SN74ALS05AN

SN54ALS05A, SN74ALS05A HEX INVERTERS WITH OPEN-COLLECTOR OUTPUTS SDAS190A – APRIL 1982 – REVISED DECEMBER 1994 SN54ALS05A . . . J PACKAGE SN74ALS05A . . . D OR N PACKAGE (TOP VIEW) Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 300-mil DIPs 1A 1Y 2A 2Y 3A 3Y GND description These devices contain six independent hex inverters with open-collector outputs. They perform the Boolean function Y = A. The open-collector outputs require pullup resistors to perform correctly. These outputs can be connected to other open-collector outputs to implement active-low wired-OR or active-high wired-AND functions. Open-collector devices are often used to generate higher VOH levels. L L H 2A 3A 4A 5A 6A 1 12 4 11 5 10 6 9 7 8 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 6Y NC 5A NC 5Y NC – No internal connection logic symbol† 1A 3 VCC 6A 6Y 5A 5Y 4A 4Y 3Y GND NC 4Y 4A H 13 1Y 1A NC VCC 2A NC 2Y NC 3A FUNCTION TABLE (each inverter) OUTPUT Y 14 2 SN54ALS05A . . . FK PACKAGE (TOP VIEW) The SN54ALS05A is characterized for operation over the full military temperature range of – 55°C to 125°C. The SN74ALS05A is characterized for operation from 0°C to 70°C. INPUT A 1 6A • logic diagram (positive logic) 1 2 3 4 5 6 9 8 11 10 13 12 1Y 1A 1 2 3 4 5 6 9 8 11 10 13 12 1Y 2Y 3Y 2A 2Y 4Y 5Y 3A 3Y 6Y † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the D, J, and N packages. 4A 5A 6A 4Y 5Y 6Y Copyright  1994, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ALS05A, SN74ALS05A HEX INVERTERS WITH OPEN-COLLECTOR OUTPUTS SDAS190A – APRIL 1982 – REVISED DECEMBER 1994 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Operating free-air temperature range, TA: SN54ALS05A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C SN74ALS05A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. recommended operating conditions SN54ALS05A SN74ALS05A MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 UNIT VCC VIH Supply voltage VIL VOH Low-level input voltage 0.7 0.8 High-level output voltage 5.5 5.5 IOL TA Low-level output current 4 8 mA 70 °C High-level input voltage 2 Operating free-air temperature 2 – 55 125 V V 0 V V electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER SN54ALS05A TYP‡ MAX TEST CONDITIONS VIK VCC = 4.5 V, VOL 5V VCC = 4 4.5 II IIH VCC = 5.5 V, VCC = 5.5 V, IIL IOH VCC = 5.5 V, VCC = 4.5 V, ICCH ICCL VCC = 5.5 V, VCC = 5.5 V, MIN II = –18 mA IOL = 4 mA SN74ALS05A TYP‡ MAX MIN –1.2 0.25 IOL = 8 mA VI = 7 V VI = 2.7 V VI = 0.4 V VOH = 5.5 V VI = 0 –1.2 0.4 0.25 0.4 0.35 0.5 V V 0.1 0.1 20 20 µA – 0.1 – 0.1 mA 0.1 VI = 4.5 V UNIT mA 0.1 mA 0.65 1.1 0.65 1.1 mA 2.9 4.2 2.9 4.2 mA ‡ All typical values are at VCC = 5 V, TA = 25°C. switching characteristics (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) VCC = 4.5 V to 5.5 V, CL = 50 pF, RL = 2 kΩ, TA = MIN to MAX§ SN54ALS05A tPLH tPHL A Y SN74ALS05A MIN MAX MIN MAX 23 84 23 54 4 24 4 14 § For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT ns SN54ALS05A, SN74ALS05A HEX INVERTERS WITH OPEN-COLLECTOR OUTPUTS SDAS190A – APRIL 1982 – REVISED DECEMBER 1994 PARAMETER MEASUREMENT INFORMATION SERIES 54ALS/74ALS AND 54AS/74AS DEVICES 7V RL = R1 = R2 VCC S1 RL R1 Test Point From Output Under Test CL (see Note A) From Output Under Test RL Test Point From Output Under Test CL (see Note A) CL (see Note A) LOAD CIRCUIT FOR BI-STATE TOTEM-POLE OUTPUTS LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS 3.5 V Timing Input Test Point LOAD CIRCUIT FOR 3-STATE OUTPUTS 3.5 V High-Level Pulse 1.3 V R2 1.3 V 1.3 V 0.3 V 0.3 V Data Input tw th tsu 3.5 V 1.3 V 3.5 V Low-Level Pulse 1.3 V 0.3 V 1.3 V 0.3 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATIONS 3.5 V Output Control (low-level enabling) 1.3 V 1.3 V 0.3 V tPZL Waveform 1 S1 Closed (see Note B) tPLZ [3.5 V 1.3 V tPHZ tPZH Waveform 2 S1 Open (see Note B) 1.3 V VOL 0.3 V VOH 1.3 V 0.3 V [0 V 3.5 V 1.3 V Input 1.3 V 0.3 V tPHL tPLH VOH In-Phase Output 1.3 V 1.3 V VOL tPLH tPHL VOH Out-of-Phase Output (see Note C) 1.3 V 1.3 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. When measuring propagation delay items of 3-state outputs, switch S1 is open. D. All input pulses have the following characteristics: PRR ≤ 1 MHz, tr = tf = 2 ns, duty cycle = 50%. E. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuits and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 5962-88540012A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 596288540012A SNJ54ALS 05AFK 5962-8854001CA ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8854001CA SNJ54ALS05AJ Samples 5962-8854001DA ACTIVE CFP W 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8854001DA SNJ54ALS05AW Samples SN54ALS05AJ ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SN54ALS05AJ Samples SN74ALS05AD ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS05A Samples SN74ALS05ADG4 ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS05A Samples SN74ALS05ADR ACTIVE SOIC D 14 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS05A Samples SN74ALS05AN ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN74ALS05AN Samples SN74ALS05ANSR ACTIVE SO NS 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS05A Samples SNJ54ALS05AFK ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 596288540012A SNJ54ALS 05AFK SNJ54ALS05AJ ACTIVE CDIP J 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8854001CA SNJ54ALS05AJ Samples SNJ54ALS05AW ACTIVE CFP W 14 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8854001DA SNJ54ALS05AW Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of