SN74CBT16861DLR

SN74CBT16861 20-BIT FET BUS SWITCH SCDS068C – JULY 1998 – REVISED OCTOBER 2000 D D D D DGG, DGV, OR DL PACKAGE (TOP VIEW) Member of Texas Instruments’ Widebus Family 5-Ω Switch Connection Between Two Ports TTL-Compatible Input Levels Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II NC 1A1 1A2 1A3 1A4 1A5 1A6 1A7 1A8 1A9 1A10 GND NC 2A1 2A2 2A3 2A4 2A5 2A6 2A7 2A8 2A9 2A10 GND description The SN74CBT16861 provides 20 bits of high-speed TTL-compatible bus switching. The low on-state resistance of the switch allows connections to be made with minimal propagation delay. The device is organized as one dual 10-bit switch with separate output-enable (OE) input. When OE is low, the switch is on, and port A is connected to port B. When OE is high, the switch is open, and the high-impedance state exists between the two ports. 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 VCC 1OE 1B1 1B2 1B3 1B4 1B5 1B6 1B7 1B8 1B9 1B10 VCC 2OE 2B1 2B2 2B3 2B4 2B5 2B6 2B7 2B8 2B9 2B10 NC – No internal connection ORDERING INFORMATION TA PACKAGE† ORDERABLE PART NUMBER Tube SN74CBT16861DL Tape and reel SN74CBT16861DLR Tape and reel SN74CBT16861DGGR SSOP – DL –40°C 40°C to 85°C TSSOP – DGG TOP-SIDE MARKING CBT16861 CBT16861 TVSOP – DGV Tape and reel SN74CBT16861DGVR CY861 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (each 10-bit bus switch) INPUT OE FUNCTION L A port = B port H Disconnect Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments. Copyright  2000, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74CBT16861 20-BIT FET BUS SWITCH SCDS068C – JULY 1998 – REVISED OCTOBER 2000 logic diagram (positive logic) 2 46 1A1 1B1 11 37 1A10 1OE 1B10 47 14 34 2A1 2B1 23 25 2B10 2A10 2OE 35 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Continuous channel current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 3) MIN MAX VCC VIH Supply voltage 4 5.5 High-level control input voltage 2 VIL TA Low-level control input voltage Operating free-air temperature –40 UNIT V V 0.8 V 85 °C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74CBT16861 20-BIT FET BUS SWITCH SCDS068C – JULY 1998 – REVISED OCTOBER 2000 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK II ICC ∆ICC‡ Control inputs Ci Control inputs Cio(OFF) TEST CONDITIONS VCC = 4.5 V, VCC = 0, II = –18 mA VI = 5.5 V VCC = 5.5 V, VCC = 5.5 V, VI = 5.5 V or GND IO = 0, VCC = 5.5 V, VI = 3 V or 0 One input at 3.4 V, VO = 3 V or 0, VCC = 4 V, TYP at VCC = 4 V OE = VCC ron§ VCC = 4.5 V MIN TYP† MAX UNIT –1.2 V 10 ±1 VI = VCC or GND Other inputs at VCC or GND µA 3 µA 2.5 mA 3 pF 5.5 pF VI = 2.4 V, II = 15 mA 14 22 VI = 0 II = 64 mA II = 30 mA 5 7 5 7 Ω VI = 2.4 V, II = 15 mA 10 15 † All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C. ‡ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. § Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by the lowest voltage of the two (A or B) terminals. switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tpd¶ A or B B or A ten OE A or B PARAMETER VCC = 4 V VCC = 5 V ± 0.5 V MIN MIN MAX 0.35 2.7 6.3 1.7 UNIT MAX 0.25 ns 6.5 ns tdis A or B 1.5 8 1.8 7.1 ns OE ¶ The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74CBT16861 20-BIT FET BUS SWITCH SCDS068C – JULY 1998 – REVISED OCTOBER 2000 PARAMETER MEASUREMENT INFORMATION 7V 500 Ω From Output Under Test S1 Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 7V Open 3V Output Control LOAD CIRCUIT 1.5 V 1.5 V 0V tPLZ tPZL 3V Input 1.5 V 1.5 V 0V tPLH 1.5 V 3.5 V 1.5 V 1.5 V VOL Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOL + 0.3 V VOL tPHZ tPZH tPHL VOH Output Output Waveform 1 S1 at 7 V (see Note B) 1.5 V VOH VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74CBT16861DGGR ACTIVE TSSOP DGG 48 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 CBT16861 SN74CBT16861DGVR ACTIVE TVSOP DGV 48 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 CY861 SN74CBT16861DLR ACTIVE SSOP DL 48 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 CBT16861 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of