SN74AC86PWE4


     
 
SCAS533C − AUGUST 1995 − REVISED OCTOBER 2003 D 2-V to 6-V VCC Operation D Inputs Accept Voltages to 6 V D Max tpd of 9 ns at 5 V SN54AC86 . . . FK PACKAGE (TOP VIEW) 1A 1B 1Y 2A 2B 2Y GND 1 14 2 13 3 12 4 11 5 6 9 8 VCC 4B 4A 4Y 3B 3A 3Y 1Y NC 2A NC 2B 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4A NC 4Y NC 3B 2Y GND NC 3Y 3A 7 10 1B 1A NC VCC 4B SN54AC86 . . . J OR W PACKAGE SN74AC86 . . . D, DB, N, NS, OR PW PACKAGE (TOP VIEW) NC − No internal connection description/ordering information The ’AC86 devices are quadruple 2-input exclusive-OR gates. The devices perform the Boolean function Y = A  B or Y = AB + AB in positive logic. A common application is as a true/complement element. If one of the inputs is low, the other input is reproduced in true form at the output. If one of the inputs is high, the signal on the other input is reproduced inverted at the output. ORDERING INFORMATION PDIP − N SN74AC86N Tube SN74AC86D Tape and reel SN74AC86DR SOP − NS Tape and reel SN74AC86NSR AC86 SSOP − DB Tape and reel SN74AC86DBR AC86 Tube SN74AC86PW Tape and reel SN74AC86PWR CDIP − J Tube SNJ54AC86J SNJ54AC86J CFP − W Tube SNJ54AC86W SNJ54AC86W LCCC − FK Tube SNJ54AC86FK SNJ54AC86FK TSSOP − PW −55°C −55 C to 125 125°C C TOP-SIDE MARKING Tube SOIC − D −40°C −40 C to 85 85°C C ORDERABLE PART NUMBER PACKAGE† TA SN74AC86N AC86 AC86 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2003, Texas Instruments Incorporated    !" # $%&" !#  '%()$!" *!"&+ *%$"# $ " #'&$$!"# '& ",& "&#  &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0  !)) '!!&"&#+  '*%$"# $')!" " 1233 !)) '!!&"&# !& "&#"&* %)&## ",&.#& "&*+  !)) ",& '*%$"# '*%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0  !)) '!!&"&#+ POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 

     
 
SCAS533C − AUGUST 1995 − REVISED OCTOBER 2003 FUNCTION TABLE (each gate) INPUTS A OUTPUT Y B L L L L H H H L H H H L exclusive-OR logic An exclusive-OR gate has many applications, some of which can be represented better by alternative logic symbols. EXCLUSIVE OR =1 These five equivalent exclusive-OR symbols are valid for an ’AC86 gate in positive logic; negation may be shown at any two ports. LOGIC-IDENTITY ELEMENT EVEN-PARITY ELEMENT = 2k The output is active (low) if all inputs stand at the same logic level (i.e., A = B). The output is active (low) if an even number of inputs (i.e., 0 or 2) are active. ODD-PARITY ELEMENT 2k + 1 The output is active (high) if an odd number of inputs (i.e., only 1 of the 2) are active. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 

     
 
SCAS533C − AUGUST 1995 − REVISED OCTOBER 2003 recommended operating conditions (see Note 3) VCC VIH Supply voltage VCC = 3 V VCC = 4.5 V High-level input voltage VCC = 5.5 V VCC = 3 V VIL VI VO IOH IOL ∆t/∆v SN54AC86 SN74AC86 MIN MAX MIN MAX 2 6 2 6 2.1 2.1 3.15 3.15 3.85 3.85 VCC = 4.5 V VCC = 5.5 V Low-level input voltage Input voltage 0 Output voltage 0 High-level output current Low-level output current 0.9 1.35 1.35 1.65 1.65 0 0 VCC VCC VCC = 3 V VCC = 4.5 V −12 −12 −24 −24 VCC = 5.5 V VCC = 3 V −24 −24 12 12 VCC = 4.5 V VCC = 5.5 V 24 24 24 24 8 8 Input transition rise or fall rate V V 0.9 VCC VCC UNIT V V V mA mA ns/V TA Operating free-air temperature −55 125 −40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = −50 µA VOH IOH = −12 mA IOH = −24 mA IOH = −50 mA† IOH = −75 mA† MIN TA = 25°C TYP MAX SN54AC86 SN74AC86 MIN MIN MAX 3V 2.9 2.9 2.9 4.5 V 4.4 4.4 4.4 5.5 V 5.4 5.4 5.4 3V 2.56 2.4 2.46 4.5 V 3.86 3.7 3.76 5.5 V 4.86 4.7 4.76 5.5 V IOL = 12 mA IOL = 24 mA 3.85 0.002 0.1 0.1 0.1 4.5 V 0.001 0.1 0.1 0.1 5.5 V 0.001 0.1 0.1 0.1 3V 0.36 0.5 0.44 4.5 V 0.36 0.5 0.44 5.5 V 0.36 0.5 0.44 5.5 V II ICC VI = VCC or GND VI = VCC or GND, 5.5 V Ci VI = VCC or GND V 1.65 5.5 V 1.65 5.5 V 5V UNIT V 3V IOL = 50 mA† IOL = 75 mA† IO = 0 MAX 3.85 5.5 V IOL = 50 µA VOL VCC ±0.1 ±1 ±1 µA 2 40 20 µA 2.6 pF † Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 

     
 
SCAS533C − AUGUST 1995 − REVISED OCTOBER 2003 switching characteristics over recommended operating free-air temperature range, VCC = 3.3 V " 0.3 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B Y MIN TA = 25°C TYP MAX SN54AC86 SN74AC86 MIN MAX MIN MAX 2 6.5 11.5 1 14 1.5 12.5 2 6 11.5 1 14 1.5 12.5 UNIT ns switching characteristics over recommended operating free-air temperature range, VCC = 5 V " 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B Y MIN TA = 25°C TYP MAX SN54AC86 SN74AC86 MIN MAX MIN MAX 1.5 4.5 8.5 1 10 1 9 1.5 4.5 8.5 1 10 1 9.5 UNIT ns operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd 4 TEST CONDITIONS Power dissipation capacitance CL = 50 pF, POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 f = 1 MHz TYP 25 UNIT pF 

     
 
SCAS533C − AUGUST 1995 − REVISED OCTOBER 2003 PARAMETER MEASUREMENT INFORMATION 2 × VCC S1 500 Ω From Output Under Test CL = 50 pF (see Note A) Open TEST S1 tPLH/tPHL Open 500 Ω LOAD CIRCUIT tw 2.7 V Input 50% VCC 50% VCC 0V VCC 50% VCC Input VOLTAGE WAVEFORMS 50% VCC tPLH tPHL VCC 50% VCC Timing Input 0V tsu Data Input In-Phase Output VCC 50% VCC 50% VCC tPHL th 50% VCC 0V Out-of-Phase Output 0V VOH 50% VCC VOL tPLH 50% VCC VOH 50% VCC VOL VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr v 2.5 ns, tf v 2.5 ns. C. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 5962-89550012A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 596289550012A SNJ54AC 86FK 5962-8955001CA ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8955001CA SNJ54AC86J Samples 5962-8955001DA ACTIVE CFP W 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8955001DA SNJ54AC86W Samples SN74AC86D ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC86 Samples SN74AC86DBR ACTIVE SSOP DB 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC86 Samples SN74AC86DR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC86 Samples SN74AC86DRE4 ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC86 Samples SN74AC86N ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74AC86N Samples SN74AC86NSR ACTIVE SO NS 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC86 Samples SN74AC86PW ACTIVE TSSOP PW 14 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC86 Samples SN74AC86PWG4 ACTIVE TSSOP PW 14 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC86 Samples SN74AC86PWR ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AC86 Samples SNJ54AC86FK ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 596289550012A SNJ54AC 86FK SNJ54AC86J ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8955001CA SNJ54AC86J Samples SNJ54AC86W ACTIVE CFP W 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8955001DA SNJ54AC86W Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. Addendum-Page 1 Samples Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of