SN74ALVC162835
18-BIT UNIVERSAL BUS DRIVER
WITH 3-STATE OUTPUTS
www.ti.com
SCES126H – FEBRUARY 1998 – REVISED SEPTEMBER 2004
FEATURES
•
•
•
•
•
•
•
•
DGG, DGV, OR DL PACKAGE
(TOP VIEW)
Member of the Texas Instruments Widebus™
Family
Operates From 1.65 V to 3.6 V
Max tpd of 2 ns at 3.3 V
±12-mA Output Drive at 3.3 V
Ideal for Use in PC100 Register DIMM,
Revision 1.1
Output Port Has Equivalent 26-Ω Series
Resistors, So No External Resistors Are
Required
Latch-Up Performance Exceeds 250 mA Per
JESD 17
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
NC
NC
Y1
GND
Y2
Y3
VCC
Y4
Y5
Y6
GND
Y7
Y8
Y9
Y10
Y11
Y12
GND
Y13
Y14
Y15
VCC
Y16
Y17
GND
Y18
OE
LE
DESCRIPTION/ORDERING INFORMATION
This 18-bit universal bus driver is designed for 1.65-V
to 3.6-V VCC operation.
Data flow from A to Y is controlled by the
output-enable (OE) input. The device operates in the
transparent mode when the latch-enable (LE) input is
high. When LE is low, the A data is latched if the
clock (CLK) input is held at a high or low logic level. If
LE is low, the A data is stored in the latch/flip-flop on
the low-to-high transition of CLK. When OE is high,
the outputs are in the high-impedance state.
To ensure the high-impedance state during power up
or power down, OE should be tied to VCC through a
pullup resistor; the minimum value of the resistor is
determined by the current-sinking capability of the
driver.
1
56
2
55
3
54
4
53
5
52
6
51
7
50
8
49
9
48
10
47
11
46
12
45
13
44
14
43
15
42
16
41
17
40
18
39
19
38
20
37
21
36
22
35
23
34
24
33
25
32
26
31
27
30
28
29
GND
NC
A1
GND
A2
A3
VCC
A4
A5
A6
GND
A7
A8
A9
A10
A11
A12
GND
A13
A14
A15
VCC
A16
A17
GND
A18
CLK
GND
NC − No internal connection
The output port includes equivalent 26-Ω series
resistors to reduce overshoot and undershoot.
ORDERING INFORMATION
PACKAGE (1)
TA
(1)
TOP-SIDE MARKING
SN74ALVC162835DL
Tape and reel
SN74ALVC162835DLR
TSSOP - DGG
Tape and reel
SN74ALVC162835DGGR
ALVC162835
TVSOP - DGV
Tape and reel
SN74ALVC162835DGVR
VC2835
SSOP - DL
-40°C to 85°C
ORDERABLE PART NUMBER
Tube
ALVC162835
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1998–2004, Texas Instruments Incorporated
SN74ALVC162835
18-BIT UNIVERSAL BUS DRIVER
WITH 3-STATE OUTPUTS
www.ti.com
SCES126H – FEBRUARY 1998 – REVISED SEPTEMBER 2004
FUNCTION TABLE
INPUTS
(1)
OE
LE
CLK
A
OUTPUT
Y
H
X
X
X
Z
L
H
X
L
L
L
H
X
H
H
L
L
↑
L
L
L
L
↑
H
H
L
L
L or H
X
Y0 (1)
Output level before the indicated steady-state input conditions were
established
LOGIC DIAGRAM (POSITIVE LOGIC)
OE
CLK
LE
A1
27
30
28
54
1D
C1
3
Y1
CLK
To 17 Other Channels
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range
-0.5
4.6
V
VI
Input voltage range (2)
-0.5
4.6
V
-0.5
VCC + 0.5
range (2) (3)
UNIT
VO
Output voltage
IIK
Input clamp current
VI < 0
-50
mA
IOK
Output clamp current
VO < 0
-50
mA
IO
Continuous output current
±50
mA
±100
mA
Continuous current through each VCC or GND
θJA
Package thermal impedance (4)
Tstg
Storage temperature range
DGG package
64
DGV package
48
DL package
(1)
(2)
(3)
(4)
2
V
°C/W
56
-65
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
This value is limited to 4.6 V maximum.
The package thermal impedance is calculated in accordance with JESD 51-7.
SN74ALVC162835
18-BIT UNIVERSAL BUS DRIVER
WITH 3-STATE OUTPUTS
www.ti.com
SCES126H – FEBRUARY 1998 – REVISED SEPTEMBER 2004
RECOMMENDED OPERATING CONDITIONS (1)
VCC
Supply voltage
VCC = 1.65 V to 1.95 V
VIH
High-level input voltage
MIN
MAX
1.65
3.6
Low-level input voltage
VI
Input voltage
VO
Output voltage
IOH
High-level output current
VCC = 2.3 V to 2.7 V
1.7
VCC = 2.7 V to 3.6 V
2
Low-level output current
∆t/∆v
Input transition rise or fall rate
TA
Operating free-air temperature
VCC = 2.3 V to 2.7 V
0.7
VCC = 2.7 V to 3.6 V
0.8
V
0
3.6
V
0
VCC
V
VCC = 1.65 V
-2
VCC = 2.3 V
-6
VCC = 2.7 V
-8
mA
-12
VCC = 1.65 V
2
VCC = 2.3 V
6
VCC = 2.7 V
8
VCC = 3 V
(1)
V
0.35 × VCC
VCC = 3 V
IOL
V
0.65 × VCC
VCC = 1.65 V to 1.95 V
VIL
UNIT
mA
12
-40
10
ns/V
85
°C
All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
3
SN74ALVC162835
18-BIT UNIVERSAL BUS DRIVER
WITH 3-STATE OUTPUTS
www.ti.com
SCES126H – FEBRUARY 1998 – REVISED SEPTEMBER 2004
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IOH = -100 µA
VOH
1.65 V to 3.6 V
MAX
1.65 V
1.2
IOH = -4 mA
2.3 V
1.9
2.3 V
1.7
3V
2.4
IOH = -8 mA
2.7 V
2
IOH = -12 mA
3V
2
IOL = 100 µA
V
1.65 V to 3.6 V
0.2
IOL = 2 mA
1.65 V
0.45
IOL = 4 mA
2.3 V
0.4
2.3 V
0.55
3V
0.55
IOL = 8 mA
2.7 V
0.6
IOL = 12 mA
3V
0.8
IOL = 6 mA
UNIT
VCC - 0.2
IOH = -2 mA
IOH = -6 mA
VOL
MIN TYP (1)
VCC
V
II
VI = VCC or GND
3.6 V
±5
µA
IOZ
VO = VCC or GND
3.6 V
±10
µA
ICC
VI = VCC or GND,
IO = 0
3.6 V
40
µA
One input at VCC - 0.6 V,
Other inputs at VCC or GND
750
µA
∆ICC
Ci
Control inputs
Data inputs
Co Outputs
(1)
3 V to 3.6 V
VI = VCC or GND
3.3 V
VO = VCC or GND
3.3 V
3.5
pF
5
7
pF
All typical values are at VCC = 3.3 V, TA = 25°C.
TIMING REQUIREMENTS
over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1)
VCC = 1.8 V
MIN
fclock
tw
tsu
th
(1)
4
Setup time
Hold time
MIN
(1)
Clock frequency
Pulse duration
MAX
VCC = 2.5 V
± 0.2 V
MAX
VCC = 2.7 V
MIN MAX
150
VCC = 3.3 V
± 0.3 V
MIN
150
150
LE high
(1)
3.3
3.3
3.3
CLK high or low
(1)
3.3
3.3
3.3
Data before CLK↑
(1)
2.2
2.1
1.7
CLK high
(1)
1.9
1.6
1.5
CLK low
(1)
1.3
1.1
1
(1)
0.6
0.6
0.7
(1)
1.4
1.7
1.4
Data before LE↓
Data after CLK↑
Data after LE↓
CLK high or low
This information was not available at the time of publication.
UNIT
MAX
MHz
ns
ns
ns
SN74ALVC162835
18-BIT UNIVERSAL BUS DRIVER
WITH 3-STATE OUTPUTS
www.ti.com
SCES126H – FEBRUARY 1998 – REVISED SEPTEMBER 2004
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1)
FROM
(INPUT)
PARAMETER
TO
(OUTPUT)
VCC = 1.8 V
MIN
TYP
(1)
fmax
LE
tdis
(1)
OE
MIN
150
150
MAX
UNIT
MIN MAX
150
MHz
5
5
1
4.2
(1)
1.3
5.9
5.8
1.3
5.1
(1)
1.4
6.3
6.1
1.4
5.4
Y
(1)
1.4
6.3
6.5
1.1
5.5
ns
Y
(1)
1
4.9
4.9
1.3
4.5
ns
Y
OE
MIN MAX
VCC = 3.3 V
± 0.3 V
1
CLK
ten
VCC = 2.7 V
(1)
A
tpd
VCC = 2.5 V
± 0.2 V
ns
This information was not available at the time of publication.
SWITCHING CHARACTERISTICS
from 0°C to 85°C, CL = 0 pF
FROM
(INPUT)
PARAMETER
A
tpd (1)
(1)
VCC = 3.3 V
± 0.15 V
TO
(OUTPUT)
MIN
Y
CLK
UNIT
MAX
0.9
2
1.4
2.9
ns
Texas Instruments SPICE simulation data
SWITCHING CHARACTERISTICS
from 0°C to 65°C, CL = 50 pF
FROM
(INPUT)
PARAMETER
A
tpd
VCC = 3.3 V
± 0.15 V
TO
(OUTPUT)
Y
CLK
UNIT
MIN
MAX
1
4
1.9
5
ns
OPERATING CHARACTERISTICS
TA = 25°C
PARAMETER
Cpd
(1)
Power dissipation
capacitance
Outputs enabled
Outputs disabled
TEST CONDITIONS
CL = 0,
f = 10 MHz
VCC = 1.8 V
VCC = 2.5 V
VCC = 3.3 V
TYP
TYP
TYP
(1)
35.5
40
(1)
12.5
14
UNIT
pF
This information was not available at the time of publication.
5
SN74ALVC162835
18-BIT UNIVERSAL BUS DRIVER
WITH 3-STATE OUTPUTS
www.ti.com
SCES126H – FEBRUARY 1998 – REVISED SEPTEMBER 2004
PARAMETER MEASUREMENT INFORMATION
VLOAD
S1
RL
From Output
Under Test
Open
GND
CL
(see Note A)
RL
TEST
S1
tpd
tPLZ/tPZL
tPHZ/tPZH
Open
VLOAD
GND
LOAD CIRCUIT
INPUT
VCC
1.8 V
2.5 V ± 0.2 V
2.7 V
3.3 V ± 0.3 V
VI
tr/tf
VCC
VCC
2.7 V
2.7 V
≤2 ns
≤2 ns
≤2.5 ns
≤2.5 ns
VM
VLOAD
CL
RL
V∆
VCC/2
VCC/2
1.5 V
1.5 V
2 × VCC
2 × VCC
6V
6V
30 pF
30 pF
50 pF
50 pF
1 kΩ
500 Ω
500 Ω
500 Ω
0.15 V
0.15 V
0.3 V
0.3 V
tw
VI
Timing
Input
VM
VM
VM
0V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VM
VM
0V
tPLH
Output
Control
(low-level
enabling)
tPLZ
VLOAD/2
VM
tPZH
VOH
VM
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VM
0V
Output
Waveform 1
S1 at VLOAD
(see Note B)
tPHL
VM
VI
VM
tPZL
VI
Input
VOLTAGE WAVEFORMS
PULSE DURATION
th
VI
Data
Input
VM
0V
0V
tsu
Output
VI
VM
Input
Output
Waveform 2
S1 at GND
(see Note B)
VOL + V∆
VOL
tPHZ
VOH
VM
VOH − V∆
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
Figure 1. Load Circuit and Voltage Waveforms
6
SN74ALVC162835
18-BIT UNIVERSAL BUS DRIVER
WITH 3-STATE OUTPUTS
www.ti.com
SCES126H – FEBRUARY 1998 – REVISED SEPTEMBER 2004
TYPICAL CHARACTERISTICS
0
−0.01
ALVC162835 Pullup
x
PC100 Requirements
I OH − Output Current − mA
−0.02
−0.03
−0.04
−0.05
−0.06
−0.07
−0.08
−0.09
−0.1
0.5
0
1.0
1.5
2.0
2.5
3.0
VOH − Output Voltage − V
Figure 2. IV Characteristics - Pullup
0.12
ALVC162835 Pulldown
x
PC100 Requirements
I OL − Output Current − mA
0.10
0.08
0.06
0.04
0.02
0.00
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
VOL − Output Voltage − V
Figure 3. IV Characteristics - Pulldown
7
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
(3)
Device Marking
(4/5)
(6)
SN74ALVC162835DGGR
ACTIVE
TSSOP
DGG
56
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
ALVC162835
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
很抱歉,暂时无法提供与“SN74ALVC162835DGGR”相匹配的价格&库存,您可以联系我们找货
免费人工找货- 国内价格
- 1+13.84560
- 10+13.48920
- 30+13.24080