SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
1.5-Gbps LVDS/LVPECL/CML-TO-CML TRANSLATOR/REPEATER
FEATURES
•
•
•
•
•
•
•
•
•
•
DESCRIPTION
Provides Level Translation From LVDS or
LVPECL to CML, Repeating From CML to CML
Signaling Rates(1) up to 1.5 Gbps
CML Compatible Output Directly Drives
Devices With 3.3-V, 2.5-V, or 1.8-V Supplies
Total Jitter < 70 ps
Low 100 ps (Max) Part-To-Part Skew
Wide Common-Mode Receiver Capability
Allows Direct Coupling of Input Signals
25 mV of Receiver Input Threshold Hysteresis
Over 0-V to 4-V Common-Mode Range
Propagation Delay Times, 800 ps Maximum
3.3-V Supply Operation
Available in SOIC and MSOP Packages
APPLICATIONS
•
•
•
•
•
Level Translation
622-MHz Central Office Clock Distribution
High-Speed Network Routing
Wireless Basestations
Low Jitter Clock Repeater (1)
(1)
The signaling rate of a line is the number of voltage
transitions that are made per second expressed in the units
bps (bits per second).
A
B
8
4
2
7
6
3
The VBB pin is an internally generated voltage supply
to allow operation with a single-ended LVPECL input.
For single-ended LVPECL input operation, the
unused differential input is connected to VBB as a
switching reference voltage. When used, decouple
VBB with a 0.01-µF capacitor and limit the current
sourcing or sinking to 400 µA. When not used, VBB
should be left open.
This device is characterized for operation from –40°C
to 85°C.
EYE PATTERN
FUNCTIONAL DIAGRAM
VCC
This high-speed translator/repeater is designed for
signaling rates up to 1.5 Gbps to support various
high-speed network routing applications. The driver
output is compatible with current-mode logic (CML)
levels, and directly drives 50-Ω or 25-Ω loads
connected to 1.8-V, 2.5-V, or 3.3-V nominal supplies.
The capability for direct connection to the loads may
eliminate the need for coupling capacitors. The
receiver input is compatible with LVDS (TIA/EIA-644),
LVPECL, and CML signaling levels. The receiver
tolerates a wide common-mode voltage range, and
may also be directly coupled to the signal source.
The internal data path from input to output is fully
differential for low noise generation and low
pulse-width distortion.
VBB
1.5 Gbps
223-1 PRBS
Y
Z
Vertical Scale = 500 mV/div
750 MHz
Horizontal Scale = 200 ps/div
VCC = 3.3 V, TA = 25°C, VID = 200 mV, VIC = 1.2 V, VTT = 3.3 V, RT = 50 Ω
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2002–TBD, Texas Instruments Incorporated
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
PART NUMBER
PART MARKING
PACKAGE
STATUS
CML100
SOIC
Production
NWB
MSOP
Production
SN65CML100D
SN65CML100DGK
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
UNIT
VCC
Supply voltage range (2)
IBB
Sink/source
–0.5 V to 4 V
±0.5 mA
Voltage range, (A, B, Y, Z)
Electrostatic
discharge
0 V to 4.3 V
Human Body Model
Charged-Device
(3)
Model (4)
A, B, Y, Z, and GND
±5 kV
All pins
±2 kV
±1500 V
All pins
Continuous power dissipation
Tstg
See Dissipation Rating Table
Storage temperature range
–65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
(1)
(2)
(3)
(4)
260°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values, except differential I/O bus voltages, are with respect to network ground terminal.
Tested in accordance with JEDEC Standard 22, Test Method A114-A.7.
Tested in accordance with JEDEC Standard 22, Test Method C101.
RECOMMENDED OPERATING CONDITIONS
VCC
MIN
NOM
MAX
3
3.3
3.6
3.3-V nominal supply at terminator
3
3.3
3.6
2.5-V nominal supply at terminator
2.375
2.5
2.625
1.8-V nominal supply at terminator
1.7
1.9
V
0.1
1
V
Supply voltage
VTT
Terminator supply voltage
|VID|
Magnitude of differential input voltage
Input voltage (any combination of common-mode or input signals)
VBB
Output current
TA
Operating free-air temperature
0
–40
UNIT
4
V
µA
85
°C
2
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR (1)
ABOVE TA = 25°C
TA = 85°C
POWER RATING
DGK
425 mW
3.4 mW/°C
221 mW
D
725 mW
5.8 mW/°C
377 mW
This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow.
Submit Documentation Feedback
V
400
PACKAGE DISSIPATION RATINGS
(1)
V
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
DEVICE CHARACTERISTICS
PARAMETER
ICC
Supply current, device only
VBB
Switching reference voltage (1)
(1)
MIN NOM
MAX
UNIT
9
12
mA
1890 1950
2010
mV
VBB parameter varies 1:1 with VCC
INPUT ELECTRICAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
Positive-going differential input voltage
threshold
VIT+
mV
–100
VID(HYS) Differential input voltage hysteresis,VIT+ – VIT–
25
VI = 0 V or 2.4 V, Second input at 1.2 V
II
Input current (A or B inputs)
II(OFF)
Power off input current (A or B inputs)
–20
Input offset current (|IIA - IIB|)
Ci
Differential input capacitance
(1)
mV
20
VI = 4 V, Second input at 1.2 V
33
VCC = 1.5 V, VI = 0 V or 2.4 V,
Second input at 1.2 V
–20
20
VCC = 1.5 V, VI = 4 V, Second input at 1.2 V
IIO
UNIT
100
See Figure 1 and Table 1
Negative-going differential input voltage
threshold
VIT-
MIN TYP (1) MAX
TEST CONDITIONS
µA
µA
33
VIA = VIB, 0 ≤ VIA ≤ 4 V
–6
6
VI = 0.4 sin (4E6πt) + 0.5 V
3
VCC = 0 V
3
µA
pF
All typical values are at 25°C and with a 3.3-V supply.
OUTPUT ELECTRICAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
voltage (2)
VOH
Output high
VOL
Output low voltage (2)
|VOD|
Differential output voltage magnitude
VOH
Output high voltage (3)
VOL
Output low voltage (3)
|VOD|
Differential output voltage magnitude
VOH
Output high voltage (2)
VOL
Output low voltage (2)
|VOD|
Differential output voltage magnitude
VOH
Output high voltage (3)
VOL
Output low voltage (3)
|VOD|
Differential output voltage magnitude
Co
Differential output capacitance
(1)
(2)
(3)
TEST CONDITIONS
RT = 50 Ω, VTT = 3 V to 3.6 V or VTT = 2.5 V ±5%,
See Figure 2
RT = 25 Ω, VTT = 3 V to 3.6 V or VTT = 2.5 V ±5%,
See Figure 2
RT = 50 Ω, VTT = 1.8 V ±5%, See Figure 2
RT = 25 Ω, VTT = 1.8 V ±5%, See Figure 2
MIN
TYP (1)
MAX
VTT–60
VTT–10
VTT
mV
VTT–1100
VTT–800
VTT–640
mV
640
780
1000
mV
VTT–60
VTT–10
VTT
mV
VTT–550
VTT–400
VTT–320
mV
320
390
500
mV
VTT–170
VTT–10
VTT
mV
VTT–1100
VTT–800
VTT–640
mV
570
780
1000
mV
VTT–85
VTT–10
VTT
mV
VTT–500
VTT–400
VTT–320
mV
285
390
500
mV
VI = 0.4 sin (4E6πt) + 0.5 V
3
VCC = 0 V
3
UNIT
pF
All typical values are at 25°C and with a 3.3-V supply.
Outputs are terminated through 50-Ω resistors to VTT, CML level specifications are referenced to VTT and tracks 1:1 with variation of
VTT.
Outputs are terminated through 25-Ω resistors to VTT; CML level specifications are referenced to VTT and tracks 1:1 with variation of
VTT.
Submit Documentation Feedback
3
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
SWITCHING CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
tPLH
Propagation delay time, low-to-high-level output
tPHL
Propagation delay time, high-to-low-level output
tr
Differential output signal rise time (20%–80%)
tf
Differential output signal fall time (20%–80%)
(|tPHL– tPLH|) (2)
skew (3)
RT = 50 Ω or RT = 25 Ω, SeeFigure 4
tsk(p)
Pulse skew
tsk(pp)
Part-to-part
tjit(per)
Period jitter, rms (1 standard deviation) (4)
750 MHz clock input (5)
tjit(cc)
Cycle-to-cycle jitter (peak)(4)
750 MHz clock input (6)
jitter(4)
tjit(pp)
Peak-to-peak
tjit(det)
Deterministic jitter, peak-to-peak(4)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
4
MIN
NOM (
MAX
UNIT
250
800
ps
250
800
ps
300
ps
300
ps
1)
0
50
ps
100
ps
1
5
ps
8
27
ps
input (7)
30
70
ps
1.5 Gbps 27–1 PRBS input (8)
25
65
ps
VID = 0.2 V
1.5 Gbps
223-1
PRBS
All typical values are at 25°C and with a 3.3-V supply.
tsk(p) is the magnitude of the time difference between the tPLH and tPHL.
tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both
devicesoperate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
Jitter parameters are ensured by design and characterization. Measurements are made with a Tektronix TDS6604 oscilloscope
runningTektronix TDSJIT3 software. Agilent E4862B stimulus system jitter 2 ps tjit(per), 16 ps tjit(cc), 25 ps tjit(pp), and 10 ps tjit(det) has
beensubtracted from the values.
VID = 200 mV, 50% duty cycle, VIC = 1.2 V, tr = tf ≤ 25 ns (20% to 80%), measured over 1000 samples.
VID = 200 mV, 50% duty cycle, VIC = 1.2 V, tr = tf ≤ 25 ns (20% to 80%).
VID = 200 mV, VIC = 1.2 V, tr = tf ≤ 0.25 ns (20% to 80%), measured over 100k samples.
VID = 200 mV, VIC = 1.2 V, tr = tf ≤ 0.25 ns (20% to 80%). Deterministic jitter is sum of pattern dependent jitter and pulse width distortion.
Submit Documentation Feedback
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
PARAMETER MEASUREMENT INFORMATION
IIA
A
Y
B
Z
VID
VIA+VIB
VIC
VOD
VIA
VIB
2
VOY
VOY+VOZ
VOZ
IIB
2
Figure 1. Voltage and Current Definitions
Table 1. Maximum Receiver Input Voltage Threshold
APPLIED VOLTAGES
(1)
RESULTING DIFFERENTIAL
INPUT VOLTAGE
RESULTING COMMONMODE INPUT VOLTAGE
VID
VIC
OUTPUT (1)
VIA
VIB
1.25 V
1.15 V
100 mV
1.2 V
1.15 V
1.25 V
–100 mV
1.2 V
L
4.0 V
3.9 V
100 mV
3.95 V
H
3.9 V
4. 0 V
–100 mV
3.95 V
L
0.1 V
0.0 V
100 mV
0.5 V
H
0.0 V
0.1 V
–100 mV
0.5 V
L
1.7 V
0.7 V
1000 mV
1.2 V
H
0.7 V
1.7 V
–1000 mV
1.2 V
L
4.0 V
3.0 V
1000 mV
3.5 V
H
3.0 V
4.0 V
–1000 mV
3.5 V
L
1.0 V
0.0 V
1000 mV
0.5 V
H
0.0 V
1.0 V
–1000 mV
0.5 V
L
H
H = high level, L = low level
Y
RT
VOD
RT
Z
VOY
+
_
VTT
VOZ
Figure 2. Output Voltage Test Circuit
Y
VOD
Driver Device
Receiver Device
Z
RT1
RT2
RT1 = RT2 = RT
VTT
Figure 3. Typical Termination for Output Driver
Submit Documentation Feedback
5
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
RT1
A
Y
1 pF
VID
VIA
B
VOY
Z
VIB
VTT
RT2
VIA
1.4 V
VIB
1V
VID
0.4 V
0V
-0.4 V
RT1 = RT2 = RT
VOZ
tPHL
tPLH
100%
0V
80%
VOY - VOZ
20%
tf
0%
tr
NOTE: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 0.25 ns, pulse repetition rate
(PRR) = 50 Mpps, pulse width = 10 ± 0.2 ns. CL includes instrumentation and fixture capacitance within 0,06 mm of
the D.U.T.Measurement equipment provides a bandwidth of 5 GHz minimum.
Figure 4. Timing Test Circuit and Waveforms
PIN ASSIGNMENTS
D AND DGK PACKAGE
(TOP VIEW)
NC
A
B
VBB
1
8
VCC
2
7
Y
3
6
Z
4
5
GND
Table 2. PIN DESCRIPTIONS
PIN
FUNCTION
A, B
Differential inputs
Y, Z
Differential outputs
VBB
Reference voltage output
VCC
Power supply
GND
Ground
NC
No connect
Table 3. FUNCTION TABLE
DIFFERENTIAL INPUT
(1)
6
OUTPUTS (1)
VID = VA– VB
Y
Z
VID ≥ 100 mV
H
L
–100 mV < VID < 100 mV
?
?
VID ≤ –100 mV
L
H
Open
?
?
H = high level, L = low level, ? = intermediate
Submit Documentation Feedback
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
EQUIVALENT INPUT AND OUTPUT SCHEMATIC DIAGRAMS
OUTPUT
INPUT
VCC
VCC
A
VCC
VCC
B
Y
Z
7V
7V
7V
7V
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
12
10
10
8
6
VCC = 3.3 V,
TA = 25°C,
VIC = 1.2 V,
VID = 200 mV,
RT = 50 Ω,
VTT = 2.5 V
4
2
0
1000
8
6
VCC = 3.3 V,
VIC = 1.2 V,
VID = 200 mV,
f = 750 MHz,
RT = 50 Ω,
VTT = 2.5 V
4
2
0
0
250
500
750
−40
1000
−20
0
20
40
60
80
900
VCC = 3.3 V,
TA = 25°C,
VIC = 1.2 V,
VID = 200 mV,
RT = 50 Ω
VTT = 3.3 V
800
700
VTT = 1.7 V
VTT = 2.5 V
600
500
100
100
TA − Free-Air Temperature − °C
f − Frequency − MHz
200
300 400 500 600
f − Frequency − MHz
700
Figure 5.
Figure 6.
Figure 7.
DIFFERENTIAL OUTPUT VOLTAGE
vs
FREQUENCY
PROPAGATION DELAY TIME
vs
COMMON-MODE INPUT VOLTAGE
PROPAGATION DELAY TIME
vs
FREE-AIR TEMPERATURE
VTT = 3.3 V
400
VTT = 2.5 V
350
VTT = 1.7 V
300
250
100
VCC = 3.3 V,
TA = 25°C,
VID = 200 mV
f = 25 MHz,
RT = 50 Ω,
VTT = 2.5 V
475
450
t pd − Propagation Delay Time − ps
t pd − Propagation Delay Time − ps
450
VCC = 3.3 V,
TA = 25°C,
VIC = 1.2 V,
VID = 200 mV,
RT = 25 Ω
tPLH
425
tPHL
400
375
350
200
300 400 500 600
f − Frequency − MHz
Figure 8.
700
800
800
500
500
500
V OD − Differential Output Voltage − mV
DIFFERENTIAL OUTPUT VOLTAGE
vs
FREQUENCY
V OD − Differential Output Voltage − mV
12
I CC − Supply Current − mA
I CC − Supply Current − mA
SUPPLY CURRENT
vs
FREQUENCY
0
0.5
1
1.5
2
2.5
3
3.5
VIC − Common Mode Input Voltage − V
Figure 9.
Submit Documentation Feedback
4
475
450
425
VCC = 3.3 V,
VIC = 1.2 V,
VID = 200 mV,
f = 25 MHz,
RT = 50 Ω,
VTT = 2.5 V
tPHL
tPLH
400
375
350
−40
−20
0
20
40
60
80
100
TA− Free-Air Temperature − °C
Figure 10.
7
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
TYPICAL CHARACTERISTICS (continued)
PROPAGATION DELAY TIME
vs
FREE-AIR TEMPERATURE
PEAK-TO-PEAK JITTER
vs
FREQUENCY
30
625
600
575
25
tPHL
550
35
VCC = 3.3 V,
TA = 25°C,
VIC = 1.2 V,
RT = 50 Ω,
VTT = 2.5 V,
Input = Clock
tPLH
20
15
VID = 0.3 V
10
VID = 0.5 V
5
525
500
−40
−20
0
20
40
60
80
VID = 0.8 V
25
20
VID = 0.5 V
15
10
VID = 0.3 V
5
0
100
100
VCC = 3.3 V,
TA = 25°C,
VIC = 1.2 V,
VID = 0.8 V
RT = 50 Ω,
VTT = 2.5 V
Input = 223−1 PRBS
30
Peak-To-Peak Jitter − ps
VCC = 3.3 V,
VIC = 1.2 V,
VID = 200 mV,
RT = 50 Ω,
VTT = 1.7 V,
f = 25 MHz
Peak-To-Peak Jitter − ps
200
300
400
500
600
700
0
200
800
400
f − Frequency − MHz
TA− Free-Air Temperature − °C
600
800
1000 1200 1400 1600
Data Rate − Mbps
Figure 11.
Figure 12.
Figure 13.
PEAK-TO-PEAK JITTER
vs
COMMON MODE INPUT VOLTAGE
PEAK-TO-PEAK JITTER
vs
COMMON MODE INPUT VOLTAGE
PEAK-TO-PEAK JITTER
vs
DATA RATE
60
30
VCC = 3.3 V,
TA = 25°C,
RT = 50 Ω,
VTT = 2.5 V
Input = Clock
20
50
Peak-To-Peak Jitter − ps
25
VID = 0.8 V
15
VID = 0.5 V
10
0
0.5
1
1.5
2
2.5
3
40
3.5
4
VID = 0.5 V
30
VID = 0.8 V
20
VIC − Common Mode Input Voltage − V
Figure 14.
0.5 1
1.5 2
2.5 3
3.5
VIC − Common Mode Input Voltage − V
25
VTT = 1.7 V
20
15
VTT = 2.5 V
10
VTT = 3.3 V
5
200
0
0
VCC = 3.3 V, TA = 25°C,
VIC = 1.2 V, |VID| = 200 mV,
Input = 223−1 PRBS, RT = 50 Ω
VID = 0.3 V
10
VID = 0.3 V
5
0
30
VCC = 3.3 V,
TA = 25°C,
RT = 50 Ω,
VTT = 2.5 V
Input = 223−1 PRBS
Peak-To-Peak Jitter − ps
t pd − Propagation Delay Time − ps
650
Peak-To-Peak Jitter − ps
PEAK-TO-PEAK JITTER
vs
DATA RATE
4
400
600
800
1000 1200 1400 1600
Data Rate − Mbps
Figure 15.
Figure 16.
PEAK-TO-PEAK JITTER
vs
DATA RATE
Peak-To-Peak Jitter − ps
25
20
15
VCC = 3.3 V, TA = 25°C,
VIC = 1.2 V,
VID = 200 mV,
Input = 223−1 PRBS,
RT = 25 Ω
1.5 Gbps
223-1 PRBS
VTT = 1.7 V
Vertical Scale = 250 mV/div
VTT = 2.5 V
10
750 MHz
VTT = 3.3 V
5
200
400
600
800
Horizontal Scale = 200 ps/div
1000 1200 1400 1600
Data Rate − Mbps
VCC = 3.3 V, TA = 25°C, VID = 200 mV, VIC = 1.2 V, VTT = 3.3 V, RT = 25 Ω
Figure 17.
8
Figure 18.
Submit Documentation Feedback
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
TYPICAL CHARACTERISTICS (continued)
1.5 Gbps
223-1 PRBS
1.5 Gbps
223-1 PRBS
Vertical Scale = 500 mV/div
Vertical Scale = 250 mV/div
750 MHz
750 MHz
Horizontal Scale = 200 ps/div
VCC = 3.3 V, TA = 25°C, VID = 200 mV, VIC = 1.2 V, VTT = 2.5 V, RT = 50 Ω
Horizontal Scale = 200 ps/div
VCC = 3.3 V, TA = 25°C, VID = 200 mV, VIC = 1.2 V, VTT = 2.5 V, RT = 25 Ω
Figure 19.
Figure 20.
1.5 Gbps
223-1 PRBS
1.5 Gbps
223-1 PRBS
Vertical Scale = 500 mV/div
Vertical Scale = 250 mV/div
750 MHz
750 MHz
Horizoontal Scale = 200 ps/div
Horizoontal Scale = 200 ps/div
VCC = 3.3 V, TA = 25°C, VIC = 1.2 V, VID = 200 mV, VTT = 1.7 V, RT = 50 Ω
VCC = 3.3 V, TA = 25°C, VIC = 1.2 V, VID = 200 mV, VTT = 1.7 V, RT = 25 Ω
Figure 21.
Figure 22.
Submit Documentation Feedback
9
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
TYPICAL CHARACTERISTICS (continued)
Power Supply 1
+
3.3 V
-
Power Supply 2
+
VTT
J3
DUT
GND
J2
EVM
GND
J1
VCC
J4
J5
J6
100 Ω
J7
50 Ω
DUT
Pattern
Generator
Matched
Cables
SMA to SMA
50 Ω
Matched
Cables
SMA to SMA
EVM
Oscilloscope
Figure 23. Jitter Setup Connections for SN65CML100
10
Submit Documentation Feedback
SN65CML100
www.ti.com
SLLS547 – NOVEMBER 2002
APPLICATION INFORMATION
For single-ended input conditions, the unused differential input is connected to VBB as a switching reference
voltage. When VBB is used, decouple VBB via a 0.01-µF capacitor and limit the current sourcing or sinking to 0.4
mA. When not used, VBB should be left open.
TYPICAL APPLICATION CIRCUITS (ECL, PECL, LVDS, etc.)
50 Ω
3.3 V or 5 V
3.3 V
SN65CML100
A
ECL
B
50 Ω
50 Ω
50 Ω
VTT = VCC -2 V
VTT
Figure 24. Low-Voltage Positive Emitter-Coupled Logic (LVPECL)
50 Ω
3.3 V
3.3 V
SN65CML100
A
CML
B
50 Ω
VTT
Figure 25. Current-Mode Logic (CML)
3.3 V
3.3 V
50 Ω
SN65CML100
A
ECL
VBB
B
50 Ω
VTT
VTT = VCC -2 V
Figure 26. Single-Ended (LVPECL)
3.3 V or 5 V
50 Ω
3.3 V
SN65CML100
A
100 Ω
LVDS
B
50 Ω
Figure 27. Low-Voltage Differential Signaling (LVDS)
Submit Documentation Feedback
11
PACKAGE OPTION ADDENDUM
www.ti.com
13-Jul-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
SN65CML100D
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
CML100
Samples
SN65CML100DGK
ACTIVE
VSSOP
DGK
8
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
NWB
Samples
SN65CML100DGKG4
ACTIVE
VSSOP
DGK
8
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
NWB
Samples
SN65CML100DGKR
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
NWB
Samples
SN65CML100DR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
CML100
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of