SN74AS1032AD


  

   


 SDAS072B − DECEMBER 1982 − REVISED JANUARY 1995 Driver Version of ′AS32 High Capacitive-Drive Capability Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 300-mil DIPs SN54AS1032A . . . J PACKAGE SN74AS1032A . . . D OR N PACKAGE (TOP VIEW) 1A 1B 1Y 2A 2B 2Y GND description These devices contain four independent 2-input positive-OR buffers/drivers. They perform the Boolean functions Y = A + B or Y = A • B in positive logic. H X H X H H L L L 13 3 12 4 11 5 10 6 9 7 8 VCC 4B 4A 4Y 3B 3A 3Y 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4A NC 4Y NC 3B 2Y GND NC 3Y 3A B A 2 1B 1A NC VCC 1Y NC 2A NC 2B FUNCTION TABLE (each gate) OUTPUT Y 14 SN54AS1032A . . . FK PACKAGE (TOP VIEW) The SN54AS1032A is characterized for operation over the full military temperature range of − 55°C to 125°C. The SN74AS1032A is characterized for operation from 0°C to 70°C. INPUTS 1 4B • • • NC − No internal connection logic symbol† 1A 1B 2A 2B 3A 3B 4A 4B 1 2 logic diagram (positive logic) ≥1 3 1A 1Y 1B 4 6 5 2A 2Y 2B 9 8 10 3A 3Y 3B 12 11 13 4A 4Y 4B 1 2 3 1Y 4 5 6 2Y 9 10 8 3Y 12 13 11 4Y † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the D, J, and N packages. Copyright  1995, Texas Instruments Incorporated   !"#$%! & '("")% $& ! *(+,'$%! -$%). "!-('%& '!!"# %! &*)''$%!& *)" %/) %)"#& ! )0$& &%"(#)%& &%$-$"- 1$""$%2. "!-('%! *"!')&&3 -!)& !% )')&&$",2 ',(-) %)&%3 ! $,, *$"$#)%)"&. • DALLAS, TEXAS 75265 • HOUSTON, TEXAS 77251−1443 POST OFFICE BOX 655303 POST OFFICE BOX 1443 1 

  

   


 SDAS072B − DECEMBER 1982 − REVISED JANUARY 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Operating free-air temperature range, TA: SN54AS1032A . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C SN74AS1032A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. recommended operating conditions‡ SN54AS1032A SN74AS1032A MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 UNIT VCC VIH Supply voltage VIL IOH Low-level input voltage 0.8 0.8 V High-level output current −40 −48 mA 48 mA 70 °C High-level input voltage 2 2 IOL Low-level output current TA Operating free-air temperature −55 ‡ These high sink- or source-current devices are not recommended for use above 40 MHz. V 40 125 V 0 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH SN54AS1032A MIN TYP§ MAX TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V to 5.5 V, II = −18 mA IOH = − 2 mA VCC = 4.5 V IOH = − 3 mA IOH = − 40 mA VOL VCC = 4.5 V II IIH VCC = 5.5 V, VCC = 5.5 V, IIL IO¶ VCC = 5.5 V, VCC = 5.5 V, ICCH ICCL VCC = 5.5 V, VCC = 5.5 V, SN74AS1032A MIN TYP§ MAX −1.2 VCC − 2 2.4 −1.2 VCC − 2 2.4 3.2 V 3.2 V 2 IOH = − 48 mA IOL = 40 mA UNIT 2 0.25 IOL = 48 mA VI = 7 V 0.5 0.35 VI = 2.7 V VI = 0.4 V VO = 2.25 V VI = 4.5 V −50 V 0.1 0.1 20 20 µA −0.5 −0.5 mA −200 mA 11.5 mA −200 7.7 0.5 11.5 −50 7.7 mA VI = 0 14.7 24 14.7 24 mA § All typical values are at VCC = 5 V, TA = 25°C. ¶ The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS. 2 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 

  

   


 SDAS072B − DECEMBER 1982 − REVISED JANUARY 1995 switching characteristics (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) VCC = 4.5 V to 5.5 V, CL = 50 pF, RL = 500 Ω, TA = MIN to MAX† SN54AS1032A tPLH tPHL A or B Y UNIT SN74AS1032A MIN MAX MIN MAX 1 7 1 6.3 1 7 1 6.3 ns † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 3 

  

   


 SDAS072B − DECEMBER 1982 − REVISED JANUARY 1995 PARAMETER MEASUREMENT INFORMATION SERIES 54ALS/74ALS AND 54AS/74AS DEVICES 7V RL = R1 = R2 VCC S1 RL R1 Test Point From Output Under Test CL (see Note A) From Output Under Test RL Test Point CL (see Note A) CL (see Note A) LOAD CIRCUIT FOR BI-STATE TOTEM-POLE OUTPUTS LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS 3.5 V Timing Input Test Point From Output Under Test LOAD CIRCUIT FOR 3-STATE OUTPUTS 3.5 V High-Level Pulse 1.3 V R2 1.3 V 1.3 V 0.3 V 0.3 V tsu Data Input tw th 3.5 V 1.3 V 3.5 V Low-Level Pulse 1.3 V 0.3 V 1.3 V 0.3 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATIONS 3.5 V Output Control (low-level enabling) 1.3 V 1.3 V 0.3 V tPZL Waveform 1 S1 Closed (see Note B) tPLZ 3.5 V Input tPHZ 1.3 V 0.3 V tPHL tPLH VOH In-Phase Output VOL 0.3 V 1.3 V 1.3 V VOL tPLH tPHL VOH 1.3 V 1.3 V [3.5 V 1.3 V tPZH Waveform 2 S1 Open (see Note B) 1.3 V VOH Out-of-Phase Output (see Note C) 0.3 V [0 V 1.3 V 1.3 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. When measuring propagation delay items of 3-state outputs, switch S1 is open. D. All input pulses have the following characteristics: PRR ≤ 1 MHz, tr = tf = 2 ns, duty cycle = 50%. E. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuits and Voltage Waveforms 4 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74AS1032AD ACTIVE SOIC D 14 50 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 AS1032A SN74AS1032AN ACTIVE PDIP N 14 25 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 SN74AS1032AN (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of