SmartRF06 Evaluation Board (EVM)
User's Guide
Literature Number: SWRU321B
May 2012 – Revised March 2017
Contents
1
2
Introduction ......................................................................................................................... 5
About This Manual ............................................................................................................... 5
2.1
3
Getting Started .................................................................................................................... 6
3.1
4
Installing SmartRF Studio and USB Drivers .......................................................................... 6
Using the SmartRF06 Evaluation Board .................................................................................. 9
4.1
5
Acronyms .................................................................................................................. 6
Absolute Maximum Ratings ........................................................................................... 10
SmartRF06 Evaluation Board Overview ................................................................................. 11
5.1
XDS100v3 Emulator.................................................................................................... 13
5.2
Power Sources .......................................................................................................... 13
5.3
Power Domains ......................................................................................................... 15
5.4
LCD ....................................................................................................................... 17
5.5
Micro SD Card Slot ..................................................................................................... 17
5.6
Accelerometer ........................................................................................................... 18
5.7
Ambient Light Sensor .................................................................................................. 18
5.8
Buttons ................................................................................................................... 19
5.9
LEDs...................................................................................................................... 19
5.10
EVM Connectors ........................................................................................................ 19
5.11
Breakout Headers and Jumpers ...................................................................................... 22
.................................................................................................
...............................................................
6.1
20-Pin ARM JTAG Header ............................................................................................
6.2
10-Pin ARM Cortex Debug Header ..................................................................................
6.3
Custom Strapping.......................................................................................................
7
Frequently Asked Questions ................................................................................................
8
References ........................................................................................................................
Appendix A Schematics ..............................................................................................................
A.1
SmartRF06EB 1.2.1 ...................................................................................................
Revision History ..........................................................................................................................
5.12
6
2
Current Measurement
Debugging an External Target Using SmartRF06EB
Table of Contents
25
27
28
28
29
30
30
31
31
37
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
www.ti.com
List of Figures
1
Driver Install: Update Driver ................................................................................................ 7
2
Driver Install: Specify Path to FTDI Drivers .............................................................................. 7
3
Driver Install: VCP Loaded ................................................................................................. 8
4
Driver Install: Drivers Successfully Installed
5
SmartRF06EB (rev. 1.2.1) With EVM Connected ....................................................................... 9
6
SmartRF06EB Architecture ............................................................................................... 11
7
SmartRF06EB Revision 1.2.1 Front Side ............................................................................... 12
8
SmartRF06EB Revision 1.2.1 Reverse Side
12
9
Jumper Mounted on J5 to Enable the UART Back Channel
13
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
.............................................................................
...........................................................................
.........................................................
Main Power Switch (P501) ................................................................................................
Source Selection Switch (P502) ..........................................................................................
SmartRF06EB Power Selection Switch (P502) in “USB” Position ...................................................
SmartRF06EB Power Source Selection Switch (P502) in “BAT” Position ..........................................
SmartRF06EB External Power Supply Header (J501) ................................................................
Power Domain Overview of SmartRF06EB .............................................................................
Mount a Jumper on J502 to Bypass EVM Domain Voltage Regulator ..............................................
Simplified Schematic of Ambient Light Sensor Setup .................................................................
SmartRF06EB EVM Connectors RF1 and RF2 ........................................................................
SmartRF06EB I/O Breakout Overview ..................................................................................
XDS100v3 Emulator Bypass Header (P408) ...........................................................................
20-Pin ARM JTAG Header (P409) .......................................................................................
10-Pin ARM Cortex Debug Header (P410) .............................................................................
Measuring Current Consumption Using Jumper J503 ................................................................
Measuring Current Consumption Using Jumper J503 ................................................................
Simplified Connection Diagram for Different Debugging Scenarios .................................................
Debugging External Target Using SmartRF06EB......................................................................
ARM JTAG Header (P409) With Strapping to Debug External Target ..............................................
SmartRF06EB - Top Level ................................................................................................
SmartRF06EB - XDS100v3 - FPGA .....................................................................................
SmartRF06EB - XDS100v3 - FTDI ......................................................................................
SmartRF06EB - EVM Interfaces/Level Shifters ........................................................................
SmartRF06EB - Power Supply ...........................................................................................
SmartRF06EB - High Voltage Peripheral ...............................................................................
SmartRF06EB - Low Voltage Peripherals ..............................................................................
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
List of Figures
8
14
14
14
14
15
15
16
18
19
22
24
24
25
26
26
27
28
29
31
32
33
34
35
36
36
3
www.ti.com
List of Tables
SmartRF06EB Features
2
Acronyms ..................................................................................................................... 6
3
Supply Voltage: Recommended Operating Conditions and Absolute Maximum Ratings
4
Temperature: Recommended Operating Conditions and Storage Temperatures ................................. 10
5
UART Back Channel Signal Connections ............................................................................... 13
6
Power Domain Overview of SmartRF06EB ............................................................................. 16
7
LCD Signal Connections .................................................................................................. 17
8
Micro SD Card Signal Connections ...................................................................................... 17
9
Accelerometer Signal Connections ...................................................................................... 18
10
Ambient Light Sensor Signal Connections .............................................................................. 18
11
Button Signal Connections ................................................................................................ 19
12
General Purpose LED Signal Connections ............................................................................. 19
13
EVM connector RF1 Pin Out
14
EVM Connector RF2 Pin Out
15
16
17
18
19
4
....................................................................................................
1
........................
.............................................................................................
............................................................................................
SmartRF06EB I/O Breakout Overview ..................................................................................
20-Pin ARM JTAG Header Pin-Out (P409) .............................................................................
10-Pin ARM Cortex Debug Header Pin-Out (P410) ...................................................................
Debugging External Target: Minimum Strapping (cJTAG support) ..................................................
Debugging External Target: Optional Strapping .......................................................................
List of Tables
5
10
20
21
23
24
25
29
29
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
User's Guide
SWRU321B – May 2012 – Revised March 2017
SmartRF06 Evaluation Board (EVM)
1
Introduction
The SmartRF06 Evaluation Board (SmartRF06EB or simply EB) is the motherboard in development kits
for Low Power RF ARM® Cortex®-M based System-on-Chips from Texas Instruments. The board has a
wide range of features, shown in Table 1.
Table 1. SmartRF06EB Features
2
Component
Description
TI XDS100v3 emulator
cJTAG and JTAG emulator for easy programming and debugging of SoCs on Evaluation
Modules (EVM) or external targets.
High-speed USB 2.0 interface
Easy plug and play access to full SoC control using SmartRF™ Studio PC software. Integrated
serial port over USB enables communication between the SoC via the UART back channel.
64x128 pixels serial LCD
Big LCD display for demo use and user interface development.
LEDs
Four general purpose LEDs for demo use or debugging.
Micro SD card slot
External flash for extra storage, over-the-air upgrades and more.
Buttons
Five push-buttons for demo use and user interfacing.
Accelerometer
Three-axis highly configurable digital accelerometer for application development and demo use.
Light sensor
Ambient light sensor for application development and demo use.
Breakout pins
Easy access to SoC GPIO pins for quick and easy debugging.
About This Manual
This manual contains reference information about the SmartRF06EB.
Section 3 will give a quick introduction on how to get started with the SmartRF06EB. It describes how to
install the SmartRF Studio software to get the required USB drivers for the evaluation board. Section 4
briefly explains how the EB can be used throughout a project’s development cycle. Section 5 gives an
overview of the various features and functionality provided by the board.
A troubleshooting guide is found in Section 7 and Appendix A contains the schematics for SmartRF06EB
revision 1.2.1.
The PC tools SmartRF Studio and SmartRF Flash Programmer have their own user manual.
For references to relevant documents and web pages, see Section 8.
SmartRF is a trademark of Texas Instruments.
ARM, Cortex are registered trademarks of ARM Limited.
All other trademarks are the property of their respective owners.
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
5
About This Manual
2.1
www.ti.com
Acronyms
Table 2. Acronyms
Acronym
ALS
cJTAG
Ambient Light Sensor
Compact JTAG (IEEE 1149.7)
CW
Continuous Wave
DK
Development Kit
EB
Evaluation Board
EVM
Evaluation Module
FPGA
Field-Programmable Gate Array
I/O
Input/Output
JTAG
Joint Test Action Group (IEEE 1149.1)
LCD
Liquid Crystal Display
LED
Light Emitting Diode
LPRF
Low Power RF
MCU
Microcontroller
MISO
Master In, Slave Out (SPI signal)
MOSI
Master Out, Slave In (SPI signal)
NA
Not Applicable / Not Available
NC
Not Connected
RF
Radio Frequency
RTS
Request to Send
RX
Receive
SoC
System-on-Chip
SPI
Serial Peripheral Interface
TI
Texas Instruments
TP
Test Point
TX
Transmit
UART
3
Description
Universal Asynchronous Receive Transmit
USB
Universal Serial Bus
VCP
Virtual COM Port
Getting Started
Before connecting the SmartRF06EB to the PC via the USB cable, it is highly recommended to perform
the steps described below.
3.1
Installing SmartRF Studio and USB Drivers
Before your PC can communicate with the SmartRF06EB over USB, the USB drivers for the EB needs to
be installed. The latest SmartRF Studio installer [1] includes USB drivers both for Windows x86 and
Windows x64 platforms.
After you have downloaded SmartRF Studio from the web, extract the zip-file, run the installer and follow
the instructions. Select the complete installation to include the SmartRF Studio program, the SmartRF
Studio documentation and the necessary drivers needed to communicate with the SmartRF06EB.
6
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Getting Started
www.ti.com
3.1.1
SmartRF Studio
SmartRF Studio is a PC application developed for configuration and evaluation of many RF-IC products
from Texas Instruments. The application is designed for use with SmartRF Evaluation Boards, such as
SmartRF06EB, and runs on the Microsoft Windows operating systems.
SmartRF Studio lets you explore and experiment with the RF-ICs as it gives full overview and access to
the devices’ registers to configure the radio and has a control interface for simple radio operation from the
PC.
This means that SmartRF Studio will help radio system designers to easily evaluate the RF-IC at an early
stage in the design process. It also offers a flexible code export function of radio register settings for
software developers.
The latest version of SmartRF Studio can be downloaded from the Texas Instruments website [1], where a
complete user manual can be found.
3.1.2
FTDI USB Driver
SmartRF PC software such as SmartRF Studio uses a proprietary USB driver from FTDI [2] to
communicate with SmartRF06 evaluation boards. Connect your SmartRF06EB to the computer with a
USB cable and turn it on. If you did a complete install of SmartRF Studio, the device is automatically
recognized by Windows and the SmartRF06EB is ready for use!
3.1.2.1
Install FTDI USB Driver Manually in Windows
If the SmartRF06EB was not properly recognized after plugging it into your PC, try the following steps to
install the necessary USB drivers. The steps described are for Microsoft Windows 7, but are very similar to
those in Windows XP and Windows Vista. It is assumed that you have already downloaded and installed
the latest version of SmartRF Studio 7 [1].
Open the Windows Device Manager and right click on the first “Texas Instruments XDS100v3” found
under “Other devices” as shown in Figure 1.
Select “Update Driver Software…” and, in the appearing dialog, browse to \Drivers\ftdi
as shown in Figure 2.
Figure 1. Driver Install: Update Driver
Figure 2. Driver Install: Specify Path to FTDI Drivers
Press Next and wait for the driver to be installed. The selected device should now appear in the Device
Manager as “TI XDS100v3 Channel x” (x = A or B) as seen in Figure 4. Repeat the above steps for the
second “Texas Instruments XDS100v3” listed under “Other devices”.
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
7
Getting Started
3.1.2.1.1
www.ti.com
Enable XDS100v3 UART Back Channel on Windows
If you have both “TI XDS100v3 Channel A” and “TI XDS100v3 Channel B” listed under Universal Serial
Bus Controllers, you can proceed. Right click on “TI XDS100v3 Channel B” and select Properties. Under
the Advanced tab, make sure “Load VCP” is checked as shown in Figure 3.
A “USB Serial Port” may be listed under “Other devices”, as seen in Figure 1. Follow the same steps as
for the “Texas Instruments XDS100v3” devices to install the VCP driver. When the drivers from \Drivers\ftdi is properly installed, you should see the USB Serial Port device be listed under
“Ports (COM & LPT)” as shown in Figure 4.
The SmartRF06EB drivers are now installed correctly.
Figure 3. Driver Install: VCP Loaded
3.1.2.2
Figure 4. Driver Install: Drivers Successfully Installed
Install XSD100v3 UART Back Channel on Linux
The ports on SmartRF06EB will typically be mounted as ttyUSB0 or ttyUSB1. The UART back channel is
normally mounted as ttyUSB1.
1. Download the Linux drivers from [2].
2. Untar the ftdi_sio.tar.gz file on your Linux system.
3. Connect the SmartRF06EB to your system.
4. Install driver:
(a) Verify the USB Product ID (PID) and Vendor ID (VID). The TI XDS100v3 USB VID is 0x0403 and
the PID is 0xA6D1, but if you wish to find the PID using a terminal window/shell, use
> lsusb | grep -i
future.
(b) Install driver using modprobe In a terminal window/shell, navigate to the ftdi_sio folder and run
> sudo modprobe ftdi_sio vendor=0x403
product=0xA6D1 .
SmartRF06EB should now be correctly mounted. The above steps have been tested on Fedora and
Ubuntu distributions.
If the above steps failed, try uninstalling ‘brltty’ prior to step 4 (technical note TN_101, [2]):
> sudo apt-get remove brltty.
8
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Using the SmartRF06 Evaluation Board
www.ti.com
4
Using the SmartRF06 Evaluation Board
The SmartRF06EB is a flexible test and development platform that works together with RF Evaluation
Modules from Texas Instruments.
An Evaluation Module is a small RF module with RF chip, balun, matching filter, SMA antenna connector
and I/O connectors. The modules can be plugged into the SmartRF06EB, which lets the PC take direct
control of the RF device on the EVM over the USB interface.
SmartRF06EB currently supports: CC2538EM
SmartRF06EB is included in the CC2538 development kit.
Figure 5. SmartRF06EB (rev. 1.2.1) With EVM Connected
The PC software that controls the SmartRF06EB + EVM is SmartRF Studio. Studio can be used to
perform several RF tests and measurements, for example, to set up a CW signal and send or receive
packets.
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
9
Using the SmartRF06 Evaluation Board
www.ti.com
The EB+EVM can be of great help during the whole development cycle for a new RF product.
• Perform comparative studies. Compare results obtained with EB+EVM with results from your own
system.
• Perform basic functional tests of your own hardware by connecting the radio on your board to
SmartRF06EB. SmartRF Studio can be used to exercise the radio.
• Verify your own software with known good RF hardware, by simply connecting your own
microcontroller to an EVM via the EB. Test the send function by transmitting packets from your
software and receive with another board using SmartRF Studio. Then, transmit using SmartRF Studio
and receive with your own software.
• Develop code for your SoC and use the SmartRF06EB as a standalone board without PC tools.
The SmartRF06EB can also be used as a debugger interface to the SoCs from IAR Embedded workbench
for ARM or Code Composer Studio from Texas Instruments. For details on how to use the SmartRF06EB
to debug external targets, see Section 6.
4.1
Absolute Maximum Ratings
The minimum and maximum operating supply voltages and absolute maximum ratings for the active
components onboard the SmartRF06EB are summarized in Table 3. Table 3 lists the recommended
operating temperature and storage temperature ratings. For more details, see the device-specific data
sheet.
Table 3. Supply Voltage: Recommended Operating Conditions and Absolute Maximum Ratings
Component
Operating Voltage
Absolute Maximum Rating
Min [V]
Max [V]
Min [V]
Max [V]
+1.8
+3.6
–0.3
+3.75
LCD [5]
+3.0
+3.3
–0.3
+3.6
Accelerometer [6]
+1.62
+3.6
–0.3
+4.25
Ambient light sensor [7]
+2.3
+5.5
NA
+6
XDS100v3 Emulator
[4]
(1)
(2)
(1)
(2)
The XDS100v3 Emulator is USB powered. Values refer to the supply and I/O pin voltages of the connected target.
Recommended minimum operating voltage.
Table 4. Temperature: Recommended Operating Conditions and Storage Temperatures
Component
10
Operating Voltage
Absolute Maximum Rating
Min [V]
Max [V]
Min [V]
Max [V]
XDS100v3 Emulator [4]
–20
+70
–50
+110
LCD [5]
–20
+70
–30
+80
Accelerometer [6]
–40
+85
–50
+150
Ambient light sensor [7]
–40
+85
–40
+85
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board Overview
www.ti.com
5
SmartRF06 Evaluation Board Overview
SmartRF06EB acts as the motherboard in development kits for ARM Cortex-based low power RF SoCs
from Texas Instruments. The board has several user interfaces and connections to external interfaces,
allowing fast prototyping and testing of both software and hardware. An overview of the SmartRF06EB
architecture is found in Figure 6. The board layout is found in Figure 7 and Figure 8, while the schematics
are located in Appendix A.
This section provides an overview of the general architecture of the board and describes the available I/O.
The following subsections explain the I/O in more detail. Pin connections between the EVM and the
evaluation board I/O can be found in Section 5.10.
Figure 6. SmartRF06EB Architecture
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
11
SmartRF06 Evaluation Board Overview
www.ti.com
EM I/O breakout
EM connectors
Ambient Light
Sensor
XDS LEDs
EM current
measurement
testpoint and
jumper
LEDs
Accelerometer
XDS bypass
header
Main power
switch
Power source
selection switch
20-pin ARM
JTAG Header
EM reset button
UART back
channel enable
Jumper
Regulator
bypass jumper
10-pin ARM
Cortex Header
External power
supply connector
General purpose
buttons
LCD
UART back
channel
breakout
Micro SD
card slot
Figure 7. SmartRF06EB Revision 1.2.1 Front Side
XDS100v3
Emulator
1.5 V AAA
Alkaline Battery
holder
1.5 V AAA
Alkaline Battery
holder
CR2032 coin
cell battery
holder
Figure 8. SmartRF06EB Revision 1.2.1 Reverse Side
12
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board Overview
www.ti.com
5.1
XDS100v3 Emulator
The XDS100v3 Emulator from Texas Instruments has cJTAG and regular JTAG support. cJTAG is a 2-pin
extension to regular 4-pin JTAG. The XDS100v3 consists of a USB to JTAG chip from FTDI [2] and an
FPGA to convert JTAG instructions to cJTAG format.
In addition to regular debugging capabilities using cJTAG or JTAG, the XDS100v3 Emulator supports a
UART backchannel over a USB Virtual COM Port (VCP) to the PC. The UART back channel supports flow
control, 8-N-1 format and data rates up to 12Mbaud.
For detailed information about the emulator, see the XDS100v3 emulator product page [4]. The XDS100v3
Emulator is powered over USB and is switched on as long as the USB cable is connected to the
SmartRF06EB and the main power switch (S501) is in the ON position. The XDS100v3 Emulator supports
targets with operating voltages between 1.8 V and 3.6 V. The min (max) operating temperature is -20
(+70) °C.
5.1.1
UART Back Channel
The mounted EVM can be connected to the PC via the XDS100v3 Emulator’s UART back channel. When
connected to a PC, the XDS100v3 is enumerated as a Virtual COM Port (VCP) over USB. The driver used
is a royalty free VCP driver from FTDI, available, for example, on Microsoft Windows, Linux and Max OS
X. The UART back channel gives the mounted EVM access to a four pin UART interface, supporting 8-N1 format at data rates up to 12 Mbaud.
To enable the SmartRF06EB UART back channel the “Enable UART over XDS100v3” jumper (J5),
located on the lower right side of the EB, must be mounted (see Figure 9). Table 5 shows an overview of
the I/O signals related to UART Back Channel.
Figure 9. Jumper Mounted on J5 to Enable the UART Back Channel
Table 5. UART Back Channel Signal Connections
5.2
Signal Name
Description
Probe Header
RF1.7_UART_RX
UART receive (EVM data in)
EM_UART_RX (P412.2)
EVM Pin
RF1.7
RF1.9_UART_TX
UART transmit (EVM data out)
EM_UART_TX (P412.3)
RF1.9
RF1.3_UART_CTS
UART clear to send signal
EM_UART_CTS (P412.4)
RF1.3
RF2.18_UART_RTS
UART request to send signal
EM_UART_RTS (P412.5)
RF2.18
Power Sources
There are three ways to power the SmartRF06EB: batteries, USB bus and external power supply. The
power source can be selected using the power source selection switch (S502) seen in Figure 10. The
XDS100v3 Emulator can only be powered over USB. The main power supply switch (S501) cuts power to
the SmartRF06EB.
CAUTION
Never connect batteries and an external power source to the SmartRF06EB at
the same time! Doing so may lead to excessive currents that may damage the
batteries or cause onboard components to break. The CR2032 coin cell battery
is in particular very sensitive to reverse currents (charging) and must never be
combined with other power sources (AAA batteries or an external power
source).
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
13
SmartRF06 Evaluation Board Overview
www.ti.com
Figure 10. Main Power Switch (P501)
5.2.1
Figure 11. Source Selection Switch (P502)
USB Power
When the SmartRF06EB is connected to a PC via a USB cable, it can draw power from the USB bus. The
onboard voltage regulator supplies approximately 3.3 V to the mounted EVM and the EB peripherals. To
power the mounted EVM and the EB peripherals from the USB bus, the power source selection switch
(S502) should be in “USB” position (see Figure 12).
The maximum current consumption is limited by the regulator to 1500 mA.
NOTE: Most USB power sources are limited to 500 mA.
Figure 12. SmartRF06EB Power Selection Switch (P502) in “USB” Position
5.2.2
Battery Power
The SmartRF06EB can be powered using two 1.5 V AAA alkaline batteries or a 3 V CR2032 coin cell
battery. The battery holders for the AAA batteries and the CR2032 coin cell battery are located on the
reverse side of the PCB. To power the mounted EVM and the EB peripherals using batteries, the power
source selection switch (S502) should be in “BAT” position (see Figure 13).
When battery powered, the EVM power domain is by default regulated to 2.1 V. The voltage regulator may
be bypassed by mounting a jumper on J502. For more details, see Section 5.3.2.
CAUTION
Do not power the SmartRF06EB using two 1.5 V AAA batteries and a 3 V
CR2032 coin cell battery at the same time. Doing so may lead to excessive
currents that may damage the batteries or cause onboard components to break
Figure 13. SmartRF06EB Power Source Selection Switch (P502) in “BAT” Position
14
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board Overview
www.ti.com
5.2.3
External Power Supply
The SmartRF06EB can be powered using an external power supply. To power the mounted EVM and the
EB peripherals using an external power supply, the power source selection switch (S502) should be in
“BAT” position (see Figure 13).
The external supply’s ground should be connected to the SmartRF06EB ground, for example, to the
ground pad in the top left corner of the EB. Connect the positive supply connector to the external power
header J501 (see Figure 14). The applied voltage must be in the range from 2.1 V to 3.6 V and limited to
max 1.5 A.
When powered by an external power supply, the EVM power domain is by default regulated to 2.1 V. The
voltage regulator may be bypassed by mounting a jumper on J502. For more details, see Section 5.3.2.
CAUTION
There is a risk of damaging the onboard components if the applied voltage on
the external power connector/header is lower than -0.3 V or higher than 3.6 V
(combined absolute maximum ratings for onboard components). For more
information, see Section 4.1.
Figure 14. SmartRF06EB External Power Supply Header (J501)
5.3
Power Domains
The SmartRF06EB is divided into three power domains, described in detail in the following sections. The
SmartRF06EB components, and what power domain they belong to, is shown in Figure 15 and Table 6.
Mounted EM
XDS domain
(3.3 V)
Level
EM domain
(1.8 - 3.6 V)
Level
3.3 V domain
(3.3 V)
XDS100v3, XDS LEDs
shifters
ACC, ALS, keys, LEDs
shifters
LCD, SD card
Power sources
USB, batteries, external supply
Figure 15. Power Domain Overview of SmartRF06EB
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
15
SmartRF06 Evaluation Board Overview
www.ti.com
Table 6. Power Domain Overview of SmartRF06EB
Component
Power Domain
Power Source
Evaluation Module
EVM domain (LO_VDD)
USB, battery, external
General Purpose LEDs
EVM domain (LO_VDD)
USB, battery, external
Accelerometer
EVM domain (LO_VDD)
USB, battery, external
Ambient Light Sensor
EVM domain (LO_VDD)
USB, battery, external
Current Measurement MSP MCU
EVM domain (LO_VDD)
USB, battery, external
LEDs
EVM domain (LO_VDD)
USB, battery, external
XDS100v3 Emulator
XDS domain
USB
XDS100v3 LEDs
XDS domain
USB
SD Card Slot
3.3 V domain (HI_VDD)
Same as EVM domain
LCD
3.3 V domain (HI_VDD)
Same as EVM domain
5.3.1
XDS Domain
The XDS100v3 Emulator (see Section 5.1) onboard the SmartRF06EB is in the XDS domain. The XDS
domain is powered over USB. The USB voltage supply (+5 V) is down-converted to +3.3 V and +1.5 V for
the different components of the XDS100v3 Emulator.
The SmartRF06EB must be connected to a PC over USB for the XDS domain to be powered up. The
domain is turned on or off by the SmartRF06EB main power switch.
5.3.2
EVM Domain
The mounted EVM board and most of the SmartRF06EB peripherals are powered in the EVM domain and
signals in this domain (accessible by the EVM), are prefixed “LV_” in the schematics. Table 6 lists the EB
peripherals that are powered in the EVM domain. The domain is turned on or off by the SmartRF06EB
power switch.
The EVM domain may be powered using various power sources: USB powered (regulated to 3.3 V),
battery powered (regulated to 2.1 V or unregulated) and using an external power supply (regulated to 2.1
V or unregulated).
When battery powered or powered by an external source, the EVM power domain is by default regulated
to 2.1 V using a step down converter. The step down converter may be bypassed by mounting a jumper
on J502 (see Figure 16), powering the EVM domain directly from the source. When J502 is not mounted,
the EVM power domain is regulated to 2.1 V. The maximum current consumption of the EVM power
domain is then limited by the regulator to 410 mA.
Figure 16. Mount a Jumper on J502 to Bypass EVM Domain Voltage Regulator
NOTE: Mounting a jumper on J502 will not have any effect if the SmartRF06EB is powered over
USB (when the power source selection switch, S502, is in “USB” position).
16
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board Overview
www.ti.com
5.3.3
3.3 V Domain
The 3.3 V domain is a sub domain of the EVM domain. The 3.3 V domain is regulated to 3.3 V using a
buck-boost converter, irrespective of the source powering the EVM domain. Signals in the 3.3 V domain
(controlled by the EVM) are prefixed “HV_” for High Voltage in the schematics.
Two EB peripherals are in the 3.3 V domain, the LCD and the SD card slot, as listed in Table 6. These
peripherals are connected to the EVM domain via level shifters U401 and U402.
The 3.3 V domain may be switched on (off) completely by the mounted EVM board by pulling signal
LV_3.3V_EN to a logical 1 (0). For details about the mapping between the EVM and signals onboard the
SmartRF06EB, see Table 15.
5.4
LCD
The SmartRF06EB comes with a 128x64 pixels display from Electronic Assembly (DOGM128E-6) [4]. The
LCD display is available to mounted EVM via a SPI interface, enabling software development of user
interfaces and demo use. Table 7 shows an overview of the I/O signals related to the LCD.
The recommended operating condition for the LCD display is a supply voltage between 3.0 V and 3.3 V.
The LCD display is powered from the 3.3 V power domain (HI_VDD). The min (max) operating
temperature is –20 (+70) °C.
CAUTION
The LCD connector on SmartRF06EB is very tight to ensure proper contact
between the EVM and the LCD. Be extremely cautious when removing the LCD
to avoid the display from breaking.
Table 7. LCD Signal Connections
5.5
Signal Name
Description
Probe Header
LV_3.3V_EN
3.3 V domain enable signal
RF1.15 (P407.1)
EVM Pin
RF1.15
LV_LCD_MODE
LCD mode signal
RF1.11 (P406.7)
RF1.11
;LV_LCD_RESET
LCD reset signal (active low)
RF1.13 (P406.9)
RF1.13
;LV_LCD_CS
LCD chip select (active low)
RF1.17 (P407.3)
RF1.17
LV_SPI_SCK
SPI clock
RF1.16_SCK (P407.2)
RF1.16
LV_SPI_MOSI
SPI MOSI (LCD input)
RF1.18_MOSI (P407.4)
RF1.18
Micro SD Card Slot
The SmartRF06EB has a micro SD card slot for connecting external SD/MMC flash devices (flash device
not included). A connected flash device is available to the mounted EVM via a SPI interface, giving it
access to extra flash, enabling over-the-air upgrades and more. Table 9 shows an overview of I/O signals
related to the micro SD card slot.
The micro SD card is powered from the 3.3 V power domain (HI_VDD).
Table 8. Micro SD Card Signal Connections
Signal Name
Description
Probe Header
(1)
EVM Pin
LV_3.3V_EN
3.3 V domain enable signal
RF1.15 (P407.1)
RF1.15
;LV_SDCARD_CS
SD card chip select (active low) RF2.12 (P411.1)
RF2.12
LV_SPI_SCK
SPI clock
RF1.16_SCK (P407.2)
RF1.16
LV_SPI_MOSI
SPI MOSI (SD card input)
RF1.18_MOSI (P407.4)
RF1.18
LV_SPI_MISO
SPI MISO (SD card output)
RF1.20_MISO (P407.5)
RF1.20
(1)
The LCD and SD card are both powered in the 3.3 V domain and cannot be powered on or off individually.
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
17
SmartRF06 Evaluation Board Overview
5.6
www.ti.com
Accelerometer
The SmartRF06EB is equipped with a BMA250E digital accelerometer from Bosch Sensortech [6]. The
accelerometer is available to the mounted EVM via an SPI interface and has two dedicated interrupt lines.
The accelerometer is suitable for application development, prototyping and demo use. Table 9 shows an
overview of I/O signals related to the accelerometer.
Note that some versions of the SmartRF06EB (1.2.2 and earlier – see the sticker on bottom side of PCB)
used the original BMA250 IC, while later versions (1.2.3 and later) use BMA250E. The primary difference
is that the BMA250E uses a different device ID. For more information, see the Bosch Sensortech data
sheet [6].
The recommended operating condition for the accelerometer is a supply voltage between 1.62 V and 3.6
V. The min (max) operating temperature is -40 (+85) °C
Table 9. Accelerometer Signal Connections
5.7
Signal Name
Description
Probe Header
LV_ACC_PWR
Acc. power enable signal
RF2.8 (P407.8)
EVM Pin
RF2.8
LV_ACC_INT1
Acc. interrupt signal
RF2.16 (P411.5)
RF2.16
LV_ACC_INT2
Acc. interrupt signal
RF2.14 (P411.3)
RF2.14
;LV_ACC_CS
Acc. chip select (active low)
RF2.10 (P407.9)
RF2.10
LV_SPI_SCK
SPI clock
RF1.16_SCK (P407.2)
RF1.16
LV_SPI_MOSI
SPI MOSI (acc. input)
RF1.18_MOSI (P407.4)
RF1.18
LV_SPI_MISO
SPI MISO (acc. output)
RF1.20_MISO (P407.5)
RF1.20
Ambient Light Sensor
The SmartRF06EB has an analog SFH 5711 ambient light sensor (ALS) from Osram [7] that is available
for the mounted EVM via the EVM connectors, enabling quick application development for demo use and
prototyping. Figure 17 and Table 10 shows an overview of I/O signals related to the ambient light sensor.
The recommended operating condition for the ambient light sensor is a supply voltage between 2.3 V and
5.5 V. The min (max) operating temperature is -40 (+85) °C.
Figure 17. Simplified Schematic of Ambient Light Sensor Setup
Table 10. Ambient Light Sensor Signal Connections
18
Signal Name
Description
Probe Header
EVM Pin
LV_ALS_PWR
ALS power enable signal
RF2.6 (P407.7)
RF2.6
LV_ALS_OUT
ALS output signal (analog)
RF2.5 (P411.6)
RF2.5
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board Overview
www.ti.com
5.8
Buttons
There are six buttons on the SmartRF06EB. Status of the LEFT, RIGHT, UP, DOWN and SELECT
buttons are available to the mounted EVM. These buttons are intended for user interfacing and
development of demo applications.
The EVM RESET button resets the mounted EVM by pulling its reset line low (RF2.15_RESET;). Table 11
shows an overview of I/O signals related to the buttons.
Table 11. Button Signal Connections
5.9
5.9.1
Signal Name
Description
Probe Header
EVM Pin
LV_BTN_LEFT
Left button (active low)
RF1.6 (P406.4)
RF1.6
LV_BTN_RIGHT
Right button (active low)
RF1.8 (P406.5)
RF1.8
LV_BTN_UP
Up button (active low)
RF1.10 (P406.6)
RF1.10
LV_BTN_DOWN
Down button (active low)
RF1.12 (P406.8)
RF1.12
LV_BTN_SELECT
Select button (active low)
RF1.14 (P406.10)
RF1.14
;LV_BTN_RESET
EVM reset button (active low)
RF2.15_RESET; (P411.4)
RF2.15
LEDs
General Purpose LEDs
The four LEDs D601, D602, D603, D604 can be controlled from the mounted EVM and are suitable for
demo use and debugging. The LEDs are active high. Table 12 shows an overview of I/O signals related to
the LEDs.
Table 12. General Purpose LED Signal Connections
5.9.2
Signal Name
Description
Probe Header
EVM Pin
LV_LED_1
LED 1 (red)
RF2.11 (P407.10)
RF2.11
LV_LED_2
LED 2 (yellow)
RF2.13 (P411.2)
RF2.13
LV_LED_3
LED 3 (green)
RF1.2 (P406.1)
RF1.2
LV_LED_4
LED 4 (red-orange)
RF1.4 (P406.2)
RF1.4
XDS100v3 Emulator LEDs
The XDS100v3 emulator has two LEDs to indicate its status: D2 and D4. The LEDs are located on the top
side of the SmartRF06EB. LED D2 is lit whenever the XDS100v3 Emulator is powered, while LED D4
(ADVANCED MODE) is lit when the XDS100v3 is in an active cJTAG debug state.
5.10 EVM Connectors
The EVM connectors, shown in Figure 18, are used for connecting an EVM board to the SmartRF06EB.
The connectors RF1 and RF2 are the main interface and are designed to inhibit incorrect mounting of the
EVM board. The pin-out of the EVM connectors is given in Table 13 and Table 14.
Figure 18. SmartRF06EB EVM Connectors RF1 and RF2
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
19
SmartRF06 Evaluation Board Overview
www.ti.com
Table 13. EVM connector RF1 Pin Out
20
EVM Pin
Signal Name
Description
RF1.1
GND
Ground
Probe Header
Breakout Header
RF1.2
RF1.2
GPIO signal to EVM
board
P406.1
P403.1-2
RF1.3
RF1.3_UART_CTS
UART back channel /
GPIO
P412.4
P408.15-16
RF1.4
RF1.4
GPIO signal to EVM
board
P406.2
P403.3-4
RF1.5
RF1.5
GPIO signal to EVM
board
P406.3
P403.5-6
RF1.6
RF1.6
GPIO signal to EVM
board
P406.4
P403.7-8
RF1.7
RF1.7_UART_RX
UART back channel
(EVM RX)
P412.2
P408.11-12
RF1.8
RF1.8
GPIO signal to EVM
board
P406.5
P403.9-10
RF1.9
RF1.9_UART_TX
UART back channel
(EVM TX)
P412.3
P408.13-14
RF1.10
RF1.10
GPIO signal to EVM
board
P406.6
P403.11-12
RF1.11
RF1.11
GPIO signal to EVM
board
P406.7
P403.13-14
RF1.12
RF1.12
GPIO signal to EVM
board
P406.8
P403.15-16
RF1.13
RF1.13
GPIO signal to EVM
board
P406.9
P403.17-18
RF1.14
RF1.14
GPIO signal to EVM
board
P406.10
P403.19-20
RF1.15
RF1.15
GPIO signal to EVM
board
P407.1
P404.1-2
RF1.16
RF1.16_SPI_SCK
EVM SPI Clock
P407.2
P404.3-4
RF1.17
RF1.17
GPIO signal to EVM
board
P407.3
P404.5-6
RF1.18
RF1.18_SPI_MOSI
EVM SPI MOSI
P407.4
P404.7-8
RF1.19
GND
Ground
RF1.20
RF1.20_SPI_MISO
EVM SPI MISO
P407.5
P404.9-10
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board Overview
www.ti.com
Table 14. EVM Connector RF2 Pin Out
EVM Pin
Signal Name
Description
RF2.1
RF2.1_JTAG_TCK
JTAG test clock
Probe Header
Breakout Header
P409.9
RF2.2
GND
Ground
P408.1-2
RF2.3
RF_VDD2
EVM power
TP10
J503.1-2
RF2.4
RF2.4_JTAG_TMS
JTAG test mode select
P409.7
P408.3-4
RF2.5
RF2.5
GPIO signal to EVM
board
P407.6
P404.11-12
RF2.6
RF2.6
GPIO signal to EVM
board
P407.7
P404.13-14
RF2.7
RF_VDD1
EVM power
TP10
J503.1-2
RF2.8
RF2.8
GPIO signal to EVM
board
P407.8
P404.15-16
RF2.9
RF_VDD1
EVM power
TP10
J503.1-2
RF2.10
RF2.10
GPIO signal to EVM
board
P407.9
P404.17-18
RF2.11
RF2.11
GPIO signal to EVM
board
P407.10
P404.19-20
RF2.12
RF2.12
GPIO signal to EVM
board
P411.1
P405.1-2
RF2.13
RF2.13
GPIO signal to EVM
board
P411.2
P405.3-4
RF2.14
RF2.14
GPIO signal to EVM
board
P411.3
P405.5-6
RF2.15
RF2.15_RESET;
EVM reset signal (active
low)
P411.4
P405.7-8
RF2.16
RF2.16
GPIO signal to EVM
board
P411.5
P405.9-10
RF2.17
RF2.17_JTAG_TDI
GPIO / JTAG test data in
P409.5
P408.5-6
RF2.18
RF2.18_UART_RTS
GPIO / UART back
channel
P412.5
P408.17-18
RF2.19
RF2.19_JTAG_TDO
GPIO / JTAG test data out
P409.13
P408.7-8
RF2.20
GND
Ground
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
21
SmartRF06 Evaluation Board Overview
www.ti.com
5.11 Breakout Headers and Jumpers
The SmartRF06EB has several breakout headers, giving access to all EVM connector pins. An overview
of the SmartRF06EB I/O breakout headers is given in Figure 19. Probe headers P406, P407, P411 and
P412 give access to the I/O signals of the mounted EVM. Breakout headers P403, P404 and P405 allow
the user to map any EVM I/O signal to any peripheral on the SmartRF06EB.
The XDS bypass header (P408) makes it possible to disconnect the XDS100v3 Emulator onboard the EB
from the EVM. Using the 20-pin ARM JTAG header (P409) or the 10-pin ARM Cortex Debug Header
(P410), it is possible to debug external targets using the onboard emulator.
NOTE: By default, all jumpers are mounted on P403, P404, P405 and P408. The default
configuration is assumed in this user’s guide, unless otherwise stated.
Evaluation
Module
Peripheral
probe headers
P406, P407,
P411
20-pin
ARM-JTAG
Debug Header
P409
I/O breakout headers
P403, P404, P405
XDS bypass header
P408
SmartRF06EB
peripherals
ACC, ALS, keys, LCD,
LED, SD card
XDS100v3
Emulator
10-pin Cortex
Debug Header
P410
UART back
channel probe
header
P412
Figure 19. SmartRF06EB I/O Breakout Overview
22
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board Overview
www.ti.com
5.11.1
I/O Breakout Headers
The I/O breakout headers on SmartRF06EB consist of pin connectors P406, P407, P411 and P412. P406,
P407 and P411 are located at the top left side of SmartRF06EB. All EVM signals available on these probe
headers can be connected to or disconnected from SmartRF06EB peripherals using jumpers on headers
P403, P404, P405.
Probe header P412 is located near the bottom right corner of the SmartRF06EB. The signals available on
P412 are connected to the XDS100v3 Emulator’s UART back channel using jumpers on header P408.
The I/O breakout mapping between the SmartRF06EB and the mounted EVM is given in Table 15. The
leftmost column in the table refers to the silk print seen on the SmartRF06EB. The rightmost column
shows the corresponding CC2538 I/O pad on CC2538EM.
Table 15. SmartRF06EB I/O Breakout Overview
Probe Header
P406
P407
P411
P412
Silk Print
EB Signal Name
EVM Connector
CC2538EM
I/O
RF1.2
LV_LED_3
RF1.2
PC2
RF1.4
LV_LED_4
RF1.4
PC3
RF1.5
NC
RF1.5
PB1
RF1.6
LV_BTN_LEFT
RF1.6
PC4
RF1.8
LV_BTN_RIGHT
RF1.8
PC5
RF1.10
LV_BTN_UP
RF1.10
PC6
RF1.11
LV_LCD_MODE
RF1.11
PB2
RF1.12
LV_BTN_DOWN
RF1.12
PC7
RF1.13
;LV_LCD_RESET
RF1.13
PB3
RF1.14
LV_BTN_SELECT
RF1.14
PA3
RF1.15
LV_3.3V_EN
RF1.15
PB4
RF1.16_SCK
LV_SPI_SCK
RF1.16
PA2
RF1.17
;LV_LCD_CS
RF1.17
PB5
RF1.18_MOSI
LV_SPI_MOSI
RF1.18
PA4
RF1.20_MISO
LV_SPI_MISO
RF1.20
PA5
RF2.5
LV_ALS_OUT
RF2.5
PA6
RF2.6
LV_ALS_PWR
RF2.6
PA7
RF2.8
LV_ACC_PWR
RF2.8
PD4
RF2.10
;LV_ACC_CS
RF2.10
PD5
RF2.11
LV_LED_1
RF2.11
PC0
RF2.12
;LV_SDCARD_CS
RF2.12
PD0
RF2.13
LV_LED_2
RF2.13
PC1
RF2.14
LV_ACC_INT2
RF2.14
PD1
RF2.15_RESET
;LV_BTN_RESET
RF2.15
nRESET
RF2.16
LV_ACC_INT1
RF2.16
PD2
EM_UART_RX
RF1.7_UART_RX
RF1.7
PA0
EM_UART_TX
RF1.9_UART_TX
RF1.9
PA1
EM_UART_CTS
RF1.3_UART_CTS
RF1.3
PB0
EM_UART_RTS
RF2.18_UART_RTS
RF2.18
PD3
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
23
SmartRF06 Evaluation Board Overview
5.11.2
www.ti.com
XDS100v3 Emulator Bypass Headers
The XDS100v3 Emulator bypass header, P408, is by default mounted with jumpers (see Figure 20),
connecting the XDS100v3 Emulator to a mounted EVM or external target. By removing the jumpers on
P408, the XDS100v3 Emulator can be disconnected from the target.
Figure 20. XDS100v3 Emulator Bypass Header (P408)
5.11.3
20-Pin ARM JTAG Header
The SmartRF06EB comes with a standard 20-pin ARM JTAG header [8] (see Figure 21), enabling the
user to debug an external target using the XDS100v3 Emulator. The pin-out of the ARM JTAG header is
given in Table 16. Section 6 has more information on how to debug an external target using the
XDS100v3 Emulator onboard the SmartRF06EB.
Figure 21. 20-Pin ARM JTAG Header (P409)
Table 16. 20-Pin ARM JTAG Header Pin-Out (P409)
24
Pin
Signal
Description
EB Signal Name
XDS Bypass Header
P409.1
VTRef
Voltage reference
VDD_SENSE
P408.19-20
P409.2
VSupply
Voltage supply
NC
P409.3
nTRST
Test reset
NC
P409.4
GND
Ground
GND
P409.5
TDI
Test data in
RF2.17_JTAG_TDI
P409.6
GND
Ground
GND
P409.7
TMS
Test mode select
RF2.4_JTAG_TMS
P409.8
GND
Ground
GND
P409.9
TCK
Test clock
RF2.1_JTAG_TCK
P409.10
GND
Ground
GND
P409.11
RTCK
Return clock
NC
P409.12
GND
Ground
GND
P409.13
TDO
Test data out
RF2.19_JTAG_TDO
P409.14
GND
Ground
GND
P409.15
nSRST
System reset
RF2.15_RESET;
GND
P409.16
GND
Ground
P409.17
DBGRQ
Debug request
NC
P409.18
GND
Ground
GND
P409.19
DBGACK
Debug acknowledge
NC
P409.20
GND
Ground
GND
SmartRF06 Evaluation Board (EVM)
P408.5-6
P408.3-4
P408.1-2
P408.7-8
P408.9-10
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board Overview
www.ti.com
5.11.4
10-Pin ARM Cortex Debug Header
The SmartRF06EB comes with a standard 10-pin ARM Cortex debug header [8] (see Figure 22), enabling
the user to debug an external target using the XDS100v3 Emulator. The ARM Cortex debug header is
located near the right hand edge of the EB. The header pin-out is given in Table 17. Section 6 has more
information on how to debug an external target using the XDS100v3 Emulator onboard the SmartRF06EB.
Figure 22. 10-Pin ARM Cortex Debug Header (P410)
Table 17. 10-Pin ARM Cortex Debug Header Pin-Out (P410)
Pin
Signal
Description
EB Signal Name
XDS Bypass Header
P410.1
VCC
P410.2
TMS
Voltage reference
VDD_SENSE
P408.19-20
Test mode select
RF2.4_JTAG_TMS
P410.3
P408.3-4
GND
Ground
GND
P410.4
TCK
Test clock
RF2.1_JTAG_TCK
P410.5
GND
Ground
GND
P410.6
TDO
Test data out
RF2.19_JTAG_TDO
P410.7
KEY
Key
NC
P410.8
TDI
Test data in
RF2.17_JTAG_TDI
P410.9
GNDDetect
Ground detect
GND
P410.10
nRESET
System reset
RF2.15_RESET;
P408.1-2
P408.7-8
P408.5-6
P408.9-10
5.12 Current Measurement
The SmartRF06EB provides two options for easy measurements of the current consumption of a mounted
EVM. The following sections describe these two options in detail.
5.12.1
Current Measurement Jumper
SmartRF06EB has a current measurement header, J503, for easy measurement of EVM current
consumption. Header J503 is located on the upper right hand side of the EB. By replacing the jumper with
an ammeter, as shown in Figure 23, the current consumption of the mounted EVM can be measured.
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
25
SmartRF06 Evaluation Board Overview
www.ti.com
Figure 23. Measuring Current Consumption Using Jumper J503
Figure 24. Measuring Current Consumption Using Jumper J503
26
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Debugging an External Target Using SmartRF06EB
www.ti.com
6
Debugging an External Target Using SmartRF06EB
You can easily use XDS100v3 Emulator onboard the SmartRF06EB to debug an external target. In this
section, it is assumed that the target is self-powered.
When debugging an external, self-powered target using SmartRF06EB, make sure to remove the jumper
from the current measurement header (J503) as shown in the second scenario of Figure 25. In this
scenario, the onboard XDS100v3 senses the target voltage of the external target. In the left side scenario
of the same figure, the XDS100v3 senses the target voltage of the EB’s EVM domain.
CAUTION
Having a jumper mounted on header J503 when debugging an external target
causes a conflict between the EB’s EVM domain supply voltage and the
target’s supply voltage. This may result in excess currents, damaging the
onboard components of the SmartRF06EB or the target board.
In Figure 25, the right hand side scenario shows how it is possible to debug an EVM mounted on the
SmartRF06EB using an external debugger. In this scenario, all the jumpers must be removed from the
SmartRF06EB header P408 to avoid signaling conflicts between the onboard XDS100v3 Emulator and the
external debugger.
06EB XDS + EM
06EB XDS + external target
External debugger + EM
EM
EM
EM
(EM domain)
(EM domain)
(EM domain)
J503
(mounted)
P408
(jumpers on)
Current measurement jumper
XDS bypass header
J503
J503
(not mounted)
(mounted)
P409/P410
Ext. target
Debug
header
(Target VDD)
P409/P410
P408
P408
(jumpers on)
(jumpers off)
XDS100v3
XDS100v3
External
debugger
XDS100v3
Figure 25. Simplified Connection Diagram for Different Debugging Scenarios
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
27
Debugging an External Target Using SmartRF06EB
6.1
www.ti.com
20-Pin ARM JTAG Header
The SmartRF06EB has a standard 20-pin ARM JTAG header mounted on the right hand side (P409).
Make sure all the jumpers on the XDS bypass header (P408) are mounted and that the jumper is removed
from header J503.
Connect the external board to the 20-pin ARM JTAG header (P409) using a 20-pin flat cable as seen in
Figure 26. Make sure pin 1 on P409 matches pin 1 on the external target. For more info about the 20-pin
ARM JTAG header and the XDS bypass header, see Section 5.11.2 and Section 5.11.3.
Figure 26. Debugging External Target Using SmartRF06EB
6.2
10-Pin ARM Cortex Debug Header
The SmartRF06EB has a standard 10-pin ARM Cortex Debug header mounted on the right hand side
(P410). Make sure all the jumpers on the XDS bypass header (P408) are mounted and that the jumper is
removed from header J503.
Connect the external board to the 10-pin ARM JTAG header using a 10-pin flat cable. Make sure pin 1 on
P410 matches pin 1 on the external target. For more info about the 10-pin ARM Cortex Debug header and
the XDS bypass header, see Section 5.11.2 and Section 5.11.4.
28
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Debugging an External Target Using SmartRF06EB
www.ti.com
6.3
Custom Strapping
If the external board does not have a 20-pin ARM JTAG connector nor a 10-pin ARM Cortex connector,
the needed signals may be strapped from the onboard XDS100v3 Emulator to the external target board.
Make sure all the jumpers on the XDS bypass header (P408) are mounted and that the jumper is removed
from header J503. Table 18 shows the signals that must be strapped between the SmartRF06EB and the
target board. Table 19 shows additional signals that are optional or needed for debugging using 4-pin
JTAG. Figure 27 shows where the signals listed in Table 18 and Table 19 can be found on the 20-pin
ARM JTAG header.
Table 18. Debugging External Target: Minimum Strapping (cJTAG support)
EB Signal Name
EB Breakout
Description
VDD_SENSE
P409.1
Target voltage supply
GND
P409.4
Common ground for EB and external
board
RF2.1_JTAG_TCK
P409.9
Test clock
RF2.4_JTAG_TMS
P409.7
Test mode select
Table 19. Debugging External Target: Optional Strapping
EB Signal Name
EB Breakout
Description
RF2.17_JTAG_TDI
P409.5
Test data in (optional for cJTAG)
RF2.19_JTAG_TDO
P409.13
Test data out (optional for cJTAG)
RF2.15_RESET;
P409.15
Target reset signal (optional)
VDD_SENSE
GND
RF2.17_JTAG_TDI
RF2.4_JTAG_TMS
RF2.1_JTAG_TCK
RF2.19_JTAG_TDO
2-pin cJTAG
RF2.15_RESET
+
4-pin JTAG
Optional
Figure 27. ARM JTAG Header (P409) With Strapping to Debug External Target
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06 Evaluation Board (EVM)
29
Frequently Asked Questions
7
www.ti.com
Frequently Asked Questions
Question: Nothing happens when I power up the evaluation board. Why?
Answer: Make sure that a power source is connected to the EB. Verify that the power source selection
switch (S502) is set correctly according to your power source. When powering the EB from either batteries
or an external power source, S502 should be in the “BAT” position. When powering the EB over USB, the
switch should be in the “USB” position. Also, make sure the EVM current measurement jumper (J503) is
short circuited.
Question: Why are there two JTAG connectors on the SmartRF06EB, and which one should I use?
Answer: The SmartRF06EB comes with two different standard debug connectors: the 20-pin ARM JTAG
connector (P409) and the compact 10-pin ARM Cortex debug connector (P410). These debug connectors
are there to more easily debug external targets without the need of customized strapping. For more details
on how to debug external targets using the SmartRF06EB, see Section 6.
Question: Can I use the SmartRF06EB to debug an 8051 SoC such as CC2530?
Answer: No, you cannot debug an 8051 SoC using the SmartRF06EB.
Question: When connecting my SmartRF06EB to my PC, no serial port appears. Why?
Answer: It may be that the virtual COM port on the SmartRF06EB’s XDS100 channel B has not been
enabled. Section 3.1.2.1.1 describes how to enable the Vritual COM Port in the USB driver.
8
References
1.
2.
3.
4.
5.
6.
7.
8.
30
SmartRF Studio Product Page
FTDI USB Driver Page
SmarRF Flash Programmer Product Page
XDS100 Emulator Programmer wiki
Electronic Assembly DOGM128-6 Data Sheet
Bosch Sensortec BMA250 Data Sheet
Osram SFH 5711
Cortex-M Debug Connectors
SmartRF06 Evaluation Board (EVM)
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Appendix A
SWRU321B – May 2012 – Revised March 2017
Schematics
A.1
SmartRF06EB 1.2.1
FIDUCIAL_MARK_1mm
FM1
FIDUCIAL_MARK_1mm FIDUCIAL_MARK_1mm
FM2
FM3
1
1
1
FIDUCIAL_MARK_1mm FIDUCIAL_MARK_1mm FIDUCIAL_MARK_1mm
FM4
FM5
FM6
1
1
TESTPOINT_PAD
TP12
HOLE_3
H1
XDS100v3 - FPGA
EM INTERFACE/
LEVEL SHIFTERS
1
TESTPOINT_PAD
TP13
HOLE_3
H2
HOLE_3
H3
HOLE_3
H4
XDS100v3 - FTDI
POWER SUPPLY
HIGH VOLTAGE
PERIPHERALS
LOW VOLTAGE
PERIPHERALS
Copyright © 2017, Texas Instruments Incorporated
Figure 28. SmartRF06EB - Top Level
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Schematics
31
SmartRF06EB 1.2.1
www.ti.com
P3.3VXDS
GND
3
1
2 CLK_100M
2
1
VCCPLF
RESET_N
C26
1
C34
C_15N_0402_X7R_K_25
2
2
1
TPD4E002
U7
2
1
R54
R_5K1_0402_J
VDD
OUTPUT
2
1
STANDBY
2
TPD4E002
U12
1
T_EMU5
C27
C_4U7_0603_X5R_K_6
3
T_EMU3
UART_EN_N
IO1
GND
5
IO4
IO2
T_EMU4
1
T_DIS
IO1
2
TPD4E002
GND
4
IO3
T_TRST
3
T_TVD
1
GND
IO4
TPD4E002
IO2
IO3
5
T_TMS
4
T_EMU2
2
J5
2
R33
R_51_0402_G
4
R1
L_BEAD_102_0402
1
2
ASDM
C25
P3.3VXDS
+1.5V
1
C_100N_0402_X5R_K_10
1
R49
R_1K0_0402_F
P3.3VXDS
O1
ASDM 100.000MHZ
C_4U7_0603_X5R_K_6
P3.3VXDS P3.3VXDS
2
PINROW_SMD_1X2_2.54MM
TPD4E002
U8
1
IO1
2
GND
3
T_TDI
IO4
TPD4E002
IO2
IO3
5
T_RTCK
4
T_TDO
TPD4E002
U9
1
T_TCK
IO1
2
TDI
TMS
GND
GND
GND
GBB1/IO38RSB0
GBA0/IO39RSB0
VMV1
GBA1/IO40RSB0
85
84
83
82
81
80
79
78
77
76
VTARGET
1
2
R15
R_51_0402_G
R18
R_51_0402_G
1
1
2
2
R16
R_51_0402_G
R23
R_51_0402_G
R17
R_51_0402_G
R22
R_470_0402_F
1
1
1
1
R21
1
R20
2
2
2
2
R_470_0402_F
2
2
1
2
R41
R_10K_0402_F
T_TMS
T_TDI
PWRGOOD
P3.3VXDS
T_TDO
T_RTCK
P3.3VXDS
T_TCK
T_EMU0
T_SRST
1
PWRGOOD
2
T_EMU1
3
R_470_0402_F
4
5
V_USB
OUTA
INAINA+
V+
U6
OPA2363
OUTB
INB-
V-
INB+
ENA
ENB
GNDQ
VMV0
GBA2/IO41RSB0
IO42RSB0
GBB2/IO43RSB0
GBC2/IO45RSB0
IO47RSB0
VCC
GND
VCCIB0
GCC1/IO51RSB0
GCC0/IO52RSB0
GCA1/IO55RSB0
GCA0/IO56RSB0
GCB2/IO58RSB0
GCC2/IO59RSB0
GDC1/IO61RSB0
GDC0/IO62RSB0
GDA1/IO65RSB0
VJTAG
TRST
TDO
NC
VPUMP
GND
OPA2363
10
9
V_USB
R27
R_1K0_0402_F
1
2
Q1
BC846
1
2
8
7
6
3
1
2
T_TVD
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
Testpoint_Circle_40mils
Testpoint_Circle_40mils
TP8 TP9
P1.8V
2
1
2
50
GBC1/IO36RSB0
GBB0/IO37RSB0
86
VTARGET
1
2
1
C24
PRG_TMS
GBC0/IO35RSB0
P1.5V
2
C_100N_0402_X5R_K_10
49
TCK
T_EMU3
88
87
ADV_MODE
T_TMS
CDBP0130L-G
48
GDA2/IO70RSB1
ADV_MODE
R50
R_1K0_0402_F
R43
PRG_TDI
PRG_TMS
P3.3VXDS
GDB2/IO71RSB1
R_51_0402_G
T_EMU4
1
47
IO32RSB0
R53
2
C_4U7_0603_X5R_K_6
1
46
PRG_TCK
GDC2/IO72RSB1
IO28RSB0
2
2
PRG_TDO
45
IO75RSB1
2
R_10K_0402_F
1
T_EMU2
C23
44
1
EXT_SELECT
T_EMU5
1
PRG_TDI
IO25RSB0
R_51_0402_G
1
R47
EXT_SELECT
C22
43
IO22RSB0
89
R52
2
D1
PRG_TMS
IO81RSB1
2
R_10K_0402_F
P3.3VXDS
42
GND
VCCIB0
IO19RSB0
90
R_51_0402_G
C_100N_0402_X5R_K_10
R44
2
R_10K_0402_F
PRG_TDO
PRG_TCK
IO84RSB1
91
2
R_51_0402_G
1
R48
R_10K_0402_F
IO87RSB1
92
R_51_0402_G
R51
2
VCCIB1
VCC
93
1
R55
R_10K_0402_F
GND
IO15RSB0
R19
1
41
IO11RSB0
IO13RSB0
94
R46
40
IO09RSB0
95
1
39
SUSPEND
VCC
1
P3.3VXDS
ALT_FUNC
IO93RSB1
96
The XDS100 is connected to the EM through
connector P408. See the EM interface page
for details.
R31
38
P3.3VXDS
IO94RSB1
IO07RSB0
T_DIS
T_TRST
2
37
IO95RSB1
GAC1/IO05RSB0
2
R_10K_0402_F
P1.5V
IO96RSB1
GAB1/IO03RSB0
GAC0/IO04RSB0
T_DIS
1
1
36
IO97RSB1
98
97
LED_EL19-21SRC
2 D4
R29
35
IO99RSB1
VTARGET
99
2
34
TDI
TCK
IO100RSB1
GAB0/IO02RSB0
100
R_120K_0402_F
TDO
IO102RSB1
GAA1/IO01RSB0
2
33
GEC2/IO104RSB1
GAA0/IO00RSB0
1
R30
32
T_SRST
P3.3VXDS
1
31
TMS
GEB2/IO105RSB1
P3.3VXDS
A3PN125-VQFP
R_120K_0402_F
30
TRST
3
GEA2/IO106RSB1
A3PN125-ZVQG100
EMU0
EMU_EN
4
1
29
5
R42
R_220_0402_J
28
RTCK
6
T_EMU1
4
2
SRST_OUT
7
5
R12
R_0_0402
27
8
IO3
1
26
1
GND
TVD
CLK_FAIL
2
GAA2/IO67RSB1
IO68RSB1
GAB2/IO69RSB1
IO132RSB1
GAC2/IO131RSB1
IO130RSB1
IO129RSB1
GND
GFB1/IO124RSB1
GFB0/IO123RSB1
VCOMPLF
GFA0/IO122RSB1
VCCPLF
GFA1/IO121RSB1
GFA2/IO120RSB1
VCC
VCCIB1
GEC0/IO111RSB1
GEB1/IO110RSB1
GEB0/IO109RSB1
GEA1/IO108RSB1
GEA0/IO107RSB1
VMV1
GNDQ
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
IO4
TPD4E002
IO2
GND
UART_EN_N
GND
VCCPLF
GND
P3.3VXDS
POD_RLS
EMU1
CBL_DIS
DTSA_BYP
RESET_N
P3.3VXDS
P1.5V
CLK_100M
U11
GND
3
T_EMU0
TP5
TP6
TP7
PRG_TDI
Testpoint_Circle_40mils
PRG_TCK
Testpoint_Circle_40mils
PRG_TRST
2
R25
R_120K_0402_F
2
1
C21
C_100N_0402_X5R_K_10
2
1
Testpoint_Circle_40mils
VTARGET
PRG_TMS
P1.5V
Testpoint_Circle_40mils
VTARGET
TP4
PRG_TDO
PRG_TDO
PRG_TRST
P3.3VXDS
TP3
P3.3VXDS
R24
R_5K1_0402_J
1
Testpoint_Circle_40mils
Copyright © 2017, Texas Instruments Incorporated
Figure 29. SmartRF06EB - XDS100v3 - FPGA
32
Schematics
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06EB 1.2.1
C_100N_0402_X5R_K_10
C14
1
2
C16
1
2
C_100N_0402_X5R_K_10
C11
1
2
C_100N_0402_X5R_K_10
1
2
C12
1
2
C_100N_0402_X5R_K_10
2
C9
1
C6
2
P3.3VXDS P3.3VXDS P3.3VXDS P3.3VXDS P3.3VXDS
P1.8V
C_100N_0402_X5R_K_10
1
C5
2
P1.8V
C_100N_0402_X5R_K_10
1
C4
2
P1.8V
C_100N_0402_X5R_K_10
1
C3
2
P1.8V
C_4U7_0603_X5R_K_6
1
C31
2
+1.5V
C_100N_0402_X5R_K_10
1
C30
2
+1.5V
C_100N_0402_X5R_K_10
1
C29
C28
2
+1.5V
C_100N_0402_X5R_K_10
1
C_4U7_0603_X5R_K_6
+1.5V
C_4U7_0603_X5R_K_6
www.ti.com
P3.3VXDS
R7
L_BEAD_102_0402
2
1
1
1
C20
C_100N_0402_X5R_K_10
C19
2
2
C_4U7_0603_X5R_K_6
P3.3VXDS
R8
L_BEAD_102_0402
1
C17
C_100N_0402_X5R_K_10
IO1
1
5
IO2
TPD2E001
4
GND
1
2
3
ID
4
7
VCCIO
VCCIO
VCCIO
ACBUS0
14
REF
ACBUS2
RESET
ACBUS3
ACBUS4
ACBUS5
ACBUS6
1
R_0_0402
R2
2
1
Shield
DP
ACBUS1
6
Shield
DM
USBDP8
6
5
GND
ADBUS0
ADBUS1
ADBUS2
ADBUS3
ADBUS4
ADBUS5
ADBUS6
ADBUS7
VREGOUT
USBDM7
2
D+
R10
R_12K_0402_F
D-
VREGIN
56
EEPROM_CS
63
EEPROM_CLK
62
EEPROM_DATA
61
2
P3.3VXDS
ACBUS7
EECS
EECLK
EEDATA
FT2232H
BDBUS0
BDBUS1
BDBUS2
OSCI
BDBUS3
3
BDBUS4
DIN
CS
CLK
2
R4
R_1K0_0402_F
2
6
1
R3
R_1K0_0402_F
VCC
93AA46B
1
5
EEPROM_CS
4
EEPROM_CLK
P3.3VXDS
2
BDBUS7
4
1
C13
BDBUS6
3
1
2
TEST
C18
2
BCBUS0
BCBUS1
BCBUS2
BCBUS3
BCBUS4
BCBUS5
BCBUS6
1
BCBUS7
C8
C_100N_0402_X5R_K_10
PWREN
2
15 25 35
GND
GND
11
GND
5
GND
1
GND
GND
10
GND
AGND
SUSPEND
16
24
TCK
TDI
TDO
TMS
TRST
EMU_EN
EMU0
RTCK
26
SRST_OUT
27
CLK_FAIL
28
TVD
29
POD_RLS
30
EMU1
32
CBL_DIS
33
DTSA_BYP
34
ALT_FUNC
38
PRG_TCK
39
PRG_TDI
40
PRG_TDO
41
PRG_TMS
43
PRG_TRST
17
18
19
21
22
23
44
V_USB
45
46
48
52
53
54
1
55
57
LED_EL19-21SYGC
58
2 D2
59
60
PWREN
36
SUSPEND
PWREN
GND
GND
13
C_27P_0402_NP0_J_50
3
DO
Y1
X_12.000/30/30/10/20
C_27P_0402_NP0_J_50
1
R6
R_2K7_0402_F
2
1
2
U1
93AA46B
1
2
EEPROM_DATA
OSCO
BDBUS5
1
R5
R_1K0_0402_F
P3.3VXDSP3.3VXDS
P3.3VXDS
U4
FT2232HL
2
3
NC
2
VBUS
VCC
R_1K0_0402_F
R9
2
42
31
R28
R_270_0402_F
50
49
1
P1
USB-B_MICRO
20
64
1
VBUS
37
VCCIO
12
VCORE
9
VPLL
VPHY
4
VCORE
1
P3.3VXDSP3.3VXDS P1.8V
U3
TPD2E001
P3.3VXDS
P1.8V
1
C15
2
2
C_4U7_0603_X5R_K_6
VCORE
2
47 51
Copyright © 2017, Texas Instruments Incorporated
Figure 30. SmartRF06EB - XDS100v3 - FTDI
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Schematics
33
SmartRF06EB 1.2.1
www.ti.com
EM DEBUG CONNECTION
EM CONNECTORS
RF1
SMD_HEADER_2X10
1
2
RF1.2
3
4
RF1.4
5
6
RF1.6
7
8
RF1.8
9
10
RF1.10
11
12
RF1.12
13
14
RF1.14
15
16
RF1.16_SPI_SCK
17
18
RF1.18_SPI_MOSI
20
19
RF1.20_SPI_MISO
GND
RF1.3_UART_CTS
RF1.5
RF1.7_UART_RX
RF1.9_UART_TX
RF1.11
RF1.13
RF1.15
RF1.17
GND
RF2.1_JTAG_TCK
RF_VDD2
RF2.5
RF_VDD1
RF_VDD1
RF2.11
RF2.13
RF2.15_RESET
RF2.17_JTAG_TDI
RF2.19_JTAG_TDO
Bypass jumper block for connection
between EM and XDS100v3
RF2
SMD_HEADER_2X10
1
2
GND
3
4
RF2.4_JTAG_TMS
5
6
RF2.6
7
8
RF2.8
9
10 RF2.10
11
12 RF2.12
13
14 RF2.14
15
16 RF2.16
17
18 RF2.18_UART_RTS
20 GND
19
P408
T_TCK
1
2
RF2.1_JTAG_TCK
T_TMS
3
4
RF2.4_JTAG_TMS
T_TDI
5
6
RF2.17_JTAG_TDI
T_TDO
7
8
RF2.19_JTAG_TDO
T_SRST
9
10
RF2.15_RESET
T_EMU3
11
12
RF1.7_UART_RX
T_EMU2
13
14
RF1.9_UART_TX
T_EMU5
15
16
RF1.3_UART_CTS
T_EMU4
17
18
RF2.18_UART_RTS
T_TVD
19
20
VDD_SENSE
PINROW_SMD_2X10_2.54MM
EM EB BREAKOUT and PROBE HEADERS
20-pin ARM JTAG Connector
10-pin ARM Cortex
JTAG Connector
P409
VDD_SENSE
LV_LED_3
P403
PINROW_SMD_2X10_2.54MM
RF1.2
1
2
LV_LED_4
3
4
RF1.4
5
6
RF1.5
7
8
RF1.6
1
2
10
RF1.8
11
12
RF1.10
13
14
RF1.11
15
16
RF1.12
LV_BTN_RIGHT
9
LV_BTN_UP
LV_LCD_MODE
LV_BTN_DOWN
3
4
5
PINROW_1X10
6
7
8
9
10
LV_SDCARD_CS
1
2
RF2.12
2
3
4
GND
5
6
GND
LV_LED_2
3
4
RF2.13
LV_ACC_INT2
5
6
RF2.14
LV_BTN_RESET
7
8
RF2.15_RESET
RF2.4_JTAG_TMS
7
8
GND
RF2.1_JTAG_TCK
9
10
GND
11
12
GND
LV_ACC_INT1
9
10
RF2.16
RF2.19_JTAG_TDO
13
14
GND
PINROW_SMD_2X5_2.54MM
RF2.15_RESET
15
16
GND
17
18
GND
19
20
GND
RF2.17_JTAG_TDI
2
20
RF1.14
1
2
RF1.15
LV_SPI_SCK
3
4
RF1.16_SPI_SCK
LV_LCD_CS
5
6
RF1.17
LV_SPI_MOSI
7
8
RF1.18_SPI_MOSI
LV_SPI_MISO
9
10
RF1.20_SPI_MISO
LV_ALS_OUT
11
12
RF2.5
LV_ALS_PWR
13
14
RF2.6
LV_ACC_PWR
15
16
RF2.8
LV_ACC_CS
17
18
RF2.10
LV_LED_1
19
20
RF2.11
3
4
5
PINROW_1X10
18
19
LV_3.3V_EN
6
7
8
9
10
1
2
3
4
5
RF2.12
RF2.13
RF2.14
RF2.15_RESET
RF2.16
LO_VDD
R402
R_0_0603
1
2
3
4
5
1
C401
1
2
C402
Optional
RC filter
EM CURRENT MEASUREMENT
RF1.7_UART_RX
RF1.9_UART_TX
RF1.3_UART_CTS
RF2.18_UART_RTS
6
RF2.4_JTAG_TMS
RF2.1_JTAG_TCK
RF2.19_JTAG_TDO
RF2.17_JTAG_TDI
RF2.15_RESET
RF_VDD1
2
1
PINROW_1X6
P404
PINROW_SMD_2X10_2.54MM
P412
2
4
6
8
10
PINROW_SMD_2X10_2.54MM
VDD_MEASURED
2
P411
PINROW_1X5
17
LV_BTN_SELECT
RF1.15
RF1.16_SPI_SCK
RF1.17
RF1.18_SPI_MOSI
RF1.20_SPI_MISO
RF2.5
RF2.6
RF2.8
RF2.10
RF2.11
P410
1
3
5
7
9
C_0603
1
VDD_SENSE
PINROW_SMD_2X5_1.27MM
P407
RF1.13
LV_LCD_RESET
RF1.2
RF1.4
RF1.5
RF1.6
RF1.8
RF1.10
RF1.11
RF1.12
RF1.13
RF1.14
C_0805
LV_BTN_LEFT
1
P405
P406
TP10
RF_VDD2
LO_VDD
Testpoint_Circle_40mils
R502
R_0R15_0603_F
1
VDD_MEASURED
2
1
2
1
2
OUT
GND
3
C_100N_0402_X5R_K_10
C508
U504
INA216A3
1.6M
1.6M
C_100N_0402_X5R_K_10
C507
R1
R2
INA216
IN-
2
RESET
TP11
1
2
TP20
4
CURMEAS_OUTPUT
TESTPIN_SMALL
TESTPIN_SMALL
Rshunt = 0.15 Ohm
Gain = 100
Vin = Ishunt x Rshunt
Vout = Vin x Gain
S606
PUSH_BUTTON_SKRAAK
12
2
IN+
1
1
C_100N_0402_X5R_K_10
C404
VDD_SENSE
C_100N_0402_X5R_K_10
C403
2
1
J503
PINROW_SMD_1X2_2.54MM
34
Saturation point for INA216
----------------------------Vout_max = LO_VDD (2.1V to 3.6V)
Vin_max = LO_VDD / 100 = 21mV to 36mV
Ishunt_max = 140mA to 240mA
LV_BTN_RESET
Copyright © 2017, Texas Instruments Incorporated
Figure 31. SmartRF06EB - EVM Interfaces/Level Shifters
34
Schematics
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
SmartRF06EB 1.2.1
www.ti.com
BATTERIES
VBAT
1
BAT54J
TP17
2
L501
1
1
2
1
2
2
L_2U2_0805_N_LQM21
3
3
R11
R_0_0402_3PORT_2-3
1
2
1
SW
VIN
Testpoint_Circle_40mils
V_UNREG
TPS63031
1
2
10 FB
9 GND
1
8 VINA
7 PS
3
6 EN
5
VOUT
L2
PGND
L1
VIN
Thermal
2
4
P3.3V
2
1
L502
L_2U2_0805_N_LQM21
1
U502 11
C504
C_2U2_0402_X5R_M_6P3VDC
2
BATTERY or
EXTERNAL
LV_3.3V_EN
BUCK (2.1V)
MAIN ON/OFF SWITCH
C503
C_2U2_0402_X5R_M_6P3VDC
1
STAT
GND
U501
C502
VOUT
ON/BYP
4
C_2U2_0402_X5R_M_6P3VDC
J501
2
6
5
2
REGULATOR
BYPASS
JUMPER
V_UNREG
V_UNREG
P2.1V
C501
+
3
TP18
Testpoint_Circle_40mils
TPS62730
C_2U2_0402_X5R_M_6P3VDC
2 1
R501
R_47K_0402_F
1
1
J502
B502
B503
+
CONNECTOR FOR
EXTERNAL POWER
1
2
2
V_UNREG
PINROW_SMD_1X2_2.54MM
2
1
V_UNREG
PINROW_SMD_1X2_2.54MM
B501
D3
+
CR2032_SOCKET
1XAAA_KEYSTONE
1XAAA_KEYSTONE
BATTERY REGULATORS
2
BUCK/BOOST (3.3V)
BATTERY or
EXTERNAL
ON
OFF
VBUS
2.1V
REG
VBAT
3.3V
REG
V_UNREG
USB (5V)
1
2
3
6
5
4
S501
SMD_SWITCH_DPDT
POWER SELECT SWITCH
V_USB
POWERED from BATTERY or
External Power Supply
3.3V FOR HV PERIPHERALS
LO_VDD
HI_VDD
USB
SMD_SWITCH_DPDT
S502
U601
P3.3V
TPS22902
2
3
1
5
4
6
P2.1V
Software controlled switch
for enabling the "High Voltage"
domain for board peripherals.
2
4
VIN
VOUT
ON
GND
1
3
R403
P3.3VXDS
P3.3VXDS
U2
TPS73533
2
NC
4
EN
TPS73533
NR
GND
1
2
3
GND
8
7
1
2
POWERED from USB
(XDS100v3)
2.1V FOR EM and LV PERIPHERALS
1
2
TP1
Testpoint_Circle_40mils
2
5
VOUT
C1
C_100N_0402_X5R_K_10
1
TP2
VIN
C2
C_18N_0603_X7R_J_50
1
C7
C_4U7_0603_X5R_K_6
6
Testpoint_Circle_40mils
USB TO 3.3V
V_USB
C10
C_100N_0402_X5R_K_10
2
XDS 3.3V
R_10K_0402_F
XDS100v3 VOLTAGE REGULATORS
1
LV_3.3V_EN
P3.3VXDS
USB TO 1.5V (FPGA)
1
2
1
SUSPEND
2
3
VIN
GND
EN
VOUT
TLV70015
NC4
5
4
C33
C_100N_0402_X5R_K_10
TP19
U5
TLV70015
Testpoint_Circle_40mils
+1.5V
2
R32
R_10K_0402_F
P3.3VXDS
1
C32
C_100N_0402_X5R_K_10
V_USB
1
2
Copyright © 2017, Texas Instruments Incorporated
Figure 32. SmartRF06EB - Power Supply
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Schematics
35
SmartRF06EB 1.2.1
www.ti.com
MICROSD
LEVEL SHIFTERS
HI_VDD
LO_VDD
N/A
CS
DI/MOSI
VDD
SCLK
GND
DO/MISO
N/A
MicroSD
SPI-Mode
1
C405
C_100N_0402_X5R_K_10
J601
MICROSD-SPI
HI_VDD
1
2
C406
C_100N_0402_X5R_K_10
2
LO_VDD
1
2
HI_VDD
HV_SDCARD_CS
HV_SPI_MOSI
3
U401
SN74AVC4T245
4
5
1
HV_SPI_SCK
6
VCCA
2
7
HV_SPI_MISO
1DIR
2DIR
1A1
1A2
2A1
2A2
GND
3
8
4
LV_SPI_SCK
LV_SPI_MOSI
LV_SPI_MISO
HI_VDD
5
6
7
8
1
VCCB
1OE
2OE
1B1
1B2
2B1
2B2
GND
C613
C_100N_0402_X5R_K_10
LO_VDD
2
16
15 LV_3.3V_EN
14 LV_SDCARD_CS
13 HV_SPI_SCK
12 HV_SPI_MOSI
11 HV_SPI_MISO
10
9
HI_VDD
LO_VDD LO_VDD LO_VDD
1
1
2
R_10K_0402_F
1
2
2
1
R602
2
1
R_10K_0402_F
R612
R_10K_0402_F
R601
C407
C_100N_0402_X5R_K_10
C408
C_100N_0402_X5R_K_10
2
LO_VDD
HI_VDD
U402
SN74AVC4T245
1
2
3
4
LV_LCD_RESET
LV_LCD_CS
LV_LCD_MODE
LV_SDCARD_CS
5
6
7
8
VCCA
VCCB
1OE
2OE
1B1
1B2
2B1
2B2
GND
1DIR
2DIR
1A1
1A2
2A1
2A2
GND
16
15 LV_3.3V_EN
14 LV_3.3V_EN
13 HV_LCD_RESET
12 HV_LCD_CS
11 HV_LCD_MODE
10 HV_SDCARD_CS
9
LEVEL SHIFTERS TRANSLATION :
2
U401:
U402:
LO
HI
1A1 --> 1B1
1A2 --> 1B2
2A1 1B2
2A1 --> 2B1
2A2 --> 2B2
1
R13
R_10K_0402_F
LO_VDD
LV_3.3V_EN
3
LV_3.3V_EN
LCD
HI_VDD
1
HV_SPI_SCK
TP14
Testpoint_Circle_40mils
Q2
2N7002F
HV_SPI_MOSI
TP15
Testpoint_Circle_40mils
2
HV_SPI_MISO
C604
C610
C_1U_0805_X7R_K_16
C_1U_0805_X7R_K_16
C_1U_0805_X7R_K_16
1
C601
2
C_1U_0402_X5R_K_6P3
1
C609
2
C_1U_0805_X7R_K_16
2
1
C608
2
C_1U_0805_X7R_K_16
3
V0
NC(C3-)
1
R_0_0603
R615
2
R_0_0603
R614
2
R_0_0603
R606
1
P4
SIP_SOCKET_SMD_1X3_2.54MM
1
P3
SIP_SOCKET_SMD_1X3_2.54MM
2
1
C607
2
3
2
1
3
2
1
LCD1
1
C606
2
C_1U_0805_X7R_K_16
4
V1
NC(C2-)
DOGM128W-6_NO_CON
1
C605
C_1U_0805_X7R_K_16
5
V2
1
2
C_1U_0805_X7R_K_16
6
V4
V3
7
VSS
CAP2N
CAP2P 8
9
1
NC(C1-)
NC(A1+)
NC(A2+)
HI_VDD
INSERT:
1 pc SIP_SOCKET_SMD_1X20_2.54MM
2 pc SIP_SOCKET_SMD_1X3_2.54MM
NC(A3+)
1
2
2
1
LCD
SIP_SOCKET_SMD_1X20_2.54MM
R_39_0603
R605
1
HI_VDD
R_39_0603
R604
2
2
R_39_0603
R603
1
HI_VDD
2
1
2
CAP1P
13
15
P2
HI_VDD
1
VOUT 12
16
VSS
VDD2 14
VDD
19
17
18
20
SI
A0
RST
CS1B
SCL
C603
HV_LCD_CS
2
C602
HV_LCD_RESET
10
HV_SPI_SCK
CAP1N
HV_SPI_MOSI
HV_LCD_MODE
CAP3P 11
C_1U_0805_X7R_K_16
TP16
Testpoint_Circle_40mils
Copyright © 2017, Texas Instruments Incorporated
Figure 33. SmartRF06EB - High Voltage Peripheral
AMBIENT LIGHT SENSOR
ACCELEROMETER
LED_EL19-21SRC
1
1
R_820_0402_G
R607
S602
PUSH_BUTTON_SKRAAK
12
C615
C_100N_0402_X5R_K_10
RECOMMENDED 2.3V-5.5V
LO_VDD
LV_BTN_RIGHT
Accelerometer
34
YELLOW
Needs from 1.62V-3.6V
S603
PUSH_BUTTON_SKRAAK
LV_BTN_SELECT
LV_SPI_MISO
LV_SPI_MOSI
LV_ACC_CS
2
1
D602
LV_LED_2
2
1
12
R_680_0402_G
R608
LED_EL19-21UYC_A2
34
LV_SPI_SCK
LV_BTN_UP
LV_ACC_PWR
GREEN
12
1
2
1
2
1
R_680_0402_G
R609
S605
PUSH_BUTTON_SKRAAK
12
GND
GND
VDD
LS601
Iout
4
2
10
12
U602
BMA250
SDO
VDDIO
SDx
VDD
BMA250
CSB
NC
3-AXIS
PS Accelerometer
INT1
SCx
INT2
GNDIO GND
8
LV_ALS_OUT
3
LV_ALS_PWR
1
2
3
7
LV_ACC_PWR
4
5
6
LV_ACC_INT1
LV_ACC_INT2
9
34
D603
LV_LED_3
LED_EL19-21SYGC
1
11
S604
PUSH_BUTTON_SKRAAK
1
2
LIGHT_SENSOR_SFH5711
2
2
2
R613
LO_VDD
1
LV_BTN_LEFT
34
C614
2
1
LV_LED_1
12
R_22K_0603_G
BUTTONS
S601
PUSH_BUTTON_SKRAAK
D601
C_100N_0402_X5R_K_10
LEDS
RED
LV_BTN_DOWN
C612
C_100N_0402_X5R_K_10
2
34
RED-ORANGE
2
1
D604
LV_LED_4
2
LED_EL19-21SURC
1
R_680_0402_G
R610
Copyright © 2017, Texas Instruments Incorporated
Figure 34. SmartRF06EB - Low Voltage Peripherals
36
Schematics
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Revision History
www.ti.com
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from A Revision (May 2012) to B Revision ...................................................................................................... Page
•
Added note of change in accelerometer. ............................................................................................... 5
SWRU321B – May 2012 – Revised March 2017
Submit Documentation Feedback
Copyright © 2012–2017, Texas Instruments Incorporated
Revision History
37
STANDARD TERMS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or
documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance
with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License
Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by
neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have
been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications
or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control
techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.
User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)
business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.
2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit
User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty
period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or
replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be
warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software
associated with the kit to determine whether to incorporate such items in a finished product and software developers to write
software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or
otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition
that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.
Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must
operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the
instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs
(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/
/www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
3.4 European Union
3.4.1
For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):
This is a class A product intended for use in environments other than domestic environments that are connected to a
low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measures.
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT
LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL
FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT
NOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE
SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BE
CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR
INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE
EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR
IMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLY
WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL
THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR
REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING,
OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF
USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI
MORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HAS
OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDED
HEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR IN
CONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAR
EVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE
CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号