LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
LP3921 Battery Charger Management and Regulator Unit with Integrated Boomer™ Audio
Amplifier
Check for Samples: LP3921
FEATURES
DESCRIPTION
•
The LP3921 is a fully integrated charger and multiregulator unit with a fully differential Boomer audio
power amplifier designed for CDMA cellular phones.
The LP3921 has a high-speed serial interface which
allows for the integration and control of a Li-Ion
battery charger, 7 low-noise low-dropout (LDO)
voltage regulators and a Boomer audio amplifier.
1
23
•
•
•
•
•
•
Charger
– DC Adapter or USB Input
– Thermally Regulated Charge Current
– Under Voltage Lockout
– 50 to 950 mA Programmable Charge
Current
3.0V to 5.5V Input Voltage Range
Thermal Shutdown
I2C-Compatible Interface for Controlling
Charger, LDO Outputs and Enabling Audio
Output
LDO's 7 Low-Noise LDO’s
– 2 x 300 mA
– 3 x 150 mA
– 2 x 80 mA
2% (typ.) Output Voltage Accuracy on LDO's
Audio
– Fully Differential Amplification
– Ability to Drive Capacitive Loads up to 100
pF
– No Output Coupling Capacitors, Snubber
Networks or Bootstrap Capacitors Required
Space-Efficient 32-pin 5 x 5 mm WQFN
Package
APPLICATIONS
•
•
•
•
The Li-Ion charger integrates a power FET, reverse
current blocking diode, sense resistor with current
monitor output, and requires only a few external
components. Charging is thermally regulated to
obtain the most efficient charging rate for a given
ambient temperature.
LDO regulators provide high PSRR and low noise
ideally suited for supplying power to both analog and
digital loads.
The Boomer Audio Amplifier is capable of delivering
1.1 watts of continuous average power to an 8Ω BTL
load with less than 1% distortion (THD+N). Boomer
Audio Power Amplifiers were designed specifically to
provide high quality output power with a minimal
amount of external components. The Boomer Audio
Amplifier does not require output coupling capacitors
or bootstrap capacitors, and therefore is ideally suited
for mobile phone and other low voltage applications
where minimal power consumption and part count is
the primary requirement. The Boomer Audio Amplifier
contains advanced pop & click circuitry which
eliminates noises during turn-on and turn-off
transitions.
CDMA Phone Handsets
Low Power Wireless Handsets
Handheld Information Appliances
Personal Media Players
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Boomer is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
System Diagram
AC Adapter
Li-Ion Charger
Ichg
Monitor
I/O
Interface
of
Baseband
Processor
+
-
BB Processor
Power Domains
Serial
Interface
Memory
7 x LDO
2
Control
RF
Audio
Peripheral
Devices
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
Functional Block Diagram
VBATT
10 PF
BATT
CHG_IN
Battery
10 PF
VIN1
+
10 PF
VIN2
AC Adapter or
VBUS supply
4.5V to 6V
LDO1
IMON
LDO1
LDO2
Linear Charger
1 PF
CORE
1.8V
@300 mA
ACOK_N
LDO2
LDO2
1 PF
DIGI
3.0V
@300 mA
LDO2
320 ms
debounce
1.5k
LDO3
1.5k
LDO3
1 PF
SDA
ANA
3.0V
@80 mA
LDO2
O/D output
SCL
TCXO_EN
PON_N
LDO4
LDO4
PS_HOLD
1 PF
RESET_N
HF_PWR
320 ms
debounce
PWR_ON
30 ms
debounce
RX_EN
LDO5
LDO5
1 PF
500k
500k
VBATT
Serial
Interface
and Control
LP3921
LDO6
Thermal
Shutdown
1 PF
TX
3.0V
@150 mA
UVLO
LDO7
Voltage
Reference
1.0 PF
RX
3.0V
@150 mA
TX_EN
LDO6
VDD
TCXO
3.0V
@80 mA
LDO7
1 PF
GP
3.0V
@150 mA
VO+
Shut Down
20k
20k
VO+
-IN
- Differential Input
BOOMER AUDIO
+ Differential Input
RL 8:
+IN
20k
VO-
20k
VSS
GNDA
GND
BYP
VO-
1.0 PF
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
3
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
Connection Diagram
Figure 1. Device Pin Diagram
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
32
9
31
10
30
11
29
12
28
13
27
14
26
15
25
16
24
Device Description
The LP3921 Charge Management and Regulator Unit is designed to supply charger and voltage output
capabilities for mobile systems, e.g. CDMA handsets. The device provides a Li-Ion charging function and 7
regulated outputs. Communication with the device is via an I2C compatible serial interface that allows function
control and status read-back.
Battery Charge Management provides a programmable CC/CV linear charge capability. Following a normal
charge cycle a maintenance mode keeps battery voltage between programmable levels. Power levels are
thermally regulated to obtain optimum charge levels over the ambient temperature range.
CHARGER FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
Pre-charge, CC, CV and Maintenance modes
USB Charge 100 mA/450 mA
Integrated FET
Integrated Reverse Current Blocking Diode
Integrated Sense Resistor
Thermal regulation
Charge Current Monitor Output
Programmable charge current 50 mA - 950 mA with 50 mA steps
Default CC mode current 100 mA
Pre-charge current fixed 50 mA
Termination voltage 4.1V, 4.2V (default), 4.3V, and 4.4V, accuracy better than +/- 0.35% (typ.)
Restart level 100 mV, 150 mV (default) and 200 mV below Termination voltage
Programmable End of Charge 0.1C (default), 0.15C, 0.2C and 0.25C
Enable Control Input
Safety timer
Input voltage operating range 4.5V - 6.0V
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
REGULATORS
Seven low-dropout linear regulators provide programmable voltage outputs with current capabilities of 80 mA,
150 mA and 300 mA as given in the table below. LDO1, LDO2 and LDO3 are powered up by default with LDO1
reaching regulation before LDO2 and LDO3 are started. LDO1, LDO3 and LDO7 can be disabled/enabled via the
serial interface. LDO1 and LDO2, if enabled, must be in regulation for the device to power up and remain
powered. LDO4, LDO5 and LDO6 have external enable pins and may power up following LDO2 as determined
by their respective enable. Under voltage lockout oversees device start up with preset level of 2.85V (typ.).
POWER SUPPLY CONFIGURATIONS
At PMU start up, LDO1, LDO2 and LDO3 are always started with their default voltages. The start up sequence of
the LDO's is given below.
Startup Sequence
LDO1 -> LDO2 -> LDO3
LDO's with external enable control (LDO4, LDO5, LDO6) start immediately after LDO2 if enabled by logic high at
their respective control inputs.
LDO7 (and LDO1, LDO3) may be programmed to enable/disable once PS_HOLD has been asserted.
DEVICE PROGRAMMABILITY
An I2C compatible Serial Interface is used to communicate with the device to program a series of registers and
also to read status registers. These internal registers allow control over LDO outputs and their levels. The
charger functions may also be programmed to alter termination voltage, end of charge current, charger restart
voltage, full rate charge current, and also the charging mode.
This device internal logic is powered from LDO2.
Table 1. LDO Default Voltages
LDO
Function
mA
Default Voltage (V)
Startup Default
Enable Control
1
CORE
300
1.8
ON
SI
2
DIGI
300
3.0
ON
-
3
ANA
80
3.0
ON
SI
4
TCXO
80
3.0
OFF
TCXO_EN
5
RX
150
3.0
OFF
RX_EN
6
TX
150
3.0
OFF
TX_EN
7
GP
150
3.0
OFF
SI
Table 2. LDO Output Voltages Selectable via Serial Interface
LDO
mA
1.5
1.8
1.85
2.5
2.6
2.7
2.75
2.8
2.85
2.9
2.95
3.0
3.05
3.1
3.2
3.3
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
1
CORE
300
2
DIGI
300
3
ANA
80
4
TCXO
80
5
RX
150
6
TX
150
7
GP
150
+
+
+
+
+
+
+
+
+
+
LP3921 Pin Descriptions (1)
(1)
Type
(1)
Pin#
Name
1
LDO6
A
Description
LDO6 Output (TX)
2
TX_EN
DI
Enable control for LDO6 (TX). HIGH = Enable, LOW = Disable
3
LDO5
A
A LDO5 Output (RX)
Key: A=Analog; D=Digital; I=Input; DI/O=Digital-Input/Output; G=Ground; O=Output; P=Power
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
5
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
LP3921 Pin Descriptions(1) (continued)
Pin#
Name
Type (1)
4
VIN2
P
Battery Input for LDO3 - LDO7
5
LDO7
A
LDO7 Output (GP)
6
OUT+
AO
Differential output +
7
VDD
P
8
OUT-
AO
Differential output -
9
IN+
AI
Differential input +
10
IN-
AI
Differential input -
11
GND
G
Analog Ground Pin
12
BYPASS
A
Amplifier bypass cap
13
LDO4
A
LDO4 Output (TCXO)
14
LDO3
A
LDO3 Output (ANA)
15
LDO2
A
LDO2 Output (DIGI)
16
LDO1
A
LDO1 Output (CORE)
17
VIN1
P
Battery Input for LDO1 and LDO2
18
GNDA
G
Analog Ground pin
Description
DC power input to audio amplifier
SDA
DI/O
20
SCL
DI
Serial Interface Clock input. External pull up resistor is needed. (typ. 1.5k)
21
BATT
P
Main battery connection. Used as a power connection for current delivery to the battery.
22
CHG_IN
P
DC power input to charger block from wall or car power adapters.
23
PWR_ON
DI
Power up sequence starts when this pin is set HIGH. Internal 500k. pull-down resistor.
IMON
A
Charge current monitor output. This pin presents an analog voltage representation of the
25
PS_HOLD
DI
Input for power control from external processor/controller.
26
TCXO_EN
DI
Enable control for LDO4 (TX). HIGH = Enable, LOW = Disable.
27
HF_PWR
DI
Power up sequence starts when this pin is set HIGH. Internal 500k. pull-down resistor.
28
VSS
G
Digital Ground pin
29
PON_N
DO
Active low signal is PWR_ON inverted.
RESET_N
DO
Reset Output. Pin stays LOW during power up sequence. 60 ms after LDO1 (CORE) is
stable this pin is asserted HIGH.
31
ACOK_N
DO
AC Adapter indicator, LOW when 4.5V- 6.0V present at CHG_IN.
32
RX_EN
DI
Enable control for LDO5 (RX). HIGH = Enable, LOW = Disable.
19
24
Serial Interface, Data Input/Output Open Drain output, external pull up resistor is needed.
(typ. 1.5k)
input charging current. VIMON (mV) = (2.47 x ICHG)(mA).
30
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
6
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
Absolute Maximum Ratings (1) (2)
−0.3 to +6.5V
CHG-IN
−0.3 to +6.0V
VBATT =VIN1/2, BATT, VDD, HF_PWR
−0.3 to VBATT +0.3V, max 6.0V
All other Inputs
Junction Temperature (TJ-MAX)
150°C
Storage Temperature
−40°C to +150°C
Max Continuous Power Dissipation
(PD-MAX) (3)
Internally Limited
ESD
(4)
BATT, VIN1, VIN2, VDD, HF_PWR, CHG_IN, PWR_ON
8 kV HBM
All other pins
2 kV HBM
(1)
(2)
(3)
(4)
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is verified. Operating Ratings do not imply verified performance limits. For verified performance limits and
associated test conditions, see the Electrical Characteristics tables.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
Internal Thermal Shutdown circuitry protects the device from permanent damage.
The human-body model is 100 pF discharged through 1.5 kΩ. The machine model is a 200 pF capacitor discharged directly into each
pin, MIL-STD-883 3015.7.
Operating Ratings (1) (2)
CHG_IN
(3)
4.5 to 6.0V
VBATT =VIN1/2, BATT, VDD
3.0 to 5.5V
HF_PWR, PWR_ON
0V to 5.5V
ACOK_N, SDA, SCL, RX_EN,
TX_EN, TCXO_EN, PS_HOLD,
RESET_N
0V to (VLDO2 + 0.3V)
All other pins
0V to (VBATT + 0.3V)
−40°C to +125°C
Junction Temperature (TJ)
Ambient Temperature (TA)
(4)
(1)
(2)
(3)
(4)
-40 to 85°C
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is verified. Operating Ratings do not imply verified performance limits. For verified performance limits and
associated test conditions, see the Electrical Characteristics tables.
All voltages are with respect to the potential at the GND pin.
Full-charge current is specified for CHG_IN = 4.5 to 6.0V. At higher input voltages, increased power dissipation may cause the thermal
regulation to limit the current to a safe level, resulting in longer charging time.
Care must be exercised where high power dissipation is likely. The maximum ambient temperature may have to be derated. Like the
Absolute Maximum power dissipation, the maximum power dissipation for operation depends on the ambient temperature. In
applications where high power dissipation and/or poor thermal dissipation exists, the maximum ambient temperature may have to be
derated. Maximum ambient temperature (TA_MAX) is dependent on the maximum power dissipation of the device in the application
(PD_MAX), and the junction to ambient thermal resistance of the device/package in the application (θJA), as given by the following
equation:TA_MAX = TJ_MAX-OP – (θJA X PDMAX ).
Thermal Properties
(1)
Junction to Ambient
Thermal Resistance θJA
4L Jedec Board
(1)
30° C/W
Junction-to-ambient thermal resistance (θJA) is taken from thermal modelling result, performed under the conditions and guidelines set
forth in the JEDEC standard JESD51-7. The value of (θJA) of this product could fall within a wide range, depending on PWB material,
layout, and environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care
must be paid to thermal dissipation issues in board design.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
7
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
General Electrical Characteristics
Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 µF, CLDOX=1 µF. Typical values and
limits appearing in normal type apply for TJ = 25°C. Limits appearing in boldface type apply over the entire junction
temperature range for operation, TA = TJ = −40°C to +125°C. (1)
Symbol
IQ(STANDBY)
Parameter
Standby Supply
Current
Condition
Typ
VIN = 3.6V, UVLO on, internal logic
circuit on, all other circuits off
2
Limit
Min
Max
Units
5
µA
3.0
V
POWER MONITOR FUNCTIONS
Battery Under-Voltage Lockout
VUVLO-R
Under Voltage Lockout
VIN Rising
2.85
2.7
THERMAL SHUTDOWN
Higher Threshold
(2)
160
°C
LOGIC AND CONTROL INPUTS
VIL
Input Low Level
PS_HOLD, SDA, SCL, RX_EN,
TCXO_EN, TX_EN (2)
0.25*
V
VLDO2
PWR_ON, HF_PWR
0.25*
(2)
V
VBATT
VIH
Input High Level
PS_HOLD, SDA, SCL, RX_EN,
TCXO_EN, TX_EN
0.75*
V
VLDO2
(2)
PWR_ON, HF_PWR
0.75*
(2)
V
VBATT
IIL
Logic Input Current
RIN
Input Resistance
All logic inputs except PWR_ON
and HF_PWR
-5
+5
µA
0V ≤ VINPUT ≤ VBATT
PWR_ON, HF_PWR Pull-Down
resistance to GND
500
kΩ
LOGIC AND CONTROL OUTPUTS
VOL
Output Low Level
VOH
Output High Level
PON_N, RESET_N, SDA,
ACOK_N
0.25*
IOUT = 2 mA
V
VLDO2
PON_N, RESET_N, ACOK_N
0.75*
IOUT = -2 mA
VLDO2
V
(Not applicable to Open Drain
Output SDA)
(1)
(2)
All limits are verified. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and
cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process
control.
Specified by design.
LDO1 (CORE) Electrical Characteristics
Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 µF, CLDOX=1 µF. Note VINMIN is the
greater of 3.0V or VOUT1+ 0.5V. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in
boldface type apply over the entire junction temperature range for operation, TA = TJ = −40°C to +125°C. (1)
Symbol
VOUT1
(1)
8
Parameter
Condition
Output Voltage
Accuracy
IOUT1 = 1 mA, VOUT1= 3.0V
Output Voltage
Default
Typ
1.8
Limit
Min
Max
−2
+2
−3
+3
Units
%
V
All limits are verified. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and
cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process
control.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
LDO1 (CORE) Electrical Characteristics (continued)
Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 µF, CLDOX=1 µF. Note VINMIN is the
greater of 3.0V or VOUT1+ 0.5V. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in
boldface type apply over the entire junction temperature range for operation, TA = TJ = −40°C to +125°C. (1)
Symbol
IOUT1
Parameter
Condition
Output Current
VINMIN ≤ VIN ≤ 5.5V
Output Current Limit
VOUT1 = 0V
VDO1
Dropout Voltage
IOUT1 = 300 mA
ΔVOUT1
Line Regulation
VINMIN ≤ VIN ≤ 5.5V
Typ
Limit
Min
Max
Units
300
mA
310
mV
600
(2)
220
2
mV
IOUT1 = 1 mA
Load Regulation
en1
1 mA≤ IOUT1 ≤ 300 mA
Output Noise Voltage 10 Hz≤ f≤ 100 kHz,
COUT = 1 µF
PSRR
tSTART-UP
TTransient
(2)
(3)
(4)
10
mV
45
µVRMS
65
dB
(3)
Power Supply
Rejection Ratio
F = 10 kHz, COUT = 1 µF
Start-Up Time from
Internal Enable
COUT = 1 µF, IOUT1 = 300 mA
Start-Up Transient
Overshoot
COUT = 1 µF,
IOUT1 = 300 mA
IOUT1 = 20 mA
(3)
60
170
µs
60
120
mV
(4)
(3)
Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply in cases it implies operation with an input voltage below the 3.0V minimum appearing under Operating
Ratings. For example, this specification does not apply for devices having 1.5V outputs because the specification would imply operation
with an input voltage at or about 1.5V.
Specified by design.
Specified by design.
LDO2 (DIGI) Electrical Characteristics
Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 µF, CLDOX=1 µF. Note VINMIN is the
greater of 3.0V or VOUT2+ 0.5V. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in
boldface type apply over the entire junction temperature range for operation, TA = TJ = −40°C to +125°C. (1)
Symbol
VOUT2
IOUT2
Parameter
Condition
Output Voltage
Accuracy
IOUT2 = 1 mA, VOUT2= 3.0V
Output Voltage
Default
Output Current
VINMIN ≤ VIN ≤ 5.5V
Typ
Limit
Min
Max
−2
+2
−3
+3
Units
%
3
Output Current Limit
VOUT2 = 0V
VDO2
Dropout Voltage
IOUT2 = 300 mA
ΔVOUT2
Line Regulation
VINMIN ≤ VIN ≤ 5.5V
V
300
mA
310
mV
600
(2)
220
2
mV
IOUT2 = 1mA
Load Regulation
en2
1 mA≤ IOUT2 ≤ 300 mA
Output Noise Voltage 10 Hz≤ f≤ 100 kHz,
COUT = 1 µF
PSRR
(1)
(2)
(3)
Power Supply
Rejection Ratio
10
mV
45
µVRMS
65
dB
(3)
F = 10 kHz, COUT = 1 µF
IOUT2 = 20 mA
(3)
All limits are verified. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and
cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process
control.
Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply in cases it implies operation with an input voltage below the 3.0V minimum appearing under Operating
Ratings. For example, this specification does not apply for devices having 1.5V outputs because the specification would imply operation
with an input voltage at or about 1.5V.
Specified by design.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
9
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
LDO2 (DIGI) Electrical Characteristics (continued)
Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 µF, CLDOX=1 µF. Note VINMIN is the
greater of 3.0V or VOUT2+ 0.5V. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in
boldface type apply over the entire junction temperature range for operation, TA = TJ = −40°C to +125°C. (1)
Symbol
Parameter
Condition
Typ
Limit
Min
Max
Units
tSTART-UP
Start-Up Time from
Shutdown
COUT = 1 µF, IOUT2 = 300 mA
(3)
40
60
µs
tTransient
Start-Up Transient
Overshoot
COUT = 1 µF, IOUT2 = 300 mA
(3)
5
30
mV
LDO3 (ANA), LDO4 (TCXO) Electrical Characteristics
Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 µF, CLDOX=1 µF. TCXO_EN high. Note
VINMIN is the greater of 3.0V or VOUT3/4 + 0.5V. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits
appearing in boldface type apply over the entire junction temperature range for operation, TA = TJ = −40°C to +125°C. (1)
Symbol
VOUT3, VOUT4
Parameter
Condition
Output Voltage
Accuracy
IOUT3/4 = 1 mA, VOUT3/4= 3.0V
Output Voltage
LDO3 default
3
LDO4 default
3
Output Current
VINMIN ≤ VIN ≤ 5.5V
Output Current Limit
VOUT3/4 = 0V
VDO3, VDO4
Dropout Voltage
IOUT3/4 = 80 mA
ΔVOUT3 , ΔVOUT4
Line Regulation
VINMIN ≤ VIN ≤ 5.5V
IOUT3, IOUT4
Typ
Limit
Min
Max
−2
+2
−3
+3
Units
%
V
80
mA
310
mV
160
(2)
220
2
mV
IOUT3/4 = 1 mA
Load Regulation
1mA≤ IOUT3/4 ≤ 80 mA
Output Noise Voltage 10 Hz ≤ f ≤ 100 kHz,
en3,en4
COUT = 1 µF
PSRR
5
mV
45
µVRMS
65
dB
(3)
Power Supply
Rejection Ratio
F = 10 kHz, COUT = 1 µF
tSTART-UP
Start-Up Time from
Enable (3)
COUT = 1 µF, IOUT3/4 = 80mA
40
60
µs
tTransient
Start-Up Transient
Overshoot
COUT = 1µF, IOUT3/4 = 80 mA
5
30
mV
(1)
(2)
(3)
10
IOUT3/4 = 20 mA
(3)
(3)
All limits are verified. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and
cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process
control.
Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply in cases it implies operation with an input voltage below the 3.0V minimum appearing under Operating
Ratings. For example, this specification does not apply for devices having 1.5V outputs because the specification would imply operation
with an input voltage at or about 1.5V.
Specified by design.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
LDO5 (RX), LDO6 (TX), LDO7 (GP) Electrical Characteristics
Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 µF, CLDOX=1 µF. RX_EN, TX_EN high.
LDO7 Enabled via Serial Interface. Note VINMIN is the greater of 3.0V or VOUT5/6/7 + 0.5V. Typical values and limits appearing in
normal type apply for TJ = 25°C. Limits appearing in boldface type apply over the entire junction temperature range for
operation, TA = TJ = −40°C to +125°C. (1)
Symbol
VOUT5, VOUT6,
VOUT7
Parameter
Output Voltage
Default Output
Voltage
IOUT5, IOUT6,
IOUT7
Condition
IOUT5/6/7 = 1mA, VOUT5/6/7= 3.0V
LDO5
3
LDO6
3
LDO7
3
Output Current
VINMIN ≤ VIN ≤ 5.5V
Output Current Limit
VOUT5/6/7 = 0V
IOUT5/6/7 = 150 mA
ΔVOUT5, ΔVOUT6,
ΔVOUT7
VINMIN ≤ VIN ≤ 5.5V
(2)
Max
−2
+2
−3
+3
Units
%
V
200
150
mA
280
mV
2
1mA≤ IOUT5/6/7 ≤ 150 mA
Output Noise Voltage 10 Hz ≤ f ≤ 100 kHz,
COUT = 1 µF
PSRR
Min
mV
IOUT5/6/7 = 1 mA
Load Regulation
en5, en6, en7
Limit
300
VDO5, VDO6, VDO7 Dropout Voltage
Line Regulation
Typ
10
mV
45
µVRMS
65
dB
(3)
Power Supply
Rejection Ratio
F = 10 kHz, COUT = 1 µF
tSTART-UP
Start-Up Time from
Enable
COUT = 1 µF, IOUT5/6/7 = 150 mA
40
60
µs
tTransient
Start-Up Transient
Overshoot
COUT = 1 µF, IOUT5/6/7 = 150 mA
5
30
mV
(1)
(2)
(3)
(4)
IOUT5/6/7 = 20 mA
(3)
(3)
(4)
All limits are verified. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and
cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process
control.
Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply in cases it implies operation with an input voltage below the 3.0V minimum appearing under Operating
Ratings. For example, this specification does not apply for devices having 1.5V outputs because the specification would imply operation
with an input voltage at or about 1.5V.
Specified by design.
Internal Thermal Shutdown circuitry protects the device from permanent damage.
Charger Electrical Characteristics
Unless otherwise noted, VCHG-IN = 5V, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V.CCHG_IN = 10 µF. Charger set to default settings
unless otherwise noted. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in boldface
type apply over the entire junction temperature range for operation, TA = TJ = −25°C to +85°C. (1) (2)
Symbol
VCHG-IN
Parameter
Input Voltage Range
Condition
Typ
(3)
Operating Range
VOK_CHG
(1)
(2)
(3)
CHG_IN OK trip-point
VCHG_IN - VBATT (Rising)
200
VCHG_IN - VBATT (Falling)
50
Limit
Min
Max
4.5
6.5
4.5
6
Units
V
mV
All limits are verified. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and
cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process
control.
Junction-to-ambient thermal resistance (θJA) is taken from thermal modelling result, performed under the conditions and guidelines set
forth in the JEDEC standard JESD51-7. The value of (θJA) of this product could fall within a wide range, depending on PWB material,
layout, and environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care
must be paid to thermal dissipation issues in board design.
Specified by design.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
11
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
Charger Electrical Characteristics (continued)
Unless otherwise noted, VCHG-IN = 5V, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V.CCHG_IN = 10 µF. Charger set to default settings
unless otherwise noted. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in boldface
type apply over the entire junction temperature range for operation, TA = TJ = −25°C to +85°C. (1)(2)
Symbol
VTERM
ICHG
Parameter
Condition
Battery Charge Termination
voltage
Default
VTERM voltage tolerance
TJ = 0°C to 85°C
Typ
Limit
Min
Max
4.2
Units
V
-1
+1
Fast Charge Current Accuracy ICHG = 450 mA
-10
+10
%
%
Programmable full-rate charge 6.0V ≥ VCHG_IN ≥ 4.5V
current range (default 100 mA)
VBATT < (VCHG_IN - VOK_CHG)
50
950
mA
40
60
mA
VFULL_RATE < VBATT < VTERM
(4)
Default
100
Charge current programming
step
50
IPREQUAL
Pre-qualification current
VBATT = 2V
ICHG_USB
CHG_IN programmable
current in USB mode
5.5V ≥ VCHG_IN ≥
4.5V
50
Low
100
VBATT < (VCHG_IN
- VOK_CHG)
VFULL_RATE <
VBATT < VTERM
mA
High
450
Default = 100 mA
100
VFULL_RATE
Full-rate qualification threshold VBATT rising, transition from pre-qual to full-rate
charging
3
IEOC
End of Charge Current, % of
full-rate current
0.1C option selected
10
VRESTART
Restart threshold voltage
VBATT falling, transition from EOC to full-rate
charge mode. Default options selected - 4.05V
4.05
IMON
IMON Voltage 1
ICHG = 100 mA
0.247
IMON Voltage 2
ICHG = 450 mA
1.112
TREG
Regulated junction
temperature
(5)
115
2.9
3.1
V
%
3.97
4.13
0.947
1.277
V
V
°C
Detection and Timing (5)
TPOK
Power OK deglitch time
VBATT < (VCC - VOK_CHG)
32
TPQ_FULL
Deglitch time
Pre-qualification to full-rate charge transition
230
mS
TCHG
Charge timer
Precharge mode
1
Hrs
TEOC
Deglitch time for end-ofcharge transition
Charging Timeout
(4)
(5)
12
mS
5
230
mS
Full-charge current is specified for CHG_IN = 4.5 to 6.0V. At higher input voltages, increased power dissipation may cause the thermal
regulation to limit the current to a safe level, resulting in longer charging time.
Specified by design.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
Audio Electrical Characteristics
Unless otherwise noted, VDD= 3.6V Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in
boldface type apply over the entire junction temperature range for operation, TA= TJ = −25°C to +85°C. (1)
Symbol
Paramater
Conditions
Typical
Limit
Min
Max
Units
PO
Output Power
THD = 1% (max);
f = 1 kHz, RL = 8Ω
0.375
W
THD + N
Total Harmonic Distortion
+ Noise
PO = 0.25 Wrms;
f = 1 kHz
0.02
%
Vripple = 200 mVPP
PSRR
Power Supply Rejection
Ratio
f = 217 Hz
85
f = 1 kHz
85
dB
73
CMRR
Common-Mode Rejection
Ratio
f = 217 Hz,
VCM = 200 mVPP
50
dB
VOS
Output Offset
VacINput = 0V
4
mV
(1)
All limits are verified. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and
cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process
control.
Serial Interface
Unless otherwise noted, VIN ( = VIN1 = VIN2 = BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 µF, CLDOX=1 µF, and VLDO2 (DIGI)
≥ 1.8V. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in boldface type apply over
the entire junction temperature range for operation, TA= TJ = −40°C to +125°C. (1) (2)
Symbol
Parameter
Condition
Typ
Limit
Min
Max
fCLK
Clock Frequency
tBF
Bus-Free Time between
START and STOP
1.3
µs
tHOLD
Hold Time Repeated START
Condition
0.6
µs
tCLK-LP
CLK Low Period
1.3
µs
tCLK-HP
CLK High Period
0.6
µs
tSU
Set-Up Time Repeated
START Condition
0.6
µs
tDATA-HOLD
Data Hold Time
50
ns
tDATA-SU
Data Set-Up Time
100
ns
tSU
Set-Up Time for STOP
Condition
0.6
µs
tTRANS
Maximum Pulse Width of
Spikes that Must be
Suppressed by the Input
Filter of both DATA & CLK
Signals
(1)
(2)
400
Units
50
kHz
ns
All limits are verified. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and
cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process
control.
Specified by design.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
13
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
TECHNICAL DESCRIPTION
DEVICE POWER UP AND SHUTDOWN TIMING
PWR_ON
30 ms Debounce time
PS_HOLD needs to be asserted while
PWR_ON is high.
PS_HOLD
LDO1
87% Reg
< 200 Ps
LDO2
87% Reg
60 ms
RESET
2
I C Control
LDO3
LDO7
RX_EN, TX_EN,
TCXO_EN
LDO4,5,6
Note: Serial I/F commands only take place
after PS_HOLD is asserted.
Figure 2. Device Power Up Logic Timing: PWR_ON
14
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
If charger is connected (CHG_IN) or HF_PWR is
applied, then both events are filtered for 320 ms
before enabling LDO1
320 ms
CHG_IN
PS_HOLD needs to be asserted within 1200 ms after
CHG_IN or HF_PWR rising edge has been detected.
(HF_PWR level detected for LP3921)
HF_PWR
1.2s
Debounce time before normal start up sequence, 320 ms.
PS_HOLD high < 1.2s from I/P detection
PS_HOLD
LDO1
87% Reg
< 200 Ps
LDO2
87% Reg
60 ms
RESET
2
I C Control
LDO3
LDO7
RX_EN, TX_EN,
TCXO_EN
LDO4,5,6
Note: Serial I/F commands only take place
after PS_HOLD is asserted.
Figure 3. Device Power Up Logic Timing: CHG_IN, HF_PWR
START UP
Device start is initiated by any of the 3 input signals, PWR_ON, HF_PWR and CHG_IN.
PWR_ON
When PWR_ON goes high the device will remain powered up, a PS_HOLD applied will allow the device to
remain powered after the PWR_ON signal has gone low.
HF_PWR, CHGIN
PS_HOLD needs to be asserted within 1200 ms after a CHG_IN or HF_PWR rising edge has been detected. For
applications where a level sensitive input is required the LP3921 is available with a level detect input at
HF_PWR.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
15
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
If charger is connected (CHG_IN) or HF_PWR is
applied, then both events are filtered for 320 ms
320 ms before enabling LDO1
CHG_IN
PS_HOLD needs to be asserted within 1200 ms
after HF_PWR, or CHG_IN rising edge has been
detected.
1.2s
HF_PWR
Either HF_PWR or CHG_IN will enable LDO1
If no enabling signal is high on
the rising edge of PS_HOLD,
shutdown will occur.
PS_HOLD
87%
LDO1
200 Ps
87% Reg
LDO2
60 ms
RESET
Figure 4. LP3921 Power On Behavior (Failed PS_Hold)
35 ms
PS_HOLD
RESET
If PS_HOLD is low 35 ms after initially going low,
then LDO2-7 are shutdown
LDO2 - 7
LDO1 is shutdown 40 Ps after other
LDO's are shutdown
LDO1
40 Ps
Figure 5. LP3921 Normal Shutdown Behavior
LP3921 Serial Port Communication
Slave Address Code 7h’7E
16
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
Table 3. Control Registers (1)
Addr
Register
(default
value)
8h'00
D7
D6
D5
D4
D3
D2
D1
D0
OP_EN
(0000 0101)
X
X
X
X
LDO7_EN
LDO3_EN
X
LDO1_EN
8h'01
LDO1PGM
O/P
(0000 0001)
X
X
X
X
V1_OP[3]
V1_OP[2]
V1_OP[1]
V1_OP[0]
8h'02
LDO2PGM
O/P
(0000 1011)
X
X
X
X
V2_OP[3]
V2_OP[2]
V2_OP[1]
V2_OP[0]
8h'03
LDO3PGM
O/P
(0000 1011)
X
X
X
X
V3_OP[3]
V3_OP[2]
V3_OP[1]
V3_OP[0]
8h'04
LDO4PGM
O/P
(0000 1011)
X
X
X
X
V4_OP[3]
V4_OP[2]
V4_OP[1]
V4_OP[0]
8h'05
LDO5PGM
O/P
(0000 1011)
X
X
X
X
V5_OP[3]
V5_OP[2]
V5_OP[1]
V5_OP[0]
8h'06
LDO6PGM
O/P
(0000 1011)
X
X
X
X
V6_OP[3]
V6_OP[2]
V6_OP[1]
V6_OP[0]
8h'07
LDO7PGM
O/P
(0000 1011)
X
X
X
X
V7_OP[3]
V7_OP[2]
V7_OP[1]
V7_OP[0]
8h'0C
STATUS
(0000 0000)
PWR_ON_
TRIB
HF_PWR_
TRIG
CHG_IN_
TRIG
X
X
X
X
X
8h'10
CHGCNTL1
(0000 1001)
USBMODE
_EN
CHGMODE
_EN
Force EOC
TOUT_
doubling
EN_Tout
En_EOC
X
EN_CHG
8h'11
CHGCNTL2
(0000 0001)
X
X
X
Prog_
ICHG[4]
Prog_
ICHG[3]
Prog_
ICHG[2]
Prog_
ICHG[1]
Prog_
ICHG[0]
8h'12
CHGCNTL3
(0001 0010)
X
X
VTERM[1]
VTERM[0]
Prog_
EOC[1]
Prog_
EOC[0]
Prog_
VRSTRT[1]
Prog_
VRSTRT[0]
8h'13
CHGSTATUS1
Batt_Over_
Out
CHGIN_
OK_Out
EOC
Tout_
Fullrate
Tout_
Prechg
LDO Mode
Fullrate
PRECHG
8h'14
CHGSTATUS2
X
X
X
X
X
X
Tout_
ConstV
Bad_Batt
8h'19
Audio_Amp
X
X
X
X
X
X
X
amp_en
X
APU_TSD_
EN
PS_HOLD
_DELAY
8h'1C
(1)
MISC Control1
X
X
X
X
X
X = Not used
Bold type = Bits are read-only type
Codes other than those shown in the table are disallowed.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
17
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
The following table summarizes the supported output voltages for the LP3921. Default voltages after startup are
highlighted in bold.
Table 4. LDO Output Voltage Programming
Data Code
LDOx PGM
O/P
LDO1
(V)
8h'00
1.5
LDO2
(V)
VLDO3
(V)
LDO4
(V)
LDO5
(V)
LDO6
(V)
1.5
LDO7
(V)
1.5
8h'01
1.8
1.8
1.8
8h'02
1.85
1.85
1.85
8h'03
2.5
2.5
2.5
2.5
8h'04
2.6
2.6
2.6
2.6
8h'05
2.7
2.7
2.7
2.7
2.7
2.7
2.7
8h'06
2.75
2.75
2.75
2.75
2.75
2.75
2.75
8h'07
2.8
2.8
2.8
2.8
2.8
2.8
2.8
8h'08
2.85
2.85
2.85
2.85
2.85
2.85
2.85
8h'09
2.9
2.9
2.9
2.9
2.9
2.9
2.9
8h'0A
2.95
2.95
2.95
2.95
2.95
2.95
2.95
8h'0B
3.0
3.0
3.0
3.0
3.0
3.0
3.0
8h'0C
3.05
3.05
3.05
3.05
3.05
3.05
3.05
8h'0D
3.1
3.1
3.1
3.1
8h'0E
3.2
3.2
3.2
3.2
8h'0F
3.3
3.3
3.3
3.3
The following table summarizes the supported charging current values for the LP3921. Default charge current
after startup is 100 mA.
Table 5. Charging Current Programming
18
Prog_Ichg[4]
Prog_Ichg[3
Prog_Ichg[2]
Prog_Ichg[1]
Prog_Ichg[0]
I_Charge I mA
0
0
0
0
0
50
0
0
0
0
1
100 (Default)
0
0
0
1
0
150
0
0
0
1
1
200
0
0
1
0
0
250
0
0
1
0
1
300
0
0
1
1
0
350
0
0
1
1
1
400
0
1
0
0
0
450
0
1
0
0
1
500
0
1
0
1
0
550
0
1
0
1
1
600
0
1
1
0
0
650
0
1
1
0
1
700
0
1
1
1
0
750
0
1
1
1
1
800
1
0
0
0
0
850
1
0
0
0
1
900
1
0
0
1
0
950
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
Table 6. Charging Termination Voltage Control
VTERM[1]
VTERM[0]
Termination Voltage (V)
0
0
4.1
0
1
4.2 (Default)
1
0
4.3
1
1
4.4
Table 7. End Of Charge Current Control (1)
(1)
PROG_EOC[1]
PROG_EOC[0]
End of Charge Current
0
0
0.1 (Default)
0
1
0.15C
1
0
0.2C
1
1
0.25C
Note: C is the set charge current.
Table 8. Charging Restart Voltage Programming
PROG_VRSTRT[1]
PROG_VRSTRT[1]
Restart Voltage(V)
0
0
VTERM - 50 mV
0
1
VTERM - 100 mV
1
0
VTERM - 150 mV
1
1
VTERM - 200 mV
Table 9. USB Charging Selection
USB_Mode_En
CHG_Mode_En
Mode
Current
0
0
Fast Charge
Default or Selection
1
0
Fast Charge
Default or Selection
0
1
USB
100 mA
1
1
USB
450 mA
Battery Charge Management
A charge management system allowing the safe charge and maintenance of a Li-Ion battery is implemented on
the LP3921. This has a CC/CV linear charge capability with programmable battery regulation voltage and end of
charge current threshold. The charge current in the constant current mode is programmable and a maintenance
mode monitors for battery voltage drop to restart charging at a preset level. A USB charging mode is also
available with 2 charge current levels.
CHARGER FUNCTION
Following the correct detection of an input voltage at the charger pin the charger enters a pre-charge mode. In
this mode a constant current of 50 mA is available to charge the battery to 3.0V. At this voltage level the charge
management applies the default (100 mA) full rate constant current to raise the battery voltage to the termination
voltage level (default 4.2V). The full rate charge current may be programmed to a different level at this stage.
When termination voltage (VTERM) is reached, the charger is in constant voltage mode and a constant voltage of
4.2V is maintained. This mode is complete when the end of charge current (default 0.1C) is detected and the
charge management enters the maintenance mode. In maintenance mode the battery voltage is monitored for
the restart level (4.05V at the default settings) and the charge cycle is re-initiated to re-establish the termination
voltage level. For start up the EOC function is disabled. This function should be enabled once start up is
complete and a battery has been detected. EOC is enabled via register CHGCNTL1, Table 10.
The full rate constant current rate of charge may be programmed to 19 levels from 50 mA to 950 mA. These
values are given in Table 5 and Table 13.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
19
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
The charge mode may be programmed to USB mode when the charger input is applied and the battery voltage is
above 3.0V. This provides two programmable current levels of 100 mA and 450 mA for a USB sourced supply
input at CHG_IN. Table 9.
EOC
EOC is disabled by default and should be enabled when the system processor is awake and the system detects
that a battery is present.
PROGRAMMING INFORMATION
Table 10. Register Address 8h'10: CHGCNTL1
BIT
NAME
2
En_EOC
FUNCTION
Enables the End Of Charge current level threshold detection.
When set to '0' the EOC is disabled.
The End Of Charge current threshold default setting is at 0.1C. This EOC value is set relative to C the set full
rate constant current. This threshold can be set to 0.1C, 0.15C, 0.2C or 0.25C by changing the contents of the
PROG_EOC[1:0] register bits.
Table 11. Register Address 8h'12: CHGCNTL3
BIT
NAME
2
Prog_EOC[0]
3
Prog_EOC[1]
FUNCTION
Set the End Of Charge Current.
See Table 7.
TERMINATION AND RESTART
The termination and restart voltage levels are determined by the data in the VTERM[1:0] and PROG_VSTRT[1:0]
bits in the control register. The restart voltage is programmed relative to the selected termination voltage.
The Termination voltages available are 4.1V, 4.2V (default), 4.3V, and 4.4V.
The Restart voltages are determined relative to the termination voltage level and may be set to 50 mV, 100 mV,
150 mV (default), and 200 mV below the set termination voltage level.
Table 12. Register Address 8h'12: CHGCNTL3
20
BIT
NAME
4
VTERM[0]
5
VTERM[1]
0
VRSTR[0]
1
VRSTR[1]
FUNCTION
Set the charging termination voltage.
See Table 6.
Set the charging restart voltage. See Table 8.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
CHARGER FULL RATE CURRENT
Programming Information
Table 13. Register Address 8h'11: CHGCNTL2
Data BITs
HEX
NAME
FUNCTION
000[00000]
00
Prog_ICHG
50 mA
000[00001]
01
100 mA
000[00010]
02
150 mA
000[00011]
03
200 mA
000[00100]
04
250 mA
000[00101]
05
300 mA
000[00110]
06
350 mA
000[00111]
07
400 mA
000[01000]
08
450 mA
000[01001]
09
500 mA
000[01010]
0A
550 mA
000[01011]
0B
600 mA
000[01100]
0C
650 mA
000[01101]
0D
700 mA
000[01110]
0E
750 mA
000[01111]
0F
800 mA
000[10000]
10
850 mA
000[10001]
11
900 mA
000[10010]
12
950 mA
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
21
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
From any mode:
VCHG_IN < 4.5V
or VCHG_IN > 6.0V
or disabled via serial interface.
Charger OFF
Zero Current
4.5V < VCHG_IN < 6.0V
Yes
Pre-Charge mode
50mA Constant current
VBATT > 3.0V
No
Yes
Full-Rate Charge mode
Constant Current (ICHG)
VBATT = VTERM
No
Yes
Full-Rate Charge mode
Constant Voltage (VTERM)
ICHG < EOC
No
Yes
Maintenance mode
Zero current
VBATT < VRSTRT
No
Yes
Figure 6. Simplified Charger Functional State Diagram (EOC is enabled)
The charger operation may be depicted by the following graphical representation of the voltage and current
profiles.
22
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
Prequalification to Fast
Charge transition
1.0 C
Transition to Constant
Voltage-mode
Maintenance charging
starts
VTERM
Battery Voltage /
Charging Current
VRSTRT
3.0V
Charging current
Charging current
EOC
50 mA
Time
Figure 7. Charge Cycle Diagram
Further Charger Register Information
CHARGER CONTROL REGISTER 1
Table 14. Register Address 8h'10: CHGCNTL1
BIT
NAME
FUNCTION (if bit = '1')
7
USB_MODE
_EN
Sets the Current Level in USB mode.
6
CHG_MODE
_EN
Forces the charger into USB mode when active high.
If low, charger is in normal charge mode.
5
FORCE
_EOC
Forces an EOC event.
4
TOUT_
Doubling
Doubles the timeout delays for all timeout signals.
3
EN_Tout
Enables the timeout counters. When set to '0' the timeout counters
are disabled.
2
EN_EOC
Enables the End of Charge current level threshold detection.
When set to '0' the functions are disabled.
1
Set_
LDOmode
Forces the charger into LDO mode.
0
EN_CHG
Charger enable.
Table 15. Register Address 8h'13: CHGSTATUS1
BIT
NAME
7
BAT_OVER
_OUT
FUNCTION (if bit = '1')
6
CHGIN_
OK_Out
5
EOC
4
Tout_
Fullrate
3
Tout_
Precharge
Set after timeout for precharge mode.
2
LDO_Mode
This bit is disabled in LP3921. Contact NSC sales if this option is
required as in LP3918–L.
1
Fullrate
Is set when battery voltage exceeds 4.7V.
Is set when a valid input voltage is detected at CHG_IN pin.
Is set when the charging current decreases below the
programmed End Of Charge level.
Set after timeout on full rate charge.
Set when the charger is in CC/CV mode.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
23
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
Table 15. Register Address 8h'13: CHGSTATUS1 (continued)
BIT
NAME
0
PRECHG
FUNCTION (if bit = '1')
Set during precharge.
Charger Status Register 2 Read only
Table 16. Register Address 8h'13: CHGSTATUS2
BIT
NAME
1
Tout_ConstV
FUNCTION (if bit = '1')
0
BAD_BATT
Set after timeout in CV phase.
Set at bad battery state.
IMON CHARGE CURRENT MONITOR
Charge current is monitored within the charger section and a proportional voltage representation of the charge
current is presented at the IMON output pin. The output voltage relationship to the actual charge current is
represented in the following graph and by the equation:
VIMON(mV) = (2.47 x ICHG)(mA)
IMON VOLTAGE (V)
1.729
1.235
0.247
100
500
700
CHARGE CURRENT (mA)
Figure 8. IMON Voltage vs. Charge Current
Note that this function is not available if there is no input at CHG_IN or if the charger is off due to the input at
CHG_IN being less than the compliance voltage.
LDO Information
OPERATIONAL INFORMATION
The LP3921 has 7 LDO's of which 3 are enabled by default, LDO's 1,2 and 3 are powered up during the power
up sequence. LDO's 4, 5 and 6 are separately, externally enabled and will follow LDO2 in start up if their
respective enable pin is pulled high. LDO2, LDO3 and LDO7 can be enabled/disabled via the serial interface.
LDO2 must remain in regulation otherwise the device will power down. While LDO1 is enabled this must also be
in regulation for the device to remain powered. If LDO1 is disabled via I2C interface the device will not shut down.
INPUT VOLTAGES
There are two input voltage pins used to power the 7 LDO's on the LP3921. VIN2is the supply for LDO3, LDO4,
LDO5, LDO6 and LDO7. VIN1is the supply for LDO1 and LDO2.
24
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
PROGRAMMING INFORMATION
Enable via Serial Interface
Table 17. Register Address 8h'00: OP_EN
BIT
NAME
0
LDO1_EN
2
LDO3_EN
3
LDO7_EN
FUNCTION
Bit set to '0' - LDO disabled
Bit set to '1' - LDO enabled
Note that the default setting for this Register is [0000 0101]. This shows that LDO1 and LDO3 are enabled by
default whereas LDO7 is not enabled by default on start up.
Table 18. LDO Output Programming (1)
Register Add (hex)
Name
Data Range (hex)
01
LDO1PGM
O/P
03 - 0F
1.5V to 3.3V
(def. 1.8V)
02
LDO2PGM
O/P
00 - 0F
2.5V to 3.3V
(def 3.0V)
03
LDO3PGM
O/P
05 - 0C
2.7V to 3.05V
(def 3.0V)
04
LDO4PGM
O/P
00 - 0F
1.5V to 3.3V
(def 3.0V)
05
LDO5PGM
O/P
05 - 0C
2.7V to 3.05V
(def 3.0V)
06
LDO6PGM
O/P
05 - 0C
2.7V to 3.05V
(def 3.0V)
07
LDO7PGM
O/P
00 - 0F
1.5V to 3.3V
(def 3.0V)
(1)
Output Voltage
See Table 4 for full programmable range of values.
EXTERNAL CAPACITORS
The Low Drop Out Linear Voltage regulators on the LP3921 require external capacitors to ensure stable outputs.
The LDO's on the LP3921 are specifically designed to use small surface mount ceramic capacitors which require
minimum board space. These capacitors must be correctly selected for good performance
INPUT CAPACITOR
Input capacitors are required for correct operation. It is recommended that a 10 µF capacitor be connected
between each of the voltage input pins and ground (this capacitance value may be increased without limit). This
capacitor must be located a distance of not more than 1 cm from the input pin and returned to a clean analogue
ground. A ceramic capacitor is recommended although a good quality tantalum or film capacitor may be used at
the input.
WARNING
Important: Tantalum capacitors can suffer catastrophic failures due to surge
current when connected to a low-impedance source of power (like a battery or a
very large capacitor). If a tantalum capacitor is used at the input, it must be
guaranteed by the manufacturer to have surge current rating sufficient for the
application. There are no requirements for the ESR (Equivalent Series
Resistance) on the input capacitor, but tolerance and temperature coefficient
must be considered when selecting the capacitor to ensure the capacitance will
remain within its operational range over the entire operating temperature range
and conditions.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
25
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
OUTPUT CAPACITOR
Correct selection of the output capacitor is critical to ensure stable operation in the intended application. The
output capacitor must meet all the requirements specified in the recommended capacitor table over all conditions
in the application. These conditions include DC-bias, frequency and temperature. Unstable operation will result if
the capacitance drops below the minimum specified value.
The LP3921 is designed specifically to work with very small ceramic output capacitors. The LDO's on the LP3921
are specifically designed to be used with X7R and X5R type capacitors. With these capacitors selection of the
capacitor for the application is dependant on the range of operating conditions and temperature range for that
application. (See CAPACITOR CHARACTERISTICS).
It is also recommended that the output capacitor be placed within 1 cm from the output pin and returned to a
clean ground line.
CAPACITOR CHARACTERISTICS
The LDO's on the LP3921 are designed to work with ceramic capacitors on the input and output to take
advantage of the benefits they offer. For capacitance values around 1 µF, ceramic capacitors give the circuit
designer the best design options in terms of low cost and minimal area.
Generally speaking, input and output capacitors require careful understanding of the capacitor specification to
ensure stable and correct device operation. Capacitance value can vary with DC bias conditions as well as
temperature and frequency of operation.
CAP VALUE (% of NOM. 1 PF)
Capacitor values will also show some decrease over time due to aging. The capacitor parameters are also
dependant on the particular case size with smaller sizes giving poorer performance figures in general.
0603, 10V, X5R
100%
80%
60%
0402, 6.3V, X5R
40%
20%
0
1.0
2.0
3.0
4.0
5.0
DC BIAS (V)
Figure 9. DC Bias (V)
As an example, Figure 9 shows a typical graph showing a comparison of capacitor case sizes in a Capacitance
vs DC Bias plot. As shown in the graph, as a result of DC Bias condition the capacitance value may drop below
minimum capacitance value given in the recommended capacitor table (0.7 µF in this case). Note that the graph
shows the capacitance out of spec for 0402 case size capacitor at higher bias voltages. It is therefore
recommended that the capacitor manufacturers specifications for the nominal value capacitor are consulted for
all conditions as some capacitor sizes (e.g., 0402) may not be suitable in the actual application. Ceramic
capacitors have the lowest ESR values, thus making them best for eliminating high frequency noise. The ESR of
a typical 1 µF ceramic capacitor is in the range of 20 mΩ to 40 mΩ, and also meets the ESR requirements for
stability. The temperature performance of ceramic capacitors varies by type. Capacitor type X7R is specified with
a tolerance of ±15% over temperature range -55ºC to +125ºC. The X5R has similar tolerance over the reduced
temperature range -55ºC to +85ºC. Most large value ceramic capacitors ( Data from master [ ] Data from slave
REGISTER READ AND WRITE DETAIL
S
Slave Address
(7 bits)
'0' A
R/W
From Slave to Master
Control Register Add.
(8 bits)
Register Data
(8 bits)
A
A P
Data transferred, byte +
Ack
A - ACKNOWLEDGE (SDA Low)
S - START CONDITION
From Master to Slave
P - STOP CONDITION
Figure 14. Register Write Format
34
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
LP3921
www.ti.com
SNVS580A – AUGUST 2008 – REVISED MAY 2013
S
Slave Address
(7 bits)
'0' A
Control Register Add.
(8 bits)
A Sr
Slave Address
(7 bits)
R/W
'1' A
R/W
Register Data
(8 bits)
A/
P
NA
Data transferred, byte +
Ack/NAck
Direction of the transfer
will change at this point
A - ACKNOWLEDGE (SDA Low)
From Slave to Master
NA - ACKNOWLEDGE (SDA High)
From Master to Slave
S - START CONDITION
Sr - REPEATED START CONDITION
P - STOP CONDITION
Figure 15. Register Read Format
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
35
LP3921
SNVS580A – AUGUST 2008 – REVISED MAY 2013
www.ti.com
REVISION HISTORY
Changes from Original (May 2013) to Revision A
•
36
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 35
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LP3921
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LP3921SQ/NOPB
NRND
WQFN
RTV
32
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 85
L3921SQ
LP3921SQE/NOPB
ACTIVE
WQFN
RTV
32
250
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 85
L3921SQ
LP3921SQX/NOPB
NRND
WQFN
RTV
32
4500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 85
L3921SQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of