PCM1744U

® PCM1744 PCM 1744 For most current data sheet and other product information, visit www.burr-brown.com 24 Bits, 96kHz, Sampling Stereo Audio DIGITAL-TO-ANALOG CONVERTER TM FEATURES DESCRIPTION ● COMPLETE STEREO DAC: Includes Digital Filter and Output Amp The PCM1744 is a complete low cost stereo audio digital-to-analog converter (DAC), operating off of a 256fS or 384fS system clock. The DAC contains a 3rdorder ∆Σ modulator, a digital interpolation filter, and an analog output amplifier. The PCM1744 accepts 24-bit input data in a I2S format. ● DYNAMIC RANGE: 95dB ● MULTIPLE SAMPLING FREQUENCIES: Up to 96kHz ● 8x OVERSAMPLING DIGITAL FILTER ● SYSTEM CLOCK: 256fS / 384fS ● 24-BIT I2S DATA INPUT FORMAT ● SMALL 14-PIN SOIC PACKAGE The digital filter performs an 8x interpolation function and includes de-emphasis at 44.1kHz. The PCM1744 can accept digital audio sampling frequencies from 16kHz to 96kHz, always at 8X oversampling. The PCM1744 is ideal for low-cost, CD-quality consumer audio applications. Multi-level Delta-Sigma Modulator BCKIN LRCIN DIN Serial Input I/F Low-pass Filter 8X Oversampling Digital Filter VOUTL CAP Multi-level Delta-Sigma Modulator FORMAT DAC DAC Low-pass Filter VOUTR Mode Control I/F DM Power Supply 256fS/384fS VCC SCKI GND International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® © 1999 Burr-Brown Corporation SBAS130 PDS-1553A 1 PCM1744 Printed in U.S.A. September, 1999 SPECIFICATIONS All specifications at +25°C, +VCC = +5V, fS = 44.1kHz, and 18-bit input data, SYSCLK = 384fS, unless otherwise noted. PCM1744 PARAMETER CONDITIONS RESOLUTION DATA FORMAT Audio Data Interface Format Audio Data Format Sampling Frequency (fS) Internal System Clock Frequency THD+N at FS (0dB) THD+N at –60dB Dynamic Range Signal-to-Noise Ratio Channel Separation DC ACCURACY Gain Error Gain Mismatch, Channel-to-Channel Bipolar Zero Error ANALOG OUTPUT Output Voltage Center Voltage Load Impedance MAX UNITS Bits I2S Two’s Binary Complement 16 96 kHz 0.8 ±0.8 VDC VDC µA 256fS /384fS TTL 2.0 f = 991kHz EIAJ, A-weighted EIAJ, A-weighted 90 90 88 VOUT = VCC/2 at BPZ Full Scale (0dB) AC Load –83 –32 95 97 95 –79 dB dB dB dB dB ±1.0 ±1.0 ±20 ±10.0 ±5.0 ±50 % of FSR % of FSR mV 0.62 x VCC VCC/2 Vp-p VDC kΩ 10 DIGITAL FILTER PERFORMANCE Passband Stopband Passband Ripple Stopband Attenuation Delay Time INTERNAL ANALOG FILTER –3dB Bandwidth Passband Response TYP 24 DIGITAL INPUT/OUTPUT Logic Level Input Logic Level VIH(1) VIL(1) Input Logic Current: IIN(1) DYNAMIC PERFORMANCE(2) MIN 0.445 11.125/fS fS fS dB dB sec 100 –0.16 kHz dB 0.555 ±0.17 –35 f = 20kHz POWER SUPPLY REQUIREMENTS Voltage Range Supply Current Power Dissipation 4.5 TEMPERATURE RANGE Operation Storage –25 –55 5 13 65 5.5 18 90 VDC mA mW +85 +125 °C °C NOTES: (1) Pins 1, 2, 3, 12, 13, 14: LRCIN, DIN, BCKIN, DM, FORMAT, SCKI. (2) Dynamic performance specs are tested with 20kHz low pass filter and THD+N specs are tested with 30kHz LPF, 400Hz HPF, Average-Mode. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® PCM1744 2 PIN ASSIGNMENTS PIN CONFIGURATION TOP VIEW SOIC PIN NAME I/O FUNCTION 1(1) LRCIN IN Sample Rate Clock Input 2(1) DIN IN Audio Data Input 3(1) BCKIN IN Bit Clock Input for Audio Data. NC — No Connection Common Pin of Analog Output Amp 4 LRCIN DIN 1 14 2 13 SCKI 5 CAP — 6 VOUTR OUT 7 GND — Ground Power Supply TEST BCKIN 3 12 DM 8 VCC — NC 4 11 NC 9 VOUTL OUT CAP 5 10 NC 10 NC — VOUTR 6 9 VOUTL GND 7 PCM1744 8 Right-Channel Analog Output Left-Channel Analog Output No Connection 11 NC — No Connection 12(2) DM IN De-Emphasis Control HIGH: De-emphasis ON LOW: De-emphasis OFF 13(2) TEST — Test Pin. Must be left open. 14(1) SCKI IN System Clock Input (256fS or 384fS) VCC NOTE: (1) Schmitt-Trigger input. (2) Schmitt-Trigger input with internal pull-up. ELECTROSTATIC DISCHARGE SENSITIVITY ABSOLUTE MAXIMUM RATINGS Power Supply Voltage ...................................................................... +6.5V +VCC to +VDD Difference ................................................................... ±0.1V Input Logic Voltage .................................................. –0.3V to (VDD + 0.3V) Power Dissipation .......................................................................... 290mW Operating Temperature Range ......................................... –25°C to +85°C Storage Temperature ...................................................... –55°C to +125°C Lead Temperature (soldering, 5s) .................................................. +260°C Thermal Resistance, θJA .............................................................. +90°C/W This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) PCM1744 " SO-14 " 235 " SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(2) TRANSPORT MEDIA –25°C to +85°C " PCM1744U PCM1744U PCM1744U PCM1744U/2K Rails Tape and Reel NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book, or visit the Burr-Brown web site at www.burr-brown.com. (2) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K indicates 2000 devices per reel). Ordering 2000 pieces of “PCM1744U/2K” will get a single 2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book. ® 3 PCM1744 TYPICAL PERFORMANCE CURVES At TA = +25°C, +VCC = +5V, fS = 44.1kHz, SYSCLK = 256fS, unless otherwise noted. DYNAMIC PERFORMANCE 0.008 3.1 2.8 0.005 2.7 –60dB 0.003 2.6 0.002 2.5 0.001 2.4 SNR (dB) 2.9 THD+N at –60dB (%) 3.0 0.006 99 97 97 96 96 95 95 94 2.3 0 25 50 75 85 93 –25 100 93 0 Temperature (°C) THD+N vs POWER SUPPLY THD+N at 0dB (%) 3.0 0dB 0.006 2.9 0.005 2.8 0.004 2.7 0.003 2.6 0.002 2.5 –60dB 0.001 0 2.3 5.25 97 97 96 96 95 95 Dynamic Range 93 4.5 4.75 5.0 98 5.2 98 97 0.012 4.2 3.7 0dB 0.008 3.2 0.006 2.7 –60dB 0.004 97 SNR 96 96 95 95 94 94 93 93 Dynamic Range 92 91 90 90 89 89 88 44.1 96 48 88.2 Sampling Rate (kHz) Sampling Rate (kHz) ® 4 92 91 88 2.2 88.2 SNR (dB) 4.7 THD+N AT –60dB (%) 0.014 THD+N at 0dB (%) 5.5 SNR, DYNAMIC RANGE vs SAMPLING RATE THD+N vs SAMPLING RATE PCM1744 5.25 VCC (V) 0.016 48 94 93 5.5 VCC (V) 44.1 100 98 SNR 94 2.4 0.01 85 99 98 SNR (dB) 3.1 5.0 75 99 THD+N at –60dB (%) 0.008 4.75 50 SNR, DYNAMIC RANGE vs POWER SUPPLY 3.2 4.5 25 Temperature (°C) 0.009 0.007 94 Dynamic Range Dynamic Range (dB) 0 –25 98 SNR 96 Dynamic Range (dB) 0.004 99 98 0dB 0.007 THD+N at 0dB (%) SNR, DYNAMIC RANGE vs TEMPERATURE 3.2 Dynamic Range (dB) THD+N vs TEMPERATURE 0.009 TYPICAL PERFORMANCE CURVES At TA = +25°C, +VCC = +VDD = +5V, fS = 44.1kHz, and 18-bit input data, SYSCLK = 384fS, unless otherwise noted. DIGITAL FILTER OVERALL FREQUENCY CHARACTERISTIC PASSBAND RIPPLE CHARACTERISTIC 0 –20 –0.2 –40 –0.4 dB dB 0 –60 –0.6 –80 –0.8 –100 0 0.4536fS 1.3605fS 2.2675fS 3.1745fS –1 4.0815fS 0 0.1134fS Frequency (Hz) DE-EMPHASIS FREQUENCY RESPONSE (44.1kHz) 0.3402fS 0.4535fS DE-EMPHASIS FREQUENCY ERROR (44.1kHz) 0 0.6 –2 0.4 –4 0.2 Error (dB) Level (dB) 0.2268fS Frequency (Hz) –6 0.0 –8 –0.2 –10 –0.4 –12 –0.6 0 5 10 15 20 25 0 Frequency (kHz) 4999.8375 9999.675 14999.5125 19999.35 Frequency (kHz) ® 5 PCM1744 1/fS L_ch LRCIN (pin 1) R_ch BCKIN (pin 3) AUDIO DATA WORD = 24-BIT DIN (pin 2) 1 2 3 20 21 22 23 24 MSB 1 LSB 2 3 MSB 1 20 21 22 23 24 2 LSB FIGURE 1. I2S Data Input Timing. LRCKIN 1.4V tBCH tBCL tLB BCKIN 1.4V tBL tBCY 1.4V DIN tDS tDH BCKIN Pulse Cycle Time : tBCY : 100ns (min) BCKIN Pulse Width High : tBCH : 50ns (min) BCKIN Pulse Width Low : tBCL : 50ns (min) BCKIN Rising Edge to LRCIN Edge : tBL : 30ns (min) LRCIN Edge to BCKIN Rising Edge : tLB : 30ns (min) DIN Set-up Time : tDS : 30ns (min) DIN Hold Time : tDH : 30ns (min) FIGURE 2. Audio Data Input Timing. SYSTEM CLOCK The system clock for PCM1744 must be either 256fS or 384fS, where fS is the audio sampling frequency (LRCIN), typically 32kHz, 44.1kHz, 48kHz, 88.2kHz or 96kHz. The system clock is used to operate the digital filter and the noise shaper. The system clock input (SCKI) is at pin 14. Timing conditions for SCKI are shown in Figure 3. tSCKIH 2.0V SCKI 0.8V tSCKIL System Clock Pulse Width High System Clock Pulse Width Low tSCKIH tSCKIL PCM1744 has a system clock detection circuit which automatically detects the frequency, either 256fS or 384fS. The system clock should be synchronized with LRCIN (pin 1), but PCM1744 can compensate for phase differences. If the phase difference between LRCIN and system clock is greater 13ns (min) 13ns (min) FIGURE 3. System Clock Timing Requirements. ® PCM1744 6 than ±6 bit clocks (BCKIN), the synchronization is performed automatically. The analog outputs are forced to a bipolar zero state (VCC/2) during the synchronization function. Table I shows the typical system clock frequency inputs for the PCM1744. RESET PCM1744 has an internal power-on reset circuit. The internal power-on reset initializes (resets) when the supply voltage VCC > 2.2V (typ). The power-on reset has an initialization period equal to 1024 system clock periods after VCC > 2.2V. During the initialization period, the outputs of the DAC are invalid, and the analog outputs are forced to VCC/2. Figure 5 illustrates the power-on reset and reset-pin reset timing. SYSTEM CLOCK FREQUENCY (MHz) SAMPLING RATE (LRCIN) 32kHz 44.1kHz 48kHz 88.2kHz 96kHz 256fS 384fS 8.192 11.2896 12.288 22.5792 24.576 12.288 16.9340 18.432 33.868 36.864 DE-EMPHASIS CONTROL Pin 12 (DM) enables PCM1744’s de-emphasis function. Deemphasis operates only at 44.1kHz. TABLE I. System Clock Frequencies vs Sampling Rate. DM 0 1 TYPICAL CONNECTION DIAGRAM Figure 4 illustrates the typical connection diagram for PCM1744 used in a stand-alone application. De-emphasis OFF De-emphasis ON (44.1kHz) TABLE II. De-emphasis Control Selection. INPUT DATA FORMAT PCM1744 can accept input data a 24-bit I2S format, as shown in Figure 1. 10µF +5V Analog + 2 3 PCM Audio Data Processor 1 7 8 GND VCC DIN VOUTL BCKIN CAP 9 5 + LRCIN PCM1744 VOUTR Post LPF Lch Analog Out Post LPF Rch Analog Out 10µF 6 13 14 SCKI 256fS or 384fS System Clock TEST DM 12 De-Emphasis Control FIGURE 4. Typical Connection Diagram. VCC 2.6V 2.2V 1.8V Reset Reset Removal Internal Reset 1024 system (= SCKI) clocks SCKI Clock FIGURE 5. Internal Power-On Reset Timing. ® 7 PCM1744 APPLICATION CONSIDERATIONS INTERNAL ANALOG FILTER FREQUENCY RESPONSE (20Hz~24kHz, Expanded Scale) DELAY TIME 1.0 There is a finite delay time in delta-sigma converters. In A/D converters, this is commonly referred to as latency. For a delta-sigma D/A converter, delay time is determined by the order number of the FIR filter stage, and the chosen sampling rate. The following equation expresses the delay time of PCM1744: dB 0.5 0 TD = 11.125 x 1/fS –0.5 For fS = 44.1kHz, TD = 11.125/44.1kHz = 251.4µs Applications using data from a disc or tape source, such as CD audio, CD-Interactive, Video CD, DAT, Minidisc, etc., generally are not affected by delay time. For some professional applications such as broadcast audio for studios, it is important for total delay time to be less than 2ms. –1.0 20 100 1k Frequency (Hz) 10k 24k FIGURE 6. Low-Pass Filter Frequency Response. OUTPUT FILTERING For testing purposes all dynamic tests are done on the PCM1744 using a 20kHz low-pass filter. This filter limits the measured bandwidth for THD+N, etc. to 20kHz. Failure to use such a filter will result in higher THD+N and lower SNR and dynamic range readings than are found in the specifications. The low-pass filter removes out-of-band noise. Although it is not audible, it may affect dynamic specification numbers. dB INTERNAL ANALOG FILTER FREQUENCY RESPONSE (10Hz~10MHz) 10 5 0 –5 –10 –15 –20 –25 –30 –35 –40 –45 –50 –55 –60 10 100 1k 10k 100k 1M The performance of the internal low pass filter from DC to 24kHz is shown in Figure 6. The higher frequency roll-off of the filter is shown in Figure 7. If the user’s application has the PCM1744 driving a wideband amplifier, it is recommended to use an external low-pass filter. A simple 3rdorder filter is shown in Figure 8. For some applications, a passive RC filter or 2nd-order filter may be adequate. 10M Frequency (Hz) BYPASSING POWER SUPPLIES The power supplies should be bypassed as close as possible to the unit. It is also recommended to include a 0.1µF ceramic capacitor in parallel with the 10µF tantalum bypass capacitor. FIGURE 7. Low-Pass Filter Wideband Frequency Response. GAIN vs FREQUENCY 6 90 + 10kΩ VSIN 10kΩ 680pF OPA134 10kΩ 0 –34 –90 –54 –180 Phase 100pF – –74 –270 –94 –360 100 FIGURE 8. 3rd-Order LPF. ® PCM1744 8 1k 10k Frequency (Hz) 100k 1M Phase (°) 1500pF Gain (dB) Gain –14 + In + 8fS 24-Bit + Z–1 + + – + Z–1 Z–1 – + + 5-level Quantizer + 4 3 Out 48fS (384fS) 64fS (256fS) 2 1 0 FIGURE 9. 5-Level ∆Σ Modulator Block Diagram. THEORY OF OPERATION 5-LEVEL DELTA SIGMA MODULATOR The delta-sigma section of PCM1744 is based on a 5-level amplitude quantizer and a 3rd-order noise shaper. This section converts the oversampled input data to 5-level deltasigma format. A block diagram of the 5-level delta-sigma modulator is shown in Figure 9. This 5-level delta-sigma modulator has the advantage of stability and clock jitter over the typical one-bit (2-level) delta-sigma modulator. The combined oversampling rate of the delta-sigma modulator and the internal 8x interpolation filter is 96fS for a 384fS system clock, and 64fS for a 256fS system clock. The theoretical quantization noise performance of the 5-level delta-sigma modulator is shown in Figure 10. 20 0 Gain (–dB) –20 –40 –60 –80 –100 –120 –140 –160 0 5 10 15 20 25 Frequency (kHz) FIGURE 10. Quantization Noise Spectrum. ® 9 PCM1744 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) PCM1744U ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM PCM1744U (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of