SN74AC11D


      
   
SCAS532D − AUGUST 1995 − REVISED OCTOBER 2003 D 2-V to 6-V VCC Operation D Inputs Accept Voltages to 6 V D Max tpd of 7.5 ns at 5 V 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 1C 1Y 3A 3B 3C 3Y 2A NC 2B NC 2C 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 1Y NC 3A NC 3B 2Y GND NC 3Y 3C 1A 1B 2A 2B 2C 2Y GND SN54AC11 . . . FK PACKAGE (TOP VIEW) 1B 1A NC VCC 1C SN54AC11 . . . J OR W PACKAGE SN74AC11 . . . D, DB, N, NS, OR PW PACKAGE (TOP VIEW) NC − No internal connection description/ordering information The ’AC11 devices contain three independent 3-input AND gates. These devices perform the Boolean function Y = A • B • C or Y = A + B + C in positive logic. ORDERING INFORMATION PDIP − N SN74AC11N Tube SN74AC11D Tape and reel SN74AC11DR SOP − NS Tape and reel SN74AC11NSR AC11 SSOP − DB Tape and reel SN74AC11DBR AC11 Tube SN74AC11PW Tape and reel SN74AC11PWR CDIP − J Tube SNJ54AC11J SNJ54AC11J CFP − W Tube SNJ54AC11W SNJ54AC11W LCCC − FK Tube SNJ54AC11FK SNJ54AC11FK TSSOP − PW −55°C −55 C to 125 125°C C TOP-SIDE MARKING Tube SOIC − D −40°C −40 C to 85 85°C C ORDERABLE PART NUMBER PACKAGE† TA SN74AC11N AC11 AC11 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (each gate) INPUTS A B C OUTPUT Y H H H H L X X L X L X L X X L L Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2003, Texas Instruments Incorporated       !"#   $"%&! '#( '"! !  $#!! $# )# #  #* "# '' +,( '"! $!#- '#  #!#&, !&"'# #-  && $##(  $'"! !$&  . /0 && $## # ##' "&# )#+# #'(  && )# $'"! $'"! $!#- '#  #!#&, !&"'# #-  && $##( POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 

      
   
SCAS532D − AUGUST 1995 − REVISED OCTOBER 2003 logic diagram, each gate (positive logic) 1A 1B 1C 2A 2B 2C 3A 3B 3C 1 2 13 12 3 4 5 6 11 10 9 8 1Y 2Y 3Y Pin numbers shown are for the D, DB, J, N, NS, PW, and W packages. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±200 mA Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 

      
   
SCAS532D − AUGUST 1995 − REVISED OCTOBER 2003 recommended operating conditions (see Note 3) VCC Supply voltage VIH VCC = 3 V VCC = 4.5 V High-level input voltage VCC = 5.5 V VCC = 3 V VIL Input voltage Low-level output current ∆t /∆v MAX MIN MAX 2 6 2 6 2.1 2.1 3.15 3.15 3.85 3.85 0 High-level output current IOL MIN 0 Output voltage IOH SN74AC11 VCC = 4.5 V VCC = 5.5 V Low-level input voltage VI VO SN54AC11 0.9 1.35 1.35 1.65 1.65 0 0 VCC VCC VCC = 3 V VCC = 4.5 V −12 −12 −24 −24 VCC = 5.5 V VCC = 3 V −24 −24 12 12 VCC = 4.5 V VCC = 5.5 V 24 24 24 24 8 8 Input transition rise or fall rate V V 0.9 VCC VCC UNIT V V V mA mA ns / V TA Operating free-air temperature −55 125 −40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = −50 µA VOH IOH = −12 mA IOH = −24 mA IOH = −50 mA† IOH = −75 mA† SN54AC11 SN74AC11 MIN MIN MIN 3V 2.9 2.99 2.9 2.9 4.5 V 4.4 4.49 4.4 4.4 5.5 V 5.4 5.49 5.4 5.4 3V 2.56 2.4 2.46 4.5 V 3.86 3.7 3.76 5.5 V 4.86 4.7 4.76 5.5 V MAX IOL = 12 mA IOL = 24 mA 3.85 0.002 0.1 0.1 0.1 4.5 V 0.001 0.1 0.1 0.1 5.5 V 0.001 0.1 0.1 0.1 3V 0.36 0.5 0.44 4.5 V 0.36 0.5 0.44 5.5 V 0.36 0.5 0.44 5.5 V II ICC VI = VCC or GND VI = VCC or GND, 5.5 V Ci VI = VCC or GND V 1.65 5.5 V 1.65 5.5 V 5V UNIT V 3V IOL = 50 mA† IOL = 75 mA† IO = 0 MAX 3.85 5.5 V IOL = 50 µA VOL TA = 25°C TYP MAX VCC ±0.1 ±1 ±1 µA 2 40 20 µA 2.6 pF † Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 

      
   
SCAS532D − AUGUST 1995 − REVISED OCTOBER 2003 switching characteristics over recommended operating free-air temperature range, VCC = 3.3 V " 0.3 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A, B, or C Y TA = 25°C MIN TYP MAX SN54AC11 SN74AC11 MIN MAX MIN MAX 1.5 5.5 9.5 1 11 1 10 1.5 5.5 8.5 1 10.5 1 9.5 UNIT ns switching characteristics over recommended operating free-air temperature range, VCC = 5 V " 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A, B, or C Y MIN TA = 25°C TYP MAX SN54AC11 SN74AC11 MIN MAX MIN MAX 1.5 4 1.5 4 8 1 8.5 1 8.5 7 1 8 1 7.5 UNIT ns operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance CL = 50 pF, f = 1 MHz TYP UNIT 20 pF PARAMETER MEASUREMENT INFORMATION TEST tPLH/tPHL S1 Open From Output Under Test CL = 50 pF (see Note A) S1 Open 50% VCC 50 % VCC 0V tPHL tPLH 2 × VCC 500 Ω VCC Input (see Note B) In-Phase Output 50% VCC tPLH tPHL 500 Ω Out-of-Phase Output LOAD CIRCUIT VOH 50% VCC VOL 50% VCC VOH 50% VCC VOL VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr v 2.5 ns, tf v 2.5 ns. C. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 10-Jun-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 5962-87611012A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 596287611012A SNJ54AC 11FK 5962-8761101CA ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8761101CA SNJ54AC11J Samples 5962-8761101DA ACTIVE CFP W 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8761101DA SNJ54AC11W Samples SN74AC11D ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC11 Samples SN74AC11DBR ACTIVE SSOP DB 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC11 Samples SN74AC11DR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC11 Samples SN74AC11DRE4 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC11 Samples SN74AC11N ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74AC11N Samples SN74AC11PW ACTIVE TSSOP PW 14 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC11 Samples SN74AC11PWR ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC11 Samples SNJ54AC11FK ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 596287611012A SNJ54AC 11FK SNJ54AC11J ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8761101CA SNJ54AC11J Samples SNJ54AC11W ACTIVE CFP W 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8761101DA SNJ54AC11W Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples Samples PACKAGE OPTION ADDENDUM www.ti.com 10-Jun-2022 (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of