Burr Brown Products from Texas Instruments
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
16/20-BIT SINGLE-ENDED ANALOG INPUT/OUTPUT STEREO AUDIO CODECS
FEATURES
• • • • • Monolithic 20-Bit ∆Σ ADC and DAC 16/20-Bit Input/Output Data Software Control: PCM3002 Hardware Control: PCM3003 Stereo ADC: – Single-Ended Voltage Input – Antialiasing Filter – 64× Oversampling – High Performance • THD+N: –86 dB • SNR: 90 dB • Dynamic Range: 90 dB Stereo DAC: – Single-Ended Voltage Output – Analog Low-Pass Filter – 64× Oversampling – High Performance • THD+N: –86 dB • SNR: 94 dB • Dynamic Range: 94 dB Special Features (PCM3002, PCM3003) – Digital De-Emphasis: 32 kHz, 44.1 kHz, 48 kHz – Power Down: ADC/DAC Independent Special Features (PCM3002) – Digital Attenuation (256 Steps) – Soft Mute – Digital Loopback – Four Alternative Audio Data Formats Sampling Rate: 4 kHz to 48 kHz • • • • • Single 3-V Power Supply Small Package: SSOP-24
APPLICATIONS
DVC Applications DSC Applications Portable/Mobile Audio Applications
DESCRIPTION
The PCM3002 and PCM3003 are low-cost, single-chip stereo audio codecs (analog-to-digital and digital-to-analog converters) with single-ended analog voltage input and output. The ADCs and DACs employ delta-sigma modulation with 64-times oversampling. The ADCs include a digital decimation filter, and the DACs include an 8-times oversampling digital interpolation filter. The DACs also include digital attenuation, de-emphasis, infinite zero detection, and soft mute to form a complete subsystem. The PCM3002 and PCM3003 operate with left-justified (ADC) and right-justified (DAC) formats, while the PCM3002 also supports other formats, including the I2S data format. The PCM3002 and PCM3003 provide a power-down mode that operates on the ADCs and DACs independently. The PCM3002 and PCM3003 are fabricated using a highly advanced CMOS process, and are available in a 24-pin SSOP package. The PCM3002 and PCM3003 are suitable for a wide variety of cost-sensitive consumer applications where good performance is required. The PCM3002 programmable functions are controlled by software. The PCM3003 functions, which are controlled by hardware, include de-emphasis, power-down, and audio data format selections.
•
•
•
•
Lch In Analog Front-End Rch In
Delta-Sigma Modulator
Digital Decimation Filter *
Digital Out Serial Interface and Mode Control Digital In
Lch Out Rch Out
Low-Pass Filter and Output Buffer * PCM3002 Only
Multilevel Delta-Sigma Modulator
Digital Interpolation Filter
Mode Control System Clock
B0006-01
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. System Two, Audio Precision are trademarks of Audio Precision, Inc. All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright © 2000–2004, Texas Instruments Incorporated
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ELECTRICAL CHARACTERISTICS
All specifications at TA = 25°C, VDD = VCC = 3 V, fS = 44.1 kHz, SYSCLK = 384 fS, and 16-bit data, unless otherwise noted
PARAMETER DIGITAL INPUT/OUTPUT Input Logic VIH (1) (2) (3) VIL (1) (2) (3) IIN (2) IIN (1) (3) VOH (4) VOL
(4)
CONDITIONS
PCM3002E/3003E MIN TYP MAX UNITS
Input logic level Input logic current
0.7 VDD 0.3 VDD ±1 100 IOUT = –1 mA VDD – 0.3 0.3 0.3 4 (6) 256 fS 1.024 1.536 2.048 384 fS 512 fS 44.1 11.2896 16.9344 22.5792 20 48 12.288 18.432 24.576
VDC µA
Output Logic Output logic level IOUT = 1 mA IOUT = 1 mA Sampling frequency System clock frequency ADC CHARACTERISTICS Resolution DC Accuracy Gain mismatch, channelto-channel Gain error Gain drift Bipolar zero error Bipolar zero drift Dynamic Performance (8) THD+N Dynamic range Signal-to-noise ratio Channel separation (1) (2) (3) (4) (5) (6) (7) (8) 2 VIN = –0.5 dB VIN = –60 dB A-weighted A-weighted 86 86 84 –86 –28 90 90 88 –80 dB dB dB dB High-pass filter bypassed (7) High-pass filter bypassed (7) ±1 ±2 ±20 ±1.7 ±20 ±3 ±5 % of FSR % of FSR ppm of FSR/°C % of FSR ppm of FSR/°C Bits VDC
VOL (5) CLOCK FREQUENCY fs
kHz MHz
Pins 7, 8, 17 and 18: RST, ML, MD, and MC for the PCM3002; PDAD, PDDA, DEM1, and DEM0 for PCM3003 (Schmitt-trigger input with 100-kΩ typical internal pulldown resistor) Pins 9, 10, 11, 15: SYSCLK, LRCIN, BCKIN, DIN (Schmitt-trigger input) Pin 16: 20BIT for PCM3003 (Schmitt-trigger input, 100-kΩ typical internal pulldown resistor) Pin 12: DOUT Pin 16: ZFLG for PCM3002 (open-drain output) See Application Bulletin SBAA033 for information relating to operation at lower sampling frequencies. High-pass filter for offset cancel fIN = 1 kHz, using the System Two™ audio measurement system by Audio Precision™ in rms mode with 20-kHz LPF, 400-Hz HPF used for performance calculation.
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
ELECTRICAL CHARACTERISTICS (continued)
All specifications at TA = 25°C, VDD = VCC = 3 V, fS = 44.1 kHz, SYSCLK = 384 fS, and 16-bit data, unless otherwise noted
PARAMETER Digital Filter Performance Pass band Stop band Pass-band ripple Stop-band attenuation Delay time HPF frequency response Analog Input Voltage range Center voltage Input impedance Antialiasing filter frequency response DAC CHARACTERISTICS Resolution DC Accuracy Gain mismatch, channelto-channel Gain error Gain drift Bipolar zero error Bipolar zero drift Dynamic Performance (9) THD+N Dynamic range Signal-to-noise ratio Channel separation Digital Filter Performance Pass band Stop band Pass-band ripple Stop-band attenuation Delay time Analog Output Voltage range Center voltage Load impedance LPF frequency response (9) AC coupling f = 20 kHz 10 –0.16 0.6 VCC 0.5 VCC Vp-p VDC kΩ dB –35 11.1/fS 0.555 fS ±0.17 0.445 fS Hz Hz dB dB s VOUT = 0 dB (full scale) VOUT = –60 dB EIAJ, A-weighted EIAJ, A-weighted 88 88 86 –86 –32 94 94 91 –80 dB dB dB dB ±1 ±1 ±20 ±2.5 ±20 ±3 ±5 % of FSR % of FSR ppm of FSR/°C % of FSR ppm of FSR/°C 20 Bits –3 dB 0.6 VCC 0.5 VCC 30 150 Vp-p VDC kΩ kHz –3 dB –65 17.4/fS 0.019 fS 0.583 fS ±0.05 0.454 fS Hz Hz dB dB s mHz CONDITIONS PCM3002E/3003E MIN TYP MAX UNITS
fOUT = 1 kHz, using the System Two audio measurement system by Audio Precision in rms mode with 20-kHz LPF, 400-Hz HPF used for performance calculation.
3
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
All specifications at TA = 25°C, VDD = VCC = 3 V, fS = 44.1 kHz, SYSCLK = 384 fS, and 16-bit data, unless otherwise noted
PARAMETER POWER SUPPLY REQUIREMENTS VCC, VDD Supply voltage Supply current –25°C to 85°C 0° C to 70°C (10) Operation, VCC = VDD = 3 V Power down, VCC = VDD = 3 V Operation, VCC = VDD = 3 V Power dissipation TEMPERATURE RANGE TA Tstg θJA Operation Storage Thermal resistance –25 –55 100 85 125 °C °C °C/W Power down (11), VCC = VDD = 3V 2.7 2.4 3 3 18 50 54 150 72 3.6 3.6 24 VDC VDC mA µA mW µW CONDITIONS PCM3002E/3003E MIN TYP MAX UNITS
(10) Applies for voltages between 2.4 V and 2.7 V for 0°C to 70°C and 256 fS/512 fS operation (384 fS not available) (11) SYSCLK, BCKIN, and LRCIN are stopped.
PACKAGE/ORDERING INFORMATION
PRODUCT PCM3002E PCM3003E PACKAGE TYPE 24-pin SSOP 24-pin SSOP PACKAGE CODE DB DB PACKAGE MARKING PCM3002E PCM3003E ORDERING NUMBER PCM3002E PCM3002E/2K PCM3003E PCM3003E/2K TRANSPORT MEDIA Rails Tape and reel Rails Tape and reel QUANTITY 58 2000 58 2000
ABSOLUTE MAXIMUM RATINGS
Supply voltage VDD, VCC1, VCC2 Supply voltage differences GND voltage differences Digital input voltage Analog input voltage Power dissipation Input current (any pins except supplies) Operating temperature Storage temperature Lead temperature, soldering Package temperature (IR reflow, peak) –0.3 V to 6.5 V ±0.1 V ±0.1 V –0.3 V to VDD + 0.3 V, < 6.5 V –0.3 V to VCC1, VCC2 + 0.3 V, < 6.5 V 300 mW ±10 mA –25°C to 85°C –55°C to 125°C 260°C, 5 s 235°C
4
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range
MIN Analog supply voltage, VCC1, VCC2 Digital supply voltage, VDD Analog input voltage, full scale (–0 dB) Digital input logic family Digital input clock frequency Analog output load resistance Analog output load capacitance Digital output load capacitance Operating free-air temperature, TA
PCM3002 (TOP VIEW)
NOM 3 3 1.8 CMOS
MAX 3.6 3.6
UNIT V V Vp-p
2.7 2.7 VCC = 3 V System clock Sampling clock 8.192 32 10
24.576 48 30 10
MHz kHz kΩ pF pF
–25
PCM3003 (TOP VIEW) 24 23 22 21 20 19 18 17 16 15 14 13
85
°C
VCC1 VCC1 VINR VREF1 VREF2 VINL RST ML SYSCLK LRCIN BCKIN DOUT
1 2 3 4 5 6 7 8 9 10 11 12
VCC2 AGND1 AGND2 VCOM VOUTR VOUTL MC MD ZFLG DIN VDD DGND
VCC1 VCC1 VINR VREF1 VREF2 VINL PDAD PDDA SYSCLK LRCIN BCKIN DOUT
1 2 3 4 5 6 7 8 9 10 11 12
24 23 22 21 20 19 18 17 16 15 14 13
VCC2 AGND1 AGND2 VCOM VOUTR VOUTL DEM0 DEM1 20BIT DIN VDD DGND
P0004-02
PIN ASSIGNMENTS—PCM3002
NAME AGND1 AGND2 BCKIN DGND DIN DOUT LRCIN MC MD ML RST SYSCLK VCC1 VCC2 VCOM VDD (1) (2) PIN 23 22 11 13 15 12 10 18 17 8 7 9 1, 2 24 21 14 I/O – – I – I O I I I I I I – – – – ADC analog ground DAC analog ground Bit clock input (1) Digital ground Data input (1) Data output Sample rate clock input (fs) (1) Bit clock for mode control (1) (2) Serial data for mode control (1) (2) Strobe pulse for mode control (1) (2) Reset, active LOW (1) (2) System clock input (1) ADC analog power supply DAC analog power supply ADC/DAC common Digital power supply DESCRIPTION
Schmitt-trigger input With 100-kΩ typical internal pulldown resistor 5
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
PIN ASSIGNMENTS—PCM3002 (continued)
NAME VINL VINR VOUTL VOUTR VREF1 VREF2 ZFLG (3) Open-drain output PIN 6 3 19 20 4 5 16 I/O I I O O – – O ADC analog input, Lch ADC analog input, Rch DAC analog output, Lch DAC analog output, Rch ADC reference 1 ADC reference 2 Zero flag output, active LOW (3) DESCRIPTION
PIN ASSIGNMENTS—PCM3003
NAME AGND1 AGND2 BCKIN DEM0 DEM1 DGND DIN DOUT LRCIN PDAD PDDA SYSCLK VCC1 VCC2 VCOM VDD VINL VINR VOUTL VOUTR VREF1 VREF2 20BIT (1) (2) PIN 23 22 11 18 17 13 15 12 10 7 8 9 1, 2 24 21 14 6 3 19 20 4 5 16 I/O – – I I I – I O I I I I – – – – I I O O – – I ADC analog ground DAC analog ground Bit clock input (1) De-emphasis control 0 (1) (2) De-emphasis control 1 (1) (2) Digital ground Data input (1) Data output Sample rate clock input (fs) (1) ADC power down, active LOW (1) (2) DAC power down, active LOW (1) (2) System clock input (1) ADC analog power supply DAC analog power supply ADC/DAC common Digital power supply ADC analog input, Lch ADC analog input, Rch DAC analog output, Lch DAC analog output, Rch ADC reference 1 ADC reference 2 20-bit format select(1)(2) DESCRIPTION
Schmitt-trigger input With 100-kΩ typical internal pulldown resistor
6
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
TYPICAL PERFORMANCE CURVES
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, fSYSCLK = 384 fS, and fSIGNAL = 1 kHz, unless otherwise noted
ADC SECTION
THD+N vs TEMPERATURE
THD+N − Total Harm. Dist. + Noise at −0.5 dB − % THD+N − Total Harm. Dist. + Noise at −60 dB − % 0.010 5
94
DYNAMIC RANGE and SNR vs TEMPERATURE
94
0.008
−60 dB
4
92 Dynamic Range − dB
Dynamic Range
92
0.006 −0.5 dB
3
90
SNR
90
0.004
2
88
88
0.002 −25
0
25
50
75
1 100
G001
86 −25
0
25
50
75
86 100
G002
TA − Free-Air Temperature − °C
TA − Free-Air Temperature − °C
Figure 1. THD+N vs SUPPLY VOLTAGE
THD+N − Total Harm. Dist. + Noise at −0.5 dB − % THD+N − Total Harm. Dist. + Noise at −60 dB − % 0.010 5
94
Figure 2. DYNAMIC RANGE and SNR vs SUPPLY VOLTAGE
94
0.008
4
92 Dynamic Range − dB
Dynamic Range
92
0.006
3
90 SNR
90
0.004
−0.5 dB
2
88
88
0.002 2.1
2.4
2.7
3.0
3.3
3.6
1 3.9
G003
86 2.1
2.4
2.7
3.0
3.3
3.6
86 3.9
G004
VCC − Supply Voltage − V
VCC − Supply Voltage − V
Figure 3.
Figure 4.
NOTE: All characteristics at supply voltages from 2.4 V to 2.7 V are measured at SYSCLK = 256 fS.
SNR − Signal-to-Noise Ratio − dB
−60 dB
SNR − Signal-to-Noise Ratio − dB
7
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
TYPICAL PERFORMANCE CURVES (continued)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, fSYSCLK = 384 fS, and fSIGNAL = 1 kHz, unless otherwise noted
THD+N vs SAMPLING FREQUENCY
THD+N − Total Harm. Dist. + Noise at −0.5 dB − % THD+N − Total Harm. Dist. + Noise at −60 dB − % 0.010 5
94
DYNAMIC RANGE and SNR vs SAMPLING FREQUENCY
94
0.008
4
92 Dynamic Range − dB Dynamic Range
92
0.006
3
90 SNR 88
90
0.004
−0.5 dB
2
88
0.002 32 44.1 48 fS − Sampling Frequency − kHz
1
86 32 44.1 48 fS − Sampling Frequency − kHz
86
G005
G006
Figure 5.
Figure 6.
DAC SECTION
THD+N vs TEMPERATURE
THD+N − Total Harm. Dist. + Noise at −60 dB − % 0.010 THD+N − Total Harm. Dist. + Noise at FS − % 4
98
DYNAMIC RANGE and SNR vs TEMPERATURE
98
0.008
−60 dB
3
96 Dynamic Range − dB Dynamic Range
96
0.006
2
94
94
SNR 92 92
0.004
FS 1
0.002 −25
0
25
50
75
0 100
G007
90 −25
0
25
50
75
90 100
G008
TA − Free-Air Temperature − °C
TA − Free-Air Temperature − °C
Figure 7.
Figure 8.
8
SNR − Signal-to-Noise Ratio − dB
SNR − Signal-to-Noise Ratio − dB
−60 dB
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
TYPICAL PERFORMANCE CURVES (continued)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, fSYSCLK = 384 fS, and fSIGNAL = 1 kHz, unless otherwise noted
THD+N vs SUPPLY VOLTAGE
THD+N − Total Harm. Dist. + Noise at −60 dB − % 0.010 THD+N − Total Harm. Dist. + Noise at FS − % 4
98
DYNAMIC RANGE and SNR vs SUPPLY VOLTAGE
98
0.008
−60 dB
3
96 Dynamic Range − dB Dynamic Range 94
96
0.006
2
94
FS 0.004 1
SNR 92 92
0.002 2.1
2.4
2.7
3.0
3.3
3.6
0 3.9
G009
90 2.1
2.4
2.7
3.0
3.3
3.6
90 3.9
G010
VCC − Supply Voltage − V
VCC − Supply Voltage − V
Figure 9.
Figure 10.
NOTE: All characteristics at supply voltages from 2.4 V to 2.7 V are measured at SYSCLK = 256 fS.
THD+N vs SAMPLING FREQUENCY and SYSTEM CLOCK
THD+N − Total Harm. Dist. + Noise at −60 dB − % 0.010 THD+N − Total Harm. Dist. + Noise at FS − % 4
98
DYNAMIC RANGE and SNR vs SAMPLING FREQUENCY and SYSTEM CLOCK
98
256 fS, 512 fS 96 Dynamic Range − dB
SNR
0.008
−60 dB
3
384 fS 256 fS, 512 fS
96
0.006
384 fS
2 FS
256 fS, 512 fS
94
Dynamic Range
94
0.004
1
92
384 fS
92
0.002 32 44.1 48 fS − Sampling Frequency − kHz
0
90 32 44.1 48 fS − Sampling Frequency − kHz
90
G011
G012
Figure 11.
Figure 12.
SNR − Signal-to-Noise Ratio − dB
SNR − Signal-to-Noise Ratio − dB
9
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
TYPICAL PERFORMANCE CURVES (continued)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, fSYSCLK = 384 fS, and fSIGNAL = 1 kHz, unless otherwise noted
OUTPUT SPECTRUM
ADCs
OUTPUT SPECTRUM (–0.5 dB, N = 8192)
0 −20 −40 Amplitude − dB −60 −80 −100 −120 −140 0 5 10 15 20 25
G013
OUTPUT SPECTRUM (–60 dB, N = 8192)
0 −20 −40 Amplitude − dB −60 −80 −100 −120 −140 0 5 10 15 20 25
G015
f − Frequency − kHz
f − Frequency − kHz
Figure 13. THD+N vs SIGNAL LEVEL
100 THD+N − Total Harmonic Distortion + Noise − %
Figure 14.
10
1
0.1
0.01
0.001 −96
−84
−72
−60
−48
−36
−24
−12
0
G017
Signal Level − dB
Figure 15.
10
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
TYPICAL PERFORMANCE CURVES (continued)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, fSYSCLK = 384 fS, and fSIGNAL = 1 kHz, unless otherwise noted
DACs
OUTPUT SPECTRUM (0 dB, N = 8192)
0 −20 −40 Amplitude − dB −60 −80 −100 −120 −140 0 5 10 15 20 25
G014
OUTPUT SPECTRUM (–60 dB, N = 8192)
0 −20 −40 Amplitude − dB −60 −80 −100 −120 −140 0 5 10 15 20 25
G016
f − Frequency − kHz
f − Frequency − kHz
Figure 16. THD+N vs SIGNAL LEVEL
100 THD+N − Total Harmonic Distortion + Noise − %
Figure 17.
10
1
0.1
0.01
0.001 −96
−84
−72
−60
−48
−36
−24
−12
0
G018
Signal Level − dB
Figure 18.
11
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
TYPICAL PERFORMANCE CURVES
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, fSYSCLK = 384 fS, DIN = BPZ, and VIN = BPZ, unless otherwise noted
SUPPLY CURRENT
ICC + IDD vs SUPPLY VOLTAGE
25 2.5 25
ICC + IDD vs TEMPERATURE
2.5
ICC + IDD: Power Down and Off − mA
20 ADC and DAC ICC + IDD − mA 15 ADC 10 DAC 5 Power Down and Off 0 2.1 2.4 2.7 3.0 3.3 3.6
2.0
20
ADC and DAC
2.0
1.5
15 ADC 10 DAC 5
1.5
1.0
1.0
0.5
0.5 Power Down and Off
0 3.9
G020
0 −50
−25
0
25
50
75
0 100
G019
VCC − Supply Voltage − V
TA − Free-Air Temperature − °C
Figure 19.
Figure 20.
All characteristics at supply voltages from 2.4 V to 2.7 V are measured at SYSCLK = 256 fS.
ICC + IDD vs SAMPLING FREQUENCY
20 ADC and DAC 19 512 fS ICC + IDD − mA 18 256 fS 17
16
15 32 44.1 48
G021
fS − Sampling Frequency − kHz
Figure 21.
12
ICC + IDD: Power Down and Off − mA
ICC + IDD − mA
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
TYPICAL PERFORMANCE CURVES OF INTERNAL FILTERS (ADCs)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, and fSYSCLK = 384 fS, unless otherwise noted
DECIMATION FILTER
OVERALL CHARACTERISTICS
0 0
STOP-BAND ATTENUATION CHARACTERISTICS
−20 −50 Amplitude − dB Amplitude − dB 0 8 16 24 32
G022
−40
−100
−60
−150 −80
−200 Normalized Frequency [× fS Hz]
−100 0.0
0.2
0.4
0.6
0.8
1.0
G023
Normalized Frequency [× fS Hz]
Figure 22. PASS-BAND RIPPLE CHARACTERISTICS
0.2 0 −1 0.0 −2 −3 Amplitude − dB −4 −5 −6 −7 −8 −9 −1.0 0.0
Figure 23. TRANSITION BAND CHARACTERISTICS
Amplitude − dB
−0.2
−0.4
−0.6
−0.8
0.1
0.2
0.3
0.4
0.5
G024
−4.13 dB at 0.5 fS −10 0.45 0.47 0.49
0.51
0.53
0.55
G025
Normalized Frequency [× fS Hz]
Normalized Frequency [× fS Hz]
Figure 24.
Figure 25.
13
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
TYPICAL PERFORMANCE CURVES OF INTERNAL FILTERS (ADCs) (continued)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, and fSYSCLK = 384 fS, unless otherwise noted
HIGH-PASS FILTER
HIGH-PASS FILTER RESPONSE
0 −10 −20 −30 Amplitude − dB −40 −50 −60 −70 −80 −90 −100 0.0 −1.0 0.1 0.2 0.3 0.4 0.5
G026
HIGH-PASS FILTER RESPONSE
0.2
0.0
Amplitude − dB
−0.2
−0.4
−0.6
−0.8
0
1
2
3
4
G027
Normalized Frequency [× fS/1000 Hz]
Normalized Frequency [× fS/1000 Hz]
Figure 26.
Figure 27.
ANTIALIASING FILTER
ANTIALIASING FILTER OVERALL FREQUENCY RESPONSE
0 0.2
ANTIALIASING FILTER PASS-BAND FREQUENCY RESPONSE
−10
0.0
Amplitude − dB
−20
Amplitude − dB 1 10 100 1k 10k 100k 1M 10M
G028
−0.2
−0.4
−30
−0.6
−40
−0.8
−50 f − Frequency − Hz
−1.0 1 10 100 1k 10k 100k
G029
f − Frequency − Hz
Figure 28.
Figure 29.
14
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
TYPICAL PERFORMANCE CURVES OF INTERNAL FILTERS (DACs)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, and fSYSCLK = 384 fS, unless otherwise noted
DIGITAL FILTER
OVERALL FREQUENCY CHARACTERISTICS (fS = 44.1 kHz)
0 0.00
PASS-BAND RIPPLE CHARACTERISTICS (fS = 44.1 kHz)
−20
−0.20
Level − dB
−60
Level − dB 0 25k 50k 75k 100k 125k 150k 175k
G030
−40
−0.40
−0.60
−80
−0.80
−100 f − Frequency − Hz
−1.00 0 5k 10k f − Frequency − Hz
G031
15k
20k
Figure 30.
Figure 31.
DE-EMPHASIS FILTER
DE-EMPHASIS FREQUENCY RESPONSE (32 kHz)
0 0.6
DE-EMPHASIS ERROR (32 kHz)
−2
0.4
−4 Level − dB Error − dB 0 5k 10k 15k 20k 25k
G032
0.2
−6
0.0
−8
−0.2
−10
−0.4
−12 f − Frequency − Hz
−0.6 0 3628 7256 f − Frequency − Hz
G033
10884
14512
Figure 32.
Figure 33.
15
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
TYPICAL PERFORMANCE CURVES OF INTERNAL FILTERS (DACs) (continued)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, and fSYSCLK = 384 fS, unless otherwise noted
DE-EMPHASIS FREQUENCY RESPONSE (44.1 kHz)
0 0.6
DE-EMPHASIS ERROR (44.1 kHz)
−2
0.4
−4 Level − dB Error − dB 0 5k 10k 15k 20k 25k
G034
0.2
−6
0.0
−8
−0.2
−10
−0.4
−12 f − Frequency − Hz
−0.6 0 4999.8375 9999.675 14999.5125 19999.35
G035
f − Frequency − Hz
Figure 34. DE-EMPHASIS FREQUENCY RESPONSE (48 kHz)
0 0.6
Figure 35. DE-EMPHASIS ERROR (48 kHz)
−2
0.4
−4 Level − dB Error − dB 0 5k 10k 15k 20k 25k
G036
0.2
−6
0.0
−8
−0.2
−10
−0.4
−12 f − Frequency − Hz
−0.6 0 5442 10884 f − Frequency − Hz
G037
16326
21768
Figure 36.
Figure 37.
16
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
TYPICAL PERFORMANCE CURVES OF INTERNAL FILTERS (DACs) (continued)
All specifications at TA = 25°C, VCC = VDD = 3 V, fS = 44.1 kHz, and fSYSCLK = 384 fS, unless otherwise noted
ANALOG LOW-PASS FILTER
INTERNAL ANALOG FILTER FREQUENCY RESPONSE (1 Hz–10 MHz)
20
INTERNAL ANALOG FILTER FREQUENCY RESPONSE (1 Hz–100 kHz)
0.15
0
0.10
−20 Level − dB Level − dB 1 10 100 1k 10k 100k 1M 10M
G038
0.05
−40
0.00
−60
−0.05
−80
−0.10
−100 f − Frequency − Hz
−0.15 1 10 100 1k 10k 100k
G039
f − Frequency − Hz
Figure 38.
Figure 39.
17
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
BLOCK DIAGRAM
(+) VINL Analog Front-End Circuit (−) Delta-Sigma Modulator Decimation and High-Pass Filter LRCIN
VREF1 VCOM VREF2
BCKIN Reference
ADC
Serial Data Interface DIN
(−) VINR Analog Front-End Circuit Delta-Sigma Modulator Decimation and High-Pass Filter DOUT
(+)
MC(1)/DEM0(2)
VOUTL
Analog Low-Pass Filter
Multilevel Delta-Sigma Modulator
Interpolation Filter 8× Oversampling
Mode Control Interface
MD(1)/DEM1(2)
ML(1) 20BIT(2)
DAC
Analog Low-Pass Filter Multilevel Delta-Sigma Modulator
Interpolation Filter 8× Oversampling
VOUTR
Reset and Power Down
PDDA(2) RST(1)/PDAD(2)
Power Supply
Clock
Zero Detect(1)
AGND2
VCC2
AGND1
VCC1
DGND
VDD
SYSCLK
ZFLG(1)
B0004-03
(1) (2)
MC, MD, ML, RST, and ZFLG are for PCM3002 only. DEM0, DEM1, 20BIT, PDAD, and PDDA are for PCM3003 only.
18
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
1.0 µF + 3
VINR 30 kΩ
− − + + (−) (+)
21 4.7 µF + 4 4.7 µF + 5 4.7 µF +
VCOM Delta-Sigma Modulator VREF1
VREF2
VREF
S0011-03
Figure 40. Analog Front-End (Single-Channel)
PCM AUDIO INTERFACE
The four-wire digital audio interface for the PCM3002/3003 comprises LRCIN (pin 10), BCKIN (pin 11), DIN (pin 15), and DOUT (pin 12). The PCM3002 can be used with any of the four input/output data formats (formats 0–3), while the PCM3003 can only be used with selected input/output formats (formats 0–1). For the PCM3002, these formats are selected through program register 3 in the software mode. For the PCM3003, data formats are selected by the 20BIT input (pin 16). Figure 41, Figure 42, and Figure 43 illustrate audio data input/output formats and timing. The PCM3002/3003 can accept 32, 48, or 64 bit clocks (BCKIN) in one clock of LRCIN. Only the 16-bit data format can be selected when 32-bit clocks/LRCIN are applied.
19
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
FORMAT 0: PCM3002/3003
DAC: 16-Bit, MSB-First, Right-Justified LRCIN BCKIN DIN 16 1 2 3 14 15 16 LSB 1 2 3 14 15 16 LSB Left-Channel Right-Channel
MSB
MSB
ADC: 16-Bit, MSB-First, Left-Justified LRCIN BCKIN DOUT 1 2 3 14 15 16 LSB 1 2 3 14 15 16 LSB 1 Left-Channel Right-Channel
MSB
MSB
FORMAT 1: PCM3002/3003
DAC: 20-Bit, MSB-First, Right-Justified LRCIN BCKIN DIN 20 1 2 3 18 19 20 LSB 1 2 3 18 19 20 LSB Left-Channel Right-Channel
MSB
MSB
ADC: 20-Bit, MSB-First, Left-Justified LRCIN BCKIN DOUT 1 2 3 18 19 20 LSB 1 2 3 18 19 20 LSB
T0016-04
Left-Channel
Right-Channel
1
MSB
MSB
Figure 41. Audio Data Input/Output Format
20
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
FORMAT 2: PCM3002 Only
DAC: 20-Bit, MSB-First, Left-Justified LRCIN BCKIN DIN 1 2 3 18 19 20 LSB 1 2 3 18 19 20 LSB 1 Left-Channel Right-Channel
MSB
MSB
ADC: 20-Bit, MSB-First, Left-Justified LRCIN BCKIN DOUT 1 2 3 18 19 20 LSB 1 2 3 18 19 20 LSB 1 Left-Channel Right-Channel
MSB
MSB
FORMAT 3: PCM3002 Only
DAC: 20-Bit, MSB-First, I2S LRCIN BCKIN DIN 1 2 3 18 19 20 LSB 1 2 3 18 19 20 LSB Left-Channel Right-Channel
MSB
MSB
ADC: 20-Bit, MSB-First, I2S LRCIN BCKIN DOUT 1 2 3 18 19 20 LSB 1 2 3 18 19 20 LSB
T0016-05
Left-Channel
Right-Channel
MSB
MSB
Figure 42. Audio Data Input/Output Format (PCM3002)
21
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
t(LRP) LRCIN t(BCL) t(BCH) t(BL) 0.5 VDD t(BCY) t(DIS) t(DIH) t(LB) 0.5 VDD
BCKIN
DIN t(BDO) t(LDO)
0.5 VDD
DOUT
0.5 VDD
T0021−01
BCKIN pulse cycle time BCKIN pulse duration, HIGH BCKIN pulse duration, LOW BCKIN rising edge to LRCIN edge LRCIN edge to BCKIN rising edge LRCIN pulse duration DIN setup time DIN hold time DOUT delay time to BCKIN falling edge DOUT delay time to LRCIN edge Rising time of all signals Falling time of all signals
t(BCY) t(BCH) t(BCL) t(BL) t(LB) t(LRP) t(DIS) t(DIH) t(BDO) t(LDO) t(RISE) t(FALL)
300 ns (min) 120 ns (min) 120 ns (min) 40 ns (min) 40 ns (min) t(BCY) (min) 40 ns (min) 40 ns (min) 40 ns (max) 40 ns (max) 20 ns (max) 20 ns (max)
Figure 43. Audio Data Input/Output Timing
SYSTEM CLOCK
The system clock for the PCM3002/3003 must be either 256 fS, 384 fS, or 512 fS, where fS is the audio sampling frequency. The system clock should be provided at the SYSCLK input (pin 9). The PCM3002/3003 also has a system-clock detection circuit that automatically senses if the system clock is operating at 256 fS, 384 fS, or 512 fS. When a 384-fS or 512-fS system clock is used, the clock is divided to 256 fS automatically. The 256-fS clock is used to operate the digital filters and the delta-sigma modulators. Table 1 lists the relationship of typical sampling frequencies and system clock frequencies; Figure 44 illustrates the system clock timing. Table 1. System Clock Frequencies
SAMPLING RATE FREQUENCY (kHz) 256 fs 32 44.1 48 8.1920 11.2896 12.2880 SYSTEM CLOCK FREQUENCY (MHz) 384 fs 12.2880 16.9344 18.4320 512 fs 16.3840 22.5792 24.5760
22
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
t(SCKH) H SYSCLK L t(SCKL) 1/256 fS, 1/384 fS, or 1/512 fS
T0005-05
0.7 VDD 0.3 VDD
Figure 44. System Clock Timing
System clock pulse duration, HIGH System clock pulse duration, LOW t(SCKH) t(SCKL) 12 ns (min) 12 ns (min)
POWER-ON RESET Both the PCM3002 and PCM3003 have internal power-on reset circuitry. Power-on reset occurs when the system clock (SYSCLK) is active and VDD > 2.2 V. For the PCM3003, the SYSCLK must complete a minimum of three complete cycles prior to VDD > 2.2 V to ensure proper reset operation. The initialization sequence requires 1024 SYSCLK cycles for completion, as shown in Figure 45. Figure 46 shows the state of the DAC and ADC outputs during and after the reset sequence.
2.4 V 2.2 V 2.0 V
VDD
Reset Internal Reset
Reset Removal
3 Clocks Minimum 1024 System Clock Periods
System Clock
T0014-03
Figure 45. Internal Power-On Reset Timing
23
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
Reset Removal or Power Down Off Internal Reset or Power Down Reset Power Down t(DACDLY1) (16384/fS) DAC VOUT GND VCOM (0.5 VCC) t(ADCDLY1) (18432/fS) ADC DOUT Zero Data Zero Data Normal Data(1)
T0019-02
Ready/Operation
(1)
The HPF transient response (exponentially attenuated signal from ±0.2% dc of FSR with 200-ms time constant) appears initially.
Figure 46. DAC Output and ADC Output for Reset and Power Down EXTERNAL RESET The PCM3002 includes a reset input, RST (pin 7), while the PCM3003 uses both PDAD (pin 7) and PDDA (pin 8) for external reset control. As shown in Figure 47, the external reset signal must drive RST or PDAD and PDDA low for a minimum of 40 nanoseconds while SYSCLK is active in order to initiate the reset sequence. Initialization starts on the rising edge of RST or PDAD and PDDA, and requires 1024 SYSCLK cycles for completion. Figure 46 shows the state of the DAC and ADC outputs during and after the reset sequence.
RST or PDAD and PDDA RST Pulse Duration t(RST) = 40 ns (min)
t(RST) Reset Internal Reset 1024 System Clock Periods System Clock
T0015-02
Reset Removal
Figure 47. External Forced-Reset Timing SYNCHRONIZATION WITH THE DIGITAL AUDIO SYSTEM The PCM3002/3003 operates with LRCIN synchronized to the system clock. The PCM3002/3003 does not require any specific phase relationship between LRCIN and the system clock, but there must be synchronization of LRCIN and the system clock. If the synchronization between the system clock and LRCIN changes more than 6 bit clocks (BCKIN) during one sample (LRCIN) period because of phase jitter on LRCIN, internal operation of the DAC stops within 1/fS, and the analog output is forced to bipolar zero (0.5 VCC) until the system clock is resynchronized to LRCIN followed by t(DACDLY2) delay time. Internal operation of the ADC also stops within 1/fS, and the digital output codes are set to bipolar zero until resynchronization occurs followed by t(ADCDLY2) delay time. If LRCIN is synchronized within 5 or fewer bit clocks to the system clock, operation is normal. Figure 48 illustrates the effects on the output when synchronization is lost. Before the outputs are forced to bipolar zero ( 10 kΩ, depending on system performance requirements MC, MD, ML, ZFLG, RST, and 10-kΩ pullup resistor are for the PCM3002. DEM0, DEM1, 20BIT, PDAD, PDDA are for the PCM3003.
Figure 51. Typical Connection Diagram for PCM3002/3003
33
PCM3002 PCM3003
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
www.ti.com
THEORY OF OPERATION ADC SECTION
The PCM3002/3003 ADC consists of two reference circuits, a stereo single-to-differential converter, a fully differential fifth-order delta-sigma modulator, a decimation filter (including digital high pass), and a serial interface circuit. The block diagram in this data sheet illustrates the architecture of the ADC section, Figure 40 shows the single-to-differential converter, and Figure 52 illustrates the architecture of the fifth-order delta-sigma modulator and transfer functions. An internal reference circuit with three external capacitors provides all reference voltages required by the ADC, which defines the full-scale range for the converter. The internal single-to-differential voltage converter saves the space and extra parts needed for the external circuitry required by many delta-sigma converters. The internal full-differential signal processing architecture provides a wide dynamic range and excellent power supply rejection performance. The input signal is sampled at a 64× oversampling rate, eliminating the need for a sample-and-hold circuit, and simplifying antialias filtering requirements. The fifth-order delta-sigma noise shaper consists of five integrators which use a switched-capacitor topology, a comparator, and a feedback loop consisting of a one-bit DAC. The delta-sigma modulator shapes the quantization noise, shifting it out of the audio band in the frequency domain. The high order of the modulator enables it to randomize the modulator outputs, reducing idle tone levels. The 64-fS, one-bit data stream from the modulator is converted to 1-fS, 16/20-bit data words by the decimation filter, which also acts as a low-pass filter to remove the shaped quantization noise. The dc components are removed by a high-pass filter function contained within the decimation filter.
DAC SECTION
The delta-sigma DAC section of the PCM3002/3003 is based on a 5-level amplitude quantizer and a third-order noise shaper. This section converts the oversampled input data to a 5-level delta-sigma format. A block diagram of the 5-level delta-sigma modulator is shown in Figure 53. This 5-level delta-sigma modulator has the advantage of improved stability and reduced clock-jitter sensitivity over the typical one-bit (2-level) delta-sigma modulator. The combined oversampling rate of the delta-sigma modulator and the internal 8× interpolation filter is 64 fS for a 256-fS system clock. The theoretical quantization noise performance of the 5-level delta-sigma modulator is shown in Figure 54.
Analog In X(z) + −
1st SW-CAP Integrator
+
−
2nd SW-CAP Integrator
3rd SW-CAP Integrator
+
−
4th SW-CAP Integrator
5th SW-CAP Integrator
Qn(z)
+
+
+
+
+
+
+
+
Digital Out Y(z)
H(z)
Comparator
1-Bit DAC
Y(z) = STF(z) * X(z) + NTF(z) * Qn(z) Signal Transfer Function STF(z) = H(z) / [1 + H(z)] Noise Transfer Function NTF(z) = 1 / [1 + H(z)]
B0005-01
Figure 52. Simplified Fifth-Order Delta-Sigma Modulator
34
PCM3002 PCM3003
www.ti.com
SBAS079A – OCTOBER 2000 – REVISED OCTOBER 2004
THEORY OF OPERATION (continued)
In 8 fS 21-Bit
+
+ − Z−1
+
+ − Z−1
+
+ Z−1
+ 5-Level Quantizer
+
+
4 3 Out 64 fS 2 1 0
B0008-01
Figure 53. Five-Level Delta-Sigma Modulator Block Diagram
0 −10 −20 −30 −40 −50 Gain − dB −60 −70 −80 −90 −100 −110 −120 −130 −140 −150 0 5 10 15 20 25 30
G040
f − Frequency − kHz
Figure 54. Quantization Noise Spectrum
35
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2007
PACKAGING INFORMATION
Orderable Device PCM3002E PCM3002E/2K PCM3002E/2KG4 PCM3002EG PCM3002EG/2K PCM3002EG/2KE6 PCM3002EG4 PCM3002EGE6 PCM3003E PCM3003E/2K PCM3003E/2KG4 PCM3003EG4
(1)
Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE
Package Type SSOP SSOP SSOP SSOP SSOP SSOP SSOP SSOP SSOP SSOP SSOP SSOP
Package Drawing DB DB DB DB DB DB DB DB DB DB DB DB
Pins Package Eco Plan (2) Qty 24 24 24 24 24 24 24 24 24 24 24 24 58 Green (RoHS & no Sb/Br)
Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU SNBI CU SNBI CU SNBI CU NIPDAU CU SNBI CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU
MSL Peak Temp (3) Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-1-260C-UNLIM Level-2-260C-1 YEAR Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM
2000 Green (RoHS & no Sb/Br) 2000 Green (RoHS & no Sb/Br) 58 2000 2000 58 58 58 Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Green (RoHS & no Sb/Br) Pb-Free (RoHS) Green (RoHS & no Sb/Br)
2000 Green (RoHS & no Sb/Br) 2000 Green (RoHS & no Sb/Br) 58 Green (RoHS & no Sb/Br)
The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
12-Jan-2007
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
28 PINS SHOWN 0,65 28 0,38 0,22 15 0,15 M
PLASTIC SMALL-OUTLINE
0,25 0,09 5,60 5,00 8,20 7,40
Gage Plane 1 A 14 0°– 8° 0,25 0,95 0,55
Seating Plane 2,00 MAX 0,05 MIN 0,10
PINS ** DIM A MAX
14
16
20
24
28
30
38
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30 4040065 /E 12/01
NOTES: A. B. C. D.
All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Mailing Address:
Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated