SN74HCT540DWRE4

SN54HCT540, SN74HCT540 OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS SCLS008C – MARCH 1984 – REVISED MARCH 2003 D D D D D D D D Operating Voltage Range of 4.5 V to 5.5 V Low Power Consumption, 80-µA Max ICC Typical tpd = 12 ns ±6-mA Output Drive at 5 V Low Input Current of 1 µA Max Inputs Are TTL-Voltage Compatible High-Current 3-State Outputs Interface Directly With System Bus or Can Drive Up To 15 LSTTL Loads Data Flow-Through Pinout (All Inputs on Opposite Side From Outputs) SN54HCT540 . . . J PACKAGE SN74HCT540 . . . DW OR N PACKAGE (TOP VIEW) OE1 A1 A2 A3 A4 A5 A6 A7 A8 GND description/ordering information 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC OE2 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 These octal buffers and line drivers are designed to have the performance of the ’HCT240 devices and a pinout with inputs and outputs on opposite sides of the package. This arrangement greatly facilitates printed circuit board layout. The 3-state control gate is a 2-input NOR. If either output-enable (OE1 or OE2) input is high, all eight outputs are in the high-impedance state. The ’HCT540 devices provide inverted data at the outputs. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION PDIP – N –40°C to 85°C ORDERABLE PART NUMBER PACKAGE† TA SOIC – DW Tube SN74HCT540N Tube SN74HCT540DW Tape and reel SN74HCT540DWR TOP-SIDE MARKING SN74HCT540N HCT540 –55°C to 125°C CDIP – J Tube SNJ54HCT540J SNJ54HCT540J † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (each buffer/driver) INPUTS OE1 OE2 A OUTPUT Y L L L H L L H L H X X Z X H X Z Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2003, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54HCT540, SN74HCT540 OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS SCLS008C – MARCH 1984 – REVISED MARCH 2003 logic diagram (positive logic) OE1 OE2 A1 1 19 2 18 Y1 To Seven Other Channels absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±35 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±70 mA Package thermal impedance, θJA (see Note 2): DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 3) SN54HCT540 NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 0 VO tt Output voltage 0 High-level input voltage VCC = 4.5 V to 5.5 V VCC = 4.5 V to 5.5 V SN74HCT540 MIN 2 2 0.8 Input transition (rise and fall) time VCC VCC 500 0 0 UNIT V V 0.8 V VCC VCC V 500 ns V TA Operating free-air temperature –55 125 –40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54HCT540, SN74HCT540 OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS SCLS008C – MARCH 1984 – REVISED MARCH 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC VOH VI = VIH or VIL IOH = –20 µA IOH = –6 mA 45V 4.5 VOL VI = VIH or VIL IOL = 20 µA IOL = 6 mA 45V 4.5 II IOZ VI = VCC or 0 VO = VCC or 0, ICC VI = VCC or 0, One input at 0.5 V or 2.4 V, Other inputs at 0 or VCC ∆ICC† VI = VIH or VIL IO = 0 TA = 25°C TYP MAX SN54HCT540 MIN MAX SN74HCT540 MIN 4.4 4.499 4.4 4.4 3.98 4.3 3.7 3.84 MAX UNIT V 0.001 0.1 0.1 0.1 0.17 0.26 0.4 0.33 5.5 V ±0.1 ±100 ±1000 ±1000 nA 5.5 V ±0.01 ±0.5 ±10 ±5 µA 8 160 80 µA 1.4 2.4 3 2.9 mA 3 10 10 10 pF 5.5 V 5.5 V 4.5 V to 5.5 V Ci MIN V † This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC. switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tpd d A Y ten OE Y tdis di OE Y tt Y VCC TA = 25°C MIN TYP MAX SN54HCT540 MIN MAX SN74HCT540 MIN MAX 4.5 V 13 20 30 25 5.5 V 12 18 27 23 4.5 V 20 30 45 38 5.5 V 18 27 41 34 4.5 V 19 30 45 38 5.5 V 18 27 41 34 4.5 V 8 12 18 15 5.5 V 7 11 16 14 UNIT ns ns ns ns switching characteristics over recommended operating free-air temperature range, CL = 150 pF (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tpd d A Y ten OE Y tt Y VCC TA = 25°C MIN TYP MAX SN54HCT540 MIN MAX SN74HCT540 MIN MAX 4.5 V 20 30 45 38 5.5 V 19 27 41 34 4.5 V 26 40 60 50 5.5 V 25 36 54 45 4.5 V 17 42 63 53 5.5 V 14 38 57 48 UNIT ns ns ns operating characteristics, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance per buffer/driver POST OFFICE BOX 655303 No load • DALLAS, TEXAS 75265 TYP 35 UNIT pF 3 SN54HCT540, SN74HCT540 OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS SCLS008C – MARCH 1984 – REVISED MARCH 2003 PARAMETER MEASUREMENT INFORMATION VCC From Output Under Test CL (see Note A) PARAMETER S1 Test Point tPZH ten RL S2 1 kΩ tPZL tPHZ tdis S2 50 pF or 150 pF Open Closed Closed Open 1 kΩ –– LOAD CIRCUIT 2.7 V S1 50 pF tPLZ tpd or tt Input 1.3 V 0.3 V CL RL 2.7 V 50 pF or 150 pF Open Closed Closed Open Open Open 3V 1.3 V 0.3 V 0 V tr tf VOLTAGE WAVEFORM INPUT RISE AND FALL TIMES Output Control (Low-Level Enabling) 3V Input 1.3 V 1.3 V 0V tPLH In-Phase Output 1.3 V 10% tPHL 90% 90% tr tPHL Out-ofPhase Output 90% VOH 1.3 V 10% V OL tf tPLH 1.3 V 10% 1.3 V 10% tf 3V 1.3 V 1.3 V 0V tPZL Output Waveform 1 (See Note B) tPLZ ≈VCC 1.3 V 10% tPZH 90% VOH VOL tr VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT RISE AND FALL TIMES Output Waveform 2 (See Note B) VOL tPHZ 1.3 V 90% VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES FOR 3-STATE OUTPUTS NOTES: A. CL includes probe and test-fixture capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns. D. The outputs are measured one at a time with one input transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 13-Aug-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) JM38510/65760BRA ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 JM38510/ 65760BRA M38510/65760BRA ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 JM38510/ 65760BRA SN54HCT540J ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SN54HCT540J SN74HCT540DW ACTIVE SOIC DW 20 25 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCT540 SN74HCT540DWR ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCT540 SN74HCT540DWRG4 ACTIVE SOIC DW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 HCT540 SN74HCT540N ACTIVE PDIP N 20 20 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 SN74HCT540N SNJ54HCT540J ACTIVE CDIP J 20 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 SNJ54HCT540J (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of