Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
NE5534x, SA5534x Low-Noise Operational Amplifiers
1 Features
3 Description
•
The NE5534, NE5534A, SA5534, and SA5534A
devices are high-performance operational amplifiers
combining excellent dc and ac characteristics. Some
of the features include very low noise, high outputdrive capability, high unity-gain and maximum-outputswing bandwidths, low distortion, and high slew rate.
1
•
•
•
•
•
•
•
•
•
Equivalent Input Noise Voltage
3.5 nV/√Hz Typ
Unity-Gain Bandwidth 10 MHz Typ
Common-Mode Rejection Ratio 100 dB Typ
High DC Voltage Gain 100 V/mV Typ
Peak-to-Peak Output Voltage Swing 32 V Typ
With VCC± = ±18 V and RL = 600 Ω
High Slew Rate 13 V/μs Typ
Wide Supply-Voltage Range ±3 V to ±20 V
Low Harmonic Distortion
Offset Nulling Capability
External Compensation Capability
These operational amplifiers are compensated
internally for a gain equal to or greater than three.
Optimization of the frequency response for various
applications can be obtained by use of an external
compensation capacitor between COMP and
COMP/BAL. The devices feature input-protection
diodes, output short-circuit protection, and offsetvoltage nulling capability with use of the BALANCE
and COMP/BAL pins (see Figure 10).
For the NE5534A and SA5534A devices, a maximum
limit is specified for the equivalent input noise
voltage.
2 Applications
•
•
•
•
Audio Preamplifiers
Servo Error Amplifiers
Medical Equipment
Telephone Channel Amplifiers
Device Information
PART NUMBER
NE5534x
SA5534x
PACKAGE (PIN)
BODY SIZE (NOM)
SOIC (8)
4.90 mm × 3.91 mm
SOIC (8)
4.90 mm × 3.91 mm
SO (8)
6.20 mm × 5.30 mm
4 Simplified Schematic
COMP
COMP/BAL
IN−
−
OUT
IN+
+
BALANCE
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
4
7.1
7.2
7.3
7.4
7.5
7.6
7.7
4
4
4
4
5
6
7
Absolute Maximum Ratings ......................................
Handling Ratings.......................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Operating Characteristics..........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
8.1 Overview ................................................................... 9
8.2 Functional Block Diagram ......................................... 9
8.3 Feature Description................................................. 10
8.4 Device Functional Modes........................................ 10
9
Application and Implementation ........................ 11
9.1 General Application................................................. 11
9.2 Typical Application ................................................. 12
10 Power Supply Recommendations ..................... 14
11 Layout................................................................... 15
11.1 Layout Guidelines ................................................. 15
11.2 Layout Example .................................................... 15
12 Device and Documentation Support ................. 16
12.1
12.2
12.3
12.4
Related Links ........................................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
16
16
16
16
13 Mechanical, Packaging, and Orderable
Information ........................................................... 16
5 Revision History
Changes from Revision C (September 2004) to Revision D
Page
•
Added Applications,Device Information table, Handling Ratings table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ..... 1
•
Deleted Ordering Information table. ....................................................................................................................................... 1
2
Submit Documentation Feedback
Copyright © 1979–2014, Texas Instruments Incorporated
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
NE5534, NE5534A, SA5534, SA5534A
www.ti.com
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
6 Pin Configuration and Functions
NE5534, SA5534 . . . D (SOIC), P (PDIP),
OR PS (SOP) PACKAGE
NE5534A, SA5534A . . . D (SOIC) OR P (PDIP) PACKAGE
(TOP VIEW)
BALANCE
IN−
IN+
VCC−
1
8
2
7
3
6
4
5
COMP/BAL
VCC+
OUT
COMP
Pin Functions
PIN
NAME
NO.
BALANCE
1
COMP/BAL
COMP
TYPE
DESCRIPTION
I
External frequency compensation
8
I
External offset voltage adjustment/External frequency compensation
5
O
External offset voltage adjustment
IN+
3
I
Noninverting input
IN-
2
I
Inverting Input
OUT
6
O
Output
VCC+
7
—
Positive Supply
VCC-
4
—
Negative Supply
Copyright © 1979–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
3
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
VCC+
Supply voltage (2)
VCC
TYP
0
VCC–
(1)
(2)
(3)
(4)
(5)
UNIT
22
V
V
–22
0
Input voltage, either input (2) (3)
VCC–
VCC+
V
Input current (4)
–10
10
mA
150
°C
Duration of output short circuit (5)
TJ
MAX
Unlimited
Operating virtual-junction temperature
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC–.
The magnitude of the input voltage must never exceed the magnitude of the supply voltage.
Excessive current will flow if a differential input voltage in excess of approximately 0.6 V is applied between the inputs, unless some
limiting resistance is used.
The output may be shorted to ground or either power supply. Temperature and/or supply voltages must be limited to ensure the
maximum dissipation rating is not exceeded.
7.2 Handling Ratings
Tstg
MIN
MAX
UNIT
–65
150
°C
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001,
all pins
0
2000
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins
0
200
Storage temperature range
V(ESD)
Electrostatic discharge
V
7.3 Recommended Operating Conditions
MIN
VCC
Supply voltage
TA
Operating free-air temperature
MAX
UNIT
VCC+
5
15
V
VCC–
–5
–15
V
NE5534, NE5534A
0
70
SA5534, SA5534A
–40
85
°C
7.4 Thermal Information
THERMAL METRIC
NE5534, NE5534A
SA5534, and SA5534A
(1)
D
P
PS
UNIT
8 PINS
RθJA
(1)
(2)
(3)
4
Package thermal impedance
(2) (3)
97
85
95
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report (SPRA953).
The package thermal impedance is calculated in accordance with JESD 51-7.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA) / θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
Submit Documentation Feedback
Copyright © 1979–2014, Texas Instruments Incorporated
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
NE5534, NE5534A, SA5534, SA5534A
www.ti.com
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
7.5 Electrical Characteristics
VCC± = ±15 V, TA = 25°C (unless otherwise noted)
TEST CONDITIONS (1)
PARAMETER
VIO
Input offset voltage
VO = 0
RS = 50 Ω
IIO
Input offset current
VO = 0
IIB
Input bias current
VO = 0
VICR
Common-mode input-voltage range
VO(PP)
Maximum peak-to-peak output-voltage swing
RL ≥ 600 Ω
VO = ±10 V
RL ≥ 600 Ω,
AVD
Large-signal differential-voltage amplification
RL ≥ 2 kΩ, VO±10 V
Avd
Small-signal differential-voltage amplification
f = 10 kHz
VO = ±10 V
BOM
Unity-gain bandwidth
ri
Input resistance
zo
Output impedance
kSVR
Supply-voltage rejection ratio (ΔVCC or ΔVIO)
IOS
Output short-circuit current
ICC
Total supply current
MAX
0.5
4
TA = Full range
5
TA = 25°C
20
TA = Full range
300
400
TA = 25°C
500
TA = Full range
1500
2000
±12
±13
VCC± = ±15 V
24
26
VCC± = ±18 V
30
32
TA = 25°C
25
100
TA = Full range
15
TA = 25°C
25
TA = Full range
15
CC = 0
2.2
CC = 0
200
95
VCC± 18 V,
RL = 600 Ω
VO = ±14 V
CC = 22 pF
70
CC = 22 pF
CL = 100 pF
mV
nA
nA
V
V/mV
100
CC = 22 pF
UNIT
V
6
30
CMRR Common-mode rejection ratio
(1)
TA = 25°C
TYP
CC = 22 pF
Maximum output-swing bandwidth
B1
MIN
V/mV
kHz
10
MHz
100
kΩ
0.3
Ω
AVD = 30 dB,
CC = 22 pF
RL = 600 Ω,
f = 10 kHz
VO = 0,
RS = 50 Ω
VIC = VICRmin
70
100
dB
VCC± = ±9 V to ±15 V,
VO = 0
RS = 50 Ω
80
100
dB
38
mA
VO = 0, No load
TA = 25°C
4
8
mA
All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. For
NE5534 and NE5534A, full range is 0°C to 70°C. For SA5534 and SA5534A, full range is –40°C to 85°C.
Copyright © 1979–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
5
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
www.ti.com
7.6 Operating Characteristics
VCC± = ±15 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
NE5534,
SA5534
TYP
SR
Slew rate
Rise time
Overshoot factor
tr
Rise time
Overshoot factor
Vn
Equivalent input noise voltage
In
Equivalent input noise current
F
Average noise figure
6
NE5534A, SA5534A
MIN
TYP
UNIT
MAX
CC = 0
13
13
CC = 22 pF
6
6
20
20
20
20
%
50
50
ns
35%
—
VI = 50 mV,
RL = 600 Ω,
CL = 100 pF
VI = 50 mV,
RL = 600 Ω,
CL = 500 pF
AVD = 1,
CC = 22 pF
AVD = 1,
CC = 47 pF
35%
V/μs
ns
f = 30 Hz
7
5.5
7
f = 1 kHz
4
3.5
4.5
f = 30 Hz
2.5
1.5
f = 1 kHz
0.6
0.4
RS = 5 kΩ
Submit Documentation Feedback
f = 10Hz to 20 kHz
0.9
nV/√Hz
pA/√Hz
dB
Copyright © 1979–2014, Texas Instruments Incorporated
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
NE5534, NE5534A, SA5534, SA5534A
www.ti.com
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
VO(PP)
VOPP − Maximum Peak-to-Peak Output Voltage − V
Normalized Input Bias Current and Input Offset Current
7.7 Typical Characteristics
1.6
VCC± = ±15 V
1.4
Offset
1.2
Bias
1
0.8
0.6
0.4
−75 −50
75 100
−25
0
25
50
TA − Free-Air Temperature − °C
125
20
15
10
CC = 22 pF
5
CC = 47 pF
VCC± = ±15 V
TA = 25°C
0
100
1k
10 k
100 k
1M
Figure 2. Maximum Peak-to-Peak Output Voltage
vs Frequency
105
104
103
CC = 0 pF
102
CC = 22 pF
10
100
1k
10 k 100 k 1 M
f − Frequency − Hz
10 M 100 M
Normalized Slew Rate and Unity-Gain Bandwidth
AVD − Differential Voltage Amplification − V/mV
25
1.2
VCC± = ±15 V
TA = 25°C
1
10
CC = 0
f − Frequency − Hz
Figure 1. Normalized Input Bias Current and Input Offset
Current
vs Free-Air Temperature
106
30
TA = 25°C
1.1
Unity-Gain
Bandwidth
1
0.9
0.8
0.7
Slew Rate
0.6
0.5
0.4
0
5
10
15
| VCC± | − Supply Voltage − V
20
Figure 3. Large-Signal Differential Voltage Amplification
vs Frequency
Figure 4. Normalized Slew Rate and Unity-Gain Bandwidth
vs Supply Voltage
Figure 5. Normalized Slew Rate and Unity-Gain Bandwidth
vs Free-Air Temperature
Figure 6. Total Harmonic Distortion
vs Frequency
Copyright © 1979–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
7
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
www.ti.com
Typical Characteristics (continued)
Figure 7. Equivalent Input Noise Voltage
vs Frequency
Figure 8. Equivalent Input Noise Current
vs Frequency
Figure 9. Total Equivalent Input Noise Voltage
vs Source Resistance
8
Submit Documentation Feedback
Copyright © 1979–2014, Texas Instruments Incorporated
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
NE5534, NE5534A, SA5534, SA5534A
www.ti.com
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
8 Detailed Description
8.1 Overview
The NE5534, NE5534A, SA5534, and SA5534A devices are high-performance operational amplifiers combining
excellent dc and ac characteristics. Some of the features include very low noise, high output-drive capability, high
unity-gain and maximum-output-swing bandwidths, low distortion, and high slew rate.
These operational amplifiers are compensated internally for a gain equal to or greater than three. Optimization of
the frequency response for various applications can be obtained by use of an external compensation capacitor
between COMP and COMP/BAL. The devices feature input-protection diodes, output short-circuit protection, and
offset-voltage nulling capability with use of the BALANCE and COMP/BAL pins (see the Application Circuit
Diagram).
For the NE5534A and SA5534A devices, a maximum limit is specified for the equivalent input noise voltage.
8.2 Functional Block Diagram
BALANCE
COMP/BAL
8
1
100 pF
IN+
12 kΩ
COMP
5
7
12 kΩ
3
40 pF
15 Ω
6
IN−
VCC+
2
12 pF
7 pF
15 Ω
4
Copyright © 1979–2014, Texas Instruments Incorporated
OUT
Submit Documentation Feedback
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
VCC−
9
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
www.ti.com
8.3 Feature Description
8.3.1 Offset-Voltage Null Capability
The input offset voltage of operational amplifiers (op amps) arises from unavoidable mismatches in the
differential input stage of the op-amp circuit caused by mismatched transistor pairs, collector currents, currentgain betas (β), collector or emitter resistors, and so on. The input offset pins allow the designer to adjust for
these mismatches by external circuitry. See the Application and Implementation section for more details on
design techniques.
8.3.2 Slew Rate
The slew rate is the rate at which an operational amplifier can change its output when there is a change on the
input. The NE5534 and SA5534 devices have a 13-V/μs slew rate.
8.3.3 Common-Mode Rejection Ratio
The common-mode rejection ratio (CMRR) of an amplifier is a measure of how well the device rejects unwanted
input signals common to both input leads. It is found by taking the ratio of the change in input offset voltage to
the change in the input voltage and converting to decibels. Ideally the CMRR is infinite, but in practice, amplifiers
are designed to have it as high as possible. The CMRR of the NE5534 and SA5534 devices is 100 dB.
8.3.4 Unity-Gain Bandwidth
The unity-gain bandwidth is the frequency up to which an amplifier with a unity gain may be operated without
greatly distorting the signal. The NE5534 and SA5534 devices have a 10-MHz unity-gain bandwidth.
8.3.5 External Compensation Capability
Frequency compensation with a capacitor may be used to increase the gain-bandwidth product (GBW) of the
amplifier. See the Application and Implementation section for more details on design techniques.
8.4 Device Functional Modes
The NE5534 and SA5534 devices are powered on when the supply is connected. Each of these devices can be
operated as a single supply operational amplifier or dual supply amplifier depending on the application.
10
Submit Documentation Feedback
Copyright © 1979–2014, Texas Instruments Incorporated
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
NE5534, NE5534A, SA5534, SA5534A
www.ti.com
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 General Application
The input offset voltage of operational amplifiers (op amps) arises from unavoidable mismatches in the
differential input stage of the op-amp circuit caused by mismatched transistor pairs, collector currents, currentgain betas (β), collector or emitter resistors, and so on. The input offset pins allow the designer to adjust for
these mismatches by external circuitry. These input mismatches can be adjusted by putting resistors or a
potentiometer between the inputs as shown in Figure 10. A potentiometer can be used to fine tune the circuit
during testing or for applications which require precision offset control. More information about designing using
the input-offset pins, see Offset Voltage of Operational Amplifiers (SLOA045).
VCC+
22 kΩ
100 kΩ
CC
−
5534
+
VCC−
Frequency Compensation and Offset-Voltage Nulling Circuit
Figure 10. Application Circuit
Copyright © 1979–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
11
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
www.ti.com
9.2 Typical Application
The voltage follower configuration of the operational amplifier is used for applications where a weak signal is
used to drive a relatively high current load. This circuit is also called a buffer amplifier or unity gain amplifier. The
inputs of an operational amplifier have a very high resistance which puts a negligible current load on the voltage
source. The output resistance of the operational amplifier is almost negligible, so it can provide as much current
as necessary to the output load.
10 k
12 V
VOUT
+
VIN
Figure 11. Voltage Follower Schematic
9.2.1 Design Requirements
• Output range of 2 V to 11 V
• Input range of 2 V to 11 V
9.2.2 Detailed Design Procedure
9.2.2.1 Output Voltage Swing
The output voltage of an operational amplifier is limited by its internal circuitry to some level below the supply
rails. For this amplifier, the output voltage swing is within ±12 V, which accommodates the input and output
voltage requirements.
9.2.2.2 Supply and Input Voltage
For correct operation of the amplifier, neither input must be higher than the recommended positive supply rail
voltage or lower than the recommended negative supply rail voltage. The chosen amplifier must be able to
operate at the supply voltage that accommodates the inputs. Because the input for this application goes up to
11 V, the supply voltage must be 12 V. Using a negative voltage on the lower rail rather than ground, allows the
amplifier to maintain linearity for inputs below 2 V.
12
Submit Documentation Feedback
Copyright © 1979–2014, Texas Instruments Incorporated
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
NE5534, NE5534A, SA5534, SA5534A
www.ti.com
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
Typical Application (continued)
9.2.3 Application Curves for Output Characteristics
12
4
2
10
0
IIN (mA)
VOUT (V)
8
6
±2
±4
±6
4
±8
2
±10
0
±12
0
2
4
6
8
10
VIN (V)
12
0
2
4
6
8
10
VIN (V)
C001
Figure 12. Output Voltage vs Input Voltage
12
C002
Figure 13. Current Drawn by the Input of the Voltage
Follower (IIN) vs the Input Voltage
20
18
16
ICC (mA)
14
12
10
8
6
4
2
0
0
2
4
6
VIN (V)
8
10
12
C003
Figure 14. Current Drawn from Supply (ICC) vs the Input Voltage
Copyright © 1979–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
13
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
www.ti.com
10 Power Supply Recommendations
The NE5534 and SA5534 devices are specified for operation from ±5 to ±15 V; many specifications apply from
0°C to 70°C for the NE5534 device and –40°C to 85°C for the SA5534 device.
CAUTION
Supply voltages larger than ±22 V can permanently damage the device (see the
Absolute Maximum Ratings).
Place 0.1-μF bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or high
impedance power supplies. For more detailed information on bypass capacitor placement, refer to the Layout
Guidelines.
14
Submit Documentation Feedback
Copyright © 1979–2014, Texas Instruments Incorporated
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
NE5534, NE5534A, SA5534, SA5534A
www.ti.com
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
11 Layout
11.1 Layout Guidelines
•
•
•
•
•
•
For best operational performance of the device, use good PCB layout practices, including:
Noise can propagate into analog circuitry through the power pins of the circuit as a whole, as well as the
operational amplifier. Bypass capacitors are used to reduce the coupled noise by providing low-impedance
power sources local to the analog circuitry.
– Connect low-ESR, 0.1-μF ceramic bypass capacitors between each supply pin and ground, placed as
close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single
supply applications.
Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective
methods of noise suppression. On multilayer PCBs, one or more layers are usually devoted to ground planes.
A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital
and analog grounds, paying attention to the flow of the ground current. For more detailed information, refer to
Circuit Board Layout Techniques (SLOA089).
To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If
it is not possible to keep them separate, it is much better to cross the sensitive trace perpendicularly, as
opposed to in parallel, with the noisy trace.
Place the external components as close to the device as possible. Keeping RF and RG close to the inverting
input minimizes parasitic capacitance, as shown in .
Keep the length of input traces as short as possible. Always remember that the input traces are the most
sensitive part of the circuit.
Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce
leakage currents from nearby traces that are at different potentials.
11.2 Layout Example
RIN
VIN
RG
+
VOUT
RF
Figure 15. Operational Amplifier Schematic for Noninverting Configuration
Place components close to
device and to each other to
reduce parasitic errors
Run the input traces as far
away from the supply lines
as possible
RF
BALANCE
COMP/BAL
IN1í
VCC+
IN1+
OUT
VCCí
COMP
VS+
Use low-ESR, ceramic
bypass capacitor
RG
GND
VIN
RIN
GND
Only needed for
dual-supply
operation
GND
VS(or GND for single supply)
VOUT
Ground (GND) plane on another layer
Figure 16. Operational Amplifier Board Layout for Noninverting Configuration
Copyright © 1979–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
15
NE5534, NE5534A, SA5534, SA5534A
SLOS070D – JULY 1979 – REVISED NOVEMBER 2014
www.ti.com
12 Device and Documentation Support
12.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
NE5534
Click here
Click here
Click here
Click here
Click here
NE5534A
Click here
Click here
Click here
Click here
Click here
SA5534
Click here
Click here
Click here
Click here
Click here
SA5534A
Click here
Click here
Click here
Click here
Click here
12.2 Trademarks
All trademarks are the property of their respective owners.
12.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
16
Submit Documentation Feedback
Copyright © 1979–2014, Texas Instruments Incorporated
Product Folder Links: NE5534 NE5534A SA5534 SA5534A
PACKAGE OPTION ADDENDUM
www.ti.com
14-Aug-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
NE5534AD
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
5534A
NE5534ADR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
5534A
NE5534ADRE4
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
5534A
NE5534ADRG4
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
5534A
NE5534AP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
NE5534AP
NE5534APE4
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
NE5534AP
NE5534D
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
NE5534
NE5534DR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
NE5534
NE5534DRE4
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
NE5534
NE5534DRG4
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
NE5534
NE5534P
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
NE5534P
NE5534PE4
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
NE5534P
SA5534AD
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
SA5534A
SA5534ADR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
SA5534A
SA5534AP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 85
SA5534AP
SA5534APE4
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 85
SA5534AP
SA5534D
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
SA5534
SA5534DR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
SA5534
SA5534P
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 85
SA5534P
SA5534PSR
ACTIVE
SO
PS
8
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
SA5534
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
14-Aug-2021
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of