OPA140ATDD1

OPA140A-DIE www.ti.com SBOS610B – MARCH 2012 – REVISED MARCH 2012 HIGH-PRECISION, LOW-NOISE, RAIL-TO-RAIL OUTPUT, 11-MHZ JFET OPERATIONAL AMPLIFIER Check for Samples: OPA140A-DIE FEATURES 1 • • • • • • • • • • • Very Low Offset Drift Very Low Offset Low Input Bias Current Very Low 1/f Noise Low Noise Slew Rate Low Supply Current Input Voltage Range Includes V– Supply Single-Supply Operation: 4.5 V to 36 V Dual-Supply Operation: ±2.25 V to ±18 V No Phase Reversal APPLICATIONS • • • • • • • Battery-Powered Instruments Industrial Controls Medical Instrumentation Photodiode Amplifiers Active Filters Data Acquisition Systems Automatic Test Systems DESCRIPTION The OPA140A operational amplifier is a low-power JFET input amplifier that features good drift and low input bias current. The rail-to-rail output swing and input range that includes V– allow designers to take advantage of the low-noise characteristics of JFET amplifiers while also interfacing to modern, single-supply, precision analogto-digital converters (ADCs) and digital-to-analog converters (DACs). The OPA140A runs on a single 4.5-V to 36-V supply or dual ±2.25-V to ±18-V supplies. ORDERING INFORMATION (1) (1) (2) PRODUCT PACKAGE DESIGNATOR PACKAGE (2) OPA140A TD Bare Die In Waffle Pack ORDERABLE PART NUMBER PACKAGE QUANTITY OPA140ATDD1 252 OPA140ATDD2 10 For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Processing is per the Texas Instruments commercial production baseline and is in compliance with the Texas Instruments Quality Control System in effect at the time of manufacture. Electrical screening consists of DC parametric and functional testing at room temperature only. Unless otherwise specified by Texas Instruments AC performance and performance over temperature is not warranted. Visual Inspection is performed in accordance with MIL-STD-883 Test Method 2010 Condition B at 75X minimum. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2012, Texas Instruments Incorporated OPA140A-DIE www.ti.com SBOS610B – MARCH 2012 – REVISED MARCH 2012 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. BARE DIE INFORMATION DIE THICKNESS BACKSIDE FINISH BACKSIDE POTENTIAL BOND PAD METALLIZATION COMPOSITION BOND PAD THICKNESS 15 mils. Silicon with backgrind Floating TiW/AlCu (0.5%) 1100 nm Table 1. Bond Pad Coordinates in Microns DESCRIPTION PAD NUMBER VIN 1 N/C 2 X MIN Y MIN 469.600 -720.500 544.600 X MAX -645.500 Y MAX 49.500 -430.500 124.500 -355.500 -49.550 VIP 3 N/C 4 V- 5 1034.050 -124.550 1109.050 OUT 6 1264.500 -107.500 1339.500 -32.500 V+ 7 1264.500 -737.500 1339.500 -662.500 2 Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): OPA140A-DIE PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) (3) Device Marking Samples (4/5) (6) OPA140ATDD1 ACTIVE 0 252 RoHS & Green Call TI N / A for Pkg Type Samples OPA140ATDD2 ACTIVE 0 10 RoHS & Green Call TI N / A for Pkg Type Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of