SN74ABT2241NSRG4

SN54ABT2241, SN74ABT2241 OCTAL BUFFERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS233B – JANUARY 1991 – REVISED JANUARY 1997 D D D D Output Ports Have Equivalent 25-Ω Series Resistors, So No External Resistors Are Required State-of-the-Art EPIC-ΙΙB  BiCMOS Design Significantly Reduces Power Dissipation Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages, Ceramic Chip Carriers (FK), and Plastic (N) and Ceramic (J) DIPs SN54ABT2241 . . . J PACKAGE SN74ABT2241 . . . DB, DW, N, OR PW PACKAGE (TOP VIEW) 1OE 1A1 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 2OE 1Y1 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 description 1A2 2Y3 1A3 2Y2 1A4 2OE 2Y4 1A1 1OE VCC SN54ABT2241 . . . FK PACKAGE (TOP VIEW) 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 1Y1 2A4 1Y2 2A3 1Y3 2Y1 GND 2A1 1Y4 2A2 These octal buffers and line drivers are designed specifically to improve both the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. Together with the SN54ABT2240, SN74ABT2240A and ’ABT2244A, these devices provide the choice of selected combinations of inverting and noninverting outputs, symmetrical active-low output-enable (OE) inputs, and complementary OE and OE inputs. These devices feature high fan-out and improved fan-in. The outputs, which are designed to sink up to 12 mA, include equivalent 25-Ω series resistors to reduce overshoot and undershoot. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by the current-sourcing capability of the driver. The SN54ABT2241 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74ABT2241 is characterized for operation from –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC-ΙΙB is a trademark of Texas Instruments Incorporated. Copyright  1997, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ABT2241, SN74ABT2241 OCTAL BUFFERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS233B – JANUARY 1991 – REVISED JANUARY 1997 FUNCTION TABLES INPUTS 1OE 1A OUTPUT 1Y L H H L L L H X Z INPUTS 2OE 2A OUTPUT 2Y H H H H L L L X Z logic symbol† 1OE 1A1 1A2 1A3 1A4 1 2OE EN 2 1 18 4 16 6 14 8 12 1Y1 2A1 1Y2 2A2 1Y3 2A3 1Y4 2A4 19 11 EN 9 1 13 7 15 5 17 3 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. logic diagram (positive logic) 1OE 1A1 1A2 1A3 1A4 2 1 2OE 2 18 4 16 6 14 8 12 1Y1 2A1 1Y2 2A2 1Y3 2A3 1Y4 2A4 POST OFFICE BOX 655303 19 11 9 13 7 15 5 17 3 • DALLAS, TEXAS 75265 2Y1 2Y2 2Y3 2Y4 2Y1 2Y2 2Y3 2Y4 SN54ABT2241, SN74ABT2241 OCTAL BUFFERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS233B – JANUARY 1991 – REVISED JANUARY 1997 schematic of Y outputs VCC Output GND absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V Current into any output in the low state, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51, except for through-hole packages, which use a trace length of zero. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ABT2241, SN74ABT2241 OCTAL BUFFERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS233B – JANUARY 1991 – REVISED JANUARY 1997 recommended operating conditions (see Note 3) SN54ABT2241 VCC VIH Supply voltage VIL VI Low-level input voltage IOH IOL High-level output current ∆t/∆v Input transition rise or fall rate High-level input voltage SN74ABT2241 MIN MAX MIN MAX 4.5 5.5 4.5 5.5 2 2 0.8 Input voltage 0 Low-level output current Outputs enabled TA Operating free-air temperature NOTE 3: Unused inputs must be held high or low to prevent them from floating. –55 0 V V 0.8 VCC –24 UNIT VCC –32 V V mA 12 12 mA 5 5 ns/V 85 °C 125 –40 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V, II = –18 mA IOH = –3 mA VCC = 5 V, VCC = 4 4.5 5V SN54ABT2241 MIN –1.2 MAX SN74ABT2241 MIN –1.2 2.5 2.5 IOH = –3 mA IOH = –24 mA 3 3 3 2 2 2* VCC = 4.5 V, IOH = –32 mA IOL = 12 mA II IOZH VCC = 5.5 V, VCC = 5.5 V, VI = VCC or GND VO = 2.7 V IOZL Ioff VCC = 5.5 V, VCC = 0, VO = 0.5 V VI or VO ≤ 4.5 V ICEX VCC = 5.5 V, VO = 5.5 V Outputs high IO‡ VCC = 5.5 V, VCC = 5.5 V, IO = 0, VI = VCC or GND Data inputs ∆ICC§ Control inputs Ci VCC = 5.5 V, One input at 3.4 V,, Other inputs at VCC or GND VO = 2.5 V Outputs high V 2 0.8 0.8 0.8 ±1 ±1 ±1 V µA mV 50 50 50 µA –50 –50 –50 µA ±100 µA 50 µA –180 mA 250 µA ±100 50 –50 UNIT V 100 ICC –100 –180 1 250 50 –50 –180 –50 250 Outputs low 24 30 30 30 mA Outputs disabled 0.5 250 250 250 µA Outputs enabled 1.5 1.5 1.5 Outputs disabled 0.05 0.05 0.05 1.5 1.5 1.5 VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V 3 Co Co 8.5 * On products compliant to MIL-PRF-38535, this parameter does not apply. † All typical values are at VCC = 5 V. ‡ Not more than one output should be tested at a time, and the duration of the test should not exceed one second. § This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 MAX –1.2 2.5 VOL Vhys Ci TA = 25°C TYP† MAX MIN POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 mA pF pF SN54ABT2241, SN74ABT2241 OCTAL BUFFERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS233B – JANUARY 1991 – REVISED JANUARY 1997 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tPLH tPHL A Y tPZH tPZL OE or OE Y tPHZ tPLZ OE or OE Y PARAMETER VCC = 5 V, TA = 25°C SN54ABT2241 SN74ABT2241 MIN TYP MAX MIN MAX MIN MAX 1 3 4.3 1 4.8 1 4.7 1 4.3 5.3 1 5.7 1 5.6 1.1 3.5 4.8 1.1 6.1 1.1 5.8 2.1 6.2 7.6 2.1 8.6 2.1 8.4 1.7 4.2 5.6 1.7 6.7 1.7 6.6 1.7 3.9 5.8 1.7 6.9 1.7 6.4 UNIT ns ns ns PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54ABT2241, SN74ABT2241 OCTAL BUFFERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS233B – JANUARY 1991 – REVISED JANUARY 1997 PARAMETER MEASUREMENT INFORMATION 7V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open LOAD CIRCUIT 3V Timing Input 1.5 V 0V tw tsu 3V Input 1.5 V 1.5 V th 3V Data Input 1.5 V 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.5 V Input 1.5 V 0V VOH 1.5 V Output 1.5 V VOL VOH Output 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V tPLZ Output Waveform 1 S1 at 7 V (see Note B) tPLH tPHL 1.5 V tPZL tPHL tPLH 3V Output Control Output Waveform 2 S1 at Open (see Note B) 1.5 V tPZH 3.5 V VOL + 0.3 V VOL tPHZ 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74ABT2241DBR ACTIVE SSOP DB 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AA241 SN74ABT2241DW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ABT2241 SN74ABT2241DWR ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ABT2241 SN74ABT2241PWR ACTIVE TSSOP PW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AA241 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of