Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
SN65HVD7x 3.3-V Supply RS-485 With IEC ESD protection
1 Features
2 Applications
•
•
•
•
1
•
•
•
•
•
•
•
•
Small-size VSSOP Packages Save Board Space,
or SOIC for Drop-in Compatibility
Bus I/O Protection
– >±15 kV HBM Protection
– >±12 kV IEC 61000-4-2 Contact Discharge
– >±4 kV IEC 61000-4-4 Fast Transient Burst
Extended Industrial Temperature Range
–40°C to 125°C
Large Receiver Hysteresis (80 mV) for Noise
Rejection
Low Unit-Loading Allows Over 200 Connected
Nodes
Low Power Consumption
– Low Standby Supply Current: < 2 µA
– ICC < 1 mA Quiescent During Operation
5-V Tolerant Logic Inputs Compatible With
3.3-V or 5-V Controllers
Signaling Rate Options Optimized for:
250 kbps, 20 Mbps, 50 Mbps
Glitch Free Power-Up and Power-Down Bus
Inputs and Outputs
Factory Automation
Telecommunications Infrastructure
Motion Control
3 Description
These devices have robust 3.3-V drivers and
receivers in a small package for demanding industrial
applications. The bus pins are robust to ESD events
with high levels of protection to Human-Body Model
and IEC Contact Discharge specifications.
Each of these devices combines a differential driver
and a differential receiver which operate from a single
3.3-V power supply. The driver differential outputs
and the receiver differential inputs are connected
internally to form a bus port suitable for half-duplex
(two-wire bus) communication. These devices feature
a wide common-mode voltage range making the
devices suitable for multi-point applications over long
cable runs. These devices are characterized from
–40°C to 125°C.
Device Information(1)
PART NUMBER
PACKAGE
SOIC (8)
SN65HVD72,
SN65HVD75,
SN65HVD78
BODY SIZE (NOM)
4.91 mm × 3.90 mm
VSSOP (8)
3.00 mm × 3.00 mm
VSON (8)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application Diagram
R
R
RE
B
DE
D
R
A
R
A
RT
RT
D
A
R
B
A
D
R RE DE D
R
RE
B
DE
D
B
D
D
R RE DE D
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION
DATA.
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
4
4
5
7.1
7.2
7.3
7.4
7.5
7.6
7.7
5
5
5
6
6
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Power Dissipation .....................................................
Switching Characteristics: 250 kbps Device
(SN65HVD72) Bit Time ≥ 4 µs...................................
7.8 Switching Characteristics: 20 Mbps Device
(SN65HVD75) Bit Time ≥50 ns ..................................
7.9 Switching Characteristics: 50 Mbps Device
(SN65HVD78) Bit Time ≥20 ns ..................................
7.10 Typical Characteristics ............................................
8
9
7
8
8
9
Parameter Measurement Information ................ 11
Detailed Description ............................................ 15
9.1
9.2
9.3
9.4
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
15
15
15
15
10 Application and Implementation........................ 17
10.1 Application Information.......................................... 17
10.2 Typical Application ................................................ 18
11 Power Supply Recommendations ..................... 24
12 Layout................................................................... 25
12.1 Layout Guidelines ................................................. 25
12.2 Layout Example .................................................... 25
13 Device and Documentation Support ................. 26
13.1
13.2
13.3
13.4
13.5
13.6
13.7
Device Support......................................................
Documentation Support ........................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
26
26
26
26
26
26
26
14 Mechanical, Packaging, and Orderable
Information ........................................................... 27
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision G (Januarly 2019) to Revision H
Page
•
Changed the Pin Configuration images.................................................................................................................................. 4
•
Changed Supply voltage, VCC MAX value From = 3.6 V To: 5 V in the Absolute Maximum Ratings table ........................... 5
•
Deleted "or R pin" for VCC in the Absolute Maximum Ratings ............................................................................................... 5
•
Added reliability note to VCC in the Recommended Operating Conditions table .................................................................... 5
Changes from Revision F (December 2016) to Revision G
Page
•
Changed From: Supply voltage, VCC MAX value = 5.5 V To: Supply voltage, VCC or R pin MAX value = 3.6 V in the
Absolute Maximum Ratings table ........................................................................................................................................... 5
•
Changed From: Input voltage at any logic pin To: Voltage at D, DE, or RE in the Absolute Maximum Ratings table .......... 5
Changes from Revision E (September 2016) to Revision F
•
Page
Changed pin A From: 7 To: 6, and pin B From: 6 To: 7 in Figure 26 .................................................................................. 22
Changes from Revision D (July 2015) to Revision E
•
2
Page
Added new Feature: Glitch Free Power-Up and Power-Down Bus Inputs and Outputs ....................................................... 1
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
Changes from Revision C (September 2013) to Revision D
•
Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision B (June 2012) to Revision C
Page
•
Deleted Feature: > ±12kV IEC61000-4-2 Air-Gap Discharge ................................................................................................ 1
•
Added Footnote 2 to the Absolute Maximum Ratings table ................................................................................................... 5
•
Changed the Switching Characteristics conditions statement From: 250 kbps devices (SN65HVD70, 71, 72) bit time
> 4 µs To: 250 kbps device (SN65HVD72) bit time ≥ 4 µs .................................................................................................... 7
•
Changed the Switching Characteristics conditions statement From: 250 kbps devices (SN65HVD73, 74, 75) bit time
> 50 ns To: 250 kbps device (SN65HVD75) bit time ≥ 50 ns ................................................................................................ 8
•
Changed the Switching Characteristics conditions statement From: 250 kbps devices (SN65HVD76, 77, 78)bit time
> 20 ns To: 250 kbps device (SN65HVD78) bit time ≥ 20 ns ............................................................................................... 8
•
Added note : RL = 54 Ω to Figure 6, Figure 7, and Figure 8 .................................................................................................. 9
•
Added the DGK package to the SN65HVD72, 75, 78 Logic Diagram ................................................................................. 15
•
Replaced the LOW-POWER STANDBY MODE section ...................................................................................................... 19
•
Added text to the Transient Protection section..................................................................................................................... 20
Changes from Revision A (May 2012) to Revision B
Page
•
Added the SON-8 package and Nodes column to Device Comparison Table,...................................................................... 4
•
Changed the Voltage range at A or B Inputs MIN value From: –8 V To: –13 V in the Absolute Maximum Ratings table .... 5
•
Added footnote for free-air temperature to the Recommended Operating Conditions table.................................................. 5
•
Changed the Bus input current (disabled driver) TYP values for HVD78 VI = 12 V From: 150 To: 240 and VI = –7 V
From: –120 To: –180 .............................................................................................................................................................. 7
•
Changed, Thermal Information............................................................................................................................................... 7
•
Changed, Thermal Characteristics ......................................................................................................................................... 7
•
Added TYP values to the Switching Characteristics table...................................................................................................... 8
•
Added TYP values to the Switching Characteristics table...................................................................................................... 8
•
Changed the SN65HVD72, 75, 78 Logic Diagram ............................................................................................................... 15
•
Added section: LOW-POWER STANDBY MODE ................................................................................................................ 19
Changes from Original (March 2012) to Revision A
Page
•
Added VALUEs to the Thermal Characteristics table in the DEVICE INFORMATION section. ........................................... 7
•
Changed the Switching Characteristics condition statement From: 15 kbps devices (SN65HVD73, 74, 75) bit time >
65 ns To: 20 Mbps devices (SN65HVD73, 74, 75) bit time > 50 ns ...................................................................................... 8
•
Changed the Switching Characteristics condition statement From: 50 kbps devices (SN65HVD76, 77, 78) bit time >
20 ns To: 50 Mbps devices (SN65HVD76, 77, 78) bit time > 20 ns ...................................................................................... 8
•
Added Figure 4 to Typical Characteristics. ............................................................................................................................ 9
•
Added Figure 5 to Typical Characteristics. ............................................................................................................................ 9
•
Added Figure 6 to Typical Characteristics. ............................................................................................................................ 9
•
Added Figure 7 to Typical Characteristics. ............................................................................................................................ 9
•
Added Figure 8 to Typical Characteristics. ............................................................................................................................ 9
•
Added Figure 9 to Typical Characteristics. ............................................................................................................................ 9
•
Added Application Information section to data sheet. .......................................................................................................... 17
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
3
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
5 Device Comparison Table
PART NUMBER
SIGNALING RATE
SN65HVD72
Up to 250 kbps
SN65HVD75
Up to 20 Mbps
SN65HVD78
Up to 50 Mbps
NODES
DUPLEX
ENABLES
Half
DE, RE
213
96
6 Pin Configuration and Functions
D Package
8-Pin SOIC
Top View
DGK Package
8-Pin VSSOP
Top View
R
1
8
VCC
RE
2
7
B
DE
3
6
A
D
4
5
GND
R
1
8
VCC
RE
2
7
B
DE
3
6
A
D
4
5
GND
No t to scale
No t to scale
DRB Package
8-Pin VSON
Top View
R
1
8
VCC
RE
2
7
B
DE
3
6
A
D
4
5
GND
No t to scale
Pin Functions
PIN
NAME
NUMBER
TYPE
DESCRIPTION
A
6
Bus I/O
Driver output or receiver input (complementary to B)
B
7
Bus I/O
Driver output or receiver input (complementary to A)
D
4
Digital input
Driver data input
DE
3
Digital input
Active-high driver enable
GND
5
Reference potential
Local device ground
R
1
Digital output
Receive data output
RE
2
Digital input
VCC
8
Supply
4
Submit Documentation Feedback
Active-low receiver enable
3-V to 3.6-V supply
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
7 Specifications
7.1 Absolute Maximum Ratings
over recommended operating range (unless otherwise specified)
(1)
MIN
MAX
–0.5
5
Voltage at A or B inputs
–13
16.5
Voltage at D, DE, or RE
–0.3
5.7
Voltage input, transient pulse, A and B, through 100 Ω
–100
100
Receiver output current
–24
Supply voltage, VCC
Junction temperature, TJ
V
24
mA
170
°C
Continuous total power dissipation
See Power Dissipation
Storage temperature, Tstg
–65
(1)
UNIT
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD Ratings
VALUE
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins
V(ESD)
(1)
(2)
(3)
Electrostatic
discharge
(1)
±8000
Charged device model (CDM), per JEDEC specification JESD22-C101 or
ANSI/ESDA/JEDEC JS-002, all pins (2)
±1500
JEDEC Standard 22, Test Method A115 (Machine Model), all pins
±300
IEC 61000-4-2 ESD (Air-Gap Discharge), bus pins and GND
UNIT
(3)
V
±12000
IEC 61000-4-2 ESD (Contact Discharge), bus pins and GND
±12000
IEC 61000-4-4 EFT (Fast transient or burst) bus pins and GND
±4000
IEC 60749-26 ESD (Human Body Model), bus pins and GND
±15000
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
By inference from contact discharge results, see Application and Implementation.
7.3 Recommended Operating Conditions
MIN
NOM
MAX
3
3.3
3.6
V
–7
12
V
High-level input voltage (driver, driver enable, and receiver enable inputs)
2
VCC
V
Low-level input voltage (driver, driver enable, and receiver enable inputs)
0
0.8
V
Differential input voltage
–12
12
V
IO
Output current, driver
–60
60
mA
IO
Output current, receiver
–8
8
mA
RL
Differential load resistance
54
CL
Differential load capacitance
VCC (1)
Supply voltage
VI
Input voltage at any bus terminal (separately or common mode) (2)
VIH
VIL
VID
1/tUI
TA
TJ
(1)
(2)
(3)
Signaling rate
(3)
UNIT
60
Ω
50
pF
SN65HVD72
250
kbps
SN65HVD75
20
Mbps
SN65HVD78
50
Mbps
Operating free-air temperature (See Thermal Information)
–40
125
°C
Junction temperature
–40
150
°C
Exposure to conditions beyond the recommended operation maximum for extended periods may affect device reliability.
The algebraic convention, in which the least positive (most negative) limit is designated as minimum, is used in this data sheet.
Operation is specified for internal (junction) temperatures up to 150°C. Self-heating due to internal power dissipation should be
considered for each application. Maximum junction temperature is internally limited by the thermal shutdown (TSD) circuit which disables
the driver outputs when the junction temperature reaches 170°C.
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
5
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
7.4 Thermal Information
SN65HVD72, SN65HVD75, SN65HVD78
THERMAL METRIC (1)
D (SOIC)
DGK (VSSOP)
DRB (VSON)
UNIT
8 PINS
RθJA
Junction-to-ambient thermal resistance
110.7
168.7
40
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
54.7
62.2
49.6
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
—
—
3.9
°C/W
RθJB
Junction-to-board thermal resistance
51.3
89.5
15.5
°C/W
ψJT
Junction-to-top characterization parameter
9.2
7.4
0.6
°C/W
ψJB
Junction-to-board characterization parameter
50.7
87.9
15.7
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
7.5 Electrical Characteristics
over recommended operating range (unless otherwise specified)
PARAMETER
TEST CONDITIONS
RL = 60 Ω, 375 Ω on each output to
–7 V to 12 V
|VOD|
Driver differential output
RL = 54 Ω (RS-485)
voltage magnitude
RL = 100 Ω (RS-422), TJ ≥ 0°C
VCC ≥ 3.2 V
Δ|VOD|
Change in magnitude of
driver differential output RL = 54 Ω, CL = 50 pF
voltage
VOC(SS)
Steady-state commonmode output voltage
Center of two 27-Ω load resistors
ΔVOC
Change in differential
driver output commonmode voltage
Center of two 27-Ω load resistors
VOC(PP)
Peak-to-peak driver
common-mode output
voltage
Center of two 27-Ω load resistors
COD
Differential output
capacitance
VIT+
Positive-going receiver
differential input voltage
threshold
VIT–
Negative-going receiver
differential input voltage
threshold
VHYS
Receiver differential
input voltage threshold
hysteresis (VIT+ – VIT–)
VOH
Receiver high-level
output voltage
IOH = –8 mA
VOL
Receiver low-level
output voltage
IOL = 8 mA
II
Driver input, driver
enable, and receiver
enable input current
IOZ
Receiver output highimpedance current
IOS
Driver short-circuit
output current
(1)
6
See
Figure 10
MIN
TYP
1.5
2
1.5
2
2
2.5
–50
0
50
mV
1
VCC/2
3
V
–50
0
50
mV
See
Figure 11
VO = 0 V or VCC, RE at VCC
UNIT
V
200
mV
15
pF
(1)
–70
–200
–150
50
80
2.4
VCC – 0.3
See
MAX
0.2
–20
mV
(1)
mV
See
mV
V
0.4
V
–2
2
µA
–1
1
µA
–160
160
mA
Under any specific conditions, VIT+ is assured to be at least VHYS higher than VIT–.
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
Electrical Characteristics (continued)
over recommended operating range (unless otherwise specified)
PARAMETER
TEST CONDITIONS
VCC = 3 to 3.6 V or
VCC = 0 V
DE at 0 V
Bus input current
(disabled driver)
II
Supply current
(quiescent)
ICC
Supply current
(dynamic)
SN65HVD72
SN65HVD75
SN65HVD78
MIN
TYP
MAX
75
150
–100
–40
VI = 12 V
VI = –7 V
VI = 12 V
VI = –7 V
240
–267
µA
333
–180
Driver and receiver
enabled
DE = VCC, RE = GND
No load
750
950
Driver enabled,
receiver disabled
DE = VCC, RE = VCC
No load
300
500
Driver disabled,
receiver enabled
DE = GND, RE = GND
No load
600
800
Driver and receiver
disabled
DE = GND, D = open
RE = VCC, No load
0.1
2
µA
See Typical Characteristics
Thermal shutdown
junction temperature
TTSD
UNIT
170
°C
7.6 Power Dissipation
PARAMETER
TEST CONDITIONS
Unterminated
PD
Power Dissipation
driver and receiver enabled,
VCC = 3.6 V, TJ = 150°C
50% duty cycle square-wave signal at
RS-422 load
signaling rate:
•
SN65HVD72 at 250 kbps
•
SN65HVD75 at 20 Mbps
•
SN65HVD78 at 50 Mbps
RS-485 load
RL = 300 Ω
CL = 50 pF
(driver)
RL = 100 Ω
CL = 50 pF
(driver)
RL = 54 Ω
CL = 50 pF
(driver)
VALUE
SN65HVD72
120
SN65HVD75
160
SN65HVD78
200
SN65HVD72
155
SN65HVD75
195
SN65HVD78
230
SN65HVD72
190
SN65HVD75
230
SN65HVD78
260
UNIT
mW
mW
mW
7.7 Switching Characteristics: 250 kbps Device (SN65HVD72) Bit Time ≥ 4 µs
over recommended operating conditions
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
0.3
0.7
1.2
µs
DRIVER
tr, tf
Driver differential output rise or
fall time
tPHL, tPLH
Driver propagation delay
tSK(P)
Driver pulse skew, |tPHL – tPLH|
tPHZ, tPLZ
Driver disable time
tPZH, tPZL
RL = 54 Ω
CL = 50 pF
Receiver enabled
Driver enable time
See Figure 12
0.7
See Figure 13
and Figure 14
Receiver disabled
1
µs
0.2
µs
0.1
0.4
µs
0.5
1
3
9
µs
RECEIVER
tr, tf
Receiver output rise or fall time
tPHL, tPLH
Receiver propagation delay time
tSK(P)
Receiver pulse skew, |tPHL – tPLH|
tPLZ, tPHZ
Receiver disable time
tPZL(1), tPZH(1),
Receiver enable time
tPZL(2), tPZH(2)
Copyright © 2012–2019, Texas Instruments Incorporated
CL = 15 pF
See Figure 15
12
30
ns
75
100
ns
3
15
ns
40
100
ns
Driver enabled
See Figure 16
20
50
ns
Driver disabled
See Figure 17
3
8
µs
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
7
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
7.8 Switching Characteristics: 20 Mbps Device (SN65HVD75) Bit Time ≥50 ns
over recommended operating conditions
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
2
7
14
ns
7
11
17
ns
DRIVER
Driver differential output rise or
fall time
tr, tf
tPHL, tPLH
Driver propagation delay
tSK(P)
Driver pulse skew, |tPHL – tPLH|
tPHZ, tPLZ
Driver disable time
tPZH, tPZL
RL = 54 Ω
CL = 50 pF
Receiver enabled
Driver enable time
See Figure 12
See Figure 13
and Figure 14
Receiver disabled
0
2
ns
12
50
ns
10
20
ns
3
7
µs
5
10
ns
60
70
ns
RECEIVER
tr, tf
Receiver output rise or fall time
tPHL, tPLH
Receiver propagation delay time
tSK(P)
Receiver pulse skew, |tPHL – tPLH|
tPLZ, tPHZ
Receiver disable time
tpZL(1), tPZH(1),
Receiver enable time
tPZL(2), tPZH(2)
CL = 15 pF
See Figure 15
0
6
ns
15
30
ns
Driver enabled
See Figure 16
10
50
ns
Driver disabled
See Figure 17
3
8
µs
7.9 Switching Characteristics: 50 Mbps Device (SN65HVD78) Bit Time ≥20 ns
over recommended operating conditions
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
1
3
6
ns
9
15
ns
DRIVER
Driver differential output rise or
fall time
tr, tf
tPHL, tPLH
Driver propagation delay
tSK(P)
Driver pulse skew, |tPHL – tPLH|
tPHZ, tPLZ
Driver disable time
tPZH, tPZL
RL = 54 Ω
CL = 50 pF
Receiver enabled
Driver enable time
See Figure 12
See Figure 13
and Figure 14
0
1
ns
10
30
ns
10
30
ns
8
µs
Receiver disabled
RECEIVER
tr, tf
Receiver output rise or fall time
tPHL, tPLH
Receiver propagation delay time
tSK(P)
Receiver pulse skew, |tPHL – tPLH|
tPLZ, tPHZ
Receiver disable time
tpZL(1), tPZH(1),
Receiver enable time
tPZL(2), tPZH(2)
8
Submit Documentation Feedback
1
CL = 15 pF
3
See Figure 15
6
ns
35
ns
2.5
ns
8
30
ns
Driver enabled
See Figure 16
10
30
ns
Driver disabled
See Figure 17
3
8
µs
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
7.10 Typical Characteristics
3.5
VCC = 3.3 V,
DE = VCC,
D=0V
VOH
3
2.5
2
1.5
VOL
1
0.5
0
0
20
40
60
80
IO - Driver Output Current - mA
100 W
VO - Driver Differential Output Voltage - V
VO - Driver Output Voltage - V
3.5
2.5
2
1.5
1
0.5
0
100
Figure 1. Driver Output Voltage vs Driver Output Current
0
20
40
60
80
IO - Driver Output Current - mA
100
Figure 2. Driver Differential Output Voltage vs Driver Output
Current
40
4
TA = 25°C
RL = 54 W
D = VCC
DE = VCC
30
3.5
3
Driver Rise and Fall Time - ns
35
IO - Driver Output Current - mA
VCC = 3.3 V,
DE = VCC,
D=0V
60 W
3
25
20
15
10
2.5
2
1.5
1
5
0.5
0
0
0.5
1
1.5
2
2.5
3
0
-40
3.5
-20
0
20
40
60
80
100
120
o
VCC Supply Voltage - V
Temperature - C
Figure 3. Driver Output Current vs Supply Voltage
Figure 4. SN65HVD78 Driver Rise or Fall Time vs
Temperature
70
12
RL = 54 W
60
50
ICC - Supply Current - mA
Driver Propagation Delay - ns
10
8
6
4
2
0
-40
40
30
20
10
-20
0
20
40
60
80
100
120
o
Temperature - C
Figure 5. SN65HVD78 Driver Propagation Delay vs
Temperature
Copyright © 2012–2019, Texas Instruments Incorporated
0
50
70
90
110
130
150
170
190
210
230
250
Signaling Rate - kbps
Figure 6. SN65HVD72 Supply Current vs Signal Rate
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
9
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
Typical Characteristics (continued)
70
70
RL = 54 W
60
60
50
50
ICC - Supply Current - mA
ICC - Supply Current - mA
RL = 54 W
40
30
20
10
40
30
20
10
0
0
0
2
4
6
8
10
12
14
16
18
0
20
5
10
Signaling Rate - Mbps
15
20
25
30
35
40
45
50
Signaling Rate - Mbps
Figure 7. SN65HVD75 Supply Current vs Signal Rate
Figure 8. SN65HVD78 Supply Current vs Signal Rate
3.5
Receiver Output (R) V
3
2.5
VIT- (-7V)
2
VIT-(0V)
VIT-(12V)
1.5
VIT+(-7V)
VIT+(0V)
1
VIT+(12V)
0.5
0
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
Differential Input Voltage (VID) mV
Figure 9. Receiver Output vs Input
10
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
8 Parameter Measurement Information
Input generator rate is 100 kbps, 50% duty cycle, rise or fall time is less than 6 ns, output impedance is 50 Ω.
375 : r 1%
V CC
DE
D
A
V OD
0 V or 3 V
60 : r 1%
+
_
B
± 7 V < V( test) < 12 V
375 : r 1%
Copyright © 2016, Texas Instruments Incorporated
Figure 10. Measurement of Driver Differential Output Voltage With Common-Mode Load
VA
B
VB
RL/2
A
0 V or 3 V
A
D
VOD
VOC(PP)
B
RL/2
CL
'VOC(SS)
VOC
VOC
Copyright © 2016, Texas Instruments Incorporated
Figure 11. Measurement of Driver Differential and Common-Mode Output With RS-485 Load
50%
50%
A
:
|
:
B
|
Copyright © 2016, Texas Instruments Incorporated
Figure 12. Measurement of Driver Differential Output Rise and Fall Times and Propagation Delays
3V
D
DE
Input
Generator
VI
50 :
A
3V
S1
B
CL = 50 pF r 20%
CL Includes Fixture
and Instrumentation
Capacitance
VO
VI
RL = 110:
r 1%
50%
50%
VO
0V
0. 5 V
tPZH
VOH
90%
50%
tPHZ
| 0V
Copyright © 2016, Texas Instruments Incorporated
D at 3 V to test non-inverting output, D at 0 V to test inverting output.
Figure 13. Measurement of Driver Enable and Disable Times With Active High Output and Pulldown Load
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
11
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
Parameter Measurement Information (continued)
3V
RL = 110:
A
3V
Input
Generator
S1
D
DE
r1%
VO
| 3V
VI
50%
50%
0V
B
t PZL
t PLZ
CL = 50 pFr 20%
VI
50 :
| 3V
CL Includes Fixture
and Instrumentation
Capacitance
VO
50%
10%
VOL
Copyright © 2016, Texas Instruments Incorporated
D at 0 V to test non-inverting output, D at 3 V to test inverting output.
Figure 14. Measurement of Driver Enable and Disable Times With Active Low Output and Pullup Load
3V
A
Input
Generator
R
VI
50 :
1. 5 V
0V
VI
VO
50%
50%
0V
B
tPLH
CL = 15 pF r 20%
t PHL
RE
VO
CL Includes Fixture
and Instrumentation
Capacitance
VOH
90% 90%
50%
10%
50%
10%
tr
VOL
tf
Copyright © 2016, Texas Instruments Incorporated
Figure 15. Measurement of Receiver Output Rise and Fall Times and Propagation Delays
12
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
Parameter Measurement Information (continued)
3V
V CC
DE
A
R VO
D
0 V or 3V
1k : r 1%
S1
B
RE
CL = 15 pFr 20%
CL
Input
Generator
Includes Fixture
and Instrumentation
Capacitance
50:
VI
3V
VI
50%
50%
0V
tPZH(1)
t PHZ
VOH
90%
VO
50%
D at 3V
S 1 to GND
| 0V
tPZL(1)
t PLZ
V CC
VO
50%
D at 0V
S 1 to VCC
10%
VOL
Copyright © 2016, Texas Instruments Incorporated
Figure 16. Measurement of Receiver Enable and Disable Times With Driver Enabled
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
13
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
Parameter Measurement Information (continued)
VCC
A
0 V or 1.5 V
R VO
S1
B
1.5 V or 0 V
RE
Input
Generator
VI
1 k: r 1%
CL = 15 pF r20%
CL Includes Fixture
and Instrumentation
Capacitance
50 :
3V
VI
50%
0V
tPZH(2)
VOH
VO
A at 1.5 V
B at 0 V
S1 to GND
50%
GND
tPZL(2)
VCC
VO
50%
A at 0 V
B at 1.5 V
S1 to VCC
VOL
Copyright © 2016, Texas Instruments Incorporated
Figure 17. Measurement of Receiver Enable Times With Driver Disabled
14
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
9 Detailed Description
9.1 Overview
The SN65HVD72, SN65HVD75, and SN65HVD78 are low-power, half-duplex RS-485 transceivers available in 3
speed grades suitable for data transmission up to 250 kbps, 20 Mbps, and 50 Mbps.
These devices have active-high driver enables and active-low receiver enables. A standby current of less than
2 µA can be achieved by disabling both driver and receiver.
9.2 Functional Block Diagram
9.3 Feature Description
Internal ESD protection circuits protect the transceiver against electrostatic discharges (ESD) according to IEC
61000-4-2 of up to ±12 kV, and against electrical fast transients (EFT) according to IEC 61000-4-4 of up to
±4 kV.
The SN65HVD7x half-duplex family provides internal biasing of the receiver input thresholds in combination with
large input threshold hysteresis. At a positive input threshold of VIT+ = –20 mV and an input hysteresis of
VHYS = 50 mV, the receiver output remains logic high under a bus-idle or bus-short condition even in the
presence of 140-mVPP differential noise without the need for external failsafe biasing resistors.
Device operation is specified over a wide ambient temperature range from –40°C to 125°C.
9.4 Device Functional Modes
When the driver enable pin, DE, is logic high, the differential outputs A and B follow the logic states at data input
D. A logic high at D causes A to turn high and B to turn low. In this case the differential output voltage defined as
VOD = VA – VB is positive. When D is low, the output states reverse, B turns high, A becomes low, and VOD is
negative.
When DE is low, both outputs turn high-impedance. In this condition the logic state at D is irrelevant. The DE pin
has an internal pulldown resistor to ground; thus, when left open, the driver is disabled (high-impedance) by
default. The D pin has an internal pullup resistor to VCC; thus, when left open while the driver is enabled, output A
turns high and B turns low.
Table 1. Driver Function Table
INPUT
ENABLE
D
DE
A
H
H
H
L
Actively drive bus high
L
H
L
H
Actively drive bus low
X
L
Z
Z
Driver disabled
X
OPEN
Z
Z
Driver disabled by default
OPEN
H
H
L
Actively drive bus high by default
Copyright © 2012–2019, Texas Instruments Incorporated
OUTPUTS
B
DESCRIPTION
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
15
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
When the receiver enable pin, RE, is logic low, the receiver is enabled. When the differential input voltage
defined as VID = VA – VB is positive and higher than the positive input threshold, VIT+, the receiver output, R,
turns high. When VID is negative and lower than the negative input threshold, VIT–, the receiver output turns low.
If VID is between VIT+ and VIT–, the output is indeterminate.
When RE is logic high or left open, the receiver output is high-impedance and the magnitude and polarity of VID
are irrelevant. Internal biasing of the receiver inputs causes the output to go failsafe-high when the transceiver is
disconnected from the bus (open-circuit), the bus lines are shorted (short-circuit), or the bus is not actively driven
(idle bus).
Table 2. Receiver Function Table
DIFFERENTIAL INPUT
ENABLE
OUTPUT
VID = VA – VB
RE
R
VIT+ < VID
L
H
Receive valid bus high
VIT– < VID < VIT+
L
?
Indeterminate bus state
VID < VIT–
L
L
Receive valid bus low
X
H
Z
Receiver disabled
X
OPEN
Z
Receiver disabled by default
Open-circuit bus
L
H
Failsafe high output
Short-circuit bus
L
H
Failsafe high output
Idle (terminated) bus
L
H
Failsafe high output
D and RE Inputs
D , RE
DESCRIPTION
DE Input
Vcc
3M
1. 5 k
Vcc
R Output
Vcc
1. 5 k
DE
R
9V
9V
9V
1M
Receiver Inputs
Vcc
Driver Outputs
Vcc
R2
R2
R1
A
B
A
R
R1
B
16 V
R3
R3
16 V
Copyright © 2016, Texas Instruments Incorporated
Figure 18. Equivalent Input and Output Circuit Diagrams
16
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
The SN65HVD72, SN65HVD75, and SN65HVD78 are half-duplex RS-485 transceivers commonly used for
asynchronous data transmission. The driver and receiver enable pins allow for the configuration of different
operating modes.
R
R
R
R
R
R
RE
A
RE
A
RE
A
DE
B
DE
B
DE
B
D
D
D
a) Independent driver and
receiver enable signals
D
D
b) Combined enable signals for
use as directional control pin
D
c) Receiver always on
Copyright © 2016, Texas Instruments Incorporated
Figure 19. Transceiver Configurations
Using independent enable lines provides the most flexible control as it allows for the driver and the receiver to be
turned on and off individually. While this configuration requires two control lines, it allows for selective listening
into the bus traffic, whether the driver is transmitting data or not.
Combining the enable signals simplifies the interface to the controller by forming a single direction-control signal.
In this configuration, the transceiver operates as a driver when the direction-control line is high, and as a receiver
when the direction-control line is low.
Additionally, only one line is required when connecting the receiver-enable input to ground and controlling only
the driver-enable input. In this configuration, a node not only receives the data from the bus, but also the data it
sends and can verify that the correct data have been transmitted.
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
17
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
10.2 Typical Application
An RS-485 bus consists of multiple transceivers connected in parallel to a bus cable. To eliminate line
reflections, each cable end is terminated with a termination resistor, RT, whose value matches the characteristic
impedance, Z0, of the cable. This method, known as parallel termination, allows for relatively high data rates over
long cable lengths.
R
R
RE
B
DE
D
R
A
R
A
RT
RT
D
A
B
R
A
R
D
R RE DE D
RE
B
DE
D
B
D
D
R RE DE D
Copyright © 2016, Texas Instruments Incorporated
Figure 20. Typical RS-485 Network With SN65HVD7x Transceivers
Common cables used are unshielded twisted pair (UTP), such as low-cost CAT-5 cable with Z0 = 100 Ω, and
RS-485 cable with Z0 = 120 Ω. Typical cable sizes are AWG 22 and AWG 24.
The maximum bus length is typically given as 4000 ft or 1200 m, and represents the length of an AWG 24 cable
whose cable resistance approaches the value of the termination resistance, thus reducing the bus signal by half
or 6 dB. Actual maximum usable cable length depends on the signaling rate, cable characteristics, and
environmental conditions.
10.2.1 Design Requirements
RS-485 is a robust electrical standard suitable for long-distance networking that may be used in a wide range of
applications with varying requirements, such as distance, data rate, and number of nodes.
10.2.1.1 Data Rate and Bus Length
There is an inverse relationship between data rate and bus length, meaning the higher the data rate, the shorter
the cable length; and conversely, the lower the data rate, the longer the cable may be without introducing data
errors. While most RS-485 systems use data rates between 10 kbps and 100 kbps, some applications require
data rates up to 250 kbps at distances of 4000 feet and longer. Longer distances are possible by allowing for
small signal jitter of up to 5 or 10%.
10000
Cable Length (ft)
5%, 10%, and 20% Jitter
1000
Conservative
Characteristics
100
10
100
1k
10 k
100 k
1M
10 M
100 M
Data Rate (bps)
Figure 21. Cable Length vs Data Rate Characteristic
18
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
Typical Application (continued)
10.2.1.2 Stub Length
When connecting a node to the bus, the distance between the transceiver inputs and the cable trunk, known as
the stub, should be as short as possible. Stubs present a non-terminated piece of bus line which can introduce
reflections as the length of the stub increases. As a general guideline, the electrical length, or round-trip delay, of
a stub should be less than one-tenth of the rise time of the driver, thus giving a maximum physical stub length as
shown in Equation 1.
Lstub ≤ 0.1 × tr × v × c
where:
•
•
•
tr is the 10/90 rise time of the driver
c is the speed of light (3 × 108 m/s)
v is the signal velocity of the cable or trace as a factor of c
(1)
Per Equation 1, Table 3 shows the maximum cable-stub lengths for the minimum driver output rise times of the
SN65HVD7x half-duplex family of transceivers for a signal velocity of 78%.
Table 3. Maximum Stub Length
MAXIMUM STUB LENGTH
DEVICE
MINIMUM DRIVER OUTPUT RISE TIME
(ns)
SN65HVD72
300
7
23
SN65HVD75
2
0.05
0.16
SN65HVD78
1
0.025
0.08
(m)
(ft)
10.2.1.3 Bus Loading
The RS-485 standard specifies that a compliant driver must be able to drive 32 unit loads (UL), where 1 unit load
represents a receiver input current of 1 mA at 12 V, or a load impedance of approximately 12 kΩ. Because the
SN65HVD72 and SN65HVD75 have a receiver input current of 150 µA at 12 V, they are 3/20 UL transceivers,
and no more than 213 transceivers should be connected to the bus. Similarly, the SN65HVD78 has a receiver
input current of 333 µA at 12 V and is a 1/3 UL transceiver, meaning no more than 96 transceivers should be
connected to the bus.
10.2.1.4
Receiver Failsafe
The differential receiver is failsafe to invalid bus states caused by:
• Open bus conditions such as a disconnected connector
• Shorted bus conditions such as cable damage shorting the twisted-pair together, or
• Idle bus conditions that occur when no driver on the bus is actively driving
In any of these cases, the differential receiver will output a failsafe logic high so that the output of the receiver is
not indeterminate.
Receiver failsafe is accomplished by offsetting the receiver thresholds such that the input-indeterminate range
does not include zero volts differential. To comply with the RS-422 and RS-485 standards, the receiver output
must output a high when the differential input VID is more positive than 200 mV, and must output a low when VID
is more negative than –200 mV. The receiver parameters which determine the failsafe performance are VIT+,
VIT–, and VHYS (the separation between VIT+ and VIT–). As shown in Electrical Characteristics, differential signals
more negative than –200 mV will always cause a low receiver output, and differential signals more positive than
200 mV will always cause a high receiver output.
When the differential input signal is close to zero, it is still above the maximum VIT+ threshold of –20 mV, and the
receiver output will be high. Only when the differential input is more than VHYS below VIT+ will the receiver output
transition to a low state. Therefore, the noise immunity of the receiver inputs during a bus fault condition includes
the receiver hysteresis value, VHYS, as well as the value of VIT+.
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
19
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
R
VHYS-min
50mV
-70
-20
70
0
VID - mV
Vnoise-max = 140mVpp
Figure 22. SN65HVD7x Noise Immunity
10.2.1.5 Transient Protection
The bus pins of the SN65HVD7x transceiver family possess on-chip ESD protection against ±15-kV human body
model (HBM) and ±12-kV IEC 61000-4-2 contact discharge. The IEC-ESD test is far more severe than the HBMESD test. The 50% higher charge capacitance, CS, and 78% lower discharge resistance, RD, of the IEC-model
produce significantly higher discharge currents than the HBM-model.
As stated in the IEC 61000-4-2 standard, contact discharge is the preferred test method; although IEC air-gap
testing is less repeatable than contact testing, air discharge protection levels are inferred from the contact
discharge test results.
RD
50M
(1M)
High-Voltage
Pulse
Generator
330
(1.5k)
CS
150pF
(100pF)
Device
Under
Test
Current - A
RC
40
35
30
25
20
15
10
5
0
10kV IEC
10kV HBM
0
50
100
150
200
250
300
Time - ns
Copyright © 2016, Texas Instruments Incorporated
Figure 23. HBM and IEC-ESD Models and Currents in Comparison (HBM Values in Parenthesis)
The on-chip implementation of IEC ESD protection significantly increases the robustness of equipment. Common
discharge events occur due to human contact with connectors and cables. Designers may choose to implement
protection against longer duration transients, typically referred to as surge transients.
EFTs are generally caused by relay-contact bounce or the interruption of inductive loads. Surge transients often
result from lightning strikes (direct strike or an indirect strike which induce voltages and currents), or the
switching of power systems, including load changes and short circuit switching. These transients are often
encountered in industrial environments, such as factory automation and power-grid systems.
Figure 24 compares the pulse-power of the EFT and surge transients with the power caused by an IEC ESD
transient. The left-hand diagram shows the relative pulse-power for a 0.5-kV surge transient and 4-kV EFT
transient, both of which dwarf the 10-kV ESD transient visible in the lower-left corner. 500-V surge transients are
representative of events that may occur in factory environments in industrial and process automation.
The right-hand diagram shows the pulse-power of a 6-kV surge transient, relative to the same 0.5-kV surge
transient. 6-kV surge transients are most likely to occur in power generation and power-grid systems.
20
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
22
20
18
16
14
12
10
8
6
4
2
0
Pulse Power (MW)
Pulse Power (kW)
www.ti.com
0.5-kV Surge
4-kV EFT
10-kV ESD
0
5
10
15
20
25
30
35
3.0
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
6-kV Surge
0.5-kV Surge
0
40
5
10
15
20
25
30
35
40
Time (µs)
Time (µs)
Figure 24. Power Comparison of ESD, EFT, and Surge Transients
In the case of surge transients, high-energy content is characterized by long pulse duration and slow decaying
pulse power. The electrical energy of a transient that is dumped into the internal protection cells of a transceiver
is converted into thermal energy which heats and destroys the protection cells, thus destroying the transceiver.
Figure 25 shows the large differences in transient energies for single ESD, EFT, and surge transients, as well as
for an EFT pulse train, commonly applied during compliance testing.
1000
100
Surge
10
1
Pulse Energy (J)
EFT Pulse Train
0.1
0.01
EFT
10-3
10-4
ESD
10-5
10-6
0.5
1
2
4
6
8 10
15
Peak Pulse Voltage (kV)
Figure 25. Comparison of Transient Energies
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
21
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
10.2.2 Detailed Design Procedure
10.2.2.1 External Transient Protection
To protect bus nodes against high-energy transients, the implementation of external transient protection devices
is necessary. Figure 26 suggests two circuits that provide protection against light and heavy surge transients, in
addition to ESD and EFT transients. Table 4 presents the associated bill of materials.
Table 4. Bill of Materials
DEVICE
FUNCTION
ORDER NUMBER
MANUFACTURER
XCVR
3.3-V, 250-kbps RS-485 Transceiver
SN65HVD72D
R1, R2
10-Ω, Pulse-Proof Thick-Film Resistor
CRCW060310RJNEAHP
Vishay
TVS
Bidirectional 400-W Transient Suppressor
CDSOT23-SM712
Bourns
TBU1, TBU2
Bidirectional Surge Suppressor
TBU-CA-065-200-WH
Bourns
MOV1, MOV2
200-mA Transient Blocking Unit, 200-V, MetalOxide Varistor
MOV-10D201K
Bourns
Vcc
Vcc
Vcc
10k
1
R
2
RE
DIR
3
DE
TxD
4
D
RxD
MCU
TI
Vcc
8
B
7
A
6
GND
5
XCVR
0.1 F
Vcc
10k
R1
1
R
2
RE
DIR
3
DE
TxD
4
D
RxD
TVS
MCU
Vcc
8
B
7
A
6
GND
5
XCVR
0.1 F
R2
10k
R1
TBU1
MOV1
TVS
MOV2
R2
10k
TBU2
Copyright © 2016, Texas Instruments Incorporated
Figure 26. Transient Protections Against ESD, EFT, and Surge Transients
The left-hand circuit provides surge protection of ≥500-V surge transients, while the right-hand circuit can
withstand surge transients of up to 5 kV.
22
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
10.2.2.2 Isolated Bus Node Design
Many RS-485 networks use isolated bus nodes to prevent the creation of unintended ground loops and their
disruptive impact on signal integrity. An isolated bus node typically includes a microcontroller that connects to the
bus transceiver via a multi-channel, digital isolator (Figure 27).
0.1 F
2
Vcc D2 3
1:1.33 MBR0520L
SN6501
GND D1
N
3
1
10 F
IN
OUT
1
3.3VISO
TLV70733
10 F 0.1 F
4,5
L1
4
EN
GND
2
10 F
MBR0520L
ISO-BARRIER
3.3V
0.1 F
PSU
0.1 F
PE
0.1 F
4.7k
PE
2
DVcc
5
6
XOUT
XIN
UCA0RXD
P3.0
MSP430
F2132
DVss
P3.1
UCA0TXD
4
16
11
12
15
1
16
Vcc1
Vcc2
7
10
EN1 ISO7241 EN2
11
6
OUTD
IND
3
14
INA
OUTA
4
13
OUTB
INB
5
12
INC
OUTC
GND1
GND2
2,8
0.1 F
4.7k
1
R
8
Vcc
7
B
RE SN65
3
DE HVD72 6
A
4
D GND2
2
5
R1
R2
TVS
9,15
R HV
Short thick Earth wire or Chassis
Protective Earth Ground,
Equipment Safety Ground
Floating RS-485 Common
C HV
PE
island
R1,R2, TVS: see Table 1
RHV = 1M , 2kV high-voltage resistor, TT electronics, HVC 2010 1M0 G T3
CHV = 4.7nF, 2kV high-voltage capacitor, NOVACAP, 1812 B 472 K 202 N T
Copyright © 2016, Texas Instruments Incorporated
Figure 27. Isolated Bus Node with Transient Protection
Power isolation is accomplished using the push-pull transformer driver SN6501 and a low-cost LDO, TLV70733.
Signal isolation uses the quadruple digital isolator ISO7241. Notice that both enable inputs, EN1 and EN2, are
pulled up via 4.7 kΩ resistors to limit their input currents during transient events.
While the transient protection is similar to the one in Figure 26 (left circuit), an additional high-voltage capacitor is
used to divert transient energy from the floating RS-485 common further towards Protective Earth (PE) ground.
This is necessary as noise transients on the bus are usually referred to Earth potential.
RHV refers to a high voltage resistor, and in some applications even a varistor. This resistance is applied to
prevent charging of the floating ground to dangerous potentials during normal operation.
Occasionally varistors are used instead of resistors to rapidly discharge CHV, if it is expected that fast transients
might charge CHV to high-potentials.
Note that the PE island represents a copper island on the PCB for the provision of a short, thick Earth wire
connecting this island to PE ground at the entrance of the power supply unit (PSU).
In equipment designs using a chassis, the PE connection is usually provided through the chassis itself. Typically
the PE conductor is tied to the chassis at one end while the high-voltage components, CHV and RHV, are
connecting to the chassis at the other end.
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
23
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
10.2.3 Application Curves
RL = 60 Ω
RL = 60 Ω
Figure 28. SN65HVD72, 250 kbps
Figure 29. SN65HVD75, 20 Mbps
RL = 60 Ω
Figure 30. SN65HVD78, 50 Mbps
11 Power Supply Recommendations
To assure reliable operation at all data rates and supply voltages, each supply should be buffered with a 100-nF
ceramic capacitor located as close to the supply pins as possible. The TPS76333 is a linear voltage regulator
suitable for the 3.3 V supply.
See the SN6501 data sheet for isolated power supply designs.
24
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
12 Layout
12.1 Layout Guidelines
On-chip IEC ESD protection is sufficient for laboratory and portable equipment but often insufficient for EFT and
surge transients occurring in industrial environments. Therefore, robust and reliable bus node design requires the
use of external transient protection devices.
Because ESD and EFT transients have a wide frequency bandwidth from approximately 3 MHz to 3 GHz, highfrequency layout techniques must be applied during PCB design.
For a successful PCB design, start with the design of the protection circuit in mind.
1. Place the protection circuitry close to the bus connector to prevent noise transients from entering the board.
2. Use VCC and ground planes to provide low-inductance. Note that high-frequency currents follow the path of
least inductance and not the path of least impedance.
3. Design the protection components into the direction of the signal path. Do not force the transients currents to
divert from the signal path to reach the protection device.
4. Apply 100-nF to 220-nF bypass capacitors as close as possible to the VCC pins of transceiver, UART, and
controller ICs on the board.
5. Use at least two vias for VCC and ground connections of bypass capacitors and protection devices to
minimize effective via-inductance.
6. Use 1-kΩ to 10-kΩ pullup or pulldown resistors for enable lines to limit noise currents in these lines during
transient events.
7. Insert pulse-proof series resistors into the A and B bus lines if the TVS clamping voltage is higher than the
specified maximum voltage of the transceiver bus pins. These resistors limit the residual clamping current
into the transceiver and prevent it from latching up.
8. While pure TVS protection is sufficient for surge transients up to 1 kV, higher transients require metal-oxide
varistors (MOVs) which reduce the transients to a few hundred volts of clamping voltage, and transient
blocking units (TBUs) that limit transient current to 200 mA.
12.2 Layout Example
5
Via to ground
Via to VCC
4
6 R
1
R
MCU
R
7
5
R
6 R
SN65HVD7x
JMP
C
R
TVS
5
Figure 31. SN65HVD7x Half-Duplex Layout Example
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
25
SN65HVD72, SN65HVD75, SN65HVD78
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
www.ti.com
13 Device and Documentation Support
13.1 Device Support
13.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
13.2 Documentation Support
13.2.1 Related Documentation
For related documentation see the following:
SN6501 Transformer Driver for Isolated Power Supplies, SLLSEA0
13.3 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 5. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
SN65HVD72
Click here
Click here
Click here
Click here
Click here
SN65HVD75
Click here
Click here
Click here
Click here
Click here
SN65HVD78
Click here
Click here
Click here
Click here
Click here
13.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
13.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
13.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
13.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
26
Submit Documentation Feedback
Copyright © 2012–2019, Texas Instruments Incorporated
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
SN65HVD72, SN65HVD75, SN65HVD78
www.ti.com
SLLSE11H – MARCH 2012 – REVISED MARCH 2019
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2012–2019, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN65HVD72 SN65HVD75 SN65HVD78
27
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
SN65HVD72D
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HVD72
SN65HVD72DGK
ACTIVE
VSSOP
DGK
8
80
RoHS & Green
NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
HVD72
SN65HVD72DGKR
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green
NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
HVD72
SN65HVD72DR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HVD72
SN65HVD72DRBR
ACTIVE
SON
DRB
8
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
HVD72
SN65HVD72DRBT
ACTIVE
SON
DRB
8
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
HVD72
SN65HVD75D
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HVD75
SN65HVD75DGK
ACTIVE
VSSOP
DGK
8
80
RoHS & Green
NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
HVD75
SN65HVD75DGKR
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green
NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
HVD75
SN65HVD75DR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HVD75
SN65HVD75DRBR
ACTIVE
SON
DRB
8
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
HVD75
SN65HVD75DRBT
ACTIVE
SON
DRB
8
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
HVD75
SN65HVD78D
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HVD78
SN65HVD78DGK
ACTIVE
VSSOP
DGK
8
80
RoHS & Green
NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
HVD78
SN65HVD78DGKR
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green
NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
HVD78
SN65HVD78DR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HVD78
SN65HVD78DRBR
ACTIVE
SON
DRB
8
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
HVD78
SN65HVD78DRBT
ACTIVE
SON
DRB
8
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
HVD78
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of