LP3986
www.ti.com
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
LP3986 Dual Micropower 150 mA Ultra Low-Dropout CMOS Voltage Regulators in DSBGA
Package
Check for Samples: LP3986
FEATURES
DESCRIPTION
•
•
The LP3986 is a 150 mA dual low dropout regulator
designed for portable and wireless applications with
demanding
performance
and
board
space
requirements.
1
2
•
•
•
•
Miniature 8-I/O DSBGA Package
Stable With 1µF Ceramic and High Quality
Tantalum Output Capacitors
Fast Turn-on
Two Independent Regulators
Logic Controlled Enable
Over Current and Thermal Protection
APPLICATIONS
•
•
•
•
CDMA Cellular Handsets
GSM Cellular Handsets
Portable Information Appliances
Portable Battery Applications
The LP3986 is stable with a small 1 µF ±30%
ceramic output capacitor requiring smallest possible
board space.
The LP3986's performance is optimized for battery
powered systems to deliver ultra low noise, extremely
low dropout voltage and low quiescent current
independent of load current. Regulator ground current
increases very slightly in dropout, further prolonging
the battery life. Optional external bypass capacitor
reduces the output noise further without slowing down
the load transient response. Fast start-up time is
achieved by utilizing a speed-up circuit that actively
pre-charges the bypass capacitor. Power supply
rejection is better than 60 dB at low frequencies and
55 dB at 10 kHz. High power supply rejection is
maintained at low input voltage levels common to
battery operated circuits.
The LP3986 is available in a DSBGA package.
Performance is specified for a −40°C to +125°C
temperature range. For single LDO applications,
please refer to the LP3985 datasheet.
Table 1. Key Specifications
Guaranteed output current per regulator
VALUE
UNIT
150
mA
Typical quiescent current when both regulators in shutdown mode
1
nA
Typical dropout voltage at 150 mA output current
60
mV
Typical ground current
115
µA
Typical output noise
40
µV
Fast turn-on circuit
Junction temperature
200
µs
−40 to +125
°C
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2001–2013, Texas Instruments Incorporated
LP3986
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
www.ti.com
Typical Application Circuit
Input
2.7V to 6.0V
VOUT1
VIN
CIN
LP3986
EN1
VOUT2
EN2
1PF
1PF
BYPASS
CBYPASS*
GND
0.01PF
Block Diagram
LP3986
VOUT2
VIN
VOUT1
BYPASS
Fast Turn
On
circuit
Vreference
1.23V
VEN2
VEN1
Over Current &
Thermal
Protection
GND
Pin Functions
PIN DESCRIPTIONS
(1)
2
Name
DSBGA (1)
VOUT2
A1
Output Voltage of the second LDO
EN2
B1
Enable input for the second LDO
BYPASS
C1
Bypass capacitor for the bandgap
GND
C2
Common ground
GND
C3
Common ground
EN1
B3
Enable input for the first LDO
VOUT1
A3
Output Voltage of the first LDO
VIN
A2
Common input for both LDOs
Function
The pin numbering scheme for the DSBGA package was revised in April 2002 to conform to JEDEC standard. Only the pin numbers
were revised. No changes to the physical location of the inputs/outputs were made. For reference purposes, the obsolete numbering
scheme had VOUT2 as pin 1, EN2 as pin 2, BYPASS as pin 3, GND as pins 4 and 5, EN1 as pin 6, VOUT1 as pin 7, and VIN as pin 8.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
LP3986
www.ti.com
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
Connection Diagram
8 Bump DSBGA Package – Top View
See Package Number YZR0008
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1) (2) (3)
−0.3 to 6.5V
VIN, VEN
−0.3 to (VIN+0.3V) ≤ 6.5V
VOUT
Junction Temperature
150°C
Storage Temperature
−65°C to +150°C
Pad Temp.
(4)
Maximum Power Dissipation
235°C
(5)
364mW
ESD Rating (6)
Human Body Model
Machine Model
(1)
(2)
(3)
(4)
(5)
(6)
2kV
200V
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits
and associated test conditions, see Electrical Characteristics.
All voltages are with respect to the potential at the GND pin.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office / Distributors for
availability and specifications.
Additional information on pad temperature can be found in TI's AN-1112 application report (SNVA009).
The Absolute Maximum power dissipation depends on the ambient temperature and can be calculated using the formula: PD = (TJ TA)/θJA,Where TJ is the junction temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance. The
364mW rating appearing under Absolute Maximum Ratings results from substituting the Absolute Maximum junction temperature,
150°C, for TJ, 70°C for TA, and 220°C/W for θJA. More power can be dissipated safely at ambient temperatures below 70°C . Less
power can be dissipated safely at ambient temperatures above 70°C. The Absolute Maximum power dissipation can be increased by
4.5mW for each degree below 70°C, and it must be derated by 4.5mW for each degree above 70°C.
The human body model is 100pF discharged through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor
discharged directly into each pin.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
3
LP3986
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
Operating Ratings
www.ti.com
(1) (2)
VIN
2.7 to 6V
VEN
0 to (VIN+ 0.3V) ≤ 6V
−40°C to +125°C
Junction Temperature
Thermal Resistance
θJA
220°C/W
Maximum Power Dissipation
(1)
(2)
(3)
(3)
250mW
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits
and associated test conditions, see Electrical Characteristics.
All voltages are with respect to the potential at the GND pin.
Like the Absolute Maximum power dissipation, the maximum power dissipation for operation depends on the ambient temperature. The
250mW rating appearing under Operating Ratings results from substituting the maximum junction temperature for operation, 125°C, for
TJ, 70°C for TA, and 220°C/W for θJA into (1) above. More power can be dissipated at ambient temperatures below 70°C . Less power
can be dissipated at ambient temperatures above 70°C. The maximum power dissipation for operation can be increased by 4.5mW for
each degree below 70°C, and it must be derated by 4.5mW for each degree above 70°C.
Electrical Characteristics
Unless otherwise specified: VIN = VOUT(nom) + 0.5V, CIN = 1 µF, IOUT = 1mA, COUT = 1 µF, CBYPASS = 0.01µF. Typical values and
limits appearing in standard typeface are for TJ = 25°C. Limits appearing in boldface type apply over the entire junction
temperature range for operation, −40°C to +125°C. (1) (2)
Symbol
ΔVOUT
Parameter
Conditions
% of
VOUT(nom)
0.092
0.128
%/V
IOUT = 1mA to 150 mA
0.003
0.006
0.01
%/mA
(4)
Quiescent Current
VIN = VOUT(nom) + 1V,
IOUT = 150 mA (Figure 1)
1.5
VIN = 3.1V,
f = 1 kHz,
IOUT = 50 mA (Figure 2)
60
VIN = 3.1V,
f = 10 kHz,
IOUT = 50 mA (Figure 2)
50
Both Regulators ON
VEN = 1.4V, IOUT = 0 mA
115
200
Both Regulators ON
VEN = 1.4V, IOUT = 0 to 150 mA
220
320
One Regulator ON
VEN = 1.4V IOUT = 0 mA
75
130
One Regulator ON
VEN = 1.4V IOUT = 0 to 150 mA
130
200
0.001
2
4
2
100
VEN = 0.4V, Both Regulators OFF
(shutdown)
4
2.5
3.0
0.006
IQ
(5)
−2.5
−3.0
VIN = (VOUT(nom) + 0.5V) to 6.0V,
IOUT = 1 mA
Power Supply Rejection Ratio
(4)
Max
Line Regulation Error (3)
PSRR
(2)
(3)
Units
Min
IOUT = 1mA
Output AC Line Regulation
(1)
Limit
Output Voltage
Tolerance
Load Regulation Error
ISC
Typ
Dropout Voltage (5)
IOUT = 1 mA
IOUT = 150 mA
0.4
60
Short Circuit Current Limit
Output Grounded
600
mVP-P
dB
µA
mV
mA
All limits are guaranteed. All electrical characteristics having room temperature limits are tested during production with TJ = 25°C or
correlated using Statistical Quality Control (SQC) methods. All hot and cold limits are guaranteed by correlating the electrical
characteristics to process and temperature variations and applying statistical process control.
The target output voltage, which is labeled VOUT(nom), is the desired voltage option.
The output voltage changes slightly with line voltage. An increase in the line voltage results in a slight increase in the output voltage and
vice versa.
The output voltage changes slightly with load current. An increase in the load current results in a slight decrease in the output voltage
and vice versa. Tested limit applies to Vout 's of 2.5V and greater.
Dropout voltage is the input-to-output voltage difference at which the output voltage is 100mV below its nominal value.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
LP3986
www.ti.com
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
Electrical Characteristics (continued)
Unless otherwise specified: VIN = VOUT(nom) + 0.5V, CIN = 1 µF, IOUT = 1mA, COUT = 1 µF, CBYPASS = 0.01µF. Typical values and
limits appearing in standard typeface are for TJ = 25°C. Limits appearing in boldface type apply over the entire junction
temperature range for operation, −40°C to +125°C. (1) (2)
Symbol
IOUT(PK)
Parameter
Peak Output Current (6)
(7)
Conditions
Typ
VOUT ≥ VOUT(nom) - 5%
500
Limit
Min
Max
Units
300
mA
TON
Turn-On Time
CBYPASS = 0.01 µF
200
µs
en
Output Noise Voltage
BW = 10 Hz to 100 kHz,
COUT = 1µF
40
µVrms
ρn(1/f)
Output Noise Density
f = 120 Hz,
COUT = 1µF
1
µV/√Hz
IEN
Maximum Input Current at EN
VEN = 0.4 and VIN = 6V
VIL
Maximum Low Level Input
Voltage at EN
VIN = 2.7 to 6V
VIH
Minimum High Level Input
Voltage at EN
VIN = 2.7 to 6V
Xtalk
Crosstalk Rejection
−60
−60
Input capacitance (8)
If VOUT = 1.8V,
VIN_MIN>= 2.9V
COUT
Capacitance (8)
All VOUT > = 2.5V,
If VOUT = 1.8V,
VIN_MIN>= 2.9V
(6)
(7)
(8)
(9)
See
(9)
V
1.4
ΔILoad2 = 150 mA at 1KHz rate
ΔILoad1 = 1 mA
ΔVOUT2/ΔVOUT1
CIN
nA
0.4
ΔILoad1 = 150 mA at 1KHz rate
ΔILoad2 = 1 mA
ΔVOUT2/ΔVOUT1
All VOUT > = 2.5V,
ESR
±10
V
dB
1
µF
4.7
µF
1
22
µF
2.2
22
µF
5
500
mΩ
IPEAK guaranteed for Vout 's of 2.5V and greater.
Turn-on time is that between the enable input just exceeding VIH and the output voltage just reaching 95% of its nominal value.
Range of capacitor values for which the device will remain stable. This electrical specification is guaranteed by design.
Range of capacitor ESR values for which the device will remain stable. This electrical specification is guaranteed by design.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
5
LP3986
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
www.ti.com
TEST SIGNALS
Figure 1. Line Regulation Input Test Signal
Figure 2. PSRR Input Test Signal
6
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
LP3986
www.ti.com
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise specified, CIN= COUT 1µF Ceramic, C BP= 0.01µ F, VIN = VOUT + 0.5, TA= 25°C, both enable pins are tied to
VIN
Power Supply Rejection Ratio (CBP = 0.001µF)
Power Supply Rejection Ratio (CBP = 0.01µF)
Figure 3.
Figure 4.
Power Supply Rejection Ratio (CBP = 0.1µF)
Output Noise Spectral Density
Figure 5.
Figure 6.
Line Transient Response (CBP = 0.001µF)
Line Transient Response (CBP = 0.01µF)
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
7
LP3986
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, CIN= COUT 1µF Ceramic, C BP= 0.01µ F, VIN = VOUT + 0.5, TA= 25°C, both enable pins are tied to
VIN
8
Load Transient & Cross Talk (VIN = VOUT + 0.2V)
Load Transient & Cross Talk (VIN = VOUT + 0.2V)
Figure 9.
Figure 10.
Start-Up Time (CBP = 0.001, 0.01, 0.1µF)
Enable Response ( VIN = 4.2V )
Figure 11.
Figure 12.
Enable Response (VIN = VOUT+ 0.2V)
Enable Response
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
LP3986
www.ti.com
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, CIN= COUT 1µF Ceramic, C BP= 0.01µ F, VIN = VOUT + 0.5, TA= 25°C, both enable pins are tied to
VIN
Output Short Circuit Current at VIN = 6V
Output Short Circuit Current at VIN = 3.3V
Figure 15.
Figure 16.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
9
LP3986
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
www.ti.com
APPLICATION HINTS
EXTERNAL CAPACITORS
Like any low-dropout regulator, the LP3986 requires external capacitors for regulator stability. The LP3986 is
specifically designed for portable applications requiring minimum board space and smallest components. These
capacitors must be correctly selected for good performance.
INPUT CAPACITOR
An input capacitance of ≊ 1µF is required between the LP3986 input pin and ground (the amount of the
capacitance may be increased without limit).
This capacitor must be located a distance of not more than 1cm from the input pin and returned to a clean
analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input.
Important: Tantalum capacitors can suffer catastrophic failures due to surge current when connected to a lowimpedance source of power (like a battery or a very large capacitor). If a tantalum capacitor is used at the input,
it must be guaranteed by the manufacturer to have a surge current rating sufficient for the application.
There are no requirements for the ESR on the input capacitor, but tolerance and temperature coefficient must be
considered when selecting the capacitor to ensure the capacitance will be ≊ 1µF over the entire operating
temperature range.
OUTPUT CAPACITOR
The LP3986 is designed specifically to work with very small ceramic output capacitors, any ceramic capacitor
(temperature characteristics X7R, X5R, Z5U or Y5V) in 1 to 22 µF range with 5mΩ to 500mΩ ESR range is
suitable in the LP3986 application circuit.
It may also be possible to use tantalum or film capacitors at the output, but these are not as attractive for
reasons of size and cost (see next section Capacitor Characteristics).
The output capacitor must meet the requirement for minimum amount of capacitance and also have an ESR
(Equivalent Series Resistance) value which is within a stable range.
NO-LOAD STABILITY
The LP3986 will remain stable and in regulation with no-load (other than the internal voltage divider). This is
specially important in CMOS RAM keep-alive applications.
CAPACITOR CHARACTERISTICS
The LP3986 is designed to work with ceramic capacitors on the output to take advantage of the benefits they
offer: for capacitance values in the range of 1µF to 4.7µF range, ceramic capacitors are the smallest, least
expensive and have the lowest ESR values (which makes them best for eliminating high frequency noise). The
ESR of a typical 1µF ceramic capacitor is in the range of 20 mΩ to 40 mΩ, which easily meets the ESR
requirement for stability by the LP3986.
The ceramic capacitor's capacitance can vary with temperature. The capacitor type X7R, which operates over a
temperature range of -55°C to +125°C, will only vary the capacitance to within ±15%. Most large value ceramic
capacitors (≊ 2.2µF) are manufactured with Z5U or Y5V temperature characteristics. Their capacitance can drop
by more than 50% as the temperature goes from 25°C to 85°C. Therefore, X7R is recommended over Z5U and
Y5 in applications where the ambient temperature will change significantly above or below 25°C.
Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more
expensive when comparing equivalent capacitance and voltage ratings in the 1µF to 4.7µF range.
Another important consideration is that tantalum capacitors have higher ESR values than equivalent size
ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the
stable range, it would have to be larger in capacitance (which means bigger and more costly ) than a ceramic
capacitor with the same ESR value. It should also be noted that the ESR of a typical tantalum will increase about
2:1 as the temperature goes from 25°C down to −40°C, so some guard band must be allowed.
10
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
LP3986
www.ti.com
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
NOISE BYPASS CAPACITOR
Connecting a 0.01µF capacitor between the CBYPASS pin and ground significantly reduces noise on the regulator
output. This cap is connected directly to a high impedance node in the band gap reference circuit. Any significant
loading on this node will cause a change on the regulated output voltage. For this reason, DC leakage current
through this pin must be kept as low as possible for best output voltage accuracy. The use of this 0.01µF bypass
capacitor is strongly recommended to prevent overshoot on the output during start up.
The types of capacitors best suited for the noise bypass capacitor are ceramic and film. High-quality ceramic
capacitors with either NPO or COG dielectric typically have very low leakage. Polypropolene and polycarbonate
film capacitors are available in small surface-mount packages and typically have extremely low leakage current.
Unlike many other LDOs, addition of a noise reduction capacitor does not effect the transient response of the
device.
ON/OFF INPUT OPERATION
The LP3986 is turned off by pulling the VEN pin low, and turned on by pulling it high. If this feature is not used,
the VEN pin should be tied to VIN to keep the regulator output on at all times. To assure proper operation, the
signal source used to drive the VEN input must be able to swing above and below the specified turn-on/off voltage
thresholds listed in the Electrical Characteristics section under VIL and VIH.
FAST ON-TIME
The LP3986 outputs are turned on after Vref voltage reaches its final value (1.23V nominal). To speed up this
process, the noise reduction capacitor at the bypass pin is charged with an internal 70µA current source. The
current source is turned off when the bandgap voltage reaches approximately 95% of its final value. The turn on
time is determined by the time constant of the bypass capccitor. The smaller the capacitor value, the shorter the
turn on time, but less noise gets reduced. As a result, turn on time and noise reduction need to be taken into
design consideration when choosing the value of the bypass capacitor.
DSBGA MOUNTING
The DSBGA package requires specific mounting techniques which are detailed in TI's AN-1112 application report
(SNVA009), in particular the section Surface Mount Assembly Considerations.
For best results during assembly, alignment ordinals on the PC board may be used to facilitate placement of the
DSBGA device.
DSBGA LIGHT SENSITIVITY
Exposing the DSBGA device to direct sunlight will cause misoperation of the device. Light sources such as
halogen lamps can effect electrical performance if brought near to the device.
The wavelengths which have most detrimental effect are reds and infra-reds, which means that the fluorescent
lighting used inside most buildings has very little effect on performance. A DSBGA test board was brought to
within 1cm of a fluorescent desk lamp and the effect on the regulated output voltage was negligible, showing a
deviation of less than 0.1% from nominal.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
11
LP3986
SNVS142U – AUGUST 2001 – REVISED FEBRUARY 2013
www.ti.com
REVISION HISTORY
Changes from Revision T (February 2013) to Revision U
•
12
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 11
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3986
PACKAGE OPTION ADDENDUM
www.ti.com
11-Sep-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP3986TL-2518/NOPB
ACTIVE
DSBGA
YZR
8
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
D
30
LP3986TL-2525/NOPB
ACTIVE
DSBGA
YZR
8
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
D
27
LP3986TL-2828/NOPB
ACTIVE
DSBGA
YZR
8
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
D
10
LP3986TL-285285/NOPB
ACTIVE
DSBGA
YZR
8
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
D
11
LP3986TL-3030/NOPB
ACTIVE
DSBGA
YZR
8
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
D
12
LP3986TLX-2828/NOPB
ACTIVE
DSBGA
YZR
8
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
D
10
LP3986TLX285285/NOPB
ACTIVE
DSBGA
YZR
8
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
D
11
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Sep-2016
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Aug-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LP3986TL-2518/NOPB
DSBGA
YZR
8
250
178.0
8.4
LP3986TL-2525/NOPB
DSBGA
YZR
8
250
178.0
LP3986TL-2828/NOPB
DSBGA
YZR
8
250
178.0
LP3986TL-285285/NOPB DSBGA
YZR
8
250
W
Pin1
(mm) Quadrant
1.7
1.7
0.76
4.0
8.0
Q1
8.4
1.7
1.7
0.76
4.0
8.0
Q1
8.4
1.7
1.7
0.76
4.0
8.0
Q1
178.0
8.4
1.7
1.7
0.76
4.0
8.0
Q1
LP3986TL-3030/NOPB
DSBGA
YZR
8
250
178.0
8.4
1.7
1.7
0.76
4.0
8.0
Q1
LP3986TLX-2828/NOPB
DSBGA
YZR
8
3000
178.0
8.4
1.7
1.7
0.76
4.0
8.0
Q1
LP3986TLX285285/NOPB DSBGA
YZR
8
3000
178.0
8.4
1.7
1.7
0.76
4.0
8.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Aug-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP3986TL-2518/NOPB
DSBGA
YZR
8
250
210.0
185.0
35.0
LP3986TL-2525/NOPB
DSBGA
YZR
8
250
210.0
185.0
35.0
LP3986TL-2828/NOPB
DSBGA
YZR
8
250
210.0
185.0
35.0
LP3986TL-285285/NOPB
DSBGA
YZR
8
250
210.0
185.0
35.0
LP3986TL-3030/NOPB
DSBGA
YZR
8
250
210.0
185.0
35.0
LP3986TLX-2828/NOPB
DSBGA
YZR
8
3000
210.0
185.0
35.0
LP3986TLX285285/NOPB
DSBGA
YZR
8
3000
210.0
185.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
YZR0008xxx
D
0.600±0.075
E
TLA08XXX (Rev C)
D: Max = 1.591 mm, Min = 1.53 mm
E: Max = 1.591 mm, Min = 1.53 mm
4215045/A
NOTES:
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
www.ti.com
12/12
IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated