Product
Folder
Sample &
Buy
Technical
Documents
Support &
Community
Tools &
Software
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
LP387x 0.8-A Fast Ultra-Low-Dropout Linear Regulators
1 Features
3 Description
•
•
•
•
•
•
•
•
•
•
•
•
The LP3871 and LP3874 series of fast ultra-lowdropout linear regulators operate from a 2.5-V to 7-V
input supply. Wide range of preset output voltage
options are available. These ultra-low-dropout linear
regulators respond very quickly to step changes in
load, which makes them suitable for low voltage
microprocessor applications. The devices are
developed on a CMOS process which allows low
quiescent current operation independent of output
load current. This CMOS process also allows the
LP3871 and LP3874 to operate under extremely low
dropout conditions.
1
Input Voltage: 2.5 V to 7 V
Ultra-Low-Dropout Voltage
Low Ground Pin Current
Load Regulation of 0.04%
10-nA Quiescent Current in Shutdown Mode
Specified Output Current of 0.8-A DC
Output Voltage Accuracy ±1.5%
ERROR Flag Indicates Output Status
SENSE Option Improves Load Regulation
Minimum Output Capacitor Requirements
Overtemperature/Overcurrent Protection
−40°C to +125°C Junction Temperature Range
2 Applications
•
•
•
•
•
•
•
•
Microprocessor Power Supplies
GTL, GTL+, BTL, and SSTL Bus Terminators
Power Supplies for DSPs
SCSI Terminator
Post Regulators
High-Efficiency Linear Regulators
Battery Chargers
Other Battery-Powered Applications
Dropout Voltage: Ultra-low-dropout voltage; typically
24 mV at 80-mA load current and 240 mV at 0.8-A
load current.
Ground Pin Current: Typically 6 mA at 0.8-A load
current.
Shutdown Mode: Typically 10-nA quiescent current
when the SD pin is pulled low.
ERROR Flag: ERROR flag goes low when the output
voltage drops 10% below nominal value.
SENSE: SENSE pin improves regulation at remote
loads.
Precision Output Voltage: Multiple output voltage
options are available ranging from 1.8 V to 5 V with a
ensured accuracy of ±1.5% at room temperature, and
±3% over all conditions (varying line, load, and
temperature).
Device Information(1)
PART NUMBER
LP3871
LP3874
PACKAGE
BODY SIZE (NOM)
SOT-223 (5)
6.50 mm x 3.56 mm
DDPAK/ TO-263 (5)
10.16 mm x 8.42 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Applications
*SD and ERROR pins must be pulled high
through a 10-kΩ pullup resistor. Connect
the ERROR pin to ground if this function is
not used. See Application and
Implementation for more information.
*SD must be pulled high through a 10-kΩ
pullup resistor. See Application and
Implementation for more information.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 8
7.1 Overview ................................................................... 8
7.2 Functional Block Diagrams ....................................... 8
7.3 Feature Description................................................... 8
7.4 Device Functional Modes.......................................... 9
8
Application and Implementation ........................ 11
8.1 Application Information............................................ 11
8.2 Typical Applications ............................................... 11
9
Power Supply Recommendations...................... 16
9.1 Power Dissipation .................................................. 16
10 Layout................................................................... 16
10.1 Layout Guidelines ................................................. 16
10.2 Layout Examples................................................... 16
11 Device and Documentation Support ................. 17
11.1
11.2
11.3
11.4
11.5
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
17
17
17
17
17
12 Mechanical, Packaging, and Orderable
Information ........................................................... 17
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision G (April 2013) to Revision H
Page
•
Added Pin Configuration and Functions section, ESD Rating table, Feature Description , Device Functional Modes,
Application and Implementation, Power Supply Recommendations, Layout, Device and Documentation Support ,
and Mechanical, Packaging, and Orderable Information sections; conform pin names in graphics to TI nomenclature....... 1
•
Deleted Lead temperature row - information in POA ............................................................................................................ 4
•
Deleted Heatsinking subsections regarding specific packages as specs have been updated (see Thermal
Information). ......................................................................................................................................................................... 16
•
Changed layout examples to eliminate obsolete thermal-value references ........................................................................ 16
Changes from Revision F (April 2013) to Revision G
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 16
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
LP3871, LP3874
www.ti.com
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
5 Pin Configuration and Functions
KTT Package
5-Pin DDPAK/TO-263
Top View
NC Package
5-Pin SOT-223
Top View
GND
5
1
2
3
SD
IN
OUT
4
ERROR
/SENSE
Pin Functions
PIN
NAME
LP3871
LP3874
TYPE
DESCRIPTION
SOT-223
DDPAK/TO-263
SOT-223
DDPAK/TO-263
ERROR
4
5
—
—
O
GND
5
3
5
3
GND
IN
2
2
2
2
I
Input voltage
OUT
3
4
3
4
O
Output voltage
SD
1
1
1
1
I
Shutdown
SENSE
—
—
4
5
I
Remote voltage sense
ERROR Flag
Ground
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
3
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
MAX
UNIT
Input supply voltage (survival)
−0.3
7.5
V
Shutdown input voltage (survival)
−0.3
7.5
V
Output voltage (survival) (3) (4)
−0.3
6
V
IOUT (survival)
Short-circuit protected
Maximum voltage for ERROR Pin
VIN
V
Maximum voltage for SENSE Pin
VOUT
V
Power dissipation (5)
Internally Limited
−65
Storage temperature, Tstg
(1)
(2)
(3)
(4)
(5)
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
If used in a dual-supply system where the regulator load is returned to a negative supply, the output must be diode-clamped to ground.
The output PMOS structure contains a diode between the IN and OUT pins. This diode is normally reverse biased. This diode will get
forward biased if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can typically
withstand 200 mA of DC current and 1 A of peak current.
Internal thermal shutdown circuitry protects the device from permanent damage.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Input supply voltage
(1)
Shutdown input voltage
MIN
MAX
2.5
7
V
−0.3
7
V
0.8
A
125
°C
Maximum operating current (DC)
−40
Junction temperature
(1)
UNIT
The minimum operating value for VIN is equal to either [VOUT(NOM) + VDROPOUT] or 2.5 V, whichever is greater.
6.4 Thermal Information
LP3871, LP3874
THERMAL METRIC (1)
NC (SOT-223)
KTT (DDPAK/TO-263)
5 PINS
5 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
65.2
40.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
47.2
43.4
°C/W
RθJB
Junction-to-board thermal resistance
9.9
23.1
°C/W
ψJT
Junction-to-top characterization parameter
3.4
11.5
°C/W
ψJB
Junction-to-board characterization parameter
9.7
22
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
—
1
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
LP3871, LP3874
www.ti.com
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
6.5 Electrical Characteristics
Unless otherwise specified: TJ = 25°C, VIN = VO(NOM) + 1 V, IL = 10 mA, COUT = 10 µF, VSD = 2 V.
MIN (1)
TYP (2)
MAX (1)
VOUT + 1 V ≤ VIN ≤ 7 V, 10 mA ≤ IL ≤ 0.8 A
–1.5%
0%
1.5%
VOUT + 1 V ≤ VIN ≤ 7 V, 10 mA ≤ IL ≤ 0.8 A,
–40°C ≤ TJ ≤ 125°C
–3%
PARAMETER
Output voltage tolerance
TEST CONDITIONS
(3)
VOUT
ΔVOL
ΔVO/
ΔIOUT
Output voltage line regulation (3)
Output voltage load regulation (3)
0.02%
VOUT + 1 V ≤ VIN ≤ 7 V, –40°C ≤ TJ ≤ 125°C
0.06%
10 mA ≤ IL ≤ 0.8 A
0.04%
0.1%
IL = 80 mA
VIN –
VOUT
Dropout voltage (4)
3%
VOUT + 1 V ≤ VIN ≤ 7 V
10 mA ≤ IL ≤ 0.8 A, –40°C ≤ TJ ≤ 125°C
24
35
240
300
IL = 80 mA, –40°C ≤ TJ ≤ 125°C
40
IL = 0.8 A
IL = 0.8 A, –40°C ≤ TJ ≤ 125°C
5
IL = 150 mA, –40°C ≤ TJ ≤ 125°C
Ground pin current in normal
operation mode
IGND
Ground pin current in shutdown
mode
VSD ≤ 0.3 V
IO(PK)
Peak output current
VOUT ≥ VO(NOM) – 4%
mV
350
IL = 150 mA
IGND
UNIT
9
10
IL = 0.8 A
6
IL = 0.8 A, –40°C ≤ TJ ≤ 125°C
14
mA
15
0.01
–40°C ≤ TJ ≤ 85°C
10
µA
50
1
A
2.3
A
SHORT CIRCUIT PROTECTION
ISC
Short-circuit current
SHUTDOWN INPUT
Output = High
Output = High, –40°C ≤ TJ ≤ 125°C
VIN
2
VSDT
Shutdown threshold
TdOFF
Turnoff delay
IL = 0.8 A
20
µs
TdON
Turnon delay
IL = 0.8 A
25
µs
ISD
SD input current
VSD = VIN
1
nA
Output = Low
V
0
Output = Low, –40°C ≤ TJ ≤ 125°C
0.3
ERROR FLAG
Threshold
VT
See (5)
See (5), –40°C ≤ TJ ≤ 125°C
Threshold hysteresis
VTH
See
10%
5%
(5)
See (5), –40°C ≤ TJ ≤ 125°C
Isink = 100 µA
16%
5%
2%
8%
0.02
VEF(Sat)
ERROR flag saturation
Td
Flag reset delay
1
µs
Ilk
ERROR flag pin leakage current
1
nA
Imax
ERROR flag pin sink current
1
mA
(1)
(2)
(3)
(4)
(5)
Isink = 100 µA, –40°C ≤ TJ ≤ 125°C
VError = 0.5 V
0.1
V
Limits are specified by testing, design, or statistical correlation.
Typical numbers are at 25°C and represent the most likely parametric norm.
Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage.
Output voltage load regulation is defined as the change in output voltage from the nominal value due to change in load current. The line
and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the
output voltage tolerance specification.
Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value.
Dropout voltage specification applies only to output voltages of 2.5 V and above. For output voltages below 2.5 V, the dropout voltage is
nothing but the input to output differential, because the minimum input voltage is 2.5 V.
ERROR Flag threshold and hysteresis are specified as percentage of regulated output voltage. See ERROR Flag Operation.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
5
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
www.ti.com
Electrical Characteristics (continued)
Unless otherwise specified: TJ = 25°C, VIN = VO(NOM) + 1 V, IL = 10 mA, COUT = 10 µF, VSD = 2 V.
PARAMETER
TEST CONDITIONS
MIN (1)
TYP (2)
MAX (1)
UNIT
AC PARAMETERS
PSRR
ρn(l/f)
en
6
Ripple rejection
Output noise density
Output noise voltage
VIN = VOUT + 1 V, COUT = 10 µF
VOUT = 3.3 V, ƒ = 120 Hz
73
VIN = VOUT + 0.5 V, COUT = 10 µF
VOUT = 3.3 V, ƒ = 120 Hz
57
dB
ƒ = 120 Hz
0.8
BW = 10 Hz – 100 kHz, VOUT = 2.5 V
150
BW = 300 Hz – 300 kH, VOUT = 2.5 V
100
Submit Documentation Feedback
µV
µVRMS
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
LP3871, LP3874
www.ti.com
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
6.6 Typical Characteristics
Unless otherwise specified: TJ = 25°C, COUT = 10 µF, CIN = 10 µF, SD pin is tied to VIN, VOUT = 2.5 V, VIN = VO(NOM) + 1 V,
IL = 10 mA.
6
500
125oC
300
25oC
200
-40oC
5
GROUND PIN CURRENT (mA)_
DROPOUT VOLTAGE (mV)
400
4
3
2
1
100
0
1.8
0
0
0.5
2.3
2.8
3.3
3.8
4.3
5.0
1.0
OUTPUT VOLTAGE (V)
LOAD CURRENT (A)
IL = 800 mA
Figure 1. Dropout Voltage vs Output Load Current
Figure 2. Ground Current vs Output Voltage
10
ERROR THRESHOLD (% of VOUT)
14
SHUTDOWN IQ (PA)
1
0.1
0.01
0.001
-40 -20
12
10
8
6
4
2
0
0
20
40
60
80
-40 -20
100 125
Figure 3. Shutdown IQ vs Junction Temperature
40
60
80 100 125
3
' VOUT/VOLT CHANGE in VIN (mV)
DC LOAD REGULATION (mV/A)
20
Figure 4. ERROR Flag Threshold vs Junction Temperature
3
2.5
2
1.5
1
0.5
0
-40
0
JUNCTION TEMPERATURE (oC)
TEMPERATURE (oC)
-20
0
20
40
60
80
2.5
2
1.5
1
0.5
0
-40
100 125
o
-20
0
20
40
60
80
100 125
o
JUNCTION TEMPERATURE ( C)
JUNCTION TEMPERATURE ( C)
Figure 5. DC Load Regulation vs Junction Temperature
Figure 6. DC Line Regulation vs Temperature
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
7
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LP3871 and LP3874 linear regulators are designed to provide an ultra-low-dropout voltage with excellent
transient response and load/line regulation. For battery-powered always-on type applications, the very low
quiescent current of LP3871 and LP3874 in shutdown mode helps reduce battery drain. For applications where
load is not placed close to the regulator, LP3874 incorporates a voltage sense circuit to improve voltage
regulation at the point of load. The ERROR output pin of LP3871 can be used in the system to flag a low-voltage
condition.
7.2 Functional Block Diagrams
Figure 7. LP3871 Block Diagram
Figure 8. LP3874 Block Diagram
7.3 Feature Description
7.3.1 Shutdown (SD)
The LM3871 and LP3874 devices have a shutdown feature that turns the device off and reduces the quiescent
current to 10 nA, typical.
8
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
LP3871, LP3874
www.ti.com
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
Feature Description (continued)
7.3.2 Short-Circuit Protection
The LP3871and LP3874 devices are short-circuit protected and, in the event of a peak overcurrent condition, the
short-circuit control loop will rapidly drive the output PMOS pass element off. Once the power pass element shuts
down, the control loop will rapidly cycle the output on and off until the average power dissipation causes the
thermal shutdown circuit to respond to servo the on/off cycling to a lower frequency.
7.3.3 Low Dropout Voltage
The LP3871 and LP3874 devices feature an ultra-low-dropout voltage, typically 24 mV at 80-mA load current and
240 mV at 0.8-A load current.
The dropout voltage of a regulator is defined as the minimum input-to-output differential required to stay within
2% of the nominal output voltage. For CMOS LDOs, the dropout voltage is the product of the load current and
the Rds(on) of the internal MOSFET.
7.3.4 SENSE Pin
In applications where the regulator output is not very close to the load, LP3874 can provide better remote load
regulation using the SENSE pin. Figure 9 depicts the advantage of the SENSE option. LP3871 regulates the
voltage at the OUT pin. Hence, the voltage at the remote load will be the regulator output voltage minus the drop
across the trace resistance. For example, in the case of a 3.3-V output, if the trace resistance is 100 mΩ, the
voltage at the remote load will be 3.22 V with 0.8 A of load current, ILOAD. The LP3874 regulates the voltage at
the SENSE pin. Connecting the SENSE pin to the remote load will provide regulation at the remote load, as
shown in Figure 9. If the SENSE option pin is not required, the SENSE pin must be connected to the OUT pin.
Figure 9. Improving Remote Load Regulation using LP3874
7.4 Device Functional Modes
7.4.1 Shutdown Mode
A CMOS logic low level signal at the shutdown (SD) pin will turn off the regulator. The SD pin must be actively
terminated through a 10-kΩ pullup resistor for a proper operation. If this pin is driven from a source that actively
pulls high and low (such as a CMOS rail-to-rail comparator), the pullup resistor is not required. This pin must be
tied to VIN if not used.
7.4.2 Active Mode
When voltage at SD pin of the LP3871 and LP3874 devices is at logic high level, the device is in normal mode of
operation.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
9
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
www.ti.com
Device Functional Modes (continued)
7.4.3 ERROR Flag Operation
The LP3871 produces logic low signals at the ERROR Flag pin when the output drops out of regulation due to
low input voltage, current limiting, or thermal limiting. This flag has a built-in hysteresis. The timing diagram in
Figure 10 shows the relationship between the ERROR flag and the output voltage. In this example, the input
voltage is changed to demonstrate the functionality of the ERROR Flag.
The internal ERROR flag comparator has an open drain output stage. Hence, the ERROR pin must be pulled
high through a pullup resistor. Although the ERROR flag pin can sink current of 1mA, this current is energy drain
from the input supply. Hence, the value of the pullup resistor must be in the range of 10 kΩ to 1 MΩ. The
ERROR pin must be connected to ground if this function is not used. It must also be noted that when the
shutdown pin is pulled low, the ERROR pin is forced to be invalid for reasons of saving power in shutdown
mode.
Figure 10. ERROR Flag Operation
10
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
LP3871, LP3874
www.ti.com
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers must
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP3871 and LP3874 devices are linear regulators designed to provide high load current of up to 0.8 A, low
dropout voltage, and low quiescent current in shutdown mode.
8.1.1 Reverse Current Path
The internal MOSFET in LP3871 and LP3874 has an inherent parasitic diode. During normal operation, the input
voltage is higher than the output voltage and the parasitic diode is reverse biased. However, if the output is
pulled above the input in an application, then current flows from the output to the input as the parasitic diode gets
forward biased. The output can be pulled above the input as long as the current in the parasitic diode is limited to
200-mA continuous and 1-A peak.
8.1.2 Turnon Characteristics for Output Voltages Programmed To 2 V or Below
As VIN increases during start-up, the regulator output will track the input until VIN reaches the minimum operating
voltage (typically about 2.5 V). For output voltages programmed to 2 V or below, the regulator output may
momentarily exceed its programmed output voltage during start-up. Outputs programmed to voltages above 2 V
are not affected by this behavior.
8.2 Typical Applications
*SD and ERROR pins must be pulled high through a 10-kΩ pullup resistor. Connect the ERROR pin to ground if this
function is not used.
Figure 11. LP3871 Typical Application
*SD must be pulled high through a 10-kΩ pullup resistor.
Figure 12. LP3874 Typical Application
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
11
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
www.ti.com
Typical Applications (continued)
8.2.1 Design Requirements
For LP3871 and LP3874 typical applications, use the parameters listed in Table 1.
Table 1. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage
2.5 V to 7 V
Output voltage
2.5 V
Output current
0.8 A
Output capacitor
10 µF
Input capacitor
10 µF
Output capacitor ESR range
100 mΩ to 4 Ω
8.2.2 Detailed Design Procedure
8.2.2.1 External Capacitors
Like any low-dropout regulator, external capacitors are required to assure stability. These capacitors must be
correctly selected for proper performance.
• Input Capacitor: An input capacitor of at least 10 μF is required. Ceramic, tantalum, or Electrolytic capacitors
may be used, and capacitance may be increased without limit.
• Output Capacitor: An output capacitor is required for loop stability. It must be located less than 1 cm from the
device and connected directly to the output and ground pins using traces which have no other currents
flowing through them (see Layout Guidelines).
The minimum value of output capacitance that can be used for stable full-load operation is 10 µF, but it may be
increased without limit. The output capacitor must have an equivalent series resistance (ESR) value as shown in
the stable region of the curve (Figure 13). Tantalum capacitors are recommended for the output capacitor.
10
COUT ESR (:)
1.0
COUT > 10PF
STABLE REGION
0.1
.01
.001
0
0.2
0.4
0.6
0.8
1
LOAD CURRENT (A)
Figure 13. ESR Curve
8.2.2.2 Selecting a Capacitor
It is important to note that capacitance tolerance and variation with temperature must be taken into consideration
when selecting a capacitor so that the minimum required amount of capacitance is provided over the full
operating temperature range. In general, a good Tantalum capacitor will show very little capacitance variation
with temperature, but a ceramic may not be as good (depending on dielectric type). Aluminum electrolytics also
typically have large temperature variation of capacitance value.
Equally important to consider is a capacitor's ESR change with temperature: this is not an issue with ceramics,
as their ESR is extremely low. However, it is very important in Tantalum and aluminum electrolytic capacitors.
Both show increasing ESR at colder temperatures, but the increase in aluminum electrolytic capacitors is so
severe they may not be feasible for some applications (see Capacitor Characteristics).
12
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
LP3871, LP3874
www.ti.com
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
8.2.2.3 Capacitor Characteristics
8.2.2.3.1 Ceramic
For values of capacitance in the 10-µF to 100-µF range, ceramics are usually larger and more costly than
tantalum capacitors but give superior AC performance for bypassing high frequency noise because of very low
ESR (typically less than 10 mΩ). However, some dielectric types do not have good capacitance characteristics
as a function of voltage and temperature.
Z5U and Y5V dielectric ceramics have capacitance that drops severely with applied voltage. A typical Z5U or
Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. The Z5U and Y5V
also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of
the temperature range.
X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically
maintain a capacitance range within ±20% of nominal over full operating ratings of temperature and voltage. Of
course, they are typically larger and more costly than Z5U/Y5U types for a given voltage and capacitance.
8.2.2.3.2 Tantalum
Solid tantalum capacitors are recommended for use on the output because their typical ESR is very close to the
ideal value required for loop compensation. They also work well as input capacitors if selected to meet the ESR
requirements previously listed.
Tantalums also have good temperature stability: a good quality tantalum will typically show a capacitance value
that varies less than 10-15% across the full temperature range of 125°C to −40°C. ESR will vary only about 2X
going from the high to low temperature limits.
The increasing ESR at lower temperatures can cause oscillations when marginal quality capacitors are used (if
the ESR of the capacitor is near the upper limit of the stability range at room temperature).
8.2.2.3.3 Aluminum
This capacitor type offers the most capacitance for the money. The disadvantages are that they are larger in
physical size, not widely available in surface mount, and have poor AC performance (especially at higher
frequencies) due to higher ESR and ESL.
Compared by size, the ESR of an aluminum electrolytic is higher than either tantalum or ceramic, and it also
varies greatly with temperature. A typical aluminum electrolytic can exhibit an ESR increase of as much as 50×
when going from 25°C down to −40°C.
It must also be noted that many aluminum electrolytics only specify impedance at a frequency of 120 Hz, which
indicates they have poor high frequency performance. Only aluminum electrolytics that have an impedance
specified at a higher frequency (between 20 kHz and 100 kHz) must be used for the LP387X. Derating must be
applied to the manufacturer's ESR specification, since it is typically only valid at room temperature.
Any applications using aluminum electrolytics must be thoroughly tested at the lowest ambient operating
temperature where ESR is maximum.
8.2.2.4 RFI/EMI Susceptibility
Radio frequency interference (RFI) and electromagnetic interference (EMI) can degrade the performance of any
integrated circuit because of the small dimensions of the geometries inside the device. In applications where
circuit sources are present which generate signals with significant high frequency energy content (> 1 MHz), care
must be taken to ensure that this does not affect the device regulator.
If RFI/EMI noise is present on the input side of the regulator (such as applications where the input source comes
from the output of a switching regulator), good ceramic bypass capacitors must be used at the input pin of the
device.
If a load is connected to the device output which switches at high speed (such as a clock), the high-frequency
current pulses required by the load must be supplied by the capacitors on the device output. Since the bandwidth
of the regulator loop is less than 100 kHz, the control circuitry cannot respond to load changes above that
frequency. This means the effective output impedance of the device at frequencies above 100 kHz is determined
only by the output capacitor(s).
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
13
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
www.ti.com
In applications where the load is switching at high speed, the output of the device may need RF isolation from
the load. It is recommended that some inductance be placed between the output capacitor and the load, and
good RF bypass capacitors be placed directly across the load.
PCB layout is also critical in high noise environments, since RFI/EMI is easily radiated directly into PC traces.
Noisy circuitry must be isolated from "clean" circuits where possible, and grounded through a separate path. At
MHz frequencies, ground planes begin to look inductive and RFI/EMI can cause ground bounce across the
ground plane.
In multi-layer PCB applications, care must be taken in layout so that noisy power and ground planes do not
radiate directly into adjacent layers which carry analog power and ground.
8.2.2.5 Output Noise
Noise is specified in two ways:
• Spot Noise (or Output Noise Density): the RMS sum of all noise sources, measured at the regulator output, at
a specific frequency (measured with a 1-Hz bandwidth). This type of noise is usually plotted on a curve as a
function of frequency.
• Total Output Noise (or Broad-Band Noise): the RMS sum of spot noise over a specified bandwidth, usually
several decades of frequencies.
Attention must be paid to the units of measurement. Spot noise is measured in units µV/√Hz or nV/√Hz and total
output noise is measured in µVRMS.
The primary source of noise in low-dropout regulators is the internal reference. In CMOS regulators, noise has a
low frequency component and a high frequency component, which depend strongly on the silicon area and
quiescent current. Noise can be reduced in two ways: by increasing the transistor area or by increasing the
current drawn by the internal reference. Increasing the area will decrease the chance of fitting the die into a
smaller package. Increasing the current drawn by the internal reference increases the total supply current
(ground pin current). Using an optimized trade-off of ground pin current and die size, the LP3871 and LP3874
achieve low noise performance and low quiescent-current operation.
The total output noise specification for LP3871 and LP3874 devices is presented in Electrical Characteristics.
The output noise density at different frequencies is represented by a curve under Typical Characteristics.
14
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
LP3871, LP3874
www.ti.com
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
8.2.3 Application Curves
Unless otherwise specified: TJ = 25°C, COUT = 10 µF, CIN = 10 µF, SD pin is tied to VIN, VOUT = 2.5 V, VIN = VO(NOM) + 1 V,
IL = 10 mA.
VOUT
100mV/DIV
MAGNITUDE
MAGNITUDE
VOUT
100mV/DIV
ILOAD
1A/DIV
ILOAD
1A/DIV
TIME (50Ps/DIV)
TIME (50Ps/DIV)
CIN = COUT = 10 µF, Oscon
CIN = COUT = 100 µF, Oscon
Figure 14. Load Transient Response
Figure 15. Load Transient Response
VOUT
100mV/DIV
MAGNITUDE
MAGNITUDE
VOUT
100mV/DIV
ILOAD
1A/DIV
ILOAD
1A/DIV
TIME (50Ps/DIV)
TIME (50Ps/DIV)
CIN = COUT = 10 µF, Poscap
CIN = COUT = 10 µF, Tantalum
Figure 16. Load Transient Response
Figure 17. Load Transient Response
MAGNITUDE
VOUT
100mV/DIV
ILOAD
1A/DIV
TIME (50Ps/DIV)
CIN = COUT = 100 µF, Tantalum
Figure 18. Load Transient Response
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
15
LP3871, LP3874
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
www.ti.com
9 Power Supply Recommendations
9.1 Power Dissipation
LP3871 and LP3874 can deliver a continuous current of 0.8 A over the full operating temperature range. A
heatsink may be required depending on the maximum power dissipation and maximum ambient temperature of
the application. Under all possible conditions, the junction temperature must be within the range specified under
operating conditions. The total power dissipation of the device is given by:
2& = :8+0 F 8176 ;+176 + :8+0 ;+)0&
where
•
IGND is the operating ground current of the device (specified under Electrical Characteristics).
(1)
The maximum allowable temperature rise (TRmax) depends on the maximum ambient temperature (TAmax) of the
application, and the maximum allowable junction temperature (TJmax):
64I=T = 6,I=T F 6#I=T
(2)
The maximum allowable value for junction to ambient thermal resistance, RθJA, can be calculated using the
formula:
4à,# = 64I=T F6#I=T /2&
(3)
10 Layout
10.1 Layout Guidelines
Good PC layout practices must be used or instability can be induced because of ground loops and voltage drops.
The input and output capacitors must be directly connected to the input, output, and ground pins of the regulator
using traces which do not have other currents flowing in them (Kelvin connect).
The best way to do this is to lay out CIN and COUT near the device with short traces to the IN, OUT, and ground
pins. The regulator ground pin must be connected to the external circuit ground so that the regulator and its
capacitors have a "single point ground".
It must be noted that stability problems have been seen in applications where "vias" to an internal ground plane
were used at the ground points of the device and the input and output capacitors. This was caused by varying
ground potentials at these nodes resulting from current flowing through the ground plane. Using a single point
ground technique for the regulator and its capacitors fixed the problem.
Since high current flows through the traces going into IN and coming from OUT, Kelvin connect the capacitor
leads to these pins so there is no voltage drop in series with the input and output capacitors.
10.2 Layout Examples
CIN
VIN
SD
SD
IN
VIN
IN
VOUT
OUT
CIN
GND
GND
COUT
OUT
ERROR/SENSE
COUT
VOUT
Figure 19. Layout Example for SOT-223 Package
16
ERROR/SENSE
Figure 20. Layout Example for TO-263 Package
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
LP3871, LP3874
www.ti.com
SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015
11 Device and Documentation Support
11.1 Related Links
Table 2 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 2. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LP3871
Click here
Click here
Click here
Click here
Click here
LP3874
Click here
Click here
Click here
Click here
Click here
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LP3871 LP3874
17
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LP3871EMP-1.8/NOPB
ACTIVE
SOT-223
NDC
5
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LH6B
LP3871EMP-2.5/NOPB
ACTIVE
SOT-223
NDC
5
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LH7B
LP3871EMP-3.3/NOPB
ACTIVE
SOT-223
NDC
5
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LH8B
LP3871EMP-5.0/NOPB
ACTIVE
SOT-223
NDC
5
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LH9B
LP3871EMPX-3.3/NOPB
ACTIVE
SOT-223
NDC
5
2000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LH8B
LP3871ES-1.8/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LP3871ES
-1.8
LP3871ES-2.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LP3871ES
-2.5
LP3871ES-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LP3871ES
-3.3
LP3871ESX-1.8/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LP3871ES
-1.8
LP3871ESX-2.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LP3871ES
-2.5
LP3871ESX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LP3871ES
-3.3
LP3874EMP-1.8/NOPB
ACTIVE
SOT-223
NDC
5
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LHEB
LP3874EMP-2.5/NOPB
ACTIVE
SOT-223
NDC
5
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LHFB
LP3874EMP-3.3
NRND
SOT-223
NDC
5
1000
Non-RoHS
& Green
Call TI
Level-1-260C-UNLIM
-40 to 125
LHHB
LP3874EMP-3.3/NOPB
ACTIVE
SOT-223
NDC
5
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LHHB
LP3874EMP-5.0/NOPB
ACTIVE
SOT-223
NDC
5
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LHJB
LP3874EMPX-1.8/NOPB
ACTIVE
SOT-223
NDC
5
2000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LHEB
LP3874EMPX-3.3/NOPB
ACTIVE
SOT-223
NDC
5
2000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LHHB
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
30-Sep-2021
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LP3874EMPX-5.0/NOPB
ACTIVE
SOT-223
NDC
5
2000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
LHJB
LP3874ES-2.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LP3874ES
-2.5
LP3874ES-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
RoHS-Exempt
& Green
SN
Level-3-245C-168 HR
-40 to 125
LP3874ES
-3.3
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of