OPA2277PG4

OPA 277 OPA 227 7 OPA 4277 OPA2 77 OPA2 277 OPA4 277 OPA2 77 OPA2 277 OPA277 OPA2277 OPA4277 SBOS079A – MARCH 1999 – REVISED APRIL 2005 High Precision OPERATIONAL AMPLIFIERS FEATURES q ULTRA LOW OFFSET VOLTAGE: 10µV q ULTRA LOW DRIFT: ±0.1µV/°C q HIGH OPEN-LOOP GAIN: 134dB q HIGH COMMON-MODE REJECTION: 140dB q HIGH POWER SUPPLY REJECTION: 130dB q LOW BIAS CURRENT: 1nA max q WIDE SUPPLY RANGE: ±2V to ±18V q LOW QUIESCENT CURRENT: 800µA/amplifier q SINGLE, DUAL, AND QUAD VERSIONS q REPLACES OP-07, OP-77, OP-177 DESCRIPTION The OPA277 series precision op amps replace the industry standard OP-177. They offer improved noise, wider output voltage swing, and are twice as fast with half the quiescent current. Features include ultra low offset voltage and drift, low bias current, high common-mode rejection, and high power supply rejection. Single, dual, and quad versions have identical specifications for maximum design flexibility. OPA277 series op amps operate from ±2V to ±18V supplies with excellent performance. Unlike most op amps which are specified at only one supply voltage, the OPA277 series is specified for real-world applications; a single limit applies over the ±5V to ±15V supply range. High performance is maintained as the amplifiers swing to their specified limits. Because the initial offset voltage (±20µV max) is so low, user adjustment is usually not required. However, the single version (OPA277) provides external trim pins for special applications. OPA277 op amps are easy to use and free from phase inversion and overload problems found in some other op amps. They are stable in unity gain and provide excellent dynamic behavior over a wide range of load conditions. Dual and quad versions feature completely independent circuitry for lowest crosstalk and freedom from interaction, even when overdriven or overloaded. Single (OPA277) and dual (OPA2277) versions are available in DIP-8, SO-8, and DFN-8 (4mm x 4mm) packages. The quad (OPA4277) comes in DIP-14 and SO-14 surface-mount packages. All are fully specified from –40°C to +85°C and operate from –55°C to +125°C. OPA277AIDRM APPLICATIONS q q q q q q q TRANSDUCER AMPLIFIER BRIDGE AMPLIFIER TEMPERATURE MEASUREMENTS STRAIN GAGE AMPLIFIER PRECISION INTEGRATOR BATTERY POWERED INSTRUMENTS TEST EQUIPMENT OPA277 Offset Trim –In +In V– 1 2 3 4 8-Pin DIP, SO-8 8 7 6 5 Offset Trim V+ Output NC OPA4277 1 2 A D 12 11 10 B C 9 8 14-Pin DIP, SO-14 V− 4 5 Offset Trim −In 1 Pin 1 Indicator 8 Offset Trim Out A –In A +In A V+ +In B 14 13 Out D –In D 2 7 V+ +In 3 6 Output 3 4 5 6 7 +In D V– +In C –In C Out C +In A 3 Out A −In A 1 OPA2277AIDRM V− 4 5 NC 8 Pin 1 Indicator Out B DFN-8 4mm x 4mm (top view) Thermal Pad on Bottom (Connect to V−) OPA2277 Out A –In A +In A V– 1 2 3 4 8-Pin DIP, SO-8 A B 8 7 6 5 V+ Out B –In B +In B –In B Out B 2 7 V+ −In B 6 +In B NC = No connection. DFN-8 4mm x 4mm (top view) Thermal Pad on Bottom (Connect to V−) Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1999-2005, Texas Instruments Incorporated www.ti.com ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage .................................................................................... 36V Input Voltage ..................................................... (V–) –0.7V to (V+) +0.7V Output Short-Circuit(2) .............................................................. Continuous Operating Temperature .................................................. –55°C to +125°C Storage Temperature ..................................................... –55°C to +125°C Junction Temperature ...................................................................... 150°C Lead Temperature (soldering, 10s) ................................................. 300°C ESD Rating (Human Body Model) .................................................. 2000V (Machine Model) ........................................................... 100V NOTE: (1) Stresses above these rating may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. (2) Short-circuit to ground, one amplifier per package. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION(1) OFFSET VOLTAGE max, µV ±50 ±20 ±50 ±20 ±100 ±50 ±25 ±50 ±25 ±100 ±50 ±50 OFFSET VOLTAGE DRIFT max, µV/°C ±1 ±0.15 ±1 ±0.15 ±1 ±1 ±0.25 ±1 ±0.25 ±1 ±1 ±1 PRODUCT Single OPA277PA OPA277P OPA277UA OPA277U OPA277AIDRM Dual OPA2277PA OPA2277P OPA2277UA OPA2277U OPA2277AIDRM Quad OPA4277PA OPA4277UA PACKAGE-LEAD DIP-8 DIP-8 SO-8 Surface Mount SO-8 Surface Mount DFN-8 (4mm x 4mm) DIP-8 DIP-8 SO-8 Surface Mount SO-8 Surface Mount DFN-8 (4mm x 4mm) DIP-14 SO-14 Surface Mount NOTE: (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet or visit the TI web site at www.ti.com. PIN DESCRIPTIONS OPA277 Offset Trim –In +In V– 1 2 3 4 8-Pin DIP, SO-8 8 7 6 5 Offset Trim V+ −In A 2 OPA2277AIDRM Out A 1 Pin 1 Indicator 8 Out B 7 V+ −In B Output NC(1) +In A 3 6 OPA4277 V− 4 5 +In B Out A –In A +In A V+ +In B –In B Out B OPA2277 1 2 A 3 4 5 B 6 7 14-Pin DIP, SO-14 C D 14 13 12 11 10 9 8 Out D –In D +In D V– OPA277AIDRM DFN-8 4mm x 4mm (top view) Thermal Pad on Bottom (Connect to V−) +In C –In C Out C −In 2 Offset Trim 1 Pin 1 Indicator 8 Offset Trim 7 V+ Out A –In A +In A V– 1 2 3 4 8-Pin DIP, SO-8 A B 8 7 6 5 V+ Out B –In B +In B +In V− 3 6 Output 4 5 NC DFN-8 4mm x 4mm (top view) NOTE: (1) NC = No connection. Thermal Pad on Bottom (Connect to V−) 2 OPA277, OPA2277, OPA4277 www.ti.com SBOS079A ELECTRICAL CHARACTERISTICS: VS = ±5V to VS = ±15V At TA = +25°C, and RL = 2kΩ, unless otherwise noted. Boldface limits apply over the specified temperature range, –40°C to +85°C. OPA277PA, UA OPA2277PA, UA OPA4277PA, UA MAX MIN TYP(1) MAX MIN OPA277P, U OPA2277P, U PARAMETER OFFSET VOLTAGE Input Offset Voltage: OPA277P, U (high grade, single) OPA2277P, U (high grade, dual) All PA, UA, Versions AIDRM Versions CONDITION MIN TYP(1) OPA277AIDRM, OPA2277AIDRM TYP(1) MAX UNITS VOS ±10 ±10 ±20 ±25 ±20 ±50 ±35 ±100 µV µV µV µV µV µV µV µV µV/°C µV/°C µV/°C µV/mo µV/V µV/V µV/V nA nA nA nA µVPP µVrms nV/√Hz nV/√Hz nV/√Hz nV/√Hz pA/√Hz Input Offset Voltage Over Temperature OPA277P, U (high grade, single) OPA2277P, U (high grade, dual) All PA, UA, Versions AIDRM Versions Input Offset Voltage Drift dVOS/dT OPA277P, U (high grade, single) OPA2277P, U (high grade, dual) All PA, UA, AIDRM Versions Input Offset Voltage: (all models) vs Time vs Power Supply TA = –40°C to +85°C Channel Separation (dual, quad) INPUT BIAS CURRENT Input Bias Current TA = –40°C to +85°C Input Offset Current TA = –40°C to +85°C NOISE Input Voltage Noise, f = 0.1 to 10Hz Input Voltage Noise Density, f = 10Hz en f = 100Hz f = 1kHz f = 10kHz Current Noise Density, f = 1kHz in INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection TA = –40°C to +85°C INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain AOL VCM CMRR TA = TA = TA = TA = –40°C –40°C –40°C –40°C to to to to +85°C +85°C +85°C +85°C ±30 ±50 ±100 ±165 TA = –40°C to +85°C TA = –40°C to +85°C TA = –40°C to +85°C ±0.1 ±0.1 ±0.15 ±0.25 ±0.15 ✻ ✻ ✻ ±1 ±0.15 ✻ ✻ ✻ ±1 PSRR VS = ±2V to ±18V VS = ±2V to ±18V dc 0.2 ±0.3 0.1 ±0.5 ±0.5 ±0.5 ±0.5 ±1 ±1 ±1 ±1 IB IOS ±1 ±2 ±1 ±2 ✻ ✻ ±2.8 ±4 ±2.8 ±4 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ 115 115 ±2.8 ±4 ±2.8 ±4 0.22 0.035 12 8 8 8 0.2 (V–) +2 130 128 (V+) –2 140 ✻ 115 115 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ VCM = (V–) +2V to (V+) –2V VCM = (V–) +2V to (V+) –2V ✻ V dB dB MΩ || pF GΩ || pF VCM = (V–) +2V to (V+) –2V VO = (V–)+0.5V to (V+)–1.2V, RL = 10kΩ VO = (V–)+1.5V to (V+)–1.5V, RL = 2kΩ 126 126 100 || 3 250 || 3 ✻ ✻ ✻ ✻ 140 134 ✻ ✻ 1 0.8 14 16 3 0.002 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ dB dB dB TA = –40°C to +85°C FREQUENCY RESPONSE Gain-Bandwidth Product GBW Slew Rate SR Settling Time, 0.1% 0.01% Overload Recovery Time Total Harmonic Distortion + Noise THD+N ✻ Specifications same as OPA277P, U. NOTE: (1) VS = ±15V. VO = (V–)+1.5V to (V+)–1.5V, RL = 2kΩ VS = ±15V, G = 1, 10V Step VS = ±15V, G = 1, 10V Step VIN • G = VS 1kHz, G = 1, VO = 3.5Vrms ✻ ✻ ✻ ✻ ✻ ✻ MHz V/µs µs µs µs % OPA277, OPA2277, OPA4277 SBOS079A www.ti.com 3 ELECTRICAL CHARACTERISTICS: VS = ±5V to VS = ±15V At TA = +25°C, and RL = 2kΩ, unless otherwise noted. Boldface limits apply over the specified temperature range, –40°C to +85°C. OPA277PA, UA OPA2277PA, UA OPA4277PA, UA MAX MIN TYP(1) MAX MIN OPA277P, U OPA2277P, U PARAMETER OUTPUT Voltage Output TA = –40°C to +85°C TA = –40°C to +85°C Short-Circuit Current Capacitive Load Drive POWER SUPPLY Specified Voltage Range Operating Voltage Range Quiescent Current (per amplifier) TA = –40°C to +85°C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SO-8 Surface-Mount DIP-8 DIP-14 SO-14 Surface-Mount DFN-8(2) CONDITION MIN TYP(1) (CONT) OPA277AIDRM, OPA2277AIDRM TYP(1) MAX UNITS VO RL = 10kΩ RL = 10kΩ R L = 2k Ω R L = 2k Ω (V–) (V–) (V–) (V–) +0.5 +0.5 +1.5 +1.5 (V+) (V+) (V+) (V+) –1.2 –1.2 –1.5 –1.5 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ISC CLOAD VS IQ IO = 0 IO = 0 –40 –55 –55 ±5 ±2 ±35 See Typical Curve ±15 ±18 ±825 ±900 +85 +125 +125 150 100 80 100 ✻ ✻ V V V V mA ±790 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ V V µA µA °C °C °C °C/W °C/W °C/W °C/W °C/W ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ θJA 45 ✻ Specifications same as OPA277P, U. NOTES: (1) VS = ±15V. (2) Thermal pad soldered to printed circuit board (PCB). 4 OPA277, OPA2277, OPA4277 www.ti.com SBOS079A TYPICAL CHARACTERISTICS At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted. OPEN-LOOP GAIN/PHASE vs FREQUENCY 140 120 100 AOL (dB) POWER SUPPLY AND COMMON-MODE REJECTION vs FREQUENCY 140 CL = 0 CL = 1500pF G 0 –30 Phase (°) 120 –PSR PSR, CMR (dB) +PSR 100 80 CMR 60 40 20 0 80 60 40 20 0 –20 0.1 1 φ –60 –90 –120 –150 –180 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 1k 10k 100k 1M Frequency (Hz) Frequency (Hz) INPUT NOISE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY 1000 INPUT NOISE VOLTAGE vs TIME Voltage Noise (nV/√Hz) Current Noise (fA/√Hz) Current Noise 100 Noise signal is bandwidth limited to lie between 0.1Hz and 10Hz. 50nV/div 10 Voltage Noise 1 1 10 100 Frequency (Hz) 1k 10k 1s/div CHANNEL SEPARATION vs FREQUENCY 140 1 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY VOUT = 3.5Vrms Channel Separation (dB) 120 THD+Noise (%) 0.1 G = 10, RL = 2kΩ, 10kΩ 0.01 G = 1, RL = 2kΩ, 10kΩ 0.001 10 100 1k 10k 100k 1M 10 100 1k Frequency (Hz) 10k 100k Frequency (Hz) 100 Dual and quad devices. G = 1, all channels. Quad measured channel A to D or B to C—other combinations yield similar or improved rejection. 80 60 40 OPA277, OPA2277, OPA4277 SBOS079A www.ti.com 5 TYPICAL CHARACTERISTICS (CONT) At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted. OFFSET VOLTAGE PRODUCTION DISTRIBUTION 16 14 Typical distribution of packaged units. Single, dual, and quad included. OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 35 30 Typical distribution of packaged units. Single, dual, and quad included. Percent of Amplifiers (%) 12 10 8 6 4 2 0 Percent of Amplifiers (%) 25 20 15 10 5 0 –50–45–40 –35–30–25–20–15–10 –5 0 5 10 15 20 25 30 35 40 45 50 Offset Voltage (µV) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Offset Voltage (µV/°C) WARM-UP OFFSET VOLTAGE DRIFT 3 Offset Voltage Change (µV) 2 1 0 –1 –2 –3 0 15 30 45 60 75 90 105 120 Time from Power Supply Turn-On (s) AOL, CMR, PSR (dB) AOL, CMR, PSR vs TEMPERATURE 160 150 CMR 140 130 PSR 120 110 100 –75 AOL –50 –25 0 25 50 75 100 125 Temperature (°C) INPUT BIAS CURRENT vs TEMPERATURE 5 4 Quiescent Current (µA) QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT vs TEMPERATURE 1000 950 900 850 800 750 700 650 600 550 –ISC +ISC ±IQ 100 90 Short-Circuit Current (mA) Input Bias Current (nA) 3 2 1 0 –1 –2 –3 –4 –5 –75 –50 –25 0 25 50 75 100 125 Temperature (°C) Curves represent typical production units. 80 70 60 50 40 30 20 10 0 –50 –25 0 25 50 75 100 125 Temperature (°C) 500 –75 6 OPA277, OPA2277, OPA4277 www.ti.com SBOS079A TYPICAL CHARACTERISTICS (CONT) At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted. CHANGE IN INPUT BIAS CURRENT vs POWER SUPPLY VOLTAGE 2.0 1.5 1.0 ∆IB (nA) CHANGE IN INPUT BIAS CURRENT vs COMMON-MODE VOLTAGE 2.0 Curve shows normalized change in bias current with respect to VCM = 0V. Typical IB may range from –05.nA to +0.5nA at VCM = 0V. VS = ±5V ∆IB (nA) Curve shows normalized change in bias current with respect to VS = ±10V (+20V). Typical IB may range from –0.5nA to +0.5nA at VS = ±10V. 1.5 1.0 0.5 0.0 –0.5 0.5 0.0 –0.5 –1.0 –1.5 –2.0 0 5 10 15 20 25 30 35 40 Supply Voltage (V) VCM = 0V VS = ±15V –1.0 –1.5 –2.0 –15 –10 –5 0 5 10 15 Common-Mode Voltage (V) QUIESCENT CURRENT vs SUPPLY VOLTAGE 1000 per amplifier Quiescent Current (µA) 900 Settling Time (µs) 50 100 SETTLING TIME vs CLOSED-LOOP GAIN 10V step CL = 1500pF 0.01% 0.1% 800 700 20 600 500 0 ±5 ±10 Supply Voltage (V) ±15 ±20 10 ±1 ±10 Gain (V/V) ±100 MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 30 25 Output Voltage (VPP) OUTPUT VOLTAGE SWING vs OUTPUT CURRENT (V+) (V+) – 1 Output Voltage Swing (V) VS = ±15V (V+) – 2 (V+) – 3 (V+) – 4 (V+) – 5 (V–) + 5 (V–) + 4 (V–) + 3 (V–) + 2 (V–) + 1 125°C 125°C 25°C 25°C –55°C 20 15 10 5 0 1k 10k Frequency (Hz) 100k 1M VS = ±5V –55°C (V–) 0 ±5 ±10 ±15 ±20 ±25 ±30 Output Current (mA) OPA277, OPA2277, OPA4277 SBOS079A www.ti.com 7 TYPICAL CHARACTERISTICS (CONT) At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted. SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE 60 Gain = –1 50 LARGE-SIGNAL STEP RESPONSE G = +1, CL = 1500pF, VS = +15V Overshoot (%) 40 30 20 Gain = ±10 10 0 10 100 1k Load Capacitance (pF) 10k 100k 10µs/div SMALL-SIGNAL STEP RESPONSE G = +1, CL = 0, VS = ±15V 2V/div Gain = +1 SMALL-SIGNAL STEP RESPONSE G = +1, CL = 1500pF, VS = ±15V 20mV/div 1µs/div 20mV/div 1µs/div 8 OPA277, OPA2277, OPA4277 www.ti.com SBOS079A APPLICATIONS INFORMATION The OPA277 series is unity-gain stable and free from unexpected output phase reversal, making it easy to use in a wide range of applications. Applications with noisy or high impedance power supplies may require decoupling capacitors close to the device pins. In most cases 0.1µF capacitors are adequate. The OPA277 series has very low offset voltage and drift. To achieve highest performance, circuit layout and mechanical conditions should be optimized. Offset voltage and drift can be degraded by small thermoelectric potentials at the op amp inputs. Connections of dissimilar metals will generate thermal potential which can degrade the ultimate performance of the OPA277 series. These thermal potentials can be made to cancel by assuring that they are equal in both input terminals. • Keep thermal mass of the connections made to the two input terminals similar. • Locate heat sources as far as possible from the critical input circuitry. • Shield op amp and input circuitry from air currents such as cooling fans. connecting a potentiometer as shown in Figure 1. This adjustment should be used only to null the offset of the op amp. This adjustment should not be used to compensate for offsets created elsewhere in a system since this can introduce additional temperature drift. V+ Trim Range: Exceeds Offset Voltage Specification 0.1µF 20kΩ 7 2 3 0.1µF 1 8 OPA277 4 6 OPA277 single op amp only. Use offset adjust pins only to null offset voltage of op amp—see text. V– FIGURE 1. OPA277 Offset Voltage Trim Circuit. INPUT PROTECTION The inputs of the OPA277 series are protected with 1kΩ series input resistors and diode clamps. The inputs can withstand ±30V differential inputs without damage. The protection diodes will, of course, conduct current when the inputs are over-driven. This may disturb the slewing behavior of unity-gain follower applications, but will not damage the op amp. OPERATING VOLTAGE OPA277 series op amp operate from ±2V to ±18V supplies with excellent performance. Unlike most op amps which are specified at only one supply voltage, the OPA277 series is specified for real-world applications; a single limit applies over the ±5V to ±15V supply range. This allows a customer operating at VS = ±10V to have the same assured performance as a customer using ±15V supplies. In addition, key parameters are assured over the specified temperature range, –40°C to +85°C. Most behavior remains unchanged through the full operating voltage range (±2V to ±18V). Parameters which vary significantly with operating voltage or temperature are shown in typical performance curves. INPUT BIAS CURRENT CANCELLATION The input stage base current of the OPA277 series is internally compensated with an equal and opposite cancellation circuit. The resulting input bias current is the difference between the input stage base current and the cancellation current. This residual input bias current can be positive or negative. When the bias current is canceled in this manner, the input bias current and input offset current are approximately the same magnitude. As a result, it is not necessary to use a bias current cancellation resistor as is often done with other op amps (Figure 2). A resistor added to cancel input bias current errors may actually increase offset voltage and noise. OFFSET VOLTAGE ADJUSTMENT The OPA277 series is laser-trimmed for very low offset voltage and drift so most circuits will not require external adjustment. However, offset voltage trim connections are provided on pins 1 and 8. Offset voltage can be adjusted by R2 R1 Op Amp R1 R2 OPA277 RB = R2 || R1 No bias current cancellation resistor (see text) (b) OPA277 with no external bias current cancellation resistor. (a) Conventional op amp with external bias current cancellation resistor. FIGURE 2. Input Bias Current Cancellation. OPA277, OPA2277, OPA4277 SBOS079A www.ti.com 9 V+ 1/2 OPA2277 R2 V– VOUT = (V1 – V2)(1 + R2 R1 ) R–∆R V1 R+∆R Load Cell R+∆R V2 R–∆R V+ R1 1/2 OPA2277 V– R2 R1 For integrated solution see: INA126, INA2126 (dual) INA125 (on-board reference) INA122 (single-supply) FIGURE 3. Load Cell Amplifier. IREG ∼ 1mA 5V 12 V+ Type J 1/2 OPA2277 RF 10kΩ R 412Ω 13 VLIN + VIN 1 IR1 14 IR2 11 VREG 10 V+ 4 RG 1250Ω 3 RG XTR105 RG – VIN RF 10kΩ B E IO 9 8 1kΩ 50Ω 25Ω RCM = 1250Ω 1/2 OPA2277 V– 2 7 6 + – IO = 4mA + (VIN – VIN) 40 RG IRET (G = 1 + 0.01µF 2RF = 50) R FIGURE 4. Thermocouple Low Offset, Low Drift Loop Measurement with Diode Cold Junction Compensation. 10 OPA277, OPA2277, OPA4277 www.ti.com SBOS079A DFN PACKAGE The OPA277 series uses the 8-lead DFN (also known as SON), which is a QFN package with contacts on only two sides of the package bottom. This leadless, near-chip-scale package maximizes board space and enhances thermal and electrical characteristics through an exposed pad. DFN packages are physically small, have a smaller routing area, improved thermal performance, and improved electrical parasitics, with a pinout scheme that is consistent with other commonly-used packages, such as SO and MSOP. Additionally, the absence of external leads eliminates bent-lead issues. The DFN package can be easily mounted using standard printed circuit board (PCB) assembly techniques. See Application Note, QFN/SON PCB Attachment (SLUA271) and Application Report, Quad Flatpack No-Lead Logic Packages (SCBA017), both available for download at www.ti.com. The exposed leadframe die pad on the bottom of the package should be connected to V–. LAYOUT GUIDELINES The leadframe die pad should be soldered to a thermal pad on the PCB. Mechanical drawings located at the end of this data sheet list the physical dimensions for the package and pad. Soldering the exposed pad significantly improves board-level reliability during temperature cycling, key push, package shear, and similar board-level tests. Even with applications that have low-power dissipation, the exposed pad must be soldered to the PCB to provide structural integrity and longterm reliability. OPA277, OPA2277, OPA4277 SBOS079A www.ti.com 11 PACKAGE OPTION ADDENDUM www.ti.com 28-Jun-2007 PACKAGING INFORMATION Orderable Device OPA2277AIDRMR OPA2277AIDRMRG4 OPA2277AIDRMT OPA2277AIDRMTG4 OPA2277P OPA2277PA OPA2277PAG4 OPA2277PG4 OPA2277U OPA2277U/2K5 OPA2277U/2K5G4 OPA2277UA OPA2277UA/2K5 OPA2277UA/2K5E4 OPA2277UAE4 OPA2277UAG4 OPA2277UG4 OPA277AIDRMR OPA277AIDRMRG4 OPA277AIDRMT OPA277AIDRMTG4 OPA277P OPA277PA OPA277PAG4 OPA277PG4 OPA277U Status (1) PREVIEW ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type SON SON SON SON PDIP PDIP PDIP PDIP SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SON SON SON SON PDIP PDIP PDIP PDIP SOIC Package Drawing DRM DRM DRM DRM P P P P D D D D D D D D D DRM DRM DRM DRM P P P P D Pins Package Eco Plan (2) Qty 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 3000 3000 250 250 50 50 50 50 100 TBD TBD Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Lead/Ball Finish Call TI Call TI CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU Call TI CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) Call TI Call TI Level-1-260C-UNLIM Level-1-260C-UNLIM N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Call TI Level-3-260C-168 HR Level-3-260C-168 HR Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Level-3-260C-168 HR 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 100 2500 2500 100 100 100 Green (RoHS & no Sb/Br) Pb-Free (RoHS) Pb-Free (RoHS) TBD Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 250 250 50 50 50 50 100 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 28-Jun-2007 Orderable Device OPA277U/2K5 OPA277U/2K5G4 OPA277UA OPA277UA/2K5 OPA277UA/2K5E4 OPA277UAE4 OPA277UAG4 OPA277UG4 OPA4277PA OPA4277PAG4 OPA4277UA OPA4277UA/2K5 OPA4277UA/2K5E4 OPA4277UAE4 OPA4277UAG4 (1) Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC PDIP PDIP SOIC SOIC SOIC SOIC SOIC Package Drawing D D D D D D D D N N D D D D D Pins Package Eco Plan (2) Qty 8 8 8 8 8 8 8 8 14 14 14 14 14 14 14 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 100 2500 2500 100 100 100 25 25 58 2500 2500 58 58 Green (RoHS & no Sb/Br) Pb-Free (RoHS) Pb-Free (RoHS) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Pb-Free (RoHS) Pb-Free (RoHS) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR N / A for Pkg Type N / A for Pkg Type Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR Level-3-260C-168 HR The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 28-Jun-2007 provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 2-Jul-2007 TAPE AND REEL INFORMATION Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 2-Jul-2007 Device Package Pins Site Reel Diameter (mm) 180 330 330 180 330 330 Reel Width (mm) 12 12 12 12 12 16 A0 (mm) B0 (mm) K0 (mm) P1 (mm) 8 8 8 8 8 8 W Pin1 (mm) Quadrant 12 12 12 12 12 16 Q2 Q1 Q2 Q2 Q1 Q1 OPA2277AIDRMT OPA2277UA/2K5 OPA277AIDRMR OPA277AIDRMT OPA277UA/2K5 OPA4277UA/2K5 DRM D DRM DRM D D 8 8 8 8 8 14 MLA MLA MLA MLA MLA MLA 4.3 6.9 4.3 4.3 6.9 6.5 4.3 5.4 4.3 4.3 5.4 9.5 1.5 2.0 1.5 1.5 2.0 2.1 TAPE AND REEL BOX INFORMATION Device OPA2277AIDRMT OPA2277UA/2K5 OPA277AIDRMR OPA277AIDRMT OPA277UA/2K5 OPA4277UA/2K5 Package DRM D DRM DRM D D Pins 8 8 8 8 8 14 Site MLA MLA MLA MLA MLA MLA Length (mm) 190.0 346.0 346.0 190.0 390.0 346.0 Width (mm) 212.7 346.0 346.0 212.7 348.0 346.0 Height (mm) 31.75 29.0 29.0 31.75 63.0 33.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 2-Jul-2007 Pack Materials-Page 3 MECHANICAL DATA MPDI001A – JANUARY 1995 – REVISED JUNE 1999 P (R-PDIP-T8) 0.400 (10,60) 0.355 (9,02) 8 5 PLASTIC DUAL-IN-LINE 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.015 (0,38) 0.200 (5,08) MAX Seating Plane 0.125 (3,18) MIN 0.010 (0,25) NOM Gage Plane 0.020 (0,51) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) M 0.430 (10,92) MAX 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers RFID Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated