SN74ACT533DWRE4

SN54ACT533, SN74ACT533 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS553C – NOVEMBER 1995 – REVISED OCTOBER 2002 SN54ACT533 . . . J OR W PACKAGE SN74ACT533 . . . DB, DW, N, NS, OR PW PACKAGE (TOP VIEW) 4.5-V to 5.5-V VCC Operation Inputs Accept Voltages to 5.5 V Max tpd of 11 ns at 5 V Inputs Are TTL-Voltage Compatible 3-State Inverting Outputs Drive Bus Lines Directly OE 1Q 1D 2D 2Q 3Q 3D 4D 4Q GND description/ordering information The ’ACT533 devices are octal transparent D-type latches with 3-state outputs. When the latch-enable (LE) input is high, the Q outputs follow the complements of the data (D) inputs. When LE is taken low, the Q outputs are latched at the inverted levels set up at the D inputs. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 8Q 8D 7D 7Q 6Q 6D 5D 5Q LE 1D 1Q OE VCC 2D 2Q 3Q 3D 4D 8Q SN54ACT533 . . . FK PACKAGE (TOP VIEW) A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4Q GND LE OE does not affect the internal operations of the latches. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. 8D 7D 7Q 6Q 6D 5Q 5D D D D D D To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION PDIP – N –55°C to 125°C TOP-SIDE MARKING Tube SN74ACT533N Tube SN74ACT533DW Tape and reel SN74ACT533DWR SOP – NS Tape and reel SN74ACT533NSR ACT533 SSOP – DB Tape and reel SN74ACT533DBR AD533 TSSOP – PW Tape and reel SN74ACT533PWR AD533 CDIP – J Tube SNJ54ACT533J SNJ54ACT533J CFP – W Tube SNJ54ACT533W SNJ54ACT533W LCCC – FK Tube SNJ54ACT533K SOIC – DW –40°C 40°C to 85°C ORDERABLE PART NUMBER PACKAGE† TA SN74ACT533N ACT533 SNJ54ACT533FK † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2002, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ACT533, SN74ACT533 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS553C – NOVEMBER 1995 – REVISED OCTOBER 2002 FUNCTION TABLE (each latch) INPUTS OUTPUT Q OE LE D L H H L L H L H L L X Q0 H X X Z logic diagram (positive logic) 1 OE LE 11 C1 1D 2 1Q 3 1D To Seven Other Channels absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±200 mA Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ACT533, SN74ACT533 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS553C – NOVEMBER 1995 – REVISED OCTOBER 2002 recommended operating conditions (see Note 3) SN54ACT533 MAX MIN MAX 4.5 5.5 4.5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 0 VO IOH Output voltage 0 High-level output current IOL ∆t/∆v Low-level output current High-level input voltage SN74ACT533 MIN 2 2 V V 0.8 Input transition rise or fall rate UNIT 0.8 V VCC VCC V –24 –24 mA 24 24 mA 8 8 ns/V VCC VCC 0 0 V TA Operating free-air temperature –55 125 –40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS 4.5 V IOH = –50 50 µA VOH IOH = –24 24 mA IOH = –50 mA† IOH = –75 mA† MIN TA = 25°C TYP MAX SN54ACT533 MIN MAX MIN 4.49 4.4 5.5 V 5.4 5.49 5.4 5.4 4.5 V 3.86 3.7 3.76 5.5 V 4.86 4.7 4.76 MAX UNIT 4.4 V 3.85 5.5 V IOL = 24 mA SN74ACT533 4.4 5.5 V IOL = 50 µA VOL VCC 3.85 4.5 V 0.1 0.1 5.5 V 0.1 0.1 0.1 0.1 4.5 V 0.36 0.5 0.44 5.5 V 0.36 0.5 0.44 V IOL = 50 mA† IOL = 75 mA† 5.5 V IOZ II VO = VCC or GND VI = VCC or GND 5.5 V ±0.25 ±5 ±2.5 µA 5.5 V ±0.1 ±1 ±1 µA ICC VI = VCC or GND, IO = 0 One input at 3.4 V, Other inputs at GND or VCC 5.5 V 4 80 40 µA 1.6 1.5 mA ∆ICC‡ 1.65 5.5 V 5.5 V 1.65 0.6 Ci VI = VCC or GND 5V 4.5 † Not more than one output should be tested at a time, and the duration of the test should not exceed 2 ms. ‡ This is the increase in supply current for each input that is at one of the specified TTL voltage levels, rather than 0 V or VCC. pF timing requirements over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) TA = 25°C MIN MAX SN54ACT533 MIN MAX SN74ACT533 MIN MAX UNIT tw tsu Pulse duration, LE high 5 7.5 6 ns Setup time, data before LE↓ 3 5.5 4 ns th Hold time, data after LE↓ 2 4 2.5 ns PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ACT533, SN74ACT533 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS553C – NOVEMBER 1995 – REVISED OCTOBER 2002 switching characteristics over recommended operating VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL D Q tPLH tPHL LE Q tPZH tPZL OE Q tPHZ tPLZ OE Q free-air TA = 25°C MIN MAX temperature SN54ACT533 MIN SN74ACT533 MAX MIN MAX 2.5 10.5 1.5 13 2 11.5 2.5 10 1.5 12.5 2 11 2.5 10.5 1.5 13 2 11.5 2.5 10.5 1.5 13 2 11.5 2 10 1 12.5 1.5 11 2 10 1 12.5 1.5 11 2 10 1 12.5 1.5 11 2 10 1 12.5 1.5 11 range, UNIT ns ns ns ns operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance CL = 50 pF, PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 f = 1 MHz TYP 40 UNIT pF SN54ACT533, SN74ACT533 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS553C – NOVEMBER 1995 – REVISED OCTOBER 2002 PARAMETER MEASUREMENT INFORMATION 2 × VCC S1 500 Ω From Output Under Test CL = 50 pF (see Note A) Open 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC Open 3V 1.5 V Timing Input LOAD CIRCUIT 0V th tsu 3V 1.5 V Data Input tw 0V 3V 1.5 V Input 1.5 V VOLTAGE WAVEFORMS 1.5 V 0V VOLTAGE WAVEFORMS Output Control (low-level enabling) 3V 1.5 V 1.5 V 0V tPZL 3V Input 1.5 V 1.5 V 0V tPLH Output tPHL 50% VCC VOH 50% VCC VOL Output Waveform 1 S1 at 2 × VCC (see Note B) tPLZ ≈VCC 50% VCC tPZH Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS VOL + 0.3 V VOL tPHZ 50% VCC VOH – 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 11-Jan-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74ACT533DW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ACT533 SN74ACT533N ACTIVE PDIP N 20 20 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74ACT533N SN74ACT533PW ACTIVE TSSOP PW 20 70 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AD533 SN74ACT533PWR ACTIVE TSSOP PW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AD533 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of