SN74HC158D


        


SCLS296D − JANUARY 1996 − REVISED OCTOBER 2003 D Wide Operating Voltage Range of 2 V to 6 V D Outputs Can Drive Up To 15 LSTTL Loads D Low Power Consumption, 80-µA Max ICC D Typical tpd = 11 ns D ±6-mA Output Drive at 5 V D Low Input Current of 1 µA Max SN54HC158 . . . FK PACKAGE (TOP VIEW) 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC G 4A 4B 4Y 3A 3B 3Y 1B 1Y NC 2A 2B 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4A 4B NC 4Y 3A 2Y GND NC 3Y 3B A/B 1A 1B 1Y 2A 2B 2Y GND 1A A/B NC VCC G SN54HC158 . . . J OR W PACKAGE SN74HC158 . . . D, N, NS, OR PW PACKAGE (TOP VIEW) NC − No internal connection description/ordering information These data selectors/multiplexers contain inverters and drivers that supply full data selection to the four output gates. A separate strobe (G) input is provided. A 4-bit word is selected from one of two sources and is routed to the four outputs. The ’HC158 devices’ outputs provide inverted data. ORDERING INFORMATION PACKAGE† TA PDIP − N SN74HC158N Tube of 40 SN74HC158D Reel of 2500 SN74HC158DR Reel of 250 SN74HC158DT Reel of 2000 SN74HC158NSR Tube of 90 SN74HC158PW Reel of 2000 SN74HC158PWR Reel of 250 SN74HC158PWT CDIP − J Tube of 25 SNJ54HC158J SNJ54HC158J CFP − W Tube of 150 SNJ54HC158W SNJ54HC158W LCCC − FK Tube of 55 SNJ54HC158FK SOP − NS TSSOP − PW −55°C −55 C to 125 125°C C TOP-SIDE MARKING Tube of 25 SOIC − D −40°C to 85°C ORDERABLE PART NUMBER SN74HC158N HC158 HC158 HC158 SNJ54HC158FK † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2003, Texas Instruments Incorporated 


   !"#$%&' #"'('    ')"*%("' #$**&' ( ") +$,-#("' !(&. *"!$# #"')"*% " +&#)#("' +&* & &*% ") &/( '*$%&' ('!(*! 0(**('1. *"!$#"' +*"#&'2 !"& '" '&#&(*-1 '#-$!& &'2 ") (-+(*(%&&*. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 

        


SCLS296D − JANUARY 1996 − REVISED OCTOBER 2003 FUNCTION TABLE INPUTS OUTPUT Y DATA G SELECT A/B A B H X X X H L L L X H L L H X L L H X L H L H X H L logic diagram (positive logic) 1A 2 4 1B 2A 3 5 7 2B 3A 6 4A 10 G A/B 13 15 1 Pin numbers shown are for the D, J, N, NS, PW, and W packages. 2 3Y 14 12 4B 2Y 11 9 3B 1Y POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 4Y 

        


SCLS296D − JANUARY 1996 − REVISED OCTOBER 2003 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±35 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±70 mA Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 3) SN54HC158 VCC VIH Supply voltage High-level input voltage VCC = 2 V VCC = 4.5 V VCC = 6 V VCC = 2 V VIL VI VO ∆t/∆v Low-level input voltage MIN NOM MAX 2 5 6 MIN NOM MAX 2 5 6 1.5 1.5 3.15 3.15 4.2 4.2 VCC = 4.5 V VCC = 6 V Input voltage 0 Output voltage 0 Input transition rise/fall time SN74HC158 VCC = 2 V VCC = 4.5 V VCC = 6 V 0.5 1.35 1.35 1.8 1.8 0 0 V V 0.5 VCC VCC UNIT VCC VCC 1000 1000 500 500 400 400 V V V ns TA Operating free-air temperature −55 125 −40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004.  3 ')"*%("' #"'#&*' +*"!$# ' & )"*%(4& "* !&2' +(& ") !&4&-"+%&'. (*(#&*# !(( ('! "&* +&#)#("' (*& !&2' 2"(-. &/( '*$%&' *&&*4& & *2 " #('2& "* !#"''$& && +*"!$# 0"$ '"#&. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 

        


SCLS296D − JANUARY 1996 − REVISED OCTOBER 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = −20 µA VOH VI = VIH or VIL IOH = −6 mA IOH = −7.8 mA IOL = 20 µA VOL VI = VIH or VIL IOL = 6 mA IOL = 7.8 mA II ICC VI = VCC or 0 VI = VCC or 0, IO = 0 VCC MIN TA = 25°C TYP MAX MIN MAX SN74HC158 MIN 2V 1.9 1.998 1.9 1.9 4.5 V 4.4 4.499 4.4 4.4 6V 5.9 5.999 5.9 5.9 4.5 V 3.98 4.3 3.7 3.84 6V 5.48 5.8 5.2 MAX UNIT V 5.34 2V 0.002 0.1 0.1 0.1 4.5 V 0.001 0.1 0.1 0.1 6V 0.001 0.1 0.1 0.1 4.5 V 0.17 0.26 0.4 0.33 6V 0.15 0.26 0.4 0.33 6V ±0.1 ±100 ±1000 ±1000 nA 8 160 80 µA 3 10 10 10 pF 6V Ci SN54HC158 2 V to 6 V V switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) PARAMETER tpd TA = 25°C TYP MAX SN74HC158 TO (OUTPUT) VCC 2V 63 125 190 160 A or B Y 4.5 V 13 25 38 32 6V 11 21 32 27 A/B G tt Y Y Y MIN MIN MAX MIN MAX 2V 67 125 190 160 4.5 V 18 25 38 31 6V 14 21 32 27 2V 59 115 170 145 4.5 V 16 23 34 29 6V 13 20 29 25 2V 28 60 90 75 4.5 V 8 12 18 15 6V 6 10 15 13  3 ')"*%("' #"'#&*' +*"!$# ' & )"*%(4& "* !&2' +(& ") !&4&-"+%&'. (*(#&*# !(( ('! "&* +&#)#("' (*& !&2' 2"(-. &/( '*$%&' *&&*4& & *2 " #('2& "* !#"''$& && +*"!$# 0"$ '"#&. 4 SN54HC158 FROM (INPUT) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT ns ns 

        


SCLS296D − JANUARY 1996 − REVISED OCTOBER 2003 switching characteristics over recommended operating free-air temperature range, CL = 150 pF (unless otherwise noted) (see Figure 1) PARAMETER tpd TA = 25°C TYP MAX SN54HC158 SN74HC158 FROM (INPUT) TO (OUTPUT) VCC 2V 81 190 290 235 A or B Y 4.5 V 23 38 58 47 6V 18 33 49 41 A/B Y G Y tt Y MIN MIN MAX MIN MAX 2V 81 210 320 260 4.5 V 23 42 64 52 6V 18 36 54 45 2V 91 190 290 235 4.5 V 24 38 58 47 6V 18 33 49 41 2V 45 210 315 265 4.5 V 17 42 63 53 6V 13 36 53 45 UNIT ns ns operating characteristics, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance No load TYP UNIT 40 pF PARAMETER MEASUREMENT INFORMATION From Output Under Test Test Point Input VCC 50% 50% 0V CL (see Note A) tPLH In-Phase Output LOAD CIRCUIT 50% 10% tPHL 90% 90% tr Input 50% 10% 90% 90% tr VCC 50% 10% 0 V tPHL Out-of-Phase Output 90% tf VOH 50% 10% VOL tf tPLH 50% 10% tf 50% 10% 90% VOH VOL tr VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT TRANSITION TIMES VOLTAGE WAVEFORM INPUT RISE AND FALL TIMES NOTES: A. CL includes probe and test-fixture capacitance. B. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns. C. The outputs are measured one at a time with one input transition per measurement. D. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms  3 ')"*%("' #"'#&*' +*"!$# ' & )"*%(4& "* !&2' +(& ") !&4&-"+%&'. (*(#&*# !(( ('! "&* +&#)#("' (*& !&2' 2"(-. &/( '*$%&' *&&*4& & *2 " #('2& "* !#"''$& && +*"!$# 0"$ '"#&. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) SN74HC158D ACTIVE SOIC D 16 40 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HC158 Samples SN74HC158DR ACTIVE SOIC D 16 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HC158 Samples SN74HC158DT ACTIVE SOIC D 16 250 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HC158 Samples SN74HC158N ACTIVE PDIP N 16 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74HC158N Samples SN74HC158NE4 ACTIVE PDIP N 16 25 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74HC158N Samples SN74HC158NSR ACTIVE SO NS 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HC158 Samples SN74HC158PW ACTIVE TSSOP PW 16 90 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HC158 Samples SN74HC158PWR ACTIVE TSSOP PW 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HC158 Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of