MAX4596DCKR

     W      www.ti.com SLLS641 – JANUARY 2005 Description The MAX4596 is a single-pole single-throw (SPST) analog switch that is designed to operate from 2 V to 5 V. This device can handle both digital and analog signals, and signals up to V+ (peak) can be transmitted in either direction. Applications D Sample-and-Hold Circuits Features D Low ON-State Resistance (10 W) D ON-State Resistance Flatness (1.5 W) D Control Inputs Are 5.5-V Tolerant D Low Charge Injection (5 pC Max) D 300-MHz −3-dB Bandwidth at 255C D Low Total Harmonic Distortion (THD) (0.05%) D 2-V to 5.5-V Single-Supply Operation D Specified at 5-V and 3.3-V Nodes D −83-dB OFF Isolation at 1 MHz D Latch-Up Performance Exceeds 100 mA Per D D D Battery-Powered Equipment D Audio and Video Signal Routing D Communication Circuits D JESD 78, Class II 0.5-nA Max OFF Leakage ESD Performance Tested Per JESD 22 − 2000-V Human-Body Model (A114-B, Class II) − 1000-V Charged-Device Model (C101) TTL/CMOS-Logic Compatible Summary of Characteristics V+ = 5 V, TA = 25°C SOT-23 OR SC-70 PACKAGE (TOP VIEW) IN 1 5 Single Pole Single Throw (SPST) Configuration V+ Number of channels COM 2 4 GND 3 NO 1 ON-state resistance (ron) 10 Ω ON-state resistance flatness (ron(flat)) 1.5 Ω Turn-on/turn-off time (tON/tOFF) 35 ns/40 ns Charge injection (QC) 5 pC Bandwidth (BW) OFF isolation (OISO) FUNCTION TABLE NO TO COM, COM TO NO IN 300 MHz −83 dB at 1 MHz Total harmonic distortion (THD) 0.05% ±0.05 nA Leakage current(ICOM(OFF)/INO(OFF)) L OFF Power-supply current (I+) H ON Package option 1 µA 5-pin SOT-23 or SC-70 ORDERING INFORMATION TA −40°C to 85°C PACKAGE(1) ORDERABLE PART NUMBER TOP-SIDE MARKING(2) SOT (SOT-23) − DBV Tape and reel MAX4596DBVR 6SB_ SOT (SC−70) − DCK Tape and reel MAX4596DCKR SB_ (1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. (2) DBV/DCK: The actual top-side marking has one additional character that designates the assembly/test site. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.    !" # $%&" !#  '%()$!" *!"&+ *%$"# $ " #'&$$!"# '& ",& "&#  &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0  !)) '!!&"&#+ Copyright  2005, Texas Instruments Incorporated 
     W      www.ti.com SLLS641 – JANUARY 2005 Pin Configurations Available in Other Pin Configurations IN 1 5 V+ 4 NO COM 1 NO 2 GND 3 COM 2 5 V+ 4 IN MAX4594 GND 3 COM MAX4596 1 NC 2 GND 3 5 V+ IN 1 5 V+ 4 NC COM 2 4 IN MAX4595 GND 3 MAX4597 Absolute Minimum and Maximum Ratings(1)(2) over operating free-air temperature range (unless otherwise noted) V+ VNO VCOM IK INO ICOM INO ICOM MIN MAX Supply voltage range(3) −0.3 6 UNIT V Analog voltage range(3)(4) −0.3 V+ + 0.3 V Analog port diode current VNO, VCOM < 0 −50 On-state switch current VNO, VCOM = 0 to V+ −20 20 mA On-state switch current (pulsed at 1 ms, 10% duty cycle) VNO, VCOM = 0 to V+ −40 40 mA −0.3 6 V VI IIK Digital input voltage range(3)(4) I+ IGND Continuous current through V+ θJA Package thermal impedance(5) Digital input clamp current VI < 0 mA −50 mA 100 Continuous current through GND −100 mA mA DBV package 206 DCK package 252 °C/W Tstg Storage temperature range −65 150 °C (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum (3) All voltages are with respect to ground, unless otherwise specified. (4) The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed. (5) The package thermal impedance is calculated in accordance with JESD 51-7. 2 
     W      www.ti.com SLLS641 – JANUARY 2005 Electrical Characteristics for 5-V Supply(1) V+ = 4.5 V to 5.5 V, TA = −40°C to 85°C (unless otherwise noted) PARAMETER TEST CONDITIONS SYMBOL TA V+ MIN TYP MAX UNIT Analog Switch Analog signal range VCOM, VNO ON-state resistance ron ON-state resistance flatness ron(flat) 0 VNO = 3.5 V ICOM = 10 mA, Switch ON, See Figure 13 25°C VNO = 1.5 V, 2.5 V, 3.5 V ICOM = 10 mA, Switch ON, See Figure 13 25°C Full VNO = 1 V, VCOM = 4.5 V, or VNO = 4.5 V, VCOM = 1 V, Switch OFF, See Figure 14 25°C COM OFF leakage current VCOM = 1 V, VNO = 4.5 V, or VCOM = 4.5 V, VNO = 1 V, Switch OFF, See Figure 14 25°C ICOM(OFF) INO(ON) VNO = 1 V, VCOM = 1 V, or VNO = 4.5 V, VCOM = 4.5 V, or VNO = 1 V, 4.5 V, VCOM = Open, Switch ON, See Figure 15 VCOM = 1 V, VNO = 1 V, or VCOM = 4.5 V, VNO = 4.5 V, or VCOM = 1 V, 4.5 V, VNO = Open, Switch ON, See Figure 15 ICOM(ON) 10 12 0.5 −0.5 0.01 −0.5 5 0.01 0.5 5.5 V nA −5 25°C Ω nA −5 Full Ω 0.5 5.5 V Full V 1.5 2 Full INO(OFF) COM ON leakage current 6.5 4.5 V 4.5 V NO OFF leakage current NO ON leakage current V+ −1 5 0.01 1 5.5 V nA Full −10 25°C −1 10 0.01 1 5.5 V nA Full −10 10 Full 2.4 5.5 V Full 0 0.8 V 25°C −1 Digital Control Input (IN) Input logic high Input logic low Input leakage current VIH VIL IIH, IIL VI = V+ or 0 Full 5.5 V −1 0.03 1 1 µA A (1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum 3 
     W      www.ti.com SLLS641 – JANUARY 2005 Electrical Characteristics for 5-V Supply(1) (continued) V+ = 4.5 V to 5.5 V, TA = −40°C to 85°C (unless otherwise noted) PARAMETER TEST CONDITIONS SYMBOL TA V+ MIN TYP MAX 20 35 UNIT Dynamic Turn-on time VNO = 3 V, RL = 300 Ω, CL = 35 pF, See Figure 17 25°C 5V tON Full 4.5 V to 5.5 V Turn-off time VCOM = 3 V, RL = 300 Ω, CL = 35 pF, See Figure 17 25°C 5V tOFF Full 4.5 V to 5.5 V VGEN = 0, RGEN = 0, CL = 1 nF, See Figure 20 25°C 5V 2 45 25 ns 40 50 ns Charge injection QC NO OFF capacitance CNO(OFF) VNO = V+ or GND, f = 1 MHz, Switch OFF, See Figure 16 25°C 5V 8 pF COM OFF capacitance CCOM(OFF) VCOM = V+ or GND, f = 1 MHz, Switch OFF, See Figure 16 25°C 5V 8 pF NO ON capacitance CNO(ON)) VNO = V+ or GND, f = 1 MHz, Switch ON, See Figure 16 25°C 5V 20 pF COM ON capacitance CCOM(ON) VCOM = V+ or GND, f = 1 MHz, Switch ON, See Figure 16 25°C 5V 20 pF CI VI = V+ or GND, See Figure 16 25°C 5V 3 pF BW RL = 50 Ω, Signal = 0 dBm, Switch ON, See Figure 18 25°C 5V 300 MHz Digital input capacitance Bandwidth 5 pC OFF isolation OISO RL = 50 Ω, CL = 5 pF, VNO = 1 VRMS, f = 1 MHz, Switch OFF, See Figure 19 25°C 5V −83 dB Total harmonic distortion THD RL = 600 Ω, CL = 50 pF, VSOURCE = 5 Vp-p, f = 20 Hz to 20 kHz, See Figure 21 25°C 5V 0.05 % Supply Positive supply I+ VI = V+ or GND, Switch ON or OFF Full 5.5 V current (1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum 4 1 µA 
     W      www.ti.com SLLS641 – JANUARY 2005 Electrical Characteristics for 3-V Supply(1) V+ = 2.7 V to 3.6 V, TA = −40°C to 85°C (unless otherwise noted) PARAMETER TEST CONDITIONS SYMBOL TA V+ MIN TYP MAX UNIT Analog Switch Analog signal range ON-state resistance VCOM, VNO ron 0 VNO = 1.5 V, ICOM = 10 mA, Switch ON, See Figure 13 25°C Full V+ 10 2.7 V 20 25 V Ω Digital Control Input (IN) Input logic high Input logic low VIH VIL Full 2 5.5 V Full 0 0.8 V Input leakage current IIH, IIL VI = V+ or 0 Turn-on time VNO = 2 V, RL = 300 Ω, CL = 35 pF, See Figure 17 25°C 3V tON Full 2.7 V to 3.6 V Turn-off time VNO = 2 V, RL = 300 Ω, CL = 35 pF, See Figure 17 25°C 3V tOFF Full 2.7 V to 3.6 V VGEN = 0, RGEN = 0, CL = 1 nF, See Figure 20 25°C 3V 25°C Full −1 3.6 V 0.03 −1 1 1 µA A Dynamic Charge injection QC 25 45 55 30 50 60 2 ns ns 4 pC 1 µA Supply Positive supply I+ VI = V+ or GND, Switch ON or OFF Full 3.6 V current (1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum 5 
     W      www.ti.com SLLS641 – JANUARY 2005 TYPICAL PERFORMANCE 10 8 TA = 25_C 8 6 855C 255C 6 ron (W) ron (Ω) V+ = 3 V 4 4 –405C V+ = 5 V 2 2 0 0 0 1 2 3 4 5 0 1 2 VCOM (V) 1.0 ICOM(ON)/INO(ON) –405C 0.8 Leakage Current (nA) 8 ron (W) 5 Figure 2. ron vs VCOM (V+ = 5 V) 10 6 4 255C 855C 2 0.6 INO(OFF)/ICOM(OFF) 0.4 0.2 0.0 0 0 1 2 3 VCOM (V) −40°C 2.0 20 1.5 18 tOFF 16 tON/tOFF (ns) 0.5 V+ = 3 V 85°C tON 1.0 0.0 25°C TA (°C) Figure 4. Leakage Current vs Temperature (V+ = 5 V) Figure 3. ron vs VCOM (V+ = 3 V) Charge Injection (pC) 4 VCOM (V) Figure 1. ron vs VCOM V+ = 5 V −0.5 −1.0 −1.5 −2.0 14 12 10 8 −2.5 6 −3.0 0 1 2 3 4 Bias Voltage (V) Figure 5. Charge-Injection (QC) vs VCOM 6 3 5 0 1 2 3 V+ (V) 4 5 6 Figure 6. tON and tOFF vs Supply Voltage 
     W      www.ti.com SLLS641 – JANUARY 2005 TYPICAL PERFORMANCE 12 Logic Level Threshold (nA) 3 tON/tOFF (ns) 11 10 9 tON 8 7 tOFF 6 −40°C 25°C VIH 2 1 VIL 0 0 85°C 1 2 TA (5C) Figure 7. tON and tOFF vs Temperature (V+ = 5 V) 3 V+ (V) 4 5 6 Figure 8. Logic-Level Threshold vs V+ 0.0 0 −0.5 −20 Attenuation (dB) Gain (dB) −1.0 −1.5 −2.0 −2.5 −3.0 −40 −60 −80 −100 −3.5 −4.0 0.1 1 10 Frequency (MHz) 100 −120 0.1 1000 Figure 9. Bandwidth (Gain vs Frequency) (V+ = 5 V) 1 10 Frequency (MHz) 100 1000 Figure 10. Off Isolation vs Frequency 10 0.20 V+ = 5 V 9 8 0.15 7 5 V+ = 3 V 4 3 2 THD (%) I+ (µA) 6 0.10 V+ = 3 V 0.05 V+ = 5 V 1 0 −40°C 25°C 85°C TA (5C) Figure 11. Power-Supply Current vs Temperature 0.00 0.1 1 10 100 1000 Frequency (MHz) Figure 12. Total Harmonic Distortion vs Frequency 7 
     W      www.ti.com SLLS641 – JANUARY 2005 PIN DESCRIPTION PIN NUMBER NAME DESCRIPTION 1 IN 2 COM Digital control pin to connect COM to NO Common 3 GND Digital ground 4 NO Normally open 5 V+ Power supply PARAMETER DESCRIPTION SYMBOL 8 DESCRIPTION VCOM Voltage at COM VNO Voltage at NO ron Resistance between COM and NO ports when the channel is ON ron(flat) Difference between the maximum and minimum value of ron in a channel over the specified range of conditions INO(OFF) Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the OFF state INO(ON) Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the ON state and the output (COM) open ICOM(OFF) Leakage current measured at the COM port, with the corresponding channel (COM to NO) in the OFF state ICOM(ON) Leakage current measured at the COM port, with the corresponding channel (COM to NO) in the ON state and the output (NO) open VIH Minimum input voltage for logic high for the control input (IN) VIL Maximum input voltage for logic low for the control input (IN) VI Voltage at the control input (IN) IIH, IIL Leakage current measured at the control input (IN) tON Turn-on time for the switch. This parameter is measured under the specified range of conditions and by the propagation delay between the digital control (IN) signal and analog output (COM or NO) signal when the switch is turning ON. tOFF Turn-off time for the switch. This parameter is measured under the specified range of conditions and by the propagation delay between the digital control (IN) signal and analog output (COM or NO) signal when the switch is turning OFF. QC Charge injection is a measurement of unwanted signal coupling from the control (IN) input to the analog (NO or COM) output. This is measured in coulomb (C) and measured by the total charge induced due to switching of the control input. Charge injection, QC = CL × ∆VCOM, CL is the load capacitance, and ∆VCOM is the change in analog output voltage. CNO(OFF) CNO(ON) Capacitance at the NO port when the corresponding channel (NO to COM) is OFF CCOM(OFF) CCOM(ON) Capacitance at the COM port when the corresponding channel (COM to NO) is OFF CI Capacitance of control input (IN) OISO OFF isolation of the switch is a measurement of OFF-state switch impedance. This is measured in dB in a specific frequency, with the corresponding channel (NO to COM) in the OFF state. BW Bandwidth of the switch. This is the frequency in which the gain of an ON channel is −3 dB below the DC gain. THD Total harmonic distortion describes the signal distortion caused by the analog switch. This is defined as the ratio of root mean square (RMS) value of the second, third, and higher harmonic to the absolute magnitude of the fundamental harmonic. I+ Static power-supply current with the control (IN) pin at V+ or GND Capacitance at the NO port when the corresponding channel (NO to COM) is ON Capacitance at the COM port when the corresponding channel (COM to NO) is ON 
     W      www.ti.com SLLS641 – JANUARY 2005 PARAMETER MEASUREMENT INFORMATION V+ VNO NO COM VCOM + Channel ON r on + VI ICOM IN VCOM * VNO W I COM VI = VIH or VIL + GND Figure 13. ON-State Resistance (ron) V+ VNO NO COM + VCOM + VI OFF-State Leakage Current Channel OFF VI = VIH or VIL IN + GND Figure 14. OFF-State Leakage Current (ICOM(OFF), INO(OFF)) V+ VNO NO COM + VI VCOM ON-State Leakage Current Channel ON VI = VIH or VIL IN + GND Figure 15. ON-State Leakage Current (ICOM(ON), INO(ON)) 9 
     W      www.ti.com SLLS641 – JANUARY 2005 V+ VNO NO Capacitance Meter VBIAS = V+ or GND VI = VIH or VIL VCOM COM VBIAS Capacitance is measured at NO, COM, and IN inputs during ON and OFF conditions. IN VI GND Figure 16. Capacitance (CI, CCOM(OFF), CCOM(ON), CNO(OFF), CNO(ON)) V+ NO (3) VCOM VI VNO TEST RL CL tON 300 Ω 35 pF tOFF 300 Ω 35 pF COM CL(2) RL IN Logic Input(1) V+ Logic Input (VI) GND 50% 50% 0 tON tOFF Switch Output (VNO) 90% 90% (1) All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns. (2) CL includes probe and jig capacitance. (3) See Electrical Characteristics for VCOM. Figure 17. Turn-On (tON) and Turn-Off Time (tOFF) V+ Network Analyzer 50 W VNO NO Channel ON: NO to COM COM VCOM Source Signal VI = V+ or GND Network Analyzer Setup 50 W VI + IN Source Power = 0 dBm (632-mV P-P at 50-W load) GND Figure 18. Bandwidth (BW) 10 DC Bias = 350 mV 
     W      www.ti.com SLLS641 – JANUARY 2005 V+ Network Analyzer Channel OFF: NO to COM 50 W VNO NO VI = V+ or GND VCOM COM Source Signal 50 W Network Analyzer Setup VI 50 W Source Voltage = 1 VRMS IN + DC Bias = 350 mV GND Figure 19. OFF Isolation (OISO) V+ RGEN VGEN Logic Input (VI) VIH OFF ON OFF V IL NO COM + VCOM ∆VCOM VCOM CL(1) VI VGEN = 0 to V+ RGEN = 0 CL = 1 nF QC = CL × ∆VCOM VI = VIH or VIL IN Logic Input(2) GND (1) CL includes probe and jig capacitance. (2) All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns. Figure 20. Charge Injection (QC) VI = V+/2 or −V+/2 RL = 600 Ω fSOURCE = 20 Hz to 20 kHz CL = 50 pF Channel ON: COM to NO VSOURCE = V+ P-P V+/2 Audio Analyzer NO Source Signal COM CL(1) 600 W VI 600 W IN GND −V+/2 (1) CL includes probe and jig capacitance. Figure 21. Total Harmonic Distortion (THD) 11 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) MAX4596DBVR ACTIVE SOT-23 DBV 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 6SCR Samples MAX4596DCKR ACTIVE SC70 DCK 5 3000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 SCR Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of