SCAN90CP02EVK/NOPB

SCAN90CP02 2x2 LVDS Cross-point Switch Evaluation Kit (RoHS Compliant) Documentation Rev2.3 November 07, 2006 Introduction National Semiconductor’s System Test Access Products Group provides this evaluation kit of the SCAN90CP02 to help demonstrate the use and performance of the device. The user must supply 3.3-volt power to the Evaluation board. The user also must provide the proper LVDS signal levels to the inputs of the device using a signal generator. Overview This Evaluation board uses two SCAN90CP02 devices. Device U1 uses SMA connectors for both the non-inverting and inverting differential input and output signals for each channel (total of 8 SMA connectors for U1). This enables the use of high speed signals for evaluating the performance of the LVDS signal path. Inputs are terminated with 100Ω. Device U2 may be used for both high speed LVDS evaluations and IEEE 1149.6 evaluations. Channel 0 of device U2 uses CAT5 connectors for the input and output signals to allow the use of “lossy” or inexpensive CAT5 cables as the interconnect medium. Inputs are terminated with 100Ω. Channel 1 of device U2 is used primarily for IEEE 1149.6 evaluations. The output of Channel 1 is looped back to the inputs of Channel 1 through a fault network. Thus, the fault network may be exercised while monitoring the effects through the IEEE 1149.1 port at J1. Switches S1 thru S5 are used to insert faults for evaluating the IEEE 1149.6 features (refer to the table 2 and figure 2 below). Additionally, U2 may be configured as a switch, and a high speed signal may be passed thru the fault network. This enables the evaluation of interconnect faults on the LVDS signal integrity. Switches S6 thru S11 are used as control inputs for both U1 and U2. Switches are provided for the SELx inputs, for the Enable inputs, and the PEMxx inputs to define the output pre-emphasis levels (refer to table 1 and figure 1 below). For more details, refer to the attached schematic and the SCAN90CP02 datasheet. Table 1: Control Switch Functions (applies to both U1 and U2) Silkscreen S11 DISABLE 0 S8 DISABLE 1 J7 S10 Sel0 S9 Sel1 Connections U1, U2 EN0* U1 EN1* U2 EN1* U1, U2 Sel0 U1, U2 Sel1 S7 PEMX0 S6 PEMX1 U1, U2 PEM00-PEM10 U1, U2 PEM01-PEM11 Notes Up position disables channel 0 on both devices. Up position disables channel 1 on U1. Open position disables channel 1 on U2. Configures both U1 and U2 functionality. Up = 1 down = 0 See datasheet for function table. Configures pre-emphasis feature on both devices and both channels. Up =1 Down = 0 See datasheet for function table. Figure 1: U1 Block Diagram Figure 2: U2 Block Diagram Table 2: IEEE-1149.1 and IEEE-1149.6 (applies only to U2) Silkscreen J1 1149.6 Function IEEE 1149.1 test bus access to 1149.6 features S1 S2 S3 S4 S5 Short C1 Short C2 Open Open Open Termination Resistor Notes U1 is the first device in the scan chain; U2 is the last device in the scan chain. TDO, TMS, TCK, /TRST (out) are from the test system to the device/chain under test. TDI (in) is from the device/chain under test to the test system. Up position to short coupling capacitor. Up position to short coupling capacitor. Down position to create open circuit. Down position to create open circuit at termination resistor. Down position to create open circuit. Note: This document is considered uncontrolled unless stamped otherwise. ENERCON - BILL OF MATERIALS TITLE: Main Product: NATIONAL SEMICONDUCTOR PCBA, SCAN90CP02EVK EVAL, ROHS PCBA, JTAG SCANCP02 EVAL, ROHS Item Part Type 1 PCB Part Number/Value Mfg P-05399R0 NoSub Description PL Number: Rev: Rev By: Z3015-01 2 AF Rev Date: PL Status: 10/26/2006 Released Responsible Eng/Mgr: Creator: Creation Date: Ed Ballou Arlene Fox 10/2/2006 Qty SCAN09CP02 EVAL ROHS: 3.50x3.50x.062in, 4 layer 1 Ref Des SMT Notes Rev Bd: (88.90x 88.90mm) Panel: (5.50x10.50in) (139.70x 266.70mm) 3 bds/panel 0 CUSTOMER SUPPLIED 1 2 3 IC SCAN90CP02SP NAT 1.5 GBPS LVDS Crosspoint Switch, LLP28 2 X U1-2 ERJ-3EKF3321 PANA 3.32K 1/10W ±1% 0603, Pb-Free 1 X R5 0 CRCW06033K32FKEA VISHAY 3.32K 1/10W ±1% 0603 100ppm, Pb-Free RK73H1JTTD3321F KOA 3.32K 1/10W ±1% 0603 100ppm, Pb-Free ERJ-3EKF49R9V PANA 49.9 Ohm 1/10W ±1% 0603 100ppm, Pb-Free 2 X R3,4 0 CRCW060349R9FKEA VISHAY 49.9 Ohm 1/10W ±1% 0603 100ppm RK73H1JTTD49R9F KOA 49.9 Ohm 1/10W ±1% 0603 100ppm, Pb-Free ERJ-2RKF1000 PANA 100 Ohm 1/16W ±1% 0402 100ppm, Pb-Free 3 X R1,2,6 2 ERJ-S02F1000 PANA 100 Ohm 1/16W ±1% 0402 200ppm, Pb-Free 06035A102KAT AVX 1000pF, 50V, ±10%, 0603, Ceramic, NP0, Pb-Free 3 X C1-2,4 0 C0603C102J5GAC KEMET 1000pF, 50V, ±5%, 0603, Ceramic, NP0, Pb-Free 06035C103KAT AVX .01µF, 50V, ±10%, 0603, Ceramic, X7R, Pb-Free 11 X C3,11-14,16,2123,25-26 Mount On Bottom C1114,16,21,22,23,2 5,26 0 C0603C103K5RAC KEMET .01µF, 50V, ±10%, 0603, Ceramic, X7R, Pb-Free 0603YC104KAT AVX .1µF, 16V, ±10%, 0603, Ceramic, X7R, PbFree 11 X C5,8-10,15,1720,24,27 Mount on Bottom C8-10,15,1720,24,27 0 4 5 RES 6 RES 7 RES 8 9 CAP 10 CAP 11 CAP 3:35:53 PM, 11/7/2006 Confidential and Proprietary. This document is considered uncontrolled unless stamped otherwise. Page 1 of 3 ENERCON - BILL OF MATERIALS TITLE: Main Product: NATIONAL SEMICONDUCTOR PCBA, SCAN90CP02EVK EVAL, ROHS PCBA, JTAG SCANCP02 EVAL, ROHS Item Part Type Part Number/Value Mfg NoSub Description PL Number: Rev: Rev By: Z3015-01 2 AF Rev Date: PL Status: 10/26/2006 Released Responsible Eng/Mgr: Creator: Creation Date: Ed Ballou Arlene Fox 10/2/2006 Qty Ref Des SMT Notes Rev C0603C104K4RAC KEMET .1µF, 16V, ±10%, 0603, Ceramic, X7R, PbFree TAJB106M010 AVX 10µF, 10V, ±20%, B-Case, Tantalum, PbFree T491B106K010AT KEMET 10µF, 10V, ±10%, B-Case, Tantalum, PbFree EG1249 ESWITCH Slide, SPDT, Pb-Free 16 CONN 5103309-1 AMP Header, 10p, Male, Dual Row, .100"sp, Pb-Free 1 J1 0 17 CONN 142-0711-821 JOH SMA, 50 0hm, End Launch, Pb-Free 8 J3-6,12-15 0 18 CONN 2560SU00001 LEOCO Shunt, .100"sp, Pb-Free 1 J7 0 71363-202LF FCI Shunt, .100"sp, Gold, Pb-Free SNT-100-BK-G SAMTEC Shunt, .100"sp, Gold, Pb-Free SNT-100-BK-H SAMTEC Shunt, .100"sp, Gold, Pb-Free 19 CONN 7006 KEYSTONE Binding Post, Red, Pb-Free 1 J10 0 20 CONN 7007 KEYSTONE Binding Post, Black, Pb-Free 1 J11 0 21 CONN 85505-0013 MOLEX Telco, 8p, R/A, Shielded, CAT5, Pb-Free 2 J8-9 0 22 CONN TSW-101-07-G-S SAMTEC Header, 1p, Male, Gold, Pb-Free 1 TP1 0 23 CONN TSW-102-07-G-S SAMTEC Header, 2p, Male, .100"sp, Gold, Pb-Free 1 J7 0 25 HDWRE 0700440LN MP Hex Nut, 4-40 Nylon Locking. Pb Free 4 26 HDWRE 36440MF075 MP Standoff, Male/Female, Hex, 440x3/16, Nylon, Pb Fr 4 Mount On Bottom 0 27 HDWRE 6INTLKWSSSROHS ANY Washer, #6 Internal Tooth, SS, ROHS 2 Use With Binding Posts 0 12 CAP 2 X C6-7 0 13 14 SW 11 S1-11 Remove Mounting Tabs Prior to Assembly 0 15 24 0 28 3:35:53 PM, 11/7/2006 Confidential and Proprietary. This document is considered uncontrolled unless stamped otherwise. Page 2 of 3 ENERCON - BILL OF MATERIALS TITLE: Main Product: NATIONAL SEMICONDUCTOR PCBA, SCAN90CP02EVK EVAL, ROHS PCBA, JTAG SCANCP02 EVAL, ROHS Item Part Type Part Number/Value Mfg NoSub Description PL Number: Rev: Rev By: Z3015-01 2 AF Rev Date: PL Status: 10/26/2006 Released Responsible Eng/Mgr: Creator: Creation Date: Ed Ballou Arlene Fox 10/2/2006 Qty SMT Ref Des Notes Rev 29 STENCL T-05401R0 ENERCON STENCIL FABRICATION, CP02 EVAL BOARD, ROHS, TOP 30 STENCL T-05404R0 ENERCON STENCIL FABRICATION, CP02 EVAL BOARD, ROHS, BOTTOM 1 31 REF C-05406R0 ENERCON PALLET DWG, CP02 EVAL BOARD, ROHS 0 32 REF C-05400R0 ENERCON FABRICATION DWG, CP02 EVAL BOARD, ROHS 0 33 REF S-03832R3 ENERCON SCHEMATIC, SCAN90CP02 EVAL BOARD 0 1 1 34 3:35:53 PM, 11/7/2006 Confidential and Proprietary. This document is considered uncontrolled unless stamped otherwise. Page 3 of 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated