OPA OPA
433
6
336
OPA2 336
OPA336 OPA2336 OPA4336
SBOS068B – JANUARY 1997 – REVISED APRIL 2004
SINGLE-SUPPLY, microPower CMOS OPERATIONAL AMPLIFIERS microAmplifier ™ Series
FEATURES
q q q q SINGLE-SUPPLY OPERATION RAIL-TO-RAIL OUTPUT (within 3mV) microPOWER: IQ = 20µA/Amplifier
microSIZE PACKAGES
DESCRIPTION
OPA336 series microPower CMOS operational amplifiers are designed for battery-powered applications. They operate on a single supply with operation as low as 2.1V. The output is rail-to-rail and swings to within 3mV of the supplies with a 100kΩ load. The common-mode range extends to the negative supply—ideal for single-supply applications. Single, dual, and quad versions have identical specifications for maximum design flexibility. In addition to small size and low quiescent current (20 µ A/amplifier), they feature low offset voltage (125µV max), low input bias current (1pA), and high openloop gain (115dB). Dual and quad designs feature completely independent circuitry for lowest crosstalk and freedom from interaction. OPA336 packages are the tiny SOT23-5 surface mount and SO-8 surface-mount. OPA2336 come in the miniature MSOP-8 surface-mount, SO-8 surface-mount, and DIP-8 packages. The OPA4336 package is the space-saving SSOP-16 surface-mount. All are specified from –40°C to +85°C and operate from –55°C to +125°C. A macromodel is available for download (at www.ti.com) for design analysis.
5 V+
q LOW OFFSET VOLTAGE: 125µV max q SPECIFIED FROM VS = 2.3V to 5.5V q SINGLE, DUAL, AND QUAD VERSIONS
APPLICATIONS
q q q q q q q BATTERY-POWERED INSTRUMENTS PORTABLE DEVICES HIGH-IMPEDANCE APPLICATIONS PHOTODIODE PRE-AMPS PRECISION INTEGRATORS MEDICAL INSTRUMENTS TEST EQUIPMENT
OPA336 Out V– +In 1 2
OPA4336 Out A 1 2 A D 14 13 12 B –In B Out B NC 6 7 8 SSOP-16 NC = No Connection C 11 10 9 –In C Out C NC +In D V– +In C 3 4 5 16 15 Out D –In D
3
4
–In
–In A
OPA336 NC –In +In V– 1 2 3 4 SO-8 NC = No Connection 8 7 6 5 NC V+ Output NC
SOT23-5
OPA2336 Out A –In A +In A V– 1 2 3 4 DIP-8, SO-8, MSOP-8 A B 8 7 6 5 V+ Out B –In B +In B
+In A V+ +In B
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright © 1997-2004, Texas Instruments Incorporated
www.ti.com
PACKAGE/ORDERING INFORMATION(1)
PACKAGE DRAWING DESIGNATOR DBV SPECIFIED TEMPERATURE RANGE –40°C to +85°C PACKAGE MARKING A36(2) ORDERING NUMBER(1) OPA336N/250 OPA336N/3K OPA336NA/250 OPA336NA/3K OPA336NJ/250 OPA336NJ/3K OPA336U OPA336U/2K5 OPA336UA OPA336UA/2K5 OPA336UJ OPA336UJ/2K5 OPA2336E/250 OPA2336E/2K5 OPA2336EA/250 OPA2336EA/2K5 OPA2336P OPA2336PA OPA2336U OPA2336U/2K5 OPA2336UA OPA2336UA/2K5 OPA4336EA/250 OPA4336EA/2K5 TRANSPORT MEDIA, QUANTITY Tape and Reel, 250 Tape and Reel, 3000 Tape and Reel, 250 Tape and Reel, 3000 Tape and Reel, 250 Tape and Reel, 3000 Rails(3), 100 Tape and Reel, 2500 Rails(3), 100 Tape and Reel, 2500 Rails(3), 100 Tape and Reel, 2500 Tape and Reel, 250 Tape and Reel, 2500 Tape and Reel, 250 Tape and Reel, 2500 Rails, 50 Rails, 50 Rails(3), 100 Tape and Reel, 2500 Rails(3), 100 Tape and Reel, 2500 Tape and Reel, 250 Tape and Reel, 2500
PRODUCT Single OPA336N
PACKAGE-LEAD SOT23-5
"
OPA336NA
"
SOT23-5
"
DBV
"
–40°C to +85°C
"
A36(2)
"
OPA336NJ
"
SOT23-5
"
DBV
"
–40°C to +85°C
"
J36
"
OPA336U
"
SO-8 Surface-Mount
"
D
"
–40°C to +85°C
"
OPA336U
"
OPA336UA
"
SO-8 Surface-Mount
"
D
"
–40°C to +85°C
"
OPA336UA
"
OPA336UJ(4)
"
SO-8 Surface-Mount
"
D
"
–40°C to +85°C
"
OPA336UJ
"
Dual OPA2336E " OPA2336EA " OPA2336P OPA2336PA OPA2336U " OPA2336UA " Quad OPA4336EA "
"
MSOP-8 Surface-Mount " MSOP-8 Surface-Mount " DIP-8 DIP-8 SO-8 Surface-Mount " SO-8 Surface-Mount " SSOP-16 Surface-Mount "
"
DGK " DGK " P P D " D " DBQ "
"
–40°C to +85°C " –40°C to +85°C " –40°C to +85°C –40°C to +85°C
"
B36(2) " B36(2) " OPA2336P OPA2336PA OPA2336U " OPA2336UA " OPA4336EA "
"
" –40°C to +85°C " –40°C to +85°C "
NOTES: (1) For the most current package and ordering information, see the package option addendum at the end of this data sheet. (2) Grade will be marked on the Reel. (3) SO-8 models also available in Tape and Reel. (4) Available Q2, 2004.
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage ................................................................................... 7.5V Signal Input Terminals, Voltage(2) ..................... (V–) –0.3V to (V+) +0.3V Current(2) .................................................... 10mA Output Short-Circuit(3) .............................................................. Continuous Operating Temperature .................................................. –55°C to +125°C Storage Temperature ..................................................... –55°C to +125°C Junction Temperature ...................................................................... 150°C Lead Temperature (soldering, 10s) ................................................. 300°C NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only. Functional operation of the device at these conditions, or beyond the specified operating conditions, is not implied. (2) Input terminals are diode-clamped to the power supply rails. Input signals that can swing more than 0.3V beyond the supply rails should be current-limited to 10mA or less. (3) Short-circuit to ground, one amplifier per package.
ELECTROSTATIC DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
2
OPA336, 2336, 4336
www.ti.com
SBOS068B
ELECTRICAL CHARACTERISTICS: VS = 2.3V to 5.5V
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C.
At TA = +25°C, VS = +5V, and RL = 25kΩ connected to VS/2, unless otherwise noted. OPA336NA, UA OPA2336EA, PA, UA OPA4336EA MIN TYP ✻ ✱ ✻ ✻ ±10 ±10 ✻ ✻ ✻ ✻ ✻ (V+) –1 90 ✻ 76 74 ✻ 86 ✻ 76 74 ✻ ✱ ✻ MAX ±500 ✻ ✱ ✻ ✱
OPA336N, U OPA2336E, P, U PARAMETER OFFSET VOLTAGE Input Offset Voltage vs Temperature vs Power Supply Over Temperature Channel Separation, dc INPUT BIAS CURRENT Input Bias Current Over Temperature Input Offset Current VOS dVOS/dT PSRR CONDITION MIN TYP(1) ±60 25 0.1 IB IOS ±1 ±1 3 40 30 –0.2 80 76 MAX ±125 100 130
OPA336NJ, UJ MIN TYP MAX UNITS ±500 ±2500 µV ✱ µV/°C ✻ ✻ µV/V ✱ µV/V ✻ µV/V ✻ ✻ ✻ ✻ ✻ ✻ 86 ✻ ✱ ✻ pA pA pA µVp-p nV/√Hz fA/√Hz V dB dB Ω || pF Ω || pF dB dB dB dB kHz V/µs µs mV mV mV mV mV mA pF V V µA µA °C °C °C °C/W °C/W °C/W °C/W °C/W °C/W
±1.5
VS = 2.3V to 5.5V VS = 2.3V to 5.5V
±60
NOISE Input Voltage Noise, f = 0.1 to 10Hz Input Voltage Noise Density, f = 1kHz en Current Noise Density, f = 1kHz in INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio Over Temperature INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain Over Temperature Over Temperature FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Overload Recovery Time OUTPUT Voltage Output Swing from Rail(2) Over Temperature Over Temperature Short-Circuit Current Capacitive Load Drive POWER SUPPLY Specified Voltage Range Minimum Operating Voltage Quiescent Current (per amplifier) Over Temperature TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SOT-23-5 Surface-Mount MSOP-8 Surface-Mount SO-8 Surface-Mount DIP-8 SSOP-16 Surface-Mount DIP-14 AOL RL = 25kΩ, 100mV < VO < (V+) – 100mV RL = 25kΩ, 100mV < VO < (V+) – 100mV RL = 5kΩ, 500mV < VO < (V+) – 500mV RL = 5kΩ, 500mV < VO < (V+) – 500mV GBW SR VS = 5V, G = 1 VS = 5V, G = 1 VIN • G = VS RL = 100kΩ, AOL ≥ 70dB RL = 25kΩ, AOL ≥ 90dB RL = 25kΩ, AOL ≥ 90dB RL = 5kΩ, AOL ≥ 90dB RL = 5kΩ, AOL ≥ 90dB ISC CLOAD VS IQ IO = 0 IO = 0 –40 –55 –55 θJA 2.3 100 100 90 90 VCM CMRR
–0.2V < VCM < (V+) –1V –0.2V < VCM < (V+) –1V
1013 || 2 1013 || 4 115 106 90 90 ✻ ✱
✻ ✻ ✻ ✻ 90 90 ✻ ✱
✻ ✻ ✻ ✻
100 0.03 100 3 20 70 ±5 See Text 5.5 2.1 20 32 36 +85 +125 +125 200 150 150 100 100 80 ✻ ✻ ✻ ✻
✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✱ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻
✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ 23 38 42 ✻ ✻ ✻ ✻ ✻
100 100 500 500
✻ ✱ ✻ ✱
✻ ✱ ✻ ✱
✻Specifications same as OPA2336E, P, U. NOTES: (1) VS = +5V. (2) Output voltage swings are measured between the output and positive and negative power-supply rails.
OPA336, 2336, 4336
SBOS068B
www.ti.com
3
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = +5V, and RL = 25kΩ connected to VS/2, unless otherwise noted.
OPEN-LOOP GAIN/PHASE vs FREQUENCY 100 80 G 0 –45
POWER-SUPPLY and COMMON-MODE REJECTION RATIO vs FREQUENCY 100 CMRR
80
PSRR, CMRR (dB)
Voltage Gain (dB)
60 40 20 0 –20 1 10 100 1k Frequency (Hz) 10k 100k 1M
Phase (°)
60 PSRR 40
Φ
–90 –135 –180
20
0 1 10 100 1k 10k 100k Frequency (Hz)
QUIESCENT CURRENT vs SUPPLY VOLTAGE 30 Per Amplifier
QUIESCENT CURRENT vs TEMPERATURE 30 25 Per Amplifier VS = +5V
Quiescent Current (µA)
25
Quiescent Current (µA)
20 15 10 5 VS = +2.3V
20
15
10 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V)
0 –75 –50 –25 0 25 50 75 100 125 Temperature (°C)
SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE ±6 ±5 ±4 ±3 ±2 –ISC ±1 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) +ISC 8 7 Short-Circuit Current (mA) 6
SHORT-CIRCUIT CURRENT vs TEMPERATURE
Short-Circuit Current (mA)
VS = +5V –ISC
5 4 3 2 1 0 –75 –50 –25 0 25 50 75 100 125 Temperature (°C) +ISC VS = +2.3V –ISC +ISC
4
OPA336, 2336, 4336
www.ti.com
SBOS068B
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VS = +5V, and RL = 25kΩ connected to VS/2, unless otherwise noted.
INPUT VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY 1k Voltage Noise
Voltage Noise (nV/√Hz) Current Noise (fA/√Hz)
CHANNEL SEPARATION vs FREQUENCY
1k
150
Channel Separation (dB)
140
100
100
130 Dual and Quad devices, G = 1, all channels. Quad measured channel A to D or B to C—other combinations yield improved rejection. 100 1k Frequency (Hz) 10k 100k
10
10
120
Current Noise 1 1 10 100 1k 10k 100k Frequency (Hz)
110
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 6 5 VS = +5.5V
120
AOL, CMRR, PSRR vs TEMPERATURE AOL
4 3 VS = +2.3V 2 1 0 100 1k Frequency (Hz) 10k 100k
AOL, CMRR, PSRR (dB)
110
Output Voltage (Vp-p)
100 PSRR 90 CMRR 80
70 –75 –50 –25 0 25 50 75 100 125 Temperature (°C)
OFFSET VOLTAGE PRODUCTION DISTRIBUTION 25 Typical production distribution of packaged units. 25
OFFSET VOLTAGE DRIFT MAGNITUDE PRODUCTION DISTRIBUTION Typical production distribution of packaged units.
Percent of Amplifiers (%)
15
Percent of Amplifiers (%)
20
20
15
10
10
5
0.1% 0.3%
0.2% 0.1%
5
0
–500 –400 –300 –200 –100 0 100 200 300 400 500
0
0.25 0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5 2.75 3 3.25 3.5 3.75 4
Offset Voltage (µV)
Offset Voltage Drift (µV/°C)
OPA336, 2336, 4336
SBOS068B
www.ti.com
5
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VS = +5V, and RL = 25kΩ connected to VS/2, unless otherwise noted.
INPUT BIAS CURRENT vs TEMPERATURE 1k
4
INPUT BIAS CURRENT vs INPUT COMMON-MODE VOLTAGE
Input Bias Current (pA)
Input Bias Current (pA)
100
3 VS = +5V 2
10
1
1
0.1 –75 –50 –25 0 25 50 Temperature (°C) 75 100 125
0 0 1 2 3 Common-Mode Voltage (V) 4 5
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT 5 VS = +5V 4 –2.5
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT VS = ±2.5V –2.0 Sinking Current –1.5 +125°C –1.0 –55°C –0.5 +25°C
Output Voltage (V)
+25°C
3 VS = +2.3V 2 –55°C 1 +25°C 0 0 1 2 3 4 5 Output Current (mA) 6 7 8 +125°C
Output Voltage (V)
Sourcing Current
–55°C
+125°C
0 –0 –1 –2 –3 –4 –5 Output Current (mA) –6 –7 –8
SMALL-SIGNAL STEP RESPONSE G = 1, CL = 200pF, VS = +5V
LARGE-SIGNAL STEP RESPONSE G = 1, CL = 620pF, VS = +5V
500mV/div
20mV/div
50µs/div
200µs/div
6
OPA336, 2336, 4336
www.ti.com
SBOS068B
APPLICATIONS INFORMATION
OPA336 series op amps are fabricated on a state-of-the-art 0.6 micron CMOS process. They are unity-gain stable and suitable for a wide range of general-purpose applications. Power-supply pins should be bypassed with 0.01µF ceramic capacitors. OPA336 series op amps are protected against reverse battery voltages. OPERATING VOLTAGE OPA336 series op amps can operate from a +2.1V to +5.5V single supply with excellent performance. Most behavior remains unchanged throughout the full operating voltage range. Parameters which vary significantly with operating voltage are shown in the typical characteristics. OPA336 series op amps are fully specified for operation from +2.3V to +5.5V; a single limit applies over the supply range. In addition, many parameters are guaranteed over the specified temperature range, –40°C to +85°C. INPUT VOLTAGE The input common-mode range of OPA336 series op amps extends from (V–) – 0.2V to (V+) – 1V. For normal operation, inputs should be limited to this range. The absolute maximum input voltage is 300mV beyond the supplies. Thus, inputs greater than the input common-mode range but less than maximum input voltage, while not valid, will not cause any damage to the op amp. Furthermore, the inputs may go beyond the power supplies without phase inversion, as shown in Figure 1, unlike some other op amps.
Normally, input bias current is approximately 1pA. However, input voltages exceeding the power supplies can cause excessive current to flow in or out of the input pins. Momentary voltages greater than the power supply can be tolerated as long as the current on the input pins is limited to 10mA. This is easily accomplished with an input resistor, as shown in Figure 2.
+5V IOVERLOAD 10mA max VIN 5kΩ
OPAx336
VOUT
FIGURE 2. Input Current Protection for Voltages Exceeding the Supply Voltage. CAPACITIVE LOAD AND STABILITY OPA336 series op amps can drive a wide range of capacitive loads. However, all op amps under certain conditions may become unstable. Op-amp configuration, gain, and load value are just a few of the factors to consider when determining stability. When properly configured, OPA336 series op amps can drive approximately 10,000pF. An op amp in unity-gain configuration is the most vulnerable to capacitive load. The capacitive load reacts with the op amp’s output resistance, along with any additional load resistance, to create a pole in the response which degrades the phase margin. In unity gain, OPA336 series op amps perform well with a pure capacitive load up to about 300pF. Increasing gain enhances the amplifier’s ability to drive loads beyond this level. One method of improving capacitive load drive in the unity-gain configuration is to insert a 50Ω to 100Ω resistor inside the feedback loop, as shown in Figure 3. This reduces ringing with large capacitive loads while maintaining DC
6V
VOUT
RS 100Ω OPAx336
0V
VOUT CL RL
VIN
FIGURE 1. No Phase Inversion with Inputs Greater than the Power-Supply Voltage.
FIGURE 3. Series Resistor in Unity-Gain Configuration Improves Capacitive Load Drive.
OPA336, 2336, 4336
SBOS068B
www.ti.com
7
accuracy. For example, with RL = 25kΩ, OPA336 series op amps perform well with capacitive loads in excess of 1000pF, as shown in Figure 4. Without RS, capacitive load drive is typically 350pF for these conditions, as shown in Figure 5.
Direct Current (DC) error at the output, however, this error may be insignificant. For instance, with RL = 100kΩ and RS = 100Ω, there is only about a 0.1% error at the output. Figure 5 shows the recommended operating regions for the OPA336. Decreasing the load resistance generally improves capacitive load drive. Figure 5 also illustrates how stability differs depending on where the resistive load is connected. With G = +1 and RL = 10kΩ connected to VS/2, the OPA336 can typically drive 500pF. Connecting the same load to ground improves capacitive load drive to 1000pF.
RS = 100Ω, Load = 2kΩ || 1000pF, VS = +5V
20mV/div
10k Operation Above Selected Gain Curve Not Recommended
Capacitive Load (pF)
G = +1 RL to Ground 1k
G = +2 RL to Ground
50µs/div
FIGURE 4. Small-Signal Step Response Using Series Resistor to Improve Capacitive Load Drive. Alternatively, the resistor may be connected in series with the output outside of the feedback loop. However, if there is a resistive load parallel to the capacitive load, it and the series resistor create a voltage divider. This introduces a
G = +1 RL to VS/2 100 5 10
VS = +5V, VO = VS/2 100
Resistive Load (kΩ)
FIGURE 5. Stability—Capacitive Load vs Resistive Load.
8
OPA336, 2336, 4336
www.ti.com
SBOS068B
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2004
PACKAGING INFORMATION
Orderable Device OPA2336E/250 OPA2336E/2K5 OPA2336EA/250 OPA2336EA/2K5 OPA2336P OPA2336PA OPA2336U OPA2336U/2K5 OPA2336UA OPA2336UA/2K5 OPA336N/250 OPA336N/3K OPA336NA/250 OPA336NA/3K OPA336NJ/250 OPA336NJ/3K OPA336P OPA336PA OPA336U OPA336U/2K5 OPA336UA OPA336UA/2K5 OPA336UJ OPA336UJ/2K5 OPA4336EA/250 OPA4336EA/2K5 OPA4336PA
(1)
Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE OBSOLETE OBSOLETE ACTIVE ACTIVE ACTIVE ACTIVE PREVIEW PREVIEW ACTIVE ACTIVE OBSOLETE
Package Type MSOP MSOP MSOP MSOP PDIP PDIP SOIC SOIC SOIC SOIC SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 PDIP PDIP SOIC SOIC SOIC SOIC SOIC SOIC SSOP/ QSOP SSOP/ QSOP PDIP
Package Drawing DGK DGK DGK DGK P P D D D D DBV DBV DBV DBV DBV DBV P P D D D D D D DBQ DBQ N
Pins Package Eco Plan (2) Qty 8 8 8 8 8 8 8 8 8 8 5 5 5 5 5 5 8 8 8 8 8 8 8 8 16 16 14 100 2500 100 2500 100 2500 250 2500 250 2500 250 2500 50 50 100 2500 100 2500 250 3000 250 3000 250 3000 None None None None None None None None None None None None None None None None None None None None None None None None None None None
Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU Call TI Call TI CU SNPB CU SNPB CU SNPB CU SNPB CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU Call TI Call TI CU SNPB CU SNPB CU SNPB CU SNPB Call TI Call TI CU NIPDAU CU NIPDAU Call TI
MSL Peak Temp (3) Level-1-235C-UNLIM Level-1-235C-UNLIM Level-1-235C-UNLIM Level-1-235C-UNLIM Level-NA-NA-NA Level-NA-NA-NA Level-2-220C-1 YEAR Level-2-220C-1 YEAR Level-2-220C-1 YEAR Level-2-220C-1 YEAR Level-1-235C-UNLIM Level-1-235C-UNLIM Level-1-235C-UNLIM Level-1-235C-UNLIM Level-3-220C-168 HR Level-3-220C-168 HR Call TI Call TI Level-2-220C-1 YEAR Level-2-220C-1 YEAR Level-2-220C-1 YEAR Level-2-220C-1 YEAR Call TI Call TI Level-3-240C-168 HR Level-3-240C-168 HR Call TI
The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2004
temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
0.400 (10,60) 0.355 (9,02) 8 5
PLASTIC DUAL-IN-LINE
0.260 (6,60) 0.240 (6,10)
1
4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.015 (0,38) 0.200 (5,08) MAX Seating Plane 0.125 (3,18) MIN 0.010 (0,25) NOM Gage Plane
0.020 (0,51) MIN
0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) M
0.430 (10,92) MAX
4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MSOI004E JANUARY 1995 − REVISED MAY 2002
DBQ (R−PDSO−G**)
PLASTIC SMALL−OUTLINE PACKAGE
0.025 (0,64) 24
0.012 (0,30) 0.008 (0,20) 13
0.005 (0,13)
0.157 (3,99) 0.150 (3,81)
0.244 (6,20) 0.228 (5,80)
0.008 (0,20) NOM
Gauge Plane 1 A 0°−8° 0.069 (1,75) MAX 12 0.010 (0,25) 0.035 (0,89) 0.016 (0,40)
Seating Plane 0.010 (0,25) 0.004 (0,10) 0.004 (0,10)
PINS ** DIM A MAX
16 0.197 (5,00) 0.189 (4,80)
20 0.344 (8,74) 0.337 (8,56)
24 0.344 (8,74) 0.337 (8,56)
28 0.394 (10,01) 0.386 (9,80)
A MIN
D
M0−137 VARIATION
AB
AD
AE
AF
4073301/F 02/2002 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). D. Falls within JEDEC MO−137.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2004, Texas Instruments Incorporated www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless