REF2025, REF2030, REF2033, REF2041
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
REF20xx Low-Drift, Low-Power, Dual-Output, VREF and VREF / 2 Voltage References
1 Features
3 Description
•
Applications with only a positive supply voltage often
require additional stable voltage in the middle of
the analog-to-digital converter (ADC) input range to
bias input bipolar signals. The REF20xx provides a
reference voltage (VREF) for the ADC and a second
highly-accurate voltage (VBIAS) that can be used to
bias the input bipolar signals.
•
•
•
•
•
•
•
•
•
2 Applications
Electricity meter
Analog input module
Analog output module
Servo drive control module
Circuit breaker (ACB, MCCB, VCB)
Clinical digital thermometer
Lab & field instrumentation
Battery test
Both the VREF and VBIAS voltages have the same
excellent specifications and can sink and source
current equally well. Very good long-term stability and
low noise levels make these devices ideally-suited for
high-precision industrial applications.
Device Information
PACKAGE (1)
PART NAME
REF20xx
(1)
Power
Supply
SOT-23 (5)
INA213
ISENSE
VOUT
ADC
REF
VIN-
For all available packages, see the orderable addendum at
the end of the datasheet.
0.03
VBIAS
0.02
0.01
0
-0.01
-0.02
VREF
-0.03
-0.04
VBIAS
1.5 V
VREF
3.0 V
-0.05
±75
EN
±50
±25
0
25
50
75
100
Temperature (ƒC)
REF2030
GND
2.90 mm × 1.60 mm
0.04
VIN+
RSHUNT
BODY SIZE (NOM)
0.05
LOAD
•
•
•
•
•
•
•
•
The REF20xx offers excellent temperature drift
(8 ppm/°C, maximum) and initial accuracy (0.05%)
on both the VREF and VBIAS outputs while operating
at a quiescent current less than 430 µA. In addition,
the VREF and VBIAS outputs track each other with
a precision of 6 ppm/°C (maximum) across the
temperature range of –40°C to 125°C. All these
features increase the precision of the signal chain and
decrease board space, while reducing the cost of the
system as compared to a discrete solution. Extremely
low dropout voltage of only 10 mV allows operation
from very low input voltages, which can be very useful
in battery-operated systems.
Output Voltage Accuracy (%)
•
Two outputs, VREF and VREF / 2, for convenient
use in single-supply systems
Excellent temperature drift performance:
– 8 ppm/°C (maximum) from –40°C to 125°C
High initial accuracy: ±0.05% (maximum)
VREF and VBIAS tracking overtemperature:
– 6 ppm/°C (maximum) from –40°C to 85°C
– 7 ppm/°C (maximum) from –40°C to 125°C
Microsize package: SOT23-5
Low dropout voltage: 10 mV
High output current: ±20 mA
Low quiescent current: 360 μA
Line regulation: 3 ppm/V
Load regulation: 8 ppm/mA
Matte-Sn version (REF2025AISDDCR) for
improved corrosion resistance in the Battelle Class
III and similar harsh environments
VIN
125
150
C001
VREF and VBIAS vs Temperature
Application Example
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
Table of Contents
1 Features............................................................................1
2 Applications..................................................................... 1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Device Comparison Table...............................................3
6 Pin Configuration and Functions...................................3
Pin Functions.................................................................... 3
7 Specifications.................................................................. 4
7.1 Absolute Maximum Ratings........................................ 4
7.2 ESD Ratings............................................................... 4
7.3 Recommended Operating Conditions.........................4
7.4 Thermal Information....................................................4
7.5 Electrical Characteristics.............................................5
7.6 Typical Characteristics................................................ 6
8 Parameter Measurement Information.......................... 13
8.1 Solder Heat Shift.......................................................13
8.2 Long-Term Stability................................................... 14
8.3 Thermal Hysteresis................................................... 15
8.4 Noise Performance................................................... 16
9 Detailed Description......................................................17
9.1 Overview................................................................... 17
9.2 Functional Block Diagram......................................... 17
9.3 Feature Description...................................................17
9.4 Device Functional Modes..........................................18
10 Applications and Implementation.............................. 19
10.1 Application Information........................................... 19
10.2 Typical Application.................................................. 20
11 Power-Supply Recommendations..............................25
12 Layout...........................................................................26
12.1 Layout Guidelines................................................... 26
12.2 Layout Example...................................................... 26
13 Device and Documentation Support..........................27
13.1 Documentation Support.......................................... 27
13.2 Receiving Notification of Documentation Updates..27
13.3 Support Resources................................................. 27
13.4 Trademarks............................................................. 27
13.5 Electrostatic Discharge Caution..............................27
13.6 Glossary..................................................................27
14 Mechanical, Packaging, and Orderable
Information.................................................................... 27
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (May 2018) to Revision E (January 2022)
Page
• Updated Applications section............................................................................................................................. 1
• Updated the numbering format for tables, figures, and cross-references throughout the document..................1
• Changed ESD Rating table: changed HBM rating from ±4000 V to ±2500 V.....................................................4
• Updated Long-term stability value...................................................................................................................... 5
• Added Long-Term Stability sub-section under Parameter Measurement Information section..........................14
Changes from Revision C (January 2017) to Revision D (May 2018)
Page
• Changed application information to include corrosion resistance advantages. ............................................... 19
Changes from Revision B (July 2014) to Revision C (January 2017)
Page
• Added I/O column to Pin Functions table .......................................................................................................... 3
• Added Storage temperature parameter to Absolute Maximum Ratings table (moved from ESD Ratings table)
............................................................................................................................................................................4
• Changed ESD Rating table: changed title, updated table format ...................................................................... 4
Changes from Revision A (June 2014) to Revision B (July 2014)
Page
• Changed device status to Production Data from Mixed Status ......................................................................... 1
• Deleted footnote 2 from Device Information table ............................................................................................. 1
• Deleted footnote from Device Comparison Table .............................................................................................. 3
• Added Thermal Information table....................................................................................................................... 4
Changes from Revision * (May 2014) to Revision A (June 2014)
Page
• Made changes to product preview data sheet.................................................................................................... 1
2
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
5 Device Comparison Table
PRODUCT
VREF
VBIAS
REF2025
2.5 V
1.25 V
REF2030
3.0 V
1.5 V
REF2033
3.3 V
1.65 V
REF2041
4.096 V
2.048 V
6 Pin Configuration and Functions
VBIAS
1
GND
2
EN
3
5
VREF
4
VIN
Figure 6-1. DDC Package SOT23-5 (Top View)
Pin Functions
PIN
I/O
DESCRIPTION
NO.
NAME
1
VBIAS
2
GND
—
3
EN
Input
Enable (EN ≥ VIN – 0.7 V, device enabled)
Input supply voltage
Output
4
VIN
Input
5
VREF
Output
Bias voltage output (VREF / 2)
Ground
Reference voltage output (VREF)
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
3
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
Input voltage
MIN
MAX
VIN
–0.3
6
EN
–0.3
VIN + 0.3
Operating
–55
150
Junction, Tj
Temperature
V
150
Storage, Tstg
(1)
UNIT
–65
°C
170
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress
ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
±2500
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
±1500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
VIN
(1)
Supply input voltage range (IL = 0 mA, TA = 25°C)
VREF +
NOM
MAX
0.02(1)
5.5
UNIT
V
See Figure 7-28 in Section 7.6 for minimum input voltage at different load currents and temperature
7.4 Thermal Information
REF20xx
THERMAL
METRIC(1)
DDC (SOT23)
UNIT
5 PINS
RθJA
Junction-to-ambient thermal resistance
193.6
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
40.2
°C/W
RθJB
Junction-to-board thermal resistance
34.5
°C/W
ψJT
Junction-to-top characterization parameter
0.9
°C/W
ψJB
Junction-to-board characterization parameter
34.3
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7.5 Electrical Characteristics
At TA = 25°C, IL = 0 mA, and VIN = 5 V, unless otherwise noted. Both VREF and VBIAS have the same specifications.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ACCURACY AND DRIFT
Output voltage accuracy
–0.05%
Output voltage temperature coefficient(1)
0.05%
±3
±8
±1.5
±6
±2
±7
VREF + 0.02 V ≤ VIN ≤ 5.5 V
3
35
Sourcing
0 mA ≤ IL ≤ 20 mA ,
VREF + 0.6 V ≤ VIN ≤ 5.5 V
8
20
Sinking
0 mA ≤ IL ≤ –20 mA,
VREF + 0.02 V ≤ VIN ≤ 5.5 V
8
20
360
430
VREF and VBIAS tracking over temperature(2)
–40°C ≤ TA ≤ 125°C
–40°C ≤ TA ≤ 85°C
–40°C ≤ TA ≤ 125°C
ppm/°C
ppm/°C
LINE AND LOAD REGULATION
ΔVO(ΔVI)
ΔVO(ΔIL)
Line regulation
Load regulation
ppm/V
ppm/mA
POWER SUPPLY
Active mode
ICC
Supply current
Shutdown mode
–40°C ≤ TA ≤ 125°C
460
3.3
–40°C ≤ TA ≤ 125°C
Device in active mode (EN = 1)
0
0.7
VIN – 0.7
VIN
10
Dropout voltage
IL = 20 mA
ISC
Short-circuit current
ton
Turn-on time
0.1% settling, CL = 1 µF
Low-frequency noise(3)
0.1 Hz ≤ f ≤ 10 Hz
Output voltage noise density
f = 100 Hz
µA
9
Device in shutdown mode (EN = 0)
Enable voltage
5
20
600
V
mV
50
mA
500
µs
NOISE
12
ppmPP
0.25
ppm/√ Hz
CAPACITIVE LOAD
Stable output capacitor range
0
10
µF
HYSTERESIS AND LONG TERM STABILITY
Long-term stability(4)
0 to 1000 hours
Output voltage hysteresis(5)
(1)
(2)
(3)
(4)
(5)
25°C, –40°C, 125°C, 25°C
25
Cycle 1
60
Cycle 2
35
ppm
ppm
Temperature drift is specified according to the box method. See the Section 9.3 section for more details.
The VREF and VBIAS tracking over temperature specification is explained in more detail in the Section 9.3 section.
The peak-to-peak noise measurement procedure is explained in more detail in the Section 8.4 section.
Long-term stability measurement procedure is explained in more in detail in the Section 8.2 section.
The thermal hysteresis measurement procedure is explained in more detail in the Section 8.3 section.
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
5
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7.6 Typical Characteristics
At TA = 25°C, IL = 0 mA, VIN = 5-V power supply, CL = 0 µF, and 2.5-V output, unless otherwise noted.
70
50
60
40
Population (%)
Population (%)
50
40
30
30
20
20
10
0
0.05
0.04
0.03
0.02
0.01
0
-0.01
-0.02
-0.03
-0.04
0
-0.05
10
VREF Initial Accuracy (%)
0
1
2
3
4
5
6
7
8
VREF Drift Distribution (ppm/ƒC)
C010
C015
Figure 7-1. Initial Accuracy Distribution (VREF)
–40°C ≤ TA ≤ 125°C
Figure 7-2. Drift Distribution (VREF)
50
80
70
40
Population (%)
Population (%)
60
50
40
30
20
30
20
10
0
0.05
0.04
0.03
0.02
0.01
0
-0.01
-0.02
-0.03
-0.04
0
-0.05
10
VBIAS Initial Accuracy (%)
0
1
2
3
4
5
6
7
8
VBIAS Drift Distribution (ppm/ƒC)
C015
C008
Figure 7-3. Initial Accuracy Distribution (VBIAS)
–40°C ≤ TA ≤ 125°C
Figure 7-4. Drift Distribution (VBIAS)
60
40
50
Population (%)
Population (%)
30
20
40
30
20
10
VREF and VBIAS Matching (ppm)
Figure 7-5. VREF – 2 × VBIAS Distribution
0
80
60
40
20
0
±20
±40
±60
±80
0
±100
10
0
1
2
3
4
5
6
VREF and VBIAS Tracking Over Temperature (ppm/ƒC)
C016
C004
–40°C ≤ TA ≤ 85°C
Figure 7-6. Distribution of VREF – 2 × VBIAS Drift Tracking Over
Temperature
6
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7.6 Typical Characteristics (continued)
At TA = 25°C, IL = 0 mA, VIN = 5-V power supply, CL = 0 µF, and 2.5-V output, unless otherwise noted.
60
50
40
40
Population (%)
Population (%)
50
30
20
30
20
10
10
0
0
1
2
3
4
5
6
0
7
-0.0125 -0.01 -0.0075 -0.005 -0.0025
VREF and VBIAS Tracking Over Temperature (ppm/ƒC)
0
0.0025
Solder Heat Shift Histogram - VREF (%)
C017
C041
–40°C ≤ TA ≤ 125°C
Refer to the Section 8.1 section for more information.
Figure 7-7. Distribution of VREF – 2 × VBIAS Drift Tracking Over
Temperature
Figure 7-8. Solder Heat Shift Distribution (VREF)
0.05
60
0.04
Output Voltage Accuracy (%)
Population (%)
50
40
30
20
10
0.03
VBIAS
0.02
0.01
0
-0.01
-0.02
VREF
-0.03
-0.04
0
-0.0125 -0.01 -0.0075 -0.005 -0.0025
0
-0.05
0.0025
±75
±50
±25
0
Solder Heat Shift Histogram - VBIAS (%)
25
50
75
100
125
Temperature (ƒC)
C040
Refer to the Section 8.1 section for more information.
150
C001
Figure 7-10. Output Voltage Accuracy (VREF) vs Temperature
Figure 7-9. Solder Heat Shift Distribution (VBIAS)
2.5005
1000
-40°C
2.5000
500
250
VREF (V)
VREF - 2 x VBIAS (ppm)
750
0
±250
2.4995
25°C
2.4990
125°C
±500
2.4985
±750
2.4980
±1000
±75
±50
±25
0
25
50
75
100
125
150
Temperature (ƒC)
±20
±15
±10
±5
0
5
10
Load Current (mA)
C003
15
20
C038
Figure 7-11. VREF – 2 × VBIAS Tracking vs Temperature
VREF output
Figure 7-12. Output Voltage Change vs Load Current (VREF)
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
7
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7.6 Typical Characteristics (continued)
1.2503
-40°C
VBIAS (V)
1.2501
1.2499
1.2497
25°C
125°C
1.2495
1.2493
±20
±15
±10
0
±5
5
10
15
Load Current (mA)
20
VREF - Load Regulation Sourcing (ppm/mA)
At TA = 25°C, IL = 0 mA, VIN = 5-V power supply, CL = 0 µF, and 2.5-V output, unless otherwise noted.
12
11
10
9
8
7
6
5
4
±75
10
9
8
7
6
5
4
0
25
50
75
100
125
Temperature (ƒC)
VBIAS output
150
100
125
150
C025
11
10
9
8
7
6
5
4
±75
±50
±25
0
25
50
75
100
125
Temperature (ƒC)
VREF output
150
C021
IL = –20 mA
Figure 7-16. Load Regulation Sinking vs Temperature (VREF)
5
12
11
VREF Line Regulation (ppm/V)
VBIAS - Load Regulation Sinking (ppm/mA)
75
12
IL = 20 mA
10
9
8
7
6
5
4.5
4
3.5
3
2.5
2
4
±75
±50
±25
0
25
50
75
Temperature (ƒC)
VBIAS output
100
125
150
Submit Document Feedback
±75
±50
±25
0
25
50
75
100
125
Temperature (ƒC)
C022
IL = –20 mA
Figure 7-17. Load Regulation Sinking vs Temperature (VBIAS)
8
50
IL = 20 mA
C020
Figure 7-15. Load Regulation Sourcing vs Temperature (VBIAS)
25
Figure 7-14. Load Regulation Sourcing vs Temperature (VREF)
VREF - Load Regulation Sinking (ppm/mA)
VBIAS - Load Regulation Sourcing (ppm/mA)
11
±25
0
VREF output
12
±50
±25
Temperature (ƒC)
VBIAS output
Figure 7-13. Output Voltage Change vs Load Current (VBIAS)
±75
±50
C039
150
C019
VREF output
Figure 7-18. Line Regulation vs Temperature (VREF)
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7.6 Typical Characteristics (continued)
At TA = 25°C, IL = 0 mA, VIN = 5-V power supply, CL = 0 µF, and 2.5-V output, unless otherwise noted.
100
4.5
VBIAS
80
4
PSRR (dB)
VBIAS Line Regulation (ppm/V)
5
3.5
VREF
60
3
40
2.5
20
2
±75
±50
±25
0
25
50
75
100
125
Temperature (ƒC)
1
150
10
100
1k
10k
100k
Frequency (Hz)
C018
C026
CL = 0 µF
VBIAS output
Figure 7-20. Power-Supply Rejection Ratio vs Frequency
Figure 7-19. Line Regulation vs Temperature (VBIAS)
100
VIN + 0.25 V
VBIAS
500 mV/div
PSRR (dB)
80
VIN + 0.25 V
VIN - 0.25 V
VREF
VREF
40 mV/div
60
40
20
1
10
100
1k
10k
Frequency (Hz)
Time (500 µs/div)
100k
C006
C027
CL = 1 µF
CL = 10 µF
Figure 7-22. Line Transient Response
Figure 7-21. Power-Supply Rejection Ratio vs Frequency
VIN + 0.25 V
500 mV/div
VIN + 0.25V
+1 mA
VIN - 0.25V
+1 mA
2 mA/div
- 1 mA
VREF
40 mV/div
VREF
20 mV/div
Time (500 µs/div)
Time (500 µs/div)
C006
CL = 10 µF
Figure 7-23. Line Transient Response
C032
CL = 1 µF
IL = ±1-mA step
Figure 7-24. Load Transient Response
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
9
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7.6 Typical Characteristics (continued)
At TA = 25°C, IL = 0 mA, VIN = 5-V power supply, CL = 0 µF, and 2.5-V output, unless otherwise noted.
+20 mA
+20 mA
+1 mA
+1 mA
40 mA/div
2 mA/div
-20 mA
- 1 mA
VREF
VREF
20 mV/div
40 mV/div
Time (500 µs/div)
Time (500 µs/div)
C037
CL = 10 µF
C031
IL = ±1-mA step
CL = 1 µF
Figure 7-25. Load Transient Response
IL = ±20-mA step
Figure 7-26. Load Transient Response
400
125°C
Dropout Voltage (mV)
+20 mA
+20 mA
40 mA/div
-20 mA
VREF
40 mV/div
300
25°C
±40°C
200
100
0
Time (500 µs/div)
±30
±20
±10
CL = 10 µF
0
10
Load Current (mA)
C036
20
30
C005
Figure 7-28. Minimum Dropout Voltage vs Load Current
IL = ±20-mA step
Figure 7-27. Load Transient Response
VIN
VIN
2 V/div
2 V/div
VREF
VREF
Time (100 µs/div)
Time (100 µs/div)
C034
C033
CL = 1 µF
Figure 7-29. Turn-On Settling Time
10
Submit Document Feedback
CL = 10 µF
Figure 7-30. Turn-On Settling Time
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7.6 Typical Characteristics (continued)
500
500
450
450
Quiescent Current ( A)
Quiescent Current ( A)
At TA = 25°C, IL = 0 mA, VIN = 5-V power supply, CL = 0 µF, and 2.5-V output, unless otherwise noted.
400
350
300
400
350
300
250
250
200
200
±75
±50
±25
0
25
50
75
100
125
2
150
Temperature (ƒC)
3
4
5
6
Input Voltage (V)
C006
C007
Figure 7-32. Quiescent Current vs Input Voltage
Voltage (5 V/div)
Voltage (5 V/div)
Figure 7-31. Quiescent Current vs Temperature
Time (1 s/div)
Time (1 s/div)
C028
C029
VREF output
VBIAS output
Figure 7-33. 0.1-Hz to 10-Hz Noise (VREF)
Figure 7-34. 0.1-Hz to 10-Hz Noise (VBIAS)
100
CL = 0 F
Output Impedance ( )
2XWSXW 1RLVH 6SHFWUDO 'HQVLW\ SSP ¥+]
1
CL = 0 µF
0.1
CL = 4.7 F
10
CL = 1µF
1
CL = 10 F
0.1
CL = 10 µF
0.01
1
10
100
1k
Frequency (Hz)
10k
0.01
0.01
0.1
1
10
100
1k
10k
Frequency (Hz)
C030
Figure 7-35. Output Voltage Noise Spectrum
100k
C024
VREF output
Figure 7-36. Output Impedance vs Frequency (VREF)
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
11
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
7.6 Typical Characteristics (continued)
At TA = 25°C, IL = 0 mA, VIN = 5-V power supply, CL = 0 µF, and 2.5-V output, unless otherwise noted.
100
40
Output Impedance ( )
CL = 0 F
35
30
Population (%)
10
CL = 1µF
1
CL = 10 F
25
20
15
10
0.1
10k
100k
Frequency (Hz)
Thermal Hysterisis - VREF (ppm)
C023
C013
VBIAS output
Figure 7-38. Thermal Hysteresis Distribution (VREF)
Figure 7-37. Output Impedance vs Frequency (VBIAS)
50
40
45
Output Voltage Stability (ppm)
35
Population (%)
30
25
20
15
10
5
40
35
30
25
20
15
10
5
0
-10
120
100
80
60
40
20
-5
0
0
120
1k
100
100
80
10
60
1
40
0.1
0
0
0.01
0.01
20
5
0
Thermal Hysteresis - VBIAS (ppm)
C014
100
200
300
400 500 600
Time (hr)
700
800
900 1000
Figure 7-40. Long-Term Stability (First 1000 hours)
Figure 7-39. Thermal Hysteresis Distribution (VBIAS)
12
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
8 Parameter Measurement Information
8.1 Solder Heat Shift
The materials used in the manufacture of the REF20xx have differing coefficients of thermal expansion, resulting
in stress on the device die when the part is heated. Mechanical and thermal stress on the device die can cause
the output voltages to shift, degrading the initial accuracy specifications of the product. Reflow soldering is a
common cause of this error.
In order to illustrate this effect, a total of 92 devices were soldered on four printed circuit boards [23 devices
on each printed circuit board (PCB)] using lead-free solder paste and the paste manufacturer suggested reflow
profile. The reflow profile is as shown in Figure 8-1. The printed circuit board is comprised of FR4 material. The
board thickness is 1.57 mm and the area is 171.54 mm × 165.1 mm.
The reference and bias output voltages are measured before and after the reflow process; the typical shift is
displayed in Figure 8-2 and Figure 8-3. Although all tested units exhibit very low shifts (< 0.01%), higher shifts
are also possible depending on the size, thickness, and material of the printed circuit board. An important note is
that the histograms display the typical shift for exposure to a single reflow profile. Exposure to multiple reflows,
as is common on PCBs with surface-mount components on both sides, causes additional shifts in the output bias
voltage. If the PCB is exposed to multiple reflows, the device should be soldered in the second pass to minimize
its exposure to thermal stress.
300
Temperature (ƒC)
250
200
150
100
50
0
0
50
100
150
200
250
300
Time (seconds)
350
400
C01
Figure 8-1. Reflow Profile
60
50
50
Population (%)
Population (%)
40
30
20
10
0
40
30
20
10
-0.0125 -0.01 -0.0075 -0.005 -0.0025
0
0.0025
Solder Heat Shift Histogram - VREF (%)
0
-0.0125 -0.01 -0.0075 -0.005 -0.0025
0
0.0025
Solder Heat Shift Histogram - VBIAS (%)
C041
C040
Figure 8-2. Solder Heat Shift Distribution, VREF (%) Figure 8-3. Solder Heat Shift Distribution, VBIAS (%)
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
13
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
8.2 Long-Term Stability
The long term stability of the REF20xx was collected on 32 parts that were soldered onto Printed Circuit
Boards without any slots or special layout considerations. The boards were then placed into an oven with air
temperature maintained at TA = 35°C. The VREF output of the 32 parts was measured regularly. Typical long term
stability is as shown in Figure 8-4.
50
Output Voltage Stability (ppm)
45
40
35
30
25
20
15
10
5
0
-5
-10
0
100
200
300
400 500 600
Time (hr)
700
800
900 1000
Figure 8-4. Long Term Stability – 1000 hours (VREF)
14
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
8.3 Thermal Hysteresis
Thermal hysteresis is measured with the REF20xx soldered to a PCB, similar to a real-world application.
Thermal hysteresis for the device is defined as the change in output voltage after operating the device at 25°C,
cycling the device through the specified temperature range, and returning to 25°C. Hysteresis can be expressed
by Equation 1:
§ VPRE VPOST
¨¨
VNOM
©
VHYST
·
6
¸¸ x 10
¹
(ppm)
(1)
where
•
•
•
•
VHYST = thermal hysteresis (in units of ppm),
VNOM = the specified output voltage,
VPRE = output voltage measured at 25°C pre-temperature cycling, and
VPOST = output voltage measured after the device has cycled from 25°C through the specified temperature
range of –40°C to 125°C and returns to 25°C.
40
35
35
30
30
Thermal Hysterisis - VREF (ppm)
120
100
120
100
0
80
5
0
60
5
40
10
20
10
80
15
60
15
20
40
20
25
20
25
0
Population (%)
40
0
Population (%)
Typical thermal hysteresis distribution is as shown in Figure 8-5 and Figure 8-6.
Thermal Hysteresis - VBIAS (ppm)
C013
Figure 8-5. Thermal Hysteresis Distribution (VREF)
C014
Figure 8-6. Thermal Hysteresis Distribution (VBIAS)
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
15
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
8.4 Noise Performance
Voltage (5 V/div)
Voltage (5 V/div)
Typical 0.1-Hz to 10-Hz voltage noise can be seen in Figure 8-7 and Figure 8-8. Device noise increases
with output voltage and operating temperature. Additional filtering can be used to improve output noise levels,
although care should be taken to ensure the output impedance does not degrade ac performance. Peak-to-peak
noise measurement setup is shown in Figure 8-9.
Time (1 s/div)
Time (1 s/div)
C028
C029
Figure 8-7. 0.1-Hz to 10-Hz Noise (VREF)
Figure 8-8. 0.1-Hz to 10-Hz Noise (VBIAS)
10 k
100
40 mF
VIN
To scope
VREF
REF20xx
0.1 F
GND
+
10 F
EN
1k
2-Pole High-pass
4-Pole Low-pass
0.1 Hz to 10 Hz Filter
VBIAS
Figure 8-9. 0.1-Hz to 10-Hz Noise Measurement Setup
16
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
9 Detailed Description
9.1 Overview
The REF20xx are a family of dual-output, VREF and VBIAS (VREF / 2) band-gap voltage references. The Section
9.2 section provides a block diagram of the basic band-gap topology and the two buffers used to derive the VREF
and VBIAS outputs. Transistors Q1 and Q2 are biased such that the current density of Q1 is greater than that of
Q2. The difference of the two base emitter voltages (VBE1 – VBE2) has a positive temperature coefficient and is
forced across resistor R5. The voltage is amplified and added to the base emitter voltage of Q2, which has a
negative temperature coefficient. The resulting band-gap output voltage is almost independent of temperature.
Two independent buffers are used to generate VREF and VBIAS from the band-gap voltage. The resistors R1, R2
and R3, R4 are sized such that VBIAS = VREF / 2.
e-Trim™ is a method of package-level trim for the initial accuracy and temperature coefficient of VREF and V BIAS,
implemented during the final steps of manufacturing after the plastic molding process. This method minimizes
the influence of inherent transistor mismatch, as well as errors induced during package molding. e-Trim is
implemented in the REF20xx to minimize the temperature drift and maximize the initial accuracy of both the VREF
and VBIAS outputs.
9.2 Functional Block Diagram
R2
R6
R1
R7
VREF
+
+
e-Trim
R5
+
VBE1
-
+
VBE2
-
R4
R3
Q2
Q1
VBIAS
e-Trim
+
9.3 Feature Description
9.3.1 VREF and VBIAS Tracking
Most single-supply systems require an additional stable voltage in the middle of the analog-to-digital converter
(ADC) input range to bias input bipolar signals. The VREF and VBIAS outputs of the REF20xx are generated from
the same band-gap voltage as shown in the Section 9.2 section. Hence, both outputs track each other over
the full temperature range of –40°C to 125°C with an accuracy of 7 ppm/°C (maximum). The tracking accuracy
increases to 6 ppm/°C (maximum) when the temperature range is limited to –40°C to 85°C. The tracking error is
calculated using the box method, as described by Equation 2:
Tracking Error
VDIFF(MAX) VDIFF (MIN)
§
·
6
¨
¸ x 10
x
V
Temperature
Range
© REF
¹
(ppm)
(2)
where
•
VDIFF
VREF
2 ‡ VBIAS
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
17
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
The tracking accuracy is as shown in Figure 9-1.
0.05
Output Voltage Accuracy (%)
0.04
0.03
VBIAS
0.02
0.01
0
-0.01
-0.02
VREF
-0.03
-0.04
-0.05
±75
±50
±25
0
25
50
75
Temperature (ƒC)
100
125
150
C001
Figure 9-1. VREF and VBIAS Tracking vs Temperature
9.3.2 Low Temperature Drift
The REF20xx is designed for minimal drift error, which is defined as the change in output voltage over
temperature. The drift is calculated using the box method, as described by Equation 3:
Drift
V REF(MAX) V REF(MIN)
§
·
6
¨
¸ x 10
© V REF xTemperature Range ¹
(ppm)
(3)
9.3.3 Load Current
The REF20xx family is specified to deliver a current load of ±20 mA per output. Both the VREF and VBIAS outputs
of the device are protected from short circuits by limiting the output short-circuit current to 50 mA. The device
temperature increases according to Equation 4:
TJ
TA
PD ‡ R
(4)
-$
where
•
•
•
•
TJ = junction temperature (°C),
TA = ambient temperature (°C),
PD = power dissipated (W), and
RθJA = junction-to-ambient thermal resistance (°C/W)
The REF20xx maximum junction temperature must not exceed the absolute maximum rating of 150°C.
9.4 Device Functional Modes
When the EN pin of the REF20xx is pulled high, the device is in active mode. The device should be in active
mode for normal operation. The REF20xx can be placed in a low-power mode by pulling the ENABLE pin low.
When in shutdown mode, the output of the device becomes high impedance and the quiescent current of the
device reduces to 5 µA in shutdown mode. See the Section 7.5 for logic high and logic low voltage levels.
18
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
10 Applications and Implementation
Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
10.1 Application Information
The low-drift, bidirectional, single-supply, low-side, current-sensing solution, described in this section, can
accurately detect load currents from –2.5 A to 2.5 A. The linear range of the output is from 250 mV to 2.75 V.
Positive current is represented by output voltages from 1.5 V to 2.75 V, whereas negative current is represented
by output voltages from 250 mV to 1.5 V. The difference amplifier is the INA213 current-shunt monitor, whose
supply and reference voltages are supplied by the low-drift REF2030.
Industrial applications with electronics in corrosive environments are susceptible to corrosive damage due to the
exposure to heat, moisture, and corrosive gases. The combination of the following conditions in a given system
lead to higher risk of corrosive damage:
1.
2.
3.
4.
Ventilated enclosures exposing underlying PCB.
PCBs not conformally coated.
Exposed-lead components with plating susceptible to corrosion.
Changes in plating techniques for RoHS compliance (e.g. removal of Pb (lead) and certain types of plating).
To improve resistance to corrosion in harsh environments, the REF2025AISDDCR uses Matte-Sn plating with
improved assembly process to reduce exposed Cu, leading to improved corrosion resistance in the Battelle
Class III and similar harsh environments. The “S” in the part number identifies this special plating option.
REF2025 versions that do not have the “S” will continue to be available in industry standard NiPdAu processing
technique.
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
19
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
10.2 Typical Application
10.2.1 Low-Side, Current-Sensing Application
REF20xx
VREF
+
VIN
Bandgap
EN
+
VCC
VBIAS
+
±
GND
REF
±ILOAD
VBUS
+
±
IN+
V+
VREF
+
OUT
ADC
RSHUNT
VOUT
INGND
INA213B
Figure 10-1. Low-Side, Current-Sensing Application
20
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
10.2.1.1 Design Requirements
The design requirements are as follows:
1. Supply voltage: 5.0 V
2. Load current: ±2.5 A
3. Output: 250 mV to 2.75 V
4. Maximum shunt voltage: ±25 mV
10.2.1.2 Detailed Design Procedure
Low-side current sensing is desirable because the common-mode voltage is near ground. Therefore, the currentsensing solution is independent of the bus voltage, VBUS. When sensing bidirectional currents, use a differential
amplifier with a reference pin. This procedure allows for the differentiation between positive and negative
currents by biasing the output stage such that it can respond to negative input voltages. There are a variety of
methods for supplying power (V+) and the reference voltage (VREF, or VBIAS) to the differential amplifier. For a
low-drift solution, use a monolithic reference that supplies both power and the reference voltage. Figure 10-2
shows the general circuit topology for a low-drift, low-side, bidirectional, current-sensing solution. This topology
is particularly useful when interfacing with an ADC; see Figure 10-1. Not only do VREF and VBIAS track over
temperature, but their matching is much better than alternate topologies. For a more detailed version of the
design procedure, refer to TIDU357.
REF20xx
VREF
+
VIN
Bandgap
EN
+
VCC
VBIAS
+
±
GND
REF
±ILOAD
VBUS
+
±
IN+
± VSHUNT
V+
+
RSHUNT
OUT
VOUT
INGND
INA213B
Figure 10-2. Low-Drift, Low-side, Bidirectional, Current-Sensing Circuit Topology
The transfer function for the circuit given in Figure 10-2 is as shown in Equation 5:
VOUT
G ‡ r VSHUNT
VBIAS
G ‡ rILOAD ‡ RSHUNT
VBIAS
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
(5)
Submit Document Feedback
21
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
10.2.1.2.1 Shunt Resistor
As illustrated in Figure 10-2, the value of VSHUNT is the ground potential for the system load. If the value of
VSHUNT is too large, issues may arise when interfacing with systems whose ground potential is actually 0 V. Also,
a value of VSHUNT that is too negative may violate the input common-mode voltage of the differential amplifier
in addition to potential interfacing issues. Therefore, limiting the voltage across the shunt resistor is important.
Equation 6 can be used to calculate the maximum value of RSHUNT.
R SHUNT(max)
VSHUNT(max)
I LOAD(max)
(6)
Given that the maximum shunt voltage is ±25 mV and the load current range is ±2.5 A, the maximum shunt
resistance is calculated as shown in Equation 7.
R SHUNT (max)
VSHUNT (max)
I LOAD (max)
25mV
10m:
2.5A
(7)
To minimize errors over temperature, select a low-drift shunt resistor. To minimize offset error, select a shunt
resistor with the lowest tolerance. For this design, the Y14870R01000B9W resistor is used.
10.2.1.2.2 Differential Amplifier
The differential amplifier used for this design should have the following features:
1. Single-supply (3 V),
2. Reference voltage input,
3. Low initial input offset voltage (VOS),
4. Low-drift,
5. Fixed gain, and
6. Low-side sensing (input common-mode range below ground).
For this design, a current-shunt monitor (INA213) is used. The INA21x family topology is shown in Figure 10-3.
The INA213B specifications can be found in the INA213 product data sheet.
V+
IN-
OUT
IN+
+
REF
GND
Copyright © 2017, Texas Instruments Incorporated
Figure 10-3. INA21x Current-Shunt Monitor Topology
The INA213B is an excellent choice for this application because all the required features are included. In
general, instrumentation amplifiers (INAs) do not have the input common-mode swing to ground that is essential
for this application. In addition, INAs require external resistors to set their gain, which is not desirable for low-drift
applications. Difference amplifiers typically have larger input bias currents, which reduce solution accuracy at
22
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
small load currents. Difference amplifiers typically have a gain of 1 V/V. When the gain is adjustable, these
amplifiers use external resistors that are not conducive to low-drift applications.
10.2.1.2.3 Voltage Reference
The voltage reference for this application should have the following features:
1. Dual output (3.0 V and 1.5 V),
2. Low drift, and
3. Low tracking errors between the two outputs.
For this design, the REF2030 is used. The REF20xx topology is as shown in the Section 9.2 section.
The REF2030 is an excellent choice for this application because of its dual output. The temperature drift of
8 ppm/°C and initial accuracy of 0.05% make the errors resulting from the voltage reference minimal in this
application. In addition, there is minimal mismatch between the two outputs and both outputs track very well
across temperature, as shown in Figure 10-4 and Figure 10-5.
60
40
50
Population (%)
Population (%)
30
20
40
30
20
10
VREF and VBIAS Matching (ppm)
0
80
60
40
20
0
±20
±40
±60
±80
0
±100
10
0
1
2
3
4
5
6
VREF and VBIAS Tracking Over Temperature (ppm/ƒC)
C016
C004
Figure 10-4. VREF – 2 × VBIAS Distribution (At TA =
25°C)
Figure 10-5. Distribution of VREF – 2 × VBIAS Drift
Tracking Over Temperature
10.2.1.2.4 Results
Table 10-1 summarizes the measured results.
Table 10-1. Measured Results
ERROR
UNCALIBRATED (%)
CALIBRATED (%)
Error across the full load current range (25°C)
±0.0355
±0.004
Error across the full load current range (–40°C to 125°C)
±0.0522
±0.0606
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
23
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
10.2.1.3 Application Curves
Performing a two-point calibration at 25°C removes the errors associated with offset voltage, gain error, and so
forth. Figure 10-6 to Figure 10-8 show the measured error at different conditions. For a more detailed description
on measurement procedure, calibration, and calculations, please refer to TIDU357.
3
800
Uncalibrated error (ppm)
Output Voltage (Vout)
-40°C
600
2.5
2
1.5
1
0.5
400
0°C
200
0
25°C
85°C
±200
±400
±600
0
125°C
±800
-3
-2
-1
0
1
2
Load current (mA)
3
±3
±2
±1
0
Load current (mA)
C00
Figure 10-6. Measured Transfer Function
1
2
3
C00
Figure 10-7. Uncalibrated Error vs Load Current
800
-40°C
Calibrated error (ppm)
600
400
0°C
200
0
25°C
85°C
±200
±400
±600
125°C
±800
±3
±2
±1
0
Load current (mA)
1
2
3
C00
Figure 10-8. Calibrated Error vs Load Current
24
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
11 Power-Supply Recommendations
The REF20xx family of references feature an extremely low-dropout voltage. These references can be operated
with a supply of only 20 mV above the output voltage. For loaded reference conditions, a typical dropout
voltage versus load is shown in Figure 11-1. A supply bypass capacitor ranging between 0.1 µF to 10 µF is
recommended.
400
Dropout Voltage (mV)
125°C
300
25°C
±40°C
200
100
0
±30
±20
±10
0
10
Load Current (mA)
20
30
C005
Figure 11-1. Dropout Voltage vs Load Current
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
25
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
12 Layout
12.1 Layout Guidelines
Figure 12-1 shows an example of a PCB layout for a data acquisition system using the REF2030. Some key
considerations are:
• Connect low-ESR, 0.1-μF ceramic bypass capacitors at VIN, VREF, and VBIAS of the REF2030.
• Decouple other active devices in the system per the device specifications.
• Using a solid ground plane helps distribute heat and reduces electromagnetic interference (EMI) noise
pickup.
• Place the external components as close to the device as possible. This configuration prevents parasitic errors
(such as the Seebeck effect) from occurring.
• Minimize trace length between the reference and bias connections to the INA and ADC to reduce noise
pickup.
• Do not run sensitive analog traces in parallel with digital traces. Avoid crossing digital and analog traces if
possible, and only make perpendicular crossings when absolutely necessary.
INOUT
Analog Input
Via
to GND
Plane
V+
Via to
Input Power
C
GND
C
REF
VBIAS
C
GND
EN
REF20xx
IN+
INA213
12.2 Layout Example
REF
VREF
C
Microcontroller
A/D Input
C
VIN
DIG1
AIN
Figure 12-1. Layout Example
26
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
REF2025, REF2030, REF2033, REF2041
www.ti.com
SBOS600E – JULY 2018 – REVISED FEBRUARY 2022
13 Device and Documentation Support
13.1 Documentation Support
13.1.1 Related Documentation
For related documentation see the following:
•
•
INA21x Voltage Output, Low- or High-Side Measurement, Bidirectional, Zero-Drift Series, Current-Shunt
Monitors (SBOS437)
Low-Drift Bidirectional Single-Supply Low-Side Current Sensing Reference Design (TIDU357)
13.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
13.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
13.4 Trademarks
e-Trim™ is a trademark of Texas Instruments, Inc.
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
13.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
13.6 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: REF2025 REF2030 REF2033 REF2041
Submit Document Feedback
27
PACKAGE OPTION ADDENDUM
www.ti.com
9-Mar-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
REF2025AIDDCR
ACTIVE
SOT-23-THIN
DDC
5
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
GACM
REF2025AIDDCT
ACTIVE
SOT-23-THIN
DDC
5
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
GACM
REF2025AISDDCR
ACTIVE
SOT-23-THIN
DDC
5
3000
RoHS & Green
Call TI
Level-2-260C-1 YEAR
-40 to 125
1M98
REF2030AIDDCR
ACTIVE
SOT-23-THIN
DDC
5
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
GADM
REF2030AIDDCT
ACTIVE
SOT-23-THIN
DDC
5
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
GADM
REF2033AIDDCR
ACTIVE
SOT-23-THIN
DDC
5
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
GAEM
REF2033AIDDCT
ACTIVE
SOT-23-THIN
DDC
5
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
GAEM
REF2041AIDDCR
ACTIVE
SOT-23-THIN
DDC
5
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
GAFM
REF2041AIDDCT
ACTIVE
SOT-23-THIN
DDC
5
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
GAFM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of