LP339DG4




    
    The LP239 is obsolete and is no longer supplied. SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004 D Wide Supply-Voltage Range . . . 3 V to 30 V D Ultralow Power Supply Current D D D D D D D D D D OR N PACKAGE (TOP VIEW) Drain . . . 60 µA Typ Low Input Biasing Current . . . 3 nA Low Input Offset Current . . . ±0.5 nA Low Input Offset Voltage . . . ±2 mV Common-Mode Input Voltage Includes Ground Output Voltage Compatible With MOS and CMOS Logic High Output Sink-Current Capability (30 mA at VO = 2V) Power Supply Input Reverse-Voltage Protected Single-Power-Supply Operation Pin-for-Pin Compatible With LM239, LM339, LM2901 1OUT 2OUT VCC 2IN − 2IN + 1IN − 1IN + 1 14 2 13 3 12 4 11 5 10 6 9 7 8 3OUT 4OUT GND 4IN + 4IN − 3IN + 3IN − description/ordering information The LP239, LP339, LP2901 are low-power quadruple differential comparators. Each device consists of four independent voltage comparators designed specifically to operate from a single power supply and typically to draw 60-µA drain current over a wide range of voltages. Operation from split power supplies also is possible and the ultra-low power-supply drain current is independent of the power-supply voltage. Applications include limit comparators, simple analog-to-digital converters, pulse generators, squarewave generators, time-delay generators, voltage-controlled oscillators, multivibrators, and high-voltage logic gates. The LP239, LP339, LP2901 were designed specifically to interface with the CMOS logic family. The ultra-low power-supply current makes these products desirable in battery-powered applications. The LP239 is characterized for operation from −25°C to 85°C. The LP339 is characterized for operation from 0°C to 70°C. The LP2901 is characterized for operation from −40°C to 85°C. ORDERING INFORMATION TA VIOMAX AT 25°C PDIP (N) 0°C 0 C to 70 70°C C ± 5 mV SOIC (D) PDIP (N) −40°C −40 C to 85 85°C C ± 5 mV ORDERABLE PART NUMBER PACKAGE† SOIC (D) Tube of 25 LP339N Tube of 50 LP339D Reel of 2500 LP339DR Tube of 25 LP2901N Tube of 50 LP2901D Reel of 2500 LP2901DR TOP-SIDE MARKING LP339N LP339 LP2901N LP2901 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2004, Texas Instruments Incorporated     ! " #$%! "  &$'(#! )!%* )$#!" # ! "&%##!" &% !+% !%"  %," "!$%!" "!)) -!.* )$#! &#%""/ )%" ! %#%""(. #($)% !%"!/  (( &%!%"* POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 



    
    The LP239 is obsolete and is no longer supplied. SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004 schematic diagram (each comparator) VCC 0.2 µA 5 µA 6 µA 0.2 µA IN+ OUT IN− GND absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±36 V Input voltage range, VI (either input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 36 V Input current, VI ≤ −0.3 V (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Duration of output short-circuit to ground (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited Continuous total dissipation (see Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: LP239 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25°C to 85°C LP339 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C LP2901 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C Package thermal impedance, θJA (see Notes 6 and 7): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80°C/W Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Lead temperature range 1,6 mm (1/16 inch) from case for 60 seconds: J package . . . . . . . . . . . . . . . . 300°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the network ground. 2. Differential voltages are at IN+ with respect to IN −. 3. This input current only exists when the voltage at any of the inputs is driven negative. The current flows through the collector-base junction of the input clamping device. In addition to the clamping device action, there is lateral n-p-n parasitic transistor action. This action is not destructive, and normal output states are reestablished when the input voltage returns to a value more positive than − 0.3 V at TA = 25°C. 4. Short circuits between outputs to VCC can cause excessive heating and eventual destruction. 5. If the output transistors are allowed to saturate, the low-bias dissipation and the on-off characteristics of the outputs keep the dissipation very small (usually less than 100 mW). 6. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can impact reliability. 7. The package thermal impedance is calculated in accordance with JESD 51-7. DISSIPATION RATING TABLE PACKAGE J 2 TA ≤ 25°C POWER RATING 1025 mW DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING TA = 85°C POWER RATING 8.2 mW/°C 656 mW 533 mW POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 



    
    The LP239 is obsolete and is no longer supplied. SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004 recommended operating conditions LP239 VCC LP339 LP2901 MIN MAX MIN MAX MIN MAX 3 30 3 30 3 30 V 0 3 0 3 0 3 V Common-mode input voltage VCC = 5 V VCC = 30 V 0 28 0 28 0 28 V 0 3 0 3 0 3 V VI Input voltage VCC = 5 V VCC = 30 V 0 28 0 28 0 28 V TA Operating free-air temperature −25 85 0 70 −40 85 °C VIC Supply voltage UNIT electrical characteristics, VCC = 5 V, TA = 25°C (unless otherwise noted) PARAMETER VIO Input offset voltage IIO Input offset current IIB Input bias current TEST CONDITIONS VCC = 5 V to 30 V, RS = 0, VO = 2 V, See Note 6 TA† 25°C MIN ±0.5 ±5 ±1 ±15 −2.5 −25 −4 −40 Full range See Note 7 Common-mode input voltage range Single supply Large-signal differential voltage amplification VCC = 15 V, Output sink current VI− = 1 V, VI+ = 0 Output leakage current ±5 ±9 25°C AVD MAX ±2 Full range 25°C VICR TYP VI+ = 1 V, VI− = 0 Full range 25°C 0 to VCC − 1.5 Full range 0 to VCC − 2 VO = 0.4 V VO = 5 V VO = 30 V VI ≤ 0 (or VCC − on split supplies) 500 25°C 20 Full range 15 25°C 0.2 mV nA nA V RL = 15 kΩ VO = 2 V, See Note 8 UNIT V/mV 30 mA 0.7 25°C 0.1 Full range nA 1 µA VID Differential input voltage 36 V ICC Supply current RL = ∞ all comparators 60 100 µA † Full range is −25°C to 85°C for the LP239, 0°C to 70°C for the LP339, and − 40°C to 85°C for the LP2901. NOTES: 8. VIO is measured over the full common-mode input voltage range. 9. Because of the p-n-p input stage, the direction of the current is out of the device. This current essentially is constant (i.e., independent of the output state). No loading change exists on the reference or input lines as long as the common-mode input voltage range is not exceeded. 10. The output sink current is a function of the output voltage. These devices have a bimodal output section that allows them to sink (via a Darlington connection) large currents at output voltages greater than 1.5 V, and smaller currents at output voltages less than 1.5 V. switching characteristics, VCC = 5 V, TA = 25°C, RL connected to 5 V through 5.1 kΩ PARAMETER Large-signal response time Response time TEST CONDITIONS TTL logic swing, Vref = 1.4 V POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MIN TYP 1.3 8 MAX UNIT µs 3 



    
    SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004 The LP239 is obsolete and is no longer supplied. APPLICATION INFORMATION Figure 1 shows the basic configuration for using the LP239, LP339, or LP2901 comparator. Figure 2 shows the diagram for using one of these comparators as a CMOS driver. VCC VCC 30 kΩ IN + 100 kΩ + IN + + IN − − 3 OUT OUT IN − − 1/4 LP239, LP339, or LP2901 12 1/4 LP239, LP339, or LP2901 Figure 1. Basic Comparator 1/4 SN54/74LS00 or 1/4 SN54/74ALS1000A Figure 2. CMOS Driver All pins of any unused comparators should be grounded. The bias network of the LP239, LP339, and LP2901 establishes a drain current that is independent of the magnitude of the power-supply voltage over the range of 2 V to 30 V. It usually is necessary to use a bypass capacitor across the power supply line. The differential input voltage may be larger than VCC without damaging the device. Protection should be provided to prevent the input voltages from going negative by more than −0.3 V. The output section has two distinct modes of operation: a Darlington mode and ground-emitter mode. This unique drive circuit permits the device to sink 30 mA at VO = 2 V in the Darlington mode and 700 µA at VO = 0.4 V in the ground-emitter mode. Figure 3 is a simplified schematic diagram of the output section. The output section is configured in a Darlington connection (ignoring Q3). If the output voltage is held high enough (above 1 V), Q1 is not saturated and the output current is limited only by the product of the hFE of Q1, the hFE of Q2, and I1 and the 60-Ω saturation resistance of Q2. The devices are capable of driving LEDs, relays, etc. in this mode while maintaining an ultra-low power-supply current of 60 µA, typically. VCC I1 = 6 µA Q3 VO Q1 Q2 Figure 3. Output-Section Schematic Diagram 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 The LP239 is obsolete and is no longer supplied.



    
    SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Without transistor Q3, if the output voltage were allowed to drop below 0.8 V, transistor Q1 would saturate, and the output current would drop to zero. The circuit would be unable to pull low current loads down to ground or the negative supply, if used. Transistor Q3 has been included to bypass transistor Q1 under these conditions and apply the current I1 directly to the base of Q2. The output sink current now is approximately I1 times the hFE of Q2 (700 µA at VO = 0.4 V). The output of the devices exhibits a bimodal characteristic, with a smooth transition between modes. In both cases, the output is an uncommitted collector. Several outputs can be tied together to provide a dot logic function. An output pullup resistor can be connected to any available power-supply voltage within the permitted power-supply range, and there is no restriction on this voltage, based on the magnitude of the voltage that is supplied to VCC of the package. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 13-Jul-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) LP2901D ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LP2901 Samples LP2901DR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LP2901 Samples LP2901DRE4 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LP2901 Samples LP2901DRG4 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LP2901 Samples LP2901N ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 LP2901N Samples LP339D ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LP339 Samples LP339DG4 ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LP339 Samples LP339DR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM 0 to 70 LP339 Samples LP339DRE4 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LP339 Samples LP339DRG4 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 LP339 Samples LP339N ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 LP339N Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of