SN74HC165N


    
 

SCLS116E − DECEMBER 1982 − REVISED SEPTEMBER 2003 D D D D D Wide Operating Voltage Range of 2 V to 6 V Outputs Can Drive Up To 10 LSTTL Loads Low Power Consumption, 80-µA Max ICC Typical tpd = 13 ns ±4-mA Output Drive at 5 V D D D D D Low Input Current of 1 µA Max Complementary Outputs Direct Overriding Load (Data) Inputs Gated Clock Inputs Parallel-to-Serial Data Conversion SN54HC165 . . . FK PACKAGE (TOP VIEW) 1 16 2 15 3 14 4 13 5 12 6 7 8 11 10 9 VCC CLK INH D C B A SER QH E F NC G H 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 D C NC B A QH GND NC QH SER SH/LD CLK E F G H QH GND CLK SH/LD NC VCC CLK INH SN54HC165 . . . J OR W PACKAGE SN74HC165 . . . D, DB, N, NS, OR PW PACKAGE (TOP VIEW) NC − No internal connection description/ordering information The ’HC165 devices are 8-bit parallel-load shift registers that, when clocked, shift the data toward a serial (QH) output. Parallel-in access to each stage is provided by eight individual direct data (A−H) inputs that are enabled by a low level at the shift/load (SH/LD) input. The ’HC165 devices also feature a clock-inhibit (CLK INH) function and a complementary serial (QH) output. ORDERING INFORMATION PACKAGE† TA PDIP − N SOIC − D −40°C 85°C −40 C to 85 C Tube of 25 SN74HC165N Tube of 40 SN74HC165D Reel of 2500 SN74HC165DR TOP-SIDE MARKING SN74HC165N HC165 Reel of 250 SN74HC165DT SOP − NS Reel of 2000 SN74HC165NSR HC165 SSOP − DB Reel of 2000 SN74HC165DBR HC165 Tube of 90 SN74HC165PW Reel of 2000 SN74HC165PWR Reel of 250 SN74HC165PWT CDIP − J Tube of 25 SNJ54HC165J SNJ54HC165J CFP − W Tube of 150 SNJ54HC165W SNJ54HC165W LCCC − FK Tube of 55 SNJ54HC165FK TSSOP − PW −55°C −55 C to 125 125°C C ORDERABLE PART NUMBER HC165 SNJ54HC165FK † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2003, Texas Instruments Incorporated   !" # $%&" !#  '%()$!" *!"&+ *%$"# $ " #'&$$!"# '& ",& "&#  &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0  !)) '!!&"&#+  '*%$"# $')!" " 122 !)) '!!&"&# !& "&#"&* %)&## ",&.#& "&*+  !)) ",& '*%$"# '*%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0  !)) '!!&"&#+ POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 

    
 

SCLS116E − DECEMBER 1982 − REVISED SEPTEMBER 2003 description/ordering information (continued) Clocking is accomplished by a low-to-high transition of the clock (CLK) input while SH/LD is held high and CLK INH is held low. The functions of CLK and CLK INH are interchangeable. Since a low CLK and a low-to-high transition of CLK INH also accomplish clocking, CLK INH should be changed to the high level only while CLK is high. Parallel loading is inhibited when SH/LD is held high. While SH/LD is low, the parallel inputs to the register are enabled independently of the levels of the CLK, CLK INH, or serial (SER) inputs. FUNCTION TABLE INPUTS FUNCTION SH/LD CLK CLK INH L X X H H X No change H X H L ↑ No change Shift† H Parallel load L Shift† † Shift = content of each internal register shifts toward serial output QH. Data at SER is shifted into the first register. ↑ H logic diagram (positive logic) A SH/LD CLK INH CLK SER 1 B 11 C 12 D 13 E 14 F 3 G 4 H 5 6 9 15 10 S C1 1D R S C1 1D R S C1 1D R S C1 1D R S C1 1D R S C1 1D R S C1 1D R S C1 1D R 7 Pin numbers shown are for the D, DB, J, N, NS, PW, and W packages. 2 QH 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 QH 

    
 

SCLS116E − DECEMBER 1982 − REVISED SEPTEMBER 2003 typical shift, load, and inhibit sequence CLK CLK INH SER L SH/LD Data Inputs A H B L C H D L E H F L G H H H QH H H L H L H L H QH L L H L H L H L Inhibit Serial Shift Load POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 

    
 

SCLS116E − DECEMBER 1982 − REVISED SEPTEMBER 2003 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 3) SN54HC165 VCC VIH Supply voltage High-level input voltage VCC = 2 V VCC = 4.5 V VCC = 6 V VCC = 2 V VIL VI VO ∆t/∆v‡ Low-level input voltage MIN NOM MAX 2 5 6 MIN NOM MAX 2 5 6 1.5 1.5 3.15 3.15 4.2 4.2 VCC = 4.5 V VCC = 6 V Input voltage 0 Output voltage 0 Input transition rise/fall time SN74HC165 VCC = 2 V VCC = 4.5 V VCC = 6 V 0.5 1.35 1.35 1.8 1.8 0 0 V V 0.5 VCC VCC UNIT VCC VCC 1000 1000 500 500 400 400 V V V ns TA Operating free-air temperature −55 125 −40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. ‡ If this device is used in the threshold region (from VILmax = 0.5 V to VIHmin = 1.5 V), there is a potential to go into the wrong state from induced grounding, causing double clocking. Operating with the inputs at tt = 1000 ns and VCC = 2 V does not damage the device; however, functionally, the CLK inputs are not ensured while in the shift, count, or toggle operating modes. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 

    
 

SCLS116E − DECEMBER 1982 − REVISED SEPTEMBER 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = −20 µA VOH VI = VIH or VIL IOH = −4 mA IOH = −5.2 mA IOL = 20 µA VOL VI = VIH or VIL IOL = 4 mA IOL = 5.2 mA II ICC Ci VI = VCC or 0 VI = VCC or 0, IO = 0 VCC MIN TA = 25°C TYP MAX SN54HC165 MIN MAX SN74HC165 MIN 2V 1.9 1.998 1.9 1.9 4.5 V 4.4 4.499 4.4 4.4 6V 5.9 5.999 5.9 5.9 4.5 V 3.98 4.3 3.7 3.84 6V 5.48 5.8 5.2 MAX UNIT V 5.34 2V 0.002 0.1 0.1 0.1 4.5 V 0.001 0.1 0.1 0.1 6V 0.001 0.1 0.1 0.1 4.5 V 0.17 0.26 0.4 0.33 6V 0.15 0.26 0.4 0.33 6V ±0.1 ±100 ±1000 ±1000 nA 8 160 80 µA 3 10 10 10 pF 6V 2 V to 6 V POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 V 5 

    
 

SCLS116E − DECEMBER 1982 − REVISED SEPTEMBER 2003 timing requirements over recommended operating free-air temperature range (unless otherwise noted) VCC fclock Clock frequency SH/LD low tw Pulse duration CLK high or low SH/LD high before CLK↑ SER before CLK↑ tsu Setup time CLK INH low before CLK↑ CLK INH high before CLK↑ Data before SH/LD↓ SER data after CLK↑ th Hold time PAR data after SH/LD↓ 6 POST OFFICE BOX 655303 TA = 25°C MIN MAX SN54HC165 MIN MAX SN74HC165 MIN MAX 2V 6 4.2 5 4.5 V 31 21 25 6V 36 25 29 2V 80 120 100 4.5 V 16 24 20 6V 14 20 17 2V 80 120 100 4.5 V 16 24 20 6V 14 20 17 2V 80 120 100 4.5 V 16 24 20 6V 14 20 17 2V 40 60 50 4.5 V 8 12 10 6V 7 10 9 2V 100 150 125 4.5 V 20 30 25 6V 17 25 21 2V 40 60 50 4.5 V 8 12 10 6V 7 10 9 2V 100 150 125 4.5 V 20 30 25 6V 17 26 21 2V 5 5 5 4.5 V 5 5 5 6V 5 5 5 2V 5 5 5 4.5 V 5 5 5 6V 5 5 5 • DALLAS, TEXAS 75265 UNIT MHz ns ns ns 

    
 

SCLS116E − DECEMBER 1982 − REVISED SEPTEMBER 2003 switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) fmax SH/LD tpd CLK H tt QH or QH QH or QH QH or QH Any VCC MIN TA = 25°C TYP MAX SN54HC165 MIN MAX SN74HC165 MIN 2V 6 13 4.2 5 4.5 V 31 50 21 25 6V 36 62 25 29 MAX UNIT MHz 2V 80 150 225 190 4.5 V 20 30 45 38 6V 16 26 38 32 2V 75 150 225 190 4.5 V 15 30 45 38 6V 13 26 38 32 2V 75 150 225 190 4.5 V 15 30 45 38 6V 13 26 38 32 2V 38 75 110 95 4.5 V 8 15 22 19 6V 6 13 19 16 ns ns operating characteristics, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance No load POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TYP 75 UNIT pF 7 

    
 

SCLS116E − DECEMBER 1982 − REVISED SEPTEMBER 2003 PARAMETER MEASUREMENT INFORMATION From Output Under Test VCC High-Level Pulse Test Point 50% 50% 0V tw CL = 50 pF (see Note A) VCC Low-Level Pulse 50% 50% 0V LOAD CIRCUIT VOLTAGE WAVEFORMS PULSE DURATIONS Input VCC 50% 50% 0V tPLH Reference Input VCC 50% In-Phase Output 0V tsu Data Input 50% 10% 90% tr tPHL VCC 50% 10% 0 V 90% 90% tr th 90% 50% 10% tPHL Out-of-Phase Output 90% VOLTAGE WAVEFORMS SETUP AND HOLD AND INPUT RISE AND FALL TIMES tPLH 50% 10% tf tf VOH 50% 10% VOL tf 50% 10% 90% VOH VOL tr VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT TRANSITION TIMES NOTES: A. CL includes probe and test-fixture capacitance. B. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns. C. For clock inputs, fmax is measured when the input duty cycle is 50%. D. The outputs are measured one at a time with one input transition per measurement. E. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 26-Sep-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) 84095012A ACTIVE LCCC FK 20 1 TBD Call TI Level-NC-NC-NC 8409501EA ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC 8409501FA ACTIVE CFP W 16 1 TBD Call TI Level-NC-NC-NC SN54HC165J ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC SN74HC165D ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165DBR ACTIVE SSOP DB 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165DBRE4 ACTIVE SSOP DB 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165DE4 ACTIVE SOIC D 16 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165DR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165DRE4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165DT ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165DTE4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165N ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC TBD Call TI 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC 40 SN74HC165N3 OBSOLETE PDIP N 16 SN74HC165NE4 ACTIVE PDIP N 16 SN74HC165NSR ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165NSRE4 ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165PW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165PWLE OBSOLETE TSSOP PW 16 SN74HC165PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165PWT ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74HC165PWTE4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNJ54HC165FK ACTIVE LCCC FK 20 1 TBD Call TI Level-NC-NC-NC SNJ54HC165J ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC SNJ54HC165W ACTIVE CFP W 16 1 TBD Call TI Level-NC-NC-NC TBD (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. Addendum-Page 1 Call TI Call TI Call TI PACKAGE OPTION ADDENDUM www.ti.com 26-Sep-2005 LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA MLCC006B – OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright  2005, Texas Instruments Incorporated