PCM1737E

® PCM 173 7 PCM1737 For most current data sheet and other product information, visit www.burr-brown.com 24-Bit, 192kHz Sampling Enhanced Multi-Level, Delta-Sigma, Audio DIGITAL-TO-ANALOG CONVERTER TM FEATURES q 24-BIT RESOLUTION q ANALOG PERFORMANCE (VCC = +5V): Dynamic Range: 106dB typ SNR: 106dB typ THD+N: 0.0015% typ Full-Scale Output: 3.1Vp-p typ q 4x/8x OVERSAMPLING DIGITAL FILTER: Passband: 0.454fS Stopband: 0.546fS Stopband Attenuation: –82dB Passband Ripple: ±0.002dB q SAMPLING FREQUENCY: 10kHz to 192kHz q SYSTEM CLOCK: 128, 192, 256, 384, 512, or 768fS with Auto Detect q ACCEPTS 16-, 18-, 20-, AND 24-BIT AUDIO DATA q DATA FORMATS: Standard, I2S, and Left-Justified q USER-PROGRAMMABLE MODE CONTROLS: Digital Attenuation: 0dB to –63dB, 0.5dB/Step Digital De-Emphasis Digital Filter Roll-Off: Sharp or Slow Soft Mute Variable Oversampling for ∆Σ DACs Zero Detect Mute Zero Flags for Each Output q DUAL SUPPLY OPERATION: +5V Analog, +3.3V Digital q 5V TOLERANT DIGITAL INPUTS q SMALL SSOP-28 PACKAGE APPLICATIONS q A/V RECEIVERS q DVD MOVIE AND AUDIO PLAYERS q DVD ADD-ON CARDS FOR HIGH-END PCs q HDTV RECEIVERS q CAR AUDIO SYSTEMS q OTHER APPLICATIONS REQUIRING 24-BIT AUDIO DESCRIPTION The PCM1737 is a CMOS, monolithic, integrated circuit which includes stereo digital-to-analog converters and support circuitry in a small SSOP-28 package. The data converters utilize Burr-Brown’s enhanced multi-level delta-sigma architecture, which employs 4th-order noise shaping and 8-level amplitude quantization to achieve excellent dynamic performance and improved tolerance to clock jitter. The PCM1737 accepts industry standard audio data formats with 16- to 24-bit data, providing easy interfacing to audio DSP and decoder chips. Sampling rates up to 192kHz are supported. A full set of user-programmable functions are accessible through a 4-wire serial control port which supports register write and read back functions. International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 © 1999 Burr-Brown Corporation PDS-1552C Printed in U.S.A. March, 2000 SPECIFICATIONS All specifications at +25°C, +VCC = +5V, +VDD = +3.3V, system clock = 384fS (fS = 44.1kHz) and 24-bit data, unless otherwise noted. PCM1737E PARAMETER RESOLUTION DATA FORMAT Audio Data Interface Formats Audio Data Bit Length Audio Data Format System Clock Frequency Sampling Frequency (fS) DIGITAL INPUT/OUTPUT Logic Family Input Logic Level VIH VIL Input Logic Current IIH IIL IIH(1) IIL(1) Output Logic Current, Pin 25 (MDO) IIZH IIZL Output Logic Level VOH(2) VOL(2) VOH(3) VOL(3) DYNAMIC PERFORMANCE(4) THD+N, VOUT = 0dB User Selectable User Selectable CONDITIONS MIN TYP 24 Standard, I2S, Left-Justified 16-, 18-, 20-, 24-Bit MSB-First, Binary Two’s Complement 128, 192, 256, 384, 512, 768fS 10 200 TTL-Compatible 2.0 0.8 VIN = VDD VIN = 0V VIN = VDD VIN = 0V At Output Disable, VIN = VDD At Output Disable, VIN = 0V IOH = –2mA IOL = +2mA IOH = –4mA IOL = +4mA fS = 44.1kHz, SCLK = 384fS fS = 96kHz, SCLK = 256fS fS = 192kHz, SCLK = 128fS fS = 44.1kHz fS = 96kHz fS = 192kHz EIAJ, A-Weighted, fS =44.1kHz A-Weighted, fS = 96kHz A-Weighted, fS =192kHz EIAJ, A-Weighted, fS =44.1kHz A-Weighted, fS = 96kHz A-Weighted, fS = 192kHz fS = 44.1kHz fS = 96kHz fS = 192kHz 2.4 1.0 2.4 1.0 0.0015 0.0020 0.0025 0.6 0.7 0.8 106 105 104 105 104 104 102 101 102 ±1.0 ±1.0 ±30 62% of VCC 50% VCC 5 0.0035 0.0050 0.0060 0.8 1.0 1.2 0.1 –0.1 100 –0.1 2.0 –0.1 V V µA µA µA µA µA µA V V V V % % % % % % dB dB dB dB dB dB dB dB dB % of FSR % of FSR mV Vp-p V kΩ MAX UNITS Bits kHz 65 VOUT = –60dB Dynamic Range Signal-to-Noise Ratio(5) Channel Separation 102 100 98 100 100 100 96 96 DC ACCURACY Gain Error Gain Mismatch, Channel-to-Channel Bipolar Zero Error ANALOG OUTPUT Output Voltage Center Voltage Load Impedance DIGITAL FILTER PERFORMANCE Filter Characteristic, Sharp Roll-Off Passband Stopband Passband Ripple Stopband Attenuation Filter Characteristics, Slow Roll-Off 1 Passband Stopband Passband Ripple Stopband Attenuation VO = 0.5VCC at Bipolar Zero Full Scale (0dB) AC Load ±3.0 ±3.0 ±60 ±0.002dB –3dB 0.546fS Stopband = 0.546fS Stopband = 0.567fS ±0.002dB –3dB 0.732fS Stopband = 0.732fS –82 –75 –82 0.454fS 0.490fS ±0.002 Hz Hz Hz dB dB dB Hz Hz Hz dB dB 0.274fS 0.454fS ±0.002 The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® PCM1737 2 SPECIFICATIONS (Cont.) All specifications at +25°C, +VCC = +5V, +VDD = +3.3V, system clock = 384fS (fS = 44.1kHz) and 24-bit data, unless otherwise noted. PCM1737E PARAMETER DIGITAL FILTER PERFORMANCE (cont.) Filter Characteristics, Slow Roll-Off 2 Passband Stopband Passband Ripple Stopband Attenuation Delay Time De-Emphasis Error ANALOG FILTER PERFORMANCE Frequency Response Cut-Off Frequency POWER SUPPLY REQUIREMENTS Voltage Range VDD VCC Supply Current IDD(6) CONDITIONS MIN TYP MAX UNITS ± 0.01dB –3dB 0.952f S Stopband = 0.732fS –49 34/fS ±0.1 f = 20kHz f = 44kHz –3dB –0.03 –0.20 190 0.072fS 0.363fS ±0.002 Hz Hz Hz dB dB sec dB dB dB kHz +3.0 +4.5 VDD = +3.3V fS = 44.1kHz fS = 96kHz, 256fS f S = 192kHz, 128fS VCC = 5.0V fS = 44.1kHz fS = 96kHz, 256fS f S = 192kHz, 128fS VDD = 3.3V, VCC = 5.0V fS = 44.1kHz fS = 96kHz, 256fS f S = 192kHz, 128fS 0 –55 +3.3 +5.0 +3.6 +5.5 V V 8.5 16.5 19.5 13.0 14.0 14.5 93 124 137 12.0 mA mA mA mA mA mA mW mW mW °C °C °C/W ICC 18.0 Power Dissipation 130 TEMPERATURE RANGE Operation Storage Thermal Resistance, θJA +70 +125 100 NOTES: (1) Pins 8, 9, 26, 27, 28 (TEST1, TEST2, MDI, MC, ML). (2) Pins 23, 24 (ZEROL, ZEROR). (3) Pin 4 (CLKO). (4) Analog performance specifications are tested with Shibasoku #725 THD Meter 400Hz, HPF on, 30kHz LPF on, average mode with 20kHz bandwidth limiting. The load connected to the analog output is 5kΩ or larger, AC-coupled. (5) SNR is tested with Infinite Zero Detection off. (6) CLKO is disabled. ABSOLUTE MAXIMUM RATINGS Power Supply Voltage, +VDD ............................................................ +4.0V +VCC ............................................................ +6.5V +VCC to +VDD Difference ................................................................... ±0.1V Digital Input Voltage ........................................................... –0.2V to +5.5V Digital Output Voltage(1) ........................................... –0.2V to (VDD + 0.2V) Input Current (except power supply) ............................................... ±10mA Power Dissipation .......................................................................... 650mW Operating Temperature Range ............................................. 0°C to +70°C Storage Temperature ...................................................... –55°C to +125°C Lead Temperature (soldering, 5s) ................................................. +260°C Package Temperature (IR reflow, 10s) .......................................... +235°C ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PACKAGE DRAWING NUMBER 324 SPECIFIED TEMPERATURE RANGE 0°C to +70°C PACKAGE MARKING PCM1737E ORDERING NUMBER(1) PCM1737E PCM1737E/2K TRANSPORT MEDIA Rails Tape and Reel PRODUCT PCM1737E PACKAGE 28-Lead SSOP " " " " " NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K indicates 2000 devices per reel). Ordering 2000 pieces of “PCM1737E/2K” will get a single 2000-piece Tape and Reel. ® 3 PCM1737 BLOCK DIAGRAM PCM1737 BCLK LRCK Audio Serial I/F DAC Output Amp and Low-Pass Filter VOUTL VCOML DATA TEST1 TEST2 RSTB ML MC MDI MDO Mode Control I/F 4x/8x Oversampling Digital Filter with Function Controller Enhanced Multi-level Delta-Sigma Modulator DAC Output Amp and Low-Pass Filter VOUTR VCOMR System Clock System Clock Manager Power Supply SCLK Zero Detect VDD VSS ZEROL ZEROR GNDA GNDL PIN CONFIGURATION Top View SSOP PIN ASSIGNMENTS PIN 1 2 3 4 NAME LRCK DATA BCLK CLKO SCLK VSS VDD TEST1 TEST2 VCCR GNDR VCOMR VOUTR GNDA VCCA VOUTL VCOML GNDL VCCL NC NC RSTB ZEROL ZEROR MDO MDI MC ML I/O I I I O I — — I I — — — O — — O — — — — — I O O O I I I DESCRIPTION Left/Right Word Clock(1) Data In for Left/Right Channels(1) Bit Clock(1) System Clock Output System Clock Input(1) Digital Ground Digital Supply, +3.3V. Test Pin(2). Must be connected to ground (VSS). Test Pin(2). Must be connected to ground (VSS). Analog Supply for Right Channel, +5V Analog Ground for Right Channel Common for Right Channel Analog Output for Right Channel Analog Ground Analog Supply, +5V Analog Output for Left Channel Common for Left Channel Analog Ground for Left Channel Analog Supply for Left Channel, +5V Not Connected Not Connected Reset, Active Low(2). Zero Flag for Left Channel Zero Flag for Right Channel Mode Data Out(3) Mode Data In(2) Mode Clock(2) Mode Latch(2) LRCK DATA BCLK CLKO SCLK VSS VDD TEST1 TEST2 VCCR GNDR VCOMR VOUTR GNDA 1 2 3 4 5 6 7 PCM1737E 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 ML MC MDI MDO ZEROR 5 6 7 8 9 10 ZEROL RSTB NC NC VCCL GNDL VCOML VOUTL VCCA 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 NOTES: (1) Schmitt-Trigger input, 5V tolerant. (2) Schmitt-Trigger input with internal pull-down, 5V tolerant. (3) Tri-state output. ® PCM1737 4 GNDR VCCA VCCL VCCR CLKO TYPICAL PERFORMANCE CURVES All specifications at TA = +25°C, VDD = VCC = 5V, SYSCLK = 384fS (fS = 44.1kHz), and 24-bit input data, unless otherwise noted. DIGITAL FILTER Digital Filter (De-Emphasis Off, fS = 44.1kHz) FREQUENCY RESPONSE (Sharp Roll-Off) 0 –20 –40 PASSBAND RIPPLE (Sharp Roll-Off) 0.003 0.002 Amplitude (dB) 0.001 0 –0.001 –0.002 Amplitude (dB) –60 –80 –100 –120 –140 –160 –0.003 0 0.5 1 1.5 2 2.5 3 3.5 4 0 0.1 0.2 0.3 0.4 0.5 Frequency (x fS) Frequency (x fS) FREQUENCY RESPONSE (Slow Roll-Off 1) 0 –20 –40 Amplitude (dB) Amplitude (dB) –60 –80 –100 –120 –140 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Frequency (x fS) 0 –2 –4 –6 –8 –10 –12 –14 –16 –18 –20 0 0.1 TRANSITION CHARACTERISTICS (Slow Roll-Off 1) 0.2 0.3 Frequency (x fS) 0.4 0.5 0.6 FREQUENCY RESPONSE (Slow Roll-Off 2) 0 –20 –40 Amplitude (dB) –60 –80 –100 –120 –140 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Frequency (x fS) 0 –1 –2 Amplitude (dB) –3 –4 –5 –6 –7 –8 –9 –10 0 0.1 TRANSITION CHARACTERISTICS (Slow Roll-Off 2) 0.2 0.3 Frequency (x fS) 0.4 0.5 0.6 ® 5 PCM1737 TYPICAL PERFORMANCE CURVES (Cont.) All specifications at TA = +25°C, VDD = VCC = 5V, SYSCLK = 384fS (fS = 44.1kHz), and 24-bit input data, unless otherwise noted. DIGITAL FILTER De-Emphasis Error 0 –2 –4 –6 –8 –10 0 DE-EMPHASIS FREQUENCY RESPONSE (fS = 32kHz) Level (dB) 0.5 0.3 0.1 –0.1 –0.3 –0.5 0 2 DE-EMPHASIS ERROR (fS = 32kHz) Level (dB) 2 4 6 8 10 12 14 4 6 8 10 12 14 Frequency (kHz) DE-EMPHASIS FREQUENCY RESPONSE (fS = 44.1kHz) Level (dB) Frequency (kHz) DE-EMPHASIS ERROR (fS = 44.1kHz) 0 –2 –4 –6 –8 –10 0 0.5 0.3 0.1 –0.1 –0.3 –0.5 0 2 Level (dB) 2 4 6 8 10 12 14 16 18 20 4 6 8 10 12 14 16 18 20 Frequency (kHz) DE-EMPHASIS FREQUENCY RESPONSE (fS = 48kHz) Level (dB) Frequency (kHz) DE-EMPHASIS ERR0R (fS = 48kHz) 0 –2 –4 –6 –8 –10 0 0.5 0.3 0.1 –0.1 –0.3 –0.5 0 2 4 Level (dB) 2 4 6 8 10 12 14 16 18 20 22 6 8 10 12 14 16 18 20 22 Frequency (kHz) Frequency (kHz) ANALOG DYNAMIC PERFORMANCE Supply Voltage Characteristics TOTAL HARMONIC DISTORTION + NOISE vs VCC (VDD = 3.3V) 10 192kHz, 128fS 1 110 108 Dynamic Range (dB) –60dB 44.1kHz, 384fS DYNAMIC RANGE vs VCC (VDD = 3.3V) 44.1kHz, 384fS 106 104 102 100 98 192kHz, 128fS THD+N (%) 0.1 0.01 192kHz, 128fS 0dB 44.1kHz, 384fS 0.001 0.0001 4.0 4.5 5.0 VCC (V) 5.5 6.0 96 4.0 4.5 5.0 VCC (V) 5.5 6.0 ® PCM1737 6 TYPICAL PERFORMANCE CURVES (Cont.) All specifications at TA = +25°C, VDD = VCC = 5V, SYSCLK = 384fS (fS = 44.1kHz), and 24-bit input data, unless otherwise noted. ANALOG DYNAMIC PERFORMANCE (con.t) Supply Voltage Characteristics SIGNAL-TO-NOISE RATIO vs VCC (VDD = 3.3V) CHANNEL SEPARATION vs VCC 110 108 110 108 106 SNR (dB) 104 102 100 98 96 4.0 44.1kHz, 384fS Channel Separation (dB) 106 104 102 100 98 96 44.1kHz, 384fS 192kHz, 128fS 192kHz, 128fS 4.5 5.0 VCC (V) 5.5 6.0 4.0 4.5 5.0 VCC (V) 5.5 6.0 Temperature Characteristics TOTAL HARMONIC DISTORTION + NOISE vs TEMPERATURE 10 192kHz, 128fS 1 Dynamic Range (dB) 110 108 –60dB 44.1kHz, 384fS 192kHz, 128fS DYNAMIC RANGE vs TEMPERATURE (VDD = 3.3V) 44.1kHz, 384fS 106 104 102 192kHz, 128fS 100 98 96 THD+N (%) 0.1 0.01 0dB 0.001 44.1kHz, 384fS 0.0001 4.0 4.5 5.0 VCC (V) 5.5 6.0 –25 0 25 50 75 100 Temperature (°C) SIGNAL-TO-NOISE RATIO vs TEMPERATURE (VDD = 3.3V) 110 108 106 SNR (dB) 110 108 CHANNEL SEPARATION vs TEMPERATURE (VDD = 3.3V) 44.1kHz, 384fS Channel Separation (dB) 106 104 102 100 98 96 44.1kHz, 384fS 104 102 100 98 96 –25 0 25 50 75 100 Temperature (°C) 192kHz, 128fS 192kHz, 128fS –25 0 25 50 75 100 Temperature (°C) ® 7 PCM1737 SYSTEM CLOCK AND RESET FUNCTIONS SYSTEM CLOCK INPUT The PCM1737 requires a system clock for operating the digital interpolation filters and multi-level delta-sigma modulators. The system clock is applied at the SCLK input (pin 5). Table I shows examples of system clock frequencies for common audio sampling rates. Figure 1 shows the timing requirements for the system clock input. For optimal performance, it is important to use a clock source with low phase jitter and noise. Burr-Brown’s PLL1700 multi-clock generator is an excellent choice for providing the PCM1737 system clock. SYSTEM CLOCK OUTPUT A buffered version of system clock input is available at the CLKO output (pin 4). CLKO can operate at either full (fSCLK) or half (fSCLK/2) rate. The CLKO output frequency may be programmed using the CLKD bit of Control Register 20. The CLKO output pin can also be enabled or disabled using the CLKE bit of Control Register 20. The default is CLKO enabled. POWER-ON AND EXTERNAL RESET FUNCTIONS The PCM1737 includes a power-on reset function. Figure 2 shows the operation of this function. The system clock input at SCLK should be active for at least one clock period prior to VDD = 2.0V. With the system clock active and VDD > 2.0V, the power-on reset function will be enabled. The initialization sequence requires 1024 system clocks from the time VDD > 2.0V. After the initialization period, the PCM1737 will be set to its reset default state, as described in the Mode Control Register section of this data sheet. The PCM1737 also includes an external reset capability using the RSTB input (pin 22). This allows an external controller or master reset circuit to force the PCM1737 to initialize to its reset default state. Figure 3 shows the external reset operation and timing. The RSTB pin is set to logic ‘0’ for a minimum of 20ns. The RSTB pin is then set to a logic “1” state, which starts the initialization sequence which lasts for 1024 system clock periods. After the initialization sequence is complete, the PCM1737 will be set to its reset default state, as described in the Mode Control Register section of this data sheet. SYSTEM CLOCK FREQUENCY (fSCLK) (MHz) SAMPLING FREQUENCY (fS) 16kHz 32kHz 44.1kHz 48kHz 88.2kHz 96kHz 176.4kHz 192 128fS — — — — — 12.2880 22.5792 24.5760 192fS — — — — — 18.4320 33.8688 36.8640 256fS 4.0960 8.1920 11.2896 12.2880 22.5792 24.5760 See Note 2 See Note 2 384fS 6.1440 12.2880 16.9344 18.4320 33.8688 36.8640 See Note 2 See Note 2 512fS 8.1920 16.3840 22.5792 24.5760 45.1584 49.1520 See Note 2 See Note 2 768fS 12.2880 24.5760 33.8688 36.8640 See Note 1 See Note 1 See Note 2 See Note 2 NOTE: (1) The 768fS system clock rate is not supported for fS > 64kHz. (2) This system clock rate is not supported for the given sampling frequency. TABLE I. System Clock Rates for Common Audio Sampling Frequencies. tSCLKH “H” SCLK “L” tSCLKL System Clock Pulse Width High tSCLKH System Clock Pulse Width Low tSCLKL fSCLK : 7ns min : 7ns min 0.8V 2.0V FIGURE 1. System Clock Input Timing. ® PCM1737 8 The external reset is especially useful in applications where there is a delay between PCM1737 power up and system clock activation. In this case, the RSTB pin should be held at a logic ‘0’ level until the system clock has been activated. The RSTB pin may then be set to a logic ‘1” state to start the initialization sequence. AUDIO SERIAL INTERFACE The audio serial interface for the PCM1737 is comprised of a 3-wire synchronous serial port. It includes LRCK (pin 1), BCLK (pin 3), and DATA (pin 2). BCLK is the serial audio bit clock, and it is used to clock the serial data present on DATA into the audio interface’s serial shift register. Serial data is clocked into the PCM1737 on the rising edge of BCLK. LRCK is the serial audio left/right word clock. It is used to latch serial data into the serial audio interface’s internal registers. Both LRCK and BCLK must be synchronous to the system clock. Ideally, it is recommended that LRCK and BCLK be derived from the system clock input or output, SCLK or CLKO. The left/right clock, LRCK, is operated at the sampling frequency, fS. The bit clock, BCLK, may be operated at 48 or 64 times the sampling frequency. Audio Data Formats and Timing The PCM1737 supports industry-standard audio data formats, including standard, I2S, and left-justified. The data formats are shown in Figure 4. Data formats are selected using the format bits, FMT[2:0], in Control Register 20. The default data format is 24-bit standard. All formats require Binary Two’s Complement, MSB-first audio data. Figure 5 shows a detailed timing diagram for the serial audio interface. SERIAL CONTROL INTERFACE The serial control interface is a 4-wire serial port which operates asynchronously to the serial audio interface. The serial control interface is utilized to program and read the onchip mode registers. The control interface includes MDO (pin 25), MDI (pin 26), MC (pin 27), and ML (pin 28). MDO is the serial data output, used to read back the values of the mode registers. MDI is the serial data input, used to program the mode registers. MC is the serial bit clock, used to shift data in and out of the control port. ML is the control port latch clock. 2.4V VCC = VDD 2.0V 1.6V Reset Reset Removal Internal Reset 1024 system clocks System Clock (SCLK) FIGURE 2. Power-On Reset Timing. RSTB tRST(1) Reset Reset Removal Internal Reset 1024 system clocks System Clock (SCLK) NOTE: (1) tRST = 20ns min. FIGURE 3. External Reset Timing. ® 9 PCM1737 (1) Standard Data Format; Lch = HIGH, Rch = LOW 1/fS Lch Rch LRCK ® BCLK (= 48fS or 64fS) 14 15 16 1 1 14 15 16 LSB 16 17 18 LSB 18 19 20 LSB 22 23 24 LSB MSB 1 MSB 1 MSB 1 4 5 MSB 2 3 2 3 2 3 2 3 MSB 16 17 18 1 16 17 18 LSB 18 19 20 LSB 22 23 24 LSB MSB 18 19 20 1 MSB 22 23 24 1 4 5 MSB 2 3 2 3 2 3 LSB 2 3 14 15 16 PCM1737 1/fS Lch Rch 1 1 MSB 2 2 3 22 23 24 3 22 23 24 LSB 1/fS Lch Rch 1 MSB 2 3 22 23 24 LSB 1 MSB 2 3 22 23 24 LSB 1 2 16-Bit Right-Justified DATA 18-Bit Right-Justified DATA 20-Bit Right-Justified DATA 24-Bit Right-Justified DATA 10 (2) 24-Bit Left-Justified Data Format; Lch = HIGH, Rch = LOW LRCK BCLK (= 48fS or 64fS) DATA (3) 24-Bit I2S Data Format; Lch = LOW, Rch = HIGH LRCK BCLK (= 48fS or 64fS) DATA FIGURE 4. Audio Data Input Formats. REGISTER WRITE OPERATION All Write operations for the serial control port use 16-bit data words. Figure 6 shows the control data word format. The most significant bit is the Read/Write (R/W) bit. When set to ‘0’, this bit indicates a Write operation. There are seven bits, labeled IDX[6:0], that set the register index (or address) for the Write operation. The least significant eight bits, D[7:0], contain the data to be written to the register specified by IDX[6:0]. Figure 7 shows the functional timing diagram for writing the serial control port. ML is held at a logic ‘1’ state until a register needs to be written. To start the register write cycle, ML is set to logic ‘0’. Sixteen clocks are then provided on MC, corresponding to the 16 bits of the control data word on MDI. After the sixteenth clock cycle has completed, ML is set to logic ‘1’ to latch the data into the indexed mode control register. SINGLE REGISTER READ OPERATION Read operations utilize the 16-bit control word format shown in Figure 6. For Read operations, the Read/Write (R/W) bit is set to ‘1’. Read operations ignore the index bits, IDX[6:0], of the control data word. Instead, the REG[6:0] bits in Control Register 21 are used to set the index of the register that is to be read during the Read operation. Bits IDX[6:0] should be set to 00H for Read operations. LRCK tBCH BCK tBCY DATA1-DATA3 tDS tDH tBL tBCL tLB 50% of VDD 50% of VDD 50% of VDD SYMBOL t BCY t BCH t BCL t BL t LB t DS t DH PARAMETER BCK Pulse Cycle Time BCK High Level Time BCK Low Level Time BCK Rising Edge to LRCK Edge LRCK Falling Edge to BCK Rising Edge DIN Set Up Time DIN Hold Time MIN MAX 48 or 64fS (1) UNITS 35 35 10 10 10 10 ns ns ns ns ns ns NOTE: (1) fS is the sampling frequency (e.g., 44.1kHz, 48kHz, 96kHz, etc.) FIGURE 5. Audio Interface Timing. MSB R/W IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 D7 D6 D5 D4 D3 D2 D5 D4 D3 D2 D1 LSB D0 Register Index (or Address) Read/Write Operation 0 = Write Operation 1 = Read Operation (register index is ignored) Register Data FIGURE 6. Control Data Word Format for MDI. ML MC MDI X 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 D7 D6 D5 D4 D3 D2 D1 D0 X X D15 D14 FIGURE 7. Write Operation Timing. ® 11 PCM1737 I ML ® O MC I O MDI 0 1 REG6 REG5 REG4 REG3 REG2 REG1 REG0 I 0 0 0 Read Register Index High Impedance D7 Register Read Cycle D6 Writing Register 21 with INC and REG[6:0] Data D5 Read D4 X X 1 0 0 0 0 0 0 0 X X X X X 0 0 0 1 X X X PCM1737 D3 D2 D1 0 0 0 0 X X X X X X X X X X X X X X X X X X X X X X X X X D7 INDEX “1” D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 INDEX “N – 1” D1 D0 D7 D6 D5 D4 D3 INDEX “N” D2 D1 D0 O Write Data from Register Indexed by REG[6:0] D0 I MDO O X = Don't care FIGURE 8. Read Operation Timing with INC = 0 (Single Register Read). 12 High Impedance ML MC MDI 1 0 0 0 MDO High Impedance FIGURE 9. Read Operation Timing with INC = 1 (Auto-Increment Read). Figure 8 details the Read operation. First, Control Register 21 must be written with the index of the register to be read back. In addition, the INC bit must be set to logic ‘0’ in order to disable the auto-increment read function. The Read cycle is then initiated by setting ML to logic ‘0’ and setting the R/W bit of the control data word to logic ‘1’, indicating a Read operation. MDO remains at a high impedance state until the last 8 bits of the 16-bit read cycle, which corresponds to the 8 data bits of the register indexed by the REG[6:0] bits of Control Register 21. The Read cycle is complete when ML is set to ‘1’, immediately after the MC clock cycle for the least significant bit of indexed control register has completed. AUTO-INCREMENT READ OPERATION The Auto-Increment Read function allows for multiple registers to be read sequentially. The Auto-Increment function is enabled by setting the INC bit of Control Register 21 to ‘1’. The sequence always starts with Register 1, and ends with the register indexed by the REG[6:0] bits in Control Register 21. Figure 9 shows the timing for the Auto-Increment Read operation. The operation begins by writing Control Register 21, setting INC to ‘1’ and setting REG[6:0] to the last register to be read in the sequence. The actual Read operation starts on the next High to Low transition of the ML pin. The Read cycle starts by setting the R/W bit of the control word to ‘1’, and setting all of the IDX[6:0] bits to ‘0’. All subsequent bits input on the MDI are ignored while ML is set to ‘0’. For the first 8 clocks of the Read cycle, MDO is set to a high impedance state. This is followed by a sequence of 8-bit words, each corresponding the data contained in Control Registers 1 through N, where N is defined by the REG[6:0] bits in Control Register 21. The Read cycle is complete when ML is set to ‘1’, immediately after the MC clock cycle for the least significant bit of Control Register N has completed. CONTROL INTERFACE TIMING REQUIREMENTS Figure 10 shows a detailed timing diagram for the serial control interface. Pay special attention to the setup and hold times, as well as tMLS and tMLH, which define minimum delays between edges of the ML and MC clocks. These timing parameters are critical for proper control port operation. tMHH ML tMLS tMCH tMCL tMLH 50% of VDD tMCY LSB MDI tMOS MDO tMDS tMDI LSB 50% of VDD 50% of VDD 50% of VDD MC SYMBOL tMCY tMCL tMCH tMHH tMLS tMLH tMDI tMDS tMOS PARAMETER MC Pulse Cycle Time MC Low Level Time MC High Level Time ML High Level Time ML Falling Edge to MC Rising Edge ML Hold Time(1) Hold Time MDL Set Up Time MC Falling Edge to MDSO Stable MIN 100 50 50 300 20 20 15 20 MAX UNITS ns ns ns ns ns ns ns ns ns 30 NOTE: (1) MC rising edge for LSB to ML rising edge. FIGURE 10. Control Interface Timing. ® 13 PCM1737 MODE CONTROL REGISTERS User-Programmable Mode Controls The PCM1737 includes a number of user programmable functions which are accessed via control registers. The registers are programmed using the Serial Control Interface which was previously discussed in this data sheet. Table II lists the available mode control functions, along with their reset default conditions and associated register index. Register Map The mode control register map is shown in Table IV. Each register includes a R/W bit, which determines whether a register read (R/W =1) or write (R/W = 0) operation is performed. Each register also includes an index (or address) indicated by the IDX[6:0] bits. FUNCTION RESET DEFAULT REGISTER BIT(S) Digital Attenuation Control, 0dB to –63dB in 0.5dB Steps Soft Mute Control Digital Attenuation Speed Select Digital Attenuation Control Infinite Zero Detect Mute Oversampling Rate Control (64fS or 128fS) DAC Operation Control De-Emphasis Function Control De-Emphasis Sample Rate Selection Audio Data Format Control CLKO Output Enable CLKO Frequency Selection Digital Filter Roll-Off Control 4x/8x Digital Interpolation Control Read Register Index Control Read Auto-Increment Control 0dB, No Attenuation Mute Disabled 2/fS Attenuator Disabled Disabled 64fS Oversampling DAC1 and DAC2 Enabled De-Emphasis Disabled 44.1kHz 24-Bit Standard Format CLKO Enabled Full Rate (= fSCLK) Sharp Roll-Off 8x Interpolation REG[6:0] = 01H Auto-Increment Disabled 16 and 17 18 18 18 18 18 19 19 19 20 20 20 20 20 21 21 AT1[7:0] MUT[2:0] ATTS ATLD INZD OVER DAC[2:1] DM12 DMF[2:1] FMT[2:0] CLKE CLKD FLT[1:0] X4DS REG[6:0] INC TABLE II. User-Programmable Mode Controls. B15 Register 16 Register 17 Register 18 Register 19 Register 20 Register 21 R/W R/W R/W R/W R/W R/W B14 IDX6 IDX6 IDX6 IDX6 IDX6 IDX6 B13 IDX5 IDX5 IDX5 IDX5 IDX5 IDX5 B12 IDX4 IDX4 IDX4 IDX4 IDX4 IDX4 B11 IDX3 IDX3 IDX3 IDX3 IDX3 IDX3 B10 IDX2 IDX2 IDX2 IDX2 IDX2 IDX2 B9 IDX1 IDX1 IDX1 IDX1 IDX1 IDX1 B8 IDX0 IDX0 IDX0 IDX0 IDX0 IDX0 B7 AT17 AT27 res res X4DS INC B6 AT16 AT26 OVER DMF1 FLT1 REG6 B5 AT15 AT25 res DMF0 FLT0 REG5 B4 AT14 AT24 INZD DM12 CLKD REG4 B3 AT13 AT23 ATLD res CLKE REG3 B2 AT12 AT22 ATTS res FMT2 REG2 B1 AT11 AT21 B0 AT10 AT20 MUT2 MUT1 DAC2 DAC1 FMT1 FMT0 REG1 REG0 TABLE III. Mode Control Register Map. ® PCM1737 14 REGISTER DEFINITIONS B15 Register 16 Register 17 R/W R/W B14 IDX6 IDX6 B13 IDX5 IDX5 B12 IDX4 IDX4 B11 IDX3 IDX3 B10 IDX2 IDX2 B9 IDX1 IDX1 B8 IDX0 IDX0 B7 AT17 AT27 B6 AT16 AT26 B5 AT15 AT25 B4 AT14 AT24 B3 AT13 AT23 B2 AT12 AT22 B1 AT11 AT21 B0 AT10 AT20 R/W Read/Write Mode Select When R/W = 0, a Write operation is performed. When R/W = 1, a Read operation is performed. Default Value: 0 ATx[7:0] Digtial Attenuation Level Setting Where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR (x = 2). These bits are Read/Write. Default Value: 1111 1111B Each DAC output (VOUTL and VOUTR) has a digital attenuator associated with it. The attenuator may be set from 0dB to –63dB, in 0.5dB steps. Alternately, the attenuator may be set to infinite attenuation (or mute). The attenuation data for each channel can be set individually. However, the data load control (ATLD bit of Control Register 18) is common to both attenuators. ATLD must be set to ‘1’ in order to change an attenuator’s setting. The attenuation level may be set using the following formula: Attenuation Level (dB) = 0.5dB • (ATx[7:0]DEC – 255) Where: ATx[7:0]DEC = 0 through 255 For: ATx[7:0]DEC = 0 through 128, the attenuator is set to infinite attenuation. The following table shows attenuator levels for various settings: ATx[7:0] 1111 1111B 1111 1110B 1111 1101B • • • 1000 0010B 1000 0001B 1000 0000B • • • 0000 0000B Decimal Value 255 254 253 • • • 130 129 128 • • • 0 Attenuator Level Setting 0dB, No Attenuation (default) –0.5dB –1.0dB • • • –62.5dB –63.0dB Mute • • • Mute ® 15 PCM1737 B15 Register 18 R/W B14 IDX6 B13 IDX5 B12 IDX4 B11 IDX3 B10 IDX2 B9 IDX1 B8 IDX0 B7 res B6 OVER B5 res B4 INZD B3 ATLD B2 ATTS B1 B0 MUT2 MUT1 R/W Read/Write Mode Select When R/W = 0, a Write operation is performed. When R/W = 1, a Read operation is performed. Default Value: 0 Soft Mute Control Where, x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR ( x = 2). These bits are Read/Write. Default Value: 0 MUTx = 0 MUTx = 1 Mute Disabled (default) Mute Enabled MUTx The mute bits, MUT1 and MUT2, are used to enable or disable the Soft Mute function for the corresponding DAC outputs, VOUTL and VOUTR. The Soft Mute function is incorporated into the digital attenuators. When Mute is disabled (MUTx = 0), the attenuator and DAC operate normally. When Mute is enabled by setting MUTx = 1, the digital attenuator for the corresponding output will be decremented from the current setting to the infinite attenuation, one attenuator step (0.5dB) at a time, with the rate of change programmed by the ATTS bit. This provides ‘pop-free’ muting of the DAC output. By setting MUTx = 0, upon returning from Soft Mute, the attenuator will be incremented one step at a time to the previously-programeed attenuator level. ATTS Attenuation Rate Select This bit is Read/Write. Default Value: 0 ATTS = 0 ATTS = 1 Attenuation rate is 2/fS (default) Attenuation rate is 4/fS Changes in attenuator levels are made by incrementing or decrementing the attenuator by one step (0.5dB) for every 2/fS or 4/fS time interval until the programmed attenuator setting is reached. This helps to minimize audible ‘clicking’, or zipper noise while the attenuator is changing levels. The ATTS bit allows the user to select the rate at which the attenuator is decremented/incremented during level transitions. ATLD Attenuation Control This bit is Read/Write. Default Value: 0 ATLD = 0 ATLD = 1 Attenuator Disabled (default) Attenuator Enabled The ATLD bit must be set to logic ‘1’ in order for the attenuators to function. Setting ATLD to logic ‘0’ will disable the attenuator function and cause the current attenuator data to be lost. Set ATLD = 1 immediately after reset. ® PCM1737 16 Register 18 (cont.) INZD Infinite Zero Detect Mute Control This bit is Read/Write. Default Value: 0 INZD = 0 INZD = 1 Infinite Zero Detect Mute Disabled (default) Infinite Zero Detect Mute Enabled The INZD bit is used to enable or disable the Zero Detect Mute function described in the Zero Flag and Infinite Zero Detect Mute section in this data sheet. The Zero Detect Mute function is independent of the Zero Flag output operation, so enabling or disabling the INZD bit has no effect on the Zero Flag outputs (ZEROL and ZEROR). OVER Oversampling Rate Control This bit is Read/Write. Default Value: 0 OVER = 0 OVER = 1 64x Oversampling (default) 128x Oversampling Sets the oversampling rate of the delta-sigma D/A converters. The 128x setting can only be used for sampling frequencies up to 96kHz. The 64x setting must be used for sampling frequencies greater than 96kHz. ® 17 PCM1737 B15 REGISTER 19 R/W B14 IDX6 B13 IDX5 B12 IDX4 B11 IDX3 B10 IDX2 B9 IDX1 B8 IDX0 B7 res B6 DMF1 B5 DMF0 B4 DM12 B3 res B2 res B1 B0 DAC2 DAC1 R/W Read/Write Mode Select When R/W = 0, a Write operation is performed. When R/W = 1, a Read operation is performed. Default Value: 0 DACx DAC Operation Control Where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) or VOUTR (x = 2). These bits are Read/Write. Default Value: 0 DACx = 0 DACx = 1 DAC Operation Enabled (default) DAC Operation Disabled The DAC operation controls are used to enable and disable the DAC outputs, V OUTL and VOUTR. When DACx = 0, the corresponding output will generate the audio waveform dictated by the data present on the DATA pin. When DACx = 1, the corresponding output will be set to the bipolar zero level, or V CC/2. DM12 Digital De-Emphasis Function Control This bit is Read/Write. Default Value: 0 DM12 = 0 DM12 = 1 De-Emphasis Disabled (default) De-Emphasis Enabled The DM12 bit is used to enable or disable the digital de-emphasis function. Refer to the plots shown in the Typical Performance Curves section of this data sheet. DMF[1:0] Sampling Frequency Selection for the De-Emphasis Function These bits are Read/Write. Default Value: 00B The DMF[1:0] bits are used to select the sampling frequency used for the digital de-emphasis function when it is enabled. DMF[1:0] 00 01 10 11 De-Emphasis Same Rate Selection 44.1kHz (default) 48kHz 32kHz Reserved ® PCM1737 18 B15 REGISTER 20 R/W B14 IDX6 B13 IDX5 B12 IDX4 B11 IDX3 B10 IDX2 B9 IDX1 B8 IDX0 B7 X4DS B6 FLT1 B5 FLT0 B4 CLKD B3 CLKE B2 FMT2 B1 FMT1 B0 FMT0 R/W Read/Write Mode Select When R/W = 0, a Write operation is performed. When R/W = 1, a Read operation is performed. Default Value: 0 Audio Interface Data Format These bits are Read/Write. Default Value: 000B The FMT[2:0] bits are used to select the data format for the serial audio interface. The table below shows the available format options. FMT[2:0] 000 001 010 011 100 101 110 111 Audio Data Format Selection 24-Bit Standard Format, Right-Justified Data (default) 20-Bit Standard Format, Right -Justified Data 18-Bit Standard Format, Right-Justified Data 16-Bit Standard Format, Right-Justified Data I2S Format, 16 to 24 Bits Right-Justified Format, 16 to 24 Bits Reserved Reserved FMT[2:0] CLKE CLKO Output Enable This bit is Read/Write. Default Value: 0 CLKE = 0 CLKE = 1 CLKO Enabled (default) CLKO Disabled The CLKE bit is used to enable or disable the system clock output pin, CLKO. When CLKO is enabled, it will output either a full or half rate clock, based upon the setting of the CLKD bit. When CLKO is disabled, it is set to a high impedance state. CLKD CLKO Frequency Selection This bit is Read/Write. Default Value: 0 CKLD = 0 CKLD = 1 Full Rate, fCLKO = fSCLK (default) Half Rate, fCLKO = fSCLK/2 The CLKD bit is used to select the clock frequency for the CLKO pin. ® 19 PCM1737 REGISTER 20 (cont.) FLT[1:0] Digital Filter Roll-Off Control These bits are Read/Write. Default Value: 00B FLT[1:0] = 00B FLT[1:0] = 01B FLT[1:0] = 10B Sharp Roll-Off (default) Slow Roll-Off 1 Slow Roll-Off 2 Bits FLT[1:0] allow the user to select the digital filter roll-off that is best suited to their application. Three filter roll-off selections are available: Sharp, Slow 1, and Slow 2 The filter responses for these selections are shown in the Typical Performance Curves section of this data sheet. Slow roll-off performance is specified for 8x interpolation (X4DS = 0) only. X4DS 4x/8x Digital Interpolation Control This bit is Read/Write. Default Value: 0 X4DS = 0 X4DS = 1 8x Interpolation (default) 4x Interpolation, used for fS = 192kHz or 176.4kHz Bit X4DS allows the user to select the oversampling rate of the digital interpolation filter. For sampling frequencies up to 96kHz, 8x interpolation is used, while 4x interpolation is used for sampling frequencies, greater than 96kHz. ® PCM1737 20 B15 REGISTER 21 R/W B14 IDX6 B13 IDX5 B12 IDX4 B11 IDX3 B10 IDX2 B9 IDX1 B8 IDX0 B7 INC B6 REG6 B5 REG5 B4 REG4 B3 REG3 B2 REG2 B1 REG1 B0 REG0 R/W Read/Write Mode Select When R/W = 0, a Write operation is performed. When R/W = 1, a Read operation is performed. Default Value: 0 INC Auto-Increment Read Control This bit is Read/Write. Default Value: 0 INC = 0 INC = 1 Auto-Increment Read Disabled (default) Auto-Increment Read Enabled The INC bit is used to enable or disable the Auto-Increment Read feature of the Serial Control Interface. Refer to the Serial Control Interface section of this data sheet for details regarding Auto-Increment Read operation. REG[6:0] Read Register Index These bits are Read/Write. Default Value: 01H Bits REG[6:0] are used to set the index of the register to be read when performing a Single Register Read operation. In the case of an Auto-Increment Read operation, bits REG[6:0] indicate the index of the last register to be read in the in the Auto-Increment Read sequence. For example, if Registers 1 through 6 are to be read during an Auto-Increment Read operation, bits REG[6:0] would be set to 06H. Refer to the Serial Control Interface section of this data sheet for details regarding the Single Register and AutoIncrement Read operations. ® 21 PCM1737 ANALOG OUTPUTS The PCM1737 includes two independent output channels: VOUTL and VOUTR. These are unbalanced outputs, each capable of driving 3.1Vp-p typical into a 5kΩ AC-coupled load (VCC = +5V). The internal output amplifiers for VOUTL and VOUTR are DC biased to a DC common-mode (or bipolar zero) voltage, equal to VCC/2. The output amplifiers include an RC continuous-time filter, which helps to reduce the out-of-band noise energy present at the DAC outputs due to the noise shaping characteristics of the PCM1737’s delta-sigma D/A converters. The frequency response of this filter is shown in Figure 11. By itself, this filter is not enough to attenuate the out-of-band noise to an acceptable level for most applications. An external low-pass filter is required to provide sufficient outof-band noise rejection. Further discussion of DAC postfilter circuits is provided in the Applications Information section of this data sheet. VCOML AND VCOMR OUTPUTS Two unbuffered common-mode voltage output pins, VCOML (pin 17) and VCOMR (pin 12), are brought out for decoupling purposes. These pins are nominally biased to a DC voltage level equal to VCC/2. These pins may be used to bias external circuits, a voltage follower is required for buffering purposes. Figure 12 shows an example of using the VCOML and VCOMR pins for external biasing applications. ZERO FLAG AND INFINITE ZERO DETECT MUTE FUNCTIONS The PCM1737 includes circuitry for detecting an all ‘0’ data condition for the data input pin, DATA. This includes two independent functions: Zero Output Flags and Zero Detect Mute. Although the flag and mute functions are independent of one another, the zero detection mechanism is common to both functions. Zero Detect Condition Zero Detection for each output channel is independent from the other. If the data for a given channel remains at a ‘0’ level for 1024 sample periods (or LRCK clock periods), a Zero Detect condition exists for that channel. Zero Output Flags Given that a Zero Detect condition exists for one or more channels, the Zero flag pins for those channels will be set to a logic ‘1’state. There are Zero Flag pins for each channel, ZEROL (pin 23) and ZEROR (pin 24). These pins can be used to operate external mute circuits, or used as status indicators for a microcontroller, audio signal processor, or other digitally-controlled functions. Infinite Zero Detect Mute Infinite Zero Detect Mute is an internal logic function. The Zero Detect Mute can be enabled or disabled using the INZD bit of Control Register 18. The reset default is Zero Detect Mute disabled, INZD = 0. Given that a Zero Detect Condition exists for one or more channels, the zero mute circuitry will immediately force the corresponding DAC output(s) to the bipolar zero level, or VCC/2. ANALOG FILTER RESPONSE 10 0 –10 Level (dB) –20 –30 –40 –50 –60 100 1k 10k 100k 1M 10M Frequency (Hz) FIGURE 11. Output Filter Frequency Response. ® PCM1737 22 PCM1737 VOUTx R2 10µF + R1 C2 R3 C1 2 AV = –1, where AV = – VCC 1/2 OPA2353 1 R2 R1 3 Filtered Output VCOMx + x = L or R 10µF (a) Using VCOM to Bias a Single-Supply Filter Stage PCM1737 VCC OPA337 VCOMx + 10µF Buffered VCOM x = L or R (b) Using a Voltage Follower to Buffer VCOM when Biasing Multiple Nodes V+ VCC 49.9kΩ 1% –IN 25kΩ 25kΩ OUT +IN + 10µF INA134 x = L or R V– (c) Using an INA134 for DC-Coupled Output 25kΩ 25kΩ To Low-Pass Filter Stage SENSE PCM1737 VOUTx VCOMx REF FIGURE 12. Biasing External Circuits Using the VCOM1 and VCOM2 Pins. ® 23 PCM1737 NOTE: (1) RS = 20Ω to 100Ω RS(1) LRCK DATA PCM1737 ML MC MDI MDO ZEROR ZEROL RSTB NC NC VCCL GNDL VCOML VOUTL VCCA + C8 C7 + C5 To Output Filter Circuits Analog Ground + C9 x x + C10 Zero Flag Outputs From Host or Master Reset To/From Host Controller From/To Audio Source BCLK CLKO SCLK C1 C2 VSS VDD TEST1 TEST2 + VCCR C3 GNDR + C4 VCOMR VOUTR GNDA + +3.3V Regulator C6 + +5V Analog C1, C4, C6, C9 = 10µF Tantalum or Aluminum Electrolytic C2, C5 = 0.1µF Ceramic C3, C10 = 1µF Tantalum or Aluminum Electrolytic C7, C8 = 1-10µF Aluminum Electrolytic FIGURE 13. Basic Connection Diagram. APPLICATIONS INFORMATION CONNECTION DIAGRAMS A basic connection diagram is shown in Figure 13, with the necessary power supply bypassing and decoupling components. Burr-Brown recommends using the component values shown in Figure 13 for all designs. The use of series resistors (22Ω to 100Ω) are recommended for SCLK, LRCK, BCLK, DATA inputs. The series resistor combines with the stray PCB and device input capacitance to form a low-pass filter which reduces high frequency noise emissions and helps to dampen glitches and ringing present on clock and data lines. POWER SUPPLIES AND GROUNDING The PCM1737 requires a +5V analog supply and a +3.3V digital supply. The +5V supply is used to power the DAC analog and output filter circuitry, while the +3.3V supply is used to power the digital filter and serial interface circuitry. For best performance, the +3.3V supply should be derived from the +5V supply using a linear regulator, as shown in Figure 13. Burr-Brown’s REG1117-3.3 is an ideal choice for this application. Proper power supply bypassing is shown in Figure 13. The bypass capacitors should be tantalum or aluminum electrolytic, while the 0.1µF capacitors are ceramic (X7R type is recommended for surface-mount applications). ® D/A OUTPUT FILTER CIRCUITS Delta-sigma D/A converters utilize noise-shaping techniques to improve in-band Signal-to-Noise Ratio (SNR) performance at the expense of generating increased out-of-band noise above the Nyquist Frequency, or fS/2. The out-ofband noise must be low-pass filtered in order to provide the optimal converter performance. This is accomplished by a combination of on-chip and external low-pass filtering. Figures 12a and 14 show the recommended external lowpass active filter circuits for dual and single-supply applications. These circuits are 2nd-order Butterworth filters using the Multiple Feedback (MFB) circuit arrangement, which reduces sensitivity to passive component variations over frequency and temperature. For more information regarding MFB active filter design, please refer to Burr-Brown Applications Bulletin AB-034. R2 R1 VIN C2 R3 C1 2 1 3 OPA2134 AV ≈ – R2 R1 R4 VOUT FIGURE 14. Dual-Supply Filter Circuit. 24 PCM1737 Since the overall system performance is defined by the quality of the D/A converters and their associated analog output circuitry, high quality audio op amps are recommended for the active filters. Burr-Brown’s OPA2134 and OPA2353 dual op amps are shown in Figures 12a and 14, and are recommended for use with the PCM1737. plane split/cut to allow for short, direct connections to the digital audio interface and control signals originating from the digital section of the board. Separate power supplies are recommended for the digital and analog sections of the board. This prevents the switching noise present on the digital supply from contaminating the analog power supply and degrading the dynamic performance of the PCM1737. In cases where a common +5V supply must be used for the analog and digital sections, an inductance (RF choke, ferrite bead) should be placed between the analog and digital +5V supply connections to avoid coupling of the digital switching noise into the analog circuitry. Figure 16 shows the recommended approach for single-supply applications. PCB LAYOUT GUIDELINES A typical PCB floor plan for the PCM1600 and PCM1601 is shown in Figure 15. A ground plane is recommended, with the analog and digital sections being isolated from one another using a split or cut in the circuit board. The PCM1737 should be oriented with the digital I/O pins facing the ground Digital Power +VD DGND Analog Power AGND +5VA +VS –VS REG VCC Digital Logic and Audio Processor VDD DGND PCM1737 Output Circuits Digital Ground AGND DIGITAL SECTION ANALOG SECTION Analog Ground Return Path for Digital Signals FIGURE 15. Recommended PCB Layout. Power Supplies RF Choke or Ferrite Bead +5V AGND +VS –VS REG VDD VDD VCC DGND PCM1737 AGND Output Circuits Common Ground DIGITAL SECTION ANALOG SECTION FIGURE 16. Single-Supply PCB Layout. ® 25 PCM1737 – + 4fS or 8fS + Z–1 + Z–1 + Z–1 + Z–1 + 8-Level Quantizer 64fS or 128fS FIGURE 17. Eight-Level Delta-Sigma Modulator. 64x Oversampling 0 –20 –40 Amplitude (dB) –60 –80 –100 –120 –140 –160 –180 0 1 2 3 4 5 6 7 8 Frequency (fS) Amplitude (dB) 0 –20 –40 –60 –80 –100 –120 –140 –160 –180 0 1 2 3 4 5 6 7 8 Frequency (fS) 128x Oversampling FIGURE 18. Quantization Noise Spectrum (64x/128x oversampling). CLOCK JITTER 125 120 Dynamic Range (dB) 115 110 105 100 95 90 0 100 200 300 Jitter (ps) 400 500 600 The combined oversampling rate of the delta-sigma modulator and the interpolation filter is 64fS or 128fS. The theoretical quantization noise performance of the 8-level delta-sigma modulator is shown in Figure 18. The enhanced multi-level delta-sigma architecture also has advantages for input clock jitter sensitivity due to the multilevel quantizer, with the simulated jitter sensitivity shown in Figure 19. KEY PERFORMANCE PARAMETERS AND MEASUREMENT This section provides information on how to measure key dynamic performance parameters for the PCM1737. In all cases, an Audio Precision System Two Cascade or equivalent audio measurement system is utilized to perform the testing. TOTAL HARMONIC DISTORTION + NOISE Total Harmonic Distortion + Noise (THD+N) is a significant figure of merit for audio D/A converters since it takes into account both harmonic distortion and all noise sources within a specified measurement bandwidth. The true rms value of the distortion and noise is referred to as THD+N. For the PCM1737, THD+N is measured with a full scale, 1kHz digital sine wave as the test stimulus at the input of the 26 FIGURE 19. Jitter Sensitivity. THEORY OF OPERATION The delta-sigma section of PCM1737 is based on a 8-level amplitude quantizer and a 4th-order noise shaper. This section converts the oversampled input data to 8-level delta-sigma format. A block diagram of the 8-level delta-sigma modulator is shown in Figure 17. This 8-level delta-sigma modulator has the advantage of stability and clock jitter sensitivity over the typical one-bit (2-level) delta-sigma modulator. ® PCM1737 DAC. The digital generator is set to 24-bit audio word length and a sampling frequency of 44.1kHz, 96kHz, or 192kHz. The digital generator output is taken from the unbalanced S/PDIF connector of the measurement system. The S/PDIF data is transmitted via a coaxial cable to the digital audio receiver on the DEM-DAI1737 demo board. The receiver is then configured to output 24-bit data in either I2S or left-justified data format. The DAC audio interface format is programmed to match the receiver output format. The analog output is then taken from the DAC post filter and connected to the analog analyzer input of the measurment system. The analog input is band limited using filters resident in the analyzer. The resulting THD+N is measured by the analyzer and displayed by the measurement system. DYNAMIC RANGE Dynamic range is specified as A-Weighted, THD+N measured with a –60dBFS, 1kHz digital sine wave stimulus at the input of the D/A converter. This measurement is designed to give a good indicator of how the DAC will perform given a low-level input signal. The measurement setup for the dynamic range measurement is shown in Figure 21, and is similar to the THD+N test setup discussed previously. The differences include the bandlimit filter selection, the additional A-Weighting filter, and the –60dBFS input level. IDLE CHANNEL SIGNAL-TO-NOISE RATIO The SNR test provides a measure of the noise floor of the D/A converter. The input to the D/A is all 0’s data, and the D/A converter’s Infinite Zero Detect Mute function must be disabled (default condition at power up for the PCM1737). This ensures that the delta-sigma modulator output is connected to the output amplifier circuit so that idle tones (if present) can be observed and effect the SNR measurement. The dither function of the digital generator must also be disabled to ensure an all ‘0’s data stream at the input of the D/A converter. The measurement setup for SNR is identical to that used for dynamic range, with the exception of the input signal level. (see the notes provided in Figure 21). Evaluation Board DEM-DAI1737 S/PDIF Receiver 2nd-Order Low-Pass Filter f–3dB = 54kHz or 108kHz PCM1737 S/PDIF Output Digital Generator 0dBFS, 1kHz Sine Wave Analyzer and Display RMS Mode 20kHz Apogee Filter Band Limit HPF = 22Hz LPF = 30kHz Notch Filter fC = 1kHz FIGURE 20. Test Setup for THD+N Measurement. Evaluation Board DEM-DAI1737 S/PDIF Receiver 2nd-Order Low-Pass Filter f–3dB = 54kHz or 108kHz PCM1737(1) S/PDIF Output Digital Generator 0% Full Scale, Dither Off (SNR) or –60dBFS, 1kHz Sine Wave (Dynamic Range) Analyzer and Display RMS Mode A-Weight Filter(2) Band Limit HPF = 22Hz LPF = 22kHz Notch Filter fC = 1kHz NOTES: (1) Infinite Zero Detect Mute disabled. (2) Results without A-Weighting will be approximately 3dB worse. FIGURE 21. Test Set-Up for Dynamic Range and SNR Measurements. ® 27 PCM1737