SN74ABT2245N

SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS234D – SEPTEMBER 1992 – REVISED MAY 1997 D D D D D DIR A1 A2 A3 A4 A5 A6 A7 A8 GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC OE B1 B2 B3 B4 B5 B6 B7 B8 SN54ABT2245 . . . FK PACKAGE (TOP VIEW) A3 A4 A5 A6 A7 description 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 B1 B2 B3 B4 B5 A8 GND B8 B7 B6 These octal transceivers and line drivers are designed for asynchronous communication between data buses. The devices transmit data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so the buses are effectively isolated. OE D SN54ABT2245 . . . J OR W PACKAGE SN74ABT2245 . . . DB, DW, N, OR PW PACKAGE (TOP VIEW) B-Port Outputs Have Equivalent 25-Ω Series Resistors, So No External Resistors Are Required State-of-the-Art EPIC-ΙΙB  BiCMOS Design Significantly Reduces Power Dissipation Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17 ESD Protection Exceeds 2000 V Per MIL-STD-833, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C High-Impedance State During Power Up and Power Down Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages, Ceramic Chip Carriers (FK), Plastic (N) and Ceramic (J) DIPs, and Ceramic Flat (W) Package A2 A1 DIR VCC D The B-port outputs, which are designed to sink up to 12 mA, include equivalent 25-Ω series resistors to reduce overshoot and undershoot. When VCC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 2.1 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking/current-sourcing capability of the driver. The SN54ABT2245 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74ABT2245 is characterized for operation from –40°C to 85°C. FUNCTION TABLE INPUTS OE DIR OPERATION L L B data to A bus L H A data to B bus H X Isolation Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC-ΙΙB is a trademark of Texas Instruments Incorporated. Copyright  1997, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS234D – SEPTEMBER 1992 – REVISED MAY 1997 logic symbol† 19 OE 1 DIR 2 A1 G3 3 EN1 [BA] 3 EN2 [AB] 18 1 B1 2 A2 A3 A4 A5 A6 A7 A8 3 17 4 16 5 15 6 14 7 13 8 12 9 11 B2 B3 B4 B5 B6 B7 B8 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. logic diagram (positive logic) DIR 1 19 A1 2 18 To Seven Other Channels 2 OE POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 B1 SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS234D – SEPTEMBER 1992 – REVISED MAY 1997 schematic of A-port outputs schematic of B-port outputs VCC VCC 25 Ω Output Output GND GND All resistor values shown are nominal. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (except I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT2245 (except B port) . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT2245 (except B port) . . . . . . . . . . . . . . . . . . . . . 128 mA B port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51, except for through-hole packages, which use a trace length of zero. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS234D – SEPTEMBER 1992 – REVISED MAY 1997 recommended operating conditions (see Note 3) SN54ABT2245 VCC VIH Supply voltage VIL VI Low-level input voltage High-level input voltage MAX MIN MAX 4.5 5.5 4.5 5.5 2 2 0.8 Input voltage 0 V V –12 –12 A port 48 64 B port 12 12 IOL Low level output current Low-level ∆t/∆v Input transition rise or fall rate ∆t/∆VCC TA Power-up ramp rate 200 Operating free-air temperature –55 Outputs enabled POST OFFICE BOX 655303 0.8 B port High level output current High-level • DALLAS, TEXAS 75265 5 5 –40 mA mA ns/V µs/V 200 125 V VCC –32 A port IOH 0 UNIT V VCC –24 NOTE 3: Unused pins (input or I/O) must be held high or low to prevent them from floating. 4 SN74ABT2245 MIN 85 °C SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS234D – SEPTEMBER 1992 – REVISED MAY 1997 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK B port TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V, II = –18 mA IOH = –1 mA VCC = 5 V, VCC = 4 4.5 5V VOH A port VCC = 4.5 V, VCC = 5 V, 5V VCC = 4 4.5 B port VOL VCC = 4 4.5 5V A port MIN SN54ABT2245 MIN –1.2 MAX SN74ABT2245 MIN –1.2 MAX –1.2 3.35 3.3 3.35 IOH = –1 mA IOH = –3 mA 3.85 3.8 3.85 3 3.1 IOH = –12 mA IOH = –3 mA 2.6 2.5 2.5 2.5 IOH = –3 mA IOH = –24 mA 3 3 3 2 2 IOH = –32 mA IOL = 8 mA 2* 2.6 A or B ports V V 0.65 0.8 0.65 0.8 0.8 0.55 IOL = 64 mA 0.55 0.55* VCC = 0 to 5.5 V, VI = VCC or GND VCC = 2.1 V to 5.5 V, VI = VCC or GND V 0.55 100 Control inputs UNIT 2 IOL = 12 mA IOL = 48 mA Vhys II TA = 25°C TYP† MAX mV ±1 ±1 ±1 ±20 ±20 ±20 µA IOZH‡ VCC = 2.1 V to 5.5 V, VO = 2.7 V, OE ≥ 2 V 10 10 10 µA IOZL‡ VCC = 2.1 V to 5.5 V, VO = 0.5 V, OE ≥ 2 V –10 –10 –10 µA IOZPU§ VCC = 0 to 2.1 V, VO = 0.5 V to 2.7 V, OE = X ±50 ±50 ±50 µA IOZPD§ VCC = 2.1 V to 0, VO = 0.5 V to 2.7 V, OE = X ±50 ±50 ±50 µA Ioff ICEX VCC = 0, VCC = 5.5 V, ±100 µA 50 µA IO¶ ICC Outputs high B port 50 –25 50 –100 –25 –100 –25 –100 –100 –180 –50 –180 –50 –180 VO = 2.5 25V VCC = 5.5 V, IO = 0, VI = VCC or GND Outputs high 1 250 250 250 µA A or B ports Outputs low 24 32 32 32 mA Outputs disabled 0.5 250 250 250 µA Outputs enabled 1.5 1.5 1.5 Data inputs VCC = 5.5 V, One input at 3.4 V,, Other inputs at VCC or GND Outputs disabled 0.05 0.05 0.05 1.5 1.5 1.5 Control inputs Cio ±100 VCC = 5 5.5 5 V, V A port ∆ICC# Ci VI or VO ≤ 4.5 V VO = 5.5 V –50 VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V mA mA 3 pF 6 pF * On products compliant to MIL-PRF-38535, this parameter does not apply. † All typical values are at VCC = 5 V. ‡ The parameters IOZH and IOZL include the input leakage current. § This parameter is characterized but not production tested. ¶ Not more than one output should be tested at a time, and the duration of the test should not exceed one second. # This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS234D – SEPTEMBER 1992 – REVISED MAY 1997 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tPLH tPHL A B tPLH tPHL B A tPZH tPZL OE A tPHZ tPLZ OE A tPZH tPZL OE B tPHZ tPLZ OE B PARAMETER 6 POST OFFICE BOX 655303 VCC = 5 V, TA = 25°C SN54ABT2245 SN74ABT2245 MIN TYP MAX MIN MAX MIN MAX 1 2.5 3.4 1 4 1 3.8 1 3.2 4.2 1 4.6 1 4.5 1 2.2 3.2 1 3.8 1 3.6 1 2.7 3.6 1 4.2 1 4 1 3.3 4.6 1 5.6 1 5.5 1 3.2 4.7 1 6 1 5.7 2 4 5.1 2 5.7 2 5.6 1 2.9 4 1 4.6 1 4.5 1.5 3.6 4.9 1.5 6.3 1.5 6.1 1.5 3.9 5.3 1.5 6.6 1.5 6.3 1.5 3.6 4.7 1.5 5.5 1.5 5.3 1.5 3.3 4.4 1.5 4.9 1.5 4.8 • DALLAS, TEXAS 75265 UNIT ns ns ns ns ns ns SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS SCBS234D – SEPTEMBER 1992 – REVISED MAY 1997 PARAMETER MEASUREMENT INFORMATION 500 Ω From Output Under Test S1 7V Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open 3V LOAD CIRCUIT Timing Input 1.5 V 0V tw tsu 3V th 3V 1.5 V Input 1.5 V Data Input 0V 1.5 V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION 3V 3V 1.5 V Input Output Control 1.5 V 0V 1.5 V 1.5 V VOL tPLH tPHL VOH Output 1.5 V 1.5 V VOL 1.5 V 0V tPLZ Output Waveform 1 S1 at 7 V (see Note B) VOH Output 1.5 V tPZL tPHL tPLH 1.5 V Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 3.5 V VOL + 0.3 V VOL tPHZ tPZH 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 5962-9560601Q2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629560601Q2A SNJ54 ABT2245FK 5962-9560601QRA ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9560601QR A SNJ54ABT2245J 5962-9560601QSA ACTIVE CFP W 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9560601QS A SNJ54ABT2245W SN74ABT2245DBR ACTIVE SSOP DB 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AA245 Samples SN74ABT2245DBRG4 ACTIVE SSOP DB 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AA245 Samples SN74ABT2245DW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ABT2245 Samples SN74ABT2245DWR ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ABT2245 Samples SN74ABT2245N ACTIVE PDIP N 20 20 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74ABT2245N Samples SN74ABT2245PW ACTIVE TSSOP PW 20 70 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AA245 Samples SN74ABT2245PWR ACTIVE TSSOP PW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AA245 Samples SNJ54ABT2245FK ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629560601Q2A SNJ54 ABT2245FK SNJ54ABT2245J ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9560601QR A SNJ54ABT2245J SNJ54ABT2245W ACTIVE CFP W 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9560601QS A SNJ54ABT2245W (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. Addendum-Page 1 Samples Samples Samples Samples Samples Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of