SERDES24-35OVT
Evaluation Kit for OV7710 Image Sensor
Application with a FPD-Link II
(DS90C241/DS90C124) Serial Interface
SERDES24-35OVT
Rev 0.2
Description:
The SERDES24-35OVT is an evaluation kit designed to demonstrate
performance and capabilities of the DS90C124 and DS90C241 FPD-Link II
Serializer/Deserializer Chipset for use with the OmniVision “CLOTHO”
development system that features the OV7710 640 x 480 Color Image Sensor.
This serves as an add-on to the OmniVision development system, providing a
serialized digital interface between camera and controller.
The DS90C241 Serializer board accepts LVCMOS input signals from the Image
Sensor and provides single serialized FPD-Link II LVDS data pair as an output.
The DS90C124 Deserializer board accepts the FPD-Link II LVDS serialized data
stream and converts the data back into parallel LVCMOS signals and clock that
connects to the OmniVision USB Host Board.
Contents:
•
•
One DS90C241 Serializer board
One DS90C124 Deserializer board
What the user needs to provide:
•
•
•
•
•
OmniVision OV7710 Demo Board
OmniVision USB Board
CAT5 cable
External 5V power supply
PC with USB interface and Omnivision software (or alternate control
interface)
SER
DES
5V
OVT USB
Board
OVT
Imager
Figure 1. Imager - Serializer and Deserializer - Controller Connections
Setup instructions:
1. Connect the DS90C241 Serializer board to the Omnivision OV7710 Demo
Board. Refer to Figure 1.
SERDES24-35OVT
Rev 0.2
2. Connect the DS90C124 Deserializer board to the OmniVision USB Board.
Refer to Figure 1.
3. Connect the DS90C241 Serializer board to the DS90C124 Deserializer
board via the CAT5 cable.
4. Connect 5V power to the Deserializer board
5. Push “ON” button (S2) on Deserializer board. Green light should now be
visible on RJ45 connectors at Serializer (J3) board and Deserializer (J6)
board.
6. Connect PC/Controller to the Deserializer board via USB cable. Green
light should be visible on USB controller board (D2).
7. Launch Omnivision software (or alternate control application)
Troubleshooting:
Problem…
No image
No green light on RJ45 connectors
No green light on USB board
All lights on, but no image
No image
SERDES24-35OVT
Solution…
Check that all RJ45 and USB green
lights are on
Check that 5V power supply is
provided, and CAT cable connection
is good
Cycle “ON” button on deserializer
board
Check that USB is connected to PC
Check that orientation of board
connections is correct
Check that lens cap is removed from
camera
Rev 0.2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
SERDES24-35OVT/NOPB 价格&库存
很抱歉,暂时无法提供与“SERDES24-35OVT/NOPB”相匹配的价格&库存,您可以联系我们找货
免费人工找货