PWS726A

PWS725A PWS726A Isolated, Unregulated DC/DC CONVERTERS FEATURES q ISOLATED ±7 TO ±18VDC OUTPUT FROM SINGLE 7 TO 18VDC SUPPLY q ±15mA OUTPUT AT RATED VOLTAGE ACCURACY q HIGH ISOLATION VOLTAGE PWS725A, 1500Vrms PWS726A, 3500Vrms q LOW LEAKAGE CAPACITANCE: 9pF q LOW LEAKAGE CURRENT: 2µA max, at 240VAC 50/60Hz q HIGH RELIABILITY DESIGN q AVAILABLE WITH OUTPUT SYNCHRONIZATION SIGNAL FOR USE WITH ISO120 AND ISO121 q PROTECTED AGAINST OUTPUT FAULTS q COMPACT q LOW COST q EASY TO APPLY—FEW EXTERNAL PARTS APPLICA TIONS q MEDICAL EQUIPMENT q INDUSTRIAL PROCESS EQUIPMENT q TEST EQUIPMENT q DATA ACQUISITION DESCRIPTION The PWS725A and PWS726A convert a single 7 to 18VDC input to bipolar voltages of the same value as the input voltage. The converters are capable of providing ±15mA at rated voltage accuracy and up to ±40mA without damage. (See Output Current Rating.) The PWS725A and PWS726A converters provide reliable, engineered solutions where isolated power is required in critical applications. The high isolation voltage rating is achieved through use of a speciallydesigned transformer and physical spacing. An additional high dielectric-strength, low leakage transformer coating increases the isolation rating of the PWS726A. Reliability and performance are designed in. The bifilar wound, wirebonded transformer simultaneously provides lower output ripple than competing designs, and a higher performance/cost ratio. The soft-start oscillator/driver design assures full operation of the International Airport Industrial Park • Mailing Address: PO Box 11400 Tel: (520) 746-1111 • Twx: 910-952-1111 • Cable: BBRCORP • © 1987 Burr-Brown Corporation oscillator before either MOSFET driver turns on, protects the switches, and eliminates high inrush currents during turn-on. Input current sensing protects both the converter and the load from possible thermal damage during a fault condition. Special design features make these converters especially easy to apply. The compact size allows dense circuit layout while maintaining critical isolation requirements. The Input Sync connection allows frequency synchronization of multiple converters. The Output Sync is available to synchronize ISO120 and ISO121 isolation amplifiers. The Enable input allows control over output power in instances where shutdown is desired to conserve power, such as in battery-powered equipment, or where sequencing of power turn-on/turn-off is desired. • Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd. • Tucson, AZ 85706 Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® PDS-736D 1 PWS725A/726A Printed in U.S.A. October, 1993 SPECIFICATIONS ELECTRICAL TA = +25°C, CL = 1µF ceramic, VIN = 15VDC, operating frequency = 800kHz, VOUT = ±15VDC, CIN = 1µF ceramic, IOUT = ±15mA, unless otherwise specified. PWS725A PARAMETER INPUT Rated Voltage Input Voltage Range Input Current Input Current Ripple CONDITIONS MIN TYP 15 7 IO = ±15mA No External Filtering L-C Input Filter, LIN = 100µH, CIN = 1µF(1) C Only, CIN = 1µF Input to Output, 10 seconds Input to Output, 60 seconds, min Input to Output, Continuous, AC 60Hz Input to Output, Continuous DC Input to Output Input to Output, 240Vrms, 60Hz 4000 1500 1500 2121 1012 || 9 1.2 14.25 Balanced Loads Single-Ended Balanced Loads, ±10mA < IOUT < ±40mA No External Capacitor LO = 10µH, CO = 1µF (Figure 1) LO = 0µH, CO Filter Only LO = 10µH, CO = 1µF LO = 100µH, C Filter C Filter Only 15 15 2.0 15.75 40 80 0.4 * * * * * 77 150 5 60 8000 3500 3500 4950 * * * * * 18 * * * * MAX MIN PSW726A TYP * * MAX UNITS VDC VDC mA mAp-p mAp-p mAp-p VDC Vrms Vrms VDC Ω || pF µA VDC mA mA %/mA mVp-p mVp-p mVp-p µF µF % V/V mV/°C Vp-p °C °C °C ISOLATION Test Voltages Rated Voltage Isolation Impedance Leakage Current OUTPUT Rated Output Voltage Output Current Load Regulation Ripple Voltage (400kHz) 60 10 1 Output Switching Noise Output Capacitive Load Voltage Balance, V+, V– Sensitivity to ∆VIN Output Voltage Temp. Coefficient Output Sync Signal TEMPERATURE Specification Operating Storage * Specification same as PWS725A. * * See Performance Curves * 10 1 * * Square Wave, 50% Duty Cycle –25 –25 –25 0.04 1.15 10 30 +85 +85 +125 * * * * * * * PIN CONFIGURATION Top View –VO NC NC Output Ground 1 2 3 4 32 +VO 31 NC 30 Output Ground 29 Output Sync DIP PACKAGE INFORMATION(1) MODEL PWS725A PWS726A PACKAGE 32-Pin Ceramic DIP 32-Pin Ceramic DIP PACKAGE DRAWING NUMBER 210 210 NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix D of Burr-Brown IC Data Book. NC 13 Input Ground 14 Input Sync 15 VIN 16 20 Frequency Adjust 19 Frequency Adjust 18 Enable 17 NC The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® PWS725A/726A 2 TYPICAL PERFORMANCE CURVES TA = +25°C, VCC = ±15VDC unless otherwise noted. OUTPUT CAPACITANCE vs RIPPLE VOLTAGE 100 Output Ripple Voltage (mVp-p) LOAD REGULATION 20 90 80 70 60 50 40 30 20 10 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Capacitance (µF) Peak-to-Peak DC < f < 20MHz Capacitor Only L-C Filter, L = 100µH IO = ±15mA 18 VIN = +15V Output Voltage (V) VIN = ±15V 16 Balanced Loads 14 Single-ended Loads 12 10 0 10 20 20 40 Output Current (mA) 30 60 40 Balanced 80 Single MAXIMUM POWER DISSIPATION 2 LINE REGULATION 20 18 IO = ±15mA Output Power (W) Output Voltage (V) 1.44 16 14 12 10 8 6 1 0 –25 0 25 50 75 85 100 Temperature (°C) 4 6 7 8 10 12 Input Voltage (V) 14 16 18 INPUT CURRENT vs OUTPUT CURRENT 140 0 –1 Output Voltage (%) OUTPUT VOLTAGE DRIFT –2 –3 –4 –5 IIN (mA) 77 70 0 0 ±15 IO (mA) ±30 ±45 –6 –50 0 50 Temperature (°C) 85 100 ® 3 PWS725A/726A TYPICAL PERFORMANCE CURVES (CONT) TA = +25°C, VCC = ±15VDC unless otherwise noted. SYNC FREQUENCY vs INPUT CURRENT AND OUTPUT VOLTAGE VIN = +15V Output Voltage (V) Input Current (mA) LO(4) 32 Oscillator/ Driver Control Full-Wave Bridge Rectifier CO(4) 4 & 30 1 0.22µF 15 ±VOUT 90 80 14 IINPUT (IO = ±15mA) 70 60 400 800 1200 1600 SYNC Frequency (kHz) (Optional External Control) THEORY OF OPERATION The PWS725A and the PWS726A DC/DC converters consist of a free-running oscillator, control and switch driver circuitry, MOSFET switches, a transformer, a bridge rectifier, and filter capacitors together in a 32-pin DIP (0.900 inches nominal) package. The control circuitry consists of current limiting, soft start, frequency adjust, enable, and synchronization features. See Figure 1. In instances where several converters are used in a system, beat frequencies developed between the converters are a potential source of low frequency noise in the supply and ground paths. This noise may couple into signal paths. See Figures 2 and 3 for connection of INPUT SYNC pin. Converters can be synchronized and these beat frequencies avoided. The unit with the highest natural frequency will determine the synchronized running frequency. To avoid excess stray capacitance, the INPUT SYNC pin should not be loaded with more than 50pF. If unused, the INPUT SYNC must be left open. Soft start circuitry protects the MOSFET switches during start up. This is accomplished by holding the gate-to-source voltage of both MOSFET switches low until the freerunning oscillator is fully operational. In addition to that soft start circuitry, input current sensing also protects the MOSFET switches. This current limiting keeps the FET OUTPUT SYNC VIN 7-18/VDC LIN(5) CIN(5) 20kΩ Frequence Increase(1) 20 RSC 29 16 0.22µF +VOUT +IO – + – 0.22µF CO(4) LO(4) –VOUT Load –IO 19 18 15 14 ENABLE(3) INPUT SYNC(2) NOTES: (1) Frequency Adjust is optional, with pins 19 and 20 left open. The normal switching frequency is 800kHz. (2) Leave INPUT SYNC pin open if unused; limit stray capacitance on INPUT SYNC pin to less than 50pF. (3) Leave ENABLE pin open or connect to VIN if not used. (4) Optional output filtering, with LO = 0, limit CO ≤ 1µF, with LO = 100µH, limit CO ≤ 10µF, see Performance Curves for LO = 0. (5) Optional input filtering, see Performance Curves for LIN = 0. (6) CAUTION: Do not connect pin 29 to low impedance loads. See Figure 5. FIGURE 1. PWS725A/726A Functional Diagram. ® PWS725A/726A 4 Load + +7V to +18 V +7V to +18 V MC1472 or Equivalent Peripheral Driver +5V 16 Master PWS725A 15 4 +VCC OPA633 8 1 Slave PWS725A/726A 15 16 19(1) 8 3 4 620Ω 1/8W 100Ω 330Ω 1W 2N3904 PWS725A/726A 15 2N3904 16 19(1) Buffer –VCC TTL 2 SYNC Signal(2) Keep Connection Short NOTE: (1) Units to be synchronized should have a lower free-running frequency than the master unit. Grounding Frequency Adjust (pin 19) will shift the free-running frequency to approximately 400kHz. Slave PWS725A/726A 15 16 19 (1) To Other PWS725A/726A Converters NOTES: (1) Units to be synchronized should have a lower free-running frequency than the TTL signal. Grounding Frequency Adjust (Pin 19) will shift the free-running frequency to approximately 400kHz. (2) The TTL SYNC signal can have a frequency range of 450kHz to 1.5MHz. PWS725A/726A 15 16 19(1) FIGURE 2. Synchronization of Multiple PWS725As or PWS726As from a Master Converter. switches operating in their safe operating area under fault conditions or excessive loads. When either of these conditions occur, the peak input current exceeds a safe limit. The result is an approximate 5% duty cycle, 300µs drive period to the MOSFET switches. This protects the internal MOSFET switches as well as the external load from any thermal damage. When the fault or excessive load is removed, the converter resumes normal operation. A delay period of approximately 50µs incorporated in the current sensing circuitry allows the output filter capacitors to fully charge after a fault is removed. This delay period corresponds to a filter capacitance of no more than 1µF at either of the output pins. This provides full protection of the MOSFET switches and also sufficiently filters the output ripple voltage (see specification table). The current sensing circuitry is designed to provide thermal protection for the MOSFET switches over the operating temperature range as well. The low thermal resistance for the package (θJC = 10°C/W) ensures safe operation under rated conditions. When these rated conditions are exceeded, the unit will go into its shutdown mode. An optional potentiometer can be connected between the two FREQUENCY ADJUST pins to trim the oscillator operating frequency ±10% (see Figure 4). Care should be taken when trimming the frequency near the low frequency range. If the frequency is trimmed too low, the peak inductive currents in the primary will trip the input current sensing circuitry to protect the MOSFET switches from these peak inductive currents. The ENABLE pin allows external control of output power. When this pin is pulled low, output power is disabled. Logic thresholds are TTL compatible. When not used, the Enable input may be left open or tied to VIN (pin 16). 5 To Other PWS725A/726A Converters FIGURE 3. Synchronization of Multiple PWS725As or PWS726As from an External TTL Signal. PWS725A/726A Monitor frequency with scope or frequency counter (use low C probe). 15 19 20kΩ (1) 20 Frequency Increase +5VBE +4VBE 1.25µs Nominal SYNC Signal NOTE: (1) For nominal 800kHz operation, leave pins 19 and 20 open. FIGURE 4. Frequency Adjustment Procedure. OUTPUT CURRENT RATING The total current which can be drawn from the PWS725A or PWS726A is a function of total power being drawn from both outputs (see Functional Diagram). If one output is not used, then maximum current can be drawn from the other output. If both outputs are loaded, the total current must be limited such that: |IL+| + |IL–| ≤ 80mA It should be noted that many analog circuit functions do not simultaneously draw full rated current from both the positive and negatives supplies. For example, an operational amplifier may draw 13mA from the positive supply under ® PWS725A/726A full load while drawing only 3mA from the negative supply. Under these conditions, the PWS725A/726A could supply power for up to five devices (80mA ÷ 16mA ≈ 5). Thus, the PWS725A/726A can power more circuits than is at first apparent. ISOLATION VOLTAGE RATINGS Because a long-term test is impractical in a manufacturing situation, the generally accepted practice is to perform a production test at a higher voltage for some shorter period of time. The relationship between actual test conditions and the continuous derated maximum specification is an important one. Burr-Brown has chosen a deliberately conservative one: VDCTEST = (2 X VACrms CONTINUOUS RATING) + 1000V for ten seconds. This choice is appropriate for conditions where system transient voltages are not well defined.(1) Where the real voltages are well-defined or where the isolation voltage is not continuous, the user may choose a less conservative derating to establish a specification from the test voltage. NOTE: (1) Reference National Electrical Manufacturers Association (NEMA) Standards Parts ICS I-109 and ICS I-111. OUTPUT SYNC SIGNAL To allow synchronization of an ISO120 or ISO121 isolation amplifier, the PWS725A and PWS726A have an OUTPUT SYNC signal at pin 29. It should be connected as shown in Figure 5 to keep capacitive loading of pin 29 to a minimum. If output sync is not used, leave pin open. 4 PWS725A/726A 29 20kΩ 20pF Ext Osc Connection of ISO120 or ISO121 FIGURE 5. Synchronization with ISO120 or ISO121 Isolation Amplifier. ® PWS725A/726A 6