SN74ACT86N


      
 
SCAS534C − AUGUST 1995 − REVISED OCTOBER 2003 D 4.5-V to 5.5-V VCC Operation D Inputs Accept Voltages to 5.5 V D Max tpd of 10 ns at 5 V D Inputs Are TTL-Voltage Compatible SN54ACT86 . . . J OR W PACKAGE SN74ACT86 . . . D, DB, N, NS, OR PW PACKAGE (TOP VIEW) 1 14 2 13 3 12 4 11 5 10 6 9 7 8 1B 1A NC VCC 4B VCC 4B 4A 4Y 3B 3A 3Y 1Y NC 2A NC 2B 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4A NC 4Y NC 3B 2Y GND NC 3Y 3A 1A 1B 1Y 2A 2B 2Y GND SN54ACT86 . . . FK PACKAGE (TOP VIEW) NC − No internal connection description/ordering information The ’ACT86 devices are quadruple 2-input exclusive-OR gates. The devices perform the Boolean functions Y = A  B or Y = AB + AB in positive logic. A common application is as a true/complement element. If one of the inputs is low, the other input is reproduced in true form at the output. If one of the inputs is high, the signal on the other input is reproduced inverted at the output. ORDERING INFORMATION PDIP − N SN74ACT86N Tube SN74ACT86D Tape and reel SN74ACT86DR SOP − NS Tape and reel SN74ACT86NSR ACT86 SSOP − DB Tape and reel SN74ACT86DBR AD86 Tube SN74ACT86PW Tape and reel SN74ACT86PWR CDIP − J Tube SNJ54ACT86J SNJ54ACT86J CFP − W Tube SNJ54ACT86W SNJ54ACT86W LCCC − FK Tube SNJ54ACT86FK SNJ54ACT86FK TSSOP − PW −55°C −55 C to 125 125°C C TOP-SIDE MARKING Tube SOIC − D −40°C −40 C to 85 85°C C ORDERABLE PART NUMBER PACKAGE† TA SN74ACT86N ACT86 AD86 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2003, Texas Instruments Incorporated    !" # $%&" !#  '%()$!" *!"&+ *%$"# $ " #'&$$!"# '& ",& "&#  &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0  !)) '!!&"&#+  '*%$"# $')!" " 1233 !)) '!!&"&# !& "&#"&* %)&## ",&.#& "&*+  !)) ",& '*%$"# '*%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0  !)) '!!&"&#+ POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 

      
 
SCAS534C − AUGUST 1995 − REVISED OCTOBER 2003 FUNCTION TABLE (each gate) INPUTS A OUTPUT Y B L L L L H H H L H H H L exclusive-OR logic An exclusive-OR gate has many applications, some of which can be represented better by alternative logic symbols. EXCLUSIVE-OR =1 These five equivalent exclusive-OR symbols are valid for an ’ACT86 gate in positive logic; negation may be shown at any two ports. LOGIC-IDENTITY ELEMENT EVEN-PARITY ELEMENT = 2k The output is active (low) if all inputs stand at the same logic level (i.e., A = B). The output is active (low) if an even number of inputs (i.e., 0 or 2) are active. ODD-PARITY ELEMENT 2k + 1 The output is active (high) if an odd number of inputs (i.e., only 1 of the 2) are active. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±200 mA Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 

      
 
SCAS534C − AUGUST 1995 − REVISED OCTOBER 2003 recommended operating conditions (see Note 3) SN54ACT86 MIN MAX MIN MAX 4.5 5.5 4.5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 0 VO IOH Output voltage 0 High-level output current IOL ∆t/∆v Low-level output current High-level input voltage SN74ACT86 2 2 V V 0.8 Input transition rise or fall rate UNIT 0.8 V VCC VCC V −24 −24 mA 24 24 mA 8 8 ns/V VCC VCC 0 0 V TA Operating free-air temperature −55 125 −40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = −50 µA A VOH IOH = −24 mA IOH = −50 mA† IOH = −75 mA† SN54ACT86 4.5 V 4.4 4.49 4.4 5.5 V 5.4 5.49 5.4 5.4 4.5 V 3.86 3.7 3.76 5.5 V 4.86 4.7 4.76 MIN MAX MIN MAX UNIT 4.4 V 3.85 5.5 V IOL = 24 mA SN74ACT86 MIN 5.5 V IOL = 50 µA A VOL TA = 25°C TYP MAX VCC 3.85 4.5 V 0.001 0.1 0.1 5.5 V 0.001 0.1 0.1 0.1 0.1 4.5 V 0.36 0.5 0.44 5.5 V 0.36 0.5 0.44 V IOL = 50 mA† IOL = 75 mA† 5.5 V II ICC VI = VCC or GND VI = VCC or GND, 5.5 V ±0.1 ±1 ±1 µA 5.5 V 4 80 40 µA ∆ICC‡ One input at 3.4 V, Other inputs at GND or VCC 1.6 1.5 mA 1.65 5.5 V IO = 0 1.65 5.5 V 0.6 Ci VI = VCC or GND 5V 2.6 † Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms. ‡ This is the increase in supply current for each input that is at one of the specified TTL voltage levels, rather than 0 V or VCC. pF switching characteristics over recommended operating free-air temperature range, VCC = 5 V " 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B Y POST OFFICE BOX 655303 TA = 25°C MIN TYP MAX SN54ACT86 MIN SN74ACT86 MAX MIN MAX 1.5 8.5 9.5 1 10 1 10 1.5 7 9.5 1 10.5 1 10.5 • DALLAS, TEXAS 75265 UNIT ns 3 

      
 
SCAS534C − AUGUST 1995 − REVISED OCTOBER 2003 operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance CL = 50 pF, f = 1 MHz TYP 25 UNIT pF PARAMETER MEASUREMENT INFORMATION TEST tPLH/tPHL S1 Open From Output Under Test CL = 50 pF (see Note A) S1 Open 1.5 V 1.5 V 0V tPHL tPLH 2 × VCC 500 Ω 3V Input (see Note B) In-Phase Output 50% VCC tPLH tPHL 500 Ω Out-of-Phase Output LOAD CIRCUIT VOH 50% VCC VOL 50% VCC VOH 50% VCC VOL VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr v 2.5 ns, tf v 2.5 ns. C. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 5962-9068701Q2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629068701Q2A SNJ54ACT 86FK 5962-9068701QCA ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9068701QC A SNJ54ACT86J 5962-9068701QDA ACTIVE CFP W 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9068701QD A SNJ54ACT86W SN74ACT86D ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ACT86 Samples SN74ACT86DBR ACTIVE SSOP DB 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AD86 Samples SN74ACT86DR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ACT86 Samples SN74ACT86N ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74ACT86N Samples SN74ACT86NSR ACTIVE SO NS 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 ACT86 Samples SN74ACT86PW ACTIVE TSSOP PW 14 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AD86 Samples SN74ACT86PWR ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AD86 Samples SN74ACT86PWRG4 ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 AD86 Samples SNJ54ACT86FK ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 59629068701Q2A SNJ54ACT 86FK SNJ54ACT86J ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9068701QC A SNJ54ACT86J SNJ54ACT86W ACTIVE CFP W 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-9068701QD A SNJ54ACT86W Addendum-Page 1 Samples Samples Samples Samples Samples Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of