User's Guide
SBOU110 – September 2011
LOG114EVM User Guide
This user's guide describes the characteristics, operation, and use of the LOG114EVM evaluation board. It
discusses how to set up and configure the board hardware, and reviews various methods of using the
evaluation module (EVM). Throughout this document, the terms evaluation board, evaluation module, and
EVM are synonymous with the LOG114EVM. This document also includes an electrical schematic, printed
circuit board (PCB) layout drawings, and a parts list for the EVM.
1
2
3
4
5
6
Contents
Overview ..................................................................................................................... 2
LOG114EVM ................................................................................................................ 3
Connecting to the LOG114EVM .......................................................................................... 7
Using the LOG114EVM ................................................................................................... 11
Verifying Results ........................................................................................................... 12
LOG114EVM Documentation ............................................................................................ 13
List of Figures
................................................................................................................
1
LOG114EVM
2
LOG114EVM Level Shifter................................................................................................. 3
3
LOG114EVM Signal Path .................................................................................................. 4
4
High-Current Linearity Correction Circuit ................................................................................ 5
5
LOG114EVM Complete Circuit ............................................................................................ 6
6
Connecting the 5V Power Supply ......................................................................................... 7
7
Using a Photodiode with the High-Current Linearity Correction Circuitry
8
9
10
11
12
13
14
15
16
17
2
........................................... 7
Using a Photodiode Without the High-Current Linearity Correction Circuitry ....................................... 8
Applying a 0.5-V Reverse Bias to the Photodiode...................................................................... 8
Using a Resistor to Create an Input Current ............................................................................ 9
Using a Resistor and the High Current Linearity Correction Circuitry .............................................. 10
LOG114EVM Components ............................................................................................... 11
LOG114EVM Measured Results ........................................................................................ 12
LOG114EVM Board Schematic.......................................................................................... 13
LOG114EVM: Top Side Composite Drawing .......................................................................... 14
LOG114EVM: Top Copper Layer ....................................................................................... 14
LOG114EVM: Bottom Copper Layer .................................................................................... 14
All trademarks are the property of their respective owners.
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
1
Overview
1
www.ti.com
Overview
The LOG114 is a single-supply, high-speed, precision logarithmic amplifier. This device computes the
logarithm or log-ratio of an input current or voltage relative to a reference current or voltage. The
LOG114EVM (shown in Figure 1) is a ready-to-use platform for evaluating the performance of the
LOG114 in various configurations. This document gives a general overview of the LOG114EVM, and
provides a general description of the features and functions to be considered while using this evaluation
module.
Figure 1. LOG114EVM
1.1
Getting Started
Tested at the factory over a wide range of input currents, the LOG114EVM comes ready to use and
includes this Quick Start User’s Guide. Use of the LOG114EVM requires a 5-V power source, an input
source such as a photodiode or resistor, and a digital voltmeter or oscilloscope.
1.2
Related Documentation from Texas Instruments
The following documents provide information regarding Texas Instruments' integrated circuits and support
tools for the LOG114EVM. This user's guide is available from the TI web site under literature number
SBOU110. Any letter appended to the literature number corresponds to the document revision that is
current at the time of the writing of this document. Newer revisions may be available from the TI web site,
or call the Texas Instruments' Literature Response Center at (800) 477-8924 or the Product Information
Center at (972) 644-5580. When ordering, identify the document by both title and literature number.
Related Documentation
Document
2
Literature Number
LOG114 Product Data Sheet
SBOS301
LOG114 TINA-TI Reference Design
SBOM384B
LOG114 TINA-TI Spice Model
SBOM385B
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM
www.ti.com
2
LOG114EVM
The LOG114EVM comes completely assembled and constructed to operate on a single 5-V power supply.
The circuit used in the LOG114EVM is designed to operate over a wide range of input currents (10 nA to
10 mA) and scales the output voltage from 1.15 V to 2.75 V. There are three distinct sections to the
LOG114EVM circuit: a precision level shifter, the signal path, and the high-current linearity correction
section. Each section is described below to familiarize you with the circuit functionality and operation.
2.1
Level Shifter
A precision level shifter is required to operate the LOG114 on a single power supply. On the
LOG114EVM, the level shifter circuit is constructed by deriving a bias voltage of 2 V from the 2.5-V
voltage reference internal to the LOG114. This level shift of 2 V is required to keep the nodes internal to
the LOG114 properly biased when operating from a single power supply. Resistors R9 and R10 form a
voltage divider that is then buffered by the OPA365 amplifier. The output of the OPA365 is a fixed voltage
of 2 V, independent of the power-supply voltage or input signal. C2 is used to bypass the power supply for
the OPA365. The level shifter circuit is shown in Figure 2.
2.5 V
from LOG114 VREF
+
C2
100 nF
R10
1 kW
R9
4.02 kW
OPA365
VCC
+5 V
VBIAS
Figure 2. LOG114EVM Level Shifter
2.2
Signal Path
The LOG114 has two inputs, I1 and I2. Input I1 is used for the input signal (usually from a photodiode) and
I2 is a fixed-current reference signal. This fixed-current reference signal is derived from the 2.5-V voltage
reference internal to the LOG114 and the 2-V output from the level shifter. The reference current into I2 is
given by Equation 1.
(2.5 V - 2 V)
IREF =
= 500 nA
1 MW
(1)
The input current must flow into I1 and comes directly from the anode of a photodiode. In non-optical
applications, the input current could also be derived from a resistor, or a variety of other sources (see
Section 3.4). For proper operation, each input to the LOG114 (I1 and I2) requires the current to flow into
the LOG114.
The output from the LOG114 amplifier A3 is called VLOGOUT. The relationship between VLOGOUT, I1 and I2,
and the bias voltage generated by the level shifter is described by Equation 2.
I
VLOGOUT = 0.375·LOG10 2 + 2 V
I1
(2)
( (
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
3
LOG114EVM
www.ti.com
The VLOGOUT output is then scaled by resistors R7 and R8. These resistors divide the signal before
combining with the high-current linearity correction section. Combining the input signal and linearity
correction signal is accomplished with amplifier A4 and resistors R5 and R6. Capacitor C1 is used to
bypass the power supply for the LOG114. The signal path circuit is shown in Figure 3.
High-Current Linearity
Correction Signal
VLOGOUT
VCC
5V
+
R7
10 kW
C1
100 nF
R8
4.3 kW
IREF
R11
1 MW
VREF
R6
10 kW
R5
10 kW
V+
IPHOTO
VREF
VBIAS
(from the
Level Shifter)
A4
A1
VOUT
A3
A5
A2
V-
Figure 3. LOG114EVM Signal Path
2.3
High-Current Linearity Correction
The LOG114 is capable of handling a wide dynamic range of currents, from less than 100 pA in a carefully
designed PCB to 10 mA in high-current applications. Because the LOG114 was designed for high speeds,
the transistors that provide feedback around amplifiers A1 and A2 within the LOG114 have a small series
resistance, RS. This small series resistance causes a deviation from the ideal LOG114 transfer function at
input currents that exceed approximately 1 mA. The modified equation for VLOGOUT that shows this
deviation from the ideal is given in Equation 3.
I
VLOGOUT = 0.375·LOG10 2 + 2 V + I1·RS
I1
(3)
( (
4
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM
www.ti.com
The high-current linearity correction circuit (refer to Figure 4) creates an error signal that is proportional to
input current I1 by using R2, R3 and R4, and amplifier A5. Resistor R1 is used to properly level-shift the
resulting output signal. The signal at the output from amplifier A5 is then coupled to the input of amplifier
A4 in a manner that subtracts the error signal from the output of the EVM, VOUT.
VBIAS
(from the Level Shifter)
V+
R2
3W
IPHOTO
VREF
A4
A1
VERR
A3
A5
A2
V-
R4
5 kW
R3
1 kW
R2
21.5 kW
Figure 4. High-Current Linearity Correction Circuit
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
5
LOG114EVM
www.ti.com
Figure 5 shows the entire circuit layout of the LOG114EVM.
VERR
VLOGOUT
VLOG
+
R7
10 kW
VCC
5V
R8
4.3 kW
IREF
R11
1 MW
VREF
C1
100 nF
R6
10 kW
R5
10 kW
V+
IPHOTO
R2
3W
VREF
A4
A1
VOUT
VREF
A3
C2
100 nF
R10
1 kW
VERR
A5
A2
R9
4.02 kW
OPA365
VR4
5 kW
VBIAS
R1
21.5 kW
R3
1 kW
Figure 5. LOG114EVM Complete Circuit
6
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
SBOU110 – September 2011
Submit Documentation Feedback
Connecting to the LOG114EVM
www.ti.com
3
Connecting to the LOG114EVM
The LOG114 requires only a few connections to operate: a 5-V power supply, an input source such as a
photodiode or resistor, and a digital voltmeter or oscilloscope.
3.1
Electrostatic Discharge Warning
CAUTION
Many of the components on the LOG114EVM are susceptible to damage by
electrostatic discharge (ESD). Customers are advised to observe proper ESD
handling precautions when unpacking and handling the EVM, including the use
of a grounded wrist strap at an approved ESD workstation.
3.2
Basic Connections
The connections for 5 V and ground are clearly marked on the LOG114EVM PCB. Figure 6 shows how to
properly connect the power supply to the connector.
+
+5 V
Figure 6. Connecting the 5V Power Supply
3.3
Using a Photodiode
An anode of a photodiode can be connected to the LOG114 by either using the pads or pin sockets on the
LOG114EVM. To use the high-current linearity correction circuitry, connect the photodiode as illustrated in
Figure 7.
Figure 7. Using a Photodiode with the High-Current Linearity Correction Circuitry
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
7
Connecting to the LOG114EVM
www.ti.com
Figure 8 shows the connections required to bypass the high-current linearity circuitry. This connection
results in placing zero bias across the photodiode.
Figure 8. Using a Photodiode Without the High-Current Linearity Correction Circuitry
A 0.5-V reverse bias can be easily placed across the photodiode by connecting the photodiode as shown
in Figure 9. When connecting the photodiode in this configuration, the high-current linearity correction
circuitry is bypassed.
Figure 9. Applying a 0.5-V Reverse Bias to the Photodiode
8
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
SBOU110 – September 2011
Submit Documentation Feedback
Connecting to the LOG114EVM
www.ti.com
3.4
Using a Resistor
Using a resistor instead of a photodiode to create an input current is quite simple. As Figure 10 shows, a
1-MΩ resistor is placed between VREF and the input I1. In this case, the input current I1 is determined by
Equation 4.
(V - VBIAS)
I1 = REF
R
(4)
Figure 10. Using a Resistor to Create an Input Current
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
9
Connecting to the LOG114EVM
www.ti.com
In the case where I1 = 500 nA = IREF, the VLOGOUT terminal is equal to the level shifting bias voltage of 2 V
and the VOUT terminal is equal to 1.5 V. The circuit in Figure 10, while convenient for creating an input
current, does not take advantage of the high-current linearity correction circuitry. To use this circuitry, a
second power supply must be used and configured as shown in Figure 11.
+
+ VIN
Figure 11. Using a Resistor and the High Current Linearity Correction Circuitry
Changing the input voltage or the resistor value changes the input current I1 (I1 = VIN/R) and results in a
change for the VLOGOUT terminal voltage according to Equation 5.
I
VLOGOUT = 0.375·LOG10 2 + 2 V + I1·50 W
I1
(5)
( (
For input currents less than 1 mA, this equation simplifies to Equation 2.
The voltage at the VLOG terminal is given by Equation 6:
I
VLOG = [0.375·LOG10 2 + I1·50 W] · 0.3 V/V + 2 V
I1
( (
(6)
The voltage at the VERR terminal is given by Equation 7:
VERR = 2 +
(I1·3)
2
+
1 kW 21.5 kW
· 5 kW
(7)
The voltage at the VOUT terminal is given by Equation 8:
VOUT = 2·VLOG - VERR
10
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
(8)
SBOU110 – September 2011
Submit Documentation Feedback
Using the LOG114EVM
www.ti.com
4
Using the LOG114EVM
Once the LOG114EVM has power applied and an input signal, easy access terminal pins allow for quickly
evaluating the circuit performance. Connect a digital voltmeter or oscilloscope to any of the terminals to
make the measurements. Figure 12 is a reference guide to the LOG114EVM and its related components.
VREF = 2.5 V
VERR
VOUT
VLOG
High Current
Error Protection
Input
VOUT
Input I1
Ground
5V
Ground
VBIAS = 2.0 V
5V
Ground
VLOGOUT
Figure 12. LOG114EVM Components
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
11
Verifying Results
5
www.ti.com
Verifying Results
Making measurements on the LOG114EVM is fast and easy. Connect a digital voltmeter or oscilloscope to
the terminal of interest and record the results. Included with the graph of measured results is a table of
results for common values of input currents. In Figure 13, two curves are shown. Both curves use a
resistor input and VOUT is recorded as a function of input current. The compensated (red) curve connects
the resistor as shown in Figure 11 and uses the high-current linearity correction circuitry. The
uncompensated curve (blue) uses the resistor connected to I1 and VREF as shown in Figure 10.
3
Output Voltage (V)
Uncompensated Output
Compensated Output
2.5
2
1.5
1
10n
100n
1m
10m
100m
Input Current (A)
1m
10m
Figure 13. LOG114EVM Measured Results
Table 1 lists several typical results obtained with various input voltages.
Table 1. LOG114EVM Typical Results
Uncompensated
12
Compensated
Input
VLOGOUT (V)
VOUT (V)
VLOGOUT (V)
VOUT (V)
10 nA
1.36
1.15
1.36
1.15
100 nA
1.74
1.38
1.74
1.38
1 μA
2.11
1.60
2.11
1.60
10 μA
2.49
1.83
2.49
1.83
100 μA
2.87
2.06
2.87
2.06
1 mA
3.29
2.31
3.29
2.30
10 mA
4.11
2.82
4.11
2.67
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM Documentation
www.ti.com
6
LOG114EVM Documentation
This section contains the complete bill of materials and PCB layout for the LOG114EVM.
NOTE: These board layouts are not to scale. These image are intended to show how the board is
laid out; they are not intended to be used for manufacturing LOG114EVM PCBs.
6.1
Schematic
-IN5
TP7
BNC_VERT
R6
10k
Figure 14 shows the schematic for the LOG114EVM board
TP2
VERR
R4
TP3
Vout
TP8
Vref
Vref
V+
Com
Vbias
R8
4.27k
TP1
R1
21.3k
Vcc
T_STRIP2
GND
T1
1
2
TP5
Vcc
C7
4.7uF
VCC
C3
1uF
TP6
GND
-IN5
1k
Vbias
R2 R10 R9
6
1k 4.02k
5
2
D1
PIPD
4
1
6
3
R3
V
ref
C2
100n
+
VCC
U2
OPA365
Vlog
VCC
8
7
6
5
4
I2
3
2
1
C1
V-
Vcm_IN
I1
I2
100n
Vo_5
-IN5
+IN5
Vo_4
-IN4
+IN4
NC
Vref_GND Vlogout
GND
17
U1
LOG114
I2
16
14
15
R11
1M
Vbias
12
11
13
10k
9
10
R7
TP4
Vlog
V
ref
TP9
Vlogout
5k
R5
Vlog
10k
1
2
Figure 14. LOG114EVM Board Schematic
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
13
LOG114EVM Documentation
6.2
www.ti.com
PCB Layout
Figure 15 through Figure 17 show the PCB layout of the LOG114EVM.
Figure 15. LOG114EVM: Top Side Composite Drawing
Figure 16. LOG114EVM: Top Copper Layer
Figure 17. LOG114EVM: Bottom Copper Layer
14
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
SBOU110 – September 2011
Submit Documentation Feedback
LOG114EVM Documentation
www.ti.com
6.3
Bill of Materials
Table 2 lists the bill of materials for the LOG114EVM
Table 2. LOG114 Bill of Materials
Item No
Count
Value
Ref Des
1
1
21.5 kΩ
R1
Resistor, 21.5 kΩ 1/10W 1% 0603 SMD
Yageo
RC0603FR-0721K5L
2
1
3Ω
R2
Resistor, 3.0 Ω 1/10W 5% 0603
Panasonic - ECG
ERJ-3GEYJ3R0V
3
2
1 kΩ
R3, R10
Resistor, 1.0 kΩ .25W 5% 0603 SMD
Vishay/Dale
CRCW06031K00JNEAHP
4
1
4.99 kΩ
R4
Resistor, 4.99 kΩ 1/10W 1% 0603 SMD
Panasonic
ERJ-3EKF4991V
5
3
10 kΩ
R5, R6, R7
Resistor, 10.0 kΩ 1/10W 1% 0603 SMD
Panasonic
ERJ-3EKF1002VRES
6
1
4.3 kΩ
R8
Resistor, 4.3 kΩ 1/16W .5% 0603 SMD
Susumu
RR0816P-432-D
7
1
4.02 kΩ
R9
Resistor, 4.02 kΩ 1/10W 1% 0603 SMD
Panasonic
ERJ-3EKF4021V
8
1
1 MΩ
R11
Resistor, 1.00 MΩ 1/10W 1% 0603 SMD
Panasonic
ERJ-3EKF1004V
9
1
4.7 μF
C7
Capacaitor, Tantalum 4.7 μF 35V 10% SM
AVX Corporation
TAJC475K035RNJ
10
1
0.1 μF
C3
Capacaitor, Ceramic .100 μF 25V X7R 0603
Yageo
CC0603KRX7R8BB104
11
2
100 nF
C1, C2
Capacaitor, Ceramic 1000 pF 25V Y5V 0603
Murata Electronics
North America
GRM188F51E102ZA01D
12
1
—
U1
LOG114
Texas Instruments
LOG114AIRGVT
13
1
—
U2
OPA365
Texas Instruments
OPA365AIDBVR
14
1
BNC
TP7
Connector, Jack BNC Vert 50 Ω
Tyco Electronics
5227699-1
15
1
—
T1
PCB Terminal Block 5 MM 2-Pos
On-Shore Technology ED300/2
Inc
16
9
N/A
Test Points,
All
Connector, Header 1-Pos .100" Sgl Gold
Samtec
TSW-101-07-G-S
17
4
Standoff
—
Standoffs, Hex , 4-40 Threaded, 0.500-in.
length, 0.250-in OD, Aluminum Iridite Finish
Keystone
2203
18
4
Screw
—
Screw, Machine, Phillips 4-40x1/4 SS
B & F Fastener
Supply
PMSSS 440 0025 PH
19
1
N/A
D1
Do not install
SBOU110 – September 2011
Submit Documentation Feedback
Description
MFR
—
Mfr Part Number
—
LOG114EVM User Guide
Copyright © 2011, Texas Instruments Incorporated
15
Evaluation Board/Kit Important Notice
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION
PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the
product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are
not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations,
including product safety and environmental measures typically found in end products that incorporate such semiconductor
components or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regarding
electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the
technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30
days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY
SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all
claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to
take any and all appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER
FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of
patents or services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the
product. This notice contains important safety information about temperatures and voltages. For additional information on TI’s
environmental and/or safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION
PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and
can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15
of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this
equipment in other environments may cause interference with radio communications, in which case the user at his own expense
will be required to take whatever measures may be required to correct this interference.
EVM Warnings and Restrictions
It is important to operate this EVM within the input voltage range of ±2.4V to ± 5.5 V and the output voltage range of ±1.8 V to ±4.9
V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are
questions concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the
EVM. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load
specification, please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than +25°C. The EVM is designed to
operate properly with certain components above +25°C as long as the input and output ranges are maintained. These components
include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of
devices can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near
these devices during operation, please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of this Product in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even
if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
