SN74AS573ADW


 

 

 

    
  
 
  
SDAS048D − DECEMBER 1989 − REVISED JANUARY 1995 OE 1D 2D 3D 4D 5D 6D 7D 8D GND description These octal D-type transparent latches feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q LE 2D 1D SN54ALS573C, SN54AS573A . . . FK PACKAGE (TOP VIEW) While the latch-enable (LE) input is high, outputs (Q) respond to the data (D) inputs. When LE is low, the outputs are latched to retain the data that was set up. 3D 4D 5D 6D 7D 4 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 2Q 3Q 4Q 5Q 6Q 8D GND LE 8Q 7Q A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus lines without interface or pullup components. 3 1Q • • • SN54ALS573C, SN54AS573A . . . J OR W PACKAGE SN74ALS573C, SN74AS573A . . . DW OR N PACKAGE (TOP VIEW) 3-State Buffer-Type Outputs Drive Bus Lines Directly Bus-Structured Pinout True Logic Outputs Package Options Include Plastic Small-Outline (DW) Packages, Ceramic Chip Carriers (FK), Standard Plastic (N) and Ceramic (J) 300-mil DIPs, and Ceramic Flat (W) Packages OE VCC • OE does not affect internal operation of the latches. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. The SN54ALS573C and SN54AS573A are characterized for operation over the full military temperature range of −55°C to 125°C. The SN74ALS573C and SN74AS573A are characterized for operation from 0°C to 70°C. FUNCTION TABLE (each latch) INPUTS OE LE D OUTPUT Q L H H H L H L L L L X Q0 H X X Z Copyright  1995, Texas Instruments Incorporated      ! "#$ !  %#&'" ($) (#"! "  !%$""! %$ *$ $!  $+! !#$! !(( ,-) (#" %"$!!. ($!  $"$!!'- "'#($ $!.  '' %$$!) • DALLAS, TEXAS 75265 • HOUSTON, TEXAS 77251−1443 POST OFFICE BOX 655303 POST OFFICE BOX 1443 1 

 

 

 

    
  
 
  
SDAS048D − DECEMBER 1989 − REVISED JANUARY 1995 logic symbol† OE LE 1D 2D 3D 4D 5D 6D 7D 8D 1 11 2 logic diagram (positive logic) EN OE C1 19 1D 3 18 4 17 5 16 6 15 7 14 8 13 9 12 LE 1 11 1Q C1 2Q 1D 3Q 2 19 1Q 1D 4Q 5Q 6Q 7Q To Seven Other Channels 8Q † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡ Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Operating free-air temperature range, TA: SN54ALS573C . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C SN74ALS573C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C ‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. recommended operating conditions SN54ALS573C SN74ALS573C MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 UNIT VCC VIH Supply voltage VIL IOH Low-level input voltage 0.7 0.8 V High-level output current −1 −2.6 mA IOL tw Low-level output current 12 24 mA Pulse duration, LE high 25 10 ns tsu th Setup time, data before LE↓ 10 10 ns 7 7 ns TA Operating free-air temperature 2 High-level input voltage 2 Hold time, data after LE↓ −55 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 2 125 0 V V 70 °C 

 

 

 

    
  
 
  
SDAS048D − DECEMBER 1989 − REVISED JANUARY 1995 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK SN54ALS573C TYP† MAX TEST CONDITIONS MIN VCC = 4.5 V, VCC = 4.5 V to 5.5 V, II = − 18 mA IOH = − 0.4 mA VCC = 4.5 V IOH = − 1 mA IOH = − 2.6 mA VOL VCC = 4.5 V IOL = 12 mA IOL = 24 mA IOZH IOZL VCC = 5.5 V, VCC = 5.5 V, VO = 2.7 V VO = 0.4 V II IIH VCC = 5.5 V, VCC = 5.5 V, VI = 7 V VI = 2.7 V IIL IO‡ VCC = 5.5 V, VCC = 5.5 V, VI = 0.4 V VO = 2.25 V VOH ICC VCC = 5.5 V SN74ALS573C TYP† MAX MIN −1.2 VCC − 2 2.4 −1.2 UNIT V VCC − 2 3.3 V 2.4 0.25 −20 3.2 0.4 0.25 0.4 0.35 0.5 V 20 20 µA −20 −20 µA 0.1 0.1 mA 20 20 µA −0.13 −0.1 mA −112 mA −112 −30 Outputs high 10 17 10 17 Outputs low 15 24 15 24 Outputs disabled 16 27 16 27 mA † All typical values are at VCC = 5 V, TA = 25°C. ‡ The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS. switching characteristics (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) VCC = 4.5 V to 5.5 V, CL = 50 pF, R1 = 500 Ω, R2 = 500 Ω, TA = MIN to MAX§ SN54ALS573C tPLH tPHL D Q tPLH tPHL LE Q tPZH tPZL OE Q tPHZ tPLZ OE Q UNIT SN74ALS573C MIN MAX MIN MAX 2 20 2 14 2 17 2 14 8 33 6 20 8 24 6 19 4 28 3 18 4 21 4 18 2 20 1 10 3 26 1 15 ns ns ns ns § For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 3 

 

 

 

    
  
 
  
SDAS048D − DECEMBER 1989 − REVISED JANUARY 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Operating free-air temperature range, TA: SN54AS573A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C SN74AS573A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. recommended operating conditions SN54AS573A SN74AS573A MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 UNIT VCC VIH Supply voltage VIL IOH Low-level input voltage 0.8 0.8 V High-level output current −12 −15 mA IOL tw* Low-level output current 48 mA tsu* th* High-level input voltage 2 2 V 32 Pulse duration, LE high V 5.5 4.5 ns Setup time, data before LE↓ 2 2 ns Hold time, data after LE↓ 3 3 ns TA Operating free-air temperature −55 125 0 70 * On products compliant to MIL-STD-883, Class B, this parameter is based on characterization data but is not production tested. °C electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK SN54AS573A TYP‡ MAX TEST CONDITIONS MIN VCC = 4.5 V, VCC = 4.5 V to 5.5 V, II = − 18 mA IOH = − 2 mA VCC = 4.5 V IOH = − 12 mA IOH = − 15 mA VOL VCC = 4.5 V IOL = 32 mA IOL = 48 mA IOZH IOZL VCC = 5.5 V, VCC = 5.5 V, VO = 2.7 V VO = 0.4 V II IIH VCC = 5.5 V, VCC = 5.5 V, VI = 7 V VI = 2.7 V IIL IO§ VCC = 5.5 V, VCC = 5.5 V, VI = 0.4 V VO = 2.25 V ICC VCC = 5.5 V VOH SN74AS573A TYP‡ MAX MIN −1.2 VCC − 2 2.4 −1.2 UNIT V VCC − 2 3.2 V 2.4 0.28 3.3 0.5 0.33 −30 0.5 V µA 50 50 −50 −50 µA 0.1 0.1 mA 20 20 µA −0.1 −0.5 mA −112 mA −112 −30 Outputs high 56 93 56 Outputs low 55 90 55 93 90 Outputs disabled 65 106 65 106 mA ‡ All typical values are at VCC = 5 V, TA = 25°C. § The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS. 4 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 

 

 

 

    
  
 
  
SDAS048D − DECEMBER 1989 − REVISED JANUARY 1995 switching characteristics (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL D Q tPLH tPHL LE Q tPZH tPZL OE Q tPHZ tPLZ OE Q VCC = 4.5 V to 5.5 V, CL = 50 pF, R1 = 500 Ω, R2 = 500 Ω, TA = MIN to MAX† SN54AS573A SN74AS573A MIN MAX MIN MAX 3 11 3 8 3 8 3 7 6 16.5 6 13 4 9 4 7.5 2 8 2 6.5 4 11 4 9.5 2 8 2 6.5 2 8 2 7 UNIT ns ns ns ns † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 5 

 

 

 

    
  
 
  
SDAS048D − DECEMBER 1989 − REVISED JANUARY 1995 PARAMETER MEASUREMENT INFORMATION SERIES 54ALS/74ALS AND 54AS/74AS DEVICES 7V RL = R1 = R2 VCC S1 RL R1 Test Point From Output Under Test CL (see Note A) From Output Under Test RL Test Point CL (see Note A) CL (see Note A) LOAD CIRCUIT FOR BI-STATE TOTEM-POLE OUTPUTS 3.5 V High-Level Pulse 1.3 V R2 LOAD CIRCUIT FOR 3-STATE OUTPUTS LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS 3.5 V Timing Input Test Point From Output Under Test 1.3 V 1.3 V 0.3 V 0.3 V tsu Data Input tw th 3.5 V 1.3 V 3.5 V Low-Level Pulse 1.3 V 0.3 V 1.3 V 0.3 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATIONS 3.5 V Output Control (low-level enabling) 1.3 V 1.3 V 0.3 V tPZL Waveform 1 S1 Closed (see Note B) tPLZ 3.5 V Input tPHZ 1.3 V 0.3 V tPHL tPLH VOH In-Phase Output VOL 0.3 V 1.3 V 1.3 V VOL tPLH tPHL VOH 1.3 V 1.3 V [3.5 V 1.3 V tPZH Waveform 2 S1 Open (see Note B) 1.3 V VOH Out-of-Phase Output (see Note C) 0.3 V [0 V 1.3 V 1.3 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. When measuring propagation delay items of 3-state outputs, switch S1 is open. D. All input pulses have the following characteristics: PRR ≤ 1 MHz, tr = tf = 2 ns, duty cycle = 50%. E. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuits and Voltage Waveforms 6 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 84012012A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 84012012A SNJ54ALS 573CFK 8401201RA ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 8401201RA SNJ54ALS573CJ Samples 8401201SA ACTIVE CFP W 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 8401201SA SNJ54ALS573CW Samples JM38510/38201B2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 JM38510/ 38201B2A Samples JM38510/38201BRA ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 JM38510/ 38201BRA Samples M38510/38201B2A ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 JM38510/ 38201B2A Samples M38510/38201BRA ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 JM38510/ 38201BRA Samples SN54ALS573CJ ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SN54ALS573CJ Samples SN54AS573AJ ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SN54AS573AJ Samples SN74ALS573CDBR ACTIVE SSOP DB 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 G573C Samples SN74ALS573CDW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS573C Samples SN74ALS573CDWR ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS573C Samples SN74ALS573CN ACTIVE PDIP N 20 20 RoHS & Non-Green NIPDAU N / A for Pkg Type 0 to 70 SN74ALS573CN Samples SN74ALS573CNE4 ACTIVE PDIP N 20 20 RoHS & Non-Green NIPDAU N / A for Pkg Type 0 to 70 SN74ALS573CN Samples SN74ALS573CNSR ACTIVE SO NS 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS573C Samples SN74ALS573CNSRE4 ACTIVE SO NS 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 ALS573C Samples SN74AS573ADW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 AS573A Samples Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 14-Oct-2022 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) SN74AS573AN ACTIVE PDIP N 20 20 RoHS & Non-Green NIPDAU N / A for Pkg Type 0 to 70 SN74AS573AN SNJ54ALS573CFK ACTIVE LCCC FK 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 84012012A SNJ54ALS 573CFK SNJ54ALS573CJ ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 8401201RA SNJ54ALS573CJ Samples SNJ54ALS573CW ACTIVE CFP W 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 8401201SA SNJ54ALS573CW Samples SNJ54AS573AJ ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SNJ54AS573AJ Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of