User's Guide
SNVA339A – April 2008 – Revised April 2013
AN-1830 LP38501ATJ-ADJ Evaluation Board
1
Introduction
The LP38501ATJ-ADJ is a 3A low-dropout (LDO) linear regulator in the thin TO-263 package that has an
adjustable output voltage (set by external resistors).
2
Basic Application Circuit
The basic application circuit that is built up on the evaluation board is shown in Figure 1:
Figure 1. Basic Application Circuit
3
Changing the Output Voltage
The resistors R1 and R2 set the output voltage. Equation 1 determines output voltage:
VOUT = VADJ x (1 + R1/R2)
(1)
where VADJ is typically 0.6 V.
The board has installed values of:
R1 = 19.1 kΩ
R2 = 6.04 kΩ
which sets the output to 2.5 V.
R1 can be adjusted to change the nominal output voltage to other values. The minimum output voltage
which can be set is the ADJ pin voltage, which is approximately 0.6 V. This is obtained by installing a
jumper or low value resistor (less than 10 Ω) at R1. The maximum usable output voltage is limited by the
maximum input voltage which is 5.5 V. Since rated dropout voltage at full current is 0.375 V, this means
the maximum usable output voltage for full current operation is about 5.1 V.
All trademarks are the property of their respective owners.
SNVA339A – April 2008 – Revised April 2013
Submit Documentation Feedback
AN-1830 LP38501ATJ-ADJ Evaluation Board
Copyright © 2008–2013, Texas Instruments Incorporated
1
Feedforward Capacitor C2
4
www.ti.com
Feedforward Capacitor C2
The PCB layout includes a location for C2, which is a feedforward capacitor connected across R1. If the
data sheet guidelines are followed, and R2 does not exceed 10 kΩ, C2 is not required and has no effect
on performance. The internal compensation is such that an internal zero provides more than adequate
phase margin so external compensation is never needed.
However, if the value of R2 is increased above 10 kΩ, the effect of the internal zero gradually diminishes
and the phase margin is reduced. At an R2 value of approximately 50 kΩ, the phase margin will be low
enough that instability may occur. In such cases, some of the lost phase margin can be regained by
placing a capacitor at C2. Although it is sometimes possible to regain adequate phase margin this way, it
is recommended that the data sheet guidelines be followed and R2 not exceed 10 kΩ (so C2 is never
required).
5
Power Dissipation
The power dissipated within the regulator IC is given by:
PD = IL (VIN - VOUT)
(2)
Where:
PD is the power dissipated in the IC regulator U1.
IL is the load current.
VIN is the value of VIN measured at TP2 (not at J1).
VOUT is the value of VOUT measured at TP5 (not at J4).
The thermal resistance of U1 from junction to ambient can be assumed to be approximately 30°C/W for
this assembly. That means that the junction temperature will rise about 30°C above ambient for each Watt
of power dissipated within the IC.
The parametric specifications of the IC are for a maximum junction temperature of 125°C, and the
maximum allowable junction temperature is 150°C. This limits maximum usable power dissipation for this
package to approximately 3.3W. If power dissipation exceeds this (and the junction temperature
approaches 150°C) the part may go into thermal shutdown.
2
AN-1830 LP38501ATJ-ADJ Evaluation Board
Copyright © 2008–2013, Texas Instruments Incorporated
SNVA339A – April 2008 – Revised April 2013
Submit Documentation Feedback
PCB Component Layout
www.ti.com
6
PCB Component Layout
The components listed in the basic application circuit can be identified using the silkscreen on the top
layer of the PCB (see Figure 2).
Figure 2. Top View of the PCB Assembly
SNVA339A – April 2008 – Revised April 2013
Submit Documentation Feedback
AN-1830 LP38501ATJ-ADJ Evaluation Board
Copyright © 2008–2013, Texas Instruments Incorporated
3
Bill of Materials (BOM)
7
www.ti.com
Bill of Materials (BOM)
The initial evaluation boards were built up for a 2.5 V regulated output. The components used in the PCB
assembly are listed in Table 1.
Table 1. Bill of Materials (BOM)
Designator
Qty.
Description
PCB
1
PC board
551600156-001
R1
1
Resistor, 19.1kΩ, 1%
Vishay CRCW08051912F
R2
1
Resistor, 6.04kΩ, 1%
Vishay CRCW08056041F
R3
1
Resistor, 51.1kΩ, 1%
Vishay CRCW08055112F
J1
1
Red Banana Jack
Digi-Key J-151-ND
J2,J3
2
Black Banana Jack
Digi-Key J-152-ND
J4
1
Blue Banana Jack
Digi-Key J-155-ND
C1,C3
2
Cap, CER, 10 µF
Digi-Key PCC2225CT-ND
TP1-TP5
5
Test Points
Newark 160-2043-02-01-00
U1
1
IC, LP38501
LP38501
C2
4
Part Number
****NOT INSTALLED FOR THIS ASSEMBLY
AN-1830 LP38501ATJ-ADJ Evaluation Board
Copyright © 2008–2013, Texas Instruments Incorporated
SNVA339A – April 2008 – Revised April 2013
Submit Documentation Feedback
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated