SN74AC241N

SN54AC241, SN74AC241 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS513E − JUNE 1995 − REVISED OCTOBER 2003 D 2-V to 6-V VCC Operation D Inputs Accept Voltages to 6 V D Max tpd of 7.5 ns at 5 V SN54AC241 . . . J OR W PACKAGE SN54AC241 . . . DB, DW, N, NS, OR PW PACKAGE (TOP VIEW) 1OE 1A1 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND description/ordering information These octal buffers and line drivers are designed specifically to improve the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. The ’AC241 devices are organized as two 4-bit buffers/drivers with separate complementary output-enable (1OE and 2OE) inputs. When 1OE is low or 2OE is high, the device passes noninverted data from the A inputs to the Y outputs. When 1OE is high or 2OE is low, the outputs are in the high-impedance state. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 2OE 1Y1 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor and OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by the current-sinking or the current-sourcing capability of the driver. 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 1Y1 2A4 1Y2 2A3 1Y3 2Y1 GND 2A1 1Y4 2A2 1A2 2Y3 1A3 2Y2 1A4 2OE 2Y4 1A1 1OE VCC SN54AC241 . . . FK PACKAGE (TOP VIEW) ORDERING INFORMATION PDIP − N SN74AC241N Tube SN74AC241DW Tape and reel SN74AC241DWR SOP − NS Tape and reel SN74AC241NSR AC241 SSOP − DB Tape and reel SN74AC241DBR AC241 Tube SN74AC241PW Tape and reel SN74AC241PWR CDIP − J Tube SNJ54AC241J SNJ54AC241J CFP − W Tube SNJ54AC241W SNJ54AC241W LCCC − FK Tube SNJ54AC241FK SNJ54AC241FK TSSOP − PW −55°C 55 C to 125 125°C C † TOP-SIDE MARKING Tube SOIC − DW −40°C 40 C to 85°C 85 C ORDERABLE PART NUMBER PACKAGE† TA SN74AC241N AC241 AC241 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright © 2003, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54AC241, SN74AC241 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS513E − JUNE 1995 − REVISED OCTOBER 2003 FUNCTION TABLES INPUTS 1OE 1A OUTPUT 1Y L H H L L L H X Z INPUTS 2OE 2A OUTPUT 2Y H H H H L L L X Z logic diagram (positive logic) 1OE 1A1 1A2 1A3 1A4 1 2OE 2 18 4 16 6 14 8 12 1Y1 2A1 1Y2 2A2 1Y3 2A3 1Y4 2A4 19 11 9 13 7 15 5 17 3 2Y1 2Y2 2Y3 2Y4 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±200 mA Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54AC241, SN74AC241 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS513E − JUNE 1995 − REVISED OCTOBER 2003 recommended operating conditions (see Note 3) SN54AC241 VCC Supply voltage VCC = 3 V VIH VIL High-level High level input voltage Low-level Low level input voltage VI Input voltage VO Output voltage IOH IOL High-level High level output current Low-level Low level output current Δt/Δv Input transition rise or fall rate TA Operating free-air temperature MIN MAX 2 6 SN74AC241 MIN MAX 2 6 2.1 2.1 VCC = 4.5 V 3.15 3.15 VCC = 5.5 V 3.85 3.85 UNIT V V VCC = 3 V 0.9 0.9 VCC = 4.5V 1.35 1.35 VCC = 5.5 V 1.65 1.65 V 0 VCC 0 VCC V 0 VCC 0 VCC V VCC = 3 V −12 −12 VCC = 4.5 V −24 −24 VCC = 5.5 V −24 −24 VCC = 3 V 12 12 VCC = 4.5 V 24 24 VCC = 5.5 V 24 24 8 8 ns/V 85 °C −55 125 −40 mA mA NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54AC241, SN74AC241 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS513E − JUNE 1995 − REVISED OCTOBER 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC IOH = −50 50 μA IOH = −12 mA VOH IOH = −24 24 mA † MAX SN74AC241 MIN 3V 2.9 2.9 2.9 4.5 V 4.4 4.4 4.4 5.5 V 5.4 5.4 5.4 3V 2.56 2.4 2.46 4.5 V 3.86 3.7 3.76 5.5 V 4.86 4.7 4.76 MAX 3V 0.1 0.1 0.1 IOL = 50 μA 4.5 V 0.1 0.1 0.1 5.5 V 0.1 0.1 0.1 3.85 3V 0.36 0.5 0.44 0.36 0.5 0.44 5.5 V 0.36 0.5 0.44 5.5 V IOL = 75 mA† 5.5 V VI = VCC or GND 3.85 4.5 V mA† IOZ VO = VCC or GND, VI(OE) = VIL or VIH ICC VI = VCC or GND, Ci VI = VCC or GND IO = 0 V 1.65 1.65 ±0.1 ±1 ±1 ±0.1 ±1 ±1 5.5 V ±0.25 ±5 ±2.5 μA 5.5 V 4 80 40 μA 55V 5.5 VI = VCC or GND UNIT V 5.5 V IOL = 50 Control inputs MIN 5.5 V IOL = 24 mA II SN54AC241 MAX IOH = −75 mA† IOL = 12 mA Data inputs TYP mA† IOH = −50 VOL TA = 25°C MIN 5V 2.5 A μA pF Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms. switching characteristics over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1) PARAMETER tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A Y OE or OE Y OE or OE Y TA = 25°C TYP MAX MIN 1.5 6 9 1.5 6 9 1.5 6.5 1.5 7 2 1.5 POST OFFICE BOX 655303 SN74AC241 MAX MIN 1 12 1.5 10 1 11.5 1 10.5 12.5 1 13 1 13 12 1 13 1.5 13 8 12 1 13 2 12.5 7 12.5 1 13 1 13.5 PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 SN54AC241 MIN • DALLAS, TEXAS 75265 MAX UNIT ns ns ns SN54AC241, SN74AC241 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS513E − JUNE 1995 − REVISED OCTOBER 2003 switching characteristics over recommended operating VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A Y OE or OE Y OE or OE Y free-air TA = 25°C MIN temperature SN54AC241 range, SN74AC241 TYP MAX MIN MAX MIN MAX 1.5 5 7 1 9.5 1 7.5 1.5 4.5 7 1 9 1 7.5 1.5 5.5 9 1 10 1 9.5 1.5 5.5 9 1 10 1 9.5 1.5 6.5 10 1 11.5 1 10.5 1.5 6 10 1 11.5 1 10.5 UNIT ns ns ns operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance per buffer/driver CL = 50 pF, TYP f = 1 MHz 45 UNIT pF PARAMETER MEASUREMENT INFORMATION 2 × VCC S1 500 Ω From Output Under Test CL = 50 pF (see Note A) Open 500 Ω Output Control (low-level enabling) LOAD CIRCUIT VCC Input 50% VCC 50% VCC 0V tPLH tPHL 50% VCC S1 Open 2 × VCC Open VCC 50% VCC 50% VCC VOL 50% VCC 0V tPZL tPLZ Output Waveform 1 S1 at 2 × VCC (see Note B) ≈VCC 50% VCC tPZH VOH Output TEST tPLH/tPHL tPLZ/tPZL tPHZ/tPZH VOL tPHZ Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS VOL + 0.3 V 50% VCC VOH − 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74AC241DBR ACTIVE SSOP DB 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC241 SN74AC241DW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC241 SN74AC241DWR ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC241 SN74AC241N ACTIVE PDIP N 20 20 RoHS & Non-Green NIPDAU N / A for Pkg Type -40 to 85 SN74AC241N SN74AC241NSR ACTIVE SO NS 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC241 SN74AC241PW ACTIVE TSSOP PW 20 70 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC241 SN74AC241PWR ACTIVE TSSOP PW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC241 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of