MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5259,
MSP430F5255, MSP430F5258,
MSP430F5254, MSP430F5257,
MSP430F5253, MSP430F5256
MSP430F5252
MSP430F5255, MSP430F5254,
MSP430F5252
SLAS903D – MSP430F5253,
MAY 2013 – REVISED
OCTOBER 2020
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
MSP430F525x Mixed-Signal Microcontrollers
•
1 Features
•
•
•
•
•
Dual-supply voltage device
– Primary supply (AVCC, DVCC)
• Powered from external supply:
3.6 V down to 1.8 V
• Up to 18 general-purpose I/Os with up to 8
external interrupts
– Low-voltage interface supply (DVIO)
• Powered from separate external supply:
1.62 V to 1.98 V
• Up to 35 general-purpose I/Os with up to 16
external interrupts
• Serial communications
Ultra-low power consumption
– Active mode (AM):
All system clocks active
290 µA/MHz at 8 MHz, 3.0 V, flash program
execution (typical)
150 µA/MHz at 8 MHz, 3.0 V, RAM program
execution (typical)
– Standby mode (LPM3):
Real-time clock (RTC) with crystal, watchdog,
and supply supervisor operational, full RAM
retention, fast wakeup:
2.1 µA at 2.2 V, 2.3 µA at 3.0 V (typical)
Low-power oscillator (VLO), general-purpose
counter, watchdog, and supply supervisor
operational, full RAM retention, fast wakeup:
1.6 µA at 3.0 V (typical)
– Off mode (LPM4):
Full RAM retention, supply supervisor
operational, fast wakeup:
1.3 µA at 3.0 V (typical)
– Shutdown mode (LPM4.5):
0.18 µA at 3.0 V (typical)
Wake up from standby mode in 3.5 µs (typical)
16-bit RISC architecture, extended memory, up to
25-MHz system clock
Flexible power-management system
– Fully integrated LDO with programmable
regulated core supply voltage
– Supply voltage supervision, monitoring, and
brownout
•
•
•
•
•
•
•
•
•
•
•
•
Unified clock system
– FLL control loop for frequency stabilization
– Low-power low-frequency internal clock source
(VLO)
– Low-frequency trimmed internal reference
source (REFO)
– 32-kHz watch crystals (XT1)
– HF crystals up to 32 MHz (XT2)
16-bit timer TA0, Timer_A with five capture/
compare registers
16-bit timer TA1, Timer_A with three capture/
compare registers
16-bit timer TA2, Timer_A with three capture/
compare registers
16-bit timer TB0, Timer_B with seven capture/
compare shadow registers
Four universal serial communication interfaces
– USCI_A0, A1, A2, A3 each support:
• Enhanced UART with automatic baud-rate
detection
• IrDA encoder and decoder
• Synchronous SPI
– USCI_B0, B1, B2, B3 each support:
• I2C
• Synchronous SPI
10-bit analog-to-digital converter (ADC) with
internal reference, sample-and-hold
comparator
Hardware multiplier supports 32-bit operations
Serial onboard programming, no external
programming voltage needed
3-channel internal DMA
Basic timer with RTC feature
Device Comparison Summarizes the available
family members and packages
2 Applications
•
•
•
•
•
•
"Always-on" system controllers
Power-management hubs
Bluetooth® controllers
Analog and digital sensor fusion systems
Data loggers
General-purpose applications
3 Description
Using an "always-on" ultra-low-power system controller can significantly reduce power consumption on portable
devices like handsets and tablets. These controllers can act as sensor hubs and monitor user stimuli (for
example, reading inertial sensors or touch sensors) and vital system parameters like battery health and
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
Submit Document Feedback
Copyright
© 2020 Texas
Instruments
Incorporated
intellectual
property
matters
and other important disclaimers. PRODUCTION DATA.
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
1
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
temperature, while power-hungry application processors and touch screen controllers are turned off. The
microcontroller can then "wake up" the system based on a user input or on a fault condition that requires CPU
intervention.
The MSP430F525x series is the latest addition to the 1.8-V split-rail I/O portfolio (previously only available on
MSP430F522x) and is specifically designed for "always-on" system controller applications. 1.8-V I/O allows for
seamless interface to application processors and other devices without the need for external level translation,
while the primary supply to the MCU can be on a higher voltage rail.
Compared to the MSP430F522x, the MSP430F525x provides up to four times more RAM (32KB) and double the
serial interfaces (four USCI_A and four USCI_B). The MSP430F525x also features four 16-bit timers, a highperformance 10-bit ADC, a hardware multiplier, DMA, a comparator, and an RTC module with alarm capabilities.
The MSP430F525x consumes 290 µA/MHz (typical) in active mode running from flash memory, and it consumes
1.6 µA (typical) in standby mode (LPM3). The MSP430F525x can switch to active mode in 3.5 µs (typical), which
makes it a great fit for "always-on" low-power applications.
Key benefits of the MSP430F525x are as follows:
•
•
•
Up to 32KB of RAM allows complex sensor hub algorithms and high levels of aggregation such as keyboard
control and power management.
Four USCI_A and four USCI_B modules allow for eight concurrent dedicated hardware serial interfaces (for
example, four I2C and four SPI) for fast and robust communication to sensors or peripheral devices.
Up to 35 I/Os that can be used in the 1.8-V voltage rail.
For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User's Guide. For design
guidelines, see Designing With MSP430F522x and MSP430F521x Devices.
Device Information
PART
NUMBER(1)
MSP430F5259IRGC
MSP430F5252IZXH
MSP430F5252IZQE(3)
(1)
(2)
(3)
2
PACKAGE
BODY SIZE(2)
VQFN (64)
9 mm × 9 mm
nFBGA (80)
5 mm × 5 mm
MicroStar Junior™ BGA (80)
5 mm × 5 mm
For the most current part, package, and ordering information for all available devices, see the
Package Option Addendum in Section 11, or see the TI website at www.ti.com.
The sizes shown here are approximations. For the package dimensions with tolerances, see the
Mechanical Data in Section 11.
All orderable part numbers in the ZQE (MicroStar Junior BGA) package have been changed to a
status of Last Time Buy. Visit the Product life cycle page for details on this status.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
4 Functional Block Diagram
Figure 4-1 shows the functional block diagram.
XIN XOUT
XT2IN
XT2OUT
Unified
Clock
System
RSTDVCC RST/NMI BSLEN
ACLK
32KB
16KB
Flash
RAM
SMCLK
MCLK
CPUXV2
and
Working
Registers
128KB
DVCC AVCC
DVSS AVSS
Power
Management
LDO
SVM, SVS
Brownout
PA
DVIO VCORE
P1.x P2.x
SYS
Watchdog
PB
P4.x
P3.x
PC
P6.x
P5.x
PJ
PD
P7.x PJ.x
(1)
(1)(2)
(1)(2)
P4
P5
P7
P3
P6
P2
P1
1×8 I/Os 1×8 I/Os1×5 I/Os1×8 I/Os 1×6 I/Os 1×8 I/Os 1×6 I/Os
PA(1)(2)
1×16 I/Os
PB
1×13 I/Os
Port Map
Control
(P4)
PC
1×14 I/Os
PD
PJ
1×6 I/Os 1×4 I/Os
4x
USCI_Ax:
UART,
IrDA, SPI
I/O Ports
4x
USCI_Bx:
SPI, I2C
MAB
DMA
MDB
3 Channel
EEM
(S: 3+1)
ADC10_A
JTAG,
SBW
Interface
MPY32
I/O are supplied by DVIO
TA0
TA1
TA2
TB0
Timer_A
5 CC
Registers
Timer_A
3 CC
Registers
Timer_A
3 CC
Registers
Timer_B
7 CC
Registers
(1) Interrupt capability
RTC_A
CRC16
(2) Wakeup capability
10 Bit
200 ksps
12 Channels
(10 ext, 2 int)
COMP_B
REF
8 Channels
Copyright © 2016, Texas Instruments Incorporated
Figure 4-1. Functional Block Diagram
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
3
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table of Contents
1 Features............................................................................1
2 Applications..................................................................... 1
3 Description.......................................................................1
4 Functional Block Diagram.............................................. 3
5 Revision History.............................................................. 5
6 Device Comparison......................................................... 7
6.1 Related Products........................................................ 7
7 Terminal Configuration and Functions..........................8
7.1 Pin Diagrams.............................................................. 8
7.2 Signal Descriptions................................................... 10
8 Specifications................................................................ 15
8.1 Absolute Maximum Ratings...................................... 15
8.2 ESD Ratings............................................................. 15
8.3 Recommended Operating Conditions.......................15
8.4 Active Mode Supply Current Into VCC Excluding
External Current.......................................................... 18
8.5 Low-Power Mode Supply Currents (Into VCC)
Excluding External Current..........................................19
8.6 Thermal Resistance Characteristics......................... 20
8.7 Schmitt-Trigger Inputs – General-Purpose I/O
DVCC Domain (P5.0 to P5.5, P6.0 to P6.7, PJ.0
to PJ.3, RSTDVCC).....................................................21
8.8 Schmitt-Trigger Inputs – General-Purpose I/O
DVIO Domain (P1.0 to P1.7, P2.0 to P2.7, P3.0 to
P3.4, P4.0 to P4.7, P7.0 to P7.5, RST/NMI, BSLEN)..21
8.9 Inputs – Interrupts DVCC Domain Port P6 (P6.0
to P6.7)........................................................................21
8.10 Inputs – Interrupts DVIO Domain Ports P1 and
P2 (P1.0 to P1.7, P2.0 to P2.7)................................... 21
8.11 Leakage Current – General-Purpose I/O DVCC
Domain (P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)......22
8.12 Leakage Current – General-Purpose I/O DVIO
Domain (P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4,
P4.0 to P4.7, P7.0 to P7.5)..........................................22
8.13 Outputs – General-Purpose I/O DVCC Domain
(Full Drive Strength) (P5.0 to P5.5, P6.0 to P6.7,
PJ.0 to PJ.3)................................................................22
8.14 Outputs – General-Purpose I/O DVCC Domain
(Reduced Drive Strength) (P5.0 to P5.5, P6.0 to
P6.7, PJ.0 to PJ.3)...................................................... 23
8.15 Outputs – General-Purpose I/O DVIO Domain
(Full Drive Strength) (P1.0 to P1.7, P2.0 to P2.7,
P3.0 to P3.4, P4.0 to P4.7, P7.0 to P7.5)....................23
8.16 Outputs – General-Purpose I/O DVIO Domain
(Reduced Drive Strength) (P1.0 to P1.7, P2.0 to
P2.7, P3.0 to P3.4, P4.0 to P4.7, P7.0 to P7.5).......... 23
8.17 Output Frequency – General-Purpose I/O
DVCC Domain (P5.0 to P5.5, P6.0 to P6.7, PJ.0
to PJ.3)........................................................................ 24
8.18 Output Frequency – General-Purpose I/O
DVIO Domain (P1.0 to P1.7, P2.0 to P2.7, P3.0 to
P3.4, P4.0 to P4.7, P7.0 to P7.5)................................ 24
8.19 Typical Characteristics – Outputs, Reduced
Drive Strength (PxDS.y = 0)........................................ 25
8.20 Typical Characteristics – Outputs, Full Drive
Strength (PxDS.y = 1)................................................. 26
8.21 Crystal Oscillator, XT1, Low-Frequency Mode........27
4
Submit Document Feedback
8.22 Crystal Oscillator, XT2............................................ 28
8.23 Internal Very-Low-Power Low-Frequency
Oscillator (VLO)...........................................................29
8.24 Internal Reference, Low-Frequency Oscillator
(REFO)........................................................................ 29
8.25 DCO Frequency...................................................... 30
8.26 PMM, Brownout Reset (BOR).................................31
8.27 PMM, Core Voltage.................................................31
8.28 PMM, SVS High Side..............................................31
8.29 PMM, SVM High Side............................................. 32
8.30 PMM, SVS Low Side...............................................32
8.31 PMM, SVM Low Side.............................................. 33
8.32 Wake-up Times From Low-Power Modes and
Reset........................................................................... 33
8.33 Timer_A...................................................................34
8.34 Timer_B...................................................................34
8.35 USCI (UART Mode) Clock Frequency.................... 35
8.36 USCI (UART Mode)................................................ 35
8.37 USCI (SPI Master Mode) Clock Frequency............ 35
8.38 USCI (SPI Master Mode)........................................ 35
8.39 USCI (SPI Slave Mode).......................................... 37
8.40 USCI (I2C Mode).....................................................39
8.41 10-Bit ADC, Power Supply and Input Range
Conditions................................................................... 40
8.42 10-Bit ADC, Timing Parameters..............................40
8.43 10-Bit ADC, Linearity Parameters...........................41
8.44 REF, External Reference........................................ 41
8.45 REF, Built-In Reference.......................................... 42
8.46 Comparator_B.........................................................43
8.47 Flash Memory......................................................... 44
8.48 JTAG and Spy-Bi-Wire Interface.............................44
8.49 DVIO BSL Entry...................................................... 45
9 Detailed Description......................................................46
9.1 CPU.......................................................................... 46
9.2 Operating Modes...................................................... 47
9.3 Interrupt Vector Addresses....................................... 48
9.4 Memory Organization................................................49
9.5 Bootloader (BSL)...................................................... 50
9.6 JTAG Operation........................................................ 52
9.7 Flash Memory........................................................... 54
9.8 RAM.......................................................................... 54
9.9 Peripherals................................................................55
9.10 Input/Output Diagrams............................................78
9.11 Device Descriptors.................................................. 94
10 Device and Documentation Support..........................96
10.1 Getting Started and Next Steps.............................. 96
10.2 Device Nomenclature..............................................96
10.3 Tools and Software................................................. 98
10.4 Documentation Support........................................ 100
10.5 Related Links........................................................ 102
10.6 Support Resources............................................... 102
10.7 Trademarks........................................................... 102
10.8 Electrostatic Discharge Caution............................102
10.9 Export Control Notice............................................102
10.10 Glossary..............................................................102
11 Mechanical, Packaging, and Orderable
Information.................................................................. 103
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from revision C to revision D
Changes from September 28, 2018 to October 20, 2020
Page
• Updated the numbering for sections, tables, figures, and cross-references throughout the document..............1
• Added nFBGA package (ZXH) information throughout document......................................................................1
• Added note about status change for all orderable part numbers in the ZQE package in Device Information ... 1
• Corrected the description of the P2.3/UCB3SOMI/UCB3SCL signals in Table 7-1, Terminal Functions .........10
• Changed the MAX value of the IERASE and IMERASE, IBANK parameters in Section 8.47, Flash Memory ......... 44
Changes from revision B to revision C
Changes from November 26, 2015 to September 27, 2018
Page
• Added Section 6.1, Related Products ................................................................................................................7
• Added color to P1.0 (pin H2) and DVSS (pin F9) to indicate supply from DVIO in Figure 7-2, 80-Pin ZXH or
ZQE Package (Top View) .................................................................................................................................. 8
• Added typical conditions statements at the beginning of Section 8, Specifications .........................................15
• Changed the MIN value of the V(DVCC_BOR_hys) parameter from 60 mV to 50 mV in Section 8.26, PMM,
Brownout Reset (BOR) .................................................................................................................................... 31
• Updated notes (1) and (2) and added note (3) in Section 8.32, Wake-up Times From Low-Power Modes and
Reset ............................................................................................................................................................... 33
• Removed ADC10DIV from the formula for the TYP value in the second row of the tCONVERT parameter in
Section 8.42, 10-Bit ADC, Timing Parameters, because ADC10CLK is after division..................................... 40
• Added second row for tEN_CMP with Test Conditions of "CBPWRMD = 10" and MAX value of 100 µs in Section
8.46, Comparator_B ........................................................................................................................................ 43
• Renamed FCTL4.MGR0 and MGR1 bits in the fMCLK,MGR parameter in Section 8.47, Flash Memory, to be
consistent with header files ..............................................................................................................................44
• Added links to the custom BSL430 package download in Section 9.5, Bootloader (BSL) .............................. 50
• Replaced former section Development Tools Support with Section 10.3, Tools and Software ....................... 98
• Updated list of related documentation in Section 10.4, Documentation Support ...........................................100
Changes from revision A to revision B
Changes from July 31, 2013 to November 25, 2015
Page
• Document format and organization changes throughout, including addition of section numbering....................1
• Added Device Information table..........................................................................................................................1
• Moved Section 4, Functional Block Diagram ..................................................................................................... 3
• Added 16KB RAM option in Figure 4-1, Functional Block Diagram ...................................................................3
• Added Section 6, Device Comparison, and moved Table 6-1 to it......................................................................7
• Added Section 7, Terminal Configuration and Functions, and moved pinout drawings and terminal functions
table to it ............................................................................................................................................................ 8
• Added indication of terminals powered by DVIO in RGC pinout ........................................................................8
• Added indication of terminals powered by DVIO in ZQE pinout......................................................................... 8
• Removed preview YFF pinout............................................................................................................................ 8
• Added SUPPLY column and removed YFF column in Table 7-1, Terminal Functions .....................................10
• Added Section 8.2, ESD Ratings .....................................................................................................................15
• Added note on CVCORE .................................................................................................................................... 15
• Added Section 8.6, Thermal Resistance Characteristics .................................................................................20
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
5
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Moved note on RPull from Section 8.7 to Section 8.8 .......................................................................................21
Changed TYP value of CL,eff with Test Conditions of "XTS = 0, XCAPx = 0" from 2 pF to 1 pF in Section 8.21,
Crystal Oscillator, XT1, Low-Frequency Mode ................................................................................................ 27
Corrected Test Conditions (removed VREF–) for all parameters in Section 8.43 .............................................. 41
Updated Test Conditions for all parameters in Section 8.43, 10-Bit ADC, Linearity Parameters: changed from
"CVREF+ = 20 pF" to "CVeREF+ = 20 pF"; changed from "(VeREF+ – VeREF–)min ≤ (VeREF+ – VeREF–)" to
"1.4 V ≤ (VeREF+ – VeREF–)"...............................................................................................................................41
Added "CVeREF+ = 20 pF" to EI Test Conditions................................................................................................ 41
Added "ADC10SREFx = 11b" to Test Conditions for EG and ET ......................................................................41
Corrected Test Conditions (removed VREF–) for VeREF+, VeREF–, and (VeREF+ – VeREF–) parameters in Section
8.44, REF, External Reference ........................................................................................................................ 41
Changed MIN value of AVCC(min) with Test Conditions of "REFVSEL = {0} for 1.5 V" from 2.2 V to 1.8 V in
Section 8.45, REF, Built-In Reference ............................................................................................................. 42
Corrected spelling of MRG bits in fMCLK,MRG parameter symbol and description............................................. 44
Throughout document, changed all instances of "bootstrap loader" to "bootloader"........................................ 50
Added note to clarify that all JTAG pins are on DVCC......................................................................................52
Added note to indicate that all SBW pins are on DVCC................................................................................... 53
Corrected spelling of NMIIFG in Table 9-10, System Module Interrupt Vector Registers ................................ 58
Removed YFF package information from Table 9-12, TA0 Signal Connections .............................................. 60
Removed YFF package information from Table 9-13, TA1 Signal Connections .............................................. 61
Removed YFF package information from Table 9-14, TA2 Signal Connections .............................................. 62
Removed YFF package information from Table 9-15, TB0 Signal Connections ..............................................63
Changed Figure 9-8, Port P5 (P5.3) Diagram (added P5SEL.2 and XT2BYPASS inputs with AND and OR
gates) ...............................................................................................................................................................85
Changed P5SEL.3 column from X to 0 for "P5.3 (I/O)" rows............................................................................85
Changed Figure 9-10, Port P5 (P5.5) Diagram (added P5SEL.5 input and OR gate)......................................87
Changed P5SEL.5 column from X to 0 for "P5.5 (I/O)" rows............................................................................87
Added Section 10 and moved Development Tools Support, Device and Development Tool Nomenclature,
Trademarks, and Electrostatic Discharge Caution sections to it.......................................................................96
Added Section 11, Mechanical, Packaging, and Orderable Information ........................................................103
Changes from initial release to revision A
REVISION
CHANGES
Updated PRODUCT PREVIEW release.
SLAS903A
July 2013
Added Section 2.
Changed Section 3.
Added Development Tools Support and Section 10.2.
SLAS903
July 2013
6
PRODUCT PREVIEW release
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
6 Device Comparison
Table 6-1 summarizes the available family members.
Table 6-1. Device Comparison
USCI
ADC10
_A
(Ch)
COMP
_B
(Ch)
I/Os
DVCC(5)
I/Os
DVIO(6)
BSL
TYPE
PACKAGE
4
10 ext,
2 int
8
18
35
I2C
64 RGC,
80 ZXH,
80 ZQE
4
4
N/A
8
18
35
I2C
64 RGC,
80 ZXH,
80 ZQE
7
4
4
10 ext,
2 int
8
18
35
I2C
64 RGC,
80 ZXH,
80 ZQE
5, 3, 3
7
4
4
N/A
8
18
35
I2C
64 RGC,
80 ZXH,
80 ZQE
32
5, 3, 3
7
4
4
10 ext,
2 int
8
18
35
UART
64 RGC,
80 ZXH,
80 ZQE
128
32
5, 3, 3
7
4
4
N/A
8
18
35
UART
64 RGC,
80 ZXH,
80 ZQE
MSP430F5253
128
16
5, 3, 3
7
4
4
10 ext,
2 int
8
18
35
UART
64 RGC,
80 ZXH,
80 ZQE
MSP430F5252
128
16
5, 3, 3
7
4
4
N/A
8
18
35
UART
64 RGC,
80 ZXH,
80 ZQE
CHANNEL
A:
UART,
IrDA, SPI
CHANNEL
B:
SPI, I2C
DEVICE(1) (2)
FLASH
(KB)
SRAM
(KB)
Timer_A(3)
Timer_B(4)
MSP430F5259
128
32
5, 3, 3
7
4
MSP430F5258
128
32
5, 3, 3
7
MSP430F5257
128
16
5, 3, 3
MSP430F5256
128
16
MSP430F5255
128
MSP430F5254
(1)
(2)
(3)
(4)
(5)
(6)
For the most current package and ordering information, see the Package Option Addendum in Section 11, or see the TI website at
www.ti.com.
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/
packaging.
Each number in the sequence represents an instantiation of Timer_A with its associated number of capture compare registers and
PWM output generators available. For example, a number sequence of 3, 5 would represent two instantiations of Timer_A, the first
instantiation having 3 and the second instantiation having 5 capture compare registers and PWM output generators, respectively.
Each number in the sequence represents an instantiation of Timer_B with its associated number of capture compare registers and
PWM output generators available. For example, a number sequence of 3, 5 would represent two instantiations of Timer_B, the first
instantiation having 3 and the second instantiation having 5 capture compare registers and PWM output generators, respectively.
All of these I/Os are on a single voltage rail supplied by DVCC.
All of these I/Os are on a single voltage rail supplied by DVIO.
6.1 Related Products
For information about other devices in this family of products or related products, see the following links.
16-bit and 32-bit microcontrollers
High-performance, low-power solutions to enable the autonomous future
Products for MSP430 ultra-low-power microcontrollers
One platform. One ecosystem. Endless possibilities.
Companion products for MSP430F5259
Review products that are frequently purchased or used in conjunction with this product.
Reference designs
Find reference designs that leverage the best in TI technology to solve your system-level challenges.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
7
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
7 Terminal Configuration and Functions
7.1 Pin Diagrams
P7.0/UCA2TXD/UCA2SIMO
P7.1/UCA2RXD/UCA2SOMI
P7.2/UCB2CLK/UCA2STE
P7.3/UCB2SIMO/UCB2SDA
P7.4/UCB2SOMI/UCB2SCL
P7.5/UCB2STE/UCA2CLK
BSLEN
RST/NMI
P5.2/XT2IN
P5.3/XT2OUT
TEST/SBWTCK
PJ.0/TDO
PJ.1/TDI/TCLK
PJ.2/TMS
PJ.3/TCK
RSTDVCC/SBWTDIO
Figure 7-1 shows the pinout of the 64-pin RGC package.
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
6
43
P4.2/PM_UCB1SOMI/PM_UCB1SCL
P6.6/CB6/A6
7
42
P4.1/PM_UCB1SIMO/PM_UCB1SDA
P6.7/CB7/A7
8
41
P4.0/PM_UCB1STE/PM_UCA1CLK
P5.0/A8/VeREF+
9
40
DVIO
P5.1/A9/VeREF-
10
39
DVSS
AVCC
11
38
P3.4/UCA0RXD/UCA0SOMI
P5.4/XIN
12
37
P3.3/UCA0TXD/UCA0SIMO
P5.5/XOUT
13
36
P3.2/UCB0CLK/UCA0STE
AVSS
14
35
P3.1/UCB0SOMI/UCB0SCL
DVCC
15
34
P3.0/UCB0SIMO/UCB0SDA
DVSS
33
16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Supplied by DVIO
P2.7/UCB0STE/UCA0CLK
P2.6/RTCCLK/DMAE0
P2.5/UCB3STE/UCA3CLK
P4.3/PM_UCB1CLK/PM_UCA1STE
P6.5/CB5/A5
P2.4/UCB3CLK/UCA3STE
44
P2.3/UCB3SOMI/UCB3SCL
5
P2.2/UCB3SIMO/UCB3SDA
P4.4/PM_UCA1TXD/PM_UCA1SIMO
P6.4/CB4/A4
P2.1/TA1.2
45
P2.0/TA1.1
4
P1.7/TA1.0
P4.5/PM_UCA1RXD/PM_UCA1SOMI
P6.3/TA2.2/CB3/A3
P1.6/TA1CLK/CBOUT
P4.6/PM_UCA3TXD/PM_UCA3SIMO
46
P1.5/TA0.4
47
3
P1.4/TA0.3
2
P6.2/TA2.1/CB2/A2
P1.3/TA0.2
P6.1/TA2.0/CB1/A1
P1.2/TA0.1
P4.7/PM_UCA3RXD/PM_UCA3SOMI
P1.1/TA0.0
48
P1.0/TA0CLK/ACLK
1
VCORE
P6.0/TA2CLK/SMCLK/CB0/A0
Figure 7-1. 64-Pin RGC Package (Top View)
8
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Figure 7-2 shows the pinout of the 80-pin ZXH or ZQE package.
TEST RST/NMI P7.5
P7.4
P7.3
P7.1
A4
A5
A7
A8
A9
P5.3
B4
P5.2
B5
PJ.1
C4
PJ.0
C5
C6
P6.7
D3
D4
D5
D6
E3
E4
E5
E6
E7
E8
F3
F4
F5
F6
F7
F8
F9
P6.0 RSTDVCC PJ.2
A3
A1
A2
PJ.3
B3
A6
BSLEN P7.2
B6
B7
P6.2
B1
P6.1
B2
P7.0
P6.4
C1
P6.3
C2
P6.6
D1
P6.5
D2
P5.0
P5.1
E1
E2
P5.4
AVCC
F1
F2
P5.5
AVSS
G1
G2
G3
P1.3
G4
P1.6
G5
P2.1
G6
P3.4
G7
P3.2
G8
P3.3
G9
DVCC
P1.0
P1.1
P1.4
P1.7
P2.3
P2.7
P3.0
P3.1
H1
H2
H3
H4
H5
H6
H7
H8
H9
P1.5
J4
P2.0
J5
P2.2
J6
P2.4
J7
P2.5
J8
P2.6
J9
B8
B9
P4.7
C7
P4.6
C8
P4.5
C9
P4.4
D7
P4.3
D8
P4.2
D9
P4.1
P4.0
DVIO
E9
DVSS
DVSS VCORE P1.2
J3
J1
J2
Supplied by DVIO
Figure 7-2. 80-Pin ZXH or ZQE Package (Top View)
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
9
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
7.2 Signal Descriptions
Table 7-1 describes the device signals.
Table 7-1. Terminal Functions
TERMINAL
NO.(2)
NAME
RGC
I/O(1)
SUPPLY
DESCRIPTION
ZXH,
ZQE
General-purpose digital I/O with port interrupt
TA2 clock signal TA2CLK input
P6.0/TA2CLK/SMCLK/CB0/A0
1
A1
I/O
DVCC
SMCLK output
Comparator_B input CB0
Analog input A0 for ADC (not available on all device types)
General-purpose digital I/O with port interrupt
TA2 CCR0 capture: CCI0A input, compare: Out0 output
P6.1/TA2.0/CB1/A1
2
B2
I/O
DVCC
Comparator_B input CB1
Analog input A1 for ADC (not available on all device types)
BSL transmit output
General-purpose digital I/O with port interrupt
TA2 CCR1 capture: CCI1A input, compare: Out1 output
P6.2/TA2.1/CB2/A2
3
B1
I/O
DVCC
Comparator_B input CB2
Analog input A2 for ADC (not available on all device types)
BSL receive input
General-purpose digital I/O with port interrupt
P6.3/TA2.2/CB3/A3
4
C2
I/O
DVCC
TA2 CCR2 capture: CCI2A input, compare: Out2 output
Comparator_B input CB3
Analog input A3 for ADC (not available on all device types)
General-purpose digital I/O with port interrupt
P6.4/CB4/A4
5
C1
I/O
DVCC
Comparator_B input CB4
Analog input A4 for ADC (not available on all device types)
General-purpose digital I/O with port interrupt
P6.5/CB5/A5
6
D2
I/O
DVCC
Comparator_B input CB5
Analog input A5 for ADC (not available on all device types)
General-purpose digital I/O with port interrupt
P6.6/CB6/A6
7
D1
I/O
DVCC
Comparator_B input CB6
Analog input A6 for ADC (not available on all device types)
General-purpose digital I/O with port interrupt
P6.7/CB7/A7
8
D3
I/O
DVCC
Comparator_B input CB7
Analog input A7 for ADC (not available on all device types)
General-purpose digital I/O
P5.0/A8/VeREF+
9
E1
I/O
DVCC
Analog input A8 for ADC (not available on all device types)
Input for an external reference voltage to the ADC (not
available on all device types)
General-purpose digital I/O
P5.1/A9/VeREF-
10
E2
AVCC
11
F2
10
Submit Document Feedback
I/O
DVCC
Analog input A9 for ADC (not available on all device types)
Negative terminal for the ADC reference voltage for an external
applied reference voltage (not available on all device types)
Analog power supply
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 7-1. Terminal Functions (continued)
TERMINAL
NO.(2)
NAME
I/O(1)
SUPPLY
DESCRIPTION
RGC
ZXH,
ZQE
P5.4/XIN
12
F1
I/O
DVCC
P5.5/XOUT
13
G1
I/O
DVCC
AVSS
14
G2
Analog ground supply
DVCC
15
H1
Digital power supply
DVSS
16
J1
Digital ground supply
VCORE(4)
17
J2
P1.0/TA0CLK/ACLK(5)
18
H2
DVCC
General-purpose digital I/O
Input terminal for crystal oscillator XT1(3)
General-purpose digital I/O
Output terminal of crystal oscillator XT1
Regulated core power supply output (internal use only, no
external current loading)
General-purpose digital I/O with port interrupt
I/O
DVIO
TA0 clock signal TA0CLK input
ACLK output (divided by 1, 2, 4, 8, 16, or 32)
P1.1/TA0.0(5)
19
H3
I/O
DVIO
P1.2/TA0.1(5)
20
J3
I/O
DVIO
P1.3/TA0.2(5)
21
G4
I/O
DVIO
P1.4/TA0.3(5)
22
H4
I/O
DVIO
P1.5/TA0.4(5)
23
J4
I/O
DVIO
P1.6/TA1CLK/CBOUT(5)
24
G5
I/O
DVIO
General-purpose digital I/O with port interrupt
TA0 CCR0 capture: CCI0A input, compare: Out0 output
General-purpose digital I/O with port interrupt
TA0 CCR1 capture: CCI1A input, compare: Out1 output
General-purpose digital I/O with port interrupt
TA0 CCR2 capture: CCI2A input, compare: Out2 output
General-purpose digital I/O with port interrupt
TA0 CCR3 capture: CCI3A input compare: Out3 output
General-purpose digital I/O with port interrupt
TA0 CCR4 capture: CCI4A input, compare: Out4 output
General-purpose digital I/O with port interrupt
TA1 clock signal TA1CLK input
Comparator_B output
P1.7/TA1.0(5)
25
H5
I/O
DVIO
P2.0/TA1.1(5)
26
J5
I/O
DVIO
P2.1/TA1.2(5)
27
G6
I/O
DVIO
P2.2/UCB3SIMO/UCB3SDA(5)
28
J6
I/O
DVIO
General-purpose digital I/O with port interrupt
TA1 CCR0 capture: CCI0A input, compare: Out0 output
General-purpose digital I/O with port interrupt
TA1 CCR1 capture: CCI1A input, compare: Out1 output
General-purpose digital I/O with port interrupt
TA1 CCR2 capture: CCI2A input, compare: Out2 output
General-purpose digital I/O with port interrupt
Slave in, master out – USCI_B3 SPI mode
I2C data – USCI_B3 I2C mode
General-purpose digital I/O with port interrupt
P2.3/UCB3SOMI/UCB3SCL(5)
29
H6
I/O
DVIO
Slave out, master in – USCI_B3 SPI mode
I2C clock – USCI_B3 I2C mode
General-purpose digital I/O with port interrupt
P2.4/UCB3CLK/UCA3STE(5)
30
J7
I/O
DVIO
Clock signal input – USCI_B3 SPI slave mode
Clock signal output – USCI_B3 SPI master mode
Slave transmit enable – USCI_A3 SPI mode
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
11
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 7-1. Terminal Functions (continued)
TERMINAL
NO.(2)
NAME
RGC
I/O(1)
SUPPLY
DESCRIPTION
ZXH,
ZQE
General-purpose digital I/O with port interrupt
P2.5/UCB3STE/UCA3CLK(5)
31
J8
I/O
DVIO
Slave transmit enable – USCI_B3 SPI mode
Clock signal input – USCI_A3 SPI slave mode
Clock signal output – USCI_A3 SPI master mode
General-purpose digital I/O with port interrupt
P2.6/RTCCLK/DMAE0(5)
32
J9
I/O
DVIO
RTC clock output for calibration
DMA external trigger input
General-purpose digital I/O
P2.7/UCB0STE/UCA0CLK(5)
33
H7
I/O
DVIO
Slave transmit enable – USCI_B0 SPI mode
Clock signal input – USCI_A0 SPI slave mode
Clock signal output – USCI_A0 SPI master mode
General-purpose digital I/O
P3.0/UCB0SIMO/UCB0SDA(5)
34
H8
I/O
DVIO
Slave in, master out – USCI_B0 SPI mode
I2C data – USCI_B0 I2C mode
General-purpose digital I/O
P3.1/UCB0SOMI/UCB0SCL(5)
35
H9
I/O
DVIO
Slave out, master in – USCI_B0 SPI mode
I2C clock – USCI_B0 I2C mode
General-purpose digital I/O
P3.2/UCB0CLK/UCA0STE(5)
36
G8
I/O
DVIO
Clock signal input – USCI_B0 SPI slave mode
Clock signal output – USCI_B0 SPI master mode
Slave transmit enable – USCI_A0 SPI mode
General-purpose digital I/O
P3.3/UCA0TXD/UCA0SIMO(5)
37
G9
I/O
DVIO
Transmit data – USCI_A0 UART mode
Slave in, master out – USCI_A0 SPI mode
General-purpose digital I/O
P3.4/UCA0RXD/UCA0SOMI(5)
38
G7
DVSS
39
F9
Digital ground supply
DVIO(6)
40
E9
Digital I/O power supply
I/O
DVIO
Receive data – USCI_A0 UART mode
Slave out, master in – USCI_A0 SPI mode
General-purpose digital I/O with reconfigurable port mapping
secondary function
P4.0/PM_UCB1STE/
PM_UCA1CLK(5)
41
E8
I/O
DVIO
Default mapping: Slave transmit enable – USCI_B1 SPI mode
Default mapping: Clock signal input – USCI_A1 SPI slave mode
Default mapping: Clock signal output – USCI_A1 SPI master
mode
P4.1/PM_UCB1SIMO/
PM_UCB1SDA(5)
42
E7
I/O
DVIO
General-purpose digital I/O with reconfigurable port mapping
secondary function
Default mapping: Slave in, master out – USCI_B1 SPI mode
Default mapping: I2C data – USCI_B1 I2C mode
P4.2/PM_UCB1SOMI/
PM_UCB1SCL(5)
43
D9
I/O
DVIO
General-purpose digital I/O with reconfigurable port mapping
secondary function
Default mapping: Slave out, master in – USCI_B1 SPI mode
Default mapping: I2C clock – USCI_B1 I2C mode
12
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 7-1. Terminal Functions (continued)
TERMINAL
NO.(2)
NAME
RGC
I/O(1)
SUPPLY
DESCRIPTION
ZXH,
ZQE
General-purpose digital I/O with reconfigurable port mapping
secondary function
P4.3/PM_UCB1CLK/
PM_UCA1STE(5)
44
D8
I/O
DVIO
Default mapping: Clock signal input – USCI_B1 SPI slave mode
Default mapping: Clock signal output – USCI_B1 SPI master
mode
Default mapping: Slave transmit enable – USCI_A1 SPI mode
P4.4/PM_UCA1TXD/
PM_UCA1SIMO(5)
45
D7
I/O
DVIO
General-purpose digital I/O with reconfigurable port mapping
secondary function
Default mapping: Transmit data – USCI_A1 UART mode
Default mapping: Slave in, master out – USCI_A1 SPI mode
P4.5/PM_UCA1RXD/
PM_UCA1SOMI(5)
46
C9
I/O
DVIO
General-purpose digital I/O with reconfigurable port mapping
secondary function
Default mapping: Receive data – USCI_A1 UART mode
Default mapping: Slave out, master in – USCI_A1 SPI mode
P4.6/PM_UCA3TXD/
PM_UCA3SIMO(5)
47
C8
I/O
DVIO
General-purpose digital I/O with reconfigurable port mapping
secondary function
Default mapping: Transmit data – USCI_A3 UART mode
Default mapping: Slave in, master out – USCI_A3 SPI mode
P4.7/PM_UCA3RXD/
PM_UCA3SOMI(5)
48
C7
I/O
DVIO
General-purpose digital I/O with reconfigurable port mapping
secondary function
Default mapping: Receive data – USCI_A3 UART mode
Default mapping: Slave out, master in – USCI_A3 SPI mode
General-purpose digital I/O
P7.0/UCA2TXD/UCA2SIMO(5)
49
B8, B9
I/O
DVIO
Transmit data – USCI_A2 UART mode
Slave in, master out – USCI_A2 SPI mode
General-purpose digital I/O
P7.1/UCA2RXD/UCA2SOMI(5)
50
A9
I/O
DVIO
Receive data – USCI_A2 UART mode
Slave out, master in – USCI_A2 SPI mode
General-purpose digital I/O
P7.2/UCB2CLK/UCA2STE(5)
51
B7
I/O
DVIO
Clock signal input – USCI_B2 SPI slave mode
Clock signal output – USCI_B2 SPI master mode
Slave transmit enable – USCI_A2 SPI mode
General-purpose digital I/O
P7.3/UCB2SIMO/UCB2SDA(5)
52
A8
I/O
DVIO
Slave in, master out – USCI_B2 SPI mode
I2C data – USCI_B2 I2C mode
General-purpose digital I/O
P7.4/UCB2SOMI/UCB2SCL(5)
53
A7
I/O
DVIO
Slave out, master in – USCI_B2 SPI mode
I2C clock – USCI_B2 I2C mode
General-purpose digital I/O
P7.5/UCB2STE/UCA2CLK(5)
54
A6
I/O
DVIO
BSLEN(5)
55
B6
I
DVIO
RST/NMI(5)
56
A5
I
DVIO
Slave transmit enable – USCI_B2 SPI mode
Clock signal input – USCI_A2 SPI slave mode
Clock signal output – USCI_A2 SPI master mode
Copyright © 2020 Texas Instruments Incorporated
BSL enable with internal pulldown
Reset input active low(7) (8)
Nonmaskable interrupt input(7)
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
13
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 7-1. Terminal Functions (continued)
TERMINAL
NO.(2)
NAME
I/O(1)
SUPPLY
RGC
ZXH,
ZQE
P5.2/XT2IN
57
B5
I/O
DVCC
P5.3/XT2OUT
58
B4
I/O
DVCC
TEST/SBWTCK(10)
59
A4
I
DVCC
PJ.0/TDO(11)
60
C5
I/O
DVCC
PJ.1/TDI/TCLK(11)
61
C4
I/O
DVCC
PJ.2/TMS(11)
62
A3
I/O
DVCC
PJ.3/TCK(11)
63
B3
I/O
DVCC
DESCRIPTION
General-purpose digital I/O
Input terminal for crystal oscillator XT2(9)
General-purpose digital I/O
Output terminal of crystal oscillator XT2
Test mode pin – Selects four wire JTAG operation
Spy-Bi-Wire input clock when Spy-Bi-Wire operation activated
General-purpose digital I/O
JTAG test data output port
General-purpose digital I/O
JTAG test data input or test clock input
General-purpose digital I/O
JTAG test mode select
General-purpose digital I/O
JTAG test clock
Reset input active low(12)
RSTDVCC/SBWTDIO(11)
64
A2
Reserved
N/A
(13)
QFN Pad
Pad
N/A
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
14
I/O
DVCC
Spy-Bi-Wire data input/output when Spy-Bi-Wire operation
activated
Reserved
QFN package pad. Connection to VSS recommended.
I = input, O = output
N/A = not available
When in crystal bypass mode, XIN can be configured so that it can support an input digital waveform with swing levels from DVSS to
DVCC or DVSS to DVIO. In this case, the pin must be configured properly for the intended input swing.
VCORE is for internal use only. No external current loading is possible. VCORE should be connected only to the recommended
capacitor value, CVCORE (see Section 8.3).
This pin function is supplied by DVIO. See Section 8.8 for input and output requirements.
The voltage on DVIO is not supervised or monitored.
This pin is configurable as reset or NMI and resides on the DVIO supply domain. When driven from external, the input swing levels
from DVSS to DVIO are required.
When this pin is configured as reset, the internal pullup resistor is enabled by default.
When in crystal bypass mode, XT2IN can be configured so that it can support an input digital waveform with swing levels from DVSS
to DVCC or DVSS to DVIO. In this case, the must pin be configured properly for the intended input swing.
See Section 9.5.1 and Section 9.6 for use with BSL and JTAG functions, respectively.
See Section 9.6 for use with JTAG function.
This nonconfigurable reset resides on the DVCC supply domain and has an internal pullup to DVCC. When driven from external, input
swing levels from DVSS to DVCC are required. This reset must be used for Spy-Bi-Wire communication and is not the same RST/NMI
reset as found on other devices in the MSP430 family. Refer to Section 9.5.1 and Section 9.6 for details regarding the use of this pin.
C6, D4, D5, D6, E3, E4, E5, E6, F3, F4, F5, F6, F7, F8, G3 are reserved and should be connected to ground.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8 Specifications
All graphs in this section are for typical conditions, unless otherwise noted.
Typical (TYP) values are specified at VCC = 3.3 V and TA = 25°C, unless otherwise noted.
8.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
Voltage applied at VCC to VSS
–0.3
4.1
V
Voltage applied at VIO to VSS
–0.3
2.2
V
Voltage applied to any pin (excluding VCORE and VIO pins)(2)
–0.3
VCC + 0.3
V
Voltage applied to VIO pins
–0.3
VIO + 0.2
V
±2
mA
–55
150
°C
Diode current at any device pin
Storage temperature, Tstg (3)
(1)
(2)
(3)
UNIT
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages referenced to VSS. VCORE is for internal device use only. No external DC loading or voltage should be applied.
Higher temperature may be applied during board soldering according to the current JEDEC J-STD-020 specification with peak reflow
temperatures not higher than classified on the device label on the shipping boxes or reels.
8.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC
JS-001(1)
UNIT
±1000
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
V
±250
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Pins listed as
±1000 V may actually have higher performance.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Pins listed as
±250 V may actually have higher performance.
8.3 Recommended Operating Conditions
MIN
Supply voltage during program execution
and flash programming (AVCC = DVCC)(1) (2)
VCC
(3)
NOM
MAX
PMMCOREVx = 0
1.8
3.6
PMMCOREVx = 0, 1
2.0
3.6
PMMCOREVx = 0, 1, 2
2.2
3.6
PMMCOREVx = 0, 1, 2, 3
2.4
3.6
(2)
Supply voltage applied to DVIO referenced to VSS
VSS
Supply voltage (AVSS = DVSS)
TA
Operating free-air temperature
–40
85
°C
TJ
Operating junction temperature
–40
85
°C
Recommended capacitor at
CDVCC/ C
Capacitor ratio of DVCC to VCORE
fSYSTEM
(1)
0
VCORE(4)
CVCORE
Processor frequency (maximum MCLK
frequency)(5) (see Figure 8-3)
1.98
V
VIO
VCORE
1.62
UNIT
V
V
470
nF
10
PMMCOREVx = 0 (default condition),
1.8 V ≤ VCC ≤ 3.6 V
0
PMMCOREVx = 1, 2.0 V ≤ VCC ≤ 3.6 V
0
12.0
PMMCOREVx = 2, 2.2 V ≤ VCC ≤ 3.6 V
0
20.0
PMMCOREVx = 3, 2.4 V ≤ VCC ≤ 3.6 V
0
25.0
8.0
MHz
TI recommends powering AVCC and DVCC from the same source. A maximum difference of 0.3 V between AVCC and DVCC can be
tolerated during power up and operation.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
15
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
(2)
(3)
(4)
(5)
During VCC and VIO power up, it is required that VIO ≥ VCC during the ramp up phase of VIO. During VCC and VIO power down, it is
required that VIO ≥ VCC during the ramp down phase of VIO (see Figure 8-1).
The minimum supply voltage is defined by the supervisor SVS levels when it is enabled. See the Section 8.28 threshold parameters for
the exact values and further details.
TI recommends a capacitor tolerance of ±20% or better.
Modules may have a different maximum input clock specification. See the specification of the respective module in this data sheet.
VCC
VIO
VIO,min
VSS
t
VCC ≤ VIO
while VIO < VIO,min
VIO ≤ VCC
VCC ≤ VIO
while VIO < VIO,min
NOTE: The device supports continuous operation with VCC = VSS while VIO is fully within its specification. During this time, the generalpurpose I/Os that reside on the VIO supply domain are configured as inputs and pulled down to VSS through their internal pulldown
resistors. RST/NMI is high impedance. BSLEN is configured as an input and is pulled down to VSS through its internal pulldown resistor.
When VCC reaches above the BOR threshold, the general-purpose I/Os become high-impedance inputs (no pullup or pulldown enabled),
RST/NMI becomes an input pulled up to VIO through its internal pullup resistor, and BSLEN remains pulled down to VSS through its
internal pulldown resistor.
NOTE: Under certain condtions during the rising transition of VCC, the general-purpose I/Os that reside on the VIO supply domain may
actively transition high momentarily before settling to high-impedance inputs. These voltage transitions are temporary (typically resolving
to high impedance inputs when VCC exceeds approximately 0.9 V) and are bounded by the VIO supply.
Figure 8-1. VCC and VIO Power Sequencing
16
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
VCC
V(SVSH_+), min
tWAKE_UP_RESET
tWAKE_UP_RESET
tWAKE_UP_RESET
DVCC
VCC
VIT+
RSTDVCC
VCC ≥ VRSTDVCC
VRSTDVCC = VCC
VIO
tWAKE_UP_RESET
tWAKE_UP_RESET
DVIO
VIO
VIT+
RST
VIO ≥ VRST
VRST = VIO
t
NOTE:The device remains in reset based on the conditions of the RSTDVCC and RST pins and the voltage present on DVCC voltage
supply. If RSTDVCC or RST is held at a logic low or if DVCC is below the SVSH_+ minimum threshold, the device remains in its reset
condition; that is, these conditions form a logical OR with respect to device reset.
Figure 8-2. Reset Timing
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
17
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
25
System Frequency - MHz
3
20
2
2, 3
1
1, 2
1, 2, 3
0, 1
0, 1, 2
0, 1, 2, 3
12
8
0
0
1.8
2.0
2.2
2.4
3.6
Supply Voltage - V
NOTE: The numbers within the fields denote the supported PMMCOREVx settings.
Figure 8-3. Maximum System Frequency
8.4 Active Mode Supply Current Into VCC Excluding External Current
over recommended operating free-air temperature (unless otherwise noted)(1) (2) (3)
PARAMETER
IAM, Flash
IAM, RAM
(1)
(2)
(3)
18
EXECUTION
MEMORY
Flash
RAM
FREQUENCY (fDCO = fMCLK = fSMCLK)
VCC
3.0 V
3.0 V
PMMCOREVx
1 MHz
8 MHz
12 MHz
TYP
MAX
TYP
MAX
0
0.36
0.47
2.32
2.60
1
0.40
2
0.44
20 MHz
TYP
MAX
2.65
4.0
4.4
2.90
3.10
MAX
4.3
7.1
7.7
4.6
7.6
3
0.46
0
0.20
1
0.22
1.35
2.0
2
0.24
1.50
2.2
3.7
3
0.26
1.60
2.4
3.9
0.29
1.20
25 MHz
TYP
TYP
UNIT
MAX
mA
10.1
11.0
1.30
2.2
mA
4.2
5.3
6.2
All inputs are tied to 0 V or to VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal MS1V-T1K crystal with a load capacitance of 12.5 pF. The internal and external
load capacitance are chosen to closely match the required 12.5 pF.
Characterized with program executing typical data processing.
fACLK = 32786 Hz, fDCO = fMCLK = fSMCLK at specified frequency.
XTS = CPUOFF = SCG0 = SCG1 = OSCOFF= SMCLKOFF = 0.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.5 Low-Power Mode Supply Currents (Into VCC) Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1) (2)
TEMPERATURE (TA)
PARAMETER
VCC
PMMCOREVx
–40°C
TYP
ILPM0,1MHz
Low-power mode 0(3) (9)
ILPM2
Low-power mode 2(4) (9)
MAX
TYP
85°C
MAX
UNIT
TYP
MAX
73
78
91
84
93
103
3.0 V
3
89
95
105
101
112
124
2.2 V
0
6.7
6.7
12
10.6
13
29
3.0 V
3
7.2
7.2
13
11.6
14
30
0
1.8
2.1
3.4
8.4
1
1.9
2.2
3.6
8.7
2
2.0
2.4
3.8
9.0
0
2.0
2.3
3.6
8.6
1
2.1
2.5
3.8
8.9
2
2.2
2.6
3.9
9.2
3
2.3
2.7
4.1
4.0
9.2
25
0
1.3
1.6
2.9
2.6
8.5
24
1
1.3
1.6
2.8
8.8
2
1.4
1.7
2.9
9.2
3
1.5
1.8
3.2
2.9
9.2
25
0
1.1
1.3
1.7
2.6
7.5
22
1
1.3
1.4
2.7
7.7
2
1.4
1.4
2.8
7.9
3.0 V
ILPM3,VLO
60°C
TYP
0
Low-power mode 3, crystal
mode(5) (9)
Low-power mode 3,
VLO mode(6) (9)
MAX
2.2 V
2.2 V
ILPM3,XT1LF
25°C
3.0 V
3.1
24
µA
µA
µA
µA
ILPM4
Low-power mode 4(7) (9)
3.0 V
1.5
1.5
1.8
2.8
7.9
23
ILPM4.5
Low-power mode 4.5(8)
3.0 V
0.15
0.18
0.35
0.26
0.5
1.0
µA
IDVIO_START
Current supplied from DVIO
while DVCC = AVCC = 0 V,
DVIO = 1.62 V to 1.98 V,
All DVIO I/O floating
including BSLEN and
RST/NMI
0V
1.40
1.40
2.0
1.45
1.5
2.1
µA
3
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
µA
All inputs are tied to 0 V or to VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal MS1V-T1K crystal with a load capacitance of 12.5 pF. The internal and external
load capacitance are chosen to closely match the required 12.5 pF.
Current for the watchdog timer clocked by SMCLK included. ACLK = low-frequency crystal operation (XTS = 0, XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 0, SCG1 = 0, OSCOFF = 0 (LPM0), fACLK = 32768 Hz, fMCLK = 0 MHz, fSMCLK = fDCO = 1 MHz
Current for watchdog timer and RTC clocked by ACLK included. ACLK = low-frequency crystal operation (XTS = 0, XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 0, SCG1 = 1, OSCOFF = 0 (LPM2), fACLK = 32768 Hz, fMCLK = 0 MHz, fSMCLK = fDCO = 0 MHz, DCO setting = 1MHz operation, DCO bias generator enabled.)
Current for watchdog timer and RTC clocked by ACLK included. ACLK = low-frequency crystal operation (XTS = 0, XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3), fACLK = 32768 Hz, fMCLK = fSMCLK = fDCO = 0 MHz
Current for watchdog timer and RTC clocked by ACLK included. ACLK = VLO.
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3), fACLK = fVLO, fMCLK = fSMCLK = fDCO = 0 MHz
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 1 (LPM4), fDCO = fACLK = fMCLK = fSMCLK = 0 MHz
Internal regulator disabled. No data retention.
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 1, PMMREGOFF = 1 (LPM4.5), fDCO = fACLK = fMCLK = fSMCLK = 0 MHz
Current for brownout and high-side supervisor (SVSH) normal mode included. Low-side supervisor (SVSL) and low-side monitor (SVM
L) disabled. High-side monitor (SVMH) disabled. RAM retention enabled.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
19
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.6 Thermal Resistance Characteristics
THERMAL METRIC(1) (2)
RθJA
Junction-to-ambient thermal resistance, still air
RθJC(TOP)
Junction-to-case (top) thermal resistance
RθJC(BOTTOM)
Junction-to-case (bottom) thermal resistance
RθJB
Junction-to-board thermal resistance
ΨJT
Junction-to-package-top thermal characterization parameter
ΨJB
Junction-to-board thermal characterization parameter
(1)
(2)
(3)
20
VALUE
VQFN 64 (RGC)
29.3
BGA 80 (ZQE)
52.0
VQFN 64 (RGC)
14.2
BGA 80 (ZQE)
23.9
VQFN 64 (RGC)
BGA 80 (ZQE)
1.1
N/A(3)
VQFN 64 (RGC)
8.2
BGA 80 (ZQE)
29.3
VQFN 64 (RGC)
0.2
BGA 80 (ZQE)
0.5
VQFN 64 (RGC)
8.1
BGA 80 (ZQE)
29.3
UNIT
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
For more information about traditional and new thermal metrics, see Semiconductor and IC Package Thermal Metrics.
These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RθJC] value, which is based on a
JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/
JEDEC standards:
• JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
• JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
• JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
• JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements
N/A = not applicable
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.7 Schmitt-Trigger Inputs – General-Purpose I/O DVCC Domain
(P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3, RSTDVCC)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER(1)
TEST CONDITIONS
VIT+
Positive-going input threshold voltage
VIT–
Negative-going input threshold voltage
Vhys
Input voltage hysteresis (VIT+ – VIT–)
RPull
Pullup or pulldown resistor
For pullup: VIN = VSS,
For pulldown: VIN = VCC
CI
Input capacitance
VIN = VSS or VCC
(1)
VCC
MIN
TYP
1.8 V
0.80
1.40
3V
1.50
2.10
1.8 V
0.45
1.00
3V
0.75
1.65
1.8 V
0.3
0.8
3V
0.4
1.0
20
35
MAX
50
5
UNIT
V
V
V
kΩ
pF
These same parametrics apply to the clock input pin when crystal bypass mode is used on XT1 (XIN) or XT2 (XT2IN).
8.8 Schmitt-Trigger Inputs – General-Purpose I/O DVIO Domain
(P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P7.0 to P7.5, RST/NMI, BSLEN)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT+
Positive-going input threshold voltage
VCC = 3.0 V
VIT–
Negative-going input threshold voltage
VCC = 3.0 V
Vhys
Input voltage hysteresis (VIT+ – VIT–)
VCC = 3.0 V
RPull
Pullup or pulldown resistor(1)
For pullup: VIN = VSS,
For pulldown: VIN = VIO
CI
Input capacitance
VIN = VSS or VIO
(1)
VIO
MIN
TYP
MAX
1.62 V
0.8
1.25
1.98 V
1.1
1.40
UNIT
V
1.62 V
0.3
0.7
1.98 V
0.5
1.0
1.62 V to 1.98 V
0.3
0.8
V
50
kΩ
20
35
5
V
pF
Also applies to the RST pin when the pullup or pulldown resistor is enabled.
8.9 Inputs – Interrupts DVCC Domain Port P6
(P6.0 to P6.7)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
t(int)
(1)
External interrupt
timing(1)
TEST CONDITIONS
External trigger pulse duration to set interrupt flag
VCC
MIN
1.8 V, 3 V
MAX
20
UNIT
ns
An external signal sets the interrupt flag every time the minimum interrupt pulse duration t(int) is met. It may be set by trigger signals
shorter than t(int).
8.10 Inputs – Interrupts DVIO Domain Ports P1 and P2
(P1.0 to P1.7, P2.0 to P2.7)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
t(int)
(1)
(2)
External interrupt timing(1)
TEST CONDITIONS
External trigger pulse duration to set interrupt flag,
VCC = 1.8 V or 3.0 V
VIO (2)
MIN
1.62 V to 1.98 V
20
MAX
UNIT
ns
An external signal sets the interrupt flag every time the minimum interrupt pulse duration t(int) is met. It may be set by trigger signals
shorter than t(int).
In all test conditions, VIO ≤ VCC.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
21
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.11 Leakage Current – General-Purpose I/O DVCC Domain
(P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Ilkg(Px.y)
(1)
(2)
TEST CONDITIONS
High-impedance leakage current
See
(1) (2)
VCC
MIN
MAX
1.8 V, 3 V
–50
50
UNIT
nA
The leakage current is measured with VSS or VCC applied to the corresponding pins, unless otherwise noted.
The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup or pulldown resistor is
disabled.
8.12 Leakage Current – General-Purpose I/O DVIO Domain
(P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P7.0 to P7.5)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Ilkg(Px.y)
(1)
(2)
(3)
High-impedance leakage current
VIO (1)
MIN
MAX
1.62 V to 1.98 V
–50
50
TEST CONDITIONS
See
(2) (3)
UNIT
nA
In all test conditions, VIO ≤ VCC.
The leakage current is measured with VSS or VIO applied to the corresponding pins, unless otherwise noted.
The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup or pulldown resistor is
disabled.
8.13 Outputs – General-Purpose I/O DVCC Domain (Full Drive Strength)
(P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
I(OHmax) = –3
VOH
High-level output voltage
mA(1)
I(OHmax) = –10 mA(2)
I(OHmax) = –5
mA(1)
I(OHmax) = –15 mA(2)
I(OLmax) = 3
VOL
Low-level output voltage
mA(1)
I(OLmax) = 10 mA(2)
I(OLmax) = 5 mA(1)
I(OLmax) = 15 mA(2)
(1)
(2)
22
VCC
1.8 V
3V
1.8 V
3V
MIN
MAX
VCC – 0.25
VCC
VCC – 0.60
VCC
VCC – 0.25
VCC
VCC – 0.60
VCC
VSS
VSS + 0.25
VSS
VSS + 0.60
VSS
VSS + 0.25
VSS
VSS + 0.60
UNIT
V
V
The maximum total current, I(OHmax) and I(OLmax), for all outputs combined should not exceed ±48 mA to hold the maximum voltage
drop specified.
The maximum total current, I(OHmax) and I(OLmax), for all outputs combined should not exceed ±100 mA to hold the maximum voltage
drop specified.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.14 Outputs – General-Purpose I/O DVCC Domain (Reduced Drive Strength)
(P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(3)
PARAMETER
TEST CONDITIONS
I(OHmax) = –1
VOH
High-level output voltage
mA(1)
I(OHmax) = –3 mA(2)
I(OHmax) = –2
mA(1)
I(OHmax) = –6 mA(2)
I(OLmax) = 1
VOL
Low-level output voltage
mA(1)
I(OLmax) = 3 mA(2)
I(OLmax) = 2
mA(1)
I(OLmax) = 6 mA(2)
(1)
(2)
(3)
VCC
1.8 V
3.0 V
MIN
MAX
VCC – 0.25
VCC
VCC – 0.60
VCC
VCC – 0.25
VCC
VCC – 0.60
VCC
VSS
VSS + 0.25
VSS
VSS + 0.60
VSS
VSS + 0.25
VSS
VSS + 0.60
1.8 V
3.0 V
UNIT
V
V
The maximum total current, I(OHmax) and I(OLmax), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage
drop specified.
The maximum total current, I(OHmax) and I(OLmax), for all outputs combined, should not exceed ±100 mA to hold the maximum voltage
drop specified.
Selecting reduced drive strength may reduce EMI.
8.15 Outputs – General-Purpose I/O DVIO Domain (Full Drive Strength)
(P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P7.0 to P7.5)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
I(OHmax) = –100
VOH
High-level output voltage
VOL
(1)
(2)
Low-level output voltage
µA(1)
I(OHmax) = –3 mA(1)
I(OHmax) = –6
VIO (2)
1.62 V to 1.98 V
mA(1)
I(OLmax) = 3 mA(1)
I(OLmax) = 6 mA(1)
MIN
MAX
VIO – 0.05
VIO
VIO – 0.25
VIO
VIO – 0.50
VIO
VSS
VSS + 0.25
VSS
VSS + 0.50
1.62 V to 1.98 V
UNIT
V
V
The maximum total current, I(OHmax) and I(OLmax), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage
drop specified.
In all test conditions, VIO ≤ VCC.
8.16 Outputs – General-Purpose I/O DVIO Domain (Reduced Drive Strength)
(P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P7.0 to P7.5)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(2)
PARAMETER
TEST CONDITIONS
I(OHmax) = –100
VOH
High-level output voltage
I(OHmax) = –1 mA(1)
I(OHmax) = –2
VOL
(1)
(2)
(3)
Low-level output voltage
VIO (3)
µA(1)
1.62 V to 1.98 V
mA(1)
I(OLmax) = 1 mA(1)
I(OLmax) = 2 mA(1)
1.62 V to 1.98 V
MIN
MAX
VIO – 0.05
VIO
VIO – 0.25
VIO
VIO – 0.50
VIO
VSS
VSS + 0.25
VSS
VSS + 0.50
UNIT
V
V
The maximum total current, I(OHmax) and I(OLmax), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage
drop specified.
Selecting reduced drive strength may reduce EMI.
In all test conditions, VIO ≤ VCC.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
23
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.17 Output Frequency – General-Purpose I/O DVCC Domain
(P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fPx.y
fPort_CLK
(1)
(2)
TEST CONDITIONS
Port output frequency
(with load)
See
Clock output frequency
ACLK, SMCLK, or MCLK,
CL = 20 pF(2)
(1) (2)
MIN
MAX
VCC = 1.8 V,
PMMCOREVx = 0
16
VCC = 3 V,
PMMCOREVx = 3
25
VCC = 1.8 V,
PMMCOREVx = 0
16
VCC = 3 V,
PMMCOREVx = 3
25
UNIT
MHz
MHz
A resistive divider with 2 × R1 between VCC and VSS is used as load. The output is connected to the center tap of the divider. For full
drive strength, R1 = 550 Ω. For reduced drive strength, R1 = 1.6 kΩ. CL = 20 pF is connected to the output to VSS.
The output voltage reaches at least 10% and 90% VCC at the specified toggle frequency.
8.18 Output Frequency – General-Purpose I/O DVIO Domain
(P1.0 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P7.0 to P7.5)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Port output frequency
(with load)
fPx.y
fPort_CLK
(1)
(2)
(3)
24
Clock output frequency
TEST CONDITIONS
See (1) (2)
ACLK, SMCLK, or MCLK,
CL = 20 pF(2)
MIN
MAX
VIO = 1.62 V to 1.98 V(3),
PMMCOREVx = 0
16
VIO = 1.62 V to 1.98 V(3),
PMMCOREVx = 3
25
VIO = 1.62 V to 1.98 V(3),
PMMCOREVx = 0
16
VIO = 1.62 V to 1.98 V(3),
PMMCOREVx = 3
25
UNIT
MHz
MHz
A resistive divider with 2 × R1 between VIO and VSS is used as load. The output is connected to the center tap of the divider. For full
drive strength, R1 = 550 Ω. For reduced drive strength, R1 = 1.6 kΩ. CL = 20 pF is connected to the output to VSS.
The output voltage reaches at least 10% and 90% VIO at the specified toggle frequency.
In all test conditions, VIO ≤ VCC.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.19 Typical Characteristics – Outputs, Reduced Drive Strength (PxDS.y = 0)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
8.0
VCC = 3.0 V
Px.y
IOL – Typical Low-Level Output Current – mA
IOL – Typical Low-Level Output Current – mA
25.0
TA = 25°C
20.0
TA = 85°C
15.0
10.0
5.0
0.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
7.0
5.0
4.0
3.0
2.0
1.0
VOL – Low-Level Output Voltage – V
IOH – Typical High-Level Output Current – mA
IOH – Typical High-Level Output Current – mA
0.0
VCC = 3.0 V
Px.y
−5.0
−10.0
−25.0
0.0
TA = 85°C
TA = 25°C
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VOH – High-Level Output Voltage – V
Figure 8-6. Typical High-Level Output Current vs
High-Level Output Voltage
Copyright © 2020 Texas Instruments Incorporated
1.0
1.5
2.0
Figure 8-5. Typical Low-Level Output Current vs
Low-Level Output Voltage
0.0
−20.0
0.5
VOL – Low-Level Output Voltage – V
Figure 8-4. Typical Low-Level Output Current vs
Low-Level Output Voltage
−15.0
TA = 85°C
6.0
0.0
0.0
3.5
TA = 25°C
VCC = 1.8 V
Px.y
−1.0
VCC = 1.8 V
Px.y
−2.0
−3.0
−4.0
−5.0
−6.0
TA = 85°C
TA = 25°C
−7.0
−8.0
0.0
0.5
1.0
1.5
VOH – High-Level Output Voltage – V
2.0
Figure 8-7. Typical High-Level Output Current vs
High-Level Output Voltage
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
25
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.20 Typical Characteristics – Outputs, Full Drive Strength (PxDS.y = 1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
55.0
24
TA = 25°C
VCC = 3.0 V
Px.y
50.0
IOL – Typical Low-Level Output Current – mA
IOL – Typical Low-Level Output Current – mA
60.0
TA = 85°C
45.0
40.0
35.0
30.0
25.0
20.0
15.0
10.0
5.0
0.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
12
8
4
IOH – Typical High-Level Output Current – mA
IOH – Typical High-Level Output Current – mA
1.5
2.0
0
VCC = 3.0 V
Px.y
−10.0
−15.0
−20.0
−25.0
−30.0
−35.0
−40.0
−45.0
TA = 85°C
−55.0
VCC = 1.8 V
Px.y
−4
−8
−12
TA = 85°C
−16
TA = 25°C
TA = 25°C
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VOH – High-Level Output Voltage – V
Figure 8-10. Typical High-Level Output Current vs
High-Level Output Voltage
26
1.0
Figure 8-9. Typical Low-Level Output Current vs
Low-Level Output Voltage
0.0
−60.0
0.0
0.5
VOL – Low-Level Output Voltage – V
Figure 8-8. Typical Low-Level Output Current vs
Low-Level Output Voltage
−50.0
TA = 85°C
16
VOL – Low-Level Output Voltage – V
−5.0
TA = 25°C
20
0
0.0
3.5
VCC = 1.8 V
Px.y
Submit Document Feedback
−20
0.0
0.5
1.0
1.5
2.0
VOH – High-Level Output Voltage – V
Figure 8-11. Typical High-Level Output Current vs
High-Level Output Voltage
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.21 Crystal Oscillator, XT1, Low-Frequency Mode
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1)
PARAMETER
TEST CONDITIONS
VCC
MIN
fOSC = 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 1,
TA = 25°C
ΔIDVCC.LF
Differential XT1 oscillator crystal
current consumption from lowest
drive setting, LF mode
fOSC = 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 2,
TA = 25°C
fXT1,LF,SW
XT1 oscillator logic-level squarewave input frequency, LF mode
XTS = 0, XT1BYPASS = 1(2) (3)
XT1BYPASSLV = 0 or 1
10
32.768
XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 0,
fXT1,LF = 32768 Hz, CL,eff = 6 pF
210
XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 1,
fXT1,LF = 32768 Hz, CL,eff = 12 pF
300
Integrated effective load
capacitance, LF mode(5)
fFault,LF
tSTART,LF
(1)
(2)
(3)
(4)
5.5
XTS = 0, XCAPx = 2
8.5
XTS = 0, XCAPx = 3
12.0
XTS = 0, Measured at ACLK,
fXT1,LF = 32768 Hz
Oscillator fault frequency,
LF mode(7)
XTS = 0,
XT1BYPASS = 1(8),
XT1BYPASSLV = 0 or 1
Start-up time, LF mode
fOSC = 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 0,
TA = 25°C, CL,eff = 6 pF
fOSC = 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 3,
TA = 25°C, CL,eff = 12 pF
50
kHz
1
XTS = 0, XCAPx = 1
Duty cycle, LF mode
Hz
kΩ
XTS = 0, XCAPx = 0(6)
CL,eff
UNIT
µA
0.170
32768
XTS = 0, XT1BYPASS = 0
OALF
3.0 V
0.290
XT1 oscillator crystal frequency,
LF mode
MAX
0.075
fOSC = 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 3,
TA = 25°C
fXT1,LF0
Oscillation allowance for
LF crystals(4)
TYP
pF
30%
70%
10
10000
Hz
1000
3.0 V
ms
500
To improve EMI on the XT1 oscillator, the following guidelines should be observed.
• Keep the trace between the device and the crystal as short as possible.
• Design a good ground plane around the oscillator pins.
• Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
• Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
• Use assembly materials and processes that avoid any parasitic load on the oscillator XIN and XOUT pins.
• If conformal coating is used, make sure that it does not induce capacitive or resistive leakage between the oscillator pins.
When XT1BYPASS is set, XT1 circuits are automatically powered down. Input signal is a digital square-wave with parametrics defined
in the Schmitt-Trigger Inputs section of this data sheet. When in crystal bypass mode, XIN can be configured so that it can support an
input digital waveform with swing levels from DVSS to DVCC (XT1BYPASSLV = 0) or DVSS to DVIO (XT1BYPASSLV = 1). In this
case, it is required that the pin be configured properly for the intended input swing.
Maximum frequency of operation of the entire device cannot be exceeded.
Oscillation allowance is based on a safety factor of 5 for recommended crystals. The oscillation allowance is a function of the
XT1DRIVEx settings and the effective load. In general, comparable oscillator allowance can be achieved based on the following
guidelines, but each application should be evaluated based on the actual crystal selected:
• For XT1DRIVEx = 0, CL,eff ≤ 6 pF
• For XT1DRIVEx = 1, 6 pF ≤ CL,eff ≤ 9 pF
• For XT1DRIVEx = 2, 6 pF ≤ CL,eff ≤ 10 pF
• For XT1DRIVEx = 3, CL,eff ≥ 6 pF
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
27
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
(5)
(6)
(7)
(8)
Includes parasitic bond and package capacitance (approximately 2 pF per pin).
Because the PCB adds additional capacitance, verify the correct load by measuring the ACLK frequency. For a correct setup, the
effective load capacitance should always match the specification of the used crystal.
Requires external capacitors at both terminals. Values are specified by crystal manufacturers.
Frequencies below the MIN specification set the fault flag. Frequencies above the MAX specification do not set the fault flag.
Frequencies between the MIN and MAX specifications might set the flag.
Measured with logic-level input frequency but also applies to operation with crystals.
8.22 Crystal Oscillator, XT2
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1) (2)
PARAMETER
TEST CONDITIONS
VCC
MIN
fOSC = 4 MHz, XT2OFF = 0, TA = 25°C,
XT2BYPASS = 0, XT2DRIVEx = 0,
IDVCC.XT2
XT2 oscillator crystal current
consumption
fOSC = 12 MHz, XT2OFF = 0, TA = 25°C,
XT2BYPASS = 0, XT2DRIVEx = 1,
fOSC = 20 MHz, XT2OFF = 0, TA = 25°C,
XT2BYPASS = 0, XT2DRIVEx = 2,
TYP
MAX
UNIT
200
260
3.0 V
µA
325
fOSC = 32 MHz, XT2OFF = 0, TA = 25°C,
XT2BYPASS = 0, XT2DRIVEx = 3,
450
fXT2,HF0
XT2 oscillator crystal
frequency, mode 0
XT2DRIVEx = 0, XT2BYPASS = 0(3)
4
8
MHz
fXT2,HF1
XT2 oscillator crystal
frequency, mode 1
XT2DRIVEx = 1, XT2BYPASS = 0(3)
8
16
MHz
fXT2,HF2
XT2 oscillator crystal
frequency, mode 2
XT2DRIVEx = 2, XT2BYPASS = 0(3)
16
24
MHz
fXT2,HF3
XT2 oscillator crystal
frequency, mode 3
XT2DRIVEx = 3, XT2BYPASS = 0(3)
24
32
MHz
fXT2,HF,SW
XT2 oscillator logic-level
XT2BYPASS = 1(4) (3)
square-wave input frequency,
XT2BYPASSLV = 0 or 1
bypass mode
0.7
32
MHz
Oscillation allowance for
HF crystals(5)
OAHF
tSTART,HF
Start-up time
Duty cycle
fFault,HF
28
450
XT2DRIVEx = 1, XT2BYPASS = 0,
fXT2,HF1 = 12 MHz, CL,eff = 15 pF
320
XT2DRIVEx = 2, XT2BYPASS = 0,
fXT2,HF2 = 20 MHz, CL,eff = 15 pF
200
XT2DRIVEx = 3, XT2BYPASS = 0,
fXT2,HF3 = 32 MHz, CL,eff = 15 pF
200
fOSC = 6 MHz,
XT2BYPASS = 0, XT2DRIVEx = 0,
TA = 25°C, CL,eff = 15 pF
0.5
fOSC = 20 MHz,
XT2BYPASS = 0, XT2DRIVEx = 2,
TA = 25°C, CL,eff = 15 pF
Ω
3.0 V
ms
0.3
Integrated effective load
capacitance, HF mode(6) (1)
CL,eff
(1)
(2)
XT2DRIVEx = 0, XT2BYPASS = 0,
fXT2,HF0 = 6 MHz, CL,eff = 15 pF
Oscillator fault frequency(7)
1
Measured at ACLK, fXT2,HF2 = 20 MHz
1(8),
XT2BYPASS =
XT2BYPASSLV = 0 or 1
40%
50%
30
pF
60%
300
kHz
Requires external capacitors at both terminals. Values are specified by crystal manufacturers.
To improve EMI on the XT2 oscillator the following guidelines should be observed.
• Keep the traces between the device and the crystal as short as possible.
• Design a good ground plane around the oscillator pins.
• Prevent crosstalk from other clock or data lines into oscillator pins XT2IN and XT2OUT.
• Avoid running PCB traces underneath or adjacent to the XT2IN and XT2OUT pins.
• Use assembly materials and processes that avoid any parasitic load on the oscillator XT2IN and XT2OUT pins.
• If conformal coating is used, make sure that it does not induce capacitive or resistive leakage between the oscillator pins.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
(3)
(4)
(5)
(6)
(7)
(8)
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
This represents the maximum frequency that can be input to the device externally. Maximum frequency achievable on the device
operation is based on the frequencies present on ACLK, MCLK, and SMCLK cannot be exceed for a given range of operation.
When XT2BYPASS is set, the XT2 circuit is automatically powered down. Input signal is a digital square-wave with parametrics defined
in the Schmitt-trigger Inputs section of this data sheet. When in crystal bypass mode, XT2IN can be configured so that it can support
an input digital waveform with swing levels from DVSS to DVCC (XT2BYPASSLV = 0) or DVSS to DVIO (XT2BYPASSLV = 1). In this
case, it is required that the pin be configured properly for the intended input swing.
Oscillation allowance is based on a safety factor of 5 for recommended crystals.
Includes parasitic bond and package capacitance (approximately 2 pF per pin).
Because the PCB adds additional capacitance, verify the correct load by measuring the ACLK frequency. For a correct setup, the
effective load capacitance should always match the specification of the used crystal.
Frequencies below the MIN specification set the fault flag. Frequencies above the MAX specification do not set the fault flag.
Frequencies between the MIN and MAX specifications might set the flag.
Measured with logic-level input frequency but also applies to operation with crystals. Typically, an effective load capacitance of up to 18
pF can be supported.
8.23 Internal Very-Low-Power Low-Frequency Oscillator (VLO)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fVLO
VLO frequency
dfVLO/dT
VLO frequency temperature drift
dfVLO/dVCC VLO frequency supply voltage drift
Duty cycle
(1)
(2)
TEST CONDITIONS
Measured at ACLK
VCC
1.8 V to 3.6 V
MIN
TYP
MAX
6
9.4
14
UNIT
kHz
ACLK(1)
1.8 V to 3.6 V
0.5
%/°C
Measured at ACLK(2)
1.8 V to 3.6 V
4
%/V
Measured at ACLK
1.8 V to 3.6 V
Measured at
40%
50%
60%
Calculated using the box method: (MAX(–40°C to 85°C) – MIN(–40°C to 85°C)) / MIN(–40°C to 85°C) / (85°C – (–40°C))
Calculated using the box method: (MAX(1.8 V to 3.6 V) – MIN(1.8 V to 3.6 V)) / MIN(1.8 V to 3.6 V) / (3.6 V – 1.8 V)
8.24 Internal Reference, Low-Frequency Oscillator (REFO)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
IREFO
fREFO
dfREFO/dVCC
tSTART
(1)
(2)
VCC
MIN
TA = 25°C
1.8 V to 3.6 V
REFO frequency calibrated
Measured at ACLK
1.8 V to 3.6 V
Full temperature range
1.8 V to 3.6 V
–3.5%
3V
–1.5%
REFO absolute tolerance calibrated
dfREFO/dT
TEST CONDITIONS
REFO oscillator current consumption
REFO frequency temperature drift
TA = 25°C
Measured at ACLK(1)
1.8 V to 3.6 V
ACLK(2)
1.8 V to 3.6 V
REFO frequency supply voltage drift
Measured at
Duty cycle
Measured at ACLK
1.8 V to 3.6 V
REFO start-up time
40%/60% duty cycle
1.8 V to 3.6 V
TYP
MAX
3
µA
32768
Hz
3.5%
1.5%
0.01
%/°C
1.0
40%
UNIT
50%
25
%/V
60%
µs
Calculated using the box method: (MAX(–40°C to 85°C) – MIN(–40°C to 85°C)) / MIN(–40°C to 85°C) / (85°C – (–40°C))
Calculated using the box method: (MAX(1.8 V to 3.6 V) – MIN(1.8 V to 3.6 V)) / MIN(1.8 V to 3.6 V) / (3.6 V – 1.8 V)
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
29
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.25 DCO Frequency
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
0)(1)
MIN
TYP
MAX
UNIT
fDCO(0,0)
DCO frequency (0,
DCORSELx = 0, DCOx = 0, MODx = 0
0.07
0.20
MHz
fDCO(0,31)
DCO frequency (0, 31)(1)
DCORSELx = 0, DCOx = 31, MODx = 0
0.70
1.70
MHz
fDCO(1,0)
DCO frequency (1, 0)(1)
DCORSELx = 1, DCOx = 0, MODx = 0
0.15
0.36
MHz
fDCO(1,31)
DCO frequency (1, 31)(1)
DCORSELx = 1, DCOx = 31, MODx = 0
1.47
3.45
MHz
fDCO(2,0)
DCO frequency (2, 0)(1)
DCORSELx = 2, DCOx = 0, MODx = 0
0.32
0.75
MHz
fDCO(2,31)
DCO frequency (2, 31)(1)
DCORSELx = 2, DCOx = 31, MODx = 0
3.17
7.38
MHz
fDCO(3,0)
DCO frequency (3, 0)(1)
DCORSELx = 3, DCOx = 0, MODx = 0
0.64
1.51
MHz
fDCO(3,31)
DCO frequency (3, 31)(1)
DCORSELx = 3, DCOx = 31, MODx = 0
6.07
14.0
MHz
fDCO(4,0)
DCO frequency (4, 0)(1)
DCORSELx = 4, DCOx = 0, MODx = 0
1.3
3.2
MHz
fDCO(4,31)
DCO frequency (4, 31)(1)
DCORSELx = 4, DCOx = 31, MODx = 0
12.3
28.2
MHz
fDCO(5,0)
DCO frequency (5, 0)(1)
DCORSELx = 5, DCOx = 0, MODx = 0
2.5
6.0
MHz
DCORSELx = 5, DCOx = 31, MODx = 0
23.7
54.1
MHz
DCORSELx = 6, DCOx = 0, MODx = 0
4.6
10.7
MHz
DCORSELx = 6, DCOx = 31, MODx = 0
39.0
88.0
MHz
DCORSELx = 7, DCOx = 0, MODx = 0
8.5
19.6
MHz
31)(1)
fDCO(5,31)
DCO frequency (5,
fDCO(6,0)
DCO frequency (6, 0)(1)
31)(1)
fDCO(6,31)
DCO frequency (6,
fDCO(7,0)
DCO frequency (7, 0)(1)
31)(1)
fDCO(7,31)
DCO frequency (7,
DCORSELx = 7, DCOx = 31, MODx = 0
60
135
MHz
SDCORSEL
Frequency step between range
DCORSEL and DCORSEL + 1
SRSEL = fDCO(DCORSEL+1,DCO)/fDCO(DCORSEL,DCO)
1.2
2.3
ratio
SDCO
Frequency step between tap DCO
and DCO + 1
SDCO = fDCO(DCORSEL,DCO+1)/fDCO(DCORSEL,DCO)
1.02
1.12
ratio
Duty cycle
Measured at SMCLK
40%
drift(2)
dfDCO/dT
DCO frequency temperature
dfDCO/dVCC
DCO frequency voltage drift(3)
(1)
(2)
(3)
50%
60%
fDCO = 1 MHz
0.1
%/°C
fDCO = 1 MHz
1.9
%/V
When selecting the proper DCO frequency range (DCORSELx), the target DCO frequency, fDCO, should be set to reside within the
range of fDCO(n, 0),MAX ≤ fDCO ≤ fDCO(n, 31),MIN, where fDCO(n, 0),MAX represents the maximum frequency specified for the DCO frequency,
range n, tap 0 (DCOx = 0) and fDCO(n,31),MIN represents the minimum frequency specified for the DCO frequency, range n, tap 31
(DCOx = 31). This ensures that the target DCO frequency resides within the range selected. It should also be noted that if the actual f
DCO frequency for the selected range causes the FLL or the application to select tap 0 or 31, the DCO fault flag is set to report that the
selected range is at its minimum or maximum tap setting.
Calculated using the box method: (MAX(–40°C to 85°C) – MIN(–40°C to 85°C)) / MIN(–40°C to 85°C) / (85°C – (–40°C))
Calculated using the box method: (MAX(1.8 V to 3.6 V) – MIN(1.8 V to 3.6 V)) / MIN(1.8 V to 3.6 V) / (3.6 V – 1.8 V)
100
VCC = 3.0 V
TA = 25°C
fDCO – MHz
10
DCOx = 31
1
0.1
DCOx = 0
0
1
2
3
4
5
6
7
DCORSEL
Figure 8-12. Typical DCO Frequency
30
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.26 PMM, Brownout Reset (BOR)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VDVCC_BOR_IT–
BORH on voltage, DVCC falling level
| dDVCC/dt | < 3 V/s
VDVCC_BOR_IT+
BORH off voltage, DVCC rising level
| dDVCC/dt | < 3 V/s
VDVCC_BOR_hys
BORH hysteresis
tRESET
Pulse duration required at RST/NMI pin to accept a reset
MIN
TYP
MAX UNIT
1.45
V
0.80
1.30
1.50
V
250
mV
50
2
µs
8.27 PMM, Core Voltage
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VCORE3(AM)
Core voltage, active mode, PMMCOREV = 3
2.4 V ≤ DVCC ≤ 3.6 V
1.90
V
VCORE2(AM)
Core voltage, active mode, PMMCOREV = 2
2.2 V ≤ DVCC ≤ 3.6 V
1.80
V
VCORE1(AM)
Core voltage, active mode, PMMCOREV = 1
2.0 V ≤ DVCC ≤ 3.6 V
1.60
V
VCORE0(AM)
Core voltage, active mode, PMMCOREV = 0
1.8 V ≤ DVCC ≤ 3.6 V
1.40
V
VCORE3(LPM)
Core voltage, low-current mode, PMMCOREV = 3
2.4 V ≤ DVCC ≤ 3.6 V
1.94
V
VCORE2(LPM)
Core voltage, low-current mode, PMMCOREV = 2
2.2 V ≤ DVCC ≤ 3.6 V
1.84
V
VCORE1(LPM)
Core voltage, low-current mode, PMMCOREV = 1
2.0 V ≤ DVCC ≤ 3.6 V
1.64
V
VCORE0(LPM)
Core voltage, low-current mode, PMMCOREV = 0
1.8 V ≤ DVCC ≤ 3.6 V
1.44
V
8.28 PMM, SVS High Side
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
SVSHE = 0, DVCC = 3.6 V
I(SVSH)
SVS current consumption
V(SVSH_IT–) SVSH on voltage level(1)
V(SVSH_IT+) SVSH off voltage level(1)
tpd(SVSH)
SVSH propagation delay
t(SVSH)
SVSH on or off delay time
dVDVCC/dt
DVCC rise time
(1)
MAX
0
SVSHE = 1, DVCC = 3.6 V, SVSHFP = 0
200
SVSHE = 1, DVCC = 3.6 V, SVSHFP = 1
1.5
nA
µA
SVSHE = 1, SVSHRVL = 0
1.57
1.68
1.78
SVSHE = 1, SVSHRVL = 1
1.79
1.88
1.98
SVSHE = 1, SVSHRVL = 2
1.98
2.08
2.21
SVSHE = 1, SVSHRVL = 3
2.10
2.18
2.31
SVSHE = 1, SVSMHRRL = 0
1.62
1.74
1.85
SVSHE = 1, SVSMHRRL = 1
1.88
1.94
2.07
SVSHE = 1, SVSMHRRL = 2
2.07
2.14
2.28
SVSHE = 1, SVSMHRRL = 3
2.20
2.30
2.42
SVSHE = 1, SVSMHRRL = 4
2.32
2.40
2.55
SVSHE = 1, SVSMHRRL = 5
2.52
2.70
2.88
SVSHE = 1, SVSMHRRL = 6
2.90
3.10
3.23
SVSHE = 1, SVSMHRRL = 7
2.90
3.10
3.23
SVSHE = 1, dVDVCC/dt = 10 mV/µs, SVSHFP = 1
2.5
SVSHE = 1, dVDVCC/dt = 1 mV/µs, SVSHFP = 0
20
SVSHE = 0 → 1, dVDVCC/dt = 10 mV/µs, SVSHFP = 1
12.5
SVSHE = 0 → 1, dVDVCC/dt = 1 mV/µs, SVSHFP = 0
100
0
UNIT
V
V
µs
µs
1000
V/s
The SVSH settings available depend on the VCORE (PMMCOREVx) setting. See the Power Management Module and Supply Voltage
Supervisor chapter in the MSP430x5xx and MSP430x6xx Family User's Guide on recommended settings and use.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
31
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.29 PMM, SVM High Side
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
SVMHE = 0, DVCC = 3.6 V
I(SVMH)
SVMH current consumption
0
SVMHE= 1, DVCC = 3.6 V, SVMHFP = 0
SVMH on or off voltage level(1)
1.5
tpd(SVMH)
SVMH propagation delay
t(SVMH)
SVMH on or off delay time
(1)
µA
SVMHE = 1, SVSMHRRL = 0
1.62
1.74
1.85
SVMHE = 1, SVSMHRRL = 1
1.88
1.94
2.07
SVMHE = 1, SVSMHRRL = 2
2.07
2.14
2.28
SVMHE = 1, SVSMHRRL = 3
2.20
2.30
2.42
SVMHE = 1, SVSMHRRL = 4
2.32
2.40
2.55
SVMHE = 1, SVSMHRRL = 5
2.52
2.70
2.88
SVMHE = 1, SVSMHRRL = 6
2.90
3.10
3.23
SVMHE = 1, SVSMHRRL = 7
2.90
3.10
3.23
SVMHE = 1, SVMHOVPE = 1
UNIT
nA
200
SVMHE = 1, DVCC = 3.6 V, SVMHFP = 1
V(SVMH)
MAX
V
3.75
SVMHE = 1, dVDVCC/dt = 10 mV/µs, SVMHFP = 1
2.5
SVMHE = 1, dVDVCC/dt = 1 mV/µs, SVMHFP = 0
20
SVMHE = 0 → 1, dVDVCC/dt = 10 mV/µs, SVMHFP = 1
12.5
SVMHE = 0 → 1, dVDVCC/dt = 1 mV/µs, SVMHFP = 0
100
µs
µs
The SVMH settings available depend on the VCORE (PMMCOREVx) setting. See the Power Management Module and Supply Voltage
Supervisor chapter in the MSP430x5xx and MSP430x6xx Family User's Guide on recommended settings and use.
8.30 PMM, SVS Low Side
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
SVSLE = 0, PMMCOREV = 2
I(SVSL)
SVSL current consumption
tpd(SVSL)
SVSL propagation delay
t(SVSL)
SVSL on or off delay time
32
Submit Document Feedback
0
SVSLE = 1, PMMCOREV = 2, SVSLFP = 0
200
SVSLE = 1, PMMCOREV = 2, SVSLFP = 1
1.5
SVSLE = 1, dVCORE/dt = 10 mV/µs, SVSLFP = 1
2.5
SVSLE = 1, dVCORE/dt = 1 mV/µs, SVSLFP = 0
20
SVSLE = 0 → 1, dVCORE/dt = 10 mV/µs, SVSLFP = 1
12.5
SVSLE = 0 → 1, dVCORE/dt = 1 mV/µs, SVSLFP = 0
100
MAX
UNIT
nA
µA
µs
µs
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.31 PMM, SVM Low Side
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
SVMLE = 0, PMMCOREV = 2
I(SVML)
SVML current consumption
tpd(SVML)
SVML propagation delay
t(SVML)
SVML on or off delay time
MAX
0
SVMLE= 1, PMMCOREV = 2, SVMLFP = 0
200
SVMLE= 1, PMMCOREV = 2, SVMLFP = 1
1.5
SVMLE = 1, dVCORE/dt = 10 mV/µs, SVMLFP = 1
2.5
SVMLE = 1, dVCORE/dt = 1 mV/µs, SVMLFP = 0
20
SVMLE = 0 → 1, dVCORE/dt = 10 mV/µs, SVMLFP = 1
12.5
SVMLE = 0 → 1, dVCORE/dt = 1 mV/µs, SVMLFP = 0
100
UNIT
nA
µA
µs
µs
8.32 Wake-up Times From Low-Power Modes and Reset
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TYP
MAX
fMCLK ≥ 4.0 MHz
MIN
3.5
7.5
UNIT
1.0 MHz < fMCLK <
4.0 MHz
4.5
9
150
175
µs
tWAKE-UP-FAST
Wake-up time from LPM2,
LPM3, or LPM4 to active
mode(1)
PMMCOREV = SVSMLRRL = n
(where n = 0, 1, 2, or 3),
SVSLFP = 1
tWAKE-UP-SLOW
Wake-up time from LPM2,
LPM3 or LPM4 to active
mode(2) (3)
PMMCOREV = SVSMLRRL = n
(where n = 0, 1, 2, or 3),
SVSLFP = 0
tWAKE-UP-LPM5
Wake-up time from LPM4.5
to active mode(4)
2
3
ms
tWAKE-UP-RESET
Wake-up time from RST or
BOR event to active mode(4)
2
3
ms
(1)
(2)
(3)
(4)
µs
This value represents the time from the wake-up event to the first active edge of MCLK. The wake-up time depends on the
performance mode of the low-side supervisor (SVSL) and low-side monitor (SVML). tWAKE-UP-FAST is possible with SVSL and SVML in
full performance mode or disabled. For specific register settings, see the Low-Side SVS and SVM Control and Performance Mode
Selection section in the Power Management Module and Supply Voltage Supervisor chapter of the MSP430x5xx and MSP430x6xx
Family User's Guide.
This value represents the time from the wake-up event to the first active edge of MCLK. The wake-up time depends on the
performance mode of the low-side supervisor (SVSL) and low-side monitor (SVML). tWAKE-UP-SLOW is set with SVSL and SVML in
normal mode (low current mode). For specific register settings, see the Low-Side SVS and SVM Control and Performance Mode
Selection section in the Power Management Module and Supply Voltage Supervisor chapter of the MSP430x5xx and MSP430x6xx
Family User's Guide.
The wake-up times from LPM0 and LPM1 to AM are not specified. They are proportional to MCLK cycle time but are not affected by
the performance mode settings as for LPM2, LPM3, and LPM4.
This value represents the time from the wake-up event to the reset vector execution.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
33
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.33 Timer_A
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
VIO
MIN
MAX UNIT
1.62 V to 1.8 V
25
Timer_A input clock frequency
Internal: SMCLK or ACLK,
External: TACLK,
Duty cycle = 50% ±10%
1.8 V
fTA
3.0 V
1.62 V to 1.98 V
25
Timer_A capture timing(1)
All capture inputs, minimum
pulse duration required for
capture
1.8 V
1.62 V to 1.8 V
20
tTA,cap
3.0 V
1.62 V to 1.98 V
20
(1)
MHz
ns
The external signal sets the interrupt flag every time the minimum parameters are met. It may be set even with trigger signals shorter
than tTA,cap.
8.34 Timer_B
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
VIO
MIN
MAX UNIT
1.62 V to 1.8 V
25
Timer_B input clock frequency
Internal: SMCLK or ACLK,
External: TBCLK,
Duty cycle = 50% ±10%
1.8 V
fTB
3.0 V
1.62 V to 1.98 V
25
Timer_B capture timing(1)
All capture inputs, minimum
pulse duration required for
capture
1.8 V
1.62 V to 1.8 V
20
tTB,cap
3.0 V
1.62 V to 1.98 V
20
(1)
34
MHz
ns
The external signal sets the interrupt flag every time the minimum parameters are met. It may be set even with trigger signals shorter
than tTB,cap.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.35 USCI (UART Mode) Clock Frequency
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
Internal: SMCLK or ACLK,
External: UCLK,
Duty cycle = 50% ±10%
fUSCI
USCI input clock frequency
fBITCLK
BITCLK clock frequency (equals baud rate in MBaud)
MAX UNIT
fSYSTEM
MHz
1
MHz
8.36 USCI (UART Mode)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
UART receive deglitch time(1)
tτ
(1)
VCC
VIO
MIN
MAX
1.8 V
1.62 V to 1.80 V
50
600
3.0 V
1.62 V to 1.98 V
50
600
UNIT
ns
Pulses on the UART receive input (UCxRX) shorter than the UART receive deglitch time are suppressed. To make sure that pulses are
correctly recognized, their duration should exceed the maximum specification of the deglitch time.
8.37 USCI (SPI Master Mode) Clock Frequency
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fUSCI
USCI input clock frequency
CONDITIONS
MIN
Internal: SMCLK or ACLK, Duty cycle = 50% ±10%
MAX
UNIT
fSYSTEM
MHz
MAX
UNIT
fSYSTEM
MHz
8.38 USCI (SPI Master Mode)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1)
(see Figure 8-13 and Figure 8-14)
PARAMETER
fUSCI
USCI input clock frequency
TEST CONDITIONS
55
3.0 V
1.62 V to 1.98 V
55
2.4 V
1.62 V to 1.98 V
35
3.0 V
1.62 V to 1.98 V
35
1.8 V
1.62 V to 1.80 V
0
3.0 V
1.62 V to 1.98 V
0
2.4 V
1.62 V to 1.98 V
0
3.0 V
1.62 V to 1.98 V
0
UCLK edge to SIMO valid,
CL = 20 pF, PMMCOREV = 0
1.8 V
1.62 V to 1.80 V
20
3.0 V
1.62 V to 1.98 V
20
UCLK edge to SIMO valid,
CL = 20 pF, PMMCOREV = 3
2.4 V
1.62 V to 1.98 V
16
3.0 V
1.62 V to 1.98 V
16
1.8 V
1.62 V to 1.80 V
–10
3.0 V
1.62 V to 1.98 V
–10
2.4 V
1.62 V to 1.98 V
–10
3.0 V
1.62 V to 1.98 V
–10
PMMCOREV = 3
PMMCOREV = 0
SOMI input data hold time
PMMCOREV = 3
tVALID,MO
SIMO output data valid time(2)
CL = 20 pF, PMMCOREV = 0
tHD,MO
SIMO output data hold time(3)
CL = 20 pF, PMMCOREV = 3
(1)
(2)
MIN
1.62 V to 1.80 V
SOMI input data setup time
tHD,MI
VIO
1.8 V
PMMCOREV = 0
tSU,MI
VCC
SMCLK or ACLK,
Duty cycle = 50% ±10%
ns
ns
ns
ns
fUCxCLK = 1/2tLO/HI with tLO/HI ≥ max(tVALID,MO(USCI) + tSU,SI(Slave), tSU,MI(USCI) + tVALID,SO(Slave))
For the slave parameters tSU,SI(Slave) and tVALID,SO(Slave), see the SPI parameters of the attached slave.
Specifies the time to drive the next valid data to the SIMO output after the output changing UCLK clock edge. See the timing diagrams
in Figure 8-13 and Figure 8-14.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
35
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
(3)
Specifies how long data on the SIMO output is valid after the output changing UCLK clock edge. Negative values indicate that the data
on the SIMO output can become invalid before the output changing clock edge observed on UCLK. See the timing diagrams in Figure
8-13 and Figure 8-14.
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLO/HI
tLO/HI
tSU,MI
tHD,MI
SOMI
tHD,MO
tVALID,MO
SIMO
Figure 8-13. SPI Master Mode, CKPH = 0
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLO/HI
tLO/HI
tSU,MI
tHD,MI
SOMI
tHD,MO
tVALID,MO
SIMO
Figure 8-14. SPI Master Mode, CKPH = 1
36
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.39 USCI (SPI Slave Mode)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1)
(see Figure 8-15 and Figure 8-16)
PARAMETER
TEST CONDITIONS
PMMCOREV = 0
tSTE,LEAD
STE lead time, STE low to clock
PMMCOREV = 3
PMMCOREV = 0
tSTE,LAG
STE lag time, Last clock to STE high
PMMCOREV = 3
PMMCOREV = 0
tSTE,ACC
STE access time, STE low to SOMI
data out
PMMCOREV = 3
PMMCOREV = 0
tSTE,DIS
STE disable time, STE high to SOMI
high impedance
PMMCOREV = 3
PMMCOREV = 0
tSU,SI
SIMO input data setup time
PMMCOREV = 3
PMMCOREV = 0
tHD,SI
SIMO input data hold time
PMMCOREV = 3
tVALID,SO
tHD,SO
(1)
(2)
(3)
SOMI output data valid time(2)
SOMI output data hold time(3)
VCC
VIO
1.8 V
1.62 V to 1.80 V
MIN
12
MAX
3.0 V
1.62 V to 1.98 V
12
2.4 V
1.62 V to 1.98 V
10
3.0 V
1.62 V to 1.98 V
10
1.8 V
1.62 V to 1.80 V
6
3.0 V
1.62 V to 1.98 V
6
2.4 V
1.62 V to 1.98 V
6
3.0 V
1.62 V to 1.98 V
6
1.8 V
1.62 V to 1.80 V
65
3.0 V
1.62 V to 1.98 V
65
2.4 V
1.62 V to 1.98 V
45
ns
ns
3.0 V
1.62 V to 1.98 V
45
1.8 V
1.62 V to 1.80 V
35
3.0 V
1.62 V to 1.98 V
35
2.4 V
1.62 V to 1.98 V
25
3.0 V
1.62 V to 1.98 V
1.8 V
1.62 V to 1.80 V
5
3.0 V
1.62 V to 1.98 V
5
2.4 V
1.62 V to 1.98 V
5
UNIT
ns
ns
25
3.0 V
1.62 V to 1.98 V
5
1.8 V
1.62 V to 1.80 V
5
3.0 V
1.62 V to 1.98 V
5
2.4 V
1.62 V to 1.98 V
5
5
ns
ns
3.0 V
1.62 V to 1.98 V
UCLK edge to SOMI valid,
CL = 20 pF,
PMMCOREV = 0
1.8 V
1.62 V to 1.80 V
75
3.0 V
1.62 V to 1.98 V
75
UCLK edge to SOMI valid,
CL = 20 pF,
PMMCOREV = 3
2.4 V
1.62 V to 1.98 V
50
3.0 V
1.62 V to 1.98 V
50
CL = 20 pF,
PMMCOREV = 0
1.8 V
1.62 V to 1.80 V
10
3.0 V
1.62 V to 1.98 V
10
CL = 20 pF,
PMMCOREV = 3
2.4 V
1.62 V to 1.98 V
10
3.0 V
1.62 V to 1.98 V
10
ns
ns
fUCxCLK = 1/2tLO/HI with tLO/HI ≥ max(tVALID,MO(Master) + tSU,SI(USCI), tSU,MI(Master) + tVALID,SO(USCI))
For the master parameters tSU,MI(Master) and tVALID,MO(Master), see the SPI parameters of the attached master.
Specifies the time to drive the next valid data to the SOMI output after the output changing UCLK clock edge. See the timing diagrams
in Figure 8-15 and Figure 8-16.
Specifies how long data on the SOMI output is valid after the output changing UCLK clock edge. See the timing diagrams in Figure
8-15 and Figure 8-16.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
37
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
tSTE,LEAD
tSTE,LAG
STE
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLO/HI
tSU,SI
tLO/HI
tHD,SI
SIMO
tHD,SO
tVALID,SO
tSTE,ACC
tSTE,DIS
SOMI
Figure 8-15. SPI Slave Mode, CKPH = 0
tSTE,LAG
tSTE,LEAD
STE
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLO/HI
tLO/HI
tHD,SI
tSU,SI
SIMO
tSTE,ACC
tHD,MO
tVALID,SO
tSTE,DIS
SOMI
Figure 8-16. SPI Slave Mode, CKPH = 1
38
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.40 USCI (I2C Mode)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 8-17)
PARAMETER
TEST CONDITIONS
fUSCI
USCI input clock frequency
fSCL
SCL clock frequency
2.2 V, 3 V
Hold time (repeated) START
tSU,STA
Setup time for a repeated START
tHD,DAT
Data hold time
tSU,DAT
Data setup time
Setup time for STOP
tSP
Pulse duration of spikes
suppressed by input filter
(1)
MIN
Internal: SMCLK or ACLK,
External: UCLK,
Duty cycle = 50% ±10%
tHD,STA
tSU,STO
VIO (1)
VCC
fSCL ≤ 100 kHz
fSCL > 100 kHz
fSCL ≤ 100 kHz
fSCL > 100 kHz
fSCL ≤ 100 kHz
fSCL > 100 kHz
1.62 V to 1.98 V
0
MAX UNIT
fSYSTEM
MHz
400
kHz
4.0
2.2 V, 3 V
1.62 V to 1.98 V
2.2 V, 3 V
1.62 V to 1.98 V
2.2 V, 3 V
1.62 V to 1.98 V
0
ns
2.2 V, 3 V
1.62 V to 1.98 V
250
ns
2.2 V, 3 V
1.62 V to 1.98 V
2.2 V, 3 V
1.62 V to 1.98 V
µs
0.6
4.7
µs
0.6
4.0
µs
0.6
50
600
ns
In all test conditions, VIO ≤ VCC
tSU,STA
tHD,STA
tHD,STA
tBUF
SDA
tLOW
tHIGH
tSP
SCL
tSU,DAT
tSU,STO
tHD,DAT
Figure 8-17. I2C Mode Timing
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
39
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.41 10-Bit ADC, Power Supply and Input Range Conditions
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1)
PARAMETER
TEST CONDITIONS
VCC
AVCC
Analog supply voltage
AVCC and DVCC are connected together,
AVSS and DVSS are connected together,
V(AVSS) = V(DVSS) = 0 V
V(Ax)
Analog input voltage range(2)
All ADC10_A pins: P1.0 to P1.5 and P3.6 and
P3.7 terminals
Operating supply current into fADC10CLK = 5.0 MHz, ADC10ON = 1,
AVCC terminal, REF module REFON = 0, SHT0 = 0, SHT1 = 0,
and reference buffer off
ADC10DIV = 0, ADC10SREF = 00
IADC10_A
TYP
MAX
UNIT
1.8
3.6
V
0
AVCC
V
2.2 V
60
100
3V
75
110
Operating supply current into fADC10CLK = 5.0 MHz, ADC10ON = 1,
AVCC terminal, REF module REFON = 1, SHT0 = 0, SHT1 = 0,
on, reference buffer on
ADC10DIV = 0, ADC10SREF = 01
3V
113
150
µA
f
= 5.0 MHz, ADC10ON = 1,
Operating supply current into ADC10CLK
REFON = 0, SHT0 = 0, SHT1 = 0,
AVCC terminal, REF module
ADC10DIV = 0, ADC10SREF = 10,
off, reference buffer on
VEREF = 2.5 V
3V
105
140
µA
f
= 5.0 MHz, ADC10ON = 1,
Operating supply current into ADC10CLK
REFON = 0, SHT0 = 0, SHT1 = 0,
AVCC terminal, REF module
ADC10DIV = 0, ADC10SREF = 11,
off, reference buffer off
VEREF = 2.5 V
3V
70
110
µA
2.2 V
3.5
CI
Input capacitance
RI
Input MUX ON resistance
(1)
(2)
MIN
Only one terminal Ax can be selected at one
time from the pad to the ADC10_A capacitor
array including wiring and pad
µA
pF
AVCC > 2 V, 0 V ≤ VAx ≤ AVCC
36
1.8 V < AVCC < 2 V, 0 V ≤ VAx ≤ AVCC
96
kΩ
The leakage current is defined in the leakage current table with P6.x/Ax parameter.
The analog input voltage range must be within the selected reference voltage range VR+ to VR– for valid conversion results. The
external reference voltage requires decoupling capacitors. See Section 8.44.
8.42 10-Bit ADC, Timing Parameters
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC
MIN
TYP
MAX
UNIT
For specified performance of ADC10_A
linearity parameters
2.2 V, 3 V
0.45
5
5.5
MHz
Internal ADC10_A
oscillator(3)
ADC10DIV = 0, fADC10CLK = fADC10OSC
2.2 V, 3 V
4.2
4.8
5.4
MHz
2.2 V, 3 V
2.4
Conversion time
REFON = 0, Internal oscillator,
12 ADC10CLK cycles, 10-bit mode
fADC10OSC = 4 MHz to 5 MHz
fADC10CLK
fADC10OSC
tCONVERT
TEST CONDITIONS
µs
External fADC10CLK from ACLK, MCLK or
SMCLK, ADC10SSEL ≠ 0
tADC10ON
Turnon settling time of
the ADC
See (1)
tSample
Sampling time
RS = 1000 Ω, RI = 96 k Ω, CI = 3.5 pF(2)
(1)
(2)
(3)
40
3.0
12 × 1 / f
ADC10CLK
100
ns
1.8 V
3
µs
3.0 V
1
µs
The condition is that the error in a conversion started after tADC10ON is less than ±0.5 LSB. The reference and input signal are already
settled.
Approximately 8 Tau (τ) are needed to get an error of less than ±0.5 LSB
The ADC10OSC is sourced directly from MODOSC inside the UCS.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.43 10-Bit ADC, Linearity Parameters
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
1.4 V ≤ (VeREF+ – VeREF–) ≤ 1.6 V, CVeREF+ = 20 pF
VCC
MIN
TYP
MAX
±1.0
UNIT
EI
Integral
linearity error
1.6 V < (VeREF+ – VeREF–) ≤ VAVCC, CVeREF+ = 20 pF
ED
Differential
linearity error
1.4 V ≤ (VeREF+ – VeREF–), CVeREF+ = 20 pF
2.2 V, 3 V
±1.0
LSB
EO
Offset error
1.4 V ≤ (VeREF+ – VeREF–), CVeREF+ = 20 pF,
Internal impedance of source RS < 100 Ω
2.2 V, 3 V
±1.0
LSB
EG
Gain error
1.4 V ≤ (VeREF+ – VeREF–), CVeREF+ = 20 pF,
ADC10SREFx = 11b
2.2 V, 3 V
±1.0
LSB
ET
Total unadjusted
error
1.4 V ≤ (VeREF+ – VeREF–), CVeREF+ = 20 pF,
ADC10SREFx = 11b
2.2 V, 3 V
±2.0
LSB
2.2 V, 3 V
±1.0
±1.0
LSB
8.44 REF, External Reference
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1)
PARAMETER
MIN
MAX
UNIT
VeREF+ > VeREF– (2)
1.4
AVCC
V
Negative external reference
voltage input
VeREF+ > VeREF– (3)
0
1.2
V
Differential external reference
voltage input
VeREF+ > VeREF– (4)
1.4
AVCC
V
VeREF+
Positive external reference
voltage input
VeREF–
(VeREF+ –
VeREF–)
IVeREF+,
IVeREF–
CVREF+,
CVREF(1)
(2)
(3)
(4)
(5)
Static input current
Capacitance at VeREF+ or
VeREF- terminal
TEST CONDITIONS
VCC
1.4 V ≤ VeREF+ ≤ VAVCC , VeREF– = 0 V,
fADC10CLK = 5 MHz, ADC10SHTx = 0x0001,
Conversion rate 200 ksps
2.2 V, 3 V
–26
26
µA
1.4 V ≤ VeREF+ ≤ VAVCC , VeREF– = 0 V,
fADC10CLK = 5 MHZ, ADC10SHTX = 0x1000,
Conversion rate 20 ksps
2.2 V, 3 V
–1
1
µA
See (5)
10
µF
The external reference is used during ADC conversion to charge and discharge the capacitance array. The input capacitance, CI, is
also the dynamic load for an external reference during conversion. The dynamic impedance of the reference supply should follow the
recommendations on analog-source impedance to allow the charge to settle for 10-bit accuracy.
The accuracy limits the minimum positive external reference voltage. Lower reference voltage levels may be applied with reduced
accuracy requirements.
The accuracy limits the maximum negative external reference voltage. Higher reference voltage levels may be applied with reduced
accuracy requirements.
The accuracy limits minimum external differential reference voltage. Lower differential reference voltage levels may be applied with
reduced accuracy requirements.
Two decoupling capacitors, 10 µF and 100 nF, should be connected to VREF to decouple the dynamic current required for an external
reference source if it is used for the ADC10_A. See also the MSP430x5xx and MSP430x6xx Family User's Guide.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
41
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.45 REF, Built-In Reference
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1)
PARAMETER
VREF+
AVCC(min)
Positive built-in reference
voltage
AVCC minimum voltage,
Positive built-in reference
active
Operating supply current
into AVCC terminal(1)
IREF+
TEST CONDITIONS
VCC
MIN
TYP
MAX
REFVSEL = {2} for 2.5 V
REFON = 1
3V
2.445
2.486
2.527
REFVSEL = {1} for 2.0 V
REFON = 1
3V
1.94
1.97
2.01
REFVSEL = {0} for 1.5 V
REFON = 1
2.2 V, 3 V
1.461
1.485
1.511
REFVSEL = {0} for 1.5 V
UNIT
V
1.8
REFVSEL = {1} for 2.0 V
2.2
REFVSEL = {2} for 2.5 V
2.7
V
fADC10CLK = 5.0 MHz
REFON = 1, REFBURST = 0,
REFVSEL = {2} for 2.5 V
3V
18
24
µA
fADC10CLK = 5.0 MHz
REFON = 1, REFBURST = 0,
REFVSEL = {1} for 2.0 V
3V
15.5
21
µA
fADC10CLK = 5.0 MHz
REFON = 1, REFBURST = 0,
REFVSEL = {0} for 1.5 V
3V
13.5
21
µA
30
50
ppm/
°C
TCREF+
Temperature coefficient of
built-in reference(2)
IVREF+ = 0 A
REFVSEL = {0, 1, 2}, REFON = 1
ISENSOR
Operating supply current
into AVCC terminal(4)
REFON = 0, INCH = 0Ah,
ADC10ON = N/A, TA = 30°C
2.2 V
20
22
3V
20
22
VSENSOR
See (5)
ADC10ON = 1, INCH = 0Ah,
TA = 30°C
2.2 V
770
3V
770
VMID
AVCC divider at channel 11
ADC10ON = 1, INCH = 0Bh,
VMID ≈ 0.5 × VAVCC
2.2 V
1.06
1.1
1.14
3V
1.46
1.5
1.54
tSENSOR(sample)
Sample time required if
channel 10 is selected(6)
ADC10ON = 1, INCH = 0Ah,
Error of conversion result ≤ 1 LSB
30
µs
tVMID(sample)
Sample time required if
channel 11 is selected(7)
ADC10ON = 1, INCH = 0Bh,
Error of conversion result ≤ 1 LSB
1
µs
PSRR_DC
Power supply rejection ratio AVCC = AVCC(min) to AVCC(max),
(DC)
TA = 25°C, REFVSEL = {0, 1, 2}, REFON = 1
120
µV/V
PSRR_AC
AVCC = AVCC(min) to AVCC(max),
Power supply rejection ratio
TA = 25°C, f = 1 kHz, ΔVpp = 100 mV,
(AC)
REFVSEL = {0, 1, 2}, REFON = 1
6.4
mV/V
tSETTLE
Settling time of reference
voltage(3)
75
µs
(1)
(2)
(3)
(4)
(5)
(6)
(7)
42
AVCC = AVCC(min) to AVCC(max),
REFVSEL = {0, 1, 2}, REFON = 0 → 1
µA
mV
V
The internal reference current is supplied from terminal AVCC. Consumption is independent of the ADC10ON control bit, unless a
conversion is active. The REFON bit enables to settle the built-in reference before starting an A/D conversion.
Calculated using the box method: (MAX(–40°C to 85°C) – MIN(–40°C to 85°C)) / MIN(–40°C to 85°C)/(85°C – (–40°C)).
The condition is that the error in a conversion started after tREFON is less than ±0.5 LSB.
The sensor current ISENSOR is consumed if (ADC10ON = 1 and REFON = 1) or (ADC10ON = 1 and INCH = 0Ah and sample signal is
high). When REFON = 1, ISENSOR is already included in IREF+.
The temperature sensor offset can be significant. TI recommends a single-point calibration to minimize the offset error of the built-in
temperature sensor.
The typical equivalent impedance of the sensor is 51 kΩ. The sample time required includes the sensor-on time tSENSOR(on).
The on-time tVMID(on) is included in the sampling time tVMID(sample); no additional on time is needed.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.46 Comparator_B
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC
TEST CONDITIONS
VCC
Supply voltage
MIN
TYP
1.8
3.6
1.8 V
IAVCC_COMP
VREF
IAVCC_REF
Comparator operating
supply current into AVCC,
Excludes reference
resistor ladder
Reference voltage level
Quiescent current of
resistor ladder into AVCC,
Includes REF module
current
VIC
Common mode input
range
VOFFSET
Input offset voltage
CIN
Input capacitance
RSIN
Series input resistance
tPD
Propagation delay,
response time
tPD,filter
tEN_CMP
Propagation delay with
filter active
Comparator enable time
tEN_REF
Resistor reference enable
time
TCREF
Temperature coefficient
reference
VCB_REF
Reference voltage for a
given tap
Copyright © 2020 Texas Instruments Incorporated
CBPWRMD = 00, CBON = 1,
CBRSx = 00
MAX
31
38
3V
32
39
CBPWRMD = 01, CBON = 1,
CBRSx = 00
2.2 V, 3 V
10
17
CBPWRMD = 10, CBON = 1,
CBRSx = 00
2.2 V, 3 V
0.2
0.85
µA
CBREFLx = 01, CBREFACC = 0
≥1.8V
1.400
1.43
1.472
CBREFLx = 10, CBREFACC = 0
≥2.2V
1.864
1.90
1.960
CBREFLx = 11, CBREFACC = 0
≥3.0V
2.32
2.37
2.44
CBREFACC = 0, CBREFLx = 01,
CBRSx = 10, REFON = 0, CBON = 0
2.2 V, 3 V
33
40
CBREFACC = 1, CBREFLx = 01,
CBRSx = 10, REFON = 0, CBON = 0
2.2 V, 3 V
17
22
VCC – 1
CBPWRMD = 00
–20
20
CBPWRMD = 01, 10
–10
10
5
On (switch closed)
3
V
mV
pF
4
50
kΩ
MΩ
CBPWRMD = 00, CBF = 0
450
CBPWRMD = 01, CBF = 0
600
CBPWRMD = 10, CBF = 0
50
CBPWRMD = 00, CBON = 1, CBF = 1,
CBFDLY = 00
0.35
0.6
1.5
CBPWRMD = 00, CBON = 1, CBF = 1,
CBFDLY = 01
0.6
1.0
1.8
CBPWRMD = 00, CBON = 1, CBF = 1,
CBFDLY = 10
1.0
1.8
3.4
CBPWRMD = 00, CBON = 1, CBF = 1,
CBFDLY = 11
1.8
3.4
6.5
1
2
ns
µs
µs
µs
CBON = 0 → 1,
CBPWRMD = 10
CBON = 0 → 1
V
µA
0
CBON = 0 → 1,
CBPWRMD = 00 or 01
V
38
2.2 V
Off (switch open)
UNIT
100
1.0
1.5
µs
50 ppm/ °C
VIN = reference into resistor ladder,
n = 0 to 31
VIN ×
VIN ×
VIN ×
(n + 0.5) / (n + 1) / (n + 1.5) /
32
32
32
V
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
43
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.47 Flash Memory
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TJ
DVCC(PGM/ERASE) Program and erase supply voltage
IPGM
MIN
TYP
1.8
MAX
3.6
UNIT
V
Average supply current from DVCC during program
3
5
IERASE
Average supply current from DVCC during erase
6
15
mA
IMERASE, IBANK
Average supply current from DVCC during mass erase or bank erase
6
15
mA
tCPT
Cumulative program time(1)
16
104
Program and erase endurance
tRetention
Data retention duration
tWord
Word or byte program time(2)
25°C
word(2)
105
mA
ms
cycles
100
years
64
85
µs
tBlock, 0
Block program time for first byte or
49
65
µs
tBlock, 1–(N–1)
Block program time for each additional byte or word, except for last byte
or word(2)
37
49
µs
tBlock, N
Block program time for last byte or word(2)
55
73
µs
tErase
Erase time for segment, mass erase, and bank erase when available(2)
23
32
ms
fMCLK,MGR
MCLK frequency in marginal read mode
(FCTL4.MGR0 = 1 or FCTL4.MGR1 = 1)
0
1
MHz
(1)
(2)
The cumulative program time must not be exceeded when writing to a 128-byte flash block. This parameter applies to all programming
methods: individual word or byte write mode and block write mode.
These values are hardwired into the state machine of the flash controller.
8.48 JTAG and Spy-Bi-Wire Interface
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
VCC
VIO
fSBW
Spy-Bi-Wire input frequency
PARAMETER
2.2 V, 3 V
1.62 V to 1.98 V
0
20
MHz
tSBW,Low
Spy-Bi-Wire low clock pulse duration
2.2 V, 3 V
1.62 V to 1.98 V
0.025
15
µs
tSBW, En
Spy-Bi-Wire enable time (TEST high to acceptance of first
clock edge)(1)
1
µs
tSBW,Rst
Spy-Bi-Wire return to normal operation time
µs
fTCK
TCK input frequency for 4-wire JTAG(2)
Rinternal
Internal pulldown resistance on TEST
(1)
(2)
44
MIN
TYP
1.62 V to 1.98 V
MAX UNIT
2.2 V, 3 V
1.62 V to 1.98 V
15
100
2.2 V
1.62 V to 1.98 V
0
5
3V
1.62 V to 1.98 V
0
10
2.2 V, 3 V
1.62 V to 1.98 V
45
60
80
MHz
kΩ
Tools that access the Spy-Bi-Wire interface must wait for the tSBW,En time after pulling the TEST/SBWTCK pin high before applying the
first SBWTCK clock edge.
fTCK may be restricted to meet the timing requirements of the module selected.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
8.49 DVIO BSL Entry
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 8-18)
PARAMETER
RST/NMI(1)
tSU, BSLEN
Setup time, BSLEN to
tHO, BSLEN
Hold time, BSLEN to RST/NMI(2)
(1)
(2)
VCC
VIO
MIN
MAX
UNIT
2.2 V, 3 V
1.62 V to 1.98 V
100
ns
2.2 V, 3 V
1.62 V to 1.98 V
350
µs
AVCC, DVCC, DVIO stable and within specification.
BSLEN must remain logic high long enough for the boot code to detect its level and enter the BSL sequence. After the minimum hold
time is achieved, BSLEN is a don't care.
BSLEN
VIT+
VITtHO,BSLEN
VIT+
VITRST/NMI
(DVIO domain)
t
tSU,BSLEN
Figure 8-18. DVIO BSL Entry Timing
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
45
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9 Detailed Description
9.1 CPU
The MSP430 CPU has a 16-bit RISC architecture that is highly transparent to the application. All operations,
other than program-flow instructions, are performed as register operations in conjunction with seven addressing
modes for source operand and four addressing modes for destination operand.
The CPU is integrated with 16 registers that provide reduced instruction execution time. The register-to-register
operation execution time is one cycle of the CPU clock. Four of the registers, R0 to R3, are dedicated as
program counter, stack pointer, status register, and constant generator, respectively. The remaining registers are
general-purpose registers (see Figure 9-1).
Peripherals are connected to the CPU using data, address, and control buses. Peripherals can be managed with
all instructions.
The instruction set consists of the original 51 instructions with three formats and seven address modes and
additional instructions for the expanded address range. Each instruction can operate on word and byte data.
Program Counter
PC/R0
Stack Pointer
SP/R1
Status Register
Constant Generator
SR/CG1/R2
CG2/R3
General-Purpose Register
R4
General-Purpose Register
R5
General-Purpose Register
R6
General-Purpose Register
R7
General-Purpose Register
R8
General-Purpose Register
R9
General-Purpose Register
R10
General-Purpose Register
R11
General-Purpose Register
R12
General-Purpose Register
R13
General-Purpose Register
R14
General-Purpose Register
R15
Figure 9-1. Integrated CPU Registers
46
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.2 Operating Modes
These MCUs have one active mode and six software-selectable low-power modes of operation. An interrupt
event can wake up the device from any of the low-power modes, service the request, and restore back to the
low-power mode on return from the interrupt program.
Software can configure the following seven operating modes:
•
•
•
•
•
•
•
Active mode (AM)
– All clocks are active
Low-power mode 0 (LPM0)
– CPU is disabled
– ACLK and SMCLK remain active, MCLK is disabled
– FLL loop control remains active
Low-power mode 1 (LPM1)
– CPU is disabled
– FLL loop control is disabled
– ACLK and SMCLK remain active, MCLK is disabled
Low-power mode 2 (LPM2)
– CPU is disabled
– MCLK and FLL loop control and DCOCLK are disabled
– DC generator of the DCO remains enabled
– ACLK remains active
Low-power mode 3 (LPM3)
– CPU is disabled
– MCLK, FLL loop control, and DCOCLK are disabled
– DC generator of the DCO is disabled
– ACLK remains active
Low-power mode 4 (LPM4)
– CPU is disabled
– ACLK is disabled
– MCLK, FLL loop control, and DCOCLK are disabled
– DC generator of the DCO is disabled
– Crystal oscillator is stopped
– Complete data retention
Low-power mode 4.5 (LPM4.5)
– Internal regulator disabled
– No data retention
– Wake-up input from RST/NMI, P1, or P2
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
47
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.3 Interrupt Vector Addresses
The interrupt vectors and the power-up start address are in the address range 0FFFFh to 0FF80h (see Table
9-1). The vector contains the 16-bit address of the interrupt-handler instruction sequence.
Table 9-1. Interrupt Sources, Flags, and Vectors
INTERRUPT SOURCE
INTERRUPT FLAG
SYSTEM
INTERRUPT
WORD
ADDRESS
PRIORITY
System Reset
Power up
External reset
Watchdog time-out, password
violation
Flash memory password violation
PMM password violation
WDTIFG, KEYV (SYSRSTIV)(1) (3)
Reset
0FFFEh
63, highest
System NMI
PMM
Vacant memory access
JTAG mailbox
SVMLIFG, SVMHIFG, DLYLIFG, DLYHIFG,
VLRLIFG, VLRHIFG, VMAIFG, JMBNIFG,
JMBOUTIFG (SYSSNIV)(1)
(Non)maskable
0FFFCh
62
(Non)maskable
0FFFAh
61
User NMI
NMI
Oscillator fault
Flash memory access violation
COMP_B
NMIIFG, OFIFG, ACCVIFG, BUSIFG (SYSUNIV)
(1) (3)
Comparator B interrupt flags (CBIV)(1) (2)
Maskable
0FFF8h
60
USCI_A0 receive or transmit
UCA0RXIFG, UCA0TXIFG
(UCA0IV)(1) (2)
Maskable
0FFF6h
59
USCI_B0 receive or transmit
UCB0RXIFG, UCB0TXIFG (UCB0IV)(1) (2)
Maskable
0FFF4h
58
Watchdog timer interval timer mode
WDTIFG
Maskable
0FFF2h
57
USCI_A1 receive or transmit
UCA1RXIFG, UCA1TXIFG (UCA1IV)(1) (2)
Maskable
0FFF0h
56
USCI_B1 receive or transmit
UCB1RXIFG, UCB1TXIFG (UCB1IV)(1) (2)
Maskable
0FFEEh
55
ADC10_A
ADC10IFG0(1) (2) (5)
Maskable
0FFECh
54
USCI_A2 receive or transmit
UCA2RXIFG, UCA2TXIFG (UCA2IV)(1) (2)
Maskable
0FFEAh
53
USCI_B2 receive or transmit
(UCB2IV)(1) (2)
Maskable
0FFE8h
52
TA0
TA0CCR0 CCIFG0(2)
Maskable
0FFE6h
51
TA0
TA0CCR1 CCIFG1 to TA0CCR4 CCIFG4,
TA0IFG (TA0IV)(1) (2)
Maskable
0FFE4h
50
Reserved
Reserved(4)
Maskable
0FFE2h
49
DMA
DMA0IFG, DMA1IFG, DMA2IFG (DMAIV)(1) (2)
Maskable
0FFE0h
48
USCI_A3 receive or transmit
UCA3RXIFG, UCA3TXIFG
(UCA3IV)(1) (2)
Maskable
0FFDEh
47
USCI_B3 receive or transmit
UCB3RXIFG, UCB3TXIFG (UCB3IV)(1) (2)
Maskable
0FFDCh
46
TB0
48
UCB2RXIFG, UCB2TXIFG
Maskable
0FFDAh
45
TB0
TB0CCR1 CCIFG1 to TB0CCR6 CCIFG6,
TB0IFG (TB0IV)(1) (2)
Maskable
0FFD8h
44
TA1
TA1CCR0 CCIFG0(2)
Maskable
0FFD6h
43
TA1
TA1CCR1 CCIFG1 to TA1CCR2 CCIFG2,
TA1IFG (TA1IV)(1) (2)
Maskable
0FFD4h
42
I/O port P1
P1IFG.0 to P1IFG.7 (P1IV)(1) (2)
Maskable
0FFD2h
41
TA2
TA2CCR0 CCIFG0(2)
Maskable
0FFD0h
40
TA2
TA2CCR1 CCIFG1 to TA2CCR2 CCIFG2,
TA2IFG (TA2IV)(1) (2)
Maskable
0FFCEh
39
I/O port P2
P2IFG.0 to P2IFG.7 (P2IV)(1) (2)
Maskable
0FFCCh
38
RTC_A
RTCRDYIFG, RTCTEVIFG, RTCAIFG,
RT0PSIFG, RT1PSIFG (RTCIV)(1) (2)
Maskable
0FFCAh
37
I/O Port P6
P6IFG.0 to P6IFG.7 (P6IV)(1) (2)
Maskable
0FFC8h
36
Submit Document Feedback
TB0CCR0 CCIFG0
(2)
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-1. Interrupt Sources, Flags, and Vectors (continued)
(1)
(2)
(3)
(4)
(5)
INTERRUPT SOURCE
INTERRUPT FLAG
Reserved
Reserved(4)
SYSTEM
INTERRUPT
WORD
ADDRESS
PRIORITY
0FFC6h
35
⋮
⋮
0FF80h
0, lowest
Multiple source flags
Interrupt flags are in the module.
A reset is generated if the CPU tries to fetch instructions from within peripheral space or vacant memory space.
(Non)maskable: the individual interrupt enable bit can disable an interrupt event, but the general interrupt enable bit cannot disable it.
Reserved interrupt vectors at addresses are not used in this device and can be used for regular program code if necessary. To
maintain compatibility with other devices, TI recommends reserving these locations.
Only on devices with ADC, otherwise reserved
9.4 Memory Organization
Table 9-2 summarizes the memory map of the microcontrollers.
Table 9-2. Memory Organization
Memory (flash)
MSP430F5259, MSP430F5258,
MSP430F5255, MSP430F5254
MSP430F5257, MSP430F5256,
MSP430F5253, MSP430F5252
128KB
128KB
00FFFFh to 00FF80h
00FFFFh to 00FF80h
Bank D
32KB
002A3FFh to 0022400h
32KB
002A3FFh to 0022400h
Bank C
32KB
00223FFh to 001A400h
32KB
00223FFh to 001A400h
Bank B
32KB
001A3FFh to 0012400h
32KB
001A3FFh to 0012400h
Bank A
32KB
00123FFh to 00A400h
32KB
00123FFh to 00A400h
Sector 7
4KB
00A3FFh to 009400h
N/A(1)
Sector 6
4KB
0093FFh to 008400h
N/A
Sector 5
4KB
0083FFh to 007400h
N/A
Sector 4
4KB
0073FFh to 006400h
N/A
Sector 3
4KB
0063FFh to 005400h
4KB
0063FFh to 005400h
Sector 2
4KB
0053FFh to 004400h
4KB
0053FFh to 004400h
Sector 1
4KB
0043FFh to 003400h
4KB
0043FFh to 003400h
Sector 0
4KB
0033FFh to 002400h
4KB
0033FFh to 002400h
A
128 bytes
001BFFh to 001B80h
128 bytes
001BFFh to 001B80h
B
128 bytes
001B7Fh to 001B00h
128 bytes
001B7Fh to 001B00h
C
128 bytes
001AFFh to 001A80h
128 bytes
001AFFh to 001A80h
D
128 bytes
001A7Fh to 001A00h
128 bytes
001A7Fh to 001A00h
Total Size
Main: interrupt vector
Main: code memory
RAM
TI factory memory (ROM)
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
49
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-2. Memory Organization (continued)
MSP430F5259, MSP430F5258,
MSP430F5255, MSP430F5254
MSP430F5257, MSP430F5256,
MSP430F5253, MSP430F5252
Info A
128 bytes
0019FFh to 001980h
128 bytes
0019FFh to 001980h
Info B
128 bytes
00197Fh to 001900h
128 bytes
00197Fh to 001900h
Info C
128 bytes
0018FFh to 001880h
128 bytes
0018FFh to 001880h
Info D
128 bytes
00187Fh to 001800h
128 bytes
00187Fh to 001800h
BSL 3
512 bytes
0017FFh to 001600h
512 bytes
0017FFh to 001600h
BSL 2
512 bytes
0015FFh to 001400h
512 bytes
0015FFh to 001400h
BSL 1
512 bytes
0013FFh to 001200h
512 bytes
0013FFh to 001200h
BSL 0
512 bytes
0011FFh to 001000h
512 bytes
0011FFh to 001000h
4KB
000FFFh to 0h
4KB
000FFFh to 0h
Information memory (flash)
Bootloader (BSL) memory (flash)
Peripherals
(1)
Size
N/A = Not available
9.5 Bootloader (BSL)
Note
Devices from TI come factory programmed with either an I2C-based BSL or a timer-based UART BSL.
See Table 6-1 to determine which BSL type is implemented.
9.5.1 Bootloader – I2C
The I 2C BSL enables users to program the flash memory or RAM using a I 2C serial interface. Access to the
device memory through the BSL is protected by an user-defined password.
When using the BSL, it requires a specific entry sequence on the RST/NMI and BSLEN pins. Table 9-3 lists the
required pins and their functions. For further details on interfacing to development tools and device
programmers, see the MSP430 Hardware Tools User's Guide. For a complete description of the features of the
BSL and its implementation, see the MSP430 Flash Devices Bootloader (BSL) User's Guide. BSL firmware
images are available for download in the Custom BSL430 package.
Note
To invoke the BSL from the DVIO domain, the RST/NMI pin and BSLEN pins must be used for the
entry sequence. It is critical not to confuse the RST/NMI pin with the RSTDVCC/SBWTDIO pin. In
many other MSP430 devices, SBWTDIO is shared with the RST/NMI pin, and RSTDVCC does not
exist. Additional information can be found in Designing With MSP430F522x and MSP430F521x
Devices.
50
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-3. BSL Pin Requirements and Functions
DEVICE SIGNAL
BSL FUNCTION
RST/NMI
External reset
BSLEN
Enable BSL
P4.1/PM_UCB1SDA
I2C data
P4.2/ PM_UCB1SCL
I2C clock
DVCC, AVCC
Device power supply
DVIO
I/O power supply
DVSS
Ground supply
9.5.2 Bootloader – UART
The UART BSL enables users to program the flash memory or RAM using a UART serial interface. Access to
the device memory through the BSL is protected by an user-defined password. Because the F525x have split I/O
power domains, it is possible to interface with the BSL from either the DVCC or DVIO supply domains. This is
useful when the MSP430 is interfacing to a host on the DVIO supply domain. The BSL interface on the DVIO
supply domain (see Table 9-5) uses the USCI_A0 module configured as a UART. The BSL interface on the
DVCC supply domain (see Table 9-4) uses a timer-based UART.
For applications that have BSL communication based on the DVCC supply domain, entry to the BSL requires a
specific sequence on the RSTDVCC/SBWTDIO and TEST/SBWTCK pins.
Note
Devices that are factory programmed with an UART BSL use the DVCC power supply domain pin
configuration per default (see Table 9-4).
Note
To invoke the BSL from the DVCC domain, the RSTDVCC/SBWTDIO pin and TEST/SBWTCK pin
must be used for the entry sequence. It is critical not to confuse the RST/NMI pin with the RSTDVCC/
SBWTDIO pin. In many other MSP430 devices, SBWTDIO is shared with the RST/NMI pin, and
RSTDVCC does not exist. Additional information can be found in Designing With MSP430F522x and
MSP430F521x Devices.
Table 9-4. DVCC BSL Pin Requirements and
Functions
DEVICE SIGNAL
BSL FUNCTION
RSTDVCC/SBWTDIO
External reset
TEST/SBWTCK
Enable BSL
P6.1
Data transmit
P6.2
Data receive
DVCC, AVCC
Device power supply
DVIO
I/O power supply
DVSS
Ground supply
When using the DVIO supply domain for the BSL, entry to the BSL requires a specific sequence on the RST/NMI
and BSLEN pins. Table 9-5 lists the required pins and their functions. For further details on interfacing to
development tools and device programmers, see the MSP430 Hardware Tools User's Guide. For a complete
description of the features of the BSL and its implementation, see the MSP430 Flash Device Bootloader (BSL)
User's Guide. BSL firmware images are available for download in the Custom BSL430 package. The BSL on the
DVIO supply domain uses the USCI_A0 module configured as a UART.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
51
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Note
To invoke the BSL from the DVIO domain, the RST/NMI pin and the BSLEN pin must be used for the
entry sequence (see Section 8.49). It is critical not to confuse the RST/NMI pin with the RSTDVCC/
SBWTDIO pin. In many other MSP430 devices, SBWTDIO is shared with the RST/NMI pin, and
RSTDVCC does not exist. Additional information can be found in Designing With MSP430F522x and
MSP430F521x Devices.
Table 9-5. DVIO BSL Pin Requirements and
Functions
DEVICE SIGNAL
BSL FUNCTION
RST/NMI
External reset
BSLEN
Enable BSL
P3.3
Data transmit
P3.4
Data receive
DVCC, AVCC
Device power supply
DVIO
I/O power supply
DVSS
Ground supply
9.6 JTAG Operation
9.6.1 JTAG Standard Interface
The MSP430 family supports the standard JTAG interface which requires four signals for sending and receiving
data. The JTAG signals are shared with general-purpose I/O. The TEST/SBWTCK pin is used to enable the
JTAG signals. In addition to these signals, the RSTDVCC/SBWTDIO is required to interface with MSP430
development tools and device programmers. Table 9-6 lists the JTAG pin requirements. For further details on
interfacing to development tools and device programmers, see the MSP430 Hardware Tools User's Guide. For a
complete description of the features of the JTAG interface and its implementation, see MSP430 Programming
With the JTAG Interface. Additional information can be found in Designing With MSP430F522x and
MSP430F521x Devices.
Note
All JTAG I/O pins are supplied by DVCC.
Note
Traditionally, on other MSP430 devices, the RST/NMI pin is used for SBWTDIO, so care must be
taken not to mistakenly use the incorrect pin. On the F525x series of devices, it is required to use
RSTDVCC for SBWTDIO as shown in Table 9-6. Additional information can be found in Designing
With MSP430F522x and MSP430F521x Devices.
52
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-6. JTAG Pin Requirements and Functions
DEVICE SIGNAL
DIRECTION
FUNCTION
PJ.3/TCK
IN
JTAG clock input
PJ.2/TMS
IN
JTAG state control
PJ.1/TDI/TCLK
IN
JTAG data input, TCLK input
PJ.0/TDO
OUT
JTAG data output
TEST/SBWTCK
IN
Enable JTAG pins
RSTDVCC/SBWTDIO
IN
External reset
DVCC, AVCC
Device power supply
DVIO
I/O power supply
DVSS
Ground supply
9.6.2 Spy-Bi-Wire Interface
In addition to the standard JTAG interface, the MSP430 family supports the two wire Spy-Bi-Wire interface. SpyBi-Wire can be used to interface with MSP430 development tools and device programmers. Table 9-7 lists the
Spy-Bi-Wire interface pin requirements. For further details on interfacing to development tools and device
programmers, see the MSP430 Hardware Tools User's Guide. For a complete description of the features of the
JTAG interface and its implementation, see MSP430 Programming With the JTAG Interface. Additional
information can be found in Designing With MSP430F522x and MSP430F521x Devices.
Note
All SBW I/O pins are supplied by DVCC.
Note
Traditionally, on other MSP430 devices, the RST/NMI pin is used for SBWTDIO, so care must be
taken not to mistakenly use the incorrect pin. On the F525x series of devices, it is required to use
RSTDVCC for SBWTDIO as shown in Table 9-7. Additional information can be found in Designing
With MSP430F522x and MSP430F521x Devices.
Table 9-7. Spy-Bi-Wire Pin Requirements and Functions
DEVICE SIGNAL
DIRECTION
FUNCTION
TEST/SBWTCK
IN
Spy-Bi-Wire clock input
RSTDVCC/SBWTDIO
IN, OUT
Spy-Bi-Wire data input/output
DVCC, AVCC
Device power supply
DVIO
I/O power supply
DVSS
Ground supply
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
53
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.7 Flash Memory
The flash memory can be programmed through the JTAG port, Spy-Bi-Wire (SBW), the BSL, or in-system by the
CPU. The CPU can perform single-byte, single-word, and long-word writes to the flash memory. Features of the
flash memory include:
•
•
•
•
Flash memory has n segments of main memory and four segments of information memory (A to D) of
128 bytes each. Each segment in main memory is 512 bytes in size.
Segments 0 to n may be erased in one step, or each segment may be individually erased.
Segments A to D can be erased individually. Segments A to D are also called information memory.
Segment A can be locked separately.
9.8 RAM
The RAM is made up of n sectors. Each sector can be completely powered down to reduce leakage; however, all
data are lost during power down.
Features of the RAM include:
•
•
•
54
RAM memory has n sectors. The sizes of the sectors can be found in Section 9.4, Memory Organization.
Each sector 0 to n can be complete disabled; however, all data in a sector are lost when it is disabled.
Each sector 0 to n automatically enters low-power retention mode when possible.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9 Peripherals
Peripherals are connected to the CPU through data, address, and control buses. Peripherals can be managed
using all instructions. For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User's
Guide.
9.9.1 Digital I/O
•
•
•
•
•
•
•
•
All individual I/O bits are independently programmable.
Any combination of input, output, and interrupt conditions is possible.
Pullup or pulldown on all ports is programmable.
Drive strength on all ports is programmable.
Edge-selectable interrupt and LPM4.5 wake-up input capability is available for all bits of ports P1, P2.
All bits of port P6 support edge-selectable interrupt input.
All instructions support read and write access to port-control registers.
Ports can be accessed byte-wise or word-wise in pairs.
9.9.2 Port Mapping Controller
The port mapping controller allows the flexible and reconfigurable mapping of digital functions to port P4 (see
Table 9-8).
Table 9-8. Port Mapping Mnemonics and Functions
VALUE
PxMAPy MNEMONIC
INPUT PIN FUNCTION
OUTPUT PIN FUNCTION
0
PM_NONE
None
DVSS
PM_CBOUT0
–
COMP_B output
PM_TB0CLK
TB0 clock input
–
PM_ADC10CLK
–
ADC10CLK
1
2
3
4
PM_DMAE0
DMAE0 input
–
PM_SVMOUT
–
SVM output
PM_TB0OUTH
TB0 high-impedance input TB0OUTH
–
PM_TB0CCR0A
TB0 CCR0 capture input CCI0A
TB0 CCR0 compare output Out0
5
PM_TB0CCR1A
TB0 CCR1 capture input CCI1A
TB0 CCR1 compare output Out1
6
PM_TB0CCR2A
TB0 CCR2 capture input CCI2A
TB0 CCR2 compare output Out2
7
PM_TB0CCR3A
TB0 CCR3 capture input CCI3A
TB0 CCR3 compare output Out3
8
PM_TB0CCR4A
TB0 CCR4 capture input CCI4A
TB0 CCR4 compare output Out4
9
PM_TB0CCR5A
TB0 CCR5 capture input CCI5A
TB0 CCR5 compare output Out5
10
PM_TB0CCR6A
TB0 CCR6 capture input CCI6A
TB0 CCR6 compare output Out6
11
12
13
14
15
16
17
PM_UCA1RXD
USCI_A1 UART RXD (direction controlled by USCI – input)
PM_UCA1SOMI
USCI_A1 SPI slave out master in (direction controlled by USCI)
PM_UCA1TXD
USCI_A1 UART TXD (direction controlled by USCI – output)
PM_UCA1SIMO
USCI_A1 SPI slave in master out (direction controlled by USCI)
PM_UCA1CLK
USCI_A1 clock input/output (direction controlled by USCI)
PM_UCB1STE
USCI_B1 SPI slave transmit enable (direction controlled by USCI)
PM_UCB1SOMI
USCI_B1 SPI slave out master in (direction controlled by USCI)
PM_UCB1SCL
USCI_B1 I2C clock (open drain and direction controlled by USCI)
PM_UCB1SIMO
USCI_B1 SPI slave in master out (direction controlled by USCI)
PM_UCB1SDA
USCI_B1 I2C data (open drain and direction controlled by USCI)
PM_UCB1CLK
USCI_B1 clock input/output (direction controlled by USCI)
PM_UCA1STE
USCI_A1 SPI slave transmit enable (direction controlled by USCI)
PM_CBOUT1
Copyright © 2020 Texas Instruments Incorporated
None
COMP_B output
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
55
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-8. Port Mapping Mnemonics and Functions (continued)
VALUE
PxMAPy MNEMONIC
INPUT PIN FUNCTION
OUTPUT PIN FUNCTION
18
PM_MCLK
None
MCLK
None
RTCCLK output
19
PM_RTCCLK
20
21
22
23
24
25
USCI_A0 UART RXD (direction controlled by USCI – input)
PM_UCA0SOMI
USCI_A0 SPI slave out master in (direction controlled by USCI)
PM_UCA0TXD
USCI_A0 UART TXD (direction controlled by USCI – output)
PM_UCA0SIMO
USCI_A0 SPI slave in master out (direction controlled by USCI)
PM_UCA0CLK
USCI_A0 clock input/output (direction controlled by USCI)
PM_UCB0STE
USCI_B0 SPI slave transmit enable (direction controlled by USCI)
PM_UCB0SOMI
USCI_B0 SPI slave out master in (direction controlled by USCI)
PM_UCB0SCL
USCI_B0 I2C clock (open drain and direction controlled by USCI)
PM_UCB0SIMO
USCI_B0 SPI slave in master out (direction controlled by USCI)
PM_UCB0SDA
USCI_B0 I2C data (open drain and direction controlled by USCI)
PM_UCB0CLK
USCI_B0 clock input/output (direction controlled by USCI)
PM_UCA0STE
USCI_A0 SPI slave transmit enable (direction controlled by USCI)
PM_UCA3RXD
USCI_A3 UART RXD (direction controlled by USCI – input)
PM_UCA3SOMI
USCI_A3 SPI slave out master in (direction controlled by USCI)
PM_UCA3TXD
USCI_A3 UART TXD (direction controlled by USCI – output)
PM_UCA3SIMO
USCI_A3 SPI slave in master out (direction controlled by USCI)
PM_UCB3SIMO
USCI_B3 SPI slave in master out (direction controlled by USCI)
PM_UCB3SDA
USCI_B3 I2C data (open drain and direction controlled by USCI)
PM_UCB3SOMI
USCI_B3 SPI slave out master in (direction controlled by USCI)
PM_UCB3SCL
USCI_B3 I2C clock (open drain and direction controlled by USCI)
30
Reserved
Reserved
31 (0FFh)(1)
PM_ANALOG
Disables the output driver and the input Schmitt trigger to prevent parasitic
cross currents when applying analog signals
26
27
28
29
(1)
PM_UCA0RXD
The value of the PM_ANALOG mnemonic is 0FFh. The port mapping registers are only 5 bits wide, and the upper bits are ignored,
which results in a read value of 31.
Table 9-9 lists the default settings for all pins that support port mapping.
Table 9-9. Default Mapping
PIN
56
PxMAPy MNEMONIC
INPUT PIN FUNCTION
OUTPUT PIN FUNCTION
P4.0/P4MAP0
PM_UCB1STE/PM_UCA1CLK
USCI_B1 SPI slave transmit enable (direction controlled by USCI)
USCI_A1 clock input/output (direction controlled by USCI)
P4.1/P4MAP1
PM_UCB1SIMO/PM_UCB1SDA
USCI_B1 SPI slave in master out (direction controlled by USCI)
USCI_B1 I2C data (open drain and direction controlled by USCI)
P4.2/P4MAP2
PM_UCB1SOMI/PM_UCB1SCL
USCI_B1 SPI slave out master in (direction controlled by USCI)
USCI_B1 I2C clock (open drain and direction controlled by USCI)
P4.3/P4MAP3
PM_UCB1CLK/PM_UCA1STE
USCI_A1 SPI slave transmit enable (direction controlled by USCI)
USCI_B1 clock input/output (direction controlled by USCI)
P4.4/P4MAP4
PM_UCA1TXD/PM_UCA1SIMO
USCI_A1 UART TXD (Direction controlled by USCI – output)
USCI_A1 SPI slave in master out (direction controlled by USCI)
P4.5/P4MAP5
PM_UCA1RXD/PM_UCA1SOMI
USCI_A1 UART RXD (Direction controlled by USCI – input)
USCI_A1 SPI slave out master in (direction controlled by USCI)
P4.6/P4MAP6
PM_UCA3TXD/PM_UCA3SIMO
USCI_A3 UART TXD (Direction controlled by USCI – output)
USCI_A3 SPI slave in master out (direction controlled by USCI)
P4.7/P4MAP7
PM_UCA3RXD/PM_UCA3SOMI
USCI_A3 UART RXD (Direction controlled by USCI – input)
USCI_A3 SPI slave out master in (direction controlled by USCI)
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.3 Oscillator and System Clock
The clock system is supported by the Unified Clock System (UCS) module, which includes support for a 32-kHz
watch crystal oscillator (XT1 LF mode; XT1 HF mode is not supported), an internal very-low-power lowfrequency oscillator (VLO), an internal trimmed low-frequency oscillator (REFO), an integrated internal digitally
controlled oscillator (DCO), and a high-frequency crystal oscillator (XT2). The UCS module is designed to meet
the requirements of both low system cost and low power consumption. The UCS module features digital
frequency locked loop (FLL) hardware that, in conjunction with a digital modulator, stabilizes the DCO frequency
to a programmable multiple of the selected FLL reference frequency. The internal DCO provides a fast turnon
clock source and stabilizes in 3.5 µs (typical). The UCS module provides the following clock signals:
•
•
•
•
Auxiliary clock (ACLK), sourced from a 32-kHz watch crystal (XT1), a high-frequency crystal (XT2), the
internal low-frequency oscillator (VLO), the trimmed low-frequency oscillator (REFO), or the internal digitally
controlled oscillator DCO.
Main clock (MCLK), the system clock used by the CPU. MCLK can be sourced by same sources made
available to ACLK.
Sub-Main clock (SMCLK), the subsystem clock used by the peripheral modules. SMCLK can be sourced by
same sources made available to ACLK.
ACLK/n, the buffered output of ACLK, ACLK/2, ACLK/4, ACLK/8, ACLK/16, ACLK/32.
9.9.4 Power-Management Module (PMM)
The PMM includes an integrated voltage regulator that supplies the core voltage to the device and contains
programmable output levels to provide for power optimization. The PMM also includes supply voltage supervisor
(SVS) and supply voltage monitoring (SVM) circuitry, and brownout protection. The brownout circuit is
implemented to provide the proper internal reset signal to the device during power-on and power-off. The SVS
and SVM circuitry detects if the supply voltage drops below a user-selectable level and supports both supply
voltage supervision (the device is automatically reset) and supply voltage monitoring (the device is not
automatically reset). SVS and SVM circuitry is available on the primary supply and core supply.
9.9.5 Hardware Multiplier
The multiplication operation is supported by a dedicated peripheral module. The module performs operations
with 32-, 24-, 16-, and 8-bit operands. The module supports signed and unsigned multiplication as well as signed
and unsigned multiply-and-accumulate operations.
9.9.6 Real-Time Clock (RTC_A)
The RTC_A module can be used as a general-purpose 32-bit counter (counter mode) or as an integrated realtime clock (RTC) (calendar mode). In counter mode, the RTC_A also includes two independent 8-bit timers that
can be cascaded to form a 16-bit timer or counter. Both timers can be read and written by software. Calendar
mode integrates an internal calendar that compensates for months with less than 31 days and includes leap year
correction. The RTC_A also supports flexible alarm functions and offset-calibration hardware.
9.9.7 Watchdog Timer (WDT_A)
The primary function of the WDT_A module is to perform a controlled system restart after a software problem
occurs. If the selected time interval expires, a system reset is generated. If the watchdog function is not needed
in an application, the module can be configured as an interval timer and can generate interrupts at selected time
intervals.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
57
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.8 System Module (SYS)
The SYS module handles many of the system functions within the device. These functions include power-on
reset (POR) and power-up clear (PUC) handling, NMI source selection and management, reset interrupt vector
generators, bootloader (BSL) entry mechanisms, and configuration management (device descriptors). The SYS
module also includes a data exchange mechanism using JTAG that is called a JTAG mailbox and that can be
used in the application. Table 9-10 lists the SYS module interrupt vector registers.
Table 9-10. System Module Interrupt Vector Registers
INTERRUPT VECTOR
REGISTER
SYSRSTIV, System Reset
SYSSNIV, System NMI
SYSUNIV, User NMI
58
Submit Document Feedback
ADDRESS
019Eh
019Ch
019Ah
INTERRUPT EVENT
VALUE
No interrupt pending
00h
Brownout (BOR)
02h
RST/NMI (BOR)
04h
PMMSWBOR (BOR)
06h
Wakeup from LPMx.5
08h
Security violation (BOR)
0Ah
SVSL (POR)
0Ch
SVSH (POR)
0Eh
SVML_OVP (POR)
10h
SVMH_OVP (POR)
12h
PMMSWPOR (POR)
14h
WDT time-out (PUC)
16h
WDT password violation (PUC)
18h
KEYV flash password violation (PUC)
1Ah
Reserved
1Ch
Peripheral area fetch (PUC)
1Eh
PMM password violation (PUC)
20h
Reserved
22h to 3Eh
No interrupt pending
00h
SVMLIFG
02h
SVMHIFG
04h
SVSMLDLYIFG
06h
SVSMHDLYIFG
08h
VMAIFG
0Ah
JMBINIFG
0Ch
JMBOUTIFG
0Eh
SVMLVLRIFG
10h
SVMHVLRIFG
12h
Reserved
14h to 1Eh
No interrupt pending
00h
NMIIFG
02h
OFIFG
04h
ACCVIFG
06h
Reserved
08h
Reserved
0Ah to 1Eh
PRIORITY
Highest
Lowest
Highest
Lowest
Highest
Lowest
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.9 DMA Controller
The DMA controller allows movement of data from one memory address to another without CPU intervention.
For example, the DMA controller can be used to move data from the ADC10_A conversion memory to RAM.
Using the DMA controller can increase the throughput of peripheral modules. The DMA controller reduces
system power consumption by allowing the CPU to remain in sleep mode, without having to awaken to move
data to or from a peripheral (see Table 9-11).
Table 9-11. DMA Trigger Assignments
CHANNEL
TRIGGER(1)
(1)
(2)
0
1
2
0
DMAREQ
DMAREQ
DMAREQ
1
TA0CCR0 CCIFG
TA0CCR0 CCIFG
TA0CCR0 CCIFG
2
TA0CCR2 CCIFG
TA0CCR2 CCIFG
TA0CCR2 CCIFG
3
TA1CCR0 CCIFG
TA1CCR0 CCIFG
TA1CCR0 CCIFG
4
TA1CCR2 CCIFG
TA1CCR2 CCIFG
TA1CCR2 CCIFG
5
TA2CCR0 CCIFG
TA2CCR0 CCIFG
TA2CCR0 CCIFG
6
TA2CCR2 CCIFG
TA2CCR2 CCIFG
TA2CCR2 CCIFG
7
TB0CCR0 CCIFG
TB0CCR0 CCIFG
TB0CCR0 CCIFG
8
TB0CCR2 CCIFG
TB0CCR2 CCIFG
TB0CCR2 CCIFG
9
UCA2RXIFG
UCA2RXIFG
UCA2RXIFG
10
UCA2TXIFG
UCA2TXIFG
UCA2TXIFG
11
UCB2RXIFG
UCB2RXIFG
UCB2RXIFG
12
UCB2TXIFG
UCB2TXIFG
UCB2TXIFG
13
Reserved
Reserved
Reserved
14
Reserved
Reserved
Reserved
15
Reserved
Reserved
Reserved
16
UCA0RXIFG
UCA0RXIFG
UCA0RXIFG
17
UCA0TXIFG
UCA0TXIFG
UCA0TXIFG
18
UCB0RXIFG
UCB0RXIFG
UCB0RXIFG
19
UCB0TXIFG
UCB0TXIFG
UCB0TXIFG
20
UCA1RXIFG
UCA1RXIFG
UCA1RXIFG
21
UCA1TXIFG
UCA1TXIFG
UCA1TXIFG
22
UCB1RXIFG
UCB1RXIFG
UCB1RXIFG
23
UCB1TXIFG
UCB1TXIFG
UCB1TXIFG
24
ADC10IFG0(2)
ADC10IFG0(2)
ADC10IFG0(2)
25
UCA3RXIFG
UCA3RXIFG
UCA3RXIFG
26
UCA3TXIFG
UCA3TXIFG
UCA3TXIFG
27
UCB3RXIFG
UCB3RXIFG
UCB3RXIFG
28
UCB3TXIFG
UCB3TXIFG
UCB3TXIFG
29
MPY ready
MPY ready
MPY ready
30
DMA2IFG
DMA0IFG
DMA1IFG
31
DMAE0
DMAE0
DMAE0
If a reserved trigger source is selected, no trigger is generated.
Only on devices with ADC; reserved on devices without ADC
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
59
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.10 Universal Serial Communication Interface (USCI)
The USCI modules are used for serial data communication. The USCI module supports synchronous
communication protocols such as SPI (3- or 4-pin) and I2C, and asynchronous communication protocols such as
UART, enhanced UART with automatic baud-rate detection, and IrDA. Each USCI module contains two portions,
A and B.
The USCI_An module provides support for SPI (3- or 4-pin), UART, enhanced UART, or IrDA.
The USCI_Bn module provides support for SPI (3- or 4-pin) or I2C.
The MSP430F525x include four complete USCI modules (n = 0, 1, 2, 3).
9.9.11 TA0
TA0 is a 16-bit timer/counter (Timer_A type) with five capture/compare registers. TA0 supports multiple captures
or compares, PWM outputs, and interval timing (see Table 9-12). TA0 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Table 9-12. TA0 Signal Connections
INPUT PIN
NUMBER
RGC, ZXH, ZQE
18, H2 - P1.0
TA0CLK
ACLK (internal)
ACLK
SMCLK
18, H2 - P1.0
TA0CLK
TACLK
19, H3 - P1.1
TA0.0
CCI0A
DVSS
CCI0B
DVSS
GND
21, G4 - P1.3
22, H4 - P1.4
23, J4 - P1.5
DVCC
VCC
TA0.1
CCI1A
CBOUT
(internal)
CCI1B
DVSS
GND
DVCC
VCC
TA0.2
CCI2A
ACLK (internal)
CCI2B
DVSS
GND
DVCC
VCC
TA0.3
CCI3A
DVSS
CCI3B
DVSS
GND
DVCC
VCC
TA0.4
CCI4A
DVSS
CCI4B
DVSS
GND
DVCC
VCC
Submit Document Feedback
MODULE
BLOCK
MODULE
OUTPUT
SIGNAL
DEVICE
OUTPUT
SIGNAL
Timer
NA
NA
OUTPUT PIN NUMBER
RGC, ZXH, ZQE
TACLK
SMCLK (internal)
20, J3 - P1.2
60
DEVICE INPUT MODULE INPUT
SIGNAL
SIGNAL
19, H3 - P1.1
CCR0
TA0
TA0.0
20, J3 - P1.2
CCR1
TA1
TA0.1
ADC10 (internal)
ADC10SHSx = {1}
21, G4 - P1.3
CCR2
TA2
TA0.2
22, H4 - P1.4
CCR3
TA3
TA0.3
23, J4 - P1.5
CCR4
TA4
TA0.4
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.12 TA1
TA1 is a 16-bit timer/counter (Timer_A type) with three capture/compare registers. TA1 supports multiple
captures or compares, PWM outputs, and interval timing (see Table 9-13). TA1 also has extensive interrupt
capabilities. Interrupts may be generated from the counter on overflow conditions and from each of the capture/
compare registers.
Table 9-13. TA1 Signal Connections
INPUT PIN
NUMBER
RGC, ZQE
24, G5 - P1.6
24, G5 - P1.6
25, H5 - P1.7
26, J5 - P2.0
27, G6 - P2.1
DEVICE INPUT
SIGNAL
MODULE INPUT
SIGNAL
TA1CLK
TACLK
ACLK (internal)
ACLK
SMCLK (internal)
SMCLK
TA1CLK
TACLK
TA1.0
CCI0A
DVSS
CCI0B
DVSS
GND
DVCC
VCC
TA1.1
CCI1A
CBOUT (internal)
CCI1B
DVSS
GND
DVCC
VCC
TA1.2
CCI2A
ACLK (internal)
CCI2B
DVSS
GND
DVCC
VCC
Copyright © 2020 Texas Instruments Incorporated
MODULE BLOCK
Timer
MODULE
DEVICE OUTPUT
OUTPUT SIGNAL
SIGNAL
NA
OUTPUT PIN
NUMBER
RGC, ZQE
NA
25, H5 - P1.7
CCR0
TA0
TA1.0
26, J5 - P2.0
CCR1
TA1
TA1.1
27, G6 - P2.1
CCR2
TA2
TA1.2
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
61
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.13 TA2
TA2 is a 16-bit timer/counter (Timer_A type) with three capture/compare registers. TA2 supports multiple
captures or compares, PWM outputs, and interval timing (see Table 9-14). TA2 also has extensive interrupt
capabilities. Interrupts may be generated from the counter on overflow conditions and from each of the capture/
compare registers.
Table 9-14. TA2 Signal Connections
INPUT PIN
NUMBER
RGC, ZXH, ZQE
1, A1 - P6.0
1, A1 - P6.0
2, B2 - P6.1
3, B1 - P6.2
4, C2 - P6.3
62
DEVICE INPUT
SIGNAL
MODULE INPUT
SIGNAL
TA2CLK
TACLK
ACLK (internal)
ACLK
SMCLK (internal)
SMCLK
TA2CLK
TACLK
TA2.0
CCI0A
DVSS
CCI0B
DVSS
GND
DVCC
VCC
TA2.1
CCI1A
CBOUT (internal)
CCI1B
DVSS
GND
DVCC
VCC
TA2.2
CCI2A
ACLK (internal)
CCI2B
DVSS
GND
DVCC
VCC
Submit Document Feedback
MODULE BLOCK
Timer
MODULE
DEVICE OUTPUT
OUTPUT SIGNAL
SIGNAL
NA
OUTPUT PIN
NUMBER
RGC, ZXH, ZQE
NA
2, B2 - P6.1
CCR0
TA0
TA2.0
3, B1 - P6.2
CCR1
TA1
TA2.1
4, C2 - P6.3
CCR2
TA2
TA2.2
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.14 TB0
TB0 is a 16-bit timer/counter (Timer_B type) with seven capture/compare registers. TB0 supports multiple
captures or compares, PWM outputs, and interval timing (see Table 9-15). TB0 also has extensive interrupt
capabilities. Interrupts may be generated from the counter on overflow conditions and from each of the capture/
compare registers.
Table 9-15. TB0 Signal Connections
INPUT PIN NUMBER
RGC, ZXH, ZQE
(1)
MODULE INPUT
SIGNAL
TB0CLK
TBCLK
ACLK (internal)
ACLK
SMCLK (internal)
SMCLK
(1)
TB0CLK
TBCLK
(1)
TB0.0
CCI0A
(1)
TB0.0
CCI0B
DVSS
GND
(1)
DVCC
VCC
TB0.1
CCI1A
CBOUT (internal)
CCI1B
DVSS
GND
DVCC
VCC
(1)
TB0.2
CCI2A
(1)
TB0.2
CCI2B
DVSS
GND
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
DEVICE INPUT
SIGNAL
DVCC
VCC
TB0.3
CCI3A
TB0.3
CCI3B
DVSS
GND
DVCC
VCC
TB0.4
CCI4A
TB0.4
CCI4B
DVSS
GND
DVCC
VCC
TB0.5
CCI5A
TB0.5
CCI5B
DVSS
GND
DVCC
VCC
TB0.6
CCI6A
ACLK (internal)
CCI6B
DVSS
GND
DVCC
VCC
MODULE BLOCK
MODULE OUTPUT
SIGNAL
DEVICE OUTPUT
SIGNAL
Timer
NA
NA
OUTPUT PIN NUMBER
RGC, ZXH, ZQE
(1)
CCR0
TB0
TB0.0
ADC10 (internal)
ADC10SHSx = {2}
(1)
CCR1
TB1
TB0.1
ADC10 (internal)
ADC10SHSx = {3}
(1)
CCR2
TB2
TB0.2
(1)
CCR3
TB3
TB0.3
(1)
CCR4
TB4
TB0.4
(1)
CCR5
TB5
TB0.5
(1)
CCR6
TB6
TB0.6
Timer functions can be selected by the port mapping controller.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
63
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.15 Comparator_B
The primary function of the Comparator_B module is to support precision slope analog-to-digital conversions,
battery voltage supervision, and monitoring of external analog signals.
9.9.16 ADC10_A
The ADC10_A module supports fast 10-bit analog-to-digital conversions. The module implements a 10-bit SAR
core, sample select control, reference generator, and a conversion result buffer. A window comparator with lower
and upper limits allows CPU-independent result monitoring with three window comparator interrupt flags.
9.9.17 CRC16
The CRC16 module produces a signature based on a sequence of entered data values and can be used for data
checking purposes. The CRC16 module signature is based on the CRC-CCITT standard.
9.9.18 Reference (REF) Module Voltage Reference
The REF module generates all of the critical reference voltages that can be used by the various analog
peripherals in the device.
9.9.19 Embedded Emulation Module (EEM) (S Version)
The EEM supports real-time in-system debugging. The S version of the EEM has the following features:
• Three hardware triggers or breakpoints on memory access
• One hardware trigger or breakpoint on CPU register write access
• Up to four hardware triggers can be combined to form complex triggers or breakpoints
• One cycle counter
• Clock control on module level
64
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.9.20 Peripheral File Map
Table 9-16 lists the base address for the registers of each peripheral module.
Table 9-16. Peripherals
MODULE NAME
BASE ADDRESS
OFFSET ADDRESS
RANGE
Special Functions (see Table 9-17)
0100h
000h to 01Fh
PMM (see Table 9-18)
0120h
000h to 010h
Flash Control (see Table 9-19)
0140h
000h to 00Fh
CRC16 (see Table 9-20)
0150h
000h to 007h
RAM Control (see Table 9-21)
0158h
000h to 001h
Watchdog (see Table 9-22)
015Ch
000h to 001h
UCS (see Table 9-23)
0160h
000h to 01Fh
SYS (see Table 9-24)
0180h
000h to 01Fh
Shared Reference (see Table 9-25)
01B0h
000h to 001h
Port Mapping Control (see Table 9-26)
01C0h
000h to 002h
Port Mapping Port P4 (see Table 9-26)
01E0h
000h to 007h
Port P1, P2 (see Table 9-27)
0200h
000h to 01Fh
Port P3, P4 (see Table 9-28)
0220h
000h to 00Bh
Port P5, P6 (see Table 9-29)
0240h
000h to 01Fh
Port P7 (see Table 9-30)
0260h
000h to 00Bh
Port PJ (see Table 9-31)
0320h
000h to 01Fh
TA0 (see Table 9-32)
0340h
000h to 02Eh
TA1 (see Table 9-33)
0380h
000h to 02Eh
TB0 (see Table 9-34)
03C0h
000h to 02Eh
TA2 (see Table 9-35)
0400h
000h to 02Eh
Real-Time Clock (RTC_A) (see Table 9-36)
04A0h
000h to 01Bh
32-Bit Hardware Multiplier (see Table 9-37)
04C0h
000h to 02Fh
DMA General Control (see Table 9-38)
0500h
000h to 00Fh
DMA Channel 0 (see Table 9-38)
0510h
000h to 00Ah
DMA Channel 1 (see Table 9-38)
0520h
000h to 00Ah
DMA Channel 2 (see Table 9-38)
0530h
000h to 00Ah
USCI_A0 (see Table 9-39)
05C0h
000h to 01Fh
USCI_B0 (see Table 9-40)
05E0h
000h to 01Fh
USCI_A1 (see Table 9-41)
0600h
000h to 01Fh
USCI_B1 (see Table 9-42)
0620h
000h to 01Fh
USCI_A2 (see Table 9-39)
0640h
000h to 01Fh
USCI_B2 (see Table 9-40)
0660h
000h to 01Fh
USCI_A3 (see Table 9-41)
0680h
000h to 01Fh
USCI_B3 (see Table 9-42)
06A0h
000h to 01Fh
ADC10_A (see Table 9-47)
0740h
000h to 01Fh
Comparator_B (see Table 9-48)
08C0h
000h to 00Fh
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
65
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-17. Special Function Registers (Base Address: 0100h)
REGISTER DESCRIPTION
REGISTER
OFFSET
SFR interrupt enable
SFRIE1
00h
SFR interrupt flag
SFRIFG1
02h
SFR reset pin control
SFRRPCR
04h
Table 9-18. PMM Registers (Base Address: 0120h)
REGISTER DESCRIPTION
REGISTER
OFFSET
PMM control 0
PMMCTL0
00h
PMM control 1
PMMCTL1
02h
SVS high-side control
SVSMHCTL
04h
SVS low-side control
SVSMLCTL
06h
PMM interrupt flags
PMMIFG
0Ch
PMM interrupt enable
PMMIE
0Eh
PMM power mode 5 control
PM5CTL0
10h
Table 9-19. Flash Control Registers (Base Address: 0140h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Flash control 1
FCTL1
00h
Flash control 3
FCTL3
04h
Flash control 4
FCTL4
06h
Table 9-20. CRC16 Registers (Base Address: 0150h)
REGISTER DESCRIPTION
REGISTER
OFFSET
CRC data input
CRC16DI
00h
CRC data input reverse byte
CRCDIRB
02h
CRC initialization and result
CRCINIRES
04h
CRC result reverse byte
CRCRESR
06h
Table 9-21. RAM Control Registers (Base Address: 0158h)
REGISTER DESCRIPTION
RAM control 0
REGISTER
RCCTL0
OFFSET
00h
Table 9-22. Watchdog Registers (Base Address: 015Ch)
REGISTER DESCRIPTION
Watchdog timer control
66
Submit Document Feedback
REGISTER
WDTCTL
OFFSET
00h
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-23. UCS Registers (Base Address: 0160h)
REGISTER DESCRIPTION
REGISTER
OFFSET
UCS control 0
UCSCTL0
00h
UCS control 1
UCSCTL1
02h
UCS control 2
UCSCTL2
04h
UCS control 3
UCSCTL3
06h
UCS control 4
UCSCTL4
08h
UCS control 5
UCSCTL5
0Ah
UCS control 6
UCSCTL6
0Ch
UCS control 7
UCSCTL7
0Eh
UCS control 8
UCSCTL8
10h
UCS control 9
UCSCTL9
12h
Table 9-24. SYS Registers (Base Address: 0180h)
REGISTER DESCRIPTION
REGISTER
OFFSET
System control
SYSCTL
00h
Bootloader configuration area
SYSBSLC
02h
JTAG mailbox control
SYSJMBC
06h
JTAG mailbox input 0
SYSJMBI0
08h
JTAG mailbox input 1
SYSJMBI1
0Ah
JTAG mailbox output 0
SYSJMBO0
0Ch
JTAG mailbox output 1
SYSJMBO1
0Eh
User NMI vector generator
SYSUNIV
1Ah
System NMI vector generator
SYSSNIV
1Ch
Reset vector generator
SYSRSTIV
1Eh
Table 9-25. Shared Reference Registers (Base Address: 01B0h)
REGISTER DESCRIPTION
Shared reference control
REGISTER
OFFSET
REFCTL
00h
Table 9-26. Port Mapping Registers
(Base Address of Port Mapping Control: 01C0h, Port P4: 01E0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port mapping key/ID
PMAPKEYID
00h
Port mapping control
PMAPCTL
02h
Port P4.0 mapping
P4MAP0
00h
Port P4.1 mapping
P4MAP1
01h
Port P4.2 mapping
P4MAP2
02h
Port P4.3 mapping
P4MAP3
03h
Port P4.4 mapping
P4MAP4
04h
Port P4.5 mapping
P4MAP5
05h
Port P4.6 mapping
P4MAP6
06h
Port P4.7 mapping
P4MAP7
07h
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
67
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-27. Port P1, P2 Registers (Base Address: 0200h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P1 input
P1IN
00h
Port P1 output
P1OUT
02h
Port P1 direction
P1DIR
04h
Port P1 resistor enable
P1REN
06h
Port P1 drive strength
P1DS
08h
Port P1 selection
P1SEL
0Ah
Port P1 interrupt vector word
P1IV
0Eh
Port P1 interrupt edge select
P1IES
18h
Port P1 interrupt enable
P1IE
1Ah
Port P1 interrupt flag
P1IFG
1Ch
Port P2 input
P2IN
01h
Port P2 output
P2OUT
03h
Port P2 direction
P2DIR
05h
Port P2 resistor enable
P2REN
07h
Port P2 drive strength
P2DS
09h
Port P2 selection
P2SEL
0Bh
Port P2 interrupt vector word
P2IV
1Eh
Port P2 interrupt edge select
P2IES
19h
Port P2 interrupt enable
P2IE
1Bh
Port P2 interrupt flag
P2IFG
1Dh
Table 9-28. Port P3, P4 Registers (Base Address: 0220h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P3 input
P3IN
00h
Port P3 output
P3OUT
02h
Port P3 direction
P3DIR
04h
Port P3 resistor enable
P3REN
06h
Port P3 drive strength
P3DS
08h
Port P3 selection
P3SEL
0Ah
Port P4 input
P4IN
01h
Port P4 output
P4OUT
03h
Port P4 direction
P4DIR
05h
Port P4 resistor enable
P4REN
07h
Port P4 drive strength
P4DS
09h
Port P4 selection
P4SEL
0Bh
68
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-29. Port P5, P6 Registers (Base Address: 0240h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P5 input
P5IN
00h
Port P5 output
P5OUT
02h
Port P5 direction
P5DIR
04h
Port P5 resistor enable
P5REN
06h
Port P5 drive strength
P5DS
08h
Port P5 selection
P5SEL
0Ah
Port P6 input
P6IN
01h
Port P6 output
P6OUT
03h
Port P6 direction
P6DIR
05h
Port P6 resistor enable
P6REN
07h
Port P6 drive strength
P6DS
09h
Port P6 selection
P6SEL
0Bh
Port P6 interrupt vector word
P6IV
1Eh
Port P6 interrupt edge select
P6IES
19h
Port P6 interrupt enable
P6IE
1Bh
Port P6 interrupt flag
P6IFG
1Dh
Table 9-30. Port P7 Registers (Base Address: 0260h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P7 input
P7IN
00h
Port P7 output
P7OUT
02h
Port P7 direction
P7DIR
04h
Port P7 resistor enable
P7REN
06h
Port P7 drive strength
P7DS
08h
Port P7 selection
P7SEL
0Ah
Table 9-31. Port J Registers (Base Address: 0320h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port PJ input
PJIN
00h
Port PJ output
PJOUT
02h
Port PJ direction
PJDIR
04h
Port PJ resistor enable
PJREN
06h
Port PJ drive strength
PJDS
08h
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
69
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-32. TA0 Registers (Base Address: 0340h)
REGISTER DESCRIPTION
REGISTER
OFFSET
TA0 control
TA0CTL
00h
Capture/compare control 0
TA0CCTL0
02h
Capture/compare control 1
TA0CCTL1
04h
Capture/compare control 2
TA0CCTL2
06h
Capture/compare control 3
TA0CCTL3
08h
Capture/compare control 4
TA0CCTL4
0Ah
TA0 counter
TA0R
10h
Capture/compare 0
TA0CCR0
12h
Capture/compare 1
TA0CCR1
14h
Capture/compare 2
TA0CCR2
16h
Capture/compare 3
TA0CCR3
18h
Capture/compare 4
TA0CCR4
1Ah
TA0 expansion 0
TA0EX0
20h
TA0 interrupt vector
TA0IV
2Eh
Table 9-33. TA1 Registers (Base Address: 0380h)
REGISTER DESCRIPTION
REGISTER
OFFSET
TA1 control
TA1CTL
00h
Capture/compare control 0
TA1CCTL0
02h
Capture/compare control 1
TA1CCTL1
04h
Capture/compare control 2
TA1CCTL2
06h
TA1 counter
TA1R
10h
Capture/compare 0
TA1CCR0
12h
Capture/compare 1
TA1CCR1
14h
Capture/compare 2
TA1CCR2
16h
TA1 expansion 0
TA1EX0
20h
TA1 interrupt vector
TA1IV
2Eh
70
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-34. TB0 Registers (Base Address: 03C0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
TB0 control
TB0CTL
00h
Capture/compare control 0
TB0CCTL0
02h
Capture/compare control 1
TB0CCTL1
04h
Capture/compare control 2
TB0CCTL2
06h
Capture/compare control 3
TB0CCTL3
08h
Capture/compare control 4
TB0CCTL4
0Ah
Capture/compare control 5
TB0CCTL5
0Ch
Capture/compare control 6
TB0CCTL6
0Eh
TB0 counter
TB0R
10h
Capture/compare 0
TB0CCR0
12h
Capture/compare 1
TB0CCR1
14h
Capture/compare 2
TB0CCR2
16h
Capture/compare 3
TB0CCR3
18h
Capture/compare 4
TB0CCR4
1Ah
Capture/compare 5
TB0CCR5
1Ch
Capture/compare 6
TB0CCR6
1Eh
TB0 expansion 0
TB0EX0
20h
TB0 interrupt vector
TB0IV
2Eh
Table 9-35. TA2 Registers (Base Address: 0400h)
REGISTER DESCRIPTION
REGISTER
OFFSET
TA2 control
TA2CTL
00h
Capture/compare control 0
TA2CCTL0
02h
Capture/compare control 1
TA2CCTL1
04h
Capture/compare control 2
TA2CCTL2
06h
TA2 counter
TA2R
10h
Capture/compare 0
TA2CCR0
12h
Capture/compare 1
TA2CCR1
14h
Capture/compare 2
TA2CCR2
16h
TA2 expansion 0
TA2EX0
20h
TA2 interrupt vector
TA2IV
2Eh
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
71
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-36. Real-Time Clock Registers (Base Address: 04A0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
RTC control 0
RTCCTL0
00h
RTC control 1
RTCCTL1
01h
RTC control 2
RTCCTL2
02h
RTC control 3
RTCCTL3
03h
RTC prescaler 0 control
RTCPS0CTL
08h
RTC prescaler 1 control
RTCPS1CTL
0Ah
RTC prescaler 0
RTCPS0
0Ch
RTC prescaler 1
RTCPS1
0Dh
RTC interrupt vector word
RTCIV
0Eh
RTC seconds/counter 1
RTCSEC/RTCNT1
10h
RTC minutes/counter 2
RTCMIN/RTCNT2
11h
RTC hours/counter 3
RTCHOUR/RTCNT3
12h
RTC day of week/counter 4
RTCDOW/RTCNT4
13h
RTC days
RTCDAY
14h
RTC month
RTCMON
15h
RTC year low
RTCYEARL
16h
RTC year high
RTCYEARH
17h
RTC alarm minutes
RTCAMIN
18h
RTC alarm hours
RTCAHOUR
19h
RTC alarm day of week
RTCADOW
1Ah
RTC alarm days
RTCADAY
1Bh
72
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-37. 32-Bit Hardware Multiplier Registers (Base Address: 04C0h)
REGISTER DESCRIPTION
16-bit operand 1 – multiply
REGISTER
MPY
OFFSET
00h
16-bit operand 1 – signed multiply
MPYS
02h
16-bit operand 1 – multiply accumulate
MAC
04h
16-bit operand 1 – signed multiply accumulate
MACS
06h
16-bit operand 2
OP2
08h
16 × 16 result low word
RESLO
0Ah
16 × 16 result high word
RESHI
0Ch
16 × 16 sum extension
SUMEXT
0Eh
32-bit operand 1 – multiply low word
MPY32L
10h
32-bit operand 1 – multiply high word
MPY32H
12h
32-bit operand 1 – signed multiply low word
MPYS32L
14h
32-bit operand 1 – signed multiply high word
MPYS32H
16h
32-bit operand 1 – multiply accumulate low word
MAC32L
18h
32-bit operand 1 – multiply accumulate high word
MAC32H
1Ah
32-bit operand 1 – signed multiply accumulate low word
MACS32L
1Ch
32-bit operand 1 – signed multiply accumulate high word
MACS32H
1Eh
32-bit operand 2 – low word
OP2L
20h
32-bit operand 2 – high word
OP2H
22h
32 × 32 result 0 – least significant word
RES0
24h
32 × 32 result 1
RES1
26h
32 × 32 result 2
RES2
28h
32 × 32 result 3 – most significant word
RES3
2Ah
MPY32 control 0
MPY32CTL0
2Ch
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
73
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-38. DMA Registers (Base Address DMA General Control: 0500h,
DMA Channel 0: 0510h, DMA Channel 1: 0520h, DMA Channel 2: 0530h)
REGISTER DESCRIPTION
REGISTER
OFFSET
DMA channel 0 control
DMA0CTL
00h
DMA channel 0 source address low
DMA0SAL
02h
DMA channel 0 source address high
DMA0SAH
04h
DMA channel 0 destination address low
DMA0DAL
06h
DMA channel 0 destination address high
DMA0DAH
08h
DMA channel 0 transfer size
DMA0SZ
0Ah
DMA channel 1 control
DMA1CTL
00h
DMA channel 1 source address low
DMA1SAL
02h
DMA channel 1 source address high
DMA1SAH
04h
DMA channel 1 destination address low
DMA1DAL
06h
DMA channel 1 destination address high
DMA1DAH
08h
DMA channel 1 transfer size
DMA1SZ
0Ah
DMA channel 2 control
DMA2CTL
00h
DMA channel 2 source address low
DMA2SAL
02h
DMA channel 2 source address high
DMA2SAH
04h
DMA channel 2 destination address low
DMA2DAL
06h
DMA channel 2 destination address high
DMA2DAH
08h
DMA channel 2 transfer size
DMA2SZ
0Ah
DMA module control 0
DMACTL0
00h
DMA module control 1
DMACTL1
02h
DMA module control 2
DMACTL2
04h
DMA module control 3
DMACTL3
06h
DMA module control 4
DMACTL4
08h
DMA interrupt vector
DMAIV
0Eh
Table 9-39. USCI_A0 Registers (Base Address: 05C0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
USCI control 1
UCA0CTL1
00h
USCI control 0
UCA0CTL0
01h
USCI baud rate 0
UCA0BR0
06h
USCI baud rate 1
UCA0BR1
07h
USCI modulation control
UCA0MCTL
08h
USCI status
UCA0STAT
0Ah
USCI receive buffer
UCA0RXBUF
0Ch
USCI transmit buffer
UCA0TXBUF
0Eh
USCI LIN control
UCA0ABCTL
10h
USCI IrDA transmit control
UCA0IRTCTL
12h
USCI IrDA receive control
UCA0IRRCTL
13h
USCI interrupt enable
UCA0IE
1Ch
USCI interrupt flags
UCA0IFG
1Dh
USCI interrupt vector word
UCA0IV
1Eh
74
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-40. USCI_B0 Registers (Base Address: 05E0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
USCI synchronous control 1
UCB0CTL1
00h
USCI synchronous control 0
UCB0CTL0
01h
USCI synchronous bit rate 0
UCB0BR0
06h
USCI synchronous bit rate 1
UCB0BR1
07h
USCI synchronous status
UCB0STAT
0Ah
USCI synchronous receive buffer
UCB0RXBUF
0Ch
USCI synchronous transmit buffer
UCB0TXBUF
0Eh
USCI I2C own address
UCB0I2COA
10h
USCI I2C slave address
UCB0I2CSA
12h
USCI interrupt enable
UCB0IE
1Ch
USCI interrupt flags
UCB0IFG
1Dh
USCI interrupt vector word
UCB0IV
1Eh
Table 9-41. USCI_A1 Registers (Base Address: 0600h)
REGISTER DESCRIPTION
REGISTER
OFFSET
USCI control 1
UCA1CTL1
00h
USCI control 0
UCA1CTL0
01h
USCI baud rate 0
UCA1BR0
06h
USCI baud rate 1
UCA1BR1
07h
USCI modulation control
UCA1MCTL
08h
USCI status
UCA1STAT
0Ah
USCI receive buffer
UCA1RXBUF
0Ch
USCI transmit buffer
UCA1TXBUF
0Eh
USCI LIN control
UCA1ABCTL
10h
USCI IrDA transmit control
UCA1IRTCTL
12h
USCI IrDA receive control
UCA1IRRCTL
13h
USCI interrupt enable
UCA1IE
1Ch
USCI interrupt flags
UCA1IFG
1Dh
USCI interrupt vector word
UCA1IV
1Eh
Table 9-42. USCI_B1 Registers (Base Address: 0620h)
REGISTER DESCRIPTION
REGISTER
OFFSET
USCI synchronous control 1
UCB1CTL1
00h
USCI synchronous control 0
UCB1CTL0
01h
USCI synchronous bit rate 0
UCB1BR0
06h
USCI synchronous bit rate 1
UCB1BR1
07h
USCI synchronous status
UCB1STAT
0Ah
USCI synchronous receive buffer
UCB1RXBUF
0Ch
USCI synchronous transmit buffer
UCB1TXBUF
0Eh
USCI I2C own address
UCB1I2COA
10h
USCI I2C slave address
UCB1I2CSA
12h
USCI interrupt enable
UCB1IE
1Ch
USCI interrupt flags
UCB1IFG
1Dh
USCI interrupt vector word
UCB1IV
1Eh
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
75
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-43. USCI_A2 Registers (Base Address: 0640h)
REGISTER DESCRIPTION
REGISTER
OFFSET
USCI control 1
UCA2CTL1
00h
USCI control 0
UCA2CTL0
01h
USCI baud rate 0
UCA2BR0
06h
USCI baud rate 1
UCA2BR1
07h
USCI modulation control
UCA2MCTL
08h
USCI status
UCA2STAT
0Ah
USCI receive buffer
UCA2RXBUF
0Ch
USCI transmit buffer
UCA2TXBUF
0Eh
USCI LIN control
UCA2ABCTL
10h
USCI IrDA transmit control
UCA2IRTCTL
12h
USCI IrDA receive control
UCA2IRRCTL
13h
USCI interrupt enable
UCA2IE
1Ch
USCI interrupt flags
UCA2IFG
1Dh
USCI interrupt vector word
UCA2IV
1Eh
Table 9-44. USCI_B2 Registers (Base Address: 0660h)
REGISTER DESCRIPTION
REGISTER
OFFSET
USCI synchronous control 1
UCB2CTL1
00h
USCI synchronous control 0
UCB2CTL0
01h
USCI synchronous bit rate 0
UCB2BR0
06h
USCI synchronous bit rate 1
UCB2BR1
07h
USCI synchronous status
UCB2STAT
0Ah
USCI synchronous receive buffer
UCB2RXBUF
0Ch
USCI synchronous transmit buffer
UCB2TXBUF
0Eh
USCI I2C own address
UCB2I2COA
10h
USCI I2C slave address
UCB2I2CSA
12h
USCI interrupt enable
UCB2IE
1Ch
USCI interrupt flags
UCB2IFG
1Dh
USCI interrupt vector word
UCB2IV
1Eh
Table 9-45. USCI_A3 Registers (Base Address: 0680h)
REGISTER DESCRIPTION
REGISTER
OFFSET
USCI control 1
UCA3CTL1
00h
USCI control 0
UCA3CTL0
01h
USCI baud rate 0
UCA3BR0
06h
USCI baud rate 1
UCA3BR1
07h
USCI modulation control
UCA3MCTL
08h
USCI status
UCA3STAT
0Ah
USCI receive buffer
UCA3RXBUF
0Ch
USCI transmit buffer
UCA3TXBUF
0Eh
USCI LIN control
UCA3ABCTL
10h
USCI IrDA transmit control
UCA3IRTCTL
12h
USCI IrDA receive control
UCA3IRRCTL
13h
USCI interrupt enable
UCA3IE
1Ch
USCI interrupt flags
UCA3IFG
1Dh
USCI interrupt vector word
UCA3IV
1Eh
76
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-46. USCI_B3 Registers (Base Address: 06A0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
USCI synchronous control 1
UCB3CTL1
00h
USCI synchronous control 0
UCB3CTL0
01h
USCI synchronous bit rate 0
UCB3BR0
06h
USCI synchronous bit rate 1
UCB3BR1
07h
USCI synchronous status
UCB3STAT
0Ah
USCI synchronous receive buffer
UCB3RXBUF
0Ch
USCI synchronous transmit buffer
UCB3TXBUF
0Eh
USCI I2C own address
UCB3I2COA
10h
USCI I2C slave address
UCB3I2CSA
12h
USCI interrupt enable
UCB3IE
1Ch
USCI interrupt flags
UCB3IFG
1Dh
USCI interrupt vector word
UCB3IV
1Eh
Table 9-47. ADC10_A Registers (Base Address: 0740h)
REGISTER DESCRIPTION
REGISTER
OFFSET
ADC10_A control 0
ADC10CTL0
00h
ADC10_A control 1
ADC10CTL1
02h
ADC10_A control 2
ADC10CTL2
04h
ADC10_A window comparator low threshold
ADC10LO
06h
ADC10_A window comparator high threshold
ADC10HI
08h
ADC10_A memory control 0
ADC10MCTL0
0Ah
ADC10_A conversion memory
ADC10MEM0
12h
ADC10_A interrupt enable
ADC10IE
1Ah
ADC10_A interrupt flags
ADC10IGH
1Ch
ADC10_A interrupt vector word
ADC10IV
1Eh
Table 9-48. Comparator_B Registers (Base Address: 08C0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Comp_B control 0
CBCTL0
00h
Comp_B control 1
CBCTL1
02h
Comp_B control 2
CBCTL2
04h
Comp_B control 3
CBCTL3
06h
Comp_B interrupt
CBINT
0Ch
Comp_B interrupt vector word
CBIV
0Eh
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
77
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10 Input/Output Diagrams
9.10.1 Port P1 (P1.0 to P1.7) Input/Output With Schmitt Trigger
Figure 9-2 shows the port diagram. Table 9-49 summarizes the selection of the pin function.
Pad Logic
P1REN.x
P1DIR.x
0
From module
1
P1OUT.x
0
From module
1
DVSS
0
DVIO
1
1
Direction
0: Input
1: Output
P1DS.x
0: Low drive
1: High drive
P1SEL.x
P1IN.x
EN
To module
P1.0/TA0CLK/ACLK
P1.1/TA0.0
P1.2/TA0.1
P1.3/TA0.2
P1.4/TA0.3
P1.5/TA0.4
P1.6/TA1CLK/CBOUT
P1.7/TA1.0
D
P1IE.x
EN
P1IRQ.x
Q
P1IFG.x
P1SEL.x
P1IES.x
Set
Interrupt
Edge
Select
Figure 9-2. Port P1 (P1.0 to P1.7) Diagram
78
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-49. Port P1 (P1.0 to P1.7) Pin Functions
PIN NAME (P1.x)
x
FUNCTION
P1.0 (I/O)
P1.0/TA0CLK/ACLK
0
TA0CLK
ACLK
P1.1 (I/O)
P1.1/TA0.0
1
2
4
TA0.CCI1A
6
I: 0; O: 1
0
0
1
1
1
I: 0; O: 1
0
0
1
1
1
I: 0; O: 1
0
0
1
TA0.CCI3A
1
1
I: 0; O: 1
0
TA0.CCI4A
0
1
TA0.4
1
1
I: 0; O: 1
0
0
1
TA1CLK
CBOUT comparator B
7
0
TA0.2
1
1
I: 0; O: 1
0
TA1.CCI0A
0
1
TA1.0
1
1
P1.7 (I/O)
P1.7/TA1.0
1
TA0.CCI2A
P1.6 (I/O)
P1.6/TA1CLK/CBOUT
1
I: 0; O: 1
1
TA0.3
5
1
1
P1.5 (I/O)
P1.5/TA0.4
0
0
0
P1.4 (I/O)
P1.4/TA0.3
I: 0; O: 1
1
TA0.1
3
P1SEL.x
TA0.0
P1.3 (I/O)
P1.3/TA0.2
P1DIR.x
TA0.CCI0A
P1.2 (I/O)
P1.2/TA0.1
CONTROL BITS OR SIGNALS
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
79
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.2 Port P2 (P2.0 to P2.7) Input/Output With Schmitt Trigger
Figure 9-3 shows the port diagram. Table 9-50 summarizes the selection of the pin function.
Pad Logic
P2REN.x
P2DIR.x
0
From module
1
P2OUT.x
0
From module
1
DVSS
0
DVIO
1
Direction
0: Input
1: Output
P2DS.x
0: Low drive
1: High drive
P2SEL.x
P2IN.x
EN
To module
1
P2.0/TA1.1
P2.1/TA1.2
P2.2/UCB3SIMO/UCB3SDA
P2.3/UCB3SOMI/UCB3SCL
P2.4/UCB3CLK/UCA3STE
P2.5/UCB3STE/UCA3CLK
P2.6/RTCCLK/DMAE0
P2.7/UB0STE/UCA0CLK
D
P2IE.x
EN
To module
Q
P2IFG.x
P2SEL.x
P2IES.x
Set
Interrupt
Edge
Select
Figure 9-3. Port P2 (P2.0 to P2.7) Diagram
80
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-50. Port P2 (P2.0 to P2.7) Pin Functions
PIN NAME (P2.x)
x
FUNCTION
P2.0 (I/O)
P2.0/TA1.1
0
TA1.CCI1A
TA1.1
P2.1 (I/O)
P2.1/TA1.2
1
P2.2/UCB3SIMO/UCB3SDA
2
P2.3/UCB3SOMI/UCB3SCL
3
P2.4/UCB3CLK/UCA3STE
4
P2.5/UCB3STE/UCA3CLK
5
P2.6/RTCCLK/DMAE0
6
(1)
(2)
(3)
(4)
(5)
7
P2DIR.x
P2SEL.x
I: 0; O: 1
0
0
1
1
1
I: 0; O: 1
0
TA1.CCI2A
0
1
TA1.2
1
1
P2.2 (I/O)
UCB3SIMO/UCB3SDA
P2.3 (I/O)
UCB3SOMI/UCB3SCL
P2.4 (I/O)
UCB3CLK/UCA3STE(2) (3)
P2.5 (I/O)
UCB3STE/UCA3CLK(2) (4)
P2.6 (I/O)
P2.7/UCB0STE/UCA0CLK
CONTROL BITS OR SIGNALS(1)
DMAE0
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
0
1
RTCCLK
1
1
P2.7 (I/O)
I: 0; O: 1
0
X
1
UCB0STE/UCA0CLK(2) (5)
X = Don't care
The pin direction is controlled by the USCI module.
UCB3CLK function takes precedence over UCA3STE function. If the pin is required as UCB3CLK input or output, USCI A3 is forced to
3-wire SPI mode if 4-wire SPI mode is selected.
UCA3CLK function takes precedence over UCB3STE function. If the pin is required as UCA3CLK input or output, USCI_B3 is forced to
3-wire SPI mode if 4-wire SPI mode is selected.
UCA0CLK function takes precedence over UCB0STE function. If the pin is required as UCA0CLK input or output, USCI_B0 is forced to
3-wire SPI mode if 4-wire SPI mode is selected.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
81
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.3 Port P3 (P3.0 to P3.4) Input/Output With Schmitt Trigger
Figure 9-4 shows the port diagram. Table 9-51 summarizes the selection of the pin function.
Pad Logic
P3REN.x
P3DIR.x
0
From module
1
P3OUT.x
0
From module
1
DVSS
0
DVIO
1
1
Direction
0: Input
1: Output
P3.0/UCB0SIMO/UCB0SDA
P3.1/UCB0SOMI/UCB0SCL
P3.2/UCB0CLK/UCA0STE
P3.3/UCA0TXD/UCA0SIMO
P3.4/UCA0RXD/UCA0SOMI
P3DS.x
0: Low drive
1: High drive
P3SEL.x
P3IN.x
EN
D
To module
Figure 9-4. Port P3 (P3.0 to P3.4) Diagram
Table 9-51. Port P3 (P3.0 to P3.4) Pin Functions
PIN NAME (P3.x)
P3.0/UCB0SIMO/UCB0SDA
P3.1/UCB0SOMI/UCB0SCL
P3.2/UCB0CLK/UCA0STE
P3.3/UCA0TXD/UCA0SIMO
P3.4/UCA0RXD/UCA0SOMI
(1)
(2)
(3)
(4)
82
x
0
1
2
3
4
FUNCTION
P3.0 (I/O)
UCB0SIMO/UCB0SDA(2) (3)
P3.1 (I/O)
UCB0SOMI/UCB0SCL(2) (3)
P3.2 (I/O)
UCB0CLK/UCA0STE(2) (4)
P3.3 (I/O)
UCA0TXD/UCA0SIMO(2)
P3.4 (I/O)
UCA0RXD/UCA0SOMI(2)
CONTROL BITS OR SIGNALS(1)
P3DIR.x
P3SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
X = Don't care
The pin direction is controlled by the USCI module.
If the I2C functionality is selected, the output drives only the logical 0 to VSS level.
UCB0CLK function takes precedence over UCA0STE function. If the pin is required as UCB0CLK input or output, USCI_A0 is forced to
3-wire SPI mode if 4-wire SPI mode is selected.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.4 Port P4 (P4.0 to P4.7) Input/Output With Schmitt Trigger
Figure 9-5 shows the port diagram. Table 9-52 summarizes the selection of the pin function.
Pad Logic
P4REN.x
P4DIR.x
0
From Port Mapping Control
1
P4OUT.x
0
From Port Mapping Control
1
DVSS
0
DVIO
1
1
Direction
0: Input
1: Output
P4.0/P4MAP0
P4.1/P4MAP1
P4.2/P4MAP2
P4.3/P4MAP3
P4.4/P4MAP4
P4.5/P4MAP5
P4.6/P4MAP6
P4.7/P4MAP7
P4DS.x
0: Low drive
1: High drive
P4SEL.x
P4IN.x
EN
D
To Port Mapping Control
Figure 9-5. Port P4 (P4.0 to P4.7) Diagram
Table 9-52. Port P4 (P4.0 to P4.7) Pin Functions
PIN NAME (P4.x)
x
P4.0/P4MAP0
0
P4.1/P4MAP1
1
P4.2/P4MAP2
2
P4.3/P4MAP3
3
P4.4/P4MAP4
4
P4.5/P4MAP5
5
P4.6/P4MAP6
6
P4.7/P4MAP7
7
(1)
(2)
FUNCTION
P4.0 (I/O)
Mapped secondary digital function
P4.1 (I/O)
Mapped secondary digital function
P4.2 (I/O)
Mapped secondary digital function
P4.3 (I/O)
Mapped secondary digital function
P4.4 (I/O)
Mapped secondary digital function
P4.5 (I/O)
Mapped secondary digital function
P4.6 (I/O)
Mapped secondary digital function
P4.7 (I/O)
Mapped secondary digital function
CONTROL BITS OR SIGNALS(1)
P4DIR.x(2)
P4SEL.x
I: 0; O: 1
0
X
X
1
≤ 30
I: 0; O: 1
0
X
X
1
≤ 30
I: 0; O: 1
0
X
X
1
≤ 30
I: 0; O: 1
0
X
X
1
≤ 30
I: 0; O: 1
0
X
X
1
≤ 30
I: 0; O: 1
0
X
X
1
≤ 30
I: 0; O: 1
0
X
X
1
≤ 30
I: 0; O: 1
0
X
X
1
≤ 30
P4MAPx
X= Don't care
The direction of some mapped secondary functions are controlled directly by the module. See Table 9-8 for specific direction control
information of mapped secondary functions.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
83
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.5 Port P5 (P5.0 and P5.1) Input/Output With Schmitt Trigger
Figure 9-6 shows the port diagram. Table 9-53 summarizes the selection of the pin function.
To or from Reference
(1)
To ADC10
(1)
INCHx = x
(1)
Pad Logic
P5REN.x
P5DIR.x
DVSS
0
DVCC
1
1
0
1
P5OUT.x
0
From module
1
P5.0/(A8/VeREF+)
P5.1/(A9/VeREF–)
P5DS.x
0: Low drive
1: High drive
P5SEL.x
P5IN.x
Bus
Keeper
EN
To module
D
(1) not available for MSPF430F5258
MSPF430F5256
MSPF430F5254
MSPF430F5252
Figure 9-6. Port P5 (P5.0 and P5.1) Diagram
Table 9-53. Port P5 (P5.0 and P5.1) Pin Functions
PIN NAME (P5.x)
P5.0/A8/VeREF+
P5.1/A9/VeREF–
(1)
(2)
(3)
(4)
(5)
84
x
0
1
FUNCTION
P5.0
(I/O)(2)
A8/VeREF+(4)
P5.1
(I/O)(2)
A9/VeREF–(5)
CONTROL BITS OR SIGNALS(1)
P5DIR.x
P5SEL.x
REFOUT(3)
I: 0; O: 1
0
X
X
1
0
I: 0; O: 1
0
X
X
1
0
X = Don't care
Default condition
REFOUT resides in the REF module.
Setting the P5SEL.0 bit disables the output driver and the input Schmitt trigger to prevent parasitic cross currents when applying
analog signals. An external voltage can be applied to VeREF+ and used as the reference for the ADC10_A. Channel A8, when
selected with the INCHx bits, is connected to the VeREF+ pin.
Setting the P5SEL.1 bit disables the output driver and the input Schmitt trigger to prevent parasitic cross currents when applying
analog signals. An external voltage can be applied to VeREF- and used as the reference for the ADC10_A. Channel A9, when selected
with the INCHx bits, is connected to the VeREF- pin.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.6 Port P5 (P5.2 and P5.3) Input/Output With Schmitt Trigger
Figure 9-7 and Figure 9-8 show the port diagrams. Table 9-54 summarizes the selection of the pin function.
Pad Logic
To XT2
P5REN.2
P5DIR.2
DVSS
0
DVCC
1
1
0
1
P5OUT.2
0
Module X OUT
1
P5.2/XT2IN
P5DS.2
0: Low drive
1: High drive
P5SEL.2
P5IN.2
EN
Module X IN
Bus
Keeper
D
Figure 9-7. Port P5 (P5.2) Diagram
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
85
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Pad Logic
To XT2
P5REN.3
P5DIR.3
DVSS
0
DVCC
1
1
0
1
P5OUT.3
0
Module X OUT
1
P5SEL.2
P5.3/XT2OUT
P5DS.3
0: Low drive
1: High drive
XT2BYPASS
P5SEL.3
P5IN.3
Bus
Keeper
EN
Module X IN
D
Figure 9-8. Port P5 (P5.3) Diagram
Table 9-54. Port P5 (P5.2 and P5.3) Pin Functions
PIN NAME (P5.x)
x
FUNCTION
P5.2 (I/O)
P5.2/XT2IN
2 XT2IN crystal mode(2)
XT2IN bypass
mode(2)
P5.3 (I/O)
P5.3/XT2OUT
3 XT2OUT crystal mode(3)
P5.3 (I/O)(3)
(1)
(2)
(3)
86
CONTROL BITS OR SIGNALS(1)
P5DIR.x
P5SEL.2
P5SEL.3
XT2BYPASS
I: 0; O: 1
0
X
X
X
1
X
0
X
1
X
1
I: 0; O: 1
0
0
X
X
1
X
0
X
1
0
1
X = Don't care
Setting P5SEL.2 causes the general-purpose I/O to be disabled. Pending the setting of XT2BYPASS, P5.2 is configured for crystal
mode or bypass mode.
Setting P5SEL.2 causes the general-purpose I/O to be disabled in crystal mode. When using bypass mode, P5.3 can be used as
general-purpose I/O.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.7 Port P5 (P5.4 and P5.5) Input/Output With Schmitt Trigger
Figure 9-9 and Figure 9-10 show the port diagrams. Table 9-55 summarizes the selection of the pin function.
Pad Logic
to XT1
P5REN.4
P5DIR.4
DVSS
0
DVCC
1
1
0
1
P5OUT.4
0
Module X OUT
1
P5.4/XIN
P5DS.4
0: Low drive
1: High drive
P5SEL.4
P5IN.4
EN
Module X IN
Bus
Keeper
D
Figure 9-9. Port P5 (P5.4) Diagram
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
87
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Pad Logic
to XT1
P5REN.5
P5DIR.5
DVSS
0
DVCC
1
1
0
1
P5OUT.5
0
Module X OUT
1
P5.5/XOUT
P5SEL.4
P5DS.5
0: Low drive
1: High drive
XT1BYPASS
P5SEL.5
P5IN.5
Bus
Keeper
EN
Module X IN
D
Figure 9-10. Port P5 (P5.5) Diagram
Table 9-55. Port P5 (P5.4 and P5.5) Pin Functions
PIN NAME (P5.x)
x
FUNCTION
P5.4 (I/O)
P5.4/XIN
4 XIN crystal mode(2)
XIN bypass
mode(2)
P5.5 (I/O)
P5.5/XOUT
5 XOUT crystal mode(3)
P5.5 (I/O)(3)
(1)
(2)
(3)
88
CONTROL BITS OR SIGNALS(1)
P5DIR.x
P5SEL.4
P5SEL.5
XT1BYPASS
I: 0; O: 1
0
X
X
X
1
X
0
X
1
X
1
I: 0; O: 1
0
0
X
X
1
X
0
X
1
0
1
X = Don't care
Setting P5SEL.4 causes the general-purpose I/O to be disabled. Pending the setting of XT1BYPASS, P5.4 is configured for crystal
mode or bypass mode.
Setting P5SEL.4 causes the general-purpose I/O to be disabled in crystal mode. When using bypass mode, P5.5 can be used as
general-purpose I/O.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.8 Port P6 (P6.0 to P6.7) Input/Output With Schmitt Trigger
Figure 9-11 shows the port diagram. Table 9-56 summarizes the selection of the pin function.
Pad Logic
To ADC10
(1)
INCHx = x
(1)
To Comparator_B
From Comparator_B
CBPD.x
P6REN.x
P6DIR.x
0
0
From module
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P6OUT.x
DVSS
P6DS.x
0: Low drive
1: High drive
P6SEL.x
P6IN.x
Bus
Keeper
EN
To module
P6.0/TA2CLK/CB0/(A0)
P6.1/TA2.0/CB1/(A1)
P6.2/TA2.1/CB2/(A2)
P6.3/TA2.2/CB3/(A3)
P6.4/CB4/(A4)
P6.5/CB5/(A5)
P6.6/CB6/(A6)
P6.7/CB7/(A7)
D
P6IE.x
EN
P6IRQ.x
Q
P6IFG.x
Set
P6SEL.x
Interrupt
Edge
Select
P6IES.x
(1) not available for MSPF430F5258
MSPF430F5256
MSPF430F5254
MSPF430F5252
Figure 9-11. Port P6 (P6.0 to P6.7) Diagram
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
89
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-56. Port P6 (P6.0 to P6.7) Pin Functions
PIN NAME (P6.x)
x
FUNCTION
P6.0 (I/O)
TA2CLK
P6.0/TA2CLK/SMCLK/CB0/(A0)
0 SMCLK
A0
CB0(1)
P6.1 (I/O)
TA2.CCI0A
P6.1/TA2.0/CB1/(A1)
1
0
X
1
X
X
1
I: 0; O: 1
0
0
A1
X
X
1
CB1(1)
X
X
1
I: 0; O: 1
0
0
0
1
0
2 TA2.1
1
1
0
A2
X
X
1
X
X
1
I: 0; O: 1
0
0
0
1
0
3 TA2.2
1
1
0
A3
X
X
1
CB3(1)
X
X
1
I: 0; O: 1
0
0
X
X
1
CB4(1)
P6.5 (I/O)
5 A5
CB5(1)
P6.6 (I/O)
6 A6
CB6(1)
P6.7 (I/O)
7 A7
CB7(1)
90
1
X
0
P6.4 (I/O)
(1)
0
0
4 A4
P6.7/CB7/(A7)
0
1
1
TA2.CCI2A
P6.6/CB6/(A6)
0
0
1
P6.3 (I/O)
P6.5/CB5/(A5)
I: 0; O: 1
1
CB2(1)
P6.4/CB4/(A4)
CBPD
0
TA2.CCI1A
P6.3/TA2.1/CB3/(A3)
P6SEL.x
1 TA2.0
P6.2 (I/O)
P6.2/TA2.1/CB2/(A2)
CONTROL BITS OR SIGNALS
P6DIR.x
X
X
1
I: 0; O: 1
0
0
X
X
1
X
X
1
I: 0; O: 1
0
0
X
X
1
X
X
1
I: 0; O: 1
0
0
X
X
1
X
X
1
Setting the CBPD.x bit disables the output driver and the input Schmitt trigger to prevent parasitic cross currents when applying analog
signals. Selecting the CBx input pin to the comparator multiplexer with the CBx bits automatically disables output driver and input
buffer for that pin, regardless of the state of the associated CBPD.x bit.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.9 Port P7 (P7.0 to P7.5) Input/Output With Schmitt Trigger
Figure 9-12 shows the port diagram. Table 9-57 summarizes the selection of the pin function.
Pad Logic
P7REN.x
P7DIR.x
0
From module
1
P7OUT.x
0
DVSS
0
DVIO
1
1
Direction
0: Input
1: Output
1
P7DS.x
0: Low drive
1: High drive
P7SEL.x
P7IN.x
P7.0/UCA2TXD/UCA2SIMO
P7.1/UCA2RXD/UCA2SOMI
P7.2/UCB2CLK/UCA2STE
P7.3/UCB2SIMO/UCB2SDA
P7.4/UCB2SOMI/UCB2SCL
P7.5/UCB2STE/UCA2CLK
EN
D
To module
Figure 9-12. Port P7 (P7.0 to P7.5) Diagram
Table 9-57. Port P7 (P7.0 to P7.5) Pin Functions
PIN NAME (P7.x)
P7.0/UCA2TXD/UCA2SIMO(2)
P7.1/UCA2RXD/UCA2SOMI(2)
P7.2/UCB2CLK/UCA2STE(2)
P7.3/UCB2SIMO/UCB2SDA(2)
P7.4/UCB2SOMI/UCB2SCL(2)
P7.5/UCB2STE/UCA2CLK(2)
(1)
(2)
(3)
(4)
x
0
1
2
3
4
5
FUNCTION
P7.0 (I/O)
UCA2TXD/UCA2SIMO(1)
P7.1 (I/O)
UCA2RXD/UCA2SOMI(1)
P7.2 (I/O)
UCB2CLK/UCA2STE(1) (3)
P7.3 (I/O)
UCB2SIMO/UCB2SDA(1) (4)
P7.4 (I/O)
UCB2SOMI/UCB2SCL(1) (4)
P7.5 (I/O)
UCB2STE/UCA2CLK(1)
CONTROL BITS OR SIGNALS
P7DIR.x
P7SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
Setting P7SEL.x bit disables the output driver and the input Schmitt trigger.
The pin direction is controlled by the USCI module.
UCB2CLK function takes precedence over UCA2STE function. If the pin is required as UCB2CLK input or output, USCI_A2 is forced to
3-wire SPI mode if 4-wire SPI mode is selected.
If the I2C functionality is selected, the output drives only the logical 0 to VSS level.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
91
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.10 Port J (PJ.0) JTAG Pin TDO, Input/Output With Schmitt Trigger or Output
Figure 9-13 shows the port diagram. Table 9-58 summarizes the selection of the pin function.
Pad Logic
PJREN.0
PJDIR.0
0
DVCC
1
PJOUT.0
0
From JTAG
1
DVSS
0
DVCC
1
1
PJDS.0
0: Low drive
1: High drive
From JTAG
PJ.0/TDO
PJIN.0
EN
D
Figure 9-13. Port PJ (PJ.0) Diagram
92
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.10.11 Port J (PJ.1 to PJ.3) JTAG Pins TMS, TCK, TDI/TCLK, Input/Output With Schmitt Trigger or Output
Figure 9-14 shows the port diagram. Table 9-58 summarizes the selection of the pin function.
Pad Logic
PJREN.x
PJDIR.x
0
DVSS
1
PJOUT.x
0
From JTAG
1
DVSS
0
DVCC
1
1
PJ.1/TDI/TCLK
PJ.2/TMS
PJ.3/TCK
PJDS.x
0: Low drive
1: High drive
From JTAG
PJIN.x
EN
D
To JTAG
Figure 9-14. Port PJ (PJ.1 to PJ.3) Diagram
Table 9-58. Port PJ (PJ.0 to PJ.3) Pin Functions
PIN NAME (PJ.x)
x
CONTROL BITS
OR SIGNALS(1)
FUNCTION
PJDIR.x
PJ.0/TDO
PJ.1/TDI/TCLK
PJ.2/TMS
PJ.3/TCK
(1)
(2)
(3)
(4)
0
1
2
3
PJ.0 (I/O)(2)
I: 0; O: 1
TDO(3)
PJ.1
X
(I/O)(2)
I: 0; O: 1
TDI/TCLK(3) (4)
PJ.2
X
(I/O)(2)
I: 0; O: 1
TMS(3) (4)
PJ.3
X
(I/O)(2)
I: 0; O: 1
TCK(3) (4)
X
X = Don't care
Default condition
The pin direction is controlled by the JTAG module.
In JTAG mode, pullups are activated automatically on TMS, TCK, and TDI/TCLK. PJREN.x are don't care.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
93
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
9.11 Device Descriptors
Table 9-59 and Table 9-60 list the contents of the device descriptor tag-length-value (TLV) structure for each
device type.
Table 9-59. MSP430F5259, MSP430F5257, MSP430F5255, MSP430F5253 Device Descriptor Table
DESCRIPTION(1)
Info Block
Die Record
ADC10
Calibration
REF Calibration
(1)
94
VALUE
ADDRESS
SIZE
(bytes)
F5259
F5257
F5255
F5253
Info length
01A00h
1
06h
06h
06h
06h
CRC length
01A01h
1
06h
06h
06h
06h
CRC value
01A02h
2
Per unit
Per unit
Per unit
Per unit
Device ID
01A04h
1
FF
01
03
05
Device ID
01A05h
1
81
82
82
82
Hardware revision
01A06h
1
Per unit
Per unit
Per unit
Per unit
Firmware revision
01A07h
1
Per unit
Per unit
Per unit
Per unit
Die record tag
01A08h
1
08h
08h
08h
08h
Die record length
01A09h
1
0Ah
0Ah
0Ah
0Ah
Lot/wafer ID
01A0Ah
4
Per unit
Per unit
Per unit
Per unit
Die X position
01A0Eh
2
Per unit
Per unit
Per unit
Per unit
Die Y position
01A10h
2
Per unit
Per unit
Per unit
Per unit
Test results
01A12h
2
Per unit
Per unit
Per unit
Per unit
ADC10 calibration tag
01A14h
1
13h
13h
13h
13h
ADC10 calibration length
01A15h
1
10h
10h
10h
10h
ADC gain factor
01A16h
2
Per unit
Per unit
Per unit
Per unit
ADC offset
01A18h
2
Per unit
Per unit
Per unit
Per unit
ADC 1.5-V reference
Temperature sensor 30°C
01A1Ah
2
Per unit
Per unit
Per unit
Per unit
ADC 1.5-V reference
Temperature sensor 85°C
01A1Ch
2
Per unit
Per unit
Per unit
Per unit
ADC 2.0-V reference
Temperature sensor 30°C
01A1Eh
2
Per unit
Per unit
Per unit
Per unit
ADC 2.0-V reference
Temperature sensor 85°C
01A20h
2
Per unit
Per unit
Per unit
Per unit
ADC 2.5-V reference
Temperature sensor 30°C
01A22h
2
Per unit
Per unit
Per unit
Per unit
ADC 2.5-V reference
Temperature sensor 85°C
01A24h
2
Per unit
Per unit
Per unit
Per unit
REF calibration tag
01A26h
1
12h
12h
12h
12h
REF calibration length
01A27h
1
06h
06h
06h
06h
REF 1.5-V reference factor
01A28h
2
Per unit
Per unit
Per unit
Per unit
REF 2.0-V reference factor
01A2Ah
2
Per unit
Per unit
Per unit
Per unit
REF 2.5-V reference factor
01A2Ch
2
Per unit
Per unit
Per unit
Per unit
NA = Not applicable, blank = unused and reads FFh.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
Table 9-60. MSP430F5258, MSP430F5256, MSP430F5254, MSP430F5252 Device Descriptor Table
DESCRIPTION(1)
Info Block
Die Record
ADC10
Calibration
REF Calibration
(1)
VALUE
ADDRESS
SIZE
(bytes)
F5258
F5256
F5254
F5252
Info length
01A00h
1
06h
06h
06h
06h
CRC length
01A01h
1
06h
06h
06h
06h
CRC value
01A02h
2
Per unit
Per unit
Per unit
Per unit
Device ID
01A04h
1
00
02
04
06
Device ID
01A05h
1
82
82
82
82
Hardware revision
01A06h
1
Per unit
Per unit
Per unit
Per unit
Firmware revision
01A07h
1
Per unit
Per unit
Per unit
Per unit
Die record tag
01A08h
1
08h
08h
08h
08h
Die record length
01A09h
1
0Ah
0Ah
0Ah
0Ah
Lot/wafer ID
01A0Ah
4
Per unit
Per unit
Per unit
Per unit
Die X position
01A0Eh
2
Per unit
Per unit
Per unit
Per unit
Die Y position
01A10h
2
Per unit
Per unit
Per unit
Per unit
Test results
01A12h
2
Per unit
Per unit
Per unit
Per unit
ADC10 calibration tag
01A14h
1
13h
13h
13h
13h
ADC10 calibration length
01A15h
1
10h
10h
10h
10h
ADC gain factor
01A16h
2
blank
blank
blank
blank
ADC offset
01A18h
2
blank
blank
blank
blank
ADC 1.5-V reference
Temperature sensor 30°C
01A1Ah
2
blank
blank
blank
blank
ADC 1.5-V reference
Temperature sensor 85°C
01A1Ch
2
blank
blank
blank
blank
ADC 2.0-V reference
Temperature sensor 30°C
01A1Eh
2
blank
blank
blank
blank
ADC 2.0-V reference
Temperature sensor 85°C
01A20h
2
blank
blank
blank
blank
ADC 2.5-V reference
Temperature sensor 30°C
01A22h
2
blank
blank
blank
blank
ADC 2.5-V reference
Temperature sensor 85°C
01A24h
2
blank
blank
blank
blank
REF calibration tag
01A26h
1
12h
12h
12h
12h
REF calibration length
01A27h
1
06h
06h
06h
06h
REF 1.5-V reference factor
01A28h
2
Per unit
Per unit
Per unit
Per unit
REF 2.0-V reference factor
01A2Ah
2
Per unit
Per unit
Per unit
Per unit
REF 2.5-V reference factor
01A2Ch
2
Per unit
Per unit
Per unit
Per unit
NA = Not applicable, blank = unused and reads FFh.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
95
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
10 Device and Documentation Support
10.1 Getting Started and Next Steps
For more information on the MSP430™ family of devices and the tools and libraries that are available to help with
your development, visit the MSP430 ultra-low-power sensing and measurement MCUs overview.
10.2 Device Nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all MSP
MCU devices. Each MSP MCU commercial family member has one of two prefixes: MSP or XMS. These
prefixes represent evolutionary stages of product development from engineering prototypes (XMS) through fully
qualified production devices (MSP).
XMS – Experimental device that is not necessarily representative of the final device's electrical specifications
MSP – Fully qualified production device
XMS devices are shipped against the following disclaimer:
"Developmental product is intended for internal evaluation purposes."
MSP devices have been characterized fully, and the quality and reliability of the device have been demonstrated
fully. TI's standard warranty applies.
Predictions show that prototype devices (XMS) have a greater failure rate than the standard production devices.
TI recommends that these devices not be used in any production system because their expected end-use failure
rate still is undefined. Only qualified production devices are to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the temperature
range, package type, and distribution format. Figure 10-1 provides a legend for reading the complete device
name.
96
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
MSP 430 F 5 438 A I PM T -EP
Processor Family
Optional: Additional Features
MCU Platform
Optional: Tape and Reel
Device Type
Packaging
Series
Feature Set
Processor Family
MCU Platform
Optional: Temperature Range
Optional: Revision
CC = Embedded RF Radio
MSP = Mixed-Signal Processor
XMS = Experimental Silicon
PMS = Prototype Device
430 = MSP430 low-power microcontroller platform
Device Type
Memory Type
C = ROM
F = Flash
FR = FRAM
G = Flash
L = No nonvolatile memory
Specialized Application
AFE = Analog front end
BQ = Contactless power
CG = ROM medical
FE = Flash energy meter
FG = Flash medical
FW = Flash electronic flow meter
Series
1 = Up to 8 MHz
2 = Up to 16 MHz
3 = Legacy
4 = Up to 16 MHz with LCD driver
5 = Up to 25 MHz
6 = Up to 25 MHz with LCD driver
0 = Low-voltage series
Feature Set
Various levels of integration within a series
Optional: Revision
Updated version of the base part number
Optional: Temperature Range S = 0°C to 50°C
C = 0°C to 70°C
I = –40°C to 85°C
T = –40°C to 105°C
Packaging
http://www.ti.com/packaging
Optional: Tape and Reel
T = Small reel
R = Large reel
No markings = Tube or tray
Optional: Additional Features -EP = Enhanced product (–40°C to 105°C)
-HT = Extreme temperature parts (–55°C to 150°C)
-Q1 = Automotive Q100 qualified
Figure 10-1. Device Nomenclature
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
97
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
10.3 Tools and Software
All MSP microcontrollers are supported by a wide variety of software and hardware development tools. Tools are
available from TI and various third parties. See them all at MSP430 ultra-low-power MCUs – Tools & software.
Table 10-1 lists the debug features of the MSP430F522x MCUs. See the Code Composer Studio IDE for
MSP430 MCUs User's Guide for details on the available features.
Table 10-1. Hardware Debug Features
MSP430
ARCHITECTURE
4-WIRE
JTAG
2-WIRE
JTAG
BREAKPOINTS
(N)
RANGE
BREAKPOINTS
CLOCK
CONTROL
STATE
SEQUENCER
TRACE
BUFFER
LPMx.5
DEBUGGING
SUPPORT
MSP430Xv2
Yes
Yes
8
Yes
Yes
Yes
Yes
No
Design Kits and Evaluation Modules
64-pin target development board and MSP-FET programmer bundle for MSP430F5x MCUs
The MSP-FET430U64C is a powerful tool that includes the hardware and software required to complete much of
your application development work. The flash memory can be erased and programmed in seconds with only a
few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required.
64-pin target development board for MSP430F5x MCUs
The MSP-TS430RGC64C is a stand-alone 64-pin ZIF socket target board used to program and debug the
MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.
Dual-mode Bluetooth CC2564 module with integrated antenna evaluation board
The CC2564MODAEM evaluation board contains the Bluetooth BR/EDR/LE HCI solution. Based on TI's
CC2564B dual-mode Bluetooth single-chip device, the CC2564MODA is intended for evaluation and design
purposes, reducing design effort and enabling fast time to market.
Software
MSP430Ware™ Software
MSP430Ware software is a collection of code examples, data sheets, and other design resources for all
MSP430 devices delivered in a convenient package. In addition to providing a complete collection of existing
MSP430 MCU design resources, MSP430Ware software also includes a high-level API called MSP Driver
Library. This library makes it easy to program MSP430 hardware. MSP430Ware software is available as a
component of CCS or as a stand-alone package.
MSP430F525x Code Examples
C code examples that configure each of the integrated peripherals for various application needs.
MSP Driver Library
Driver Library's abstracted API keeps you above the bits and bytes of the MSP430 hardware by providing easyto-use function calls. Thorough documentation is delivered through a helpful API Guide, which includes details
on each function call and the recognized parameters. Developers can use Driver Library functions to write
complete projects with minimal overhead.
MSP EnergyTrace™ Technology
EnergyTrace technology for MSP430 microcontrollers is an energy-based code analysis tool that measures and
displays the application's energy profile and helps to optimize it for ultra-low-power consumption.
98
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
ULP (Ultra-Low Power) Advisor
ULP Advisor™ software is a tool for guiding developers to write more efficient code to fully utilize the unique
ultra-low power features of MSP and MSP432 microcontrollers. Aimed at both experienced and new
microcontroller developers, ULP Advisor checks your code against a thorough ULP checklist to squeeze every
last nano amp out of your application. At build time, ULP Advisor will provide notifications and remarks to
highlight areas of your code that can be further optimized for lower power.
IEC 60730 Software Package
The IEC 60730 MSP430 software package was developed to be useful in assisting customers in complying with
IEC 60730-1:2010 (Automatic Electrical Controls for Household and Similar Use – Part 1: General
Requirements) for up to Class B products, which includes home appliances, arc detectors, power converters,
power tools, e-bikes, and many others. The IEC 60730 MSP430 software package can be embedded in
customer applications running on MSP430s to help simplify the customer's certification efforts of functional
safety-compliant consumer devices to IEC 60730-1:2010 Class B.
Fixed Point Math Library for MSP
The MSP IQmath and Qmath Libraries are a collection of highly optimized and high-precision mathematical
functions for C programmers to seamlessly port a floating-point algorithm into fixed-point code on MSP430 and
MSP432 devices. These routines are typically used in computationally intensive real-time applications where
optimal execution speed, high accuracy, and ultra-low energy are critical. By using the IQmath and Qmath
libraries, it is possible to achieve execution speeds considerably faster and energy consumption considerably
lower than equivalent code written using floating-point math.
Floating Point Math Library for MSP430
Continuing to innovate in the low power and low cost microcontroller space, TI brings you MSPMATHLIB.
Leveraging the intelligent peripherals of our devices, this floating point math library of scalar functions brings you
up to 26x better performance. Mathlib is easy to integrate into your designs. This library is free and is integrated
in both Code Composer Studio and IAR IDEs. Read the user's guide for an in depth look at the math library and
relevant benchmarks.
Development Tools
Code Composer Studio™ Integrated Development Environment for MSP Microcontrollers
Code Composer Studio is an integrated development environment (IDE) that supports all MSP microcontroller
devices. Code Composer Studio comprises a suite of embedded software utilities used to develop and debug
embedded applications. It includes an optimizing C/C++ compiler, source code editor, project build environment,
debugger, profiler, and many other features.
Command-Line Programmer
MSP Flasher is an open-source shell-based interface for programming MSP microcontrollers through a FET
programmer or eZ430 using JTAG or Spy-Bi-Wire (SBW) communication. MSP Flasher can download binary
files (.txt or .hex) files directly to the MSP microcontroller without an IDE.
MSP MCU Programmer and Debugger
The MSP-FET is a powerful emulation development tool – often called a debug probe – which allows users to
quickly begin application development on MSP low-power microcontrollers (MCU). Creating MCU software
usually requires downloading the resulting binary program to the MSP device for validation and debugging. The
MSP-FET provides a debug communication pathway between a host computer and the target MSP.
Furthermore, the MSP-FET also provides a Backchannel UART connection between the computer's USB
interface and the MSP UART. This affords the MSP programmer a convenient method for communicating serially
between the MSP and a terminal running on the computer.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
99
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
MSP-GANG Production Programmer
The MSP Gang Programmer is an MSP430 or MSP432 device programmer that can program up to eight
identical MSP430 or MSP432 Flash or FRAM devices at the same time. The MSP Gang Programmer connects
to a host PC using a standard RS-232 or USB connection and provides flexible programming options that allow
the user to fully customize the process. The MSP Gang Programmer is provided with an expansion board, called
the Gang Splitter, that implements the interconnections between the MSP Gang Programmer and multiple target
devices.
10.4 Documentation Support
The following documents describe the MSP430F525x devices. Copies of these documents are available on the
Internet at www.ti.com.
Receiving Notification of Document Updates
To receive notification of documentation updates—including silicon errata—go to the product folder for your
device on ti.com (for links to the product folders, see Section 10.5). In the upper right corner, click the "Alert me"
button. This registers you to receive a weekly digest of product information that has changed (if any). For change
details, see the revision history of any revised document.
Errata
MSP430F5259 Device Erratasheet
Describes the known exceptions to the functional specifications.
MSP430F5258 Device Erratasheet
Describes the known exceptions to the functional specifications.
MSP430F5257 Device Erratasheet
Describes the known exceptions to the functional specifications.
MSP430F5256 Device Erratasheet
Describes the known exceptions to the functional specifications.
MSP430F5255 Device Erratasheet
Describes the known exceptions to the functional specifications.
MSP430F5254 Device Erratasheet
Describes the known exceptions to the functional specifications.
MSP430F5253 Device Erratasheet
Describes the known exceptions to the functional specifications.
MSP430F5252 Device Erratasheet
Describes the known exceptions to the functional specifications.
100
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
User's Guides
MSP430F5xx and MSP430F6xx Family User's Guide
Detailed information on the modules and peripherals available in this device family.
MSP430 Flash Devices Bootloader (BSL) User's Guide
The MSP430 bootloader (BSL, formerly known as the bootstrap loader) allows users to communicate with
embedded memory in the MSP430 microcontroller during the prototyping phase, final production, and in service.
Both the programmable memory (flash memory) and the data memory (RAM) can be modified as required. Do
not confuse the bootloader with the bootstrap loader programs found in some digital signal processors (DSPs)
that automatically load program code (and data) from external memory to the internal memory of the DSP.
MSP430 Programming With the JTAG Interface
This document describes the functions that are required to erase, program, and verify the memory module of the
MSP430 flash-based and FRAM-based microcontroller families using the JTAG communication port. In addition,
it describes how to program the JTAG access security fuse that is available on all MSP430 devices. This
document describes device access using both the standard 4-wire JTAG interface and the 2-wire JTAG
interface, which is also referred to as Spy-Bi-Wire (SBW).
MSP430 Hardware Tools User's Guide
This manual describes the hardware of the TI MSP-FET430 Flash Emulation Tool (FET). The FET is the
program development tool for the MSP430 ultra-low-power microcontroller. Both available interface types, the
parallel port interface and the USB interface, are described.
Application Reports
MSP430 32-kHz Crystal Oscillators
Selection of the right crystal, correct load circuit, and proper board layout are important for a stable crystal
oscillator. This application report summarizes crystal oscillator function and explains the parameters to select the
correct crystal for MSP430 ultra-low-power operation. In addition, hints and examples for correct board layout
are given. The document also contains detailed information on the possible oscillator tests to ensure stable
oscillator operation in mass production.
MSP430 System-Level ESD Considerations
System-Level ESD has become increasingly demanding as silicon technology scales to lower voltages and the
need for designing cost-effective and ultra-low-power components. This application report addresses three ESD
topics to help board designers and OEMs understand and design robust system-level designs: (1) Componentlevel ESD testing and system-level ESD testing; (2) General design guidelines for system-level ESD protection;
(3) Introduction to System Efficient ESD Design (SEED), a co-design methodology of on-board and on-chip ESD
protection.
Designing With MSP430F522x and MSP430F521x Devices
The MSP430F522x and MSP430F521x devices support a split supply I/O system that is essential in systems in
which the MCU is required to interface with external devices (such as sensors or other processors) that operate
at different voltage level compared to the MCU device supply. Additionally, the split supply input voltage range of
the F522x and F521x devices starts as low as 1.62 V (see the device data sheet specifications), and this allows
for nominal 1.8-V I/O interface without the need for external level translation. This application report describes
the various design considerations to keep in mind while designing the F522x and F521x devices in an
application.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
101
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
10.5 Related Links
Table 10-2 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 10-2. Related Links
PARTS
PRODUCT FOLDER
ORDER NOW
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
MSP430F5259
Click here
Click here
Click here
Click here
Click here
MSP430F5258
Click here
Click here
Click here
Click here
Click here
MSP430F5257
Click here
Click here
Click here
Click here
Click here
MSP430F5256
Click here
Click here
Click here
Click here
Click here
MSP430F5255
Click here
Click here
Click here
Click here
Click here
MSP430F5254
Click here
Click here
Click here
Click here
Click here
MSP430F5253
Click here
Click here
Click here
Click here
Click here
MSP430F5252
Click here
Click here
Click here
Click here
Click here
10.6 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
10.7 Trademarks
MicroStar Junior™, MSP430™, MSP430Ware™, EnergyTrace™, ULP Advisor™, Code Composer Studio™, and TI
E2E™ are trademarks of Texas Instruments.
Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
All other trademarks are the property of their respective owners.
10.8 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
10.9 Export Control Notice
Recipient agrees to not knowingly export or re-export, directly or indirectly, any product or technical data (as
defined by the U.S., EU, and other Export Administration Regulations) including software, or any controlled
product restricted by other applicable national regulations, received from disclosing party under nondisclosure
obligations (if any), or any direct product of such technology, to any destination to which such export or re-export
is restricted or prohibited by U.S. or other applicable laws, without obtaining prior authorization from U.S.
Department of Commerce and other competent Government authorities to the extent required by those laws.
10.10 Glossary
TI Glossary
102
This glossary lists and explains terms, acronyms, and definitions.
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
MSP430F5259, MSP430F5258, MSP430F5257, MSP430F5256
MSP430F5255, MSP430F5254, MSP430F5253, MSP430F5252
www.ti.com
SLAS903D – MAY 2013 – REVISED OCTOBER 2020
11 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: MSP430F5259 MSP430F5258 MSP430F5257 MSP430F5256 MSP430F5255
MSP430F5254 MSP430F5253 MSP430F5252
103
PACKAGE OPTION ADDENDUM
www.ti.com
14-Feb-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
MSP430F5252IRGCR
ACTIVE
VQFN
RGC
64
2000
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5252
MSP430F5252IRGCT
ACTIVE
VQFN
RGC
64
250
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5252
MSP430F5253IRGCR
ACTIVE
VQFN
RGC
64
2000
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5253
MSP430F5253IRGCT
ACTIVE
VQFN
RGC
64
250
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5253
MSP430F5254IRGCR
ACTIVE
VQFN
RGC
64
2000
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5254
MSP430F5254IRGCT
ACTIVE
VQFN
RGC
64
250
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5254
MSP430F5255IRGCR
ACTIVE
VQFN
RGC
64
2000
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5255
MSP430F5255IRGCT
ACTIVE
VQFN
RGC
64
250
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5255
MSP430F5256IRGCR
ACTIVE
VQFN
RGC
64
2000
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5256
MSP430F5256IRGCT
ACTIVE
VQFN
RGC
64
250
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5256
MSP430F5257IRGCR
ACTIVE
VQFN
RGC
64
2000
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5257
MSP430F5257IRGCT
ACTIVE
VQFN
RGC
64
250
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5257
MSP430F5258IRGCR
ACTIVE
VQFN
RGC
64
2000
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5258
MSP430F5258IRGCT
ACTIVE
VQFN
RGC
64
250
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5258
MSP430F5259IRGCR
ACTIVE
VQFN
RGC
64
2000
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5259
MSP430F5259IRGCT
ACTIVE
VQFN
RGC
64
250
RoHS & Green
NIPDAU
Level-3-260C-168 HR
-40 to 85
F5259
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
14-Feb-2021
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of