 1kΩ CSTRAY (parasitic) = 0.2pF 1k 10k 100k 1M Frequency (Hz) 10M 100M CF = 1pF CF = 2.5pF CF = 7pF CDIODE = 20pF 20 100 TRANSIMPEDANCE AMP CHARACTERISTIC 140 Transimpedance Gain (V/A in dB) 120 110 100 90 80 70 60 50 40 30 100 R F = 100kΩ RF = 10kΩ RF = 1kΩ CSTRAY (parasitic) = 0.2pF 1k 10k 100k 1M Frequency (Hz) 10M 100M CF = 0.5pF CF = 2pF CF = 5pF RF = 1MΩ Transimpedance Gain (V/A in dB) 130 RF = 10MΩ CDIODE = 10pF 140 130 120 110 100 90 80 70 60 50 TRANSIMPEDANCE AMP CHARACTERISTIC RF = 10MΩ CDIODE = 1pF RF = 1MΩ R F = 100kΩ RF = 10kΩ CF = 0.5pF RF = 1kΩ CF = 1pF CF = 2.5pF 10M 100M 40 100 CSTRAY (parasitic) = 0.2pF 1k 10k 100k 1M Frequency (Hz) 7 OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 www.ti.com TYPICAL CHARACTERISTICS: VS = +2.7V to +5.5V (continued) All specifications at TA = +25°C, RL = 2kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted. SMALL−SIGNAL OVERSHOOT vs LOAD CAPACITANCE 50 45 10k Ω 2.5pF SMALL−SIGNAL OVERSHOOT vs LOAD CAPACITANCE 50 2.5pF 45 40 +5V RS O PA 38 0 C V OUT RP = 2kΩ −5 V 40 Overshoot (%) Overshoot (%) 35 30 25 20 15 10 5 0 10 100 Load Capacitance (pF) 1000 No RS RS = 100Ω 10kΩ +2.5V RS OPA380 C −2.5V VO U T RF = 2kΩ 35 30 25 20 15 10 5 0 10 No RS RS = 100Ω 100 Load Capacitance (pF) 1000 OVERLOAD RECOVERY 3. 2pF 5 0k Ω SMALL−SIGNAL STEP RESPONSE RL = 2kΩ 2V/div VOUT VP = − 5V I IN 1.6 m A +5V V OUT 2 kΩ VP = 0V 0.8mA/div 0 VP 0 IIN Time (100ns/div) 50mV/div Time (100ns/div) LARGE−SIGNAL STEP RESPONSE RL = 2kΩ Channel Separation (dB) 140 120 100 80 60 40 20 0 Time (100ns/div) 10 CHANNEL SEPARATION vs INPUT FREQUENCY 1V/div 2.5pF 10k Ω 2.5V 2k Ω − 2.5V 100 1k 10k 100k 1M 10M 100M Frequency (Hz) 8 www.ti.com OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 APPLICATIONS INFORMATION BASIC OPERATION The OPA380 is a high-performance transimpedance amplifier with very low 1/f noise. As a result of its unique architecture, the OPA380 has excellent long-term input voltage offset stability—a 300-hour life test at 150°C demonstrated randomly distributed variation approximately equal to measurement repeatability of 1µV. The OPA380 performance results from an internal auto-zero amplifier combined with a high-speed amplifier. The OPA380 has been designed with circuitry to improve overload recovery and settling time over a traditional composite approach. It has been specifically designed and characterized to accommodate circuit options to allow 0V output operation (see Figure 3). The OPA380 is used in inverting configurations, with the noninverting input used as a fixed biasing point. Figure 1 shows the OPA380 in a typical configuration. Power-supply pins should be bypassed with 1µF ceramic or tantalum capacitors. Electrolytic capacitors are not recommended. OPERATING VOLTAGE OPA380 series op amps are fully specified from 2.7V to 5.5V over a temperature range of −40°C to +125°C. Parameters that vary significantly with operating voltages or temperature are shown in the Typical Characteristics. INTERNAL OFFSET CORRECTION The OPA380 series op amps use an auto-zero topology with a time-continuous 90MHz op amp in the signal path. This amplifier is zero-corrected every 100µs using a proprietary technique. Upon power-up, the amplifier requires approximately 400µs to achieve specified VOS accuracy, which includes one full auto-zero cycle of approximately 100µs and the start-up time for the bias circuitry. Prior to this time, the amplifier will function properly but with unspecified offset voltage. This design has virtually no aliasing and very low noise. Zero correction occurs at a 10kHz rate, but there is very little fundamental noise energy present at that frequency due to internal filtering. For all practical purposes, any glitches have energy at 20MHz or higher and are easily filtered, if required. Most applications are not sensitive to such high-frequency noise, and no filtering is required. CF RF +5V 1µ F INPUT VOLTAGE The input common-mode voltage range of the OPA380 series extends from V− to (V+) –1.8V. With input signals above this common-mode range, the amplifier will no longer provide a valid output value, but it will not latch or invert. λ OPA380 VOUT(1) (0.5V to 4.4V) INPUT OVERVOLTAGE PROTECTION VBIAS = 0.5V NOTE: (1) VOUT = 0.5V in dark conditions. Figure 1. OPA380 typical configuration Device inputs are protected by ESD diodes that will conduct if the input voltages exceed the power supplies by more than approximately 500mV. Momentary voltages greater than 500mV beyond the power supply can be tolerated if the current is limited to 10mA. The OPA380 series feature no phase inversion when the inputs extend beyond supplies if the input is current limited. 9 OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 www.ti.com OUTPUT RANGE The OPA380 is specified to swing within at least 600mV of the positive rail and 100mV of the negative rail with a 2kΩ load with excellent linearity. Swing to the negative rail while maintaining good linearity can be extended to 0V—see the section, Achieving Output Swing to Ground. See the Typical Characteristic curve, Output Voltage Swing vs Output Current. The OPA380 can swing slightly closer than specified to the positive rail; however, linearity will decrease and a high-speed overload recovery clamp limits the amount of positive output voltage swing available—see Figure 2. ACHIEVING OUTPUT SWING TO GROUND Some applications require output voltage swing from 0V to a positive full-scale voltage (such as +4.096V) with excellent accuracy. With most single-supply op amps, problems arise when the output signal approaches 0V, near the lower output swing limit of a single-supply op amp. A good single-supply op amp may swing close to single-supply ground, but will not reach 0V. The output of the OPA380 can be made to swing to ground, or slightly below, on a single-supply power source. This extended output swing requires the use of another resistor and an additional negative power supply. A pulldown resistor may be connected between the output and the negative supply to pull the output down to 0V. See Figure 3. OFFSET VOLTAGE vs OUTPUT VOLTAGE 20 VS = 5V 15 10 VOS (µV) 5 0 −5 RL = 2kΩ connected to VS /2 Effect of clamp RP = 2kΩ V− = Gnd 0 1 2 VOUT (V) 3 4 5 VP = − 5V Negative Supply λ V+ = +5V RP = 2kΩ connected to − 5V RF −10 −15 −20 OPA380 VOUT Figure 2. Effect of high-speed overload recovery clamp on output voltage OVERLOAD RECOVERY The OPA380 has been designed to prevent output saturation. After being overdriven to the positive rail, it will typically require only 100ns to return to linear operation. The time required for negative overload recovery is greater, unless a pulldown resistor connected to a more negative supply is used to extend the output swing all the way to the negative rail—see the following section, Achieving Output Swing to Ground. Figure 3. Amplifier with optional pull-down resistor to achieve VOUT = 0V The OPA380 has an output stage that allows the output voltage to be pulled to its negative supply rail using this technique. However, this technique only works with some types of output stages. The OPA380 has been designed to perform well with this method. Accuracy is excellent down to 0V. Reliable operation is assured over the specified temperature range. 10 www.ti.com OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 BIASING PHOTODIODES IN SINGLE-SUPPLY CIRCUITS The +IN input can be biased with a positive DC voltage to offset the output voltage and allow the amplifier output to indicate a true zero photodiode measurement when the photodiode is not exposed to any light. It will also prevent the added delay that results from coming out of the negative rail. This bias voltage appears across the photodiode, providing a reverse bias for faster operation. An RC filter placed at this bias point will reduce noise. (Refer to Figure 4.) This bias voltage can also serve as an offset bias point for an ADC with range that does not include ground. the desired transimpedance gain (RF); the Gain Bandwidth Product (GBW) for the OPA380 (90MHz). With these three variables set, the feedback capacitor value (CF) can be set to control the frequency response. CSTRAY is the stray capacitance of RF, which is 0.2pF for a typical surface-mount resistor. To achieve a maximally flat 2nd-order Butterworth frequency response, the feedback pole should be set to: 1 + 2pR F CF ) CSTRAY GBW 4pR FC TOT (1) Bandwidth is calculated by: CF(1) < 1pF f *3dB + GBW Hz 2pRFC TOT (2) RF 10MΩ V+ λ These equations will result in maximum transimpedance bandwidth. For even higher transimpedance bandwidth, the high-speed CMOS OPA300 (180MHz GBW), or the OPA656 (230MHz GBW) may be used. VOUT OPA380 0.1µ F 100kΩ For additional information, refer to Application Bulletin AB−050 (SBOA055), Compensate Transimpedance Amplifiers Intuitively, available for download at www.ti.com . +VBias NOTE: (1) CF is optional to prevent gain peaking. It includes the stray capacitance of RF. CF(1) RF 10MΩ Figure 4. Filtered reverse bias voltage CSTRAY(2) +5V λ CTOT(3) OPA380 TRANSIMPEDANCE AMPLIFIER Wide bandwidth, low input bias current, and low input voltage and current noise make the OPA380 an ideal wideband photodiode transimpedance amplifier. Low voltage noise is important because photodiode capacitance causes the effective noise gain of the circuit to increase at high frequency. The key elements to a transimpedance design are shown in Figure 5: the total input capacitance (CTOT), consisting of the photodiode capacitance (CDIODE) plus the parasitic common-mode and differential-mode input capacitance (3pF + 1.1pF for the OPA380); VOUT RP (optional pulldown resistor) − 5V NOTE: (1) CF is optional to prevent gain peaking. (2) CSTRAY is the stray capacitance of RF (typically, 0.2pF for a surface− mount resistor). (3) CTOT is the photodiode capacitance plus OPA380 input capacitance. Figure 5. Transimpedance Amplifier 11 OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 www.ti.com TRANSIMPEDANCE BANDWIDTH AND NOISE Limiting the gain set by RF can decrease the noise occurring at the output of the transimpedance circuit. However, all required gain should occur in the transimpedance stage, since adding gain after the transimpedance amplifier generally produces poorer noise performance. The noise spectral density produced by RF increases with the square-root of RF, whereas the signal increases linearly. Therefore, signal-to-noise ratio is improved when all the required gain is placed in the transimpedance stage. Total noise increases with increased bandwidth. Limit the circuit bandwidth to only that required. Use a capacitor, CF, across the feedback resistor, RF, to limit bandwidth, even if not required for stability if total output noise is a concern. Figure 6a shows the transimpedance circuit without any feedback capacitor. The resulting transimpedance gain of this circuit is shown in Figure 7. The –3dB point is approximately 10MHz. Adding a 16pF feedback capacitor (Figure 6b) will limit the bandwidth and result in a –3dB point at approximately 1MHz (seen in Figure 7). Output noise will be further reduced by adding a filter (RFILTER and CFILTER) to create a second pole (Figure 6c). This second pole is placed within the feedback loop to maintain the amplifier’s low output impedance. (If the pole was placed outside the feedback loop, an additional buffer would be required and would inadvertently increase noise and dc error). Using RDIODE to represent the equivalent diode resistance, and CTOT for equivalent diode capacitance plus OPA380 input capacitance, the noise zero, fZ, is calculated by: fZ + RDIODE ) RF 2pRDIODER F C TOT ) C F (a) R F = 10kΩ C STRAY = 0.2pF λ O PA380 VOUT VBIAS (b) RF = 10kΩ CSTRAY = 0.2pF CF = 16pF λ OPA380 VOUT VBIAS (c) RF = 10kΩ CSTRAY = 0.2pF CF = 21pF R FILTER = 100Ω OPA380 λ VOUT CFILTER = 796pF (3) VBIAS Figure 6. Transimpedance circuit configurations with varying total and integrated noise gain 12 www.ti.com OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 110 Transimpedance Gain (dB) See Figure 6a Integrated Output Noise (µVrms) CDIODE = 10pF 500 CDIODE = 10pF See Figure 6a 419µV 80 − 3dB BW at 1MHz 50 See Figure 6c 400 300 200 See Figure 6b 100 See Figure 6c 86µV 30µV 20 See Figure 6b − 10 100 0 1k 10k 100k Frequency (Hz) 1M 10M 100M 1 10 100 1k 10k 100k Frequency (Hz) 1M 10M 100M Figure 7. Transimpedance gains for circuits in Figure 6 The effect of these circuit configurations on output noise is shown in Figure 8 and on integrated output noise in Figure 9. A 2-pole Butterworth filter (maximally flat in passband) is created by selecting the filter values using the equation: C FRF + 2C FILTERR FILTER with: 2p RFR FILTERCFC FILTER (4) Figure 9. Integrated output noise for circuits in Figure 6 Figure 10 shows the effect of diode capacitance on integrated output noise, using the circuit in Figure 6c. For additional information, refer to Noise Analysis of FET Transimpedance Amplifiers (SBOA060), and Noise Analysis for High Speed Op Amps (SBOA066), available for download from the TI web site. (5) Integrated Output Noise (µVrms) f *3dB + 1 79µV 80 CDIODE = 100pF CDIODE = 50pF CDIODE = 20pF 50µV 35µV 30µV 27µV 20 See Figure 6c CDIODE = 10pF 1k 10k 100k Frequency (Hz) 1M CDIODE = 1pF 10M 100M The circuit in Figure 6b rolls off at 20dB/decade. The circuit with the additional filter shown in Figure 6c rolls off at 40dB/decade, resulting in improved noise performance. 60 0 300 CDIODE = 10pF 0 1 10 100 Output Noise (nV/ √ Hz) 200 See Figure 6a Figure 10. Integrated output noise for various values of CDIODE for circuit in Figure 6c 100 See Figure 6b See Figure 6c 0 1 10 100 1k 10k 100k 1M 10M 100M Frequency (Hz) Figure 8. Output noise for circuits in Figure 6 13 OPA380 OPA2380 SBOS291E − NOVEMBER 2003 − REVISED NOVEMBER 2004 www.ti.com BOARD LAYOUT Minimize photodiode capacitance and stray capacitance at the summing junction (inverting input). This capacitance causes the voltage noise of the op amp to be amplified (increasing amplification at high frequency). Using a low-noise voltage source to reverse-bias a photodiode can significantly reduce its capacitance. Smaller photodiodes have lower capacitance. Use optics to concentrate light on a small photodiode. Circuit board leakage can degrade the performance of an otherwise well-designed amplifier. Clean the circuit board carefully. A circuit board guard trace that encircles the summing junction and is driven at the same voltage can help control leakage. See Figure 11. One method of improving capacitive load drive in the unity-gain configuration is to insert a 10Ω to 20Ω resistor in series with the load. This reduces ringing with large capacitive loads while maintaining DC accuracy. DRIVING FAST 16-BIT ANALOG-TO-DIGITAL CONVERTERS (ADC) The OPA380 series is optimized for driving a fast 16-bit ADC such as the ADS8411. The OPA380 op amp buffers the converter’s input capacitance and resulting charge injection while providing signal gain. Figure 12 shows the OPA380 in a single-ended method of interfacing the ADS8411 16-bit, 2MSPS ADC. For additional information, refer to the ADS8411 data sheet. RF CF λ OPA380 VOUT RF 15Ω OPA380 ADS8411 6800pF Guard ring Figure 11. Connection of input guard OTHER WAYS TO MEASURE SMALL CURRENTS Logarithmic amplifiers are used to compress extremely wide dynamic range input currents to a much narrower range. Wide input dynamic ranges of 8 decades, or 100pA to 10mA, can be accommodated for input to a 12-bit ADC. (Suggested products: LOG101, LOG102, LOG104, LOG112.) Extremely small currents can be accurately measured by integrating currents on a capacitor. (Suggested product: IVC102.) Low-level currents can be converted to high-resolution data words. (Suggested product: DDC112.) For further information on the range of products available, search www.ti.com using the above specific model names or by using keywords transimpedance and logarithmic. RC Values shown are optimized for the ADS8411 values may vary for other ADCs. Figure 12. Driving 16-bit ADCs CF RF R1 VIN OPA380 VOUT (Provides high−speed amplification with very low offset and drift.) CAPACITIVE LOAD AND STABILITY The OPA380 series op amps can drive up to 500pF pure capacitive load. Increasing the gain enhances the amplifier’s ability to drive greater capacitive loads (see the Typical Characteristic curve, Small Signal Overshoot vs Capacitive Load). 14 Figure 13. OPA380 inverting gain configuration PACKAGE OPTION ADDENDUM www.ti.com 9-Dec-2004 PACKAGING INFORMATION Orderable Device OPA2380AIDGKR OPA2380AIDGKT OPA380AID OPA380AIDGKR OPA380AIDGKT OPA380AIDR (1) Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type MSOP MSOP SOIC MSOP MSOP SOIC Package Drawing DGK DGK D DGK DGK D Pins Package Eco Plan (2) Qty 8 8 8 8 8 8 2500 Green (RoHS & no Sb/Br) 250 100 2500 250 2500 Green (RoHS & no Sb/Br) None None None None Lead/Ball Finish CU NIPDAU CU NIPDAU CU SNPB CU NIPDAU CU NIPDAU CU SNPB MSL Peak Temp (3) Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-1-220C-UNLIM Level-1-220C-UNLIM Level-1-220C-UNLIM Level-1-220C-UNLIM The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright  2004, Texas Instruments Incorporated www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless