SN74LV125AT
QUADRUPLE BUS BUFFER GATE
WITH 3-STATE OUTPUTS
www.ti.com
SCES629A – MAY 2005 – REVISED AUGUST 2005
FEATURES
•
•
•
•
•
•
Inputs Are TTL-Voltage Compatible
4.5-V to 5.5-V VCC Operation
Typical tpd of 3.8 ns at 5 V
Typical VOLP (Output Ground Bounce)
2.3 V at VCC = 5 V, TA = 25°C
Support Mixed-Mode Voltage Operation on All
Ports
•
•
•
Ioff Supports Partial-Power-Down Mode
Operation
Latch-Up Performance Exceeds 250 mA Per
JESD 17
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
XXXX
XXXX
13
3
12
4
11
5
10
6
9
7
8
VCC
4OE
4A
4Y
3OE
3A
3Y
1A
1Y
2OE
2A
2Y
VCC
14
2
1
14
2
13 4OE
3
12 4A
4
11 4Y
5
6
10 3OE
9 3A
7
8
3Y
1
GND
1OE
1A
1Y
2OE
2A
2Y
GND
1OE
RGY PACKAGE
(TOP VIEW)
D, DB, NS, OR PW PACKAGE
(TOP VIEW)
DESCRIPTION/ORDERING INFORMATION
The SN74LV125AT is a quadruple bus buffer gate. This device features independent line drivers with 3-state
outputs. Each output is disabled when the associated output-enable (OE) input is high.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
ORDERING INFORMATION
PACKAGE (1)
TA
QFN – RGY
SOIC – D
SOP – NS
–40°C to 85°C
SSOP – DB
TSSOP – PW
(1)
ORDERABLE PART NUMBER
Reel of 1000
SN74LV125ATRGYR
Tube of 50
SN74LV125ATD
Reel of 2500
SN74LV125ATDR
Tube of 50
SN74LV125ATNS
Reel of 2000
SN74LV125ATNSR
Tube of 80
SN74LV125ATDB
Reel of 2000
SN74LV125ATDBR
Tube of 90
SN74LV125ATPW
Reel of 2000
SN74LV125ATPWR
Reel of 250
SN74LV125ATPWT
TOP-SIDE MARKING
VV125
LV125AT
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005, Texas Instruments Incorporated
SN74LV125AT
QUADRUPLE BUS BUFFER GATE
WITH 3-STATE OUTPUTS
www.ti.com
SCES629A – MAY 2005 – REVISED AUGUST 2005
FUNCTION TABLE
(EACH BUFFER)
INPUTS
OE
A
OUTPUT
Y
L
H
H
L
L
L
H
X
Z
LOGIC DIAGRAM (POSITIVE LOGIC)
1OE
1A
1
2
3OE
3
1Y
3A
8
9
3Y
13
4
4OE
2OE
2A
10
5
6
2Y
4A
11
12
4Y
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
VCC
Supply voltage range
–0.5
7
V
VI
Input voltage range (2)
–0.5
7
V
VO
Voltage range applied to any output in the high-impedance or power-off state (2)
–0.5
7
V
VO
Output voltage range (2) (3)
–0.5
VCC + 0.5
V
IIK
Input clamp current
VI < 0
–20
mA
IOK
Output clamp current
VO < 0 or VO > VCC
±50
mA
IO
Continuous output current
VO = 0 to VCC
±35
mA
±70
mA
Continuous current through VCC or GND
θJA
Package thermal impedance
D package (4)
86
DB package (4)
96
package (4)
76
PW package (4)
113
NS
RGY package (5)
Tstg
(1)
(2)
(3)
(4)
(5)
2
Storage temperature range
°C/W
47
–65
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
This value is limited to 5.5 V maximum.
The package thermal impedance is calculated in accordance with JESD 51-7.
The package thermal impedance is calculated in accordance with JESD 51-5.
SN74LV125AT
QUADRUPLE BUS BUFFER GATE
WITH 3-STATE OUTPUTS
www.ti.com
SCES629A – MAY 2005 – REVISED AUGUST 2005
Recommended Operating Conditions
(1)
VCC
Supply voltage
VIH
High-level input voltage
VCC = 4.5 V to 5.5 V
VIL
Low-level input voltage
VCC = 4.5 V to 5.5 V
VI
Input voltage
MIN
MAX
4.5
5.5
UNIT
V
2
V
0.8
V
V
0
5.5
High or low state
0
VCC
3-state
0
5.5
VO
Output voltage
IOH
High-level output current
VCC = 4.5 V to 5.5 V
–16
IOL
Low-level output current
VCC = 4.5 V to 5.5 V
16
mA
∆t/∆v
Input transition rise or fall rate
VCC = 4.5 V to 5.5 V
20
ns/V
TA
Operating free-air temperature
125
°C
(1)
–40
V
mA
All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
VOH
VOL
VCC
TA = –40°C
to 85°C
TA = 25°C
MIN
TYP
4.5
IOH = –50 µA
4.5 V
4.4
IOH = –16 mA
4.5 V
3.8
IOL = 50 µA
4.5 V
IOL = 16 mA
4.5 V
MAX
0
MIN
TA = –40°C
to 125°C
MAX
MIN
4.4
4.4
3.8
3.8
UNIT
MAX
V
0.1
0.1
0.1
0.55
0.55
0.55
V
II
VI = 5.5 V or GND
0 to 5.5 V
±0.1
±1
±1
µA
IOZ
VO = VCC or GND
5.5 V
±0.25
±2.5
±2.5
µA
ICC
VI = VCC or GND, IO = 0
5.5 V
2
20
20
µA
One input at 3.4 V,
Other inputs at VCC or GND
5.5 V
1.35
1.5
1.5
mA
0
0.5
5
5
µA
∆ICC
(1)
TEST CONDITIONS
(1)
Ioff
VI or VO = 0 to 5.5 V
Ci
VI = VCC or GND
2
pF
This is the increase in supply current for each input at one of the specified TTL voltage levels, rather than 0 V or VCC.
Switching Characteristics
over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1)
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE
tpd
A
Y
ten
OE
Y
tdis
OE
tpd
ten
tdis
OE
PARAMETER
tsk(o)
TA = –40°C
to 85°C
TA = 25°C
TA = –40°C
to 125°C
UNIT
MIN
TYP
MAX
MIN
MAX
MIN
MAX
CL = 15 pF
1.9
3.8
5.5
1
6.5
1
8.5
ns
CL = 15 pF
2
3.6
5.1
1
6
1
7.5
ns
Y
CL = 15 pF
1.5
3.2
6.8
1
8
1
10
ns
A
Y
CL = 50 pF
2.9
5.3
7.5
1
8.5
1
10.5
ns
OE
Y
CL = 50 pF
2.8
5.1
7.1
1
8
1
9.5
ns
Y
CL = 50 pF
2.8
6.1
8.8
1
10
1
10
ns
1
ns
CL = 50 pF
1
1
3
SN74LV125AT
QUADRUPLE BUS BUFFER GATE
WITH 3-STATE OUTPUTS
www.ti.com
SCES629A – MAY 2005 – REVISED AUGUST 2005
Noise Characteristics (1)
VCC = 5 V, CL = 50 pF, TA = 25°C
TYP
MAX
VOL(P)
Quiet output, maximum dynamic VOL
MIN
1.1
1.5
V
VOL(V)
Quiet output, minimum dynamic VOL
–0.3
–0.8
V
VOH(V)
Quiet output, minimum dynamic VOH
VIH(D)
High-level dynamic input voltage
VIL(D)
Low-level dynamic input voltage
(1)
3
UNIT
V
2
V
0.8
V
Characteristics are for surface-mount packages only.
Operating Characteristics
VCC = 5 V, TA - 25°C
PARAMETER
Cpd
4
Power dissipation capacitance
TEST CONDITIONS
Outputs enabled
CL = 50 pF,
f = 10 MHz
TYP
16
UNIT
pF
SN74LV125AT
QUADRUPLE BUS BUFFER GATE
WITH 3-STATE OUTPUTS
www.ti.com
SCES629A – MAY 2005 – REVISED AUGUST 2005
PARAMETER MEASUREMENT INFORMATION
VCC
From Output
Under Test
Test
Point
RL = 1 kΩ
From Output
Under Test
CL
(see Note A)
S1
Open
TEST
GND
CL
(see Note A)
LOAD CIRCUIT FOR
TOTEM-POLE OUTPUTS
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open Drain
Open
VCC
GND
VCC
LOAD CIRCUIT FOR
3-STATE AND OPEN-DRAIN OUTPUTS
3V
1.5 V
Timing Input
0V
tw
3V
1.5 V
Input
1.5 V
th
tsu
3V
1.5 V
Data Input
1.5 V
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
1.5 V
Input
1.5 V
0V
tPLH
tPHL
VOH
In-Phase
Output
50% VCC
tPHL
Out-of-Phase
Output
50% VCC
VOL
Output
Waveform 1
S1 at VCC
(see Note B)
VOH
50% VCC
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
1.5 V
1.5 V
0V
tPZL
tPLZ
≈VCC
50% VCC
tPZH
tPLH
50% VCC
3V
Output
Control
Output
Waveform 2
S1 at GND
(see Note B)
VOL + 0.3 V
VOL
tPHZ
50% VCC
VOH − 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 3 ns, tf ≤ 3 ns.
D. The outputs are measured one at a time, with one input transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPHL and tPLH are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
Figure 1. Load Circuits and Voltage Waveforms
5
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
SN74LV125ATD
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
LV125AT
SN74LV125ATDBR
ACTIVE
SSOP
DB
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
LV125AT
SN74LV125ATDR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
LV125AT
SN74LV125ATNSR
ACTIVE
SO
NS
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
LV125AT
SN74LV125ATPWR
ACTIVE
TSSOP
PW
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
LV125AT
SN74LV125ATPWT
ACTIVE
TSSOP
PW
14
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
LV125AT
SN74LV125ATRGYR
ACTIVE
VQFN
RGY
14
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
VV125
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
很抱歉,暂时无法提供与“SN74LV125ATNSG4”相匹配的价格&库存,您可以联系我们找货
免费人工找货